allet conveyor systems - pallet handling catalogue … · rollers rulmeca Ø 89 mm roller, 3 mm...
TRANSCRIPT
PALLET HANDLING CONVEYOR SYSTEMS
PRE-ENGINEERED
PALLET HANDLING CONVEYOR SYSTEMS
Series 100.10
CE DRIVES
30/05/2019 V100.10.1.20
PALLET HANDLING CONVEYOR SYSTEMS
Pallet Stacker/Destacker 100.10.90.40
- 49 -
Rail Guided Vehicle 100.10.10.40.10
- 38 -
Chain Conveyor 100.10.10.20
- 20 -
Roller Conveyor 100.10.10.10.10
- 3 -
Forklift Bumper 100.10.90.10
- 51 -
Turntable 100.10.10.50.10
- 42 -
Single Level Transfer 100.10.10.10.10
- 3 -
FORKLIFT GUIDES FOR PALLETS
- 52 -
PALLET HANDLING CONVEYOR SYSTEMS
1
PALLET HANDLING CONVEYOR SYSTEMS
ROLLER CONVEYOR - 3 -
CHAIN CONVEYOR - 20 -
SINGLE LEVEL TRANSFER - 34-
RAIL GUIDED VEHICLE - 38-
TURNTABLE - 42 -
PALLET STACK GUIDE - 45 -
PALLET STACKER/DESTACKER - 49 -
FORKLIFT BUMPER - 51 -
FORKLIFT GUIDES FOR PALLETS - 52 -
PALLET HANDLING CONVEYOR SYSTEMS
2
EUR PALLET
800/1000/1200
1200
GMA PALLET
1016/1219 1219
FULL BASE PALLET
1000 1200
PALLET TYPE
PALLET SPECIFICATIONS PALLET TYPE DIMENSIONS
(mm) TRANSPORT APLICATION
ROLLER CONVEYOR TRANSPORT APLICATION
CHAIN CONVEYOR EUR 1 800x1200 Short side leading Long side leading EUR 2 1000x1200 Short side leading Long side leading EUR 3 1200x1200 Short side leading Long side leading
GMA type - 40’’x48’’ 1016x1219 Long side leading Short side leading GMA type - 48’’x48’’ 1219x1219 Long side leading Short side leading
Full base pallet 1000x1200 Both sides leading Both sides leading
EQUIPMENT SELECTION To select the correct conveyor type, the complete load definition is required. The above table helps to decide each conveyor to choose depending on pallet and transport direction. Other products besides pallets can be conveyed. Further information rather the pallet type should be considered during equipment’s selection such as: - Pallet or product quality; - Overhanging load; - Pallet or product loading/unloading method. For more specific information, please contact Antípoda.
PALLET HANDLING CONVEYOR SYSTEMS
3
Walkover Plates 100.10.10.10.90.20
- 15 -
ROLLER CONVEYOR
Fixed Stopper 100.10.10.10.90.30
- 16 -
Pneumatic Stopper 100.10.10.10.90.40
- 17 -
Pneumatic Pusher 100.10.10.10.90.50
- 18 -
Drive Module 100.10.10.10.90.100
- 12 -
Adjustable Photocell Support 100.10.10.10.90.60
- 19 -
Supports 100.10.10.10.90.10
- 13 -
PALLET HANDLING CONVEYOR SYSTEMS
4
ROLLER CONVEYOR ROLLER TO ROLLER TRANSMISSION
*200 – nominal pitch of 198,44 mm 1 2 3 4 5
100.10.10.10.10 . . . . ORDER EXAMPLE: 100.10.10.10.10.1130.175.2975 Roller conveyor, roller to roller transmission, 1130 mm between frames, 175 mm roller pitch, 2975 mm conveyor length without guide rings.
SPECIFICATIONS Frame 3 mm steel frame. Standard coating RAL 9006. Other colors upon request. Rollers RULMECA Ø 89 mm roller, 3 mm thickness zinc plated steel tube. Ø20 mm,
M12 internally threaded shaft. 6205-2rs bearings. 10B-1 sprockets with zinc plated finish. Roller lengths 930 mm, 1130 mm and 1330 mm available. Other roller lengths upon request. Guide-rings welded on center or both sides on specification.
Pitch 150 mm, 175 mm and 198,44 mm. Payload Up to 1,500 kg considering a 1200x800 mm pallet with a uniformly distributed
load. Maximum number of pallets on the conveyor as specified on TABLE 1, TABLE 2 and TABLE 3.
Drive SEW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Speed 12 m/min. Inclined/Declined Not suitable. Horizontal application only. Direction Both. Supports Not included. See TABLE 8 on page 13. Ambient temperature 5oC to 50oC.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.10 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 PITCH (mm)
150 | 175 | 200* 4 LENGTH (mm) 5 GUIDE RINGS DISTANCE (mm)
BLANK: NO GUIDE RINGS 175 ≤ DISTANCE ≤ BETWEEN FRAMES (mm) – 100 mm
DIMENSIONS BF BETWEEN FRAMES P ROLLER PITCH L LENGTH
PALLET HANDLING CONVEYOR SYSTEMS
5
ROLLER CONVEYOR ROLLER TO ROLLER TRANSMISSION ROLLER PITCH 150 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 1
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1350 100.10.10.10.10.930.150.1350 100.10.10.10.10.1130.150.1350 100.10.10.10.10.1330.150.1350 1 0,18 2 1500 100.10.10.10.10.930.150.1500 100.10.10.10.10.1130.150.1500 100.10.10.10.10.1330.150.1500 1 0,18 2 1650 100.10.10.10.10.930.150.1650 100.10.10.10.10.1130.150.1650 100.10.10.10.10.1330.150.1650 1 0,18 2 1800 100.10.10.10.10.930.150.1800 100.10.10.10.10.1130.150.1800 100.10.10.10.10.1330.150.1800 1 0,18 2 1950 100.10.10.10.10.930.150.1950 100.10.10.10.10.1130.150.1950 100.10.10.10.10.1330.150.1950 1 0,18 2 2100 100.10.10.10.10.930.150.2100 100.10.10.10.10.1130.150.2100 100.10.10.10.10.1330.150.2100 1 0,18 2 2250 100.10.10.10.10.930.150.2250 100.10.10.10.10.1130.150.2250 100.10.10.10.10.1330.150.2250 1 0,18 2 2400 100.10.10.10.10.930.150.2400 100.10.10.10.10.1130.150.2400 100.10.10.10.10.1330.150.2400 1 0,18 2 2550 100.10.10.10.10.930.150.2550 100.10.10.10.10.1130.150.2550 100.10.10.10.10.1330.150.2550 2 0,37 3 2700 100.10.10.10.10.930.150.2700 100.10.10.10.10.1130.150.2700 100.10.10.10.10.1330.150.2700 2 0,37 3 2850 100.10.10.10.10.930.150.2850 100.10.10.10.10.1130.150.2850 100.10.10.10.10.1330.150.2850 2 0,37 3 3000 100.10.10.10.10.930.150.3000 100.10.10.10.10.1130.150.3000 100.10.10.10.10.1330.150.3000 2 0,37 3 3150 100.10.10.10.10.930.150.3150 100.10.10.10.10.1130.150.3150 100.10.10.10.10.1330.150.3150 2 0,37 3 3300 100.10.10.10.10.930.150.3300 100.10.10.10.10.1130.150.3300 100.10.10.10.10.1330.150.3300 2 0,37 3 3450 100.10.10.10.10.930.150.3450 100.10.10.10.10.1130.150.3450 100.10.10.10.10.1330.150.3450 2 0,37 3 3600 100.10.10.10.10.930.150.3600 100.10.10.10.10.1130.150.3600 100.10.10.10.10.1330.150.3600 2 0,37 3 3750 100.10.10.10.10.930.150.3750 100.10.10.10.10.1130.150.3750 100.10.10.10.10.1330.150.3750 3 0,75 4 3900 100.10.10.10.10.930.150.3900 100.10.10.10.10.1130.150.3900 100.10.10.10.10.1330.150.3900 3 0,75 4 4050 100.10.10.10.10.930.150.4050 100.10.10.10.10.1130.150.4050 100.10.10.10.10.1330.150.4050 3 0,75 4 4200 100.10.10.10.10.930.150.4200 100.10.10.10.10.1130.150.4200 100.10.10.10.10.1330.150.4200 3 0,75 4 4350 100.10.10.10.10.930.150.4350 100.10.10.10.10.1130.150.4350 100.10.10.10.10.1330.150.4350 3 0,75 4 4500 100.10.10.10.10.930.150.4500 100.10.10.10.10.1130.150.4500 100.10.10.10.10.1330.150.4500 3 0,75 4 4650 100.10.10.10.10.930.150.4650 100.10.10.10.10.1130.150.4650 100.10.10.10.10.1330.150.4650 3 0,75 4 4800 100.10.10.10.10.930.150.4800 100.10.10.10.10.1130.150.4800 100.10.10.10.10.1330.150.4800 3 0,75 4 4950 100.10.10.10.10.930.150.4950 100.10.10.10.10.1130.150.4950 100.10.10.10.10.1330.150.4950 4 0,75 5 5100 100.10.10.10.10.930.150.5100 100.10.10.10.10.1130.150.5100 100.10.10.10.10.1330.150.5100 4 0,75 5 5250 100.10.10.10.10.930.150.5250 100.10.10.10.10.1130.150.5250 100.10.10.10.10.1330.150.5250 4 0,75 5 5400 100.10.10.10.10.930.150.5400 100.10.10.10.10.1130.150.5400 100.10.10.10.10.1330.150.5400 4 0,75 5 5550 100.10.10.10.10.930.150.5550 100.10.10.10.10.1130.150.5550 100.10.10.10.10.1330.150.5550 4 0,75 5 5700 100.10.10.10.10.930.150.5700 100.10.10.10.10.1130.150.5700 100.10.10.10.10.1330.150.5700 4 0,75 5 5850 100.10.10.10.10.930.150.5850 100.10.10.10.10.1130.150.5850 100.10.10.10.10.1330.150.5850 4 0,75 5 6000 100.10.10.10.10.930.150.6000 100.10.10.10.10.1130.150.6000 100.10.10.10.10.1330.150.6000 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
