ch15 ism
Post on 26-Oct-2014
240 Views
Preview:
TRANSCRIPT
1539
Chapter 15 Traveling Waves Conceptual Problems 1 • [SSM] A rope hangs vertically from the ceiling. A pulse is sent up the rope. Does the pulse travel faster, slower, or at a constant speed as it moves toward the ceiling? Explain your answer. Determine the Concept The speed of a transverse wave on a rope is given by
μTFv = where FT is the tension in the rope and μ is its linear density. The waves on the rope move faster as they move toward the ceiling because the tension increases due to the weight of the rope below the pulse. 2 • A pulse on a horizontal taut string travels to the right. If the rope’s mass per unit length decreases to the right, what happens to the speed of the pulse as it travels to the right? (a) It slows down. (b) It speeds up. (c) Its speed is constant. (d) You cannot tell from the information given. Determine the Concept The speed v of a pulse on the string varies with the tension FT in the string and its mass per unit length μ according to μTFv = . Because the rope’s mass per unit length decreases to the right, the speed of the pulse increases. ( )b is correct.
3 • As a sinusoidal wave travels past a point on a taut string, the arrival time between successive crests is measured to be 0.20 s. Which of the following is true? (a) The wavelength of the wave is 5.0 m. (b) The frequency of the wave is 5.0 Hz. (c) The velocity of propagation of the wave is 5.0 m/s. (d) The wavelength of the wave is 0.20 m. (e) There is not enough information to justify any of these statements. Determine the Concept The distance between successive crests is one wavelength and the time between successive crests is the period of the wave motion. Thus, T = 0.20 s and f = 1/T = 5.0 Hz. )(b is correct.
4 • Two harmonic waves on identical strings differ only in amplitude. Wave A has an amplitude that is twice that of wave B’s. How do the energies of these waves compare? (a) EA = EB. (b) EA = 2EB. (c) EA = 4EB. (d) There is not enough information to compare their energies. Picture the Problem The average energy transmitted by a wave on a string is proportional to the square of its amplitude and is given by ( ) xAE ΔΔ 22
21
av μω= where A is the amplitude of the wave, μ is the linear density (mass per unit length)
Chapter 15
1540
of the string, ω is the angular frequency of the wave, and Δx is the length of the string. Because the waves on the strings differ only in amplitude, the energy of the wave on string A is given by:
2AA cAE =
Express the energy of the wave on string B:
2BB cAE =
Divide the first of these equations by the second and simplify to obtain:
2
B
A2B
2A
B
A⎟⎟⎠
⎞⎜⎜⎝
⎛==
AA
cAcA
EE
Because AA = 2AB:
422
B
B
B
A =⎟⎟⎠
⎞⎜⎜⎝
⎛=
AA
EE
⇒ BA 4EE =
( )c is correct. 5 • [SSM] To keep all of the lengths of the treble strings (unwrapped steel wires) in a piano all about the same order of magnitude, wires of different linear mass densities are employed. Explain how this allows a piano manufacturer to use wires with lengths that are the same order of magnitude. Determine the Concept The resonant (standing wave) frequencies on a string are inversely proportional to the square root of the linear density of the string ( )λμTTf = . Thus extremely high frequencies (which might otherwise require very long strings) can be accommodated on relatively short strings if the strings are linearly denser that the high frequency strings. High frequencies are not a problem as they utilize short strings anyway. 6 • Musical instruments produce sounds of widely varying frequencies. Which sounds waves have the longer wavelengths? (a) The lower frequencies. (b) The higher frequencies. (c) All frequencies have the same wavelength. (d) There is not enough information to compare the wavelengths of the different frequency sounds. Determine the Concept Once the sound has been produced by a vibrating string, membrane, or air column, the speed with which it propagates is the product of its frequency and wavelength ( ).λfv = For a given medium and temperature, v is constant. Hence the wavelength and frequency for a given sound are inversely proportional and ( )a is correct.
Traveling Waves
1541
7 • In Problem 7, which sound waves have the higher speeds? (a) The lower frequency sounds. (b) The higher frequency sounds. (c) All frequencies have the same wave speed. (d) There is not enough information to compare their speeds. Determine the Concept Once the sound has been produced by a vibrating string, membrane, or air column, the wave speed with which it propagates depends on the properties of the medium in which it is propagating and is independent of the frequency and wavelength of the sound. ( )c is correct.
8 • Sound travels at 343 m/s in air and 1500 m/s in water. A sound of 256 Hz is made under water, but you hear the sound while walking along the side of the pool. In the air, the frequency is (a) the same, but the wavelength of the sound is shorter, (b) higher, but the wavelength of the sound stays the same, (c) lower, but the wavelength of the sound is longer, (d) lower, and the wavelength of the sound is shorter, (e) the same, and the wavelength of the sound stays the same. Determine the Concept In any medium, the wavelength, frequency, and speed of a sound wave are related through λ = v/f. Because the frequency of a wave is determined by its source and is independent of the nature of the medium, if v is greater in water than in air, λ will be greater in water than in air. )(a is correct.
9 • While out on patrol, the battleship Rodger Young hits a mine, begins to burn, and ultimately explodes. Sailor Abel jumps into the water and begins swimming away from the doomed ship, while Sailor Baker gets into a life raft. Comparing their experiences later, Abel tells Baker, ″I was swimming underwater, and heard a big explosion from the ship. When I surfaced, I heard a second explosion. What do you think it could be?″ Baker says, ″I think it was your imagination—I only heard one explosion. ″ Explain why Baker only heard one explosion, while Abel heard two. Determine the Concept There was only one explosion. Sound travels faster in water than air. Abel heard the sound wave in the water first, then, surfacing, heard the sound wave traveling through the air, which took longer to reach him. 10 • True or false: A 60-dB sound has twice the intensity of a 30-dB sound. Picture the Problem The intensity level β, measured in decibels, is given by
( ) ( )0logdB10 II=β where I0 = 10−12 W/m2 is defined to be the threshold of hearing.
Chapter 15
1542
Express the intensity of the 60-dB sound:
( )0
60logdB10dB60II
= ⇒ 06
60 10 II =
Express the intensity of the 30-dB sound:
( )0
30logdB10dB30II
= ⇒ 03
30 10 II =
Because I60 = 103I30, the statement is false.
11 • [SSM] At a given location, two harmonic sound waves have the same amplitude, but the frequency of sound A is twice the frequency of sound B. How do their average energy densities compare? (a) The average energy density of A is twice the average energy density of B. (b) The average energy density of A is four times the average energy density of B. (c) The average energy density of A is 16 times the average energy density of B. (d) You cannot compare the average energy densities from the data given. Determine the Concept The average energy density of a sound wave is given by
20
221
av sρωη = where ρ is the average density of the medium, s0 is the displacement amplitude of the molecules making up the medium, and ω is the angular frequency of the sound waves. Express the average energy density of sound A:
2A,0
2AA2
1A av, sωρη =
The average energy density of sound B is given by:
2B,0
2BB2
1B av, sωρη =
Dividing the first of these equation by the second yields: 2
B,02BB2
1
2A,0
2AA2
1
B av,
A av,
ss
ωρωρ
ηη
=
Because the sound waves are identical except for their frequencies:
2
B
A
2
B
A2B
2A
B av,
A av,
22
⎟⎟⎠
⎞⎜⎜⎝
⎛=⎟⎟
⎠
⎞⎜⎜⎝
⎛==
ff
ff
ππ
ωω
ηη
Because fA = 2fB: 42
2
B
B
B av,
A av, =⎟⎟⎠
⎞⎜⎜⎝
⎛=
ff
ηη
⇒ B av,A av, 4ηη =
( )b is correct.
12 • At a given location, two harmonic sound waves have the same frequency but the amplitude of sound A is twice the amplitude of sound B. How do their average energy densities compare? (a) The average energy density of A is
Traveling Waves
1543
twice the average energy density of B. (b) The average energy density of A is four times the average energy density of B (c) The average energy density of A is 16 times the average energy density of B (d) You cannot compare the average energy densities from the data given. Determine the Concept The average energy density of a sound wave is given by
20
221
av sρωη = where ρ is the average density of the medium, s0 is the displacement amplitude of the molecules making up the medium, and ω is the angular frequency of the sound waves. Express the average energy density of sound A:
2A,0
2AA2
1A av, sωρη =
The average energy density of sound B is given by:
2B,0
2BB2
1B av, sωρη =
Dividing the first of these equation by the second yields: 2
B,02BB2
1
2A,0
2AA2
1
B av,
A av,
ss
ωρωρ
ηη
=
Because the sound waves are identical except for their displacement amplitudes:
2
B,0
A,02
B,0
2A,0
B av,
A av,
⎟⎟⎠
⎞⎜⎜⎝
⎛==
ss
ss
ηη
Because B,0A,0 2ss =
42
2
B,0
B,0
B av,
A av, =⎟⎟⎠
⎞⎜⎜⎝
⎛=
ss
ηη
⇒ B av,A av, 4ηη =
( )b is correct.
13 • What is the ratio of the intensity of normal conversation to the sound intensity of a soft whisper (at a distance of 5.0 m)? (a) 103, (b) 2, (c) 10−3, (d) 1/2. Hint: See Table 15-1. Determine the Concept The problem is asking us for the ratio of the intensities corresponding to normal conversation and a soft whisper. Table 15-1 includes the quantities we need in order to find this ratio. Use Table 15-1 to find the ratio of I/I0, where I0 is the threshold of hearing, for normal conversation:
6
onconversati normal0
10=⎟⎟⎠
⎞⎜⎜⎝
⎛II
Use Table 15-1 to find the ratio of I/I0 for a soft whisper:
3
whispersoft 0
10=⎟⎟⎠
⎞⎜⎜⎝
⎛II
Chapter 15
1544
Dividing the first of these equation by the second yields: 3
3
6
whispersoft 0
onconversati normal0
101010
==
⎟⎟⎠
⎞⎜⎜⎝
⎛
⎟⎟⎠
⎞⎜⎜⎝
⎛
II
II
( )a is correct.
14 • What is the ratio of the intensity level of normal conversation to the sound intensity level of a soft whisper (at a distance of 5.0 m)? (a) 103, (b) 2, (c) 10−3, (d) 1/2. Hint: See Table 15-1. Determine the Concept The problem is asking us for the ratio of the sound intensity levels (decibel levels) corresponding to normal conversation and a soft whisper. Table 15-1 includes the quantities we need in order to find this ratio. From Table 15-1, the sound intensity level corresponding to normal conversation is:
dB 60onconversati
normal =β
From Table 15-1, the sound intensity level corresponding to a soft whisper is:
dB 30whispersoft =β
Dividing the first of these equation by the second yields:
2dB 30dB 60
whispersoft
onconversati normal
==β
β
( )b is correct.
15 • To increase the sound intensity level by 20 dB requires the sound intensity to increase by what factor? (a) 10, (b) 100, (c) 1000, (d) 2. Determine the Concept The sound intensity level is given by
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
log dB 10IIβ where I is the intensity of a given sound and I0 is the
intensity of the threshold of hearing. The sound intensity level for a sound whose intensity is I1 is given by:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
11 log dB 10
IIβ
Traveling Waves
1545
The sound intensity level for a sound whose intensity is I2 is given by:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
22 log dB 10
II
β
Subtract the second equation from the first and simplify to obtain: ( ) ⎟
⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛=−
2
121 log dB 10
IIββ
Solving for I1/I2 yields:
dB 10
2
121
10ββ −
=II
For a 20-dB increase in the sound intensity level:
2dB 10dB 20
2
1 1010 ==II ⇒ ( )b is correct.
16 • You are using a hand-held sound level meter to measure the intensity level of the roars produced by a lion prowling in the high grass. To decrease the measured sound intensity level by 20 dB requires the lion move away from you until its distance from you has increased by what factor? (a) 10, (b) 100, (c) 1000, (d) You cannot tell the required distance from the data given. Determine the Concept The sound intensity level is given by
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
log dB 10IIβ where I is the intensity of a given sound and I0 is the
intensity of the threshold of hearing. The intensity of the a given sound varies
with distance from its source according to 2av
4 rPIπ
= .
The sound intensity level for a sound whose intensity is I1 is given by: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
11 log dB 10
IIβ
The sound intensity level for a sound whose intensity is I2 is given by:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
22 log dB 10
II
β
Subtract the second equation from the first and simplify to obtain: ( ) ⎟
⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛=−
2
121 log dB 10
II
ββ
Solving for I1/I2 yields:
dB 10
2
121
10ββ −
=II
Chapter 15
1546
Letting r1 be the lion’s initial distance from you and r2 be the lion’s final distance from you, substitute for I1 and I2 and simplify to obtain:
dB 102
1
22
22
av
21
av21
10
4
4 ββ
π
π −
==rr
rP
rP
⇒ dB 10
1
221
10ββ −
=rr
For a 20-dB decrease in the sound intensity level: 1010 dB 10
dB 20
1
2 ==rr
⇒ ( )b is correct.
17 • One end of a very light (but strong) thread is attached to an end of a thicker and denser cord. The other end of the thread is fastened to a sturdy post and you pull the other end of the cord so the thread and cord are taut. A pulse is sent down the thicker, denser cord. True or false: (a) The pulse that is reflected back from the thread-cord attachment point is inverted compared to the initial incoming pulse. (b) The pulse that continues past the thread-cord attachment point is not inverted compared to the initial incoming pulse. (c) The pulse that continues past the thread-cord attachment point has an amplitude that is smaller than the pulse that is reflected. (a) False. Because the reflection medium (cord) in which the pulse travels initially has a greater linear density than the transmission medium (thread), there is no phase shift in the reflected pulse. (b) True. Because the thread-cord attachment point of the media is more like a loose end than a fixed end, the pulse transmitted into the light thread is in phase with the incoming pulse in the thicker, denser cord. (c) True. Because the string is attached to a thicker, denser cord, the reflected pulse behaves almost as though it was reflected from a fixed end and is, therefore, inverted. The pulse in the light thread is in phase with the incoming pulse in the thicker, denser cord. Because energy is conserved and there is some energy transmitted and some reflected, the transmitted wave cannot have an amplitude as large as the amplitude of the pulse in the thicker, denser cord. 18 • Light traveling in air strikes a glass surface at an incident angle of 45°. True or false: (a) The angle between the reflected light ray and the incident ray is 90°. (b) The angle between the reflected light ray and the refracted light ray is less than 90°. Determine the Concept The ray diagram shows the relationship between the incident, reflected, and refracted rays.
Traveling Waves
1547
air glass
°45
θ1
rayIncident
ray Reflected
ray Refracted
glassair vv >
(a) True. Because the angle of incidence is equal to the angle of reflection, the sum of these angles in this example is 90°. Note: this is a special case and is not generally true. (b) False. Because light travels slower in glass than in air, the refracted ray makes an angle of less than 45° with the normal. Hence the angle it makes with the reflected ray is greater than 90°. 19 • [SSM] Sound waves in air encounter a 1.0-m wide door into a classroom. Due to the effects of refraction, the sound of which frequency is least likely to be heard by all the students in the room, assuming the room is full? (a) 600 Hz, (b) 300 Hz, (c) 100 Hz, (d) All the sounds are equally likely to be heard in the room. (e) Diffraction depends on wavelength not frequency, so you cannot tell from the data given. Determine the Concept If the wavelength is large relative to the door, the diffraction effects are large and the waves spread out as they pass through the door. Because we’re interested in sounds that are least likely to be heard everywhere in the room, we want the wavelength to be short and the frequency to be high. Hence ( )a is correct.
20 • Microwave radiation in modern microwave ovens has a wavelength on the order of centimeters. Would you expect significant diffraction if this radiation was aimed at a 1.0-m wide door? Explain. Determine the Concept No. Because the wavelength of the radiation is small relative to the door, the diffraction effects are small and the waves do not spread out significantly as they pass through the door. 21 •• [SSM] Stars often occur in pairs revolving around their common center of mass. If one of the stars is a black hole, it is invisible. Explain how the
Chapter 15
1548
existence of such a black hole might be inferred by measuring the Doppler frequency shift of the light observed from the other, visible star. Determine the Concept The light from the visible star will be shifted about its mean frequency periodically due to the relative approach toward and recession away from Earth as the star revolves around the common center of mass. 22 •• Figure 15-30 shows a wave pulse at time t = 0 moving to the right. (a) At this particular time, which segments of the string are moving up? (b) Which segments are moving down? (c) Is there any segment of the string at the pulse that is instantaneously at rest? Answer these questions by sketching the pulse at a slightly later time and a slightly earlier time to see how the segments of the string are moving. Determine the Concept The graph shown below shows the pulse at an earlier time (t < 0) and later time (t > 0). (a) One can see that at t = 0, the portion of the string between 1 cm and 2 cm is moving down, (b) the portion between 2 cm and 3 cm is moving up, and (c) the string at x = 2 cm is instantaneously at rest.
