75003a punch pro - hougen read, understand and follow all safety instructions and operating...
TRANSCRIPT
operator’s manualCOVERS HOLE PUNCHER PART NUMBERS 0753101 & 0753201
75003A PUNCH PRO™
ELECTRO-HYDRAULIC HOLE PUNCHER
IMPORTANT SAFETY INSTRUCTIONS
2
WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following.
5. Consider Work Area Environment Do not expose tool to rain Do not use tool in damp or wet locations. Keep work area well lit. Donotusetoolinpresenceofflammable liquids or gases.
6. Guard Against Electric Shock Preventbodycontactwithgrounded sufaces. For example: pipes, radiators, ranges, refrigerator enclosures.
7. Keep Children Away Do not let visitors contact tool or extension cord.Allvisitorsshouldbekeptawayfrom work area.
8. Store Idle Tools Whennotinuse,toolsshouldbestoredina dryhighorlocked-upplace-outofreachof children.
9. Do Not Force Tool Itwilldothejobbetterandsaferattheratefor whichitwasintended. 10. Use Right Tool Donotforcesmalltoolorattachmenttodothe jobofaheavy-dutytool.Donotusetoolfor purpose not intended.
11. Dress Properly Donotwearlooseclothingorjewelry.Theycan becaughtinmovingparts.Rubberglovesand nonskidfootweararerecommendedwhen workingoutdoors.Wearprotectivehaircovering tocontainlonghair.
12. Always wear safety glasses or goggles.
13. Do Not Abuse Cord. Nevercarrytoolbycordoryankitto disconnect from receptacle. Keep cord from heat,oilandsharpedges.
2b. Extension Cords Useonly3-wireextensioncordsthathave 3-pronggroundingtypeplugsand3-pole receptaclesthatacceptthetool’splug. Replace or repair damaged cords. Makesuretheconductorsizeislargeenough to prevent excessive voltage drop causing lossofpowerandpossiblemotordamage
3. FOR ALL DOUBLE-INSULATED TOOLS Whenservicinguseonlyidentical replacement parts.
4. Keep Work Area Clean Clutteredareasandbenchesinviteinjuries.
1. READ ALL INSTRUCTIONS
2. Grounding Instructions 2a. Thistoolshouldbegroundedwhileinuseto protecttheoperatorfromelectricshock.The toolisequippedwitha3-conductorcordand 3-pronggroundingtypeplugtofittheproper groundingtypereceptacle.Thegreen(or greenandyellow)conductorinthecordisthe groundingwire.Neverconnectthegreenor greenandyellowwiretoaliveterminal.If yourunitisforuseon115V,ithasaplugthat lookslikethatshowninsketch(A).Anadapter,seesketches(B)and(C),isavailableforconnectingsketch(A)typeplugsto2-prongreceptacles.Thegreen-coloredrigidear,lug, orthelikeextendingfromtheadaptermustbeconnectedtoapermanentground,suchasa properlygroundedoutletbox. NOTE: Use of a grounding adapter is prohibited in Canada by Part 1 of the Canadian Electrical Code.
TEEFNIDROCFOHTGNEL TEEFNIDROCFOHTGNEL TEEFNIDROCFOHTGNEL TEEFNIDROCFOHTGNEL TEEFNIDROCFOHTGNEL
V511)spmA(
.TF52 .TF05 .TF001 .TF051 .TF002 .TF052 .TF003
6-5 81 61 41 21 01 01 8
8-6 81 61 21 01 01 8 6
01-8 81 41 21 01 8 8 6
21-01 61 41 01 8 8 6 6
41-21 61 21 01 8 6 6 6
61-41 61 21 01 8 6 6 4
PRINCIPLES OF OPERATION
3
CAUTION! To prevent electric shock,donotusepowertoolsnearwetareas,orwherepowertoolmaybecomewet.
Alwaysweareyeprotectionwhileusingpunchingtools,orinthevicinityofpunching.
CAUTION!Theslugisejectedattheendofthepunch.Donotaimtheunitsothatejectedslugmayhitsomeonearound,orbelowyou.
SAFETY FIRSTCAUTION!Riskofpinchingorcrushing.Keepawayfrommovingpartswhenunitisinuse.
