A983OWNER'S MANUALASSEMBLY INSTRUCTIONS

S MMITH ACHINE

A. Safety Instructions:

˙ Read all cautions/warnings and obtain proper instruction on use of the machinesprior to using. Use appropriate positioning and controlled movements.

˙

˙

˙

˙

˙

˙

˙

˙

˙

˙

˙

˙

Assemble and operate the machine on a solid, level surface. DO NOT useoutdoors or near water.

Never allow children on or near the machine.

Make sure all fasteners are properly tightened for safety. DO NOT use themachine if the unit is disassembled in any way.

Keep head, limbs, and fingers clear of all moving parts.

If at any time during exercise you feel faint, dizzy or experience pain, stop andconsult you physician.

DO NOT wear loose or dangling clothing while using the equipment. Keep awayfrom all moving parts.

Use care when mounting and dismounting the unit.

DO NOT use any accessories that aren't specifically recommended by themanufacturer. These might cause injuries or cause the unit to fall.

Close supervision is necessary when this machine is used by, on, or nearadolescent, invalids, and disabled persons.

Use this machine only for its intended use as described in this manual.

Never operate this machine if it has been damaged in any way. If it is not workingproperly, been dropped or damaged, contact your dealer. DO NOT attempt to fix abroken or jammed machine. Notify floor staff.

Never drop or insert any object into any opening.

1

2

B. Introduction

Pulley

Main frame

Pulley holder

Sliding rod

Hook

Bullet end cap B

Set springs

Elevation connector

Linear bearing sleeve

Foot pad

Rear frame

Connector A

Covers

Hook plate

Lifting rod

Guide bushing

Weight plate rod

Bullet end cap A

Connector B

Stack Track

Weight stack

Safety pad

C. List of Parts

1.Two main frames

2.One connector A

3.One connector B

4.Two pulley holders

5.Eight weight plate rods

6.One lifting rod

7.Two bullet end caps B

8.Two set springs

9.One L shaped hex key wrench M4

10.One L shaped hex key wrench M5

11.One L shaped hex key wrench M6

12.One L shaped hex key wrench M10

13.One double-end open wrench 8mm*17mm

14.One double-end open wrench 12mm*15mm

3

1. Pulley holder-Right

2. Elevation connector set-Right

3. Assembly parts package *2

4. Main frame *2

5. Lifting rod

6. Connector A

7. Rear Frame-Right

8. Pulley holder-Left

9. Connector B

10. Rear Frame-Left

11. Weight plate rod *8

12. Elevation connector set-Left

13. Weight stack *2

14. Cover *4

4

D. Assembly Instruction

Installation of Rear Frame

Step 1: Secure left rear frame onto the left frame as shown.

Step 2: Repeat step 1 for right frame assembly.

NutsFlat washerSpring washerScrews

5

6

Installation of Connector A & B

Step 1: Secure left and right rear frames with connector B as shown below.

NutsFlat washerSpring washerScrews

NutsWasherFixing plateSpring washerScrews

ScrewsSpring washerFlat washerNuts

ScrewsSpring washerFixing plateWasherNuts

Step 2: Secure left and right main frames with connector A as shown below.

7

Weight plate rod installation (8 rods as shown)

Step 1: Insert the weight plate rod into the rear frame as shown.

Step 2: Secure with screws provided.

Step 3: Repeat step1-2 for installation of the other 7 weight plate rods.

8

Installation of lifting rod

Step 1: Put the lifting rod horizontally through the gap between the sliding rod and hookplate on both sides.

Step 2: Hang the lifting rod onto the hook plate. The recommended height is from the4 to the 6 shelf.

Step 3: Secure left and right elevation connectors onto the handlebars.

Caution: parts are specific to right and left sides. Please identify parts as being for leftor right side before installation.

th th

9

Step 4: Pull the linear bearing sleeves up and secure the parts with the elevationconnectors on both sides as shown below.

Flat washerSpring washerScrewsFlat washerSpring washerScrews

Flat washerSpring washerScrews

Flat washer

ScrewsSpring washer

Step 5: Follow the instructions below to assemble the parts provided:

1.Assemble the plastic part provided onto the lifting rod handlebars.