0 1 2 3 4 5 6 7 8 9 10
x , cm
y
t = 0
t > 0
t < 0
23 •• Make a sketch of the velocity of each string segment versus position for the pulse shown in Figure 15-30. Determine the Concept The velocity of the string at t = 0 is shown. Note that the velocity is negative for 1 cm < x < 2 cm and is positive for 2 cm < x < 3 cm.
Traveling Waves
1549
0 1 2 3 4 5 6 7 8 9 10
x , cm
v y
24 •• An object of mass m hangs on a very light rope that is connected to the ceiling. You pluck the rope just above the object, and a wave pulse travels up to the ceiling and back. Compare the round-trip time for such a wave pulse to the round-trip time of a wave pulse on the same rope if an object of mass 9m is hung on the rope instead. (Assume the rope does not stretch, that is, the mass-to-ceiling distance is the same in each case.) Determine the Concept If the mass providing the tension in the rope is increased by a factor of n, then the tension in the rope increases by the same factor and the speed of the pulse on the rope increases by a factor of n and the round trip time for the pulse is decreased by a factor of n1 . Let represent the distance the pulse travels. Then the time for the round trip is given by:
vt = (1)
Express the speed of the wave when the object of mass m provides the tension in the rope:
μm
m
Fv T,=
Express the speed of the wave when the object of mass 9m provides the tension in the rope:
μm
m
Fv T,9
9 =
Substituting for mv9 in equation (1) yields:
mmm FF
tT,9T,9
9μ
μ
== (2)
Similarly, the travel time when the object whose mass is m is providing the tension is given by: mm
m FFt
T,T,
μ
μ
== (3)
Chapter 15
1550
Divide equation (2) by equation (3) and simplify to obtain:
m
m
m
m
FF
tt
T,9
T,9 =
Because mm FF T,T,9 9= :
31
T,
T,9
9==
m
m
m
m
FF
tt
⇒ mm tt 31
9 =
25 •• The explosion of a depth charge beneath the surface of the water is recorded by a helicopter hovering above its surface, as shown in Figure 15-31. Along which path, A, B, or C, will the sound wave take the least time to reach the helicopter? Explain why you chose the path you did. Determine the Concept Path C. Because the wave speed is highest in the water, and more of path C is underwater than A or B, the sound wave will spend the least time on path C. 26 •• Does a speed of Mach 2 at an altitude of 60,000 feet mean the same as a speed of Mach 2 near ground level? Explain clearly. Determine the Concept No. The term Mach 2 means that the speed is twice the speed of sound at a given altitude. Because the speed of sound is lower at high altitudes than at ground level (due to lower density and colder temperature), Mach 2 means less than twice the speed of sound at sea level. Estimation and Approximation 27 •• Many years ago, Olympic 100 m dashes were started by the sound from a starter’s pistol, with the starter positioned several meters down the track, just on the inside of the track. (Today, the pistol that is used is often only a trigger, which is used to electronically activate speakers behind each sprinter’s starting blocks. This method avoids the problem of one runner hearing sound before the other runners.) Estimate the time advantage the inside lane (relative to the runner at the outside lane of 8 runners) would have if all runners started when they heard the sound from the starter’s pistol. Picture the Problem Due to the differences in the distances from the starter to the inside- and outside-lane sprinters, the sound of the starting pistol took more time to reach the outside-lane sprinter than it did to reach the inside-lane sprinter. Express the difference in time for the two sprinters in terms of the distances the sound must travel and the speed of sound:
vv
ttt
lane insidelane outside
lane insidelane ousideΔ
−=
−=
Traveling Waves
1551
Assuming that the separation of the inside- and outside-lane sprinters is w:
22lane insidelane outside w+=
Substitute for lane outside to obtain:
vw
t lane inside22
lane insideΔ−+
=
Assuming that the separation of the inside- and outside-lane sprinters is 7.0 m and that the starter is 5.0 m from the inside-lane sprinter yields:
( ) ( )
ms 11m/s 343
m 0.5m 0.7m 0.5Δ22
=
−+=t
Remarks: Because a 100-m sprint is often decided by one or two hundredths of a second, this difference could be significant. This difference led to the invention of the electronic starter’s sound. 28 •• Estimate the speed of the bullet as it passes through the helium balloon in Figure 15-32. Hint: A protractor would be beneficial. Picture the Problem You can use a protractor to measure the angle of the shock cone and then estimate the speed of the bullet using .sin uv=θ The speed of sound in helium at room temperature (293 K) is 977 m/s. Relate the speed of the bullet u to the speed of sound v in helium and the angle of the shock cone θ :
uv
=θsin ⇒θsin
vu =
Measuring θ yields:
°≈ 70θ
Substitute numerical values and evaluate u: km/s0.1
70sinm/s977
=°
=u
29 •• The new student townhouses at a local college are in the form of a semicircle half-enclosing the track field. To estimate the speed of sound in air, an ambitious physics student stood at the center of the semicircle and clapped his hands rhythmically at a frequency at which he couldn’t hear the echo of the clap, because it reached him at the same time as his next clap. This frequency was about 2.5 claps/s. Once he established this frequency, he paced off the distance to the townhouses, which was 30 double strides. Assuming that the length of each stride is equal to half his height (5 ft 11 in), estimate the speed of sound in air using this data. How far off is this from the commonly accepted value of 343 m/s?
Chapter 15
1552
Picture the Problem Let d be the distance to the townhouses. We can relate the speed of sound to the distance to the townhouses to the frequency of the clapping for which no echo is heard. 5 ft 11 in is equal to 1.8 m. Relate the speed of sound to the distance it travels to the townhouses and back to the elapsed time:
tdv
Δ=
2
Express d in terms of the number of strides and distance covered per stride:
( )( ) m54m/stride8.1strides30 ==d
Relate the elapsed time Δt to the frequency f of the clapping:
s40.0claps/s5.211Δ ===
ft
Substitute numerical values and evaluate v:
( ) km/s27.0m/s 270s40.0
m542===v
The percent difference between this result and 343 m/s is: %21
m/s343m/s270m/s343diff % =
−=
Speed of Waves
30 • (a) The bulk modulus of water is 2.00 × 109 N/m2. Use this value to find the speed of sound in water. (b) The speed of sound in mercury is 1410 m/s. What is the bulk modulus of mercury (ρ = 13.6 × 103 kg/m3)? Picture the Problem The speed of sound in a fluid is given by ρBv = where B is the bulk modulus of the fluid and ρ is its density. (a) Express the speed of sound in water in terms of its bulk modulus:
ρBv =
Substitute numerical values and evaluate v:
km/s1.41
km/s 414.1kg/m101.00N/m102.00
33
29
=
=××
=v
(b) Solving ρBv = for B yields: 2vB ρ=
Substitute numerical values and evaluate B:
( )( )210
233
N/m102.70
m/s1410kg/m1013.6
×=
×=B
Traveling Waves
1553
31 • Calculate the speed of sound waves in hydrogen gas (M = 2.00 g/mol and γ = 1.40) at T = 300 K. Picture the Problem The speed of sound in a gas is given by MRTv γ= where R is the gas constant, T is the absolute temperature, M is the molecular mass of the gas, and γ is a constant that is characteristic of the particular molecular structure of the gas. Because hydrogen gas is diatomic, γ = 1.4. Express the dependence of the speed of sound in hydrogen gas on the absolute temperature:
MRTv γ
=
Substitute numerical values and evaluate v:
( )( )
km/s32.1
kg/mol1000.2K300KJ/mol314.84.1
3
=
×⋅
= −v
32 • A 7.00-m-long guitar string has a mass of 100 g and is under a tension of 900 N. What is the speed of a transverse wave pulse on this string? Picture the Problem The speed of a transverse wave pulse on a string is given by
μTFv = where FT is the tension in the string, m is its mass, L is its length, and μ is its mass per unit length. Express the dependence of the speed of the pulse on the tension in the string:
μTFv = where μ is the mass per unit
length of the string.
Substitute numerical values and evaluate v: m/s251
m7.00kg0.100N900
==v
33 •• [SSM] (a) Compute the derivative of the speed of a wave on a string with respect to the tension dv/dFT, and show that the differentials dv and dFT obey
TT21 FdFvdv = . (b) A wave moves with a speed of 300 m/s on a string that is
under a tension of 500 N. Using to the differential approximation, estimate how much the tension must be changed to increase the speed to 312 m/s. (c) Calculate ΔFT exactly and compare it to the differential approximation result in Part (b). Assume that the string does not stretch with the increase in tension.
Chapter 15
1554
Picture the Problem (a) The speed of a transverse wave on a string is given by μTFv = where TF is the tension in the wire and μ is its linear density. We can
differentiate this expression with respect to FT and then separate the variables to show that the differentials satisfy .TT2
1 FdFvdv = (b) We’ll approximate the differential quantities to determine by how much the tension must be changed to increase the speed of the wave to 312 m/s. (c) We can use μTFv = to obtain an exact expression for ΔFT, (a) Evaluate dv/dFT:
TT
T
T 211
21
Fv
FF
dFd
dFdv
⋅==⎥⎦
⎤⎢⎣
⎡=
μμ
Separate the variables to obtain:
T
T
21
FdF
vdv
=
(b) Solve the equation derived in Part (a) for dFT: v
dvFdF TT 2=
Approximate dFT with ΔFT and dv with Δv to obtain:
vvFF Δ2Δ TT =
Substitute numerical values and evaluate ΔFT: ( )
N40
m/s300m/s 300m/s312N5002Δ T
=
⎟⎟⎠
⎞⎜⎜⎝
⎛ −=F
(c) The exact value for (ΔF)exact is given by:
( ) T,1T,2exactΔ FFF −= (1)
Express the wave speeds for the two tensions: μ
T,11
Fv = and
μT,2
2
Fv =
Dividing the second equation by the first and simplifying yields:
T,1
T,2
T,1
T,2
1
2
v FF
F
Fv
==
μ
μ⇒
2
1
2F,1T,2 ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
vvFF
Traveling Waves
1555
Substituting for FT,2 in equation (1) yields:
( )
⎥⎥⎦
⎤
⎢⎢⎣
⎡−⎟⎟
⎠
⎞⎜⎜⎝
⎛=
−⎟⎟⎠
⎞⎜⎜⎝
⎛=
1
Δ
2
1
2F,1
T,1
2
1
2F,1exactT
vvF
FvvFF
Substitute numerical values and evaluate (ΔFT)exact:
( ) ( )
N 8.40
1m/s 300m/s 312N 500Δ
2
exactT
=
⎥⎥⎦
⎤
⎢⎢⎣
⎡−⎟
⎠⎞
⎜⎝⎛=F
The percent error between the exact and approximate values for ΔFT is:
( )( )
%2
N 8.40N 40.0N 8.40
ΔΔΔ
exactT
TexactT
≈
−=
−F
FF
34 •• (a) Compute the derivative of the speed of sound in air with respect to the absolute temperature, and show that the differentials dv and dT obey
TdTvdv 21= . (b) Use this result to estimate the percentage change in the speed
of sound when the temperature changes from 0 to 27°C. (c) If the speed of sound is 331 m/s at 0°C, estimate its value at 27°C using the differential approximation. (d) How does this approximation compare with the result of an exact calculation? Picture the Problem The speed of sound in a gas is given by MRTv γ= where R is the gas constant, T is the absolute temperature, M is the molecular mass of the gas, and γ is a constant that is characteristic of the particular molecular structure of the gas. We can differentiate this expression with respect to T and then separate the variables to show that the differentials satisfy .2
1 TdTvdv = We’ll approximate the differential quantities to estimate the percentage change in the speed of sound when the temperature increases from 0 to 27°C. Lacking information regarding the nature of the gas, we can express the ratio of the speeds of sound at 300 K and 273 K to obtain an expression that involves just the temperatures. (a) Evaluate dv/dT:
Tv
MR
RTM
MRT
dTd
dTdv
21
21
=
⎟⎠⎞
⎜⎝⎛=⎥
⎦
⎤⎢⎣
⎡=
γγ
γ
Chapter 15
1556
Separate the variables to obtain: TdT
vdv
21
=
(b) Approximate dT with ΔT and dv with Δv and substitute numerical values to obtain:
%0.5K 273
K 273K 30021Δ
=⎟⎠⎞
⎜⎝⎛ −
=vv
(c) Using a differential approximation, approximate the speed of sound at 300 K:
⎟⎠⎞
⎜⎝⎛ Δ
+=
Δ+≈
vvv
vvvvv
1K273
K273K273K300
Substitute numerical values and evaluate v300 K:
( )( )m/s347
0495.01m/s331K300
=
+=v
(d) Use MRTv γ= to express the speed of sound at 300 K:
( )M
Rv K300K300
γ=
Use MRTv γ= to express the speed of sound at 273 K:
( )M
Rv K273K732
γ=
Divide the first of these equations by the second and solve for and evaluate v300 K:
( )
( ) 273300
K273
K300
K273
K300 ==
MR
MR
vv
γ
γ
and
( ) m/s347273300m/s331K300 ==v
Note that these two results agree to three significant figures.
35 ••• Derive a convenient formula for the speed of sound in air at temperature t in Celsius degrees. Begin by writing the temperature as T = T0 + ΔT, where T0 = 273 K corresponds to 0°C and ΔT = t, the Celsius temperature. The speed of sound is a function of T, v(T). To a first-order approximation, you can write ( ) ( ) ( ) TdTdvTvTv T Δ00 +≈ , where
dv / dT( )T 0
is the derivative evaluated at T = T0. Compute this derivative, and show that the result leads to
v = 331 m / s( ) 1+
t2T0
⎛ ⎝ ⎜
⎞ ⎠ ⎟ = 331 + 0.606t( ) m/s.
Traveling Waves
1557
Picture the Problem We can use the approximate expression for v(T) given in the problem statement and the result of Problem 34 to show that
( )m/s 606.0331 tv += . The speed of sound as a function of T is given by:
( ) ( ) TdTdvTvTv
T
Δ0
0 ⎟⎠⎞
⎜⎝⎛+≈ (1)
From Problem 44, dv/dT is given by: ( )
TTv
dtdv
21
=
Evaluating 0TTdT
dv
=⎥⎦⎤ yields:
( )0
0
21
0TTv
dTdv
TT
=⎥⎦⎤
=
(2)
Substitute equation (2) in equation (1) and simplify to obtain: ( ) ( ) ( )
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛+=
⎟⎟⎠
⎞⎜⎜⎝
⎛+≈
00
0
00
2Δ1
Δ21
TTTv
TTTvTvTv
For T0 = 273° K, ( ) m/s 3310 =Tv , and tT =Δ :
( ) ( )( )m/s 606.0331
K 27321m/s 331
t
tv
+=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
The Wave Equation 36 • Show explicitly that the following functions satisfy the wave equation
2
2
22
2 1ty
vxy
∂∂
=∂∂ : (a) y(x,t) = k(x + vt)3, (b) y(x, t) = Aeik(x – vt) , where A and k are
constants and 1−=i , and (c) y(x,t) = ln k(x – vt). Picture the Problem To show that each of the functions satisfies the wave equation, we’ll need to find their first and second derivatives with respect to x and t and then substitute these derivatives in the wave equation. (a) Find the first two spatial derivatives of ( ) ( ) :3vtxktx,y +=
( )23 vtxkxy
+=∂∂
and
( )vtxkxy
+=∂∂ 62
2
(1)
Chapter 15
1558
Find the first two temporal derivatives of ( ) ( ) :3vtxktx,y +=
( )23 vtxkvty
+=∂∂
and
( )vtxkvty
+=∂∂ 2
2
2
6 (2)
Express the ratio of equation (1) to equation (2):
( )( ) 22
2
2
2
2
166
vvtxkvvtxk
ty
xy
=+
+=
∂∂∂∂
confirming that ( ) ( )3, vtxktxy += satisfies the general wave equation.
(b) Find the first two spatial derivatives of ( ) ( )vtxikAetx,y −= :
( )vtxikikAexy −=
∂∂ , ( )vtxikAeki
xy −=
∂∂ 22
2
2
or ( )vtxikAek
xy −−=
∂∂ 2
2
2
(3)
Find the first two temporal derivatives of ( ) ( )vtxikAetx,y −= :
( )vtxikikvAety −−=
∂∂ ,
( )vtxikAevkity −=
∂∂ 222
2
2
or
( )vtxikAevkty −−=
∂∂ 22
2
2
(4)
Express the ratio of equation (3) to equation (4):
( )
( ) 222
2
2
2
2
2
1vAevk
Aek
ty
xy
vtxik
vtxik
=−−
=
∂∂∂∂
−
−
confirming that ( ) ( )vtxikAetxy −=, satisfies the general wave equation.
