319 ho dual battery (acb - icc) 11-29-02
DESCRIPTION
mercedesTRANSCRIPT
![Page 1: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/1.jpg)
1
W211 Dual Battery SystemW211 Dual Battery System
319 HO BCM (ACB-ICC) 11-29-02
![Page 2: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/2.jpg)
2
These technical training materials are current as of the date noted on the materials, and may be revised or updated without notice. Alwayscheck for revised or updated information.
To help avoid personal injury to you or others, and to avoid damage to the vehicle on which you are working, you must always refer to thelatest Mercedes-Benz Technical Publication and follow all pertinent instructions when testing, diagnosing or making repair.Illustrations and descriptions in this training reference are based on preliminary information and may not correspond to the final US versionvehicles. Refer to the official introduction manual and WIS when available.Copyright Mercedes-Benz USA, LLC, 2002
Reproduction by any means or by any information storage and retrieval system or translation in whole or part is not permitted without writtenauthorization from Mercedes-Benz USA, LLC or its successors.Published by Mercedes-Benz USA, LLCPrinted in U. S.A.
![Page 3: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/3.jpg)
3
Program HighlightsProgram Highlights• Power distribution
- pre-fuse diagram- pre-fuse locations
• Dual battery on-board electrical system components- systems battery- auxiliary battery- battery control module- auxiliary battery relay- cut-off relay for interruptible loads- polyswitch fuse
• Dual battery functional description
- normal modes- failure modes
![Page 4: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/4.jpg)
4
W211 Dual Battery System FunctionW211 Dual Battery System Function
An auxiliary battery supplies electrical energy for alimited time if the systems battery voltage is low.
![Page 5: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/5.jpg)
5
Systems Battery (G1)Systems Battery (G1)
Location: (G1) installed in trunk
![Page 6: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/6.jpg)
6
W211 Systems Battery (G1)W211 Systems Battery (G1)
• Systems Battery: 12V, 95 Ah, 520A (DIN)
• Absorbent Glass Mat (AGM) design, also known as Valve Regulated Lead Acid(VRLA) type
• Function - Primary power source for all vehicle electrical systems
![Page 7: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/7.jpg)
7
Location of Auxiliary Battery (G1/7)Location of Auxiliary Battery (G1/7)
Auxiliary battery installed below air intake of HVAC
![Page 8: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/8.jpg)
8
Location of Auxiliary Battery (G1/7)Location of Auxiliary Battery (G1/7)
Shown with HVAC air intake / fiter removed
![Page 9: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/9.jpg)
9
• Auxiliary Battery: 12V, 12Ah, 170 A (DIN)
• Absorbent Glass Mat (AGM) design
• Function - Provides supplemental power if systems battery (G1) voltage is low
Auxiliary Battery (G1/7)Auxiliary Battery (G1/7)
![Page 10: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/10.jpg)
10
AGM / VRLA Battery ConstructionAGM / VRLA Battery Construction
• Completely sealed case construction
• No liquid electrolyte
• Absorbent glass mat (V) holds electrolyte in contact with positive and negative plates
• Vent valve is normally sealed no gases can escape during normal charging
• Vent valve is only opened if internal pressure exceeds predetermined level
The major differences in construction between
a AGM battery and standard lead acid
automotive battery are:
![Page 11: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/11.jpg)
11
AGM / VRLA Battery PropertiesAGM / VRLA Battery Properties
• Longer service life
• Improved cold starting characteristics
• Improved deep cycle performance
• No liquid acid spills or leaks
• Fast recharge time
• Completely maintenance free
![Page 12: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/12.jpg)
12
AGM / VRLA Battery Testing•• AGM batteries cannot be tested using previous methods (load and acid densityAGM batteries cannot be tested using previous methods (load and acid density
tests)tests)
•• Requires the new Midtronics MCR 717 tester and printerRequires the new Midtronics MCR 717 tester and printer
•• Tester measures battery conductance by inducing A/C voltage of a given frequencyTester measures battery conductance by inducing A/C voltage of a given frequencyand amplitude on the battery posts and monitoring the current flow in response to itand amplitude on the battery posts and monitoring the current flow in response to it
•• Discard the acid density sheet, and enter test code (recorded by tester) on warrantyDiscard the acid density sheet, and enter test code (recorded by tester) on warrantyclaim formsclaim forms
•• Battery replaced under warranty must have a test printout attached to the R.O.Battery replaced under warranty must have a test printout attached to the R.O.