6
ROLLER CONVEYOR ROLLER TO ROLLER TRANSMISSION ROLLER PITCH 175 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 2
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1400 100.10.10.10.10.930.175.1400 100.10.10.10.10.1130.175.1400 100.10.10.10.10.1330.175.1400 1 0,18 2 1575 100.10.10.10.10.930.175.1575 100.10.10.10.10.1130.175.1575 100.10.10.10.10.1330.175.1575 1 0,18 2 1750 100.10.10.10.10.930.175.1750 100.10.10.10.10.1130.175.1750 100.10.10.10.10.1330.175.1750 1 0,18 2 1925 100.10.10.10.10.930.175.1925 100.10.10.10.10.1130.175.1925 100.10.10.10.10.1330.175.1925 1 0,18 2 2100 100.10.10.10.10.930.175.2100 100.10.10.10.10.1130.175.2100 100.10.10.10.10.1330.175.2100 1 0,18 2 2275 100.10.10.10.10.930.175.2275 100.10.10.10.10.1130.175.2275 100.10.10.10.10.1330.175.2275 1 0,18 2 2450 100.10.10.10.10.930.175.2450 100.10.10.10.10.1130.175.2450 100.10.10.10.10.1330.175.2450 1 0,18 2 2625 100.10.10.10.10.930.175.2625 100.10.10.10.10.1130.175.2625 100.10.10.10.10.1330.175.2625 2 0,37 3 2800 100.10.10.10.10.930.175.2800 100.10.10.10.10.1130.175.2800 100.10.10.10.10.1330.175.2800 2 0,37 3 2975 100.10.10.10.10.930.175.2975 100.10.10.10.10.1130.175.2975 100.10.10.10.10.1330.175.2975 2 0,37 3 3150 100.10.10.10.10.930.175.3150 100.10.10.10.10.1130.175.3150 100.10.10.10.10.1330.175.3150 2 0,37 3 3325 100.10.10.10.10.930.175.3325 100.10.10.10.10.1130.175.3325 100.10.10.10.10.1330.175.3325 2 0,37 3 3500 100.10.10.10.10.930.175.3500 100.10.10.10.10.1130.175.3500 100.10.10.10.10.1330.175.3500 2 0,37 3 3675 100.10.10.10.10.930.175.3675 100.10.10.10.10.1130.175.3675 100.10.10.10.10.1330.175.3675 2 0,37 3 3850 100.10.10.10.10.930.175.3850 100.10.10.10.10.1130.175.3850 100.10.10.10.10.1330.175.3850 3 0,75 4 4025 100.10.10.10.10.930.175.4025 100.10.10.10.10.1130.175.4025 100.10.10.10.10.1330.175.4025 3 0,75 4 4200 100.10.10.10.10.930.175.4200 100.10.10.10.10.1130.175.4200 100.10.10.10.10.1330.175.4200 3 0,75 4 4375 100.10.10.10.10.930.175.4375 100.10.10.10.10.1130.175.4375 100.10.10.10.10.1330.175.4375 3 0,75 4 4550 100.10.10.10.10.930.175.4550 100.10.10.10.10.1130.175.4550 100.10.10.10.10.1330.175.4550 3 0,75 4 4725 100.10.10.10.10.930.175.4725 100.10.10.10.10.1130.175.4725 100.10.10.10.10.1330.175.4725 3 0,75 4 4900 100.10.10.10.10.930.175.4900 100.10.10.10.10.1130.175.4900 100.10.10.10.10.1330.175.4900 4 0,75 5 5075 100.10.10.10.10.930.175.5075 100.10.10.10.10.1130.175.5075 100.10.10.10.10.1330.175.5075 4 0,75 5 5250 100.10.10.10.10.930.175.5250 100.10.10.10.10.1130.175.5250 100.10.10.10.10.1330.175.5250 4 0,75 5 5425 100.10.10.10.10.930.175.5425 100.10.10.10.10.1130.175.5425 100.10.10.10.10.1330.175.5425 4 0,75 5 5600 100.10.10.10.10.930.175.5600 100.10.10.10.10.1130.175.5600 100.10.10.10.10.1330.175.5600 4 0,75 5 5775 100.10.10.10.10.930.175.5775 100.10.10.10.10.1130.175.5775 100.10.10.10.10.1330.175.5775 4 0,75 5 5950 100.10.10.10.10.930.175.5950 100.10.10.10.10.1130.175.5950 100.10.10.10.10.1330.175.5950 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
7
ROLLER CONVEYOR ROLLER TO ROLLER TRANSMISSION ROLLER PITCH 198.44 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 3
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1400 100.10.10.10.10.930.200.1400 100.10.10.10.10.1130.200.1400 100.10.10.10.10.1330.200.1400 1 0,18 2 1600 100.10.10.10.10.930.200.1600 100.10.10.10.10.1130.200.1600 100.10.10.10.10.1330.200.1600 1 0,18 2 1800 100.10.10.10.10.930.200.1800 100.10.10.10.10.1130.200.1800 100.10.10.10.10.1330.200.1800 1 0,18 2 2000 100.10.10.10.10.930.200.2000 100.10.10.10.10.1130.200.2000 100.10.10.10.10.1330.200.2000 1 0,18 2 2200 100.10.10.10.10.930.200.2200 100.10.10.10.10.1130.200.2200 100.10.10.10.10.1330.200.2200 1 0,18 2 2400 100.10.10.10.10.930.200.2400 100.10.10.10.10.1130.200.2400 100.10.10.10.10.1330.200.2400 1 0,18 2 2600 100.10.10.10.10.930.200.2600 100.10.10.10.10.1130.200.2600 100.10.10.10.10.1330.200.2600 2 0,37 3 2800 100.10.10.10.10.930.200.2800 100.10.10.10.10.1130.200.2800 100.10.10.10.10.1330.200.2800 2 0,37 3 3000 100.10.10.10.10.930.200.3000 100.10.10.10.10.1130.200.3000 100.10.10.10.10.1330.200.3000 2 0,37 3 3200 100.10.10.10.10.930.200.3200 100.10.10.10.10.1130.200.3200 100.10.10.10.10.1330.200.3200 2 0,37 3 3400 100.10.10.10.10.930.200.3400 100.10.10.10.10.1130.200.3400 100.10.10.10.10.1330.200.3400 2 0,37 3 3600 100.10.10.10.10.930.200.3600 100.10.10.10.10.1130.200.3600 100.10.10.10.10.1330.200.3600 2 0,37 3 3800 100.10.10.10.10.930.200.3800 100.10.10.10.10.1130.200.3800 100.10.10.10.10.1330.200.3800 3 0,75 4 4000 100.10.10.10.10.930.200.4000 100.10.10.10.10.1130.200.4000 100.10.10.10.10.1330.200.4000 3 0,75 4 4200 100.10.10.10.10.930.200.4200 100.10.10.10.10.1130.200.4200 100.10.10.10.10.1330.200.4200 3 0,75 4 4400 100.10.10.10.10.930.200.4400 100.10.10.10.10.1130.200.4400 100.10.10.10.10.1330.200.4400 3 0,75 4 4600 100.10.10.10.10.930.200.4600 100.10.10.10.10.1130.200.4600 100.10.10.10.10.1330.200.4600 3 0,75 4 4800 100.10.10.10.10.930.200.4800 100.10.10.10.10.1130.200.4800 100.10.10.10.10.1330.200.4800 3 0,75 4 5000 100.10.10.10.10.930.200.5000 100.10.10.10.10.1130.200.5000 100.10.10.10.10.1330.200.5000 4 0,75 5 5200 100.10.10.10.10.930.200.5200 100.10.10.10.10.1130.200.5200 100.10.10.10.10.1330.200.5200 4 0,75 5 5400 100.10.10.10.10.930.200.5400 100.10.10.10.10.1130.200.5400 100.10.10.10.10.1330.200.5400 4 0,75 5 5600 100.10.10.10.10.930.200.5600 100.10.10.10.10.1130.200.5600 100.10.10.10.10.1330.200.5600 4 0,75 5 5800 100.10.10.10.10.930.200.5800 100.10.10.10.10.1130.200.5800 100.10.10.10.10.1330.200.5800 4 0,75 5 6000 100.10.10.10.10.930.200.6000 100.10.10.10.10.1130.200.6000 100.10.10.10.10.1330.200.6000 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
8
ROLLER CONVEYOR TANGENTIAL CHAIN TRANSMISSION
1 2 3 4 5 100.10.10.10.20 . . . .
ORDER EXAMPLE: 100.10.10.10.20.1130.175.2975 Roller conveyor, tangential chain transmission, 1130 mm between frames, 175 mm roller pitch, 2975 mm conveyor length without rings.
SPECIFICATIONS Frame 3 mm steel frame. Standard coating RAL 9006. Other colors upon request. Rollers RULMECA Ø 89 mm roller, 3 mm thickness zinc plated steel tube. Ø20 mm,
M12 internally threaded shaft. 6205-2rs bearings. 10B-1 sprockets with zinc plated finish. Roller lengths 930 mm, 1130 mm and 1330 mm available. Other roller lengths upon request. Guide-rings welded on center or both sides on specification.
Pitch 150 mm, 175 mm and 200 mm. Payload Up to 1,500 kg considering a 1200x800 mm pallet with a uniformly distributed
load. Maximum number of pallets on the conveyor as specified on TABLE 4, TABLE 5 and TABLE 6.
