3 flexi multi radio bts mop comms and integ concurrent mode cell c za v1 3

2G & 3G Flexi Multiradio BTS-MoP-Comms and Integ-Cell C_ZA

RU30 – CONCURRENT MODE/RF Sharing

Project Name : Cell C 900 UMTS Multiradio

Customer Name : Cell C

Document No. : 10

Version : 1.3

Document Type : Method of ProcedureDocument Number : 10Originator : Multiradio SiSo TeamReviewed By : Cornel LabuschagneApproved By : Brando B RiofloridoDate Approved : 16July2012Function : NI RSO Site Solutions – Africa Region

Type of Document Guidelines - Number Revision Number

Network Implementation Site Solutions – TI

TI HAND BOOKTI HB – MEA NI SiSo – 2010 1.3

of 61 Date: 06/27/2012

Title

2G & 3G MR Flexi BTS-MoP-Comms and Integ Concurrent Mode - Cell C_ZA

Table of Content

1. INTRODUCTION

2. CONTACT INFORMATION

3. EQUIPMENT / MODULES

4. OPTICAL CABLING

5. COMMISSIONING THE 3G FLEXI WCDMA MR BTS

6. LAUNCH THE 3G BTS SITE MANAGER

7. 3G FILES FOR DOCUMENTATION

8. 3G FLEXI WCDMA BTS INTEGRATION

9. COMMISSIONING THE 2G FLEXI EDGE MR BTS

10. LAUNCH THE 2G FLEXI EDGE SITE MANAGER

11. EXTERNAL ALARM TESTING

12. REFERENCES

13. DISTRIBUTION

14. DOCUMENT REVISION HISTORY




of 61 Date: 06/27/2012

Title


1. Introduction

This document will highlight the steps in commissioning the 2g & 3g Flexi Multiradio BTS in a Concurrent Mode/RF sharing configuration and the correct Optical cabling between the 2 System Modules (ESMB/C & FSMD/E) & RF Module (FXDA).

2. Contact Information

The following are the contact details of the key persons needed for escalation and coordination in the field as shown in Table 1 below.

Project Manager Johannes MoolmanShane Markram

+27 82 5764665+27 82 3740180

TI Manager Cornel Labuschagne +27 82 5769944OH&S Manager Johan Booysen +27 83 2760548Africa Region SEC Brando B Rioflorido +27 72 4526615

Table1. Contacts




of 61 Date: 06/27/2012

Title


3. Equipment/Modules

3.1 FSMD/E

3.2 ESMB/C

3.3 FXDA




of 61 Date: 06/27/2012

Title


4. Optical Cabling

4.1 FLEXI Multi Radio RF Sharing with RDSA (Diversity Cable)

Details:• Synchronization used is E1 – ports IF 1 from the 2G system module (ESMB/C) is

Connected to IF1 (FSMD/E)• RDSA Diversity Cables used to connect Diversity Antenna Lines for 2G and 3g

system• Power for GSM FXDA is supplied by ESMB/ESMC• Power for WCDMA FXDA is supplied by FSMD/FSME

BTS Software:• 2G BTS SW Version : EX3.1_MP2_Pre2_BL55_A51_A53• 3G BTS SW Version : WN6.0_22.12-159_B

BTS Site Manager• 2G BTS SW Manager : EX3.1_PP2.1_BL03_Site_Manager• 3G BTS SW Manager : BTSSiteEM-WN60-6.2.1417




of 61 Date: 06/27/2012

Title


4.2 FLEXI Multi Radio RF Sharing without RDSA (Concurrent Mode with 1 RF Module)

Details:• Synchronization used is Optical –3G System Moduel ( FSMD/E) ports OPT IF4

EXT1 is connected to 2G System Module (ESMB/C) OPT 4/EXT • Antenna Lines for Main and diversity is connected to single RF Module (FXDA).• Power for the shared RF Module (FXDA) is supplied by FSMD/FSME.

BTS Software:• 2G BTS SW Version : EX4.1_M1.0_BL058_A51_A53• 3G BTS SW Version : WN7.0_1104_1270_04

BTS Site Manager:• 2G BTS SW Version : EX4.1_MP1.0_2G_BTS_Site_Manager_BL055• 3G BTS SW Version : BTSSiteEM-WN70-7.1.1077




of 61 Date: 06/27/2012

Title


5. COMMISSIONING the 3G Flexi WCDMA Multiradio BTS

NOTE: During this setup, the 3G Flexi WCDMA Multiradio BTS must be the Master, in that case it should be commissioned first before commissioning the 2G Flexi Edge Multiradio BTS.