•• Detailed information about testing, and using the MCR717 can be found in WISDetailed information about testing, and using the MCR717 can be found in WISSI54.10-P-0003-01SI54.10-P-0003-01
![Page 13: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/13.jpg)
13
F32
Pre-fuse Box (F32)Pre-fuse Box (F32)
Location: Passenger footwell
![Page 14: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/14.jpg)
14
Front Front Pre-fusePre-fuse BoxBox (F32)(F32)
7071
72 73 74 75 76 77
![Page 15: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/15.jpg)
15
Front Front Pre-fusePre-fuse BoxBox (F32)(F32) DisassembledDisassembled
Capacitor 4700µF
![Page 16: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/16.jpg)
16
Front Pre-fuseFront Pre-fuse Box (F32) DisassembledBox (F32) Disassembled((terminal unit fuses)terminal unit fuses)
Viewed from top
![Page 17: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/17.jpg)
17
Pre-fuse BoxPre-fuse Box (F33)(F33)
F33
Location: Front of spare tire well
![Page 18: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/18.jpg)
18
Pre-fusePre-fuse BoxBox (F33)(F33)
f78f79
f80
f81
![Page 19: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/19.jpg)
19
Rear Rear Pre-fusePre-fuse BoxBox (F33) Disassembled(F33) Disassembled
f78
f80
f81
f81
![Page 20: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/20.jpg)
20
f77Res.40 Af76 N2240 Af75N10/1140 Af74K6740 Af73A7/350 Af72A7/3
150 Af71M4/7150 Af70
F32
200 Af78N10/1200 Af79N10/2150 Af80N10/1150 Af81F34
5 Af84N825 Af85 N112 and A35/115 Af86X58/140 Af87M40/1
f89Res.
F33
G2
G1/7 -+
N82K57/2
- +G1
M1
Pre-fusePre-fuse Power DistributionPower Distribution
![Page 21: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/21.jpg)
21
Legend: Pre-fuseLegend: Pre-fuse Power DistributionPower DistributionA7/3 Traction system hydraulic unit
N112 Communication platform (CP)
A35/11 Voice recognition module (VCS)F32 Front pre-fuse boxF33 Rear pre-fuse boxF34 Interior fuse box (left of instrument panel)G1 Systems battery G1/7 Auxiliary batteryG2 AlternatorK57/2 Auxiliary battery relayK67 AIRmatic relayN10/1 Driver signal acquisition and actuation module (SAM-D)N10/2 Rear signal acquisition and actuation module (SAM-R)N10/11 Passenger signal acquisition and actuation module (SAM-P)N22 Air conditioning control moduleN82 Battery control module
M1 Starter motorM4/7 Electric suction fan with integrated controlM40/1 Pneumatic pump of dynamic seat controlX58/1 Interior socket
![Page 22: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/22.jpg)
22
Battery Control ModuleBattery Control Module (N82)(N82)
Location: Rear of spare tire well
![Page 23: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/23.jpg)
23
Function of N82Function of N82 1. Monitors the voltages of (G1) and (G1/7)
2. Monitors alternator voltage (terminal 61) via CAN B
3. Controls auxiliary battery relay (K57/2)
4. Controls consumer prioritization function
5. Optimizes charging of auxiliary battery (G1/7)
6. Notes emergency operation and sets fault codes
(CAN communication / DTC’s)
7. Notes emergency operation resulting in IC / MF fault message
displays
![Page 24: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/24.jpg)
24
Polyswitch Fuse (F30)Polyswitch Fuse (F30)
Location: Behind auxiliary battery (G1/7)
Polyswitch fuse (F30)
![Page 25: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/25.jpg)
25
Polyswitch Fuse (F30)Polyswitch Fuse (F30)
• Positive temperature coefficient thermistor
• 5A rating
• Protects internal voltage sensing circuit in N82
![Page 26: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/26.jpg)
26
Auxiliary Battery Relay (K57/2)Auxiliary Battery Relay (K57/2)
Location: Below windshield wiper cowl plastic trim
Function:• Controlled by N82• De-energized during normal operation (N.O.)• Energized to recharge G1/7• Energized if engine running and system voltage low• Connects G1/7 to electrical consumers
![Page 27: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/27.jpg)
27
Cut-off Relay for Interruptible Loads (K75)Cut-off Relay for Interruptible Loads (K75)
Function:• Controlled by N82
• De-energized during normal operation (N.C.)
