advanced raiway security system based on zigbee communication for track fault

CONTENTS ABSTRACT LITERATURE SURVEY PROBLEM IDENTIFICATION EXPLANATION PROBLEMS -SOLUTIONS APPLICATIONS FUTURE SCOPE CONCLUSION REFERENCES

ABSTRACT

• The Transportation of train always depends on railway tracks (rails) only. If there is a crack in these rails, it creates a major problem. Most of the accidents in the train are caused due to cracks in the railway tracks, which cannot be easily identified. In order to avoid this problem, we are using the crack detector robot,By the using of this method to identifying rail track fault sending message to near station using ZIGBEE communication.

LITERATURE SURVEYVISUAL INSPECTION METHOD

by Ashwini Belkhade, Snehal Kathale First organized a survey of existing

technologies of automatic visual inspection of railroad track and track components.

This gave understanding with respect to which assignments were best suited to vision based assessment for which technology was not already under development.

This survey encompassed well-established inspection technologies and experimental technologies currently under development.

• Safety in railways is one of the major issues for public transportation organization and a fast and efficient inspection system is vital to ensure the safety of railways. Authors had tried to provide effective solution on the problem.

• Automatic railroad track inspection with the help of vision based method. Vision based system there are some cameras for collecting the images or videos of rail track and process the frame image by using image processing.

• In such manner it could enhance the efficiency of the traditional methods.

• The System challenges the following addressed: detection,fragmentation,deformity evaluation of track components whose physically appearance vary across number of tracks and the identification and inspection of track areas such as track turnouts.

VIBRATION BASED METHOD M. Singh, S.Singh1,J.Jaiswal

In this method a sensors will sense the vibration with the help of vibration sensor and after that it will pass to the op-amplifier filter for removing external noise and microcontroller for programming.

There is one communication protocol to establish the connection between the hardware and system .In system processing will be done and than it will broadcast to the server through wireless medium.

RAIWAYGAUGE INSPECTION METHOD S.Zheng, X.An, X.Chai

• Railway track gauge irregularity severely reduces the service life of rail and vehicle, and even result in vehicle falling off rail or wheel trapping, which causes driving accidents. In this project a dynamic inspection method of track gauge based on computer vision is presented. According to the method, the inspection system could be constructed by using four CCD (Charge-coupled Device) cameras and two red laser sector lights.

• The inspection principle and corresponding calibration method of inspection system are analyzed. In order to get the gauge points, several image processing technologies, including image component extraction, differential, adaptive iteration threshold, dilation and thinning are adopted.

• At last, the experiment results prove that this inspection method is capable of fast obtaining track gauge value with high accuracy and repeatability, and meeting the requirement of dynamic inspection for track gauge.

EXISTING SYSTEM

Pushing TrolleyRail Cycle with 2or3or4 wheelsOral communication through telephonic and

telegraphic conversations.

EXISTING METHOD VIEWS

PROBLEM IDENTIFY

• Cracks in the railway tracks

PROPOSED SYSTEM the design of crack finding robot for finding cracks in

railway tracks,This system uses controller for interfacing the robotic vehicle and crack detection sensor. The sensing device senses the voltage variations from the crack sensor(IR) and then it gives the signal to the microcontroller from that connected to zibgee communication.

BLOCKDIAGRAMS

ARM 7 TDMI

LPC2148

H-Bridge

G

P

I

O

DC Geared

Motor 1

DC Geared

Motor 2

RF Receiver

MAX

232

U

A

R

T

Track Detecting

Sensor

Sensing Device

Buzzer

Power SupplyTransmitter section:

Receiver unit:

Current driver

60dB Siren

A

T

8

9

S

5

2

16X2 LCD

Contrast control

RESET

RF Transmitter

MAX

232

Crystal

“Zigbee”

• ZigBee is an IEEE 802.15.4-based specification for a suite of high-level communication protocols used to create personal area networks with small, low-power digital radios.

• ZigBee specification is intended to be simpler and less expensive than other wireless personal area networks (WPANs), such as Bluetooth or Wi-Fi. Applications include wireless light switches, electrical meters with in-home-displays.