Drive SEW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Speed 12 m/min. Inclined/Declined Not suitable. Horizontal application only. Direction Both. Supports Not included. See TABLE 8 on page 13. Ambient temperature 5oC to 50oC
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.20 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 PITCH (mm)
150 | 175 | 200 4 LENGTH (mm) 5 GUIDE RINGS DISTANCE (mm)
BLANK: NO GUIDE RINGS 175 ≤ DISTANCE ≤ BETWEEN FRAMES (mm) – 100 mm
DIMENSIONS BF BETWEEN FRAMES P ROLLER PITCH L LENGTH
PALLET HANDLING CONVEYOR SYSTEMS
9
ROLLER CONVEYOR TANGENTIAL CHAIN TRANSMISSION ROLLER PITCH 150 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 4
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1350 100.10.10.10.20.930.150.1350 100.10.10.10.20.1130.150.1350 100.10.10.10.20.1330.150.1350 1 0,18 2 1500 100.10.10.10.20.930.150.1500 100.10.10.10.20.1130.150.1500 100.10.10.10.20.1330.150.1500 1 0,18 2 1650 100.10.10.10.20.930.150.1650 100.10.10.10.20.1130.150.1650 100.10.10.10.20.1330.150.1650 1 0,18 2 1800 100.10.10.10.20.930.150.1800 100.10.10.10.20.1130.150.1800 100.10.10.10.20.1330.150.1800 1 0,18 2 1950 100.10.10.10.20.930.150.1950 100.10.10.10.20.1130.150.1950 100.10.10.10.20.1330.150.1950 1 0,18 2 2100 100.10.10.10.20.930.150.2100 100.10.10.10.20.1130.150.2100 100.10.10.10.20.1330.150.2100 1 0,18 2 2250 100.10.10.10.20.930.150.2250 100.10.10.10.20.1130.150.2250 100.10.10.10.20.1330.150.2250 1 0,18 2 2400 100.10.10.10.20.930.150.2400 100.10.10.10.20.1130.150.2400 100.10.10.10.20.1330.150.2400 1 0,18 2 2550 100.10.10.10.20.930.150.2550 100.10.10.10.20.1130.150.2550 100.10.10.10.20.1330.150.2550 2 0,37 3 2700 100.10.10.10.20.930.150.2700 100.10.10.10.20.1130.150.2700 100.10.10.10.20.1330.150.2700 2 0,37 3 2850 100.10.10.10.20.930.150.2850 100.10.10.10.20.1130.150.2850 100.10.10.10.20.1330.150.2850 2 0,37 3 3000 100.10.10.10.20.930.150.3000 100.10.10.10.20.1130.150.3000 100.10.10.10.20.1330.150.3000 2 0,37 3 3150 100.10.10.10.20.930.150.3150 100.10.10.10.20.1130.150.3150 100.10.10.10.20.1330.150.3150 2 0,37 3 3300 100.10.10.10.20.930.150.3300 100.10.10.10.20.1130.150.3300 100.10.10.10.20.1330.150.3300 2 0,37 3 3450 100.10.10.10.20.930.150.3450 100.10.10.10.20.1130.150.3450 100.10.10.10.20.1330.150.3450 2 0,37 3 3600 100.10.10.10.20.930.150.3600 100.10.10.10.20.1130.150.3600 100.10.10.10.20.1330.150.3600 2 0,37 3 3750 100.10.10.10.20.930.150.3750 100.10.10.10.20.1130.150.3750 100.10.10.10.20.1330.150.3750 3 0,75 4 3900 100.10.10.10.20.930.150.3900 100.10.10.10.20.1130.150.3900 100.10.10.10.20.1330.150.3900 3 0,75 4 4050 100.10.10.10.20.930.150.4050 100.10.10.10.20.1130.150.4050 100.10.10.10.20.1330.150.4050 3 0,75 4 4200 100.10.10.10.20.930.150.4200 100.10.10.10.20.1130.150.4200 100.10.10.10.20.1330.150.4200 3 0,75 4 4350 100.10.10.10.20.930.150.4350 100.10.10.10.20.1130.150.4350 100.10.10.10.20.1330.150.4350 3 0,75 4 4500 100.10.10.10.20.930.150.4500 100.10.10.10.20.1130.150.4500 100.10.10.10.20.1330.150.4500 3 0,75 4 4650 100.10.10.10.20.930.150.4650 100.10.10.10.20.1130.150.4650 100.10.10.10.20.1330.150.4650 3 0,75 4 4800 100.10.10.10.20.930.150.4800 100.10.10.10.20.1130.150.4800 100.10.10.10.20.1330.150.4800 3 0,75 4 4950 100.10.10.10.20.930.150.4950 100.10.10.10.20.1130.150.4950 100.10.10.10.20.1330.150.4950 4 0,75 5 5100 100.10.10.10.20.930.150.5100 100.10.10.10.20.1130.150.5100 100.10.10.10.20.1330.150.5100 4 0,75 5 5250 100.10.10.10.20.930.150.5250 100.10.10.10.20.1130.150.5250 100.10.10.10.20.1330.150.5250 4 0,75 5 5400 100.10.10.10.20.930.150.5400 100.10.10.10.20.1130.150.5400 100.10.10.10.20.1330.150.5400 4 0,75 5 5550 100.10.10.10.20.930.150.5550 100.10.10.10.20.1130.150.5550 100.10.10.10.20.1330.150.5550 4 0,75 5 5700 100.10.10.10.20.930.150.5700 100.10.10.10.20.1130.150.5700 100.10.10.10.20.1330.150.5700 4 0,75 5 5850 100.10.10.10.20.930.150.5850 100.10.10.10.20.1130.150.5850 100.10.10.10.20.1330.150.5850 4 0,75 5 6000 100.10.10.10.20.930.150.6000 100.10.10.10.20.1130.150.6000 100.10.10.10.20.1330.150.6000 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
10
ROLLER CONVEYOR TANGENTIAL CHAIN TRANSMISSION ROLLER PITCH 175 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 5
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1400 100.10.10.10.20.930.175.1400 100.10.10.10.20.1130.175.1400 100.10.10.10.20.1330.175.1400 1 0,18 2 1575 100.10.10.10.20.930.175.1575 100.10.10.10.20.1130.175.1575 100.10.10.10.20.1330.175.1575 1 0,18 2 1750 100.10.10.10.20.930.175.1750 100.10.10.10.20.1130.175.1750 100.10.10.10.20.1330.175.1750 1 0,18 2 1925 100.10.10.10.20.930.175.1925 100.10.10.10.20.1130.175.1925 100.10.10.10.20.1330.175.1925 1 0,18 2 2100 100.10.10.10.20.930.175.2100 100.10.10.10.20.1130.175.2100 100.10.10.10.20.1330.175.2100 1 0,18 2 2275 100.10.10.10.20.930.175.2275 100.10.10.10.20.1130.175.2275 100.10.10.10.20.1330.175.2275 1 0,18 2 2450 100.10.10.10.20.930.175.2450 100.10.10.10.20.1130.175.2450 100.10.10.10.20.1330.175.2450 1 0,18 2 2625 100.10.10.10.20.930.175.2625 100.10.10.10.20.1130.175.2625 100.10.10.10.20.1330.175.2625 2 0,37 3 2800 100.10.10.10.20.930.175.2800 100.10.10.10.20.1130.175.2800 100.10.10.10.20.1330.175.2800 2 0,37 3 2975 100.10.10.10.20.930.175.2975 100.10.10.10.20.1130.175.2975 100.10.10.10.20.1330.175.2975 2 0,37 3 3150 100.10.10.10.20.930.175.3150 100.10.10.10.20.1130.175.3150 100.10.10.10.20.1330.175.3150 2 0,37 3 3325 100.10.10.10.20.930.175.3325 100.10.10.10.20.1130.175.3325 100.10.10.10.20.1330.175.3325 2 0,37 3 3500 100.10.10.10.20.930.175.3500 100.10.10.10.20.1130.175.3500 100.10.10.10.20.1330.175.3500 2 0,37 3 3675 100.10.10.10.20.930.175.3675 100.10.10.10.20.1130.175.3675 100.10.10.10.20.1330.175.3675 2 0,37 3 3850 100.10.10.10.20.930.175.3850 100.10.10.10.20.1130.175.3850 100.10.10.10.20.1330.175.3850 3 0,75 4 4025 100.10.10.10.20.930.175.4025 100.10.10.10.20.1130.175.4025 100.10.10.10.20.1330.175.4025 3 0,75 4 4200 100.10.10.10.20.930.175.4200 100.10.10.10.20.1130.175.4200 100.10.10.10.20.1330.175.4200 3 0,75 4 4375 100.10.10.10.20.930.175.4375 100.10.10.10.20.1130.175.4375 100.10.10.10.20.1330.175.4375 3 0,75 4 4550 100.10.10.10.20.930.175.4550 100.10.10.10.20.1130.175.4550 100.10.10.10.20.1330.175.4550 3 0,75 4 4725 100.10.10.10.20.930.175.4725 100.10.10.10.20.1130.175.4725 100.10.10.10.20.1330.175.4725 3 0,75 4 4900 100.10.10.10.20.930.175.4900 100.10.10.10.20.1130.175.4900 100.10.10.10.20.1330.175.4900 4 0,75 5 5075 100.10.10.10.20.930.175.5075 100.10.10.10.20.1130.175.5075 100.10.10.10.20.1330.175.5075 4 0,75 5 5250 100.10.10.10.20.930.175.5250 100.10.10.10.20.1130.175.5250 100.10.10.10.20.1330.175.5250 4 0,75 5 5425 100.10.10.10.20.930.175.5425 100.10.10.10.20.1130.175.5425 100.10.10.10.20.1330.175.5425 4 0,75 5 5600 100.10.10.10.20.930.175.5600 100.10.10.10.20.1130.175.5600 100.10.10.10.20.1330.175.5600 4 0,75 5 5775 100.10.10.10.20.930.175.5775 100.10.10.10.20.1130.175.5775 100.10.10.10.20.1330.175.5775 4 0,75 5 5950 100.10.10.10.20.930.175.5950 100.10.10.10.20.1130.175.5950 100.10.10.10.20.1330.175.5950 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
11
ROLLER CONVEYOR TANGENTIAL CHAIN TRANSMISSION ROLLER PITCH 200 mm
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 14.
REFERENCE NUMBER TABLE 6
LEN
GTH
(mm
)
BETWEEN FRAMES
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
930 mm 1130 mm 1330 mm 1400 100.10.10.10.20.930.200.1400 100.10.10.10.20.1130.200.1400 100.10.10.10.20.1330.200.1400 1 0,18 2 1600 100.10.10.10.20.930.200.1600 100.10.10.10.20.1130.200.1600 100.10.10.10.20.1330.200.1600 1 0,18 2 1800 100.10.10.10.20.930.200.1800 100.10.10.10.20.1130.200.1800 100.10.10.10.20.1330.200.1800 1 0,18 2 2000 100.10.10.10.20.930.200.2000 100.10.10.10.20.1130.200.2000 100.10.10.10.20.1330.200.2000 1 0,18 2 2200 100.10.10.10.20.930.200.2200 100.10.10.10.20.1130.200.2200 100.10.10.10.20.1330.200.2200 1 0,18 2 2400 100.10.10.10.20.930.200.2400 100.10.10.10.20.1130.200.2400 100.10.10.10.20.1330.200.2400 1 0,18 2 2600 100.10.10.10.20.930.200.2600 100.10.10.10.20.1130.200.2600 100.10.10.10.20.1330.200.2600 2 0,37 3 2800 100.10.10.10.20.930.200.2800 100.10.10.10.20.1130.200.2800 100.10.10.10.20.1330.200.2800 2 0,37 3 3000 100.10.10.10.20.930.200.3000 100.10.10.10.20.1130.200.3000 100.10.10.10.20.1330.200.3000 2 0,37 3 3200 100.10.10.10.20.930.200.3200 100.10.10.10.20.1130.200.3200 100.10.10.10.20.1330.200.3200 2 0,37 3 3400 100.10.10.10.20.930.200.3400 100.10.10.10.20.1130.200.3400 100.10.10.10.20.1330.200.3400 2 0,37 3 3600 100.10.10.10.20.930.200.3600 100.10.10.10.20.1130.200.3600 100.10.10.10.20.1330.200.3600 2 0,37 3 3800 100.10.10.10.20.930.200.3800 100.10.10.10.20.1130.200.3800 100.10.10.10.20.1330.200.3800 3 0,75 4 4000 100.10.10.10.20.930.200.4000 100.10.10.10.20.1130.200.4000 100.10.10.10.20.1330.200.4000 3 0,75 4 4200 100.10.10.10.20.930.200.4200 100.10.10.10.20.1130.200.4200 100.10.10.10.20.1330.200.4200 3 0,75 4 4400 100.10.10.10.20.930.200.4400 100.10.10.10.20.1130.200.4400 100.10.10.10.20.1330.200.4400 3 0,75 4 4600 100.10.10.10.20.930.200.4600 100.10.10.10.20.1130.200.4600 100.10.10.10.20.1330.200.4600 3 0,75 4 4800 100.10.10.10.20.930.200.4800 100.10.10.10.20.1130.200.4800 100.10.10.10.20.1330.200.4800 3 0,75 4 5000 100.10.10.10.20.930.200.5000 100.10.10.10.20.1130.200.5000 100.10.10.10.20.1330.200.5000 4 0,75 5 5200 100.10.10.10.20.930.200.5200 100.10.10.10.20.1130.200.5200 100.10.10.10.20.1330.200.5200 4 0,75 5 5400 100.10.10.10.20.930.200.5400 100.10.10.10.20.1130.200.5400 100.10.10.10.20.1330.200.5400 4 0,75 5 5600 100.10.10.10.20.930.200.5600 100.10.10.10.20.1130.200.5600 100.10.10.10.20.1330.200.5600 4 0,75 5 5800 100.10.10.10.20.930.200.5800 100.10.10.10.20.1130.200.5800 100.10.10.10.20.1330.200.5800 4 0,75 5 6000 100.10.10.10.20.930.200.6000 100.10.10.10.20.1130.200.6000 100.10.10.10.20.1330.200.6000 4 0,75 5
PALLET HANDLING CONVEYOR SYSTEMS
12
ROLLER CONVEYOR
ACCESSORIES DRIVE MODULE
1 2 3 100.10.10.10.90.100 . .