2.Secure washers and screws.

3.Secure bullet end caps.

4.Secure the set springs.

10

Installation of cables and weight stacks

Step 1: Loosen screws before removing covers.

Step 2: Identify pulley assemblies as to left and right.

Step 3: Secure pulley assemblies with the frame on both sides.

11

Step 4: Release the right side weight stack bands.

Step 5: Pull the right side weight stack up just above M (the hole on the stack track),then use the tools provided to go through M to hold the stack.(Caution: Be careful not to pinch your fingers and hands.)

Step 6: Hang the lifting rod on the highest shelf.

12

Step 7: Put the cable right through E, F, and G as shown.

Step 8: Secure the cable with nuts after the cable goes through H as shown.

13

Step 9: Remove the tools.

Step 10: Repeat steps 4-9 to install the left side.

Step 11: Secure covers onto the frame.

Step 12: Test if the lifting rod can go up and down smoothly.

Note: The length between the left and right side frame should range from1490-1497 cm as shown.

14

Test tip for left and right side frame assembly:

Step 1. After completing the assembly, please hang the lifting rod on the top shelf.Does the hook fit in the hook plate? Then hang the lifting rod on thebottom shelf. Does the hook fit in place?

Step 2. If not, please the foot tube to let the hook fit on the hook plateas shown.

perfectlyperfectly

adjust perfectly

15

after adjustmentBefore adjustment

Foot tube

hook plate

hook

Cautions:

The guiding sets "A" & "B" should stick to the hook plate while in operation. Improperplacement would not only damage the machine, but also lose its intended efficacy ofprotection.

16

E.MAINTENANCE SCHEDULE(A983) Maintenance Schedule

1

2

3

4

Clean.

Inspect for looseness.Tighten if needed.

Wipe clean with a damp cloth.

Exterior

Screws

Guide rod

Cable Inspect for wear andbreakage.

17

Like cars, fitness products require maintenance. Regular maintenance extendsproduct life, and failure to maintain products can void the manufacturer's warranty.Copy the maintenance log sheet, and record maintenance work for each fitnessproduct.

1. Use a clean, lint-free towel, dampened with a mixture of Simple Green all-purposecleaner and water, to thoroughly clean the product exterior.

2. Inspect parts for looseness, and secure all loose screws. Make sure that theproduct is safe for operation. If safety issues arise, place an "Out of Order" sign onthe product, and call for service.

3.

Please follow standard safety precautions when working on this product.Do NOT use cleaners with alcohol, ammonia, or other damaging chemicals. The useof such chemicals can damage the product and void the warranty. Never spray orpour any liquid directly onto the product. Doing so can damage electroniccomponents and void the warranty.

This product has moving parts that can be hazardous. Exercise caution whenmaintaining, operating, or moving this product.

Daily tasks

Caution

Clean guide rods. Use a clean, lint-free towel, dampened with a mixture of SimpleGreen all-purpose cleaner and water. Apply a small amount of silicone lubricantonto the guide rods.

1.Inspect belts or cables (as applicable) for wear and breakage. Replace belts onceevery four years.

Weekly tasks

‧

‧

R

R

F.MAINTENANCE TASK LIST (STRENGTH PRODUCTS):

18

G.MAINTENANCE ONE-YEAR MAINTENANCE LOG:

Daily Tasks

Notes:

Facility : Supervisor:

Product Model Number : Serial Number:

Start Date: End Date:

Weeks 1-7 Weeks 8-14 Weeks 15-21 Weeks 22-28Completed

Daily Tasks Weeks 29-35 Weeks 36-42 Weeks 43-49 Weeks 50-52

Weeks 1-7 Weeks 8-14 Weeks 15-21 Weeks 22-28CompletedWeekly Tasks

1 2 3 4 5 6 7 8 9CompletedMonthly Tasks

Completed

Weeks 29-35 Weeks 36-42 Weeks 43-49 Weeks 50-52CompletedWeekly Tasks

10 11 12

Quarter 1 Quarter 2 Quarter 3 Quarter 4Completed

Year 1CompletedYearly Tasks

Quarterly Tasks

19