Trigger
Punch
Die
Work Stand
Oil PortManual Return
Valve
Handle
Hole Locator Gauge
Stripper
75003A CONTENTS
TheHougen-OguraElectro-hydraulicHolePuncherisanintegratedunit,containingtheelectricmotor,hydraulicpump,and"C"-framepunchingunit.Ituseshydraulicpowertoforcethepunchthroughtheworkpiece,andastrongspringtoreturnthepunchpistontoits"home"position.Thepatenteddesignincludesanautomaticvalvethatreleasesthehydraulicpressurewhenthepunchpistonisatthebottomofitsstroke.Theautomaticvalveremainsopenuntilthepunchpistonhasfullyreturnedtothehomeposition.Asaresultofthisdesign,thepistonwillnotreturntoitshomepositionautomaticallyunlessthefullstrokehasbeencompleted.Also,thepunchwillnotbeginanotherstrokeunlessthepunchhasfullyreturnedtothehomeposition,resettingtheautomaticvalve.Toallowthepunchpistontobemanuallyreturnedintheeventthatthepunchcycleisstoppedpriortocompletion,amanualreturnvalve is provided.
HydraulicOil 753769/16"DiameterPunch 754279/16"DiameterDie-TypeBLong-Formaterial1/8"to1/4" 754679/16"DiameterDie-TypeALong-Formaterial5/64"to1/8" 75466Pin Spanner 7590310mmOpenEndWrench 75771FootSwitch(115V) 75110FootSwitch(230V) 76479FootSwitch(230V,TypeI) 76480Work Stand 75194M3HexKey 75742M4HexKey 75743M5HexKey 75744M6HexKey 75745
Hougen-Ogura Punches are designed tobe used in Structural Steel. If used in harder or higher tensile strength materials, performance will be impeded and serious damaged could occur to your unit.
4
Read,understandandfollowallsafetyinstructionsandoperatingprocedures.Ifyoudonotunderstandtheinstructions or if conditions are not correct for properoperation,donotoperatethemachine.Consultyoursupervisororotherresponsibleperson.
*Checkthatthetriggerswitchisnotlockedon.
*Checkthatthemanualreturnvalveisclosed.
*Makesurethattheproperpunchanddieareinstalledcorrectly.SeeDie Selection and Proper Punches and Dies below.
*Ifyouareusingtheholelocatorgauge,adjustittotheproper distance. See Hole Locator Gauge Adjustment below.
*Plugthepowercordintotheproperpowersupply.
OPERATING PROCEDURES *Positionthepuncherattheproperlocationontheworkpieceusingtheholelocatorgaugeorbylocatingthepointontheendofthepunchintoacenterpunchmarkonthepiece.
Witheverythinginproperorder,theswitchcanbeactivatedtostarttheelectricmotor.Thepunchpistonwillmoveoutandpushthepunchthroughthematerial.Keeptheswitchonuntilthepunchhasreachedtheendofitsstrokeandstops.Releasetheswitch.Theautomaticreturnvalvewillopenattheendofthestrokeallowingthepunchpistontoretracttoitshomeposition.Thepunchpistonmustreturncompletelybeforeanotherholecanbepunched.
Ifthepunchstopsinthemidstofitsstrokeordoesnotcomeoutofthematerial,openthemanualreturnvalve.Oncethepunchpistonhasreturnedtoitshomeposition,tightenthemanualreturnvalve.
Althoughthefootswitchisguardedagainstinadvertentoperation,itisbesttopositionthefootpedalawayfromnormalstandingposition.Placeitinapositionthatre-quiresdeliberateefforttoreachandactivatetheswitch.
Thetriggerswitchshouldbelockedononlywhenreadytopunch.Releasethetriggerswitchimmediatelyafterpunchingtopreventoperationbyinadvertentactuationofthefootswitch.
INSTRUCTIONS -- FOOT SWITCH
TheHolelocatorGaugecanbesettoholdtheHolePunch-esataconstantdistancefromtheedgeoftheworkpiece.Thegaugeisheldinplacebyoneortwosocketheadcapsscrews.Beforemakinganyadjustment,
first,unplugthepowercord.Toadjustthepositionofthegauge,loosenthecapscrew(s),tapthegaugeintothedesiredpositionandretightenthecapscrew(s).
