0

Notice for assembly:

1. Do not fold or squeeze the wires, cables or hoses.2. Ensure to connect the couplers or connectors in correct position tightly.3. Do not force to pull or squeeze any wire, cable or hose, that way would damage parts. To orginize wires, calbes and hoses in correct position before assembling.4. O2 sensor is a very expensive but fragile part, be more careful while assembling. a. Be sure to disconnect the coupler before dismantling the exhaust pipe while maintaining, prevent from damage the wire and O2 sensor. b. Do not heat the O2 sensor or coupler when maintaning it would cause malfuction.5. When dismantle the ECU couple, do not pull or squeeze the fixed rod or wire, it would cause malfuction.

D

R2 R1R5

R4

TOP VIEW

R3

F1

L1 L2 L3 L4 L5 L5F2

5. Cable, Wire and Hose Routing. MYROAD 700i

FRONT VIEW

F1FRNOT VIEW-1

ABS controller's coupler need

to be in correct position. Fixed band

Fix ABS wire by soft hook.

Fixed hook

Notice for assembly:

1. Ensure the wires, cables or hoses in correct routes.2. Replace the wires, cables or hoses in correct routes ifany damage found.

F2FRONT VIEW-2

Fixed hook

ABS controller

Tire pressure monitor

system controller

Fixed band

Fixed hookDirection of screw.

Oil gas recycle (oil tank end)

3 way pipe

3 way pipeOil gas recycle (air cleaner end)

L1LEFT VIEW-1

ABS ECU wire

Vacuum pipeMETER wirefixed hook

Fix water pipe and oil

gas pipe by soft hook.

Fix the cable and oil gas pip by soft hook.

Radiator pipe

CANISTER 3 way

Fix cam sensor by band.

L2LEFT VIEW-2

1. Install the radiator pipe first.

2. Then install theoil gas pipe. 3. Fix the wire.

4. Fixed by softh k

Notice for assembly:1. Radiator pipe and air pipe can not be twisted or squeezed.

L3LEFT VIEW-3

The route of vacuum pipe

01

Locate all the cables and

wires under stay.

Locate all the wires and

cables in hook and fix them,

except throttle cable and

seat-lock cable.

Vacuum pipe

L4LEFT VIEW-4

The cable of rear food step need to be located upon

the secondary water tank.

The harness wire should be

located behind the frame.

These bands fix harness wire only.Accelerated cable.

Decelerated cable.

Fix by band.

Fix by band.

Fix by band.

Confirmation:1. Ensure those C-type

hooks to be fixed firmly.

2. Do not assemble both

oil coolant pipe in the

wrong position.

LEFT VIEW-5-Notice for route of radiator pipe.

Oil coolant cycle loopwhich conducts to oil filter loop. Small cycle loop. Coolant outs from engine. The pipe of radiator cap.

Coolant gets into engine

bye this pipe.

Both oil coolant pipes should not be

assembled bye the wrong position.

L5

L6LEFT VIEW-6

Seat lock route

The coupler of suspension motor.

The terminals should be

installed upon the battery

contacts.

The cable should not be tightened,

it should be installed with tolerance.

Spong patchs.

Fix by band.

R1RIGHT VIEW-1

Throttle body should be installed in precise position.

Controllers' coupler located under the stay.

Locate the wirebetween bothcouplers.

Wheel speed sensor

Rear brake hose.

Parking brake

Crank Position SensorCOUPLER

R2RIGHT VIEW-2

O2 sensor's coupler need tobe located on the cover.

The route of rear

brake cable.

ECU coupler need to be fixed in

correct position firmly.

Fix the cable by soft hook.

Fix by band.

Condenser's position.

RIGHT VIEW-3

Fan cable and harness wire coupler

Locate the parkingbrake cable underthe stay.

Heat insulating by pastethe aluminum foil on theframe pipe.

Fixed by soft hooks.

Fixed by band.

The fixed order asfollowing,1.Brake oil pipe2.COIL wire

3.Air cleaner pipe

4.The pipe of small

circle

Fixed by band.

Paste with aluminum foil.

RIGHT VIEW-4

Oil gas recycle(CAP end)

Fix the pipe by 8-type ring.

Fix the hazard controller wire by soft hook.

Pressure sensor wire's route.

RIGHT VIEW-5

Wheel speed sensor's 8-type hook need to befixed in correct position.

Parking brake

Fix position the brake oil pipe.

Parking brake switch terminal.

RIGHT VIEW-6

Fix the wheel speedsensor by band.

Fix the harness wire by hook.

D1TOP VIEW-1

The screws mount inside.

Fix the fuel pump pipes as picture'sshowing

Notice for assembly:

1. Injectors' wires have been marked in R(right) and L(left) for your reference, do notassemble in wrong position.2 D t th ' l

The routes of pipes: Oil gas recycle pipe Oil tank cap pipe

The routes of injectors' pipes.

The route of ISC pipe.

TOP VIEW-2Notic for oil pipes' routes

Mounting the oil pipes' screws follow the picture.

2 Throttle cables

Right oil pipe

Right handle bar

wire

Eletrical

suspension

Rear foot step's cable.

Wires and pipes locate understay.

TOP VIEW-3

Do not fix seat lock cables by hook.

Left oil pipe

Right handle

barwire

Do not fix seat lock cables by hook.

Fix by hook.

TOP VIEW-4

Handle bar switch wire Brake cable Throttle cable Handle bar switch wire

Brake cable