ORDER EXAMPLE: 100.10.10.10.90.930.037 Roller conveyor drive module for a conveyor with 930 mm between frames and drive power of 0,37 kW.
SPECIFICATIONS Structure 3 mm steel frame with zinc plated finish. External protection cover RAL 1021. Drive SEW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Power 0,18kW – payload up to 1500kg. Conveyor length up to 3600 mm.
0,37kW – payload up to 3000kg. Conveyor length up to 4800 mm. 0,75kW – payload up to 6000kg. Conveyor length up to 6000 mm.
Speed 12 m/min. Application Compatible with both roller to roller and tangential chain roller conveyors.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.100 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 DRIVE POWER (W)
180 | 370 | 750
REFERENCE NUMBER TABLE 7
POWER (W)
BETWEEN FRAMES
930 mm 1130 mm 1330 mm 180 100.10.10.10.90.100.930.180 100.10.10.10.90.100.1130.180 100.10.10.10.90.100.1330.180 370 100.10.10.10.90.100.930.370 100.10.10.10.90.100.1130.370 100.10.10.10.90.100.1330.370 750 100.10.10.10.90.100.930.750 100.10.10.10.90.100.1130.750 100.10.10.10.90.100.1330.750
PALLET HANDLING CONVEYOR SYSTEMS
13
ROLLER CONVEYOR
ACCESSORIES SUPPORTS
1 2 3 100.10.10.10.90.10 . .
ORDER EXAMPLE: 100.10.10.10.90.10.1130.400 Roller conveyor support for a conveyor with 1130 mm between frames and (TOR) top-of-roller height of 400+50 mm adjustment.
SPECIFICATIONS Structure Welded “C” shape profile. Standard coating RAL 9006. Other colors upon
request. Width Available for between frames of 930 mm, 1130 mm and 1330 mm. Height 350 mm up to 600 mm TOR (top-of-roller) with +50 mm adjustment.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.10 2 BETWEEN FRAME (mm)
930 | 1130 | 1330 3 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
REFERENCE NUMBER TABLE 8
HEIGHT (mm)
BETWEEN FRAMES
930 mm 1130 mm 1330 mm 350 100.10.10.10.90.10.930.350 100.10.10.10.90.10.1130.350 100.10.10.10.90.10.1330.350 400 100.10.10.10.90.10.930.400 100.10.10.10.90.10.1130.400 100.10.10.10.90.10.1330.400 450 100.10.10.10.90.10.930.450 100.10.10.10.90.10.1130.450 100.10.10.10.90.10.1330.450 500 100.10.10.10.90.10.930.500 100.10.10.10.90.10.1130.500 100.10.10.10.90.10.1330.500 550 100.10.10.10.90.10.930.550 100.10.10.10.90.10.1130.550 100.10.10.10.90.10.1330.550 600 100.10.10.10.90.10.930.600 100.10.10.10.90.10.1130.600 100.10.10.10.90.10.1330.600
DIMENSIONS BF BETWEEN FRAMES
PALLET HANDLING CONVEYOR SYSTEMS
14
500
1000
1500
2000
2500
3000
3500
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600
Load
(daN
)
Distance beetwen supports (mm)
ROLLER CONVEYOR
ACCESSORIES SUPPORTS
ROLLER CONVEYOR
LOAD/ DISTANCE BETWEEN SUPPORTS The following chart indicates the admissible static load for a set of two frames. The number of supports to be use in each case is determined by several factors such as load inertia, load distribution along conveyor or number of frame connections. Minimum of two supports per equipment. In case of doubt, please contact Antípoda.
PALLET HANDLING CONVEYOR SYSTEMS
15
ACCESSORIES WALKOVER PLATE
1 2 3 100.10.10.10.90.20 . .
ORDER EXAMPLE: 100.10.10.10.90.20.1130.175 Walkover plate for a roller conveyor with 1130 mm between frames and roller pitch of 175 mm.
SPECIFICATIONS Structure Anti-skid 3 mm plate with zinc plated finish. Max. 100Kg per walkover.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.20 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 ROLLER PITCH (mm)
150 | 175 | 200
REFERENCE NUMBER TABLE 9
PITCH (mm)
BETWEEN FRAMES
930 mm 1130 mm 1330 mm 150 100.10.10.10.90.20.930.150 100.10.10.10.90.20.1130.150 100.10.10.10.90.20.1330.150 175 100.10.10.10.90.20.930.175 100.10.10.10.90.20.1130.175 100.10.10.10.90.20.1330.175 200 100.10.10.10.90.20.930.200 100.10.10.10.90.20.1130.200 100.10.10.10.90.20.1330.200
DIMENSIONS BF BETWEEN FRAMES P ROLLER PITCH
PALLET HANDLING CONVEYOR SYSTEMS
16
ROLLER CONVEYOR
ACCESSORIES FIXED STOPPER
1 2 100.10.10.10.90.30 .
ORDER EXAMPLE: 100.10.10.10.90.30.1130 Fixed stopper for a roller conveyor with 1130 mm between frames.
SPECIFICATIONS Structure “C” shape profile with zinc plated finish. Payload Up to 1500 kg (full pallets).
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.30 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330
REFERENCE NUMBER TABLE 10
BETWEEN FRAMES
930 mm 1130 mm 1330 mm 100.10.10.10.90.30.930 100.10.10.10.90.30.1130 100.10.10.10.90.30.1330
DIMENSIONS BF BETWEEN FRAMES
PALLET HANDLING CONVEYOR SYSTEMS
17
ROLLER CONVEYOR
ACCESSORIES PNEUMATIC STOPPER
1 2 100.10.10.10.90.40 .
ORDER EXAMPLE: 100.10.10.10.90.40.1130 Pneumatic stopper for a roller conveyor with 1130 mm between frames.
SPECIFICATIONS Structure Zinc plated steel. Payload Up to 35 kg (empty pallets). Stroke 50 mm. 15 mm under the top of the roller when non-actuated and 35 mm
above top of the roller when actuated. Pneumatic actuation SMC CP96. Electro valve SMC 24VDC 5/2. Sensors Two SMC reed sensor switch, 3m fly lead. Ambient temperature 5oC to 50oC
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.40 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330
REFERENCE NUMBER TABLE 11
BETWEEN FRAMES
930 mm 1130 mm 1330 mm 100.10.10.10.90.40.930 100.10.10.10.90.40.1130 100.10.10.10.90.40.1330
DIMENSIONS BF BETWEEN FRAMES
PALLET HANDLING CONVEYOR SYSTEMS
18
ROLLER CONVEYOR
ACCESSORIES PNEUMATIC PUSHER
1 2 3 100.10.10.10.90.50 . .
ORDER EXAMPLE: 100.10.10.10.90.50.1130.150 Pneumatic pusher for a roller conveyor with 1130 mm between frames and roller pitch of 150 mm.
SPECIFICATIONS Structure Zinc plated steel. Payload Up to 35 kg (empty pallets). Stroke 200mm, 300 mm or 500 mm depending on conveyor width. Pneumatic actuation SMC CP96. Electro valve SMC 24VDC 5/2. Sensors Two SMC reed sensor switch, 3m fly lead. Ambient temperature 5oC to 50oC
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.50 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 PITCH (mm)
150 | 175 | 200
REFERENCE NUMBER TABLE 12
PITCH (mm)
BETWEEN FRAMES 930 mm 1130 mm 1330 mm
150 100.10.10.10.90.50.930.150 100.10.10.10.90.50.1130.150 100.10.10.10.90.50.1330.150 175 100.10.10.10.90.50.930.175 100.10.10.10.90.50.1130.175 100.10.10.10.90.50.1330.175 200 100.10.10.10.90.50.930.200 100.10.10.10.90.50.1130.200 100.10.10.10.90.50.1330.200
DIMENSIONS BF BETWEEN FRAMES
PALLET HANDLING CONVEYOR SYSTEMS
19
ROLLER CONVEYOR
ACCESSORIES ADJUSTABLE PHOTOCELL SUPPORT
1 100.10.10.10.90.60
ORDER EXAMPLE: 100.10.10.10.90.60 Roller conveyor single adjustable support for photoelectric sensor/reflector.