HOLE LOCATOR GAUGE ADJUSTMENT
AllmodelscanbeusedwithanaccessoryworkstandforbenchortablemountingoftheHolePuncher.Thestandisstandardwithallmodels.Toinstallthestand,firstunplugthepowercord.,thenmounttheunittothestandwiththesuppliedhardware.
Whenusingthestand,periodicallychecktomakesurethatthepunchedmaterial(slugs)arenotstackingupbetweentheexitholeinthe"C"-frameandthestand.Keepthisareaclearofaccumulatedslugs.
USING THE WORK STAND
SELECTING PROPER DIESProperdieselectionisessential.Otherthantheobviousnecessityofmatchingshapedpunchesanddies,therearetwootherbasicselectionfactorsthatmustbeconsidered.Thefirstisdieclearance.Differentmaterialtypesanddifferentmaterialthicknessesrequiredifferentclearancesbetweenthepunchanddie.Inordertomaintainthebestpossibleholewhileremainingwithinthetonnagecapacityofthemachine,itisessentialtochoosethediewiththeproperclearance.Thesecondisthedieangle.Moststructuralshapescanbepunchedwiththestandard
flatdies,but"I"-beamsandmostchannelswhichhavea2-in-12taperrequiretheuseofspecial9-1/2degreeangleddies.Carandshipchannelflangesandotherstructuralshapeswitha2degreetapercanbepunchedwithflatdies.Materialswithaflangetaperoflessthan5degreescanalsobepunchedwiththeflatdie,however,theholewillbeslightlyangled.Refertospecificinformationandtableswithinthismanualfortheproperpunchanddiecombination.
5
REMOVING AND INSTALLING PUNCHESPriortoremovingapunch,jogthepunchpistondownuntilitputspressureonapieceofmaterialthatisoftheappropriatethickness.Withapinspanner,loosentheretainingnut.Manuallyreleasethepunchpistonwiththemanualreleasevalve,disconnecttheunitfromthepowersupplyandthenremovetheretainingnutandpunch.Priortoinstallingadifferentpunch,checkfordebrisintheretainingnutandpunchpiston.Cleanifnecessary.Priortoinstallingapunch,verifythe"O"ringonthepunchpistonis clean and not damaged.
Placeyourpunchintotheretainingnut,properlyalignthepunchwithinthepunchpistonandhandtightentheretainingnut.Pluginpower,jogthepunchpistondownuntilitmakescontactwithyourworksurface.Tightentheretainingnutwiththepinspanner.Manuallyreleasethepunchpiston.Yournowreadytopunchyourmaterial.Failuretoalignyourpunchproperlycouldresultinseriousdamagetoyourmachine.Itisnotnecessarytoremoveyourdietoinstallthepunchpiston.
IMPORTANT NOTES:
1. To make it easier, please remove the strippers 3. Pull the die up to the tip of the punch
2. Unscrew the nuts and set screws that hold the die in place
4. Remove the die from the “C”- frame, inclining it to remove.
STRIPPER
STRIPPER
PUNCH
SET SCREW
NUT
REMOVING THE NEW DIE
INSTALLING A PUNCH
1. To make the operation easier, first remove the strippers on both sides.2. Reference your Operators manual and remove your punch and the die.3. Install a new punch and punch retaining nut.4. Install the die (Reference the steps above and work in reverse)5. Tighten the punch retaining nut according to the Instructions in your Operators manual.
New Die Old Die
Hougen-OguraPunchesaredesignedtobeusedinStructural-Steel.Ifusedinharderorhighertensilestrengthmaterials,performancewillbeimpededandseriousdamagecouldoccurtoyourunit.
YourHougen-Ogurapunchunithasbeenequippedwithanewdieconfiguration.Pleasereviewthisinforma-tionpriortooperatingyourmachine.
Inordertoinsuresmootheroperationandlongerlifeofyourholepuncher,thefollowingmaintenanceshouldbedoneperiodically,basedonuse.
1.Keepthemachineclean.Itisespeciallyimportanttokeeptheslidingportionofthepunchpistonfreefrommetalchips,scale,dirt,dustorotherdebris.Tocleanthepunchpiston,turnontheswitchtomovethepunchpistonalmosttothebottomofitsstroke.Ifnecessary,cyclethepunchseveraltimestodeterminewherethebottomofthestrokeis,andtocorrectlypositionthepunchpiston.
Unplugthepowercord.Wipeanydebrisfromtheexposedpartofthepunchpiston.