(c) Find the first two spatial derivatives of
( ) ( )vtxktx,y −= ln : vtx
kxy
−=
∂∂
and
( )2
2
2
2
vtxk
xy
−−=
∂∂ (5)
Traveling Waves
1559
Find the first two temporal derivatives of ( ) ( )vtxktx,y −= ln : vtx
vkty
−−=
∂∂
and
( )2
22
2
2
vtxkv
ty
−−=
∂∂ (6)
Express the ratio of equation (5) to equation (6):
( )
( )2
2
22
2
2
2
2
2
2
1v
vtxkvvtx
k
ty
xy
=
−−
−−
=
∂∂∂∂
confirming that ( ) ( )vtxktx,y −= ln satisfies the general wave equation.
37 • Show that the function y = A sin kx cos ωt satisfies the wave equation.
Picture the Problem The wave equation is 2
2
22
2 1ty
vxy
∂∂
=∂∂ . To show that
tkxAy ωcossin= satisfies this equation, we’ll need to find the first and second derivatives of y with respect to x and t and then substitute these derivatives in the wave equation. Find the first two spatial derivatives of tkxAy ωcossin= : tkxAk
xy ωcoscos=
∂∂
and
tkxAkxy ωcossin22
2
−=∂∂ (1)
Find the first two temporal derivatives of tkxAy ωcossin= : tkxA
ty ωω sinsin−=
∂∂
and
tkxAty ωω cossin22
2
−=∂∂ (2)
Chapter 15
1560
Express the ratio of equation (1) to equation (2):
2
2
2
2
2
2
2
2
2
1
cossincossin
v
ktkxAtkxAk
ty
xy
=
=−−
=
∂∂∂∂
ωωωω
confirming that tkxAy ωcossin= satisfies the general wave equation.
Harmonic Waves on a String 38 • One end of a string 6.0 m long is moved up and down with simple harmonic motion at a frequency of 60 Hz. If the wave crests travel the length of the string in 0.50 s, find the wavelength of the waves on the string. Picture the Problem We can find the wavelength of the waves on the string using the relationship λfv = . Express the wavelength of the waves:
vf =λ ⇒fv
=λ
The speed of the wave is equal to the distance divided by the time:
m/s12s0.50
m6.0ΔΔ
===txv
Substitute numerical values to obtain:
cm20s60m/s12
1 == −λ
39 • [SSM] A harmonic wave on a string with a mass per unit length of 0.050 kg/m and a tension of 80 N, has an amplitude of 5.0 cm. Each point on the string moves with simple harmonic motion at a frequency of 10 Hz. What is the power carried by the wave propagating along the string? Picture the Problem The average power propagated along the string by a harmonic wave is v,AP 22
21
av μω= where v is the speed of the wave, and μ, ω, and A are the linear density of the string, the angular frequency of the wave, and the amplitude of the wave, respectively. Express and evaluate the power propagated along the string:
vAP 2221
av μω=
Traveling Waves
1561
The speed of the wave on the string is given by: μ
TFv =
Substitute for v to obtain: μ
μω T2221
avFAP =
Substitute numerical values and evaluate Pav:
( )( )( ) ( ) W9.9kg/m0.05N80m0.050s10kg/m0.0504 2212
21
av == −πP
40 • A 2.00-m-long rope has a mass of 0.100 kg. The tension is 60.0 N. An oscillator at one end sends a harmonic wave with an amplitude of 1.00 cm down the rope. The other end of the rope is terminated so that all of the energy of the wave is absorbed and none is reflected. What is the frequency of the oscillator if the power transmitted is 100 W? Picture the Problem The average power propagated along the rope by a harmonic wave is v,AP 22
21
av μω= where v is the velocity of the wave, and μ, ω, and A are the linear density of the string, the angular frequency of the wave, and the amplitude of the wave, respectively. Rewrite the power equation in terms of the frequency of the wave:
vAfvAP 2222221
av 2 μπμω ==
Solve for the frequency and simplify to obtain: v
PAvA
Pfμπμπ
av22
av 22
12
==
The wave speed is given by:
μTFv =
Substitute for v and simplify to obtain:
T
av
T
av 22
122
1F
PAF
PA
fμπ
μμ
π==
Chapter 15
1562
Substitute numerical values and evaluate f:
( )( )
( )Hz 171
N 0.60m 2.00kg 0.100
W1002m 0100.02
1=
⎟⎠⎞
⎜⎝⎛
=π
f
41 •• The wave function for a harmonic wave on a string is y(x, t) = (1.00 mm) sin(62.8 m–1 x + 314 s–1 t). (a) In what direction does this wave travel, and what is the wave’s speed? (b) Find the wavelength, frequency, and period of this wave. (c) What is the maximum speed of any point on the string? Picture the Problem ( ) ( )tkxAtxy ω−= sin, describes a wave traveling in the +x direction. For a wave traveling in the −x direction, we have ( ) ( )tkxAtxy ω+= sin, . We can determine A, k, and ω by examination of the wave function. The wavelength, frequency, and period of the wave can, in turn, be determined from k and ω. (a) Because the sign between the kx and ωt terms is positive, the wave is traveling in the −x direction. The speed of the wave is:
m/s00.5m8.62s314
1
1
=== −
−
kv ω
(b) The coefficient of x is k and:
λπ2
=k ⇒kπλ 2
=
Substitute numerical values and evaluate λ:
cm0.10m8.62
21 == −
πλ
The coefficient of t is ω and:
Hz0.502
s3142
1
===−
ππωf
The period of the wave motion is the reciprocal of its frequency:
s0200.0s0.50
111 === −f
T
(c) Express and evaluate the maximum speed of any string segment:
( )( )m/s0.314
rad/s314mm00.1max
=
== ωAv
Traveling Waves
1563
42 •• A harmonic wave on a string with a frequency of 80 Hz and an amplitude of 0.025 m travels in the +x direction with a speed of 12 m/s. (a) Write a suitable wave function for this wave. (b) Find the maximum speed of a point on the string. (c) Find the maximum acceleration of a point on the string. Picture the Problem ( ) ( )tkxAx,ty ω−= sin describes a wave traveling in the +x direction. We can find ω and k from the data included in the problem statement and substitute in the general equation. The maximum speed of a point on the string can be found from ωAv =max and the maximum acceleration from
.2max ωAa =
(a) Express the general form of the equation of a harmonic wave traveling to the right:
( ) ( )tkxAx,ty ω−= sin
Evaluate ω:
( )12
11
s100.5s503s8022
−
−−
×=
=== ππω f
Determine k: 1
1
m42m/s12s503 −
−
===v
k ω
Substitute to obtain: ( ) ( ) ( ) ( )[ ]txx,ty 121 s100.5m42sinm025.0 −− ×−=
(b) The maximum speed of a point on the string is:
( )( )m/s13
s503m0.025 1max
=
== −ωAv
(c) Express the maximum acceleration of a point on the string:
2max ωAa =
Substitute numerical values and evaluate amax:
( )( ) 221max km/s3.6s503m0.025 == −a
43 •• A 200-Hz harmonic wave with an amplitude 1.2 cm moves along a 40-m-long string that has a mass of 0.120 kg and a tension of 50 N. (a) What is the average total energy of the waves on a 20-m-long segment of the string? (b) What is the power transmitted past a given point on the string? Picture the Problem The average power propagated along the string is
.2221
av vAP μω= The average energy on a segment of length L is the average power multiplied by the time for the wave to travel the distance L
Chapter 15
1564
(a) Express the power transmitted past a given point on the string. The average energy passing a point in time t is the average power multiplied by the time:
vAP 2221
av μω= and
tPE avav =
The time for the wave to travel the length L is L/v: v
Lt =
Combine the previous steps and solve for the average energy on the string:
( ) 2222221
222122
21
av
22 ALfAfL
ALvLAvE
μππμ
ωμωμ
==
==
Substitute numerical values and evaluate Eav:
( ) ( )( ) J 8.6m0.012m 20s200m40
kg0.1202 2212av =⎟⎟
⎠
⎞⎜⎜⎝
⎛= −πE
(b) Express Pav: 22
21
av AvP ωμ=
To calculate Pav we need an expression for the wave speed v:
μTFv =
Substitute for v to obtain: ( )
μμπ
μπμ
T222
T2221
av
2
2
FAf
FAfP
=
=
Substitute numerical values and evaluate Pav:
( ) ( ) W44
m 20kg 060.0
N 50m 012.0s 200m 20
kg 060.02 2212av =⎟
⎠⎞
⎜⎝⎛= −πP
44 •• On a real string, some of the energy of the wave dissipates as the wave travels down the string. Such a situation can be described by a wave function whose amplitude A(x) depends on x: y = A(x) sin (kx – ωt) where A(x) = (A0e–bx). What is the power transported by the wave as a function of x, where x > 0?
Traveling Waves
1565
Picture the Problem The power propagated along the string by a harmonic wave is vAP 22
21 μω= where v is the velocity of the wave, and μ, ω, and A are the linear
density of the string, the angular frequency of the wave, and the amplitude of the wave, respectively. Express the power associated with the wave at the origin:
vAP 2221 μω= (1)
Express the amplitude of the wave at x:
( ) bxeAxA −= 0
Substitute in equation (1) to obtain: ( ) ( )bx
bx
veA
veAxP22
02
21
20
221
−
−
=
=
μω
μω
45 •• [SSM] Power is to be transmitted along a taut string by means of transverse harmonic waves. The wave speed is 10 m/s and the linear mass density of the string is 0.010 kg/m. The power source oscillates with an amplitude of 0.50 mm. (a) What average power is transmitted along the string if the frequency is 400 Hz? (b) The power transmitted can be increased by increasing the tension in the string, the frequency of the source, or the amplitude of the waves. By how much would each of these quantities have to increase to cause an increase in power by a factor of 100 if it is the only quantity changed?
Picture the Problem The average power propagated along a string by a harmonic wave is vAP 22
21
av μω= where v is the speed of the wave, and μ, ω, and A are the linear density of the string, the angular frequency of the wave, and the amplitude of the wave, respectively.
(a) Express the average power transmitted along the string:
vAfvAP 2222221
av 2 μπμω ==
Substitute numerical values and evaluate Pav:
( )( )( ) ( )
mW79
m/s10m100.50
s400kg/m0.010223
212av
=
××
=−
−πP
(b) Because 2
av fP ∝ , increasing f by a factor of 10 would increase Pav by a factor of 100.
Chapter 15
1566
Because 2
av AP ∝ , increasing A by a factor of 10 would increase Pav by a factor of 100. Because vP ∝av and Fv ∝ , increasing F by a factor of 100 would increase v by a factor of 100 and Pav by a factor of 100. 46 ••• Two very long strings are tied together at the point x = 0. In the region x < 0, the wave speed is v1, while in the region x > 0, the speed is v2. A sinusoidal wave is incident on the knot from the left (x < 0); part of the wave is reflected and part is transmitted. For x < 0, the displacement of the wave is describable by y(x,t) = A sin (k1x – ωt) + B sin(k1x + ωt), while for x > 0, y(x,t) = C sin (k2x – ωt), where ω/k1 = v1 and ω/k2 = v2. (a) If we assume that both the wave function y and its first spatial derivative ∂y/∂x must be continuous at x = 0, show that C/A = 2v2/( v1 + v2), and that B/A = (v1 – v2)/( v1 + v2). (b) Show that B2 + (v1/v2)C2 = A2. Picture the Problem We can use the assumption that both the wave function and its first spatial derivative are continuous at x = 0 to establish equations relating A, B, C, k1, and k2. Then, we can solve these simultaneous equations to obtain expressions for B and C in terms of A, v1, and v2. (a) Let y1(x, t) represent the wave function in the region x < 0, and y2(x, t) represent the wave function in the region x > 0. Express the continuity of the two wave functions at x = 0:
( ) ( )tyty ,0,0 21 = and
( )[ ] ( )[ ]( )[ ]tkC
tkBtkAω
ωω−=
++−0sin
0sin0sin
2
11
or ( ) ( )tCtBtA ωωω −=+− sinsinsin
Because the sine function is odd; that is, ( ) θθ sinsin −=− :
tCtBtA ωωω sinsinsin −=+− and
CBA =− (1)
Differentiate the wave functions with respect to x to obtain: ( )
( )txkBk
txkAkxy
ω
ω
++
−=∂∂
11
111
cos
cos
and
( )txkCkxy ω−=
∂∂
222 cos
Traveling Waves
1567
Express the continuity of the slopes of the two wave functions at x = 0:
∂y1
∂xx =0
=∂y 2
∂xx =0
and ( )[ ] ( )[ ]
( )[ ]tkCktkBktkAk
ωωω
−=++−
0cos0cos0cos
22
1111
or ( )
( )tCktBktAkω
ωω−=
+−coscoscos
2
11
Because the cosine function is even; that is, ( ) θθ coscos =− :
tCktBktAk ωωω coscoscos 211 =+ and
CkBkAk 211 =+ (2)
Multiply equation (1) by k1 and add it to equation (2) to obtain:
( )CkkAk 2112 +=
Solving for C yields: A
kkA
kkkC
1221
1
122
+=
+=
Solve for C/A and substitute ω/v1 for k1 and ω/v2 for k2 to obtain: 21
2
2112
21
21
2vv
vvvkkA
C+
=+
=+
=
Substitute in equation (1) to obtain:
Avv
vBA ⎟⎟⎠
⎞⎜⎜⎝
⎛+
=−12
22
Solving for B/A yields:
21
21
vvvv
AB
+−
=
Chapter 15
1568
(b) We wish to show that B2 + (v1/v2)C2 = A2 Use the results of (a) to obtain the expressions B = −[(1 − α)/(1 + α)] A and C = 2A/(1 + α), where α = v1/v2. Substitute these expressions into B2 + (v1/v2)C2 = A2 and check to see if the resulting equation is an identity:
( )( )
( )
( )( )( )
11
111
1121
11
421
11
41
11
211
12
11
2
2
2
2
2
2
2
2
22
222
22
22
2
12
=
=++
=+
++
=+
++−
=+
+−
=⎟⎠⎞
⎜⎝⎛
++⎟
⎠⎞
⎜⎝⎛
+−
=⎟⎠⎞
⎜⎝⎛
++⎟
⎠⎞
⎜⎝⎛
+−
=+
αα
ααα
αααα
ααα
αα
αα
αα
αα AAA
ACvvB
The equation is an identity: Therefore, 22
2
12 ACvvB =+
Remarks: Our result in (a) can be checked by considering the limit of B/A as v2/v1 → 0. This limit gives B/A = +1, telling us that the transmitted wave has zero amplitude and the incident and reflected waves superpose to give a standing wave with a node at x = 0. Harmonic Sound Waves 47 • A sound wave in air produces a pressure variation given by
( ) ( )txtxp 3432
cos75.0, −=π , where p is in pascals, x is in meters, and t is in
seconds. Find (a) the pressure amplitude, (b) the wavelength, (c) the frequency, and (d) the wave speed. Picture the Problem The pressure variation is of the form
( ) ( )vtxkpx,tp −= cos0 where k is the wave number, p0 is the pressure amplitude, and v is the wave speed. We can find λ from k and f from ω and k. (a) By inspection of the equation: Pa75.00 =p
Traveling Waves
1569
(b) Because :2
2 πλπ
==k
m00.4=λ
(c) Solve k
fk
v πω 2== for f to obtain:
π2
kvf =
Substitute numerical values and evaluate f:
( )Hz8.85
2
m/s3432 ==
π
π
f
(d) By inspection of the equation: m/s343=v
48 • (a) Middle C on the musical scale has a frequency of 262 Hz. What is the wavelength of this note in air? (b) The frequency of the C an octave above middle C is twice that of middle C. What is the wavelength of this note in air? Picture the Problem The frequency, wavelength, and speed of the sound waves are related by v = fλ. (a) The wavelength of middle C is given by:
m30.1s262m/s340
1 === −fvλ
(b) Evaluate λ for a frequency twice that of middle C: ( ) m649.0
s2622m/s340
1 === −fvλ
49 • [SSM] (a) What is the displacement amplitude for a sound wave with a frequency of 100 Hz and a pressure amplitude of 1.00 × 10–4 atm? (b) The displacement amplitude of a sound wave of frequency 300 Hz is 1.00 ×10–7 m. Assuming the density of air is 1.29 kg/m3, what is the pressure amplitude of this wave? Picture the Problem The pressure amplitude depends on the density of the medium ρ, the angular frequency of the sound wave μ, the speed of the wave v, and the displacement amplitude s0 according to .00 vsp ρω= (a) Solve 00 vsp ρω= for s0:
vps
ρω0
0 =
Chapter 15
1570
Substitute numerical values and evaluate s0:
( )( )( )( )( ) m 4.36m 1064.3
m/s 343s 100kg/m 1.292Pa/atm 1001325.1atm 1000.1 5
13
54
0 μπ
=×=××
= −−
−
s
(b) Use 00 vsp ρω= to find p0:
( )( )( )( ) mPa4.83m101.00m/s343s300kg/m29.12 7130 =×= −−πp
50 • (a) What is the displacement amplitude of a sound wave that has a frequency of 500 Hz at the pain-threshold pressure amplitude of 29.0 Pa? (b) Assuming the density of air is 1.29 kg/m3, what is the displacement amplitude of a sound wave that has the same pressure amplitude as the wave in Part (a), but has a frequency of 1.00 kHz? Picture the Problem The pressure amplitude depends on the density of the medium ρ, the angular frequency of the sound wave μ, the wave speed v, and the displacement amplitude s0 according to 00 vsp ρω= . (a) Solve 00 vsp ρω= for s0:
vps
ρω0
0 =
Substitute numerical values and evaluate s0: ( )( )( )
m9.20
m/s343Hz500kg/m1.292Pa0.29
30
μ=
=π
s
(b) Proceed as in (a) with f = 1.00 kHz: ( )( )( )
m4.10
m/s343kHz 00.1kg/m1.292Pa0.29
30
μ=
=π
s
51 • A typical loud sound wave that has a frequency of 1.00 kHz has a pressure amplitude of about 1.00 × 10–4 atm. (a) At t = 0, the pressure is a maximum at some point x1. What is the displacement at that point at t = 0? (b) Assuming the density of air is 1.29 kg/m3, what is the maximum value of the displacement at any time and place? Picture the Problem The pressure or density wave is 90° out of phase with the displacement wave. When the displacement is zero, the pressure and density changes are either a maximum or a minimum. When the displacement is a
Traveling Waves
1571
maximum or minimum, the pressure and density changes are zero. We can use 00 vsp ρω= to find the maximum value of the displacement at any time and place.