• Energized during emergency operation
• Opens 30/15R to cigar lighter (R3r1), and 12V socket (X58/1) rear of centerconsole during emergency operation
K75
Location: LF SAM (N10/1)
K75
or
![Page 28: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/28.jpg)
28
Dual Battery System DiagramDual Battery System DiagramF33
G1
G1/7
M1G2K57/2
30 87
F30E
EN82
Kl. 30
Kl. 31
F32
CAN-B
-
+
+-
F30 Polyswitch fuse F32 Front pre-fuse boxF33 Rear pre-fuse box
G1 BatteryG1/7 Auxiliary batteryG2 Alternator
K57/2 Auxiliary battery relayM1 StarterN82 Battery control module
![Page 29: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/29.jpg)
29
Normal ModeNormal Mode
- Battery control module monitors voltages and calculates the condition of both batteries
- Monitors total current consumption through common ground
- Consumer prioritization off
- Relay K57/2 de-energized
F33
G1
G1/7
M1G2K57/2
30 87
F30E
EN82
Kl. 30
Kl. 31
F32
CAN-B
-
-
+
+
F30 Polyswitch fuse F32 Front pre-fuse boxF33 Rear pre-fuse box
G1 BatteryG1/7 Auxiliary batteryG2 Alternator
K57/2 Auxiliary battery relayM1 StarterN82 Battery control module
![Page 30: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/30.jpg)
30
Multi-Function DisplayMulti-Function Display Fault MessagesFault Messages
![Page 31: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/31.jpg)
31
Consumer PrioritizationConsumer Prioritization
If, for example, the alternator fails:
• Both consumer prioritization stages (1 and 2) are immediately activated via the CAN
• A red warning info appears in the instrument cluster• The auxiliary battery is not engaged until G1 voltage is low
If for example, N82 determines that the load capacity of systems battery (G1)is inadequate:
• Stage 1 consumer prioritization via CAN• Stage 2 consumer prioritization via CAN
(if deactivating stage 1 consumers was not adequate)• The auxiliary battery is connected and the red warning then appears in the instrument cluster
![Page 32: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/32.jpg)
32
Engine running, systems battery low:
- Consumers deactivated in 2 stages by CAN messages
- Fault messages in instrument cluster indicate deactivation of consumers
- Auxiliary battery relay (K57/2) is energized. Auxiliary battery is connected for supplying power to electrical consumers
Emergency ModeEmergency Mode
F33
G1
G1/7
M1G2K57/2
30 87
F30E
EN82
Kl. 30
Kl. 31
F32
CAN-B
-
-
+
+
F30 Polyswitch fuse F32 Front pre-fuse boxF33 Rear pre-fuse box
G1 BatteryG1/7 Auxiliary batteryG2 Alternator
K57/2 Auxiliary battery relayM1 StarterN82 Battery control module
![Page 33: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/33.jpg)
33
Auxiliary Battery Charging ModeAuxiliary Battery Charging Mode
- Battery control module detects insufficient voltage at auxiliary battery
- Auxiliary battery relay (K57/2) is activated for a short period of time if primary system voltage is above 13.5V
- Auxiliary battery is charged by alternator through auxiliary battery relay (K57/2)
- This charging cycle will only occur once per ignition cycle
-
-
+
+
F33
G1
G1/7
M1G2K57/2
30 87
F30E
EN82
Kl. 30
Kl. 31
F32
CAN-B
-
-
+
+
F30 Polyswitch fuse F32 Front prefuse boxF33 Rear prefuse box
G1 BatteryG1/7 Auxiliary batteryG2 Alternator
K57/2 Auxiliary battery relayM1 StarterN82 Battery control module
![Page 34: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/34.jpg)
34
Dual Battery System Diagram CAN BDual Battery System Diagram CAN B
N10/1 - circuit 61
N73 - ignition key inserted
N93 - diagnosis
G1 - systems battery sensing
N10/2 - trunk switch
G1/7 - auxiliary battery sensing
A1 - warning messages
![Page 35: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/35.jpg)
35
Dual Battery Service TipsDual Battery Service TipsNormalization:
If the systems battery is disconnected or dead, the following systems should bechecked for normal operation. If systems are inoperative or erratic then normalizationwill have to be performed.
Potential systems requiring normalizing are:
• ESP
• AAC - automatic air conditioning
• Windows and sunroof
• Left front seat
• Right front seat
• Steering wheel and mirrors
Adding additional electric accessories:When adding accessories always use a power supply that is fused through thepre-fuse boxes. This will ensure that the BCM can monitor the currentconsumption accurately.DO NOT CONNECT ACCESSORIES DIRECTLY TO BATTERY TERMINALS
![Page 36: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/36.jpg)
36
Dual Battery Service TipsDual Battery Service TipsNormalization:
If the systems battery is disconnected or dead, the following systems should bechecked for normal operation. If systems are inoperative or erratic then normalizationwill have to be performed.
Potential systems requiring normalizing are:
• ESP
• AAC - automatic air conditioning
• Left front seat
• Right front seat
• Steering wheel and mirrors
• Windows and sunroof
![Page 37: 319 Ho Dual Battery (Acb - Icc) 11-29-02](https://reader031.vdocuments.us/reader031/viewer/2022031613/577cc7a91a28aba711a19886/html5/thumbnails/37.jpg)
37
AppendixAppendixAH54.10-P-0002-01A Notes on AGM battery construction, and properties
AR54.10-P-1129-01A Battery test using Midtronics MCR717
OF58.40-P-3000-04A Order form for Midtronics MCR717
GF54.10-P-4201T Auxiliary battery relay, location, and function
GF54.10-P-1001T Two-battery vehicle power supply, function
GF54.21-P-4121-02T Vehicle power supply control module, task
ETM doc #
PE54.15-P-2502DA Pre-fuse F32 wiring diagram
PE54.15-P-2503DA Pre-fuse F33 wiring diagram
PE54.15-P-2501DA Pre-fuse F34 wiring diagram
WIS doc.# Topic
Internet Siteswww.midtronics.com Total battery management (AGM) charging, testing