2.Regularlytightenallfastenersandreplaceanyworn components.
3.Checkpowercord,ifcrackedorfrayed,returnthemachinetoanauthorizedrepaircenterforreplacement.
4.Checkoillevelcarefully,usingtheprocedurebelow.
ADDING OILUseofthecorrecthydraulicoilisessential.ApprovedoilsareShell"TELLUSOil"andExxon"TERESSTIC"(PartNo.75376).Grade#46viscositymustbeused.Checktheunitspecifications.Makesurethattheworkareaandallequipmentarecleansothatnodirt,dustorotherforeignmaterialcangetintothehydraulicoilorpumparea.
1.Locatethesocketheadcapscrewthatplugstheoilport.ItisjustabovethemanualreturnleverontherighthandsideoftheHolePuncher.
2.LaytheHolePuncheronitsleftsidesothattheoilportis facing up.
3.Turnontheswitchtomovethepunchpistonalmosttothebottomofitsstroke.Ifnecessary,cyclethepunchseveraltimestodeterminewherethebottomofthestrokeis,andtocorrectlypositionthepunchpiston.Inthisposition,themaximumamountofoilhasbeendrawnfromthepumpandthecorrectfillcanbeobtained.
4.Carefullyopentheoilportbyremovingthesocketheadcapscrew.
5.UsingthesmallsqueezebottlesuppliedwiththeHolePuncher,carefullyaddhydraulicoiltocompletelyfillthereservoir.RocktheHolePuncherbackandforthslightlyseveraltimestofreeanytrappedairbubbles,thenaddadditionaloilifnecessary.
6.Replacethecapscrewandwipeupanyexcessoil.
7.CycletheHolePuncherseveraltimeswiththeManualReturnValveopen,andagainwiththevalveclosed,toworkanytrappedairoutofthesystem,thenrepeattheaboveprocedure,makingsurethatthepunchpistonisalmostatthebottomofthestrokebeforeremovingthecapscrewfromtheoilport.
8.Addadditionaloilasnecessary.Iftheunitwasextremelylowonoil,itmaybenecessarytorepeattheprocedureseveraltimes.
6
MAINTENANCE
NOTE: The internal components of the pump and piston area have very close clearances and are sensitive to damage from dust, dirt, contamination of the hydraulic fluid or improper handling. The disassembly of the pump housing requires special tools and training, and should be attempted by a qualified repair person. The improper servicing of electrical components can lead to conditions that could cause serious injury.
ANY ATTEMPT BY UNAUTHORIZED PERSONNEL TO SERVICE THE INTERNAL COMPONENTS OF THE PUMP AREA WILL VOID THE WARRANTY.
HELPFUL HINTS FOR HOLE PUNCHINGEachofthepunchesisprovidedwithasharppointatitscenter.Iftheholelocationsarecenterpunched,thepointontheendofthepunchmaybeusedto"find"thecenterpunchedspot.
Also,foraccurateandeasypositioningofthepunchtoaholelocation,theswitchcanbeintermittentlypulsedonandofftojogthepunchdowntotheworksurface.
Ifthepositionisnotsatisfactory,openthemanualreturnvalvetoretractthepunchforanotherattempt.Thisoperationcanalsobeperformedwiththemanualreturnvalve"cracked"openslightlytopreventfullpunchingpressurefrombeingdeveloped.Inthismanner,thepunchcanbeeasilybroughtrightdowntothesurfacewithoutbeginningtopunchthehole.Ifthelocationissatisfactory,closethevalveandfinishtheoperation.