(a) If the pressure is a maximum at x1 when t = 0, the displacement s is zero. (b) Solve 00 vsp ρω= for s0:
vps
ρω0
0 =
Substitute numerical values and evaluate s0:
( )( )( )( )( ) m64.3
m/s343kHz 1.00kg/m1.292Pa/atm101.01325atm101.00
3
54
0 μ=××
=−
πs
52 • An octave represents a change in frequency by a factor of two. Over how many octaves can a typical person hear? Picture the Problem A human can hear sounds between roughly 20 Hz and 20 kHz; a factor of 1000. An octave represents a change in frequency by a factor of 2. We can evaluate 2N = 1000 to find the number of octaves heard by a person who can hear this range of frequencies. Relate the number of octaves to the difference between 20 kHz and 20 Hz:
10002 =N
Take the logarithm of both sides of the equation to obtain:
310log2log =N ⇒ 32log =N
Solving for N yields: 1097.9
2log3
≈==N
53 •• In the oceans, whales communicate by sound transmission through the water. A whale emits a sound of 50.0 Hz to tell a wayward calf to catch up to the pod. The speed of sound in water is about 1500 m/s. (a) How long does it take the sound to reach the calf if he is 1.20 km away? (b) What is the wavelength of this sound in the water? (c) If the whales are close to the surface, some of the sound energy might refract out into the air. What would be the frequency and wavelength of the sound in the air?
Chapter 15
1572
Picture the Problem (a) We can use the definition of average speed to find the time required for the sound to travel to the calf. (b) We can use the relationship between wavelength, frequency, and speed to find the wavelength of the sound in water. (c) The frequency of the sound does not change as it travels from water to air, but its wavelength changes because of the difference in the speed of sound in water and in air. (a) Relate the time it takes the sound to reach the calf to the distance from the whale to the calf and the speed of sound in water:
s 80.0m/s1500km 20.1Δ ===
vdt
(b) The wavelength of this sound in water is the ratio of its speed in water to its frequency:
m 30Hz 50.0m/s 1500water
water ===f
vλ
(c) Because the frequency does not change as it travels from water to air:
Hz 0.50=f
The wavelength of this sound in air is the ratio of its speed in air to its frequency:
m .866Hz 50.0
m/s 433airair ===
fv
λ
Waves in Three Dimensions: Intensity 54 • A spherical sinusoidal source radiates sound uniformly in all directions. At a distance of 10.0 m, the sound intensity level is 1.00 × 10–4 W/m2. (a) At what distance from the source is the intensity 1.00 × 10–6 W/m2? (b) What power is radiated by this source? Picture the Problem The intensity of the sound from the spherical sinusoidal source varies inversely with the square of the distance from the source. The power radiated by the source is the product of the intensity of the radiation and the surface area over which it is distributed. (a) Relate the intensity at 10.0 m to the distance from the source: 2
av
4 rPIπ
=
or
( )2av24
m 0.104 W/m1000.1
πP
=× −
Traveling Waves
1573
Letting r′ represent the distance at which the intensity is 10−6 W/m2, express the intensity as above:
2av26
4W/m1000.1
r'Pπ
=× −
Divide the first of these equations by the second to obtain: ( )
2av
2av
26
24
4
m0.104W/m1000.1W/m1000.1
r'P
P
π
π=
××
−
−
Solving for r′ yields: ( )( ) m100m0.101000.1 22 =×=r'
(b) Solve 2av
4 rPIπ
= for Pav:
IrP 2av 4π=
Substitute numerical values and evaluate Pav:
( ) ( )mW126
W/m1000.1m0.104 242av
=
×= −πP
55 • [SSM] A loudspeaker at a rock concert generates a sound that has an intensity level equal to 1.00 × 10–2 W/m2 at 20.0 m and has a frequency of 1.00 kHz. Assume that the speaker spreads its energy uniformly in three dimensions. (a) What is the total acoustic power output of the speaker? (b) At what distance will the sound intensity be at the pain threshold of 1.00 W/m2? (c) What is the sound intensity at 30.0 m? Picture the Problem Because the power radiated by the loudspeaker is the product of the intensity of the sound and the area over which it is distributed, we can use this relationship to find the average power, the intensity of the radiation, or the distance to the speaker for a given intensity or average power. (a) Use IrP 2
av 4π= to find the total acoustic power output of the speaker:
( ) ( )W3.50 W27.50
W/m1000.1m0.204 222av
==
×= −πP
(b) Relate the intensity of the sound at 20 m to the distance from the speaker:
( )2av22
m 0.204 W/m1000.1
πP
=× −
Relate the threshold-of-pain intensity to the distance from the speaker:
2av2
4W/m00.1
rPπ
=
Chapter 15
1574
Divide the first of these equations by the second and solve for r:
( )( ) m00.2m0.201000.1 22 =×= −r
(c) Use 2av
4 rPIπ
= to find the
intensity at 30.0 m:
( )( )
23
2
W/m1045.4
m0.304W3.50m0.30
−×=
=π
I
56 •• When a pin of mass 0.100 g is dropped from a height of 1.00 m, 0.050 percent of its energy is converted into a sound pulse that has a duration of 0.100 s. (a) Estimate how far away the dropped pin can be heard if the minimum audible intensity is 1.00 × 10–11 W/m2. (b) Your result in Part (a) is much too large in practice because of background noise. If you assume that the intensity must be at least 1.00 × 10–8 W/m2 for the sound to be heard, estimate how far away the dropped pin can be heard. (In both parts, assume that the intensity is P/4πr2.) Picture the Problem We can use conservation of energy to find the acoustical energy resulting from the dropping of the pin. The power developed can then be found from the given time during which the energy was transformed from mechanical to acoustical form. We can find the range at which the dropped pin can be heard from I = P/4π r2. (a) Assuming that I = P/4π r2, express the distance at which one can hear the dropped pin:
IPrπ4
=
Use conservation of energy to determine the sound energy generated when the pin falls:
( )( )( )( )
J10905.4m00.1m/s81.9
kg10100.000050.0
7
2
3
−
−
×=
×
×=
= mghE ε
The power of the sound pulse is given by:
W104.905s0.100
J104.905Δ
6
7
−
−
×=
×==
tEP
Substitute numerical values and evaluate r: ( )
km20.0
W/m1000.14W10905.4
211
6
=
××
= −
−
πr
(b) Repeat the last step in (a) with I = 1.00 × 10–8 W/m2: ( ) m2.6
W/m1000.14W10905.4
28
6
=××
= −
−
πr
Traveling Waves
1575
*Intensity Level 57 • [SSM] What is the intensity level in decibels of a sound wave of intensity (a) 1.00 × 10–10 W/m2 and (b) 1.00 × 10–2 W/m2? Picture the Problem The intensity level β of a sound wave, measured in decibels, is given by ( ) ( )0logdB10 II=β where I0 = 10−12 W/m2 is defined to be the threshold of hearing. (a) Using its definition, calculate the intensity level of a sound wave whose intensity is 1.00 × 10–10 W/m2:
( )
dB0.2010log10
W/m10W/m101.00logdB10
2
212
201
==
⎟⎟⎠
⎞⎜⎜⎝
⎛ ×= −
−
β
(b) Proceed as in (a) with I = 1.00 × 10–2 W/m2: ( )
dB10010log10
W/m10W/m101.00logdB10
10
212
22
==
⎟⎟⎠
⎞⎜⎜⎝
⎛ ×= −
−
β
58 • What is the intensity of a sound wave if, at a particular location, the intensity level is (a) β = 10 dB and (b) β = 3 dB? Picture the Problem (a) and (b) The intensity level β of a sound wave, measured in decibels, is given by ( ) ( )0logdB10 II=β where I0 = 10−12 W/m2 is defined to be the threshold of hearing. (a) Solve ( ) ( )0logdB10 II=β for I to obtain:
( )0
dB1010 II β=
Evaluate I for β = 10 dB: ( ) ( )
( ) 211212
00dB10dB10
W/m10W/m1010
1010−− ==
== III
(b) Proceed as in (a) with β = 3 dB: ( ) ( )
( ) 212212
00dB10dB3
W/m102W/m102
210−− ×==
== III
59 • At a certain distance, the sound intensity level of a dog’s bark is 50 dB. At that same distance, the sound intensity level of a rock concert is 10,000 times that of the dog’s bark. What is the sound intensity level of the rock concert?
Chapter 15
1576
Picture the Problem The intensity level β of a sound wave, measured in decibels, is given by ( ) ( )0logdB10 II=β where I0 = 10−12 W/m2 is defined to be the threshold of hearing. Express the sound level of the rock concert: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
concertconcert logdB10
IIβ (1)
Express the sound level of the dog’s bark: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
doglogdB10dB50I
I
Solve for the intensity of the dog’s bark:
( )27
21250
5dog
W/m10
W/m101010−
−
=
== II
Express the intensity of the rock concert in terms of the intensity of the dog’s bark:
( )23
274dog
4concert
W/m10
W/m101010−
−
=
== II
Substitute in equation (1) and evaluate βconcert:
( )
( ) dB9010logdB10
W/m10W/m10logdB10
9
212
23
concert
==
⎟⎟⎠
⎞⎜⎜⎝
⎛= −
−
β
60 • What fraction of the acoustic power of a noise would have to be eliminated to lower its sound intensity level from 90 to 70 dB? Picture the Problem We can express the intensity levels at both 90 dB and 70 dB in terms of the intensities of the sound at those levels. By subtracting the two expressions, we can solve for the ratio of the intensities at the two levels and then find the fractional change in the intensity that corresponds to a decrease in intensity level from 90 dB to 70 dB. Express the intensity level at 90 dB: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
90logdB10dB90II
Express the intensity level at 70 dB: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
70logdB10dB70II
Traveling Waves
1577
Express Δβ = β90 − β70:
( ) ( )
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎟⎟⎠
⎞⎜⎜⎝
⎛−⎟⎟
⎠
⎞⎜⎜⎝
⎛=
=Δ
70
90
0
70
0
90
logdB10
logdB10logdB10
dB20
II
II
II
β
Solving for I90 yields: 7090 100II =
Express the fractional change in the intensity from 90 dB to 70 dB:
%99100
100
70
7070
90
7090 =−
=−
III
III
Because IP ∝ , the fractional change in power is %99 .
61 •• A spherical source radiates sound uniformly in all directions. At a distance of 10 m, the sound intensity level is 80 dB. (a) At what distance from the source is the intensity level 60 dB? (b) What power is radiated by this source? Picture the Problem The intensity at a distance r from a spherical source varies with distance from the source according to .4 2
av rPI π= We can use this relationship to relate the intensities corresponding to an 80-dB intensity level (I80) and the intensity corresponding to a 60-dB intensity level (I60) to their distances from the source. We can relate the intensities to the intensity levels through ( ) ( )0logdB10 II=β . (a) Express the intensity of the sound where the intensity level is 80 dB: 2
80
av80 4 r
PIπ
=
Express the intensity of the sound where the intensity level is 60 dB:
260
av60 4 r
PIπ
=
Divide the first of these equations by the second to obtain:
( )2
260
260
av
2av
60
80
m1004
m104 r
rP
P
II
==
π
π
Solving for r60 yields: ( )
60
8060 m10
II
r =
Chapter 15
1578
Find the intensity of the 80-dB sound level radiation: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
80logdB10dB80II
and 24
08
80 W/m1010 −== II
Find the intensity of the 60-dB sound level radiation: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
60logdB10dB60II
and 26
06
60 W/m1010 −== II
Substitute numerical values for I80 and I60 and evaluate r60: ( ) km10.0
W/m10W/m10m10 26
24
60 == −
−
r
(b) Using the intensity corresponding to an intensity level of 80 dB, express and evaluate the power radiated by this source:
( ) ( )[ ]W13.0
m104πW/m10 22480
=
== −AIP
62 •• Harry and Sally are sitting on opposite sides of a circus tent when an elephant trumpets a loud blast. If Harry experiences a sound intensity level of 65 dB and Sally experiences only 55 dB, what is the ratio of the distance between Sally and the elephant to the distance between Harry and the elephant? Picture the Problem The intensity of the sound heard by Harry and Sally depends inversely on the square of the distance between the elephant and each of them. We can use the definition of sound intensity (decibel) level ( ( ) ( )0logdB 10 II=β ) and the definition of intensity ( API av= ) to find the ratio of these distances. Express the sound intensity level at Harry’s location:
( )
( )0
2H
av
0
HH
4logdB 10
logdB 10
IrP
II
π
β
=
=
Similarly, the sound intensity level at Sally’s location is:
( )0
2S
avS 4
logdB 10Ir
Pπ
β =
The difference in decibel level’s at the two locations is given by:
SHΔ βββ −=
Traveling Waves
1579
Substituting for βH, βS, and Δβ yields:
( ) ( ) dB 10dB 55dB 654
logdB 104
logdB 10Δ0
2S
av
02
H
av =−=−=Ir
PIr
Pππ
β
Simplifying this expression yields: 1log 2
H
2S =
rr
⇒ 12
H
2S 10=
rr
Solving for the ratio HS rr yields:
2.310H
S ==rr
63 •• Three noise sources produce intensity levels of 70, 73, and 80 dB when acting separately. When the sources act together, the resultant intensity is the sum of the individual intensities. (a) Find the sound intensity level in decibels when the three sources act at the same time. (b) Discuss the effectiveness of eliminating the two least intense sources in reducing the intensity level of the noise. Picture the Problem We can find the intensities of the three sources from their intensity levels and, because their intensities are additive, find the intensity level when all three sources are acting. (a) Express the sound intensity level when the three sources act at the same time:
( )
( )0
807370
0
sources3sources3
logdB10
logdB10
IIII
II
++=
=β
Find the intensities of each of the three sources:
( ) 07
700
70 10logdB10dB70 IIII
=⇒=
( ) 03.7
730
73 10logdB10dB73 IIII
=⇒=
and
( ) 08
800
80 10logdB10dB80 IIII
=⇒=
Substituting in the expression for β3 sources yields:
( ) ( ) ( )
dB81
101010logdB10101010logdB10 83.77
0
08
03.7
07
sources3
=
++=++
=I
IIIβ
Chapter 15
1580
(b) Find the intensity level with the two least intense sources eliminated: ( ) dB8010logdB10
0
08
80 ==I
Iβ
Eliminating the two least intense sources does not reduce the intensity level significantly. 64 •• Show that if two people are different distances away from a sound source, the difference Δβ between the intensity levels reaching the people, in decibels, will always be the same, no matter the power radiated by the source. Picture the Problem Let the two people be identified by the numerals 1 and 2 and use the definition of the intensity level, in decibels, to express Δβ as a function of the distances r1 and r2 of the two people from the source. Express the difference in the sound intensity level heard by the two people:
12Δ βββ −=
The sound level intensity (decibel level) heard by the second person is given by:
( ) ( )
( )0
22
av
02
av
0
22
4logdB 10
logdB 10logdB 10
IrP
IAP
II
π
β
=
==
In like manner: ( )
02
1
av1 4
logdB 10Ir
Pπ
β =
Substitute in the expression for Δβ to obtain:
( ) ( )0
21
av
02
2
av
4logdB 10
4logdB 10Δ
IrP
IrP
ππβ −=
Simplifying yields: ( )
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎟⎟⎟⎟
⎠
⎞
⎜⎜⎜⎜
⎝
⎛
=
22
21
02
1
av
02
2
av
logdB 10
4
4logdB 10Δ
rr
IrP
IrP
π
πβ
This result shows that the difference in sound level intensities depends only on the distances to the source and not on the source’s power output.