SPECIFICATIONS Structure Zinc plated steel. Compatibility Compatible with Sick GL6 type photoelectric sensors and Sick P250
reflectors. Sensor dimensions (W x H x D) 12 mm x 31.5 mm x 21 mm Refletor dimensions (W x H x D) 51.4 x 61 mm x 7.9 mm Sensor adjustment 115 mm to 195 mm distance to top-of-roller. Note When photoelectric sensors require reflectors, two supports must be
ordered.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.10.90.60
PALLET HANDLING CONVEYOR SYSTEMS
20
CHAIN CONVEYOR
Walkover Plates
100.10.10.20.90.20 - 26 -
Fixed Stopper 100.10.10.20.90.30
- 28 -
Supports 100.10.10.20.90.10
- 24 -
Pneumatic Stopper 100.10.10.20.90.40
- 29 –
Photocell Support 100.10.10.20.90.60
- 30 -
Transfer Link 100.10.10.20.90.80
- 33 –
Adjustable Side Guide
100.10.10.20.90.70 - 31 -
PALLET HANDLING CONVEYOR SYSTEMS
21
CHAIN CONVEYOR
1 2 3 4 100.10.10.20 . . .
ORDER EXAMPLE: 100.10.10.20.02.460.1300 Chain conveyor with 2 strands, distance between strands multiple of 460, conveyor length 1300 mm.
SPECIFICATIONS Structure 80x60 mm tube. Standard coating RAL 9006. Other colors upon request. Strands 2 and 3. Distance between strands 460 mm or 525 mm. Chain 10B-2 5/8” chain with straight side plates. Payload Up to 1,500 kg considering a 1200x800 mm pallet with a uniformly distributed
load. Maximum number of pallets on the conveyor as specified on TABLE 13 and TABLE 14.
Drive SEW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Speed 12 m/min. Inclined/Declined Not suitable. Horizontal application only. Direction Both. Supports Not included. See TABLE 15 and TABLE 16 on page 25. Ambient temperature 5oC to 50oC
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20 2 STRANDS
2 – 2 STRANDS 3 – 3 STRANDS
3 BETWEEN STRANDS (mm) 460 | 525
4 LENGTH (mm)
DIMENSIONS BS BETWEEN STRANDS L LENGTH
PALLET HANDLING CONVEYOR SYSTEMS
22
CHAIN CONVEYOR 2 STRANDS
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 25.
REFERENCE NUMBER TABLE 13
LEN
GTH
(mm
)
BETWEEN STRANDS
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
460 mm 525 mm 1300 100.10.10.20.02.460.1300 100.10.10.20.02.525.1300 1 0,55 2 1500 100.10.10.20.02.460.1500 100.10.10.20.02.525.1500 1 0,55 2 1600 100.10.10.20.02.460.1600 100.10.10.20.02.525.1600 1 0,55 2 1800 100.10.10.20.02.460.1800 100.10.10.20.02.525.1800 1 0,55 2 2000 100.10.10.20.02.460.2000 100.10.10.20.02.525.2000 1 0,55 2 2200 100.10.10.20.02.460.2200 100.10.10.20.02.525.2200 1 0,55 3 2400 100.10.10.20.02.460.2400 100.10.10.20.02.525.2400 2 0,75 3 2600 100.10.10.20.02.460.2600 100.10.10.20.02.525.2600 2 0,75 3 2800 100.10.10.20.02.460.2800 100.10.10.20.02.525.2800 2 0,75 3 3000 100.10.10.20.02.460.3000 100.10.10.20.02.525.3000 2 0,75 3 3200 100.10.10.20.02.460.3200 100.10.10.20.02.525.3200 2 0,75 3 3400 100.10.10.20.02.460.3400 100.10.10.20.02.525.3400 2 0,75 3 3600 100.10.10.20.02.460.3600 100.10.10.20.02.525.3600 2 0,75 3 3800 100.10.10.20.02.460.3800 100.10.10.20.02.525.3800 2 0,75 4 4000 100.10.10.20.02.460.4000 100.10.10.20.02.525.4000 2 0,75 4 4200 100.10.10.20.02.460.4200 100.10.10.20.02.525.4200 2 0,75 4 4400 100.10.10.20.02.460.4400 100.10.10.20.02.525.4400 2 0,75 4 4600 100.10.10.20.02.460.4600 100.10.10.20.02.525.4600 2 1,1 4 4800 100.10.10.20.02.460.4800 100.10.10.20.02.525.4800 2 1,1 4 5000 100.10.10.20.02.460.5000 100.10.10.20.02.525.5000 2 1,1 4 5200 100.10.10.20.02.460.5200 100.10.10.20.02.525.5200 2 1,1 4 5400 100.10.10.20.02.460.5400 100.10.10.20.02.525.5400 2 1,1 4 5600 100.10.10.20.02.460.5600 100.10.10.20.02.525.5600 2 1,1 5 5800 100.10.10.20.02.460.5800 100.10.10.20.02.525.5800 2 1,1 5 6000 100.10.10.20.02.460.6000 100.10.10.20.02.525.6000 2 1,1 5
PALLET HANDLING CONVEYOR SYSTEMS
23
CHAIN CONVEYOR 3 STRANDS
* Recommended number of supports for a uniformly distributed load over the pallets. For more details please see page 25.
REFERENCE NUMBER TABLE 14
LEN
GTH
(mm
)
BETWEEN STRANDS
Nº P
ALLE
TS
DR
IVE
POW
ER
(kW
)
* Nº S
UPP
OR
TS
460 mm 525 mm 1300 100.10.10.20.03.460.1300 100.10.10.20.03.525.1300 1 0,55 2 1500 100.10.10.20.03.460.1500 100.10.10.20.03.525.1500 1 0,55 2 1600 100.10.10.20.03.460.1600 100.10.10.20.03.525.1600 1 0,55 2 1800 100.10.10.20.03.460.1800 100.10.10.20.03.525.1800 1 0,55 2 2000 100.10.10.20.03.460.2000 100.10.10.20.03.525.2000 1 0,55 2 2200 100.10.10.20.03.460.2200 100.10.10.20.03.525.2200 1 0,55 3 2400 100.10.10.20.03.460.2400 100.10.10.20.03.525.2400 2 0,75 3 2600 100.10.10.20.03.460.2600 100.10.10.20.03.525.2600 2 0,75 3 2800 100.10.10.20.03.460.2800 100.10.10.20.03.525.2800 2 0,75 3 3000 100.10.10.20.03.460.3000 100.10.10.20.03.525.3000 2 0,75 3 3200 100.10.10.20.03.460.3200 100.10.10.20.03.525.3200 2 0,75 3 3400 100.10.10.20.03.460.3400 100.10.10.20.03.525.3400 2 0,75 3 3600 100.10.10.20.03.460.3600 100.10.10.20.03.525.3600 2 0,75 3 3800 100.10.10.20.03.460.3800 100.10.10.20.03.525.3800 2 0,75 4 4000 100.10.10.20.03.460.4000 100.10.10.20.03.525.4000 2 0,75 4 4200 100.10.10.20.03.460.4200 100.10.10.20.03.525.4200 2 0,75 4 4400 100.10.10.20.03.460.4400 100.10.10.20.03.525.4400 2 0,75 4 4600 100.10.10.20.03.460.4600 100.10.10.20.03.525.4600 2 1,1 4 4800 100.10.10.20.03.460.4800 100.10.10.20.03.525.4800 2 1,1 4 5000 100.10.10.20.03.460.5000 100.10.10.20.03.525.5000 2 1,1 4 5200 100.10.10.20.03.460.5200 100.10.10.20.03.525.5200 2 1,1 4 5400 100.10.10.20.03.460.5400 100.10.10.20.03.525.5400 2 1,1 4 5600 100.10.10.20.03.460.5600 100.10.10.20.03.525.5600 2 1,1 5 5800 100.10.10.20.03.460.5800 100.10.10.20.03.525.5800 2 1,1 5 6000 100.10.10.20.03.460.6000 100.10.10.20.03.525.6000 2 1,1 5
PALLET HANDLING CONVEYOR SYSTEMS
24
CHAIN CONVEYOR ACCESSORIES SUPPORTS
1 2 3 4 100.10.10.20.90.10 . . .
ORDER EXAMPLE: 100.10.10.20.90.10.03.525.600 Chain conveyor support for a conveyor with 3 strands, 525 mm between strands and (TOC) top-of-chain height of 600+50 mm adjustment.
SPECIFICATIONS Structure Welded “C” shape profile. Standard coating RAL 9006. Other colors upon
request. Width 920 or 1050 mm width for 2 and 3 strands chain conveyors. Height 350 mm up to 600 mm TOC (top-of-chain) with +50 mm adjustment.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.10 2 STRANDS
02 – 2 STRANDS 03 – 3 STRANDS
3 BETWEEN STRANDS (mm) 460 | 525
4 HEIGHT (mm) 350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS BS BETWEEN STRANDS
PALLET HANDLING CONVEYOR SYSTEMS
25
500
1000
1500
2000
2500
3000
3500
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600
Load
(daN
)
Distance beetwen supports (mm)
CHAIN CONVEYOR ACCESSORIES SUPPORTS
REFERENCE NUMBER TABLE 15
HEIGHT (mm)
2 STRANDS
BETWEEN STRANDS
460 mm 525 mm 350 100.10.10.20.90.10.02.460.350 100.10.10.20.90.10.02.525.350 400 100.10.10.20.90.10.02.460.400 100.10.10.20.90.10.02.525.400 450 100.10.10.20.90.10.02.460.450 100.10.10.20.90.10.02.525.450 500 100.10.10.20.90.10.02.460.500 100.10.10.20.90.10.02.525.500 550 100.10.10.20.90.10.02.460.550 100.10.10.20.90.10.02.525.550 600 100.10.10.20.90.10.02.460.600 100.10.10.20.90.10.02.525.600
REFERENCE NUMBER TABLE 16
HEIGHT (mm)
3 STRANDS
BETWEEN STRANDS
460 mm 525 mm 350 100.10.10.20.90.10.03.460.350 100.10.10.20.90.10.03.525.350 400 100.10.10.20.90.10.03.460.400 100.10.10.20.90.10.03.525.400 450 100.10.10.20.90.10.03.460.450 100.10.10.20.90.10.03.525.450 500 100.10.10.20.90.10.03.460.500 100.10.10.20.90.10.03.525.500 550 100.10.10.20.90.10.03.460.550 100.10.10.20.90.10.03.525.550 600 100.10.10.20.90.10.03.460.600 100.10.10.20.90.10.03.525.600
LOAD/ DISTANCE BETWEEN SUPPORTS The following chart indicates the admissible static load for a set of two frames. The number of supports to be use in each case is determined by several factors such as load inertia, load distribution along conveyor or number of frame connections. Minimum of two supports per equipment. In case of doubt, please contact Antípoda.
PALLET HANDLING CONVEYOR SYSTEMS
26
CHAIN CONVEYOR ACCESSORIES WALKOVER PLATE
1 2 3 4 100.10.10.20.90.20 . . .
ORDER EXAMPLE: 100.10.10.20.90.20.03.525.500 Walkover for a 3 strands chain conveyor, 525 mm between strands and 500 mm length.