2
100
798081
83
7475
86
85
7882 84
87 8889
90
91
87
9678
75
74
9394
95
96
98
9792
85
99
69
6867
66
6564
70
71 72
73
1
223
3
4
56
78
8
9
9
10
2
11
12
1314
1516
17
18
1920
2122
2324
2526
27 282930
31
323334
37
3536
3938
40
48 4950
51
5152
47
464544434241
5455
565657
58
59 6061
6362
5347
1413
101
41
41
42
42
43
43
44
44
45
45
46
46
47
76
77
7
75003A EXPLODED VIEW
PARTS LIST - 75003A
8
Item Part # Description Qty
53 75321 Cylinderw/Chamfer 154 75186 Gasket 155 75086 Ball Bearing 256 75055 Spacer 257 75088 Roller Bearing 158 75089 Retaining Ring 159 75127 Pump Housing 160 75084 Oil Seal 161 75087 Ball Bearing 162 75090 WasherSeal 163 75107 Screw 10mm X 15mm 164 75820 SubPlate 165 75821 Armature(115V) 1
76469 Armature(230V) 166 75822 PaperWasher 167 75823 Ball Bearing 168 75824 ThrustWasher16mm 169 75825 RubberPin 270 75827 FanGuide 171 75828 Screw 5mm X 65mm 272 75829 Field(115V) 1
76470 Field(230V) 173 75830 Field Support Set 174 75831 BrushCap 275 75832 CarbonBrush(pair) 176 75864 Caution Tag 177 75833 Rivet 478 75834 Anti-VibrationPad 279 75835 FlatWasher 480 75836 SpringWasher 481 75837 Bolt 5mm X 25mm 482 75865 Warning Tag 183 75868 Name Tag 184 75838 Motor Housing Set 185 75839 Handle Set 186 75840 Label 187 75841 Pin 288 75842 Compression Ring 189 75843 Button 190 75844 Switch 191 75845 Spacer 192 75846 SwitchLever 193 75847 RubberPlate 194 75848 CordClamp(115V) 1
76446 CordClamp(230V) 195 75849 Screw4mmX18mm 296 75850 Anti-VibrationPad 497 75851 Screw4mmX25mm 598 75852 StrainRelief(115V) 1
76449 StrainRelief(230V) 199 75870 PowerCord(115V) 1
76451 PowerCord(230V) 176477 PowerCord(230V,TypeI) 1
100 75194 Work Stand 1101 75110 FootSwitch(115V) 1
76479 FootSwitch(230V) 176480 FootSwitch(230V,TypeI) 1
Item Part # Description Qty
1 75180 C-Frame 12 75156 Screw M6 X 15MM 23 75157 FlatWasher6MM 24 75182 Hole Locator 15 75165 PunchRetainingNut 16 75164 “O” Ring 17 75427 Punch9/16Die 18 75131 Stripper 2 75131L Stipper(Long) 29 75162 HeliWasher6MM 210 75156 Screw8MMX15MM 611 75192 Screw 6MM X 10MM 112 75191 Steel Ball 113 75091 Hex Nut M6 214 75189 Screw M6 X 15MM 215 75158 ScrewM8X20MM 1816 75159 FlatWasher 1817 75466 Die-Long9/16TypeA 1
75467 Die-Long9/16TypeB 118 75185 O-Ring 119 75137 Oil Bladder 120 75136 Bladder Screw 121 75190 O-Ring 122 75188 BladderBushingScrew 123 75155 Helicoil 124 75138 Bladder Retain. Scew 125 75152 Back Up Ring 126 75153 Rod Seal Packing 127 75187 PunchReturnSpring 128 75099 Roll Pin 2.5mm X 10mm 129 75135 PunchPistonKey 130 75128 PunchPiston 131 75154 Packing 132 75042 Release Valve 133 75043A Valve Return Spring 134 75183 Stop Plate 135 75101 FlatWasher4mm 236 75102 Screw4mmX6mm 237 75184 Valve Release Spring 138 75863 Bolt 5mm X 70mm 439 75862 Washer5mm 440 75063 PunchHandle 141 75325 RubberPackingw/groove 342 75326 PackingO-Ring 343 75052 CheckValveSpring 344 75050 CheckValve 345 75053 Pump Piston Return Spring 3
46 75048 A-J PumpPistonsarereplacedbysizeandfit.PumPCylindershouldbesent to Hougen Mfg.
