99-787399-7873 kit assembly 5 stacked iso units provision cut and remove the center bar from the...
TRANSCRIPT
INSTALLATION INSTRUCTIONS FOR PART 99-7873
99-7873
APPLICATIONS
Honda CR-V 2007
KIT FEATURES
• DIN Mount Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Mount Radio Provision• Stacked ISO Mount Units Provision
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
TOOLS REQUIRED:Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
D E
C
F
Dash Disassembly- Honda CR-V 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 2- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TABLE OF CONTENTS
99-7873
*Note: Refer also to the instructions included with the aftermarket radio.
99-7873 DASH DISASSEMBLY
HONDA CR-V 2007A
HI
HI
LO
LO
1 23
45
6
SCAN SEEK/SKIPCATEGORY
RPTA-SEL
RDM DISP-MODE
A/C
MAXA/C
B
HI
HI
LO
LO
1 23
45
6
SCAN SEEK/SKIPCATEGORY
RPTA-SEL
RDM DISP-MODE
C
HI
HI
LO
LO
1 23
45
6
SCAN SEEK/SKIPCATEGORY
RPTA-SEL
RDM DISP-MODE
D
HI
HI
LO
LO
1 23
45
6
SCAN SEEK/SKIPCATEGORY
RPTA-SEL
RDM DISP-MODE
1
1
Unclip and remove panel above a/cvents. (Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Unclip a/c control. Unplug and removea/c control. (Figure A)
2
Remove (4) Phillips screws securingthe radio. Unplug and remove radio.(Figure D)
5
Unclip the a/c vent panel includingthe hazard switch. Unplug andremove the panel. (Figure C)
4
Continue to kit assembly.
99-7873 KIT ASSEMBLY
2
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)
1
Slide the aftermarket radio into the DINcage until it snaps into place. (Figure B)
2
Snap the pocket into the radio housing.(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7873 KIT ASSEMBLY
3
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)
1
Slide the radio into the Radio Housinguntil it snaps into place. (Figure B)
2
Snap the Trim Plate onto the front ofthe Radio Housing. (Figure B)
3
Snap the Pocket into the Radio Housing. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7873 KIT ASSEMBLY
4
DOUBLE DIN MOUNT RADIO PROVISION
Cut and remove the center bar fromthe Radio Housing. (Figure A)
1
Snap the Double DIN brackets to theinside edge of the Radio Housing.(Figure B)
2
Slide the Double DIN radio into theDDIN bracket/Radio Housing assemblyand secure the radio to the assemblyusing the screws supplied with theradio. (Figure C)
3
Snap the Double DIN trim plate ontothe front of the Housing/Radio assem-bly. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
99-7873 KIT ASSEMBLY
5
STACKED ISO UNITS PROVISION
Cut and remove the center bar fromthe Radio Housing. (Figure A)
1
Snap the Double DIN brackets to theinside edge of the Radio Housing.(Figure B)
2
Slide the stacked ISO mount units intothe Double DIN Bracket/Radio Housingassembly and secure the units to theassembly using the screws suppliedwith the units. (Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN trim-plate ontothe front of the Housing/Radio assem-bly. (Figure C)
4
99-7873 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
6
NOTES
7
99-7873
NOTES
8
99-7873
NOTES
9
99-7873
99-7873 INSTRUCTIONS
1-800-221-0932 REV. 12/22/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7873
www.metraonline.com