Traveling Waves
1581
65 ••• Everyone at a party is talking equally loudly. One person is talking to you and the sound intensity level at your location is 72 dB. Assuming that all 38 people at the party are at the same distance from you as the person who you are talking to, find the sound intensity level at your location. Picture the Problem The sound intensity level can be found from the intensity of the sound due to the 38 people. When 38 people are talking, the intensities add. Express the sound level when all 38 people are talking: ( )
( ) ( )
( )dB88
dB7238logdB10
logdB1038logdB10
38logdB10
0
1
0
138
=
+=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
⎟⎟⎠
⎞⎜⎜⎝
⎛=
II
II
β
An equivalent but longer solution:
Express the sound intensity level when all 38 people are talking:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
138
38logdB10I
Iβ
Express the sound intensity level when only one person is talking: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛==
0
11 logdB10dB72
II
β
Solving for I1 yields: ( )
25
2122.70
2.71
W/m101.58
W/m101010−
−
×=
== II
Express the sound intensity when all 38 people are talking:
138 38II =
The sound intensity level is: ( ) ( )
dB88
W/m10W/m101.5838logdB10 212
25
38
=
×= −
−
β
66 ••• When a violinist pulls the bow across a string, the force with which the bow is pulled is fairly small, about 0.60 N. Suppose the bow travels across the A string, which vibrates at 440 Hz, at 0.50 m/s. A listener 35 m from the performer hears a sound of 60-dB intensity. Assuming that the sound radiates uniformly in
Chapter 15
1582
all directions, with what efficiency is the mechanical energy of bowing converted to sound energy? Picture the Problem Let η represent the efficiency with which mechanical energy is converted to sound energy. Because we’re given information regarding the rate at which mechanical energy is delivered to the string and the rate at which sound energy arrives at the location of the listener, we’ll take the efficiency to be the ratio of the sound power delivered to the listener divided by the power delivered to the string. We can calculate the power input directly from the given data. We’ll calculate the intensity of the sound at 35 m from its intensity level at that distance and use this result to find the power output. Express the efficiency of the conversion of mechanical energy to sound energy:
in
out
PP
=η
Find the power delivered by the bow to the string:
( )( ) W0.30m/s0.50N0.60in === FvP
Using ( ) ( )0logdB10 II=β , find the intensity of the sound at 35 m:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
m35logdB10dB60I
I
and 26
06
m35 W/m1000.110 −×== II
The rate at which sound energy is emitted is given by:
( )( )W0.0154
m35W/m101.004π 226out
=×== −IAP
Substitute numerical values and evaluate η:
%1.5W0.30W0.0154
==η
67 ••• [SSM] The noise intensity level at some location in an empty examination hall is 40 dB. When 100 students are writing an exam, the noise level at that location increases to 60 dB. Assuming that the noise produced by each student contributes an equal amount of acoustic power, find the noise intensity level at that location when 50 students have left. Picture the Problem Because the sound intensities are additive, we’ll find the noise intensity level due to one student by subtracting the background noise intensity from the intensity due to the students and dividing by 100. Then, we’ll use this result to calculate the intensity level due to 50 students.
Traveling Waves
1583
Express the intensity level due to 50 students:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
0
150
50logdB10I
Iβ
Find the sound intensity when 100 students are writing the exam: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
100logdB10dB60I
I
and 26
06
100 W/m1010 −== II
Find the sound intensity due to the background noise: ( ) ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
0
backgroundlogdB10dB40I
I
and 28
04
background W/m1010 −== II
Express the sound intensity due to the 100 students: 26
2826background100
W/m10
W/m10W/m10−
−−
≈
−=− II
Find the sound intensity due to 1 student:
28background100 W/m10100
−=− II
Substitute numerical values and evaluate the noise intensity level due to 50 students:
( ) ( )
dB57
W/m10W/m101.0050logdB10 212
28
50
=
×= −
−
β
String Waves Experiencing Speed Changes
68 • A 3.00-m-long piece of string with a mass of 25.0 g is tied to 4.00 m of heavy twine with a mass of 75.0 g and the combination is put under a tension of 100 N. If a transverse pulse is sent down the less dense string, determine the reflection and transmission coefficients at the junction point. Picture the Problem Let the subscript ″s″ refer to the string and the subscript ″t″ to the heavy twine. We can use the definitions of the reflection and transmission coefficients and the expression for the speed of waves on a string (Equation 15-3) to find the speeds of the pulse on the string and the heavy twine.
Chapter 15
1584
Use their definitions to express the reflection and transmission coefficients: t
s
t
s
st
st
1
1
vvvv
vvvvr
+
−=
+−
= (1)
and
t
sst
t
1
22
vvvv
v
+=
+=τ (2)
Use Equation 15-3 to express vt and vs: t
Tt μ
Fv = and s
Ts μ
Fv =
Dividing the expression for vs by the expression for vt and simplifying yields: s
t
t
T
s
T
t
s
μμ
μ
μ==
F
F
vv
Substitute for t
s
vv in equation (1) to
obtain:
s
t
s
t
1
1
μμμμ
+
−=r (3)
Express the ratio of μt to μs:
ts
st
s
s
t
t
s
t
mm
m
m
==μμ
Substituting in equation (3) yields:
ts
st
ts
st
1
1
mmmm
r+
−=
Substitute numerical values and evaluate r:
( )( )( )( )( )( )( )( )20.0
m 00.4kg 100.25m 00.3kg 100.751
m 00.4kg 100.25m 00.3kg 100.751
3
3
3
3
−=
××
+
××
−=
−
−
−
−
r
Traveling Waves
1585
Substitute for t
s
vv in equation (2) to
obtain: ts
st
s
t 1
2
1
2
mm
+=
+=
μμ
τ
Substitute numerical values and evaluateτ:
( )( )( )( )
80.0
m 00.4kg 100.25m 00.3kg 100.751
2
3
3
=
××
+
=
−
−τ
Remarks: Because 1=+τr , we could have used this relationship to find τ. 69 • [SSM] Consider a taut string with a mass per unit length μ1, carrying transverse wave pulses that are incident upon a point where the string connects to a second string with a mass per unit length μ2. (a) Show that if μ2 = μ1, then the reflection coefficient r equals zero and the transmission coefficient τ equals +1. (b) Show that if μ2 >> μ1, then r ≈ –1 and τ ≈ 0; and (c) if μ2 << μ1 then r ≈ +1 and τ ≈ +2. Picture the Problem We can use the definitions of the reflection and transmission coefficients and the expression for the speed of waves on a string (Equation 15-3) to r and t in terms of the linear densities of the strings. (a) Use their definitions to express the reflection and transmission coefficients: 2
1
2
1
12
12
1
1
vvvv
vvvvr
+
−=
+−
= (1)
and
2
112
2
1
22
vvvv
v
+=
+=τ (2)
Use Equation 15-3 to express v2 and v1: 2
T2 μ
Fv = and 1
T1 μ
Fv =
Dividing the expression for v1 by the expression for v2 and simplifying yields: 1
2
2
T
1
T
2
1
μμ
μ
μ==
F
F
vv
Chapter 15
1586
Substitute for 2
1
vv in equation (1) to
obtain:
1
2
1
2
1
1
μμμμ
+
−=r (3)
Substitute for 2
1
vv in equation (2) to
obtain: 1
21
2
μμ
τ+
= (4)
If μ2 = μ1: 0
1111
=+−
=r
and
111
2
1
2
1
2
=+
=+
=
μμ
τ
(b) From equations (1) and (2), if μ2 >> μ1 then v1 >> v2:
11
1
12
12 −=−
≈+−
=vv
vvvvr
and
01
22
2
112
2 ≈+
=+
=
vvvv
vτ
(c) If μ2 << μ1, then v2 >> v1: 1
1
1
2
1
2
1
12
12 ≈+
−=
+−
=
vvvv
vvvvr
and
21
22
2
112
2 ≈+
=+
=
vvvv
vτ
70 •• Verify the validity of ( ) 2
2121 τvvr += (Equation 15-36) by
substituting the expressions for r and τ into it. Picture the Problem Making the indicated substitutions will lead us to the identity 1 = 1.
Traveling Waves
1587
The reflection and transmission coefficients are given by: 12
12
vvvvr
+−
= and12
22vv
v+
=τ
Substituting into the equation given in the problem statement yields:
2
12
2
2
1
2
12
12 21 ⎟⎟⎠
⎞⎜⎜⎝
⎛+
+⎟⎟⎠
⎞⎜⎜⎝
⎛+−
=vv
vvv
vvvv
Simplify this expression algebraically to obtain:
( )
( ) ( ) ( )( )( )
1
2424
1 212
212
212
2112
22
212
122112
22
212
2
122
212
=
++
=+
++=
+++−
=+
⎟⎟⎠
⎞⎜⎜⎝
⎛+−
=vvvv
vvvvvv
vvvvvvvv
vvvvvvv
71 ••• Consider a taut string that has a mass per unit length μ1 carrying transverse wave pulses of the form y = f(x – v1t) that are incident upon a point P where the string connects to a second string with mass per unit length μ2. Derive
( ) 221
21 τvvr += by equating the power incident on point P to the power reflected at P plus the power transmitted at P. Picture the Problem Choose the direction of propagation of the incident pulse as the positive x direction and let x = 0 at point P. Energy is conserved as the incident pulse is partially reflected and partially transmitted at point P. From the conservation of energy we have:
trin PPP =+ (1)
From Equation 15-20, the power transmitted in the direction of increasing x is given by:
xy
xyFP
∂∂
∂∂
−= T
Substituting in equation (1) yields:
⎟⎠⎞
⎜⎝⎛
∂∂
∂∂
−=⎟⎠⎞
⎜⎝⎛
∂∂
∂∂
−+⎟⎠⎞
⎜⎝⎛
∂∂
∂∂
−xy
xyF
xy
xyF
xy
xyF tt
Trr
Tinin
T
or, upon simplification,
xy
xy
xy
xy
xy
xy
∂∂
∂∂
=∂∂
∂∂
+∂
∂∂
∂ ttrrinin (2)
Chapter 15
1588
Because the incident pulse is given by ( )tvxfy 1in −= , the reflected and transmitted pulses are given by:
( )tvxrfy 1r −−= and
[ ]⎟⎟⎠
⎞⎜⎜⎝
⎛−= tvx
vvfy 2
2
1t τ
Evaluating xy
∂∂ and
ty
∂∂ using the
chain rule yields:
xddf
xy
∂∂
=∂∂ η
ηand
tddf
ty
∂∂
=∂∂ η
η
where η is the argument of the wave function.
For the transmitted pulse: [ ]2
12
2
1t
vv
ddftvx
vv
xddf
xy
ητ
ητ =⎟⎟
⎠
⎞⎜⎜⎝
⎛−
∂∂
=∂∂
and
[ ] ( )
ητ
ητ
ητ
ddfv
vddftvx
vv
tddf
ty
1
122
1t
−=
−=⎟⎟⎠
⎞⎜⎜⎝
⎛−
∂∂
=∂∂
For the reflected pulse: ( )
ηη ddfrtvx
xddfr
xy
−=−−∂∂
=∂∂
1r
and
( ) ( )
η
ηη
ddfrv
vddfrtvx
tddfr
ty
1
11r
−=
−=−−∂∂
=∂∂
For the incident pulse: ( )
ηη ddftvx
xddf
xy
=−∂∂
=∂
∂1
in
and
( ) ( )
η
ηη
ddfv
vddftvx
tddf
ty
1
11in
−=
−=−∂∂
=∂
∂
Substitute in equation (2) to obtain:
⎟⎟⎠
⎞⎜⎜⎝
⎛−⎟⎟
⎠
⎞⎜⎜⎝
⎛=⎟⎟
⎠
⎞⎜⎜⎝
⎛−⎟⎟
⎠
⎞⎜⎜⎝
⎛−+⎟⎟
⎠
⎞⎜⎜⎝
⎛−
ητ
ητ
ηηηη ddfv
vv
ddf
ddfrv
ddfr
ddfv
ddf
12
111
Traveling Waves
1589
Simplifying and rearranging terms yields:
2
2
121 τvvr +=
The Doppler Effect 72 • A sound source is moving at 80 m/s toward a stationary listener that is standing in still air. (a) Find the wavelength of the sound in the region between the source and the listener. (b) Find the frequency heard by the listener.
Picture the Problem We can use Equation 15-38 (s
s
fuv ±
=λ ) to find the
wavelength of the sound between the source and the listener and Equation15-41a
( ss
rr f
uvuvf
±±
= ) to find the frequency heard by the listener.
(a) Apply Equation 15-38 to find λ:
m32.1
s200m/s80m/s343
1s
s
s
s
=
−=
−=
±= −f
uvfuv
λ
(b) Apply Equation 15-41a to obtain fr:
( )
Hz261
s200m/s80m/s343
m/s343
0
1
ss
s
rr
=
−=
−±
=±±
=
−
sfuv
vfuvuvf
73 • Consider the situation described in Problem 72 from the reference frame of the source. In this frame, the listener and the air are moving toward the source at 80 m/s and the source is at rest. (a) At what speed, relative to the source, is the sound traveling in the region between the source and the listener? (b) Find the wavelength of the sound in the region between the source and the listener. (c) Find the frequency heard by the listener. Picture the Problem (a) In the reference frame of the source, the speed of sound from the source to the listener is reduced by the speed of the air. (b) We can find the wavelength of the sound in the region between the source and the listener from v = fλ. (c) Because the sound waves in the region between the source and the listener will be compressed by the motion of the listener, the frequency of the sound heard by the listener will be higher than the frequency emitted by the
source and can be calculated using ss
rr f
uvuvf
±±
= (Equation 15-41a).
Chapter 15
1590
(a) The speed of sound in the reference frame of the source is:
m/s263
m/s80m/s433wind
=
−=−= uvv'
(b) Noting that the frequency is unchanged, express the wavelength of the sound:
m32.1s200m/s263
1 === −fv'λ
(c) Apply Equation 15-41a to obtain:
( )
Hz261
s200m/s263
m/s80m/s263
0
1
sr
ss
rr
=
⎟⎟⎠
⎞⎜⎜⎝
⎛ +=
⎟⎠⎞
⎜⎝⎛
±+
=±±
=
−
fv'
uv'fuv'uv'f
74 • A sound source is moving away from the stationary listener at 80 m/s. (a) Find the wavelength of the sound waves in the region between the source and the listener. (b) Find the frequency heard by the listener. Picture the Problem We can use ( ) ss fuv ±=λ ( Equation 15-38) to find the wavelength of the sound in the region between the source and the listener
and ss
rr f
uvuvf
±±
= (Equation 15-41a) to find the frequency heard by the listener.
Because the sound waves in the region between the source and the listener will be spread out by the motion of the listener, the frequency of the sound heard by the listener will be lower than the frequency emitted by the source. (a) Because the source is moving away from the listener, use the positive sign in the numerator of Equation 15-38 to find the wavelength of the sound between the source and the listener:
m12.2
s200m/s80m/s343
1
s
s
s
s
=
+=
+=
±=
−
fuv
fuv
λ
(b) Because the listener is at rest and the source is receding, ur = 0 and the denominator of Equation 15-41a is the sum of the two speeds: ( )
Hz162
s200m/s80m/s343
m/s343
0
1
ss
ss
rr
=
+=
+±
=±±
=
−
fuv
vfuvuvf
Traveling Waves
1591
75 • The listener is moving 80 m/s from the stationary source that is in rest relative to the air. Find the frequency heard by the listener. Picture the Problem Because the listener is moving away from the source, we know that the frequency he/she will hear will be less than the frequency emitted
by the source. We can use ss
rr f
uvuvf
±±
= (Equation 15-41a), with us = 0 and the
minus sign in the numerator, to determine its value. Relate the frequency heard by the listener to that of the source:
( )
Hz153
s200m/s343
m/s80m/s343
0
1
sr
ss
rr
=
⎟⎟⎠
⎞⎜⎜⎝
⎛ −=
⎟⎠⎞
⎜⎝⎛
±−
=±±
=
−
fv
uvfuvuvf
76 •• You have made the trek to observe a Space Shuttle landing. Near the end of its descent, the ship is traveling at Mach 2.50 at an altitude of 5000 m. (a) What is the angle that the shock wave makes with the line of flight of the shuttle? (b) How far horizontally are you from the shuttle by the time you hear its shock wave, assuming the shuttle maintains both a constant heading and a constant 5000-m altitude after flying directly over your head? Picture the Problem The diagram shows the position of the shuttle at time t after it was directly over your head (located at point P) Let u represent the speed of the shuttle and v the speed of sound. We can use trigonometry to determine the angle of the shock wave as well as the location of the shuttle x when you hear the shock wave.