47 75054 Magnet 348 75100 Roll Pin 149 75085 O-Ring 150 75046 Return Valve 151 75160 Screw6mmX8mm 252 75047 Return Lever 1
9
ROUND PUNCHES AND DIES FOR 75003APunch-Pro™ — Model 75003AROUND PUNCH MATERIAL DIE
Size PartNo. Thickness Style Size Part
No.Nominal Actual Metric
1/4" .256 6.5mm 75421
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/4 A 75454
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/4 B 75455
5/16" .315 8mm 75422
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 5/16 A 75456
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 5/16 B 75457
11/32" .335 8.5mm 75423
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/32 A 75458
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/32 B 75459
3/8" .394 10mm
75424
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 3/8 A 75460
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 3/8 B 75461
75476(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 3/8 A 75438
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 3/8 B 75439
19/64 (.297)max. C Die 3/8 C 75450
7/16" .433 11mm
75425
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 7/16 A 75462
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 7/16 B 75463
75477(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 7/16 A 75440
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 7/16 B 75441
19/64 (.297)max. C Die 7/16 C 75451
15/32" .472 12mm
75917
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 15/32 A 75920
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 15/32 B 75921
75918(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 15/32 A 75922
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 15/32 B 75923
19/64 (.297)max. C Die 15/32 C 75924
1/2" .512 13mm
75426
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/2 A 75464
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/2 B 75465
75478(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 1/2 A 75442
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 1/2 B 75443
19/64 (.297)max. C Die 1/2 C 75452
9/16" .551 14mm
75427
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 9/16 A 75466
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 9/16 B 75467
75479(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 9/16 A 75444
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 9/16 B 75445
19/64 (.297)max. C Die 9/16 C 75453
5/8" .625 15.9mm 75428
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 5/8 A 75468
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 5/8 B 75469
11/16" .688 17.5mm 75429
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/16 A 75470
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/16 B 75471
23/32" .709 18mm 75919
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 23/32 A 75925
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 23/32 B 75926
3/4" .748 19mm 75430
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 3/4 A 75472
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 3/4 B 75473
25/32" .787 20mm 75431
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 25/32 A 75474
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 25/32 B 75475
OBLONG PUNCH MATERIAL DIESize Part
No. Thickness Style Size PartNo.Nominal Actual Metric
1/4"x
1/2"
.256x
.512
6.5mmx
13mm
75638
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/4 x 1/2 A 75656
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/4 x 1/2 B 75657
75666(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 1/4 x 1/2 A 75643
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 1/4 x 1/2 B 75644
19/64 (.297)max. C Die 1/4 x 1/2 C 75653
11/32"x
1/2"
.335x
.512
8.5mmx
13mm
75639
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/32 x 1/2 A 75658
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/32 x 1/2 B 75659
75667(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 11/32 x 1/2 A 75645
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 11/32 x 1/2 B 75646
19/64 (.297)max. C Die 11/32 x 1/2 C 75654
7/16"x
5/8"
.433x
.650
11mmx
16.5mm
75640
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 7/16 x 5/8 A 75660
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 7/16 x 5/8 B 75661
75668(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 7/16 x 5/8 A 75647
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 7/16 x 5/8 B 75648
19/64 (.297)max. C Die 7/16 x 5/8 C 75655