5.1 Define the laptop IP address as shown in the figure below. This will allow you to interrogate locally the 3G Flexi Multiradio equipment.

A 10base-T Ethernet cable with RJ-45 connector is used for connection to the system module (FSMD/E) LAN port.

Laptop OS should be Windows XP Home/Pro, Vista and Windows 7 (for Windows 7 & Vista, open the BTS site manager as administrator for it to work).

Nokia Flexi BTS Site Manager (BTSSiteEM-WN70-7.1.1077) should be installed in your laptop.

3G Datafill file is needed for the BTS parameters.




of 61 Date: 06/27/2012

Title


Concurrent mode/RF sharing licenses (Ru30) MUST be already installed on the BTS by the ROC/NOC before starting.

Sec4.2 of this document MUST be satisfied.

Perform back up of the existing configuration of the Flexi BTS for fall back procedure if needed.

6. Launch the BTS Site Manager

Before starting, make sure that the preparations have been made as highlighted in sec5. The following steps will guide you interrogating the BTS equipment.

1. Start the Nokia BTS Site Manager by clicking the icon on your desktop. The task selection view opens as shown below.

2. If you want to establish a local connection, select the Local option from the IP adress list.

3. If you want to establish a remote connection, define the IP address of the remote BTS.

4. Enter the Username and Password. The default username is Nemuadmin and the password is nemuuser.




of 61 Date: 06/27/2012

Title


5. Click connect.

If multiple versions of BTS Site manager are installed on the PC, the appropriate BTS Site Manager version is selected automatically.

NOTE: If there is a Failure to connect to BTS, possible cause below

- Software not compatible with new FTLB transmission Module.- Swap FTLB with FTIB and reconnect, update software as indicated

below.- When software is successfully uploaded, replace FTIB with FTLB

and reload software to continue with commissioning.

6.1 Updating the BTS Site software

Updating the BTS software is optional. You should do it only if the BTS does not have the required software version. Follow the steps below.

1. If there is mismatch in the software, a dialog box opens as shown below. Otherwise you have to go to the update SW to BTS site menu.

2. Select file button to locate the target build of the new SW as shown below and click open.

3. The current target build is TargetBD_WN7.0_1104_1270 04 .zip




of 61 Date: 06/27/2012

Title


4. Select the activate SW after update check the box to enable the activation of the new SW in accordance to SW updating. Click the update button to begin the SW update.

5. Click the close button to close the Update SW to BTS Site dialog box.




of 61 Date: 06/27/2012

Title


6. Check “SW release version: WN7.0 1104 1270 04” is loaded

Note: This exercise will also update the SW versions of the RF Module: FXDA. If any case there is “incompatible SW alarm” just reload the SW.

6.2 Manual Commissioning

Before commissioning is done, click on “Antenna line management and un-tick all “3GPP/AISG communication” boxes as indicated. This has to be done before any 3G Multi-radio commissioning starts. Ensure “Reset after sending” is enabled and send new configuration to BTS. After reset check “Antenna line management settings again to verify “3GPP/AISG communication” boxes is unchecked. Only after this proceed with commissioning

If no commissioning file(.xml) is available, Nokia Flexi Multiradio site should be commissioned manually. The Flexi Multiradio BTS and/or the flexi transport module (TRS) are commissioned with the commissioning wizard in Nokia Flexi BTS Site Manager. The commissioning can be started when the modules are on “initialised” state. Follow the steps below.




of 61 Date: 06/27/2012

Title


The wizard features back, next, cancel and help buttons for navigating. The next button brings up the following page in each commissioning file. It guides you through the commissioning process and prompts you for the required parameters.

1. Click View tab, choose the commissioning button on the view bar or choose the commissioning menu item. The commissioning introduction menu opens as shown below.

2. Choose the BTS site (will commission the BTS and TRS parameters) and choose manual commissioning type.

6.3 Define site properties

Commissioning requires that Name, BTS ID, A2EA and IP addresses are defined.

