accessory assembly full
Post on 14-Apr-2018
220 Views
Preview:
TRANSCRIPT
-
7/27/2019 Accessory Assembly Full
1/10
PAPER CRAFT
Assembly instructions: Ten A4-sized sheets.
Paper craft: Twelve A4-sized sheets with 136 parts in all
Thank you for downloading the YZF-R1 realistic paper craft Accessory
Kit. To complete assembly of the kit, refer to this manual and the assem-bly symbols indicated on the pattern sheets.
Assembly Instructions
* The patterns for the miniature realistic paper craft, YZF-R1 are not included in
this file. They can be downloaded separately from the corresponding links.
These instructions apply only to the "Accessory Kit".
These Paper Craft parts are easier to work with when printed out on strong,
thick paper (like postcard stock).
*In creating these Paper Craft models we use 135kg Kent paper stock (0.18mm).
-
7/27/2019 Accessory Assembly Full
2/10
- 2 -
Note
Items of Caution
*Take care when using sharp or pointed objects or when
using bladed cutting tools. Place a heavy sheet of paper
under the paper you want to cut.
*Use glue and other adhesives only in well-ventilated
areas.*When printing, use a slightly reduced font size. There
may be differences in dimensions, depending on the type
of printer used.
Tools and materials needed
-Ruler -scissors - blade cutter or "Exacto-knife" - awl or
other pointed tool (for making a folding crease) - felt pen
- pin set - glue - hand towel ( for cleaning your fingers) -
dictionary or other heavy book ( to press the papers flat).
*Cut carefully with cutting blade, Exacto-knife or
scissors.
*For folding parts, first use an awl or other pointed
tool to make a light crease along the dotted or solid
line. This will make the folds straight. Avoid making
strong creases, as this will cause the paper to tear.
*As an adhesive, white wood glue is recommended.
Avoid over application as this will cause the paper
to wrinkle.
*Before beginning assembly, test adhesive amounts
on extra paper.
*Occasionally, white spots will be apparent on folds
and cuts. Use a marker or pencil to fill in these spots.
It is recommended that this be done after each stage
of assembly because coloring becomes more diffi-
cult once parts are assembled.
TO BEGIN
HOW TO ASSEMBLE
One - point Advice
*Follow the working method and markings carefully.
*Cut carefully along the outter line with cutting blade,
Exacto-knife or scissors.
Fold along these lines. The printed
surface should be on the outside of
the folded shape.
Solid lines
Dotted line
Fold along these lines. The printed
surface should be on the inside of
the folded shape.
Broken lines
Cut out parts marked with an as-
terisk(*).
Cut along these lines.
Do not fold or cut the parts
marked .
Basic working method and markings
Red dots are the reference positions
for gluing surfaces.
-
7/27/2019 Accessory Assembly Full
3/10
- 3 -
A-42~47
Tool-a
A-99i101j
1 Assembling the Tool BoxFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
ToolsSheet A-8, 60 parts in total
Fold each relevant part according to the assembly symbols.
* Freely display the tools in the functional drawers of the tool box.
Fold only the edges. Fold only the edges.
Make six replicas of the part invarious sizes.
Make nine replicas of the part invarious sizes.
A-48~56
Tool-b Tool-c
A-94 (96)A-95 (97)
Make two different-sized repli-cas of each part.
Tool-dA-86 (87) (91) (92) (93)
A-84 (85) (88) (89) (90)
Make five different-sized replicas ofeach part.
Tool-e
A-57 (58) (59)
Make three replicas of the part.
Make sixteen replicas of the partin various sizes.
A-68~83Tool-i
Tool-f
A-60 (61)
Make two replicas of the part.
Tool-g
A-66 (67)
Make two replicas of the part.
Tool-h
A-64 (65)
Make two replicas of the part.
Tool-i
A-62 (63)
Make two replicas of the part.Make two replicas of the part invarious sizes.
Tool-k A-98 (100)
Insert and gluepart A-99 aftermaking a slit inpart A-98.