(a) Referring to the diagram, express θ in terms of v, u, and t: 5.2
11sin ===vuut
vtθ
Solving for θ yields: °=°=⎟
⎠⎞
⎜⎝⎛= − 6.2358.23
50.21sin 1θ
Chapter 15
1592
(b) Using the diagram, relate θ to the altitude h of the shuttle and the distance x:
xh
=θtan ⇒ θtan
hx =
Substitute numerical values and evaluate x:
km5.11tan23.58
m5000=
°=x
77 •• The SuperKamiokande neutrino detector in Japan is a water tank the size of a 14-story building. When neutrinos collide with electrons in water, most of their energy is transferred to the electrons. As a consequence, the electrons then fly off at speeds that approach c. The neutrino is counted by detecting the shock wave, called Cerenkov radiation, that is produced when the high-speed electrons travel through the water at speeds greater than the speed of light in water. If the maximum angle of the Cerenkov shock-wave cone is 48.75°, what is the speed of light in water? Picture the Problem The angle θ of the Cerenkov shock wave is related to the speed of light in water v and the speed of light in a vacuum c according to
.sin cv=θ Relate the speed of light in water v to the angle of the Cerenkov cone:
cv
=θsin ⇒ θsincv =
Substitute numerical values and evaluate v:
( )m/s10254.2
75.48sinm/s10998.28
8
×=
°×=v
78 •• You are in charge of calibrating the radar guns for a local police department. One such device emits microwaves at a frequency of 2.00 GHz. During the trials, you have it arranged so that these waves are reflected from a car moving directly away from the stationary emitter. In this situation, you detect a frequency difference (between the received microwaves and the ones sent out) of 293 Hz. Find the speed of the car. Picture the Problem Because the car is moving away from the stationary emitter at a speed ur, the frequency fr it receives will be less than the frequency emitted by the emitter. The microwaves reflected from the car, moving away from a stationary detector, will be of a still lower frequency fr′. We can use the Doppler shift equations to derive an expression for the speed of the car in terms of difference of these frequencies. Express the frequency fr received by the moving car in terms of fs, ur, and c:
sr
ss
rr 0
fc
ucfucucf ⎟
⎠⎞
⎜⎝⎛
±−
=±±
= (1)
Traveling Waves
1593
Express the frequency fr′ received by the stationary source in terms of fr, ur, and c:
rr
rs
rr 0
fc
ucfucuc'f ⎟
⎠⎞
⎜⎝⎛
±−
=±±
= (2)
Substitute equation (1) in equation (2) to eliminate fr:
. provided 21
1
rsr
s
2r
s
2r
r
cufcu
fcuf
cuc'f
<<⎟⎠⎞
⎜⎝⎛ −≈
⎟⎠⎞
⎜⎝⎛ −=⎟
⎠⎞
⎜⎝⎛ −
=
The frequency difference detected at the source is given by:
sr
sr
srs
2
21Δ
fcu
fcuf'fff
=
⎟⎠⎞
⎜⎝⎛ −−=−=
Solving for ur yields: f
fcu Δ
2 sr =
Substitute numerical values and evaluate ur: ( ) ( )
km/h1.79
hs3600
m10km1
sm0.22
Hz293GHz2.002
m/s10998.2
3
8
r
=
××=
×=u
79 •• [SSM] The Doppler effect is routinely used to measure the speed of winds in storm systems. As the manager of a weather monitoring station in the Midwest, you are using a Doppler radar system that has a frequency of 625 MHz to bounce a radar pulse off of the raindrops in a swirling thunderstorm system 50 km away. You measure the reflected radar pulse to be up-shifted in frequency by 325 Hz. Assuming the wind is headed directly toward you, how fast are the winds in the storm system moving? Hint: The radar system can only measure the component of the wind velocity along its ″line of sight.″ Picture the Problem Because the wind is moving toward the weather station (radar device), the frequency fr the raindrops receive will be greater than the frequency emitted by the radar device. The radar waves reflected from the raindrops, moving toward the stationary detector at the weather station, will be of a still higher frequency fr′. We can use the Doppler shift equations to derive an expression for the radial speed u of the wind in terms of difference of these frequencies.
Chapter 15
1594
Use Equation 15-41a to express the frequency fr received by the raindrops in terms of fs, ur, and c:
sr
ss
rr 0
fc
ucfucucf ⎟
⎠⎞
⎜⎝⎛
±+
=±±
= (1)
Express the frequency fr′ received by the stationary source at the weather station in terms of fr, ur, and c:
rr
rs
rr 0
fc
ucfucuc'f ⎟
⎠⎞
⎜⎝⎛
±+
=±±
= (2)
Substitute equation (1) in equation (2) to eliminate fr:
. provided 21
1
rsr
s
2r
s
2r
r
cufcu
fcuf
cuc'f
<<⎟⎠⎞
⎜⎝⎛ +≈
⎟⎠⎞
⎜⎝⎛ +=⎟
⎠⎞
⎜⎝⎛ +
=
The frequency difference detected at the source is:
sr
ssr
sr
2
21Δ
fcu
ffcuf'ff
=
−⎟⎠⎞
⎜⎝⎛ +=−=
Solving for ur yields: ffcu Δ
2 sr =
Substitute numerical values and evaluate ur: ( ) ( )
mi/h174
m/s4470.0mi/h1m/s 95.77
Hz253MHz2562
m/s10998.2 8
r
=
×=
×=u
80 •• A stationary destroyer is equipped with sonar that sends out 40-MHz-pulses of sound. The destroyer receives pulses back from a submarine directly below with a time delay of 80 ms at a frequency of 39.958 MHz. If the speed of sound in seawater is 1.54 km/s, (a) what is the depth of the submarine? (b) What is its vertical speed? Picture the Problem Let the depth of the submarine be represented by D and its vertical speed by u. The submarine acts as both a receiver and source. We can apply the definition of average speed to determine the depth of the submarine and use the Doppler shift equations to derive an expression for the vertical speed of the submarine in terms of the frequency difference. The frequency received is lower than the frequency of the source, so the sub is descending.
Traveling Waves
1595
(a) Using the definition of average speed, relate the depth of the submarine to the time delay between the transmitted and reflected pulses:
tvD Δ=2 ⇒ tvD Δ= 21
Substitute numerical values and evaluate D:
( )( ) m62ms80km/s1.5421 ==D
(b) Use ss
rr f
uvuvf ⎟⎟
⎠
⎞⎜⎜⎝
⎛±±
= to express
the frequency fsub received by the submarine:
0sub fv
uvf ⎟⎠⎞
⎜⎝⎛ −
= (1)
where u is the vertical speed of the submarine.
Use ss
rr f
uvuvf ⎟⎟
⎠
⎞⎜⎜⎝
⎛±±
= to express
the frequency fr′ received by the destroyer:
subr fuv
v'f ⎟⎠⎞
⎜⎝⎛
+= (2)
Substitute equation (1) in equation (2) to eliminate fsub:
0r ' fuvuvf ⎟
⎠⎞
⎜⎝⎛
+−
= ⇒ vffffu '
'
r0
r0
+−
=
Substitute numerical values and evaluate u:
( ) m/s81.0km/s 54.1MHz 958.39MHz 000.40MHz 958.39MHz 000.40
=⎟⎠⎞
⎜⎝⎛
+−
=u
and so, because u is positive, the sub is descending. 81 •• A police radar unit transmits microwaves of frequency 3.00 × 1010 Hz, and their speed in air is 3.00 × 108 m/s. Suppose a car is receding from the stationary police car at a speed of 140 km/h. (a) What is the frequency difference between the transmitted signal and the signal received from the receding car? (b) Suppose the police car is, instead, moving at a speed of 60 km/h in the same direction as the other vehicle. What is the difference in frequency between the emitted and the reflected signals? Picture the Problem The radar wave strikes the speeding car at frequency fr .This frequency is less than fs because the car is moving away from the source. The frequency shift is given by Equation 15-42 (the low-speed, relative to light, approximation). The car then acts as a moving source emitting waves of frequency fr. The police car detects waves of frequency fr′ < fr because the source (the speeding car) is moving away from the police car. The total frequency shift
Chapter 15
1596
is the sum of the two frequency shifts. (a) Express the frequency difference Δf as the sum of the frequency difference sr1Δ fff −= and the frequency difference rr2Δ f'ff −= :
21 ΔΔΔ fff += (1)
Using Equation 15-42, substitute for the frequency differences in equation (1):
( )rsrsΔ ffcuf
cuf
cuf +−=−−= (2)
where rs uuu ±= is the speed of the source relative to the receiver.
Apply Equation 15-42 to 1Δf to obtain:
cu
fff
ff
−=−
=s
sr
s
1Δ
where we’ve used the minus sign because we know the frequency difference is a downshift.
Solving for fr yields: sr 1 f
cuf ⎟
⎠⎞
⎜⎝⎛ −=
Substitute for fr in equation (2) and simplify to obtain:
s
ss
2
1Δ
fcu
cu
fcuf
cuf
⎟⎠⎞
⎜⎝⎛ −−=
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛ −+−=
Because u/c is negligible compared to 2: c
uff s2Δ −≈
Substitute numerical values and evaluate Δf:
( ) kHz 78.7m/s 1000.3
s3600h1
hkm140
Hz103.002Δ 810 −=
×
⎟⎟⎠
⎞⎜⎜⎝
⎛×
×−≈f
Traveling Waves
1597
(b) Use the result derived in (a) with u equal to the difference in the speeds of the car and the police cruiser to obtain:
( ) kHz .44m/s 1000.3
s3600h1
hkm 60
hkm140
Hz103.002Δ 810 −=
×
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛ −
×−≈f
82 •• In modern medicine, the Doppler effect is routinely used to measure the rate and direction of blood flow in arteries and veins. High frequency ″ultrasound″ (sound at frequencies above the human hearing range) is typically employed. Suppose you are in charge of measuring the blood flow in a vein (located in the lower leg of an older patient) that returns blood upward to the heart. Her varicose veins indicate that perhaps the one-way valves in the vein are not working properly and that the blood is ″pooling″ in the veins and perhaps even that the blood flow is backward toward her feet. Employing sound with a frequency of 50.0 kHz, you point the sound source from above her thigh region down towards her feet and measure the sound reflected from that vein area to be lower than 50.0 kHz. (a) Was your diagnosis of the valve condition correct? If so, explain. (b) Estimate the instrument’s frequency difference capability to enable you to measure speeds down to 6.00 cm/s. Take the speed of sound in flesh to be the same as that in water, 1500 m/s. Picture the Problem (a) Whether your diagnosis was correct depends on whether the signal reflected from the blood is upshifted or downshifted. (b) Applying the Doppler shift equations with the source stationary and the receiver moving initially and then a second time with the source moving and the receiver stationary will allow us to estimate the instrument’s frequency difference capability. (a) Because the received sound frequency is less than the frequency that was sent out, the blood it reflected from must have been moving away from the source, or toward the feet of the patient. The blood is flowing the wrong way and your diagnosis is correct. (b) The blood receives a frequency that is downshifted according to:
sr
sr
ss
rr
1
0
fvu
fv
uvfuvuvf
⎟⎠⎞
⎜⎝⎛ −=
⎟⎠⎞
⎜⎝⎛
±−
=⎟⎟⎠
⎞⎜⎜⎝
⎛±±
= (1)
Chapter 15
1598
The frequency given by equation (1) is the frequency emitted by the moving blood back toward the receiver. This results in a second downshift:
''
'''
fvuf
vu
fuv
vfuvuvf
ss
s
1s
ss
ss
rr
11
0
⎟⎠⎞
⎜⎝⎛ −≈⎟
⎠⎞
⎜⎝⎛ +=
⎟⎟⎠
⎞⎜⎜⎝
⎛+±
=⎟⎟⎠
⎞⎜⎜⎝
⎛±±
=
− (2)
The source frequency in equation (2) is the received frequency given by equation (1). Note that the receiver and emitter speeds are the same … the speed of the blood. Let this speed be u to obtain:
ssr 2111 fvuf
vu
vuf ' ⎟
⎠⎞
⎜⎝⎛ −≈⎟
⎠⎞
⎜⎝⎛ −⎟
⎠⎞
⎜⎝⎛ −≈
Express the magnitude of the difference in frequencies:
s
ssrs
2
21Δ
fvu
fvuffff '
=
⎟⎠⎞
⎜⎝⎛ −−≈−=
Substitute numerical values and evaluate Δf:
( )
Hz .004
kHz 0.50m/s 1500
cm/s .0062Δ
=
⎟⎠⎞
⎜⎝⎛≈f
83 •• [SSM] A sound source of frequency f0 moves with speed us relative to still air toward a receiver who is moving with speed ur relative to still air away from the source. (a) Write an expression for the received frequency f′. (b) Use the result that (1 – x)–1 ≈ 1 + x to show that if both us and ur are small compared to v,
then the received frequency is approximately srel1' fv
uf ⎟⎠⎞
⎜⎝⎛ += , where urel = us – ur
is the velocity of the source relative to the receiver. Picture the Problem The received and transmitted frequencies are related
through ss
rr f
uvuvf
±±
= (Equation 15-41a), where the variables have the meanings
given in the problem statement. Because the source and receiver are moving in the same direction, we use the minus signs in both the numerator and denominator.
Traveling Waves
1599
(a) Relate the received frequency fr to the frequency fs of the source:
s
1sr
ss
r
ss
rr
11
1
1
fvu
vu
f
vuvu
fuvuvf
−
⎟⎠⎞
⎜⎝⎛ −⎟
⎠⎞
⎜⎝⎛ −=
−
−=
±±
=
(b) Expand ( ) 1
s1 −− vu binomially and discard the higher-order terms:
vu
vu s
1s 11 +≈⎟
⎠⎞
⎜⎝⎛ −
−
Substitute to obtain:
srs
ssrrs
ssr
r
1
1
11
fv
uu
fvu
vu
vu
vu
fvu
vuf
⎟⎠⎞
⎜⎝⎛ −
+≈
⎥⎦
⎤⎢⎣
⎡⎟⎠⎞
⎜⎝⎛
⎟⎠⎞
⎜⎝⎛−−+=
⎟⎠⎞
⎜⎝⎛ +⎟
⎠⎞
⎜⎝⎛ −=
because both us and ur are small compared to v.
Because urel = us − ur s
relr 1 f
vuf ' ⎟
⎠⎞
⎜⎝⎛ +≈
84 ••• To study the Doppler shift on your own, you take an electronic tone generating device that is set to a frequency of middle C (262Hz) to a campus wishing well known as ″The Abyss. ″ When you hold the device at arm’s length (1.00 m), you measure its intensity level to be 80.0 dB. You then drop the tuner down the hole, listening to its sound as it falls. (a) After the tuner has fallen for 5.50 s, what frequency do you hear? (b) Estimate the time at which you can no longer hear the tuner. Picture the Problem (a) As the tuner falls, its speed increases and so the frequency you hear is Doppler shifted. Our concern, however, is with the frequency you hear 5.50 s after you’ve dropped the tuner. The sound that you hear at this time was emitted sometime before the tuner had fallen for 5.50 s. Hence we must answer the question ″At what time was the sound emitted that you heard 5.50 s after dropping the tuner?″ (b) We’ll estimate the minimum intensity of the sound from the tuner when it can be heard at the top of the well to be 30.0 dB. Then we can use the intensity level decrease of 50.0 dB to find the depth of the tuner when it can no longer be heard. The time at which you can no longer hear the tuner is the sum of the time it took the tuner to fall to the depth at which you
Chapter 15
1600
can no longer hear it and the time it takes the sound to travel back to your ears. (a) Apply Equation 15-41a to express the frequency you’ll hear after 5.50 s:
sfall
ss
rr f
vvvf
uvuvf
+=
±±
= (1)
Relate the elapsed time of 5.50 s to the time required for the tuner to fall and the time for the sound to return to you:
returnfalltot ΔΔΔ ttt += (2)
Use a constant-acceleration equation to relate the time-of-fall to the fall distance:
( )2fall2
1 ΔΔ tgy = ⇒g
yt 2ΔΔ fall =
The return time depends on how far the tuner has fallen and on the speed of sound in air:
vyt ΔΔ return = ⇒ returnΔΔ tvy =
Substituting for Δy in the expression for Δtfall yields: g
tvt returnfall
Δ2Δ =
Square both sides of the equation, use equation (2) to substitute for Δtreturn, and write the result explicitly as a quadratic equation to obtain:
( ) ( ) 0Δ2Δ2Δ totfall2
fall =−+ tgvt
gvt
Substitute numerical values to obtain:
( ) ( ) ( ) ( )( ) 0m/s81.9
s 50.5m/s 3432Δm/s81.9m/s 3432Δ 2fall2
2fall =−+ tt
or ( ) ( )( ) 0s 6.384Δs 93.69Δ 2
fall2
fall =−+ tt
Use your graphing calculator or the quadratic formula to solve this equation for its positive root:
s 124.5Δ fall =t
Because fallfall Δtgv = , equation (1) becomes:
sfall
r Δf
tgvvf
+=
Traveling Waves
1601
Substitute numerical values and evaluate fr:
( )( ) ( ) Hz 229Hz 262s 124.5m/s 81.9m/s 343
m/s 3432r =
+=f
(b) The sound will reach your ear when: v
ygy
ttt
ff
returnfall
2
ΔΔΔ
+=
+=
(3)
where yf is the depth of the tuner when it can no longer be heard at the top of the well.