1. Enter the name of the BTS site in the name field2. Enter the location.3. Enter the description or configuration of the site as per profile in

the plan.4. Define the BTS Id ( for Cell C site name = BTS Id).5. Define the IP address of the: TRS BTS, RNC and NTP server (refer

to the example IP Plan for Cell C Project).




of 61 Date: 06/27/2012

Title


WBTS-IP Plan-PROES STREET Site RNC-3G CellC-SouthAfrica-version1 1-03 05 2010.xls

6. Pls refer to the figure as shown below.

6.4 Define security configuration

Not much is defined here as per plan. Only the ping and trace route is enabled.




of 61 Date: 06/27/2012

Title


6.5 Define the physical interface properties

We will define the Ethernet interface and use IuB IP transport mode as per high level design in this Cell C project.

- IF1 previously activated in RF sharing with diversityis now “DEACTIVATED” in Concurrent Mode. Optical Interface OPT IF4 is now used as the synchronization Source for Concurrent Mode

- EIF 2 must be checked “In Use”, speed of 100mbps full duplex mode

-EIF 3 must be checked ”In Use”, speed and duplex “Autodetect”, this parameter enables the Fast Ethernet port for Ethernet connection to 2G ESMB/C module




of 61 Date: 06/27/2012

Title


6.6 Define transport address and quality of service configuration

1. Ethernet Switching:

• Queue Weightso 1 - Stricto 2 - 8o 3 - 4o 4, 5,6 -1o 5o 6




of 61 Date: 06/27/2012

Title


• DSCP Priority Mappingo 1 – 46,48o 2 -34, 36, 38o 3 – 26, 28, 30o 4 – 10, 12, 14, 18, 20, 22o 5 – no settings

• All other parameters: default

2. VLAN Aware Configuration / Ethernet Interface Shaper

• VLAN aware switching – not in use• Ethernet Interface shaper for each Interface

o EIF 1 Egress Shaper – Speed and Duplex Ingress Rate – Speed and Duplex Speed and Duplex – Autodetect

o EIF 2




of 61 Date: 06/27/2012

Title


Egress Shaper – Speed and Duplex Ingress Rate – 100 Mbps Full duplex Speed and Duplex – Autodetect

o EIF 23 Egress Shaper – Speed and Duplex Ingress Rate – 100 Mbps Full duplex Speed and Duplex – Autodetect

3. Ethernet Link OAM - no setting needed, on this page the 2G system module is introduced, this is for testing purpose only.




of 61 Date: 06/27/2012

Title


4. Committed Information Rate Set according to planned datafill.




of 61 Date: 06/27/2012

Title


5. Define Quality of Service as follows:

• NBAP, Expedited Forwarding, DSCP 46• CES 2,3 and 4, DSCP 46• All other parameters: default

6.7 Define IP Interfaces We need to define the following transport address:

1. Transport Ethernet Interface (refer to the IP plan). The BW is 100Mbps and includes Ethernet overhead with MTU of 1500 bytes.

2. Define VLAN mapping in use. The VLAN Id = Site Id ( refer to IP Plan)




of 61 Date: 06/27/2012

Title


IP Interface:- “Total shaper information rate” define at 24.0Mbit/s- “Commited Information rate” as per RF planner/NPO configuration- “Include Ethernet overhead” checked-

IP Interface: - “New VLAN ID” and define as per RF planner/NPO configuration- “Address” define as per RF planner/NPO configuration- “Committed Information Rate” define as per RF planner/NPO configuration- “Enable QoS” checked




of 61 Date: 06/27/2012

Title


6.8 CES over PSN settings

Define “Minimum UDP port” to 49152

6.9 Define the Iub IP settings

Refer to the Datafill for “Far end SCTP subnet”, “Minimum SCTP port”, “Minimum UDP port”, “CAC committed bit rate same as ‘Commited information rate’ ” parameters. “Signalling bit rate” set to 450kbit/s and “DCN bit rate” is at 100kbit/s, “Local” and “remote UDP port”.