-
7/27/2019 Accessory Assembly Full
4/10
- 4 -
1 Assembling the Tool BoxFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
DrawersSheet A-5.6.7, 23 parts in total
Fold each relevant part according to the assembly symbols.
Drawer- a. b Make two replicas of each part.
A-36 (37)
A-40 (41)
Drawer- c
A-38
A-39
Drawer- d. e. f A-29 (30)(31)
Make three replicasof each part.
A-24 (25)(26)
Drawer- g(dummy)
A-21
A-22
A-23 A-28
Drawer- h(dummy)
A-19 A-20 A-27
Drawer- i A-33
A-32
Drawer-j
A-34
A-35
-
7/27/2019 Accessory Assembly Full
5/10
- 5 -
Lid
Tuck the part incompletely andglue it.
A-7 (8)
A-3Tuck the part incompletely andglue it.
Inner walls- top board and bottom board
A-7 is to be the top boardand A-8 the bottom board.
Inner walls-central part- vertical
A-5
Inner walls-central part- horizontal
A-6 A-9 (10)
Inner walls- left and right
A-15 (16) (17) (18)
Wheels
A-11 (12) (13) (14)
Make four identical wheels.
1 Assembling the Tool BoxFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
Body of Tool BoxSheet A-2.3.4.5, 15 parts in total
Fold each relevant part according to the assembly symbols.
Looking at the diagram, A-9should be on the left and A-10
on the right.
-
7/27/2019 Accessory Assembly Full
6/10
Glue folded A-1 to .
- 6 -
A-2
A-1
A-4
Assemble according to steps through .
Lid
Glue six previously assembled boards of the inner walls.
Assembly Instructions
Glue the inner walls to A-2.
Insert and glue the previously assembled drawers in place.
Note: Freely place tools in the functional drawers.
Carefully keep the lid open when gluing it to A-2. Also glue
A-4 between the lid and A-1.
Glue each wheel to the bottom board.
Reference photo
Inner walls- bottom board
Inner walls- top board
Inner walls-central part- vertical
Inner walls-central part- horizontal
Inner walls- left
Inner walls- right
Drawer- a
Drawer- b
Drawer- c
Drawer- dDrawer- e
Drawer- f
Drawer- hDrawer- g
Drawer- iDrawer- j
Wheels
1 Assembling the Tool BoxFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
FinishFold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
-
7/27/2019 Accessory Assembly Full
7/10
- 7 -
B-1
B-2
B-3
B-4
B-5
B-6
B-7
Assembling the Engine OilFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
Engine OilSheet B, 7 parts in total
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Engine Oil / Large Engine Oil / Small
Glue B-3 according tothe dotted line on B-2.
Reference photo
2
-
7/27/2019 Accessory Assembly Full
8/10
- 8 -
C-1
C-2
C-3
C-4
C-8
C-7
C-6
C-5
Assembling the Maintenance ChemicalsFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
Maintenance ChemicalsSheet C, 8 parts in total
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
3
Long Life Coolant
Glue C-3 according tothe dotted line on C-2.
Grease Spray Filter Oil / Small
Filter Oil / Large
Reference photo
-
7/27/2019 Accessory Assembly Full
9/10
- 9 -
Assemble and glue in place D-2, D-3, D-4, D-5, D-10, D-11, D-13, and D-14.
Glue , , D-8, and D-9 according to the diagram.
Glue to D-12.
Glue D-1 to according to the diagram.
Assemble the wheel parts, D-6 and D-7.
D-1
D-2D-3 D-4D-5
D-8
D-9
D-6D-7
D-10D-11
D-13
D-14
D-12
Assembling the StandFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
StandSheet D, 14 parts in total
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
4
Assembly Instructions
Reference photo
-
7/27/2019 Accessory Assembly Full
10/10
- 10 -
E-1
E-2
E-3
E-4
E-5
E-6
Assembling the Rear TireFirst, assemble each component by following theworking method and markings. Then, refer to the il-lustration and photos below to glue the parts together.
Indication ofWorking Methods Fold or Curve Adhere
Sheet E, 6 parts in total
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
5
REAR TIRE
Gluing area
Reference photo
top related