SPECIFICATIONS Structure Anti-skid 3 mm plate with zinc plated finish. Max. 100Kg per walkover. Widths 300, 400 and 500 walkover width as standard. Other widths upon request.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.20 2 STRANDS
02 – 2 STRANDS 03 – 3 STRANDS
3
BETWEEN STRANDS (mm) 460 | 525
4 LENGTH (L) (mm) 300 | 400 | 500
DIMENSIONS BS BETWEEN STRANDS L LENGTH
PALLET HANDLING CONVEYOR SYSTEMS
27
CHAIN CONVEYOR ACCESSORIES WALKOVER PLATE
REFERENCE NUMBER TABLE 17
LENGTH (mm)
2 STRANDS
BETWEEN STRANDS
460 mm 525 mm 300 100.10.10.20.90.20.02.460.300 100.10.10.20.90.20.02.525.300 400 100.10.10.20.90.20.02.460.400 100.10.10.20.90.20.02.525.400 500 100.10.10.20.90.20.02.460.500 100.10.10.20.90.20.02.525.500
REFERENCE NUMBER TABLE 18
LENGTH (mm)
3 STRANDS
BETWEEN STRANDS
460 mm 525 mm 300 100.10.10.20.90.20.03.460.300 100.10.10.20.90.20.03.525.300 400 100.10.10.20.90.20.03.460.400 100.10.10.20.90.20.03.525.400 500 100.10.10.20.90.20.03.460.500 100.10.10.20.90.20.03.525.500
PALLET HANDLING CONVEYOR SYSTEMS
28
CHAIN CONVEYOR ACCESSORIES FIXED STOPPER
1 2 100.10.10.20.90.30 .
ORDER EXAMPLE: 100.10.10.20.90.30.525 Fixed stopper for a chain conveyor with side strand distance from center of 525 mm.
SPECIFICATIONS Structure “C” shape profile zinc plated finish. Payload Up to 1500 kg (full pallets).
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.30 2 BETWEEN STRANDS (mm)
460 | 525
REFERENCE NUMBER TABLE 19
BETWEEN STRANDS
460 mm 525 mm 100.10.10.20.90.30.460 100.10.10.20.90.30.525
DIMENSIONS BS BETWEEN STRANDS
PALLET HANDLING CONVEYOR SYSTEMS
29
CHAIN CONVEYOR ACCESSORIES PNEUMATIC STOPPER
1 2 3 100.10.10.20.90.40 . .
ORDER EXAMPLE: 100.10.10.20.90.40.03.525 Pneumatic stopper for a chain conveyor with 3 strands and side strand distance from center of 525 mm.
SPECIFICATIONS Structure Zinc plated steel. Payload Up to 35 kg (empty pallets). Stroke 50 mm. 15 mm under the top of the chain when non-actuated and 35 mm
above top of the chain when actuated. Pneumatic actuation SMC CP96. Electro valve SMC 24VDC 5/2. Sensors Two SMC reed sensor switch, 3m fly lead.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.40 2 STRANDS
02 – 2 STRANDS 03 – 3 STRANDS
3 BETWEEN STRANDS(mm) 460 | 525
REFERENCE NUMBER TABLE 20
STRANDS BETWEEN SRANDS
460 mm 525 mm 2 100.10.10.10.90.40.02.460 100.10.10.10.90.40.02.525 3 100.10.10.10.90.40.03.460 100.10.10.10.90.40.03.525
DIMENSIONS BS BETWEEN STRANDS
PALLET HANDLING CONVEYOR SYSTEMS
30
CHAIN CONVEYOR ACCESSORIES ADJUSTABLE PHOTOCELL SUPPORT
1 100.10.10.20.90.60
ORDER EXAMPLE: 100.10.10.20.90.60 Chain conveyor single support for photoelectric sensor/reflector.
SPECIFICATIONS Structure Zinc plated steel. Compatibility Compatible with Sick GL6 type photoelectric sensors and Sick P250
reflectors. Sensor dimensions (W x H x D) 12 mm x 31.5 mm x 21 mm Refletor dimensions (W x H x D) 51.4 x 61 mm x 7.9 mm Sensor adjustment 0 mm to 48 mm distance to top-of-chain. Note When photoelectric sensors require reflectors, two supports must be
ordered.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.60 2 LENGTH (L) (mm)
PALLET HANDLING CONVEYOR SYSTEMS
31
CHAIN CONVEYOR ACCESSORIES ADJUSTABLE SIDE GUIDE
1 2 100.10.10.20.90.70 .
ORDER EXAMPLE: 100.10.10.20.90.70.1500 Fixed side guide for a chain conveyor with 1500 mm long.
SPECIFICATIONS Structure “C” channel 33x30 with zinc plated finish. Other finishing upon request. Adjustment ±61,5 mm horizontal adjustment.
±24 mm vertical adjustment.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.70 2 LENGTH (mm)
DIMENSIONS BS BETWEEN STRANDS L LENGTH
PALLET HANDLING CONVEYOR SYSTEMS
32
CHAIN CONVEYOR ACCESSORIES ADJUSTABLE SIDE GUIDE
REFERENCE NUMBER TABLE 21 CONVEYOR
LENGTH (mm) 1300 100.10.10.20.90.70.1300 1500 100.10.10.20.90.70.1500 1600 100.10.10.20.90.70.1600 1800 100.10.10.20.90.70.1800 2000 100.10.10.20.90.70.2000 2200 100.10.10.20.90.70.2200 2400 100.10.10.20.90.70.2400 2600 100.10.10.20.90.70.2600 2800 100.10.10.20.90.70.2800 3000 100.10.10.20.90.70.3000 3200 100.10.10.20.90.70.3200 3400 100.10.10.20.90.70.3400 3600 100.10.10.20.90.70.3600 3800 100.10.10.20.90.70.3800 4000 100.10.10.20.90.70.4000 4200 100.10.10.20.90.70.4200 4400 100.10.10.20.90.70.4400 4600 100.10.10.20.90.70.4600 4800 100.10.10.20.90.70.4800 5000 100.10.10.20.90.70.5000 5200 100.10.10.20.90.70.5200 5400 100.10.10.20.90.70.5400 5600 100.10.10.20.90.70.5600 5800 100.10.10.20.90.70.5800 6000 100.10.10.20.90.70.6000
PALLET HANDLING CONVEYOR SYSTEMS
33
CHAIN CONVEYOR ACCESSORIES TRANSFER LINK
1 100.10.10.20.90.80
ORDER EXAMPLE: 100.10.10.20.90.80 Single chain transfer link (1 unit).
SPECIFICATIONS Structure Zinc plated steel.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.20.90.80
PALLET HANDLING CONVEYOR SYSTEMS
34
SINGLE LEVEL TRANSFER
Fixed Stopper - Rollers 100.10.10.30.90.20.11
- 36 -
Fixed Stopper - Chains 100.10.10.30.90.20.10
- 36 -
PALLET HANDLING CONVEYOR SYSTEMS
35
SINGLE LEVEL TRANSFER
1 2 3 100.10.10.30.10 . .
ORDER EXAMPLE: 100.10.10.30.10.03.600 Single level orthogonal transfer with 3-strand chain conveyor, transport height of 600 mm.
SPECIFICATIONS Structure Steel frame. Standard coating RAL 9006. Other colors upon request. Dimensions 1450x1291 mm (LxW). Height 450mm to 600mm, with ± 15 mm mechanical adjustment. Payload Up to 1,500 kg load. Roller conveyor drive SEW 0,55kW / 400V / 50Hz / 3 phase rated voltage, IP55, CE. Roller pitch 180 mm. Roller conveyor speed 12 m/min. Chain conveyor drive SEW 0,37kW / 400V / 50Hz / 3 phase rated voltage, IP55, CE. Chain side strand distance from center
540 mm.
Chain conveyor speed 12 m/min. Vertical movement drive SEW 0,55kW / 400V / 50Hz / 3 phase rated voltage, IP55, CE. Lifting time 2 sec. Inclined/Declined Not suitable. Horizontal application only. Sensors Supports compatible with Sick IME12 included. Sensors included. Electrical connections ILME industrial connectors 3x3P+PE drive connector and 1x4+4P+PE
sensor connector. Ambient temperature 5oC to 50oC.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.30.10 2 CHAIN STRANDS
02 – 2 STRANDS 03 – 3 STRANDS
3 HEIGHT (mm) 450 | 500 | 550 | 600
REFERENCE NUMBER TABLE 22
HEIGTH (mm) Nº OF STRANDS 2 STRANDS 3 STRANDS
450 100.10.10.30.02.450 100.10.10.30.03.450 500 100.10.10.30.02.500 100.10.10.30.03.500 550 100.10.10.30.02.550 100.10.10.30.03.550 600 100.10.10.30.02.600 100.10.10.30.03.600
PALLET HANDLING CONVEYOR SYSTEMS
36
SINGLE LEVEL TRANSFER ACCESSORIES FIXED STOPPER
1 2 100.10.10.30.90.20 .
ORDER EXAMPLE: 100.10.10.30.90.20.10 Fixed stopper for chains.
100.10.10.30.90.20.10 - Fixed stopper for chains
100.10.10.30.90.20.11 - Fixed stopper for rollers
SPECIFICATIONS Structure Zinc plated steel.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.30.90.20 2 STRANDS
10 – FIXED STOPPER - CHAINS 11 – FIXED STOPPER - ROLLERS
PALLET HANDLING CONVEYOR SYSTEMS
37
RAIL GUIDED VEHICLE
End Stoppers 100.10.10.40.90.20
- 41 -
Rails 100.10.10.40.90.10
- 40 -
PALLET HANDLING CONVEYOR SYSTEMS
38
RAIL GUIDED VEHICLE
ROLLER CONVEYOR
1 2 3 4 5 100.10.10.40.10 . . . .
ORDER EXAMPLE: 100.10.10.40.10.1130.150.1500.350 RGV with roller conveyor 1130 mm between frames, 150 mm roller pitch, 1500 mm conveyor, (TOR) top-of-roller of 350+50 mm height.