• Its low power consumption limits transmission distances to 10–100 meters line-of-sight, depending on power output and environmental characteristics.

• ZigBee devices can transmit data over long distances by passing data through a mesh network of intermediate devices to reach more distant ones.

• ZigBee is typically used in low data rate applications that require long battery life

Differences Standard

ZigBee®

802.15.4

Wi-Fi™

802.11b

Bluetooth™

802.15.1

Transmission Range

(meters)

1 – 100* 1 – 100 1 – 10

Battery Life (days) 100 – 1,000 0.5 – 5.0 1 – 7

Network Size (# of

nodes)

> 64,000 32 7

ApplicationMonitoring &

Control

Web, Email, Video Cable Replacement

Stack Size (KB) 4 – 32 1,000 250

Throughput kb/s) 20 – 250 11,000 720

Max232

The MAX232 is an integrated circuit by Maxim Integrated Products that converts signals from a TIA-232 (RS-232) serial port to signals suitable for use in TTL compatible digital logic circuits. The MAX232 is a dual driver/receiver and typically converts the RX, TX, CTS and RTS signals.

LPC 2148

• LPC2148 is the widely used IC from ARM-7 family.

• 8 to 40 kB of on-chip static RAM and 32 to 512 kB of on-chip flash program memory.

AT89S52

• Low-power, high-performance CMOS 8-bit microcontroller with 8KB of ISP flash memory. The device uses Atmel high-density, nonvolatile memory.

UART

• A universal asynchronous receiver/transmitter, A UART is a computer hardware device that translates data between parallel and serial forms. UARTs are commonly used in conjunction with communication standards such as TIA (formerly EIA) RS-232, RS-422.

GPIO

• General-purpose input/output (GPIO) is a generic pin on an integrated circuit whose behaviour including whether it is an input or output pin is controllable by the user at run time.

CURRENT DRIVER

• In electronics, a driver is an electrical circuit or other electronic component used to control another circuit or component, such as a high-power transistor, liquid crystal display (LCD), and numerous others.

Problem-solutions(ABOUT TRACK FAULT DETECTION)

Let us discuss problem and solution. Previous, rail inspection methods include destructive techniques, such as coring, and non-destructive techniques, such as hammer sounding.

But these methods just “cover limited space and have limited effectiveness in identifying the faults. Further non-destructive evaluation techniques for rail track inspection had developed.

These technologies include visual inspection, ground penetrating radar (GPR), X-ray and laser light.

• In order to avoid this problem, we are using the crack detector robot, which detects the crack in the rails and gives an alarm.A robot is an apparently human automation, intelligent and obedient but impersonal machine

ADVANTAGES

It reduces the man power.Crack detecting efficiency is high.Accuracy is high.

Applications

• Can be used for Railway Department.• Used in detecting applications

FUTURE SCOPE

• The geographical positioning sensors are placed on the trains. These sensors send the train’s geographic location

• Track fault detection solve the robot.

CONCLUSIONAccidents occurring in railway transportation systems cost a large number of lives. Many people die and several others get physical and mentally injured.

Wireless sensor network which continuously monitors the railway track through the sensors and detect any abnormality in the track.

REFERENCES• C. Campos-Castellanos, Y.Gharaibeh, P. Mudge *, V. Kappatos, “The

application of long range ultrasonic testing (LRUT) For examination of hard to access areas on railway tracks”. IEEE Railway Condition Monitoring and NonDestructive Testing (RCM 2011) Nov 2011.

• M. Singh, S.Singh1,J.Jaiswal, J. Hempshall “Autonomus rail track inspection using vision based system” .IEEE International Conference on Computational Intelligence for Homeland Security and Personal Safety pp 5659 .October 2006.

• S.Zheng, X.An, X.Chai, L. Li “Railway track gauge inspection method based on computer vision” IEEE International Conference on Mechatronics and Automation, pp 1292-1296 year of 2012.

• D.Hesse “Rail inspection using ultrasonic surface waves” Thesis ,Imperial College of London,2007

THANK YOU