1/2"x
3/4"
.512x
.768
13mmx
19.5mm75641
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/2 x 3/4 A 75662
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/2 x 3/4 B 75663
9/16"x
13/16"
.551x
.827
14mmx
21mm75642
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 9/16 x 13/16 A 75664
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 9/16 x 13/16 B 75665
10
OBLONG PUNCHES AND DIES FOR 75003A Punch-Pro™ — Model 75003AROUND PUNCH MATERIAL DIE
Size PartNo. Thickness Style Size Part
No.Nominal Actual Metric
1/4" .256 6.5mm 75421
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/4 A 75454
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/4 B 75455
5/16" .315 8mm 75422
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 5/16 A 75456
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 5/16 B 75457
11/32" .335 8.5mm 75423
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/32 A 75458
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/32 B 75459
3/8" .394 10mm
75424
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 3/8 A 75460
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 3/8 B 75461
75476(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 3/8 A 75438
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 3/8 B 75439
19/64 (.297)max. C Die 3/8 C 75450
7/16" .433 11mm
75425
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 7/16 A 75462
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 7/16 B 75463
75477(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 7/16 A 75440
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 7/16 B 75441
19/64 (.297)max. C Die 7/16 C 75451
15/32" .472 12mm
75917
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 15/32 A 75920
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 15/32 B 75921
75918(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 15/32 A 75922
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 15/32 B 75923
19/64 (.297)max. C Die 15/32 C 75924
1/2" .512 13mm
75426
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/2 A 75464
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/2 B 75465
75478(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 1/2 A 75442
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 1/2 B 75443
19/64 (.297)max. C Die 1/2 C 75452
9/16" .551 14mm
75427
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 9/16 A 75466
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 9/16 B 75467
75479(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 9/16 A 75444
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 9/16 B 75445
19/64 (.297)max. C Die 9/16 C 75453
5/8" .625 15.9mm 75428
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 5/8 A 75468
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 5/8 B 75469
11/16" .688 17.5mm 75429
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/16 A 75470
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/16 B 75471
23/32" .709 18mm 75919
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 23/32 A 75925
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 23/32 B 75926
3/4" .748 19mm 75430
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 3/4 A 75472
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 3/4 B 75473
25/32" .787 20mm 75431
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 25/32 A 75474
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 25/32 B 75475
OBLONG PUNCH MATERIAL DIESize Part
No. Thickness Style Size PartNo.Nominal Actual Metric
1/4"x
1/2"
.256x
.512
6.5mmx
13mm
75638
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/4 x 1/2 A 75656
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/4 x 1/2 B 75657
75666(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 1/4 x 1/2 A 75643
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 1/4 x 1/2 B 75644
19/64 (.297)max. C Die 1/4 x 1/2 C 75653
11/32"x
1/2"
.335x
.512
8.5mmx
13mm
75639
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 11/32 x 1/2 A 75658
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 11/32 x 1/2 B 75659
75667(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 11/32 x 1/2 A 75645
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 11/32 x 1/2 B 75646
19/64 (.297)max. C Die 11/32 x 1/2 C 75654
7/16"x
5/8"
.433x
.650
11mmx
16.5mm
75640
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 7/16 x 5/8 A 75660