SPECIFICATIONS Structure Steel frame. Standard coating RAL 9006. Other colors upon request. Height 350 mm up to 600 mm TOR (top-of-roller) with +50 mm adjustment. Payload Up to 1,500 kg load. Roller pitch 150 mm. Roller transmission Roller to roller. Drive – roller conveyor SEW 0,37kW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Conveyor speed 12 m/min. Drive – RGV SEW 0,25kW 400V / 50Hz / 3 phase rated voltage with brake, IP55, CE. RGV speed Up to 30m/min. Max. acceleration/deceleration 0,25 m/s2. Inclined/Declined Not suitable. Horizontal application only. Automation Automation not included. Inverter and brake resistor required. Cable carrier Cable carrier not included. Ambient temperature 5oC to 50oC.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.40.10 2 WIDTH (mm)
930 | 1130 | 1330 - BETWEEN FRAMES 3 PITCH (mm)
150 4 CONVEYOR LENGTH (mm)
1500 5 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS BF BETWEEN FRAMES L CONVEYOR LENGTH W RGV WIDTH
PALLET HANDLING CONVEYOR SYSTEMS
39
RAIL GUIDED VEHICLE ROLLER CONVEYOR
REFERENCE NUMBER TABLE 23
HEIG
HT
(mm
)
150 ROLLER PITCH (mm)
BS=930 mm BS=1130 mm BS=1330 mm 350 100.10.10.40.10.930.1500.150.350 100.10.10.40.10.1130.1500.150.350 100.10.10.40.10.1330.1500.150.350 400 100.10.10.40.10.930.1500.150.400 100.10.10.40.10.1130.1500.150.400 100.10.10.40.10.1330.1500.150.400 450 100.10.10.40.10.930.1500.150.450 100.10.10.40.10.1130.1500.150.450 100.10.10.40.10.1330.1500.150.450 500 100.10.10.40.10.930.1500.150.500 100.10.10.40.10.1130.1500.150.500 100.10.10.40.10.1330.1500.150.500 550 100.10.10.40.10.930.1500.150.550 100.10.10.40.10.1130.1500.150.550 100.10.10.40.10.1330.1500.150.550 600 100.10.10.40.10.930.1500.150.600 100.10.10.40.10.1130.1500.150.600 100.10.10.40.10.1330.1500.150.600
PALLET HANDLING CONVEYOR SYSTEMS
40
RAIL GUIDED VEHICLE ACCESSORIES RAILS
1 2 3 100.10.10.40.90.10 . .
ORDER EXAMPLE: 100.10.10.40.90.10.01.1000 Rail for RGV with length of 1000 mm, to be installed at the rail end.
SPECIFICATIONS Structure Steel tube. Zinc plated finish.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.40.90.10 2 MOUNTING TYPE
01 – END 11 – MIDDLE
3 LENGTH (mm) 1000 | 2000 | 3000
REFERENCE NUMBER TABLE 24
MO
UNTI
NG
TYPE
RAIL LENGTH (mm)
1000 2000 3000 END 100.10.10.40.90.10.01.1000 100.10.10.40.90.10.01.2000 100.10.10.40.90.10.01.3000
MIDDLE 100.10.10.40.90.10.11.1000 100.10.10.40.90.10.11.2000 100.10.10.40.90.10.11.3000
DIMENSIONS BF BETWEEN FRAMES W RGV WIDTH
PALLET HANDLING CONVEYOR SYSTEMS
41
RAIL GUIDED VEHICLE ACCESSORIES END STOPPERS
1 100.10.10.40.20
ORDER EXAMPLE: 100.10.10.40.20 One end stopper to be installed at the end of the RGV rail.
SPECIFICATIONS Structure Welded structure with zinc plated finish.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.40.90.20
PALLET HANDLING CONVEYOR SYSTEMS
42
TURNTABLE
ROLLER CONVEYOR
1 2 3 4 5 6 100.10.10.50.10 . . . . .
RDER EXAMPLE: 100.10.10.50.10.1130.150.1500.600.1 Turntable with roller conveyor 1130 mm between frames, 150 mm roller pitch, 1500 mm conveyor length, (TOR) top-of-roller of 600+50 mm height, including security side cover.
SPECIFICATIONS Structure Steel frame. Standard coating RAL 9006. Other colors upon request. Security side cover As optional. Height 350 mm up to 600 mm TOR (top-of-roller) with +50 mm adjustment. Payload Up to 1,500 kg load. Roller pitch 150 mm. Roller transmission Roller to roller. Drive – roller conveyor SEW 0,37kW 400V / 50Hz / 3 phase rated voltage, IP55, CE. Conveyor speed 12 m/min. Drive – turntable rotation SEW 0,37kW 400V / 50Hz / 3 phase rated voltage with brake, IP55, CE. Rotation speed 2,6 1/min. Direction CW and CCW. Stop position -90o to +90o. Inclined/Declined Not suitable. Horizontal application only. Sensors Supports compatible with Sick IME18 included. Sensors included. Ambient temperature 5oC to 50oC
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.10.50.10 2 BETWEEN FRAMES (mm)
930 | 1130 | 1330 3 PITCH (mm)
150 4 CONVEYOR LENGTH (mm)
1500 5 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600 6 SECURITY SIDE COVER
0 – NO SIDE COVER 1 – WITH SIDE COVER
PALLET HANDLING CONVEYOR SYSTEMS
43
TURNTABLE ROLLER CONVEYOR
REFERENCE NUMBER TABLE 25
HEIG
HT
(mm
)
TURNTABLE – ROLLER CONVEYOR WITHOUT SECURITY SIDE COVER
150 ROLLER PITCH (mm)
BS=930 mm BS=1130 mm BS=1330 mm 350 100.10.10.50.10.930.1500.150.350.0 100.10.10.50.10.1130.1500.150.350.0 100.10.10.50.10.1330.1500.150.350.0 400 100.10.10.50.10.930.1500.150.400.0 100.10.10.50.10.1130.1500.150.400.0 100.10.10.50.10.1330.1500.150.400.0 450 100.10.10.50.10.930.1500.150.450.0 100.10.10.50.10.1130.1500.150.450.0 100.10.10.50.10.1330.1500.150.450.0 500 100.10.10.50.10.930.1500.150.500.0 100.10.10.50.10.1130.1500.150.500.0 100.10.10.50.10.1330.1500.150.500.0 550 100.10.10.50.10.930.1500.150.550.0 100.10.10.50.10.1130.1500.150.550.0 100.10.10.50.10.1330.1500.150.550.0 600 100.10.10.50.10.930.1500.150.600.0 100.10.10.50.10.1130.1500.150.600.0 100.10.10.50.10.1330.1500.150.600.0
REFERENCE NUMBER TABLE 26
HEIG
HT
(mm
)
TURNTABLE – ROLLER CONVEYOR WITH SECURITY SIDE COVER
150 ROLLER PITCH (mm)
BS=930 mm BS=1130 mm BS=1330 mm 350 100.10.10.50.10.930.1500.150.350.1 100.10.10.50.10.1130.1500.150.350.1 100.10.10.50.10.1330.1500.150.350.1 400 100.10.10.50.10.930.1500.150.400.1 100.10.10.50.10.1130.1500.150.400.1 100.10.10.50.10.1330.1500.150.400.1 450 100.10.10.50.10.930.1500.150.450.1 100.10.10.50.10.1130.1500.150.450.1 100.10.10.50.10.1330.1500.150.450.1 500 100.10.10.50.10.930.1500.150.500.1 100.10.10.50.10.1130.1500.150.500.1 100.10.10.50.10.1330.1500.150.500.1 550 100.10.10.50.10.930.1500.150.550.1 100.10.10.50.10.1130.1500.150.550.1 100.10.10.50.10.1330.1500.150.550.1 600 100.10.10.50.10.930.1500.150.600.1 100.10.10.50.10.1130.1500.150.600.1 100.10.10.50.10.1330.1500.150.600.1
PALLET HANDLING CONVEYOR SYSTEMS
44
TURNTABLE ROLLER CONVEYOR
TURNTABLE DIMENSIONS TABLE 27
TURNTABLE DIMENSIONS
BF 930 mm 1130 mm 1330 mm ØD 1968 mm 2168 mm 2368 mm
DIMENSIONS BF BETWEEN FRAMES ØD TURNTABLE DIAMETER
DIMENSIONS BF BETWEEN FRAMES ØD TURNTABLE DIAMETER
PALLET HANDLING CONVEYOR SYSTEMS
45
PALLET STACK GUIDE FIXED
1 2 3 100.10.90.20.10 . .
ORDER EXAMPLE: 100.10.90.20.10.800.600 Fixed stack guide with a capacity for 15 pallets with 800mm width, transport height of 600 mm.
SPECIFICATIONS Structure Powder coated steel frame. Standard coating RAL 9006. Other colors upon
request Pallet sizes 800x1200 mm, 1000x1200 mm and 1200x1200 mm. Pallet infeed/outfeed Longitudinal, short side leading. Width Accordingly to pallet width. Pallet Capacity Up to 15 pallets Roller conveyor Not included. Conveyor must be selected according with working height and
pallet size.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.90.20.10 2 PALLET WIDTH (mm)
800 | 1000 | 1200 3 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS W PALLET WIDTH H TRANSPORT HEIGHT
PALLET HANDLING CONVEYOR SYSTEMS
46
PALLET STACK GUIDE FIXED
REFERENCE NUMBER TABLE 28 HEIGHT
(mm) PALLET DIMENSION
800X1200 1000X1200 1200X1200 350 100.10.90.20.10.800.350 100.10.90.20.10.1000.350 100.10.90.20.10.1200.350 400 100.10.90.20.10.800.400 100.10.90.20.10.1000.400 100.10.90.20.10.1200.400 450 100.10.90.20.10.800.450 100.10.90.20.10.1000.450 100.10.90.20.10.1200.450 500 100.10.90.20.10.800.500 100.10.90.20.10.1000.500 100.10.90.20.10.1200.500 550 100.10.90.20.10.800.550 100.10.90.20.10.1000.550 100.10.90.20.10.1200.550 600 100.10.90.20.10.800.600 100.10.90.20.10.1000.600 100.10.90.20.10.1200.600
PALLET HANDLING CONVEYOR SYSTEMS
47
PALLET STACK GUIDE ADJUSTABLE
1 2 3 100.10.90.20.20 . .
ORDER EXAMPLE: 100.10.90.20.20.800.600 Adjustable Pallet dispenser with a capacity for 15 pallets with 800mm width, transport height of 600 mm.