Express the initial and final intensity levels to the change in intensity level that corresponds to no longer being able to hear the tuner:
βββ Δif += (4)
The initial and final intensity levels are given by:
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
02i
ii 4
logdB 10Iy
Pπ
β
and
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛=
02f
ff 4
logdB 10Iy
Pπ
β
Substitute in equation (4) to obtain:
( ) ( ) βππ
Δ4
logdB 104
logdB 100
2i
i
02f
f +⎟⎟⎠
⎞⎜⎜⎝
⎛=⎟⎟
⎠
⎞⎜⎜⎝
⎛Iy
PIy
P
or
( ) ( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛−⎟⎟
⎠
⎞⎜⎜⎝
⎛=
02i
i
02f
f
4logdB 10
4logdB 10Δ
IyP
IyP
ππβ
Assuming a decrease in the decibel level of 50.0 dB and simplifying yields:
( ) ( )2
f
i
02i
i
02f
f
logdB 10
4
4logdB 10dB 50 ⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎟⎟⎟⎟
⎠
⎞
⎜⎜⎜⎜
⎝
⎛
=−yy
IyP
IyP
π
π
Chapter 15
1602
Simplify further to obtain:
2
f
ilog5 ⎟⎟⎠
⎞⎜⎜⎝
⎛=−
yy or i
5.2f 10 yy =
Substituting for yf in equation (3) yields: v
yg
yt i5.2
i5.2 10102Δ +
×=
Substitute numerical values and evaluate Δt:
( ) ( )
s 0.9m/s 343
m 0.110m/s 81.9
m 0.1102Δ5.2
2
5.2
≈
+×
=t
85 •• You are in a hot-air balloon carried along by a 36-km/h wind and have a sound source with you that emits a sound of 800 Hz as it approaches a tall building. (a) What is the frequency of the sound heard by an observer at the window of this building? (b) What is the frequency of the reflected sound heard by you? Picture the Problem The simplest way to approach this problem is to transform to a reference frame in which the balloon is at rest. In that reference frame, the speed of sound is v = 343 m/s, and ur = 36 km/h = 10 m/s. Then, we can use the equations for a moving receiver and a moving source to find the frequencies heard at the window and on the balloon. (a) Use Equation 15-41a to express the received frequency in terms of the frequency of the source:
sr
s
r
ss
r
ss
rr
1
01
1
1
1
fvu
f
v
vu
f
vuvu
fuvuvf
⎟⎠⎞
⎜⎝⎛ +=
±
+=
±
±=
±±
=
Substitute numerical values and evaluate fr:
( )
kHz82.0
Hz823Hz800m/s343
m/s101r
=
=⎟⎟⎠
⎞⎜⎜⎝
⎛+=f
(b) Treating the tall building as a moving source, express the frequency of the reflected sound heard by a person riding in the balloon:
Traveling Waves
1603
rs
rs
rs
r
rs
rr
1
1
1
01
1
1f
vu
f
vuvf
vuvu
fuvuv'f
⎟⎟⎟⎟
⎠
⎞
⎜⎜⎜⎜
⎝
⎛
−=
−
±=
±
±=
±±
=
Substitute numerical values and evaluate fr′: ( )
kHz0.85
Hz823
m/s343m/s101
1r
=
⎟⎟⎟⎟
⎠
⎞
⎜⎜⎜⎜
⎝
⎛
−='f
86 •• A car is approaching a reflecting wall. A stationary observer behind the car hears a sound of frequency 745 Hz from the car horn and a sound of frequency 863 Hz from the wall. (a) How fast is the car traveling? (b) What is the frequency of the car horn? (c) What frequency does the car driver hear reflected from the wall? Picture the Problem We can relate the frequencies fr and fr′ heard by the stationary observer behind the car to the speed of the car ur and the frequency of the car’s horn fs. Dividing these equations will eliminate the frequency of the car’s horn and allow us to solve for the speed of the car. We can then substitute to find the frequency of the car’s horn. We can find the frequency heard by the driver as a moving receiver by relating this frequency to the frequency reflected from the wall. (a) Use Equation 15-41a to relate the frequency heard by the observer directly from the car’s horn to the speed of the car:
ss
ss
ss
r
ss
rr
1
1
1
01
1
1
f
vu
f
vuvf
vuvu
fuvuvf
+=
+
±=
±
±=
±±
=
(1)
Relate the frequency reflected from the wall to the speed of the car:
ss
ss
ss
rr
1
1
1
01
f
vu
f
vuvf
uvuv'f
−=
−
±=
±±
=
(2)
Chapter 15
1604
Divide equation (2) by equation (1) to obtain:
vuvu
f'f
s
s
r
r
1
1
−
+= ⇒ v
'f'ff'furr
rr
+−
=
Substitute numerical values and evaluate us:
( )
km/h6.90
hs3600
m10km1
sm17.25
m/s343Hz745Hz863Hz745Hz863
3
s
=
××=
+−
=u
(b) Solve equation (1) for fs to obtain: r
rs 1 f
vuf ⎟
⎠⎞
⎜⎝⎛ +=
Substitute numerical values and evaluate fs:
( )
Hz800
Hz745m/s343m/s25.171s
=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=f
(c) The driver is a moving receiver and so we can relate the frequency heard by the driver to the frequency reflected by the wall (the frequency heard by the stationary observer):
'fvuf r
rdriver 1 ⎟
⎠⎞
⎜⎝⎛ +=
Substitute numerical values and evaluate fdriver:
( )
Hz926
H863m/s343m/s25.171driver
=
⎟⎟⎠
⎞⎜⎜⎝
⎛+= zf
87 •• The driver of a car traveling at 100 km/h toward a vertical wall briefly sounds the horn. Exactly 1.00 s later she hears the echo and notes that its frequency is 840 Hz. How far from the wall was the car when the driver sounded the horn and what is the frequency of the horn? Picture the Problem Let t = 0 when the driver sounds her horn and let the distance to the wall at that instant be d. The received and transmitted frequencies
are related through ss
rr f
uvuvf
±±
= (Equation 15-41a). Solving this equation for fs
will allow us to determine the frequency of the car horn. We can use the total distance the sound travels (car-to-wall plus wall-back to-car … now closer to the
Traveling Waves
1605
wall) to determine the distance to the wall when the horn was briefly sounded. Use Equation 15-41a to relate the frequency heard by the driver to her speed and to the frequency of her horn:
ss
r
ss
r
ss
rr
1
1
1
1f
vuvu
f
vuvu
fuvuvf
−
+=
±
±=
±±
=
Solving for fs yields:
rr
s
s
1
1f
vuvu
f+
−=
Substitute numerical values and evaluate fs:
( ) ( ) Hz 714Hz840
m/s343m/s78.271
m/s343m/s78.271
Hz840
m/s343s3600
h1h
km1001
m/s343s3600
h1h
km1001
s =+
−=
×+
×−
=f
Relate the distance d to the wall at t = 0 to the distance she travels in time Δt = 1 s, her speed us, and the speed of sound v:
( ) tvtudd ΔΔs =−+ ⇒ ( ) tvud Δs21 +=
Substitute numerical values and evaluate d:
( )( )m185
s1.00m/s343m/s27.7821
=
+=d
88 •• You are on a transatlantic flight traveling due west at 800 km/h. An experimental plane flying at Mach 1.6 and 3.0 km to the north of your plane is also on an east-to-west course. What is the distance between the two planes when you hear the sonic boom from the experimental plane? Picture the Problem You’ll hear the sonic boom when the surface of its cone reaches your plane. In the following diagram, the experimental plane is at C and your plane is at P. The distance h = 3.0 km. The distance between the planes when you hear the sonic boom is d. We can use trigonometry to determine the angle of the shock wave as well as the separation of the planes when you hear the sonic boom.
Chapter 15
1606
Using the Pythagorean theorem, relate the separation of the planes d, to the distance h and the angle θ :
θ2222 cosdhd += ⇒θ2cos1
1−
= hd
Express θ in terms of v, u, and t: 6.1
11sin ===vuut
vtθ
so
°=⎟⎠⎞
⎜⎝⎛= − 7.38
6.11sin 1θ
Substitute numerical values and evaluate d: ( ) km8.4
7.38cos11km0.3 2 =
°−=d
89 ••• The Hubble space telescope has been used to determine the existence of planets orbiting around distant stars. The planet orbiting the star will cause the star to ″wobble″ with the same period as the planet’s orbit. Because of wobble, light from the star will be Doppler-shifted up and down periodically. Estimate the maximum and minimum wavelengths of light of nominal wavelength 500 nm emitted by the Sun that is Doppler-shifted by the motion of the Sun due to the planet Jupiter. Picture the Problem The Sun and Jupiter orbit about their effective mass located at their common center of mass. We can apply Newton’s 2nd law to the Sun to obtain an expression for its orbital speed about the Sun-Jupiter center of mass and then use this speed in the Doppler shift equation to estimate the maximum and minimum wavelengths resulting from the Jupiter-induced motion of the Sun. Letting v be the orbital speed of the sun about the center of mass of the Sun-Jupiter system, express the Doppler shift of the light due to this motion when the Sun is approaching Earth:
cvcv
c
cvcv
f'
cf'−
+=
−
+==
1
1
1
1
λλ
Traveling Waves
1607
Solving for λ′ and simplifying yields:
2121
1
11
111
1
−
−
⎟⎠⎞
⎜⎝⎛ +⎟
⎠⎞
⎜⎝⎛ −=
⎟⎠⎞
⎜⎝⎛ +⎟
⎠⎞
⎜⎝⎛ −=
+
−=
cv
cv
cv
cv
cvcv
'
λ
λλλ
Because v << c, we can expand
21
1 ⎟⎠⎞
⎜⎝⎛ −
cv and
21
1−
⎟⎠⎞
⎜⎝⎛ +
cv
binomially to obtain:
cv
cv
211
21
−≈⎟⎠⎞
⎜⎝⎛ −
and
cv
cv
211
21
−≈⎟⎠⎞
⎜⎝⎛ +
−
Substitute for 21
1 ⎟⎠⎞
⎜⎝⎛ −
cv and
21
1−
⎟⎠⎞
⎜⎝⎛ +
cv to obtain:
cv
cv
cvcv
−≈⎟⎠⎞
⎜⎝⎛ −=
+
−1
21
1
1 2
When the Sun is receding from Earth: c
vc
v
cvcv
+≈⎟⎠⎞
⎜⎝⎛ +=
−
+1
21
1
1 2
Hence the motion of the Sun will give an observed Doppler shift of: ⎟
⎠⎞
⎜⎝⎛ ±≈
cv' 1λλ (1)
Apply Newton’s 2nd law to the Sun:
cm
2
S2cm
effS
rvM
rMGM
= ⇒cm
eff
rGMv =
Measured from the center of the Sun, the distance to the center of mass of the Sun-Jupiter system is:
( )Js
JJ-s
Js
JJ-sScm
0MM
MrMM
MrMr+
=++
=
The effective mass is related to the masses of the Sun and Jupiter according to:
Jseff
111MMM
+= ⇒Js
Jseff MM
MMM+
=
Chapter 15
1608
Substitute for Meff and rcm to obtain:
J-s
s
Js
JJ-s
Js
Js
rGM
MMMr
MMMMG
v =
+
+=
Using m1078.7 11
J-s ×=r as the mean orbital radius of Jupiter, substitute numerical values and evaluate v:
( )( ) m/s10306.1m1078.7
kg1099.1kg/mN10673.6 411
302211
×=×
×⋅×=
−
v
Substitute numerical values in equation (1) to obtain: ( )
( )( )5
8
4
1036.41nm500
m/s10998.2m/s10306.11nm500'
−×±=
⎟⎟⎠
⎞⎜⎜⎝
⎛××
±≈λ
The maximum and minimum wavelengths are:
( )( )5max 1036.41nm500 −×+=λ
and ( )( )5
min 1036.41nm500 −×−=λ
General Problems 90 • At time t = 0, the shape of a wave pulse on a string is given by the function ( ) ( )( )223 m 2.00/m 120.00, xxy += , where x is in meters. (a) Sketch y(x, 0) versus x. (b) Give the wave function y(x,t) at a general time t if the pulse is moving in the +x direction with a speed of 10.0 m/s and if the pulse is moving in the −x direction with a speed of 10.0 m/s. Picture the Problem The equation of a wave traveling in the positive x direction is of the form ( ) )( vtxfx,ty −= and that of a wave traveling in the negative x direction is ( ) )( vtxfx,ty += .
Traveling Waves
1609
(a) The pulse at t = 0 shown below was plotted using a spreadsheet program:
0.000
0.005
0.010
0.015
0.020
0.025
0.030
0.035
-6 -4 -2 0 2 4 6
x (m)
y(x
,0) (
m)
(b) If the pulse is moving in the +x direction, the wave function must be of the form:
( ) ( )[ ]txfvtxfx,ty m/s0.10)( −=−= because v = 10.0 m/s
Replace x with ( )tx m/s0.10− to obtain: ( )
( ) ( )[ ]22
3
m/s0.10m00.2m120.0
txx,ty
−+=
If the pulse is moving in the −x direction, the wave function must be of the form:
( ) ( )[ ]txfvtxfx,ty m/s0.10)( +=+= because v = 10.0 m/s
Replace x with ( )tx m/s0.10+ to obtain: ( )
( ) ( )[ ]22
3
m/s0.10m00.2m120.0,
txtxy
++=
91 • [SSM] A whistle that has a frequency of 500 Hz moves in a circle of radius 1.00 m at 3.00 rev/s. What are the maximum and minimum frequencies heard by a stationary listener in the plane of the circle and 5.00 m away from its center?
Chapter 15
1610
Picture the Problem The diagram depicts the whistle traveling in a circular path of radius r = 1.00 m. The stationary listener will hear the maximum frequency when the whistle is at point 1 and the minimum frequency when it is at point 2. These maximum and minimum frequencies are determined by f0 and the tangential speed us = 2π r/T. We can relate the frequencies heard at point P to the speed of the approaching whistle at point 1 and the speed of the receding whistle at point 2.
su
m 00.1=r
m 00.5
1 2
P
su
Relate the frequency heard at point P to the speed of the approaching whistle at point 1:
ss
max
1
1 f
vu
f−
=
Because ωru =s : smax
1
1 f
vr
fω
−=
Substitute numerical values and evaluate fmax:
( )( ) Hz529Hz500
m/s343rev
rad2s
rev3.00m00.11
1max =
⎟⎠⎞
⎜⎝⎛ ×
−
=π
f
Relate the frequency heard at point P to the speed of the receding whistle at point 2:
ss
min
1
1 f
vu
f+
=
Substitute numerical values and evaluate fmin:
( )( ) Hz474Hz500
m/s343rev
rad2s
rev3.00m00.11
1min =
⎟⎠⎞
⎜⎝⎛ ×
+
=π
f
Traveling Waves
1611
92 • Ocean waves move toward the beach with a speed of 8.90 m/s and a crest-to-crest separation of 15.0 m. You are in a small boat anchored off shore. (a) At what frequency do the wave crests reach you boat? (b) You now lift anchor and head out to sea at a speed of 15.0 m/s. At what frequency do the wave crests reach your boat now? Picture the Problem (a) The crest-to-crest separation of the waves is their wavelength. We can find the frequency of the waves from v = fλ. (b) When you lift anchor and head out to sea you’ll become a moving receiver and we can
apply ss
rr f
uvuvf
±±
= to calculate the frequency you’ll observe.