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 7/16 x 5/8 B 75661
75668(LP)
5/64 (.078) to 1/8 (.125)14 to 11 GA.
F, A,H, L
Die 7/16 x 5/8 A 75647
>1/8 (.125) to 1/4 (.250)10 to 3 GA.
F, A,H, L
Die 7/16 x 5/8 B 75648
19/64 (.297)max. C Die 7/16 x 5/8 C 75655
1/2"x
3/4"
.512x
.768
13mmx
19.5mm75641
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 1/2 x 3/4 A 75662
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 1/2 x 3/4 B 75663
9/16"x
13/16"
.551x
.827
14mmx
21mm75642
5/64 (.078) to 1/8 (.125)14 to 11 GA. F, A, H Die LD 9/16 x 13/16 A 75664
>1/8 (.125) to 1/4 (.250)10 to 3 GA. F, A, H Die LD 9/16 x 13/16 B 75665
MELBORP ESUAC NOITULOS
TUBSNURROTOMSEODNOTSIPHCNUP
TUOEMOCTON
NEPOSIEVLAVNRUTERLAUNAM EVLAVNRUTERLAUNAMESOLC
TNEICIFFUSNISILIO LIODDA
DENRUTERTONSAHNOTSIPEMOHSTIOTYLETELPMOC
,SPIHCLEETSOTEUDNOITISOPEHTNOSIRBEDREHTOROTRID
REDLOH-HCNUPDESOPXE.NOITISOP
DESOPXEMORFSIRBEDNAELCFONOITROPREDLOH-HCNUP
NOTSIPHCNUPHSUP.DORNOTSIP.NOITISOPEMOHSTIOTKCAB
SIGNIRPSNRUTERNOTSIPHCNUPDORHCNUPNRUTEROTKAEWOOT
EHTYBDECIVRESENIHCAMEVAHYROTCAF
SEMOCNOTSIPHCNUPGNIHCNUPTUB,TUOKAEWOOTSIREWOP
HCNUPOT
TONSIEVLAVNRUTERLAUNAMDESOLCYLETELPMOC
EVLAVNRUTERLAUNAMESOLC
SIRIAROTNEICIFFUSNISILIORIOVRESERNIDEPPART
LIODDA
STRAPNOTSIPROPMUPLANRETNIDEGAMADROYTRID,NROWERAYLREPORPGNINOITCNUFTONDNA
EHTYBDECIVRESENIHCAMEVAHYROTCAF
TONSEODROTOMROOPROETATOR
ROTOMFONOITATOR
TIUCRICREWOPNEPO,DROCNOISNETXE,GULPKCEHC
REKAERBTIUCRIC
EGATLOVREPORPMI ECRUOSREWOPKCEHC
PORDEGATLOVEVISSECXEFOERASDROCNOISNETXE
EHTROFEZISERIWTNEICIFFUSNI.DROCEHTFOHTGNEL
ROSDROCDEGAMADRONROW.SEHSURBNOBRACNROW.SGULPSTRAPROTOMLANRETNIDEGAMAD
EHTYBDECIVRESENIHCAMEVAHYROTCAF
NEEWTEBGNIKAELLIODNAEMARF"C"
NEEWTEBROREDNILYCPMUPDNAREDNILYC
GNISUOH
THGITTONERASTLOB STLOBNETHGIT
DEGAMADSITEKSAGEHTYBDECIVRESENIHCAMEVAH
YROTCAF
DNUORAGNIKAELLIOMORFRONOTSIPAERALANRETNI
SECAFRUSROSLAESLANRETNIKCASRELEVELLIO.DEGAMADERA
NEKORBSI
EHTYBDECIVRESENIHCAMEVAHYROTCAF
TONSEODHCNUPFOTUOPIRTS
RETFAECEIPKROWGNIHCNUP
NROWSIEIDROHCNUP ECALPER
ROLAIRETAMROFEIDREPORPMISSENKCIHT
DNAHCNUPREPORPROFKCEHCNOITCELESEID
HTOBREDNUTONSAWECEIPKROWROGNIDNIBSIDNASREPPIRTS
HCNUP
SILAIRETAMEHTTAHTERUSEKAMGNIHCNUPEHTNIDETAESYLLUF
AERA
TROUBLESHOOTING
11
HougenManufacturing,IncorporatedwarrantsitsPortableMagneticDrills,Electro-hydraulicHolePunchersforaperiodof(1)oneyearandotherproductsforninety(90)daysfromdateofpurchaseagainstdefectsduetofaultymaterialorworkmanshipandwillrepairorreplace(atitsoption)withoutchargeanyitemsreturned.Thiswarrantyisvoidiftheitemhasbeendamagedbyaccidentorunreasonableuse,neglect,improperservice,orothercausesnotarisingoutofdefectsinmaterialorworkmanship.Nootherexpressedwarrantyisgivenorauthorized.HougenManufacturing,Inc.disclaimsanyimpliedwarrantyofMERCHANTABILITYorFITNESSforanyperiodbeyondtheexpressedwarrantyandshallnotbeliableforincidentalorconsequentialdamages.Somestatesdonotallowexclusionsofincidentalorconsequentialdamagesorlimitationonhowlonganimpliedwarrantylastsand,ifthelawofsuchastategovernsyourpurchase,theaboveexclusionandlimitationmaynotapplytoyou.Thiswarrantygivesyouspecificlegalrightsandyoumayalsohaveotherrightswhichvaryfromstatetostate.
Toobtainwarrantyservice,returntheitem(s),transportationprepaid,toyournearestFactoryAuthorizedRepairCenterortoHougenManufacturing,Inc.,3001HougenDrive,SwartzCreek,Michigan48473. HougenDrills(RotabroachCutters)arewarrantedagainstmanufacturingdefectsonly.SubjecttoHougenManufacturing inspection.
THISWARRANTYISINLIEUOFANYOTHERWARRANTY,EXPRESSEDORIMPLIED,INCLUDINGANYWARRANTYOFMERCHANTABILITYORFITNESSFORAPARTICULARPURPOSE© 2012 Hougen Manufacturing, Inc.
Commercial / Industrial Limited Warranty
PhotographsandSpecificationsshownareaccurateindetailattimeofprinting.Manufacturereservestherighttomakeimprovementsandmodificationswithoutpriornotice.Hougen,Hougen-Edge,Rotabroach,Punch-Pro,Trak-StarandtheHougenlogoareproprietarytrademarksofHougenManufacturing,Inc.OguraandOguralogoareproprietarytrademarksofOgura&Co.,Ltd.
Hougen-Ogura Patent Notice
Factory Warranty Repair Servicescanbeobtainedbysendingyourproductto:
Hougen Manufacturing, Inc.3001 Hougen Drive
SwartzCreek,MI48473Attn: Repair Department
Hougen Manufacturing, Inc.P.O.Box2005Flint,MI48501-20053001HougenDrive•SwartzCreek,MI48473Phone(810)635-7111Fax(810)635-8277www.hougen.com•[email protected]
OM75003A0913 Printed in U.S.A.© 2013 Hougen Manufacturing, Inc.