SPECIFICATIONS Structure Powder coated steel frame. Standard coating RAL 9006. Other colors upon
request Pallet sizes 800x1200 mm, 1000x1200 mm and 1200x1200 mm. Pallet infeed/outfeed Longitudinal, short side leading. Width Accordingly to pallet width. Pallet Capacity Up to 15 pallets Roller conveyor Not included. Conveyor must be selected according with working height and
pallet size. Pneumatic actuation SMC CP96. Pneumatic horizontal stroke 200 mm. Control Manual valve. Sensors No sensor included. Ambient temperature 5oC to 50oC.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.90.20.20 2 MINIMUM PALLET WIDTH (mm)
800 | 1000 | 1200 3 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS W PALLET WIDTH H TRANSPORT HEIGHT
PALLET HANDLING CONVEYOR SYSTEMS
48
PALLET STACK GUIDE ADJUSTABLE
REFERENCE NUMBER TABLE 29 HEIGHT
(mm) PALLET WIDTH
800 / 1000 1000 / 1200 350 100.10.90.20.20.800.350 100.10.90.20.20.1000.350 400 100.10.90.20.20.800.400 100.10.90.20.20.1000.400 450 100.10.90.20.20.800.450 100.10.90.20.20.1000.450 500 100.10.90.20.20.800.500 100.10.90.20.20.1000.500 550 100.10.90.20.20.800.550 100.10.90.20.20.1000.550 600 100.10.90.20.20.800.600 100.10.90.20.20.1000.600
PALLET HANDLING CONVEYOR SYSTEMS
49
PALLET STACKER/DESTACKER 10/15 PALLETS
1 2 3 4
100.10.90.20.20 . . . ORDER EXAMPLE: 100.10.90.40.15.800.1200.600 Pallet dispenser with a capacity of 15 pallets with 800mm width and 1200mm long, transport height of 600 mm.
SPECIFICATIONS Structure Steel frame. Standard coating RAL 9006. Other colors upon request. Pallet sizes 800x1200 mm, 1000x1200 mm and 1200x1200 mm. Pallet infeed/outfeed Longitudinal, short side leading. Roller conveyor Not included. Conveyor must be selected according with working height and
pallet size. Pneumatic actuation SMC C95 + SMC CD85. Electro valve 4x SMC SY5300-5U1 + 1x SMC SY5200-5U1. Sensors 12x SMC D-M9PZ. Automation Not included. Supplied with electrical cabinet including pre-wiring installation. Ambient temperature 5oC to 50oC.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.90.40 2 PALLET CAPACITY (UNITS)
10 | 15 3 PALLET WIDTH (mm)
800 | 1000 | 1200 4 PALLET LENGTH (mm)
1200 5 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS W PALLET WIDTH L PALLET LENGTH H TRANSPORT HEIGHT
10P HEIGHT FOR 10 PALLETS 15P HEIGHT FOR 15 PALLETS
PALLET HANDLING CONVEYOR SYSTEMS
50
PALLET STACKER/DESTACKER
REFERENCE NUMBER TABLE 30
HEIGHT (mm)
PALLET CAPACITY - 10 PALLET DIMENSIONS
800X1200 1000X1200 1200X1200 350 100.10.90.40.10.800.350 100.10.90.40.10.1000.350 100.10.90.40.10.1200.350 400 100.10.90.40.10.800.400 100.10.90.40.10.1000. 400 100.10.90.40.10.1200.400 450 100.10.90.40.10.800. 450 100.10.90.40.10.1000. 450 100.10.90.40.10.1200. 450 500 100.10.90.40.10.800. 500 100.10.90.40.10.1000. 500 100.10.90.40.10.1200. 500 550 100.10.90.40.10.800. 550 100.10.90.40.10.1000. 550 100.10.90.40.10.1200. 550 600 100.10.90.40.10.800. 600 100.10.90.40.10.1000. 600 100.10.90.40.10.1200. 600
REFERENCE NUMBER TABLE 31
HEIGHT (mm)
PALLET CAPACITY - 15 PALLET DIMENSIONS
800X1200 1000X1200 1200X1200 350 100.10.90.40.15.800.350 100.10.90.40.15.1000. 350 100.10.90.40.15.1200.350 400 100.10.90.40.15.800. 400 100.10.90.40.15.1000. 400 100.10.90.40.15.1200. 400 450 100.10.90.40.15.800. 450 100.10.90.40.15.1000. 450 100.10.90.40.15.1200. 450 500 100.10.90.40.15.800. 500 100.10.90.40.15.1000. 500 100.10.90.40.15.1200. 500 550 100.10.90.40.15.800. 550 100.10.90.40.15.1000. 550 100.10.90.40.15.1200. 550 600 100.10.90.40.15.800. 600 100.10.90.40.15.1000. 600 100.10.90.40.15.1200. 600
PALLET HANDLING CONVEYOR SYSTEMS
51
FORKLIFT BUMPER
1 2 100.10.90.10 .
ORDER EXAMPLE: 100.10.90.10.800 Forklift bumper for pallets with 800mm width.
SPECIFICATIONS Structure Welded tube. Standard coating RAL 9006. Other colors upon request.
Front bumper zinc-plated with a rubber stop. Width Accordingly to pallet width. Height 350 mm up to 600mm of the TOR/TOC (top-of-roller/chain) height, with a 50
mm interval.
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.90.10 2 PALLET WIDTH (mm)
800 | 1000 | 1200
DIMENSIONS W PALLET WIDTH H TOR/TOC (top-of-
roller/chain) HEIGHT
REFERENCE NUMBER TABLE 32
PALLET WIDTH (W) 800 1000 1200
100.10.90.30.800 100.10.90.30.1000 100.10.90.30.1200
PALLET HANDLING CONVEYOR SYSTEMS
52
FORKLIFT GUIDES FOR PALLETS
1 2 3 100.10.90.30 . .
ORDER EXAMPLE: 100.10.90.30.1000.450 Forklift guides for pallets 1000mm width and conveyed at TOR (top-of-roller) height of 450mm.
SPECIFICATIONS Structure Welded structure with zinc plated finish. Width Accordingly to pallet width. Height 350 mm up to 600mm of the TOR/TOC (top-of-roller/chain) height, with a 50
mm interval. Adjustment ±30 mm horizontal mechanical adjustment. Sensors Not included, only upon request. Sensor dimensions (W x H x D) 12 mm x 31.5 mm x 21 mm Refletor dimensions (W x H x D) 51.4 x 61 mm x 7.9 mm Sensor adjustment 0 mm to 58 mm horizontal adjustment
CONFIGURATOR Reference number according to the following configuration. 1 TYPE
100.10.90.30 2 PALLET WIDTH (mm)
800 | 1000 | 1200 3 HEIGHT (mm)
350 | 400 | 450 | 500 | 550 | 600
DIMENSIONS W PALLET WIDTH
H TOR/TOC (top-of-roller/chain) HEIGHT
PALLET HANDLING CONVEYOR SYSTEMS
53
FORKLIFT GUIDES FOR PALLETS
REFERENCE NUMBER TABLE 33
HEIGHT (H)
PALLET WIDTH (W) 800 1000 1200
350 100.10.90.30.800.350 100.10.90.30.1000.350 100.10.90.30.1200.350 400 100.10.90.30.800.400 100.10.90.30.1000.400 100.10.90.30.1200.400 450 100.10.90.30.800.450 100.10.90.30.1000.450 100.10.90.30.1200.450 500 100.10.90.30.800.500 100.10.90.30.1000.500 100.10.90.30.1200.500 550 100.10.90.30.800.550 100.10.90.30.1000.550 100.10.90.30.1200.550 600 100.10.90.30.800.600 100.10.90.30.1000.600 100.10.90.30.1200.600
PALLET HANDLING CONVEYOR SYSTEMS
54
INDEX
100.10.10.10.10 .......................................................................................................................................... 4 100.10.10.10.20 .......................................................................................................................................... 8 100.10.10.10.90.10 .................................................................................................................................. 13 100.10.10.10.90.100 ................................................................................................................................ 12 100.10.10.10.90.20 .................................................................................................................................. 15 100.10.10.10.90.30 .................................................................................................................................. 16 100.10.10.10.90.40 .................................................................................................................................. 17 100.10.10.10.90.50 .................................................................................................................................. 18 100.10.10.10.90.60 .................................................................................................................................. 19 100.10.10.20 ............................................................................................................................................. 21 100.10.10.20.90.10 .................................................................................................................................. 24 100.10.10.20.90.20 .................................................................................................................................. 26 100.10.10.20.90.30 .................................................................................................................................. 28 100.10.10.20.90.40 .................................................................................................................................. 29 100.10.10.20.90.60 .................................................................................................................................. 30 100.10.10.20.90.70 .................................................................................................................................. 31 100.10.10.30 ............................................................................................................................................. 35 100.10.10.40.10 ........................................................................................................................................ 38 100.10.10.40.90.10 .................................................................................................................................. 40 100.10.10.40.90.20 .................................................................................................................................. 41 100.10.10.50.10 ........................................................................................................................................ 42 100.10.90.10 ............................................................................................................................................. 51 100.10.90.20.10 ........................................................................................................................................ 45 100.10.90.20.20 ........................................................................................................................................ 47 100.10.90.30 ............................................................................................................................................. 52 100.10.90.40 ............................................................................................................................................. 49 Chain conveyor ......................................................................................................................................... 21
2 strands ................................................................................................................................................ 22 3 strands ................................................................................................................................................ 23 Fixed stopper ......................................................................................................................................... 28 Photoelectric support sensor .............................................................................................................. 30 Pneumatic stopper ............................................................................................................................... 29 Side guide .............................................................................................................................................. 31 Supports ................................................................................................................................................. 24 Transfer link ..................................................................................................................................... 33, 36 Walkover plate ...................................................................................................................................... 26
Forklift bumper .......................................................................................................................................... 51 Forklift guide for pallets ........................................................................................................................... 52 Pallet stack guide
Adjustable .............................................................................................................................................. 47 Fixed ....................................................................................................................................................... 45
Pallet stacker/destacker .......................................................................................................................... 49 Pitch
150mm, Roller to roller transmission ................................................................................................... 5 150mm, Tangential chain transmission .............................................................................................. 9 175 mm, Tangential chain transmission ........................................................................................... 10 175mm, Roller to roller transmission ................................................................................................... 6
PALLET HANDLING CONVEYOR SYSTEMS
55
200 mm, Tangential chain transmission ........................................................................................... 11 200mm, Roller to roller transmission ................................................................................................... 7
Rail guided vehicle ................................................................................................................................... 38 End stopper ........................................................................................................................................... 41 Rails ........................................................................................................................................................ 40
Roller conveyor Drive module ......................................................................................................................................... 12 Fixed stopper ......................................................................................................................................... 16 Photoeletric sensor support ................................................................................................................ 19 Pneumatic pusher ................................................................................................................................. 18 Pneumatic stopper ............................................................................................................................... 17 Roller to roller transmission .................................................................................................................. 4 Supports ................................................................................................................................................. 13 Tangential chain transmission .............................................................................................................. 8 Walkover plate ...................................................................................................................................... 15
Single level transfer .................................................................................................................................. 35 Turntable
Roller conveyor ..................................................................................................................................... 42
ANTÍPODA Rua Julieta Ubaldina Miranda, nº106 Lote 17 4470-441 Maia, Portugal Tel. +351 22 953 54 37 [email protected] www.antipoda.eu