(a) The frequency of the ocean waves is the ratio of their speed to their wavelength:
Hz0.593m15.0
m/s8.900 ===
λvf
(b) Express the frequency of the waves in terms of their speed and the speed of a moving receiver:
sr
sr
ss
rr 1 f
vuf
vuvf
uvuvf ⎟
⎠⎞
⎜⎝⎛ +=
+=
±±
=
Substitute numerical values and evaluate fr:
( )
Hz1.59
Hz0.593m/s8.90m/s15.01r
=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=f
93 •• A 12.0-m-long wire that has an 85.0-g mass is stretched under a tension of 180 N. A pulse is generated at the left end of the wire, and 25.0 ms later a second pulse is generated at the right end of the wire. Where do the pulses first meet? Picture the Problem Let t be the time of travel of the left-hand pulse and the subscripts L and R refer to the pulse coming from the left and right, respectively. Because the pulse traveling from the right starts later than the pulse from the left, its travel time is t − Δt, where Δt = 25.0 ms. Both pulses travel at the same speed and the sum of the distances they travel is 12.0 m. Express the total distance the two pulses travel:
( )ttvvtddd Δ−+=+= RL
Solve for vt to obtain:
( )tvdvt Δ+= 21
Chapter 15
1612
The speed of the pulse is given by: Lm
FFv TT ==μ
Substituting for v yields:
⎟⎟⎠
⎞⎜⎜⎝
⎛+= t
LmFdvt ΔT
21
Substitute numerical values and evaluate vt:
( )( ) ( ) m99.7s1025.0kg0.085
m12.0N180m12.0 321 =⎥
⎦
⎤⎢⎣
⎡×+= −vt
from the left end of the wire. 94 •• You are parked on the shoulder of a highway. Find the speed of a car in which the tone of the car’s horn drops by 10 percent as it passes you. (In other words, the total drop in frequency between the ″approach″ value and the ″recession″ value is 10%.) Picture the Problem Let the frequency of the car’s horn be fs, the frequency you hear as the car approaches be fr, and the frequency you hear as the car recedes be
fr′. We can use ss
rr f
uvuvf
±±
= to express the frequencies heard as the car
approaches and recedes and then use these frequencies to express the fractional change in frequency as the car passes you. Express the fractional change in frequency as the car passes you:
10.0Δ
r
=ff
Relate the frequency heard as the car approaches to the speed of the car:
ss
ss
ss
rr
1
10 f
vu
fuv
vfuvuvf
−=
−±
=±±
=
Express the frequency heard as the car recedes in terms of the speed of the car:
ss
r
1
1 f
vu
'f+
=
Traveling Waves
1613
Divide the second of these frequency equations by the first to obtain:
vuvu
f'f
s
s
r
r
1
1
+
−=
and
10.01
11Δ
s
s
rr
r
r
r =+
−−==−
vuvu
ff
f'f
ff
Solving for us yields: vu
9.110.0
s =
Substitute numerical values and evaluate us:
( )
km/h65h
s360010km1
sm05.18
m/s3439.110.0
3
s
=
××=
=u
95 •• [SSM] A loudspeaker driver 20.0 cm in diameter is vibrating at 800 Hz with an amplitude of 0.0250 mm. Assuming that the air molecules in the vicinity have the same amplitude of vibration, find (a) the pressure amplitude immediately in front of the driver, (b) the sound intensity, and (c) the acoustic power being radiated by the front surface of the driver. Picture the Problem (a) and (b) The pressure amplitude can be calculated directly from ,00 vsp ρω= and the intensity from .2
02
21 vsI ρω= (c) The power
radiated is the intensity times the area of the driver. (a) Relate the pressure amplitude to the displacement amplitude, angular frequency, wave velocity, and air density:
00 vsp ρω=
Substitute numerical values and evaluate p0:
( ) ( )[ ]( )( )
2
3
130
N/m6.55
m100.0250m/s343
s8002kg/m1.29
=
××
=−
−πp
(b) Relate the intensity to these same quantities:
vsI 20
221 ρω=
Chapter 15
1614
Substitute numerical values and evaluate I:
( ) ( )[ ]( ) ( )
22
23
21321
W/m49.3W/m494.3
m/s343m100.0250
s8002kg/m1.29
==
××
=−
−πI
(c) Express the power in terms of the intensity and the area of the driver:
IrIAP 2π==
Substitute numerical values and evaluate P:
( ) ( )W110.0
W/m3.494m100.0 22
=
= πP
96 •• A plane, harmonic, sound wave in air has an amplitude of 1.00 μm and has an intensity of 10.0 mW/m2. What is the frequency of the wave? Picture the Problem The frequency of the wave is related to the density of the air, displacement amplitude, and velocity by .2
02
21 vsI ρω=
Relate the intensity of the wave to the density of the air, displacement amplitude, velocity, and angular frequency:
vsI 20
221 ρω= ⇒
vI
s ρω 21
0
=
Because fπω 2= :
vI
sf
ρπ2
21
0
=
Substitute numerical values and evaluate f:
( )( )
( )( ) kHz07.1m/s343kg/m1.29
W/m1000.12m1000.12
13
22
6 =×
×=
−
−πf
97 •• Water flows at 7.0 m/s in a pipe of radius 5.0 cm. A plate with area equal to the cross-sectional area of the pipe is suddenly inserted to stop the flow. Find the force exerted on the plate. Take the speed of sound in water to be 1.4 km/s. Hint: When the plate is inserted, a pressure wave propagates through the water at the speed of sound vs. The mass of water brought to a stop in time Δt is the water in a length of pipe equal to vsΔt. Picture the Problem The force exerted on the plate is due to the change in momentum of the water. We can use Newton’s 2nd law in the form F = Δp/Δt to relate F to the mass of water in a length of pipe equal to vsΔt and to the speed of
Traveling Waves
1615
the water. This mass of water, in turn, is given by the product of its density and the volume of water in a length of pipe equal to vsΔt. Relate the force exerted on the plate to the change in momentum of the water:
tmv
tpF
ΔΔ
=ΔΔ
= w
Express Δm in terms of the mass of water in a length of pipe equal to vsΔt:
tAvVm Δ=Δ=Δ sρρ
Substitute for Δm to obtain:
ws AvvF ρ=
Substitute numerical values and evaluate F:
( )( ) ( )[ ]( ) kN77m/s7.0m0.050km/s1.4kg/m011.00 233 =×= πF 98 •• A high-speed flash photography setup to capture a picture of a bullet exploding a soap bubble is shown in Figure 15-33. The shock wave from the bullet is to be detected by a microphone that will trigger the flash. The microphone is placed on a track that is parallel to, and 0.350 m below, the path of the bullet. The track is used to adjust the position of the microphone. If the bullet is traveling at 1.25 times the speed of sound, and the distance between the lab bench and the track is 0.350 m, how far back from the soap bubble must the microphone be set to trigger the flash? (Assume that the flash itself is instantaneous once the microphone is triggered.) Picture the Problem Let d be the horizontal distance from the soap bubble to the position of the microphone. The angle θ of the shock wave is related to the speed of sound in air u and the speed of the bullet c according to .sin vu=θ We can determine θ from the given information and then use this angle to find d. Express d in terms of the angle of the shock wave and the distance from the soap bubble to the laboratory bench:
θtanm350.0
=d (1)
Relate the speed of the bullet to the angle of the shock-wave cone:
vu
=θsin ⇒ ⎟⎠⎞
⎜⎝⎛= −
vu1sinθ
Chapter 15
1616
Substitute for θ in equation (1) to obtain:
⎥⎦
⎤⎢⎣
⎡⎟⎠⎞
⎜⎝⎛
=−
vu
d1sintan
m350.0
Substitute numerical values and evaluate d:
cm3.26
25.1sintan
m350.01
=
⎥⎦
⎤⎢⎣
⎡⎟⎠⎞
⎜⎝⎛
=−
uu
d
99 •• A column of precision marchers keeps in step by listening to the band positioned at the head of the column. The beat of the music is for 100 paces/min. A television camera shows that only the marchers at the front and the rear of the column are actually in step. The marchers in the middle section are striding forward with the left foot when those at the front and rear are striding forward with the right foot. The marchers are so well trained, however, that they are all certain that they are in proper step with the music. How long is the column? Picture the Problem The source of the problem is that it takes a finite time for the sound to travel from the front of the line of marchers to the back. We can use the given data to determine the time required for the beat to reach the marchers in the back of the column and then use this time and the speed of sound to find the length of the column. Express the length of the column in terms of the speed of sound and the time required for the beat to travel the length of the column:
tvL Δ=
Calculate the time for the sound to travel the length of the column:
s600.0min100
1Δ ==t
Substitute numerical values and evaluate L:
( )( ) m206s0.600m/s343 ==L
100 •• A bat flying toward a stationary obstacle at 12.0 m/s emits brief, high-frequency sound pulses at a repetition frequency of 80.0 Hz. What is the interval between the arrival times of the reflected pulses heard by the bat? Picture the Problem The interval between the arrival times of the reflected pulses heard by the bat is the reciprocal of the frequency of the reflected pulses.
We can use ss
rr f
uvuvf
±±
= to relate the frequency of the reflected pulses to the
speed of the bat and the frequency it emits.
Traveling Waves
1617
Relate the interval between the arrival times of the echo pulses heard by the bat to frequency of the reflected pulses:
r
1f
t =Δ
Relate the frequency of the pulses received by the bat to its speed and the frequency it emits:
ss
r
ss
rs
s
rr
1
1f
vuvu
fuvuvf
uvuvf
−
+=
−+
=±±
=
Substitute for fr to obtain:
sr
s
1
1Δ
fvu
vu
t⎟⎠⎞
⎜⎝⎛ +
−=
Substitute numerical values and evaluate Δt:
( )ms7.11
s80.0m/s343m/s12.01
m/s343m/s12.01
Δ1
=
⎟⎟⎠
⎞⎜⎜⎝
⎛+
−=
−
t
101 •• Laser ranging to the moon is done routinely to accurately determine the Earth–moon distance. However, to determine the distance accurately, corrections must be made for the average speed of light in Earth’s atmosphere, which is 99.997 percent of the speed of light in vacuum. Assuming that Earth’s atmosphere is 8.00 km high, estimate the length of the correction. Picture the Problem Let d be the distance to the moon, h be the height of Earth's atmosphere, and v be the average speed of light in Earth’s atmosphere. We can express d ′, the distance measured when Earth’s atmosphere is ignored, in terms of the time for a pulse of light to make a round-trip from Earth to the moon and solve this equation for the length of correction d ′ − d. Express the roundtrip time for a pulse of light to reach the moon and return: c
hdvh
ttt
−+=
+=
22
atmosphere searth' ofout atmosphere searth'
Express the "measured" distance d ′ when we do not account for the atmosphere: hdh
vc
chd
vhcctd'
−+=
⎟⎠⎞
⎜⎝⎛ −
+== 2221
21
Chapter 15
1618
Solve for the length of correction d ′ − d: ⎟
⎠⎞
⎜⎝⎛ −=− 1
vchdd'
Substitute numerical values and evaluate d ′ − d:
( )
m2.0
199997.0
km00.8
≈
⎟⎠⎞
⎜⎝⎛ −=−
ccdd'
Remarks: This is larger than the accuracy of the measurements, which is about 3 to 4 cm. 102 •• A tuning fork attached to a taut string generates transverse waves. The vibration of the fork is perpendicular to the string. Its frequency is 400 Hz and the amplitude of its oscillation is 0.50 mm. The string has a linear mass density of 0.010 kg/m and is under a tension of 1.0 kN. Assume that there are no waves reflected at the far end of the string. (a) Find the period and frequency of waves on the string. (b) What is the speed of the waves? (c) What are the wavelength and wave number? (d) Write a suitable wave function for the waves on the string. (e) Calculate the maximum speed and acceleration of a point on the string. (f) At what minimum average rate must energy be supplied to the fork to keep it oscillating at a steady amplitude? Picture the Problem (a) The frequency of the waves on the string is the same as the frequency of the tuning fork and their period is the reciprocal of the frequency. (b) We can find the speed of the waves from the tension in the string and its linear density. (c) The wavelength can be determined from the frequency and the speed of the waves and the wave number from its definition. (d) The general form of the wave function for waves on a string is ( ) ( )tkxAx,ty ω±= sin , so, once we know k and ω, because A is given, we can write a suitable wave function for the waves on this string. (e) The maximum speed and acceleration of a point on the string can be found from the angular frequency and amplitude of the waves. (f) Finally, we can use vAP 22
21
av μω= to find the minimum average rate at which energy must be supplied to the tuning fork to keep it oscillating with a steady amplitude. (a) The frequency of the waves on the string is the same as the frequency of the tuning fork:
Hz400=f
The period of the waves on the wire is the reciprocal of their frequency:
ms2.50s400
111 === −f
T
Traveling Waves
1619
(b) Relate the speed of the waves to the tension in the string and its linear density: km/s0.32
m/s316.2kg/m0.010kN1.0T
=
===μFv
(c) Use the relationship between the wavelength, speed and frequency of a wave to find λ:
cm79
cm79.05s400m/s316.2
1
=
=== −fvλ
Using its definition, express and evaluate the wave number:
1
12
m9.7
m95.7m1005.79
22
−
−−
=
=×
==π
λπk
(d) Determine the angular frequency of the waves:
( ) 131 s102.51s40022 −− ×=== ππω f
Substitute for A, k, and ω in the general form of the wave function to obtain:
( ) ( ) ( )[ ( ) ]txx,ty 131 s1051.2m9.7sinmm50.0 −− ×−=
(e) Relate the maximum speed of a point on the string to the amplitude of the waves and the angular frequency of the tuning fork:
( )( )m/s1.3
s102.51m100.50 133max
=
××=
=−−
ωAv
Express the maximum acceleration of a point on the string in terms of the amplitude of the waves and the angular frequency of the tuning fork:
( )( )2
2133
2max
km/s2.3
s102.51m100.50
=
××=
=−−
ωAa
(f) Express the minimum average power required to keep the tuning fork oscillating at a steady amplitude in terms of the linear density of the string, the amplitude of its vibrations, and the speed of the waves on the string:
vAP 2221
av μω=
Chapter 15
1620
Substitute numerical values and evaluate Pav:
( )( ) ( ) ( ) W25m/s316m100.50s102.51kg/m0.10 2321321
av =××= −−P
103 ••• A long rope with a mass per unit length of 0.100 kg/m is under a constant tension of 10.0 N. A motor drives one end of the rope with transverse simple harmonic motion at 5.00 cycles per second and an amplitude of 40.0 mm. (a) What is the wave speed? (b) What is the wavelength? (c) What is the maximum transverse linear momentum of a 1.00-mm segment of the rope? (d) What is the maximum net force on a 1.00-mm segment of the rope? Picture the Problem Let Δm represent the mass of the segment of length Δx = 1.00 mm. We can find the wave speed from the given data for the tension in the rope and its linear density. The wavelength can be found from v = fλ. We’ll use the definition of linear momentum to find the maximum transverse linear momentum of the 1-mm segment and apply Newton’s 2nd law to the segment to find the maximum net force on it. (a) Find the wave speed from the tension and linear density:
m/s10.0kg/m0.100N10.0T ===
μFv
(b) Express the wavelength in terms of the speed and frequency of the wave:
m2.00s5.00m/s10.0
1 === −fvλ
(c) Relate the maximum transverse linear momentum of the 1.00-mm segment to the maximum transverse speed of the wave:
xAfxAmvp Δ=Δ=Δ= μπωμ 2maxmax
Substitute numerical values and evaluate pmax:
( )( )( )( )
m/skg1026.1
m/skg10257.1m0.0400m101.00
kg/m0.100s5.002
4
4
3
1max
⋅×=
⋅×=
××
=
−
−
−
−πp
(d) The maximum net force acting on the segment is the product of the mass of the segment and its maximum acceleration:
max
max2
maxmax
2ΔΔ
fppxAmaF
πωωμ
====
Traveling Waves
1621
Substitute numerical values and evaluate Fmax:
( )( )mN95.3
m/skg101.257s5.002 41max
=
⋅×= −−πF
104 ••• In this problem, you will derive an expression for the potential energy of a segment of a string carrying a traveling wave (Figure 15-34). The potential energy of a segment equals the work done by the tension in stretching the string, which is ΔU = FT Δ − Δx( ), where FT is the tension, Δ is the length of the stretched segment, and Δx is its original length. From the figure we see that
( ) ( ) ( ) 21222 1 xyxyx ΔΔ+Δ=Δ+Δ=Δ .
(a) Use the binomial expansion to show that ( ) xxyx ΔΔΔΔΔ 2
21≈− , and
therefore xxyFU Δ
ΔΔΔ
2
T21 ⎟
⎠⎞
⎜⎝⎛≈ . (b) Compute dy/dx from the wave function
( ) ( )tkxAtxy ω−= sin, (Equation 15.-15) and show that ( ) xtkxkAFU Δ−≈ ω222
T21 cosΔ .
Picture the Problem We can follow the step-by-step instructions outlined above to obtain the given expressions for ΔU.
(a) Express the potential energy of a segment of the string:
( )xFU ΔΔΔ T −=
For Δy/Δx << 1:
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛+=
2
21
ΔΔ1ΔΔ
xyx
and
xxy
xxyxx
ΔΔΔ
ΔΔΔ1ΔΔΔ
2
21
2
21
⎟⎠⎞
⎜⎝⎛=
−⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛+=−
Substitute to obtain:
xxyF
xyFU Δ
ΔΔ
ΔΔΔ
2
T21
2
21
T ⎟⎠⎞
⎜⎝⎛=
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛=
(b) Differentiate
( ) ( )tkxAx,ty ω−= sin to obtain:
( )tkxkAdxdy ω−= cos
Chapter 15
1622
Approximate Δy/Δx by dy/dx and substitute in our result from Part (a):
( )( )( )tkxxkAF
xtkxkAFU
ω
ω
−Δ=
Δ−=222
T21
2T2
1
cos
cosΔ
Traveling Waves
1623
Chapter 15
1624
top related