IP Interface:- “VLAN Type” define all as per RF planner/NPO same as VLAN of Transport

Ethernet Interface




of 61 Date: 06/27/2012

Title


6.10 Configure the Timing over Packet parameters

Refer to the Datafill for ‘Master clock address’ plan. Message rate is 16 T/S

6.11 Application Addresses

• IP addresses are reflected on this page




of 61 Date: 06/27/2012

Title


o User Plane1, Control Plane, Synchronization plane IP – same as Transport Ethernet IP address.

o Management Plane IP – same as transmission IP

6.12 RTT Measurement

• Default settings, nothing to define




of 61 Date: 06/27/2012

Title


6.13 Define synchronization timing source

1. “Timing Source Priority 1” set to “Timing over packet”

2. “Priority 2 and 3” set to default3. All other parameters set to default

6.14 Define BTS Static Route

- “Default Gateway” defined as per RF Planner/NPO datafill




of 61 Date: 06/27/2012

Title


6.15 Define IP Filtering exception rules for site support equipment

This is not defined in this project.

6.16 Define settings for BTS




of 61 Date: 06/27/2012

Title


6.17 Automatic License Distribution Settings

• Automatic licensing in use is enabled. Channel Elements are generated and we leave it as it is. No need to change.

Define:- “Configuration name” is set as per Profile # accdg to Datafill.- “Time Zone” set to (GMT+2)Africa/Johannesburg- “Transmission Sync(TDM/SuncE/Top) in use” must be checked-- “Module Locations” as per RF planner/NPO datafill




of 61 Date: 06/27/2012

Title


6.18 Concurrent Mode Settings

• RF sharing is enabled• Ensure System Module Product Code and Serial Number are filled up with the

valid data• FXDA Radio Module Connection is “ENABLED” for sharing (ESMX 1 Optical IF1)

6.19 Creating Local Resources




of 61 Date: 06/27/2012

Title


Create new cell and define the antennas that will be used for the 3/3 cells created. If 40W carrier power is used, a license is required to be downloaded before the grace period expires.

6.20 Local Cell Settings

- RNC type used for CELL C is “Nokia Siemens Network” only




of 61 Date: 06/27/2012

Title


6.21 Define the WCDMA Carrier Candidates

Local cell group is not supported therefore not defined. The carrier frequency, UARFCN, is defined for Frequency Band 900MHz -2961 (932.2Mhz) and for Frequency Band 2100MHz - 10663(2132.6Mhz) in this Cell C Project.

6.22 Define HSDPA and HSUPA settings




of 61 Date: 06/27/2012

Title


The 16QAM modulation, PFRP and shared scheduler are enabled for HSDPA. Resource Allocation should be at “16 HSDPA users per cell”. The HSUPA uses the default settings. The Iub delay threshold are define as shown in the above snapshot.

6.23 Define HSUPA settings

• HSUPA resource allocation “ enabled”• Happy Bit Ratio Measurement

o Small transmission filtering “in use”o User equipment power headroom filtering “in use”

UPH threshold is “default” no need to manually set it.o BTS processing set is “default” no need to manually set it.




of 61 Date: 06/27/2012

Title


6.24 Define HSUPA settings

1.For QoS, the default settings were used. Unless specified in this project.




of 61 Date: 06/27/2012

Title


6.25 Antenna Line Management

• No settings defined for antenna line management

6.26 Antenna Line Settings

FXDA 1/2/3/4/5/6 feeder loss is set at a value defined by RF Planner/NPO. Triplexer is used and The RTT measurement is DISABLED and define the Antenna cable length as per RF Planner/NPO. No need to define the MHA setting. Additional RX Gain 0.0dbm. Uplink Delay 85.0ns




of 61 Date: 06/27/2012

Title


6.27 No need to define settings for Siemens proprietary AI SiemSG1.1 TMARET and RET Units since RET/TMARETS are not used in this project.




of 61 Date: 06/27/2012

Title


6.28 Define settings for external fault and control lines for system module

The external alarms are defined on the 2G GSM equipment. No need to define the external alarms on the 3G equipment.




of 61 Date: 06/27/2012

Title


6.29 Send BTS Parameters to BTS

Click send parameters button to send the commissioning parameters to BTS site. After the parameters have been successfully sent, the site will reset and the new parameters are activated. The BTS and TRS will now be in a “commissioned” state. An option to save, if needed for documentation, is prompted prior to sending the parameters.

NOTE: 3G Commissioning File – is needed on the commissioning of the Flexi Multi Radio 2G System.

The commissioning file *.xml will be needed to configure the 2G BTS in order

for the 3G system and 2G system to detect and share the same RF Module.

(sample: BTS_Commissioning_Teraco_Test_BTS2_RNC2_BTS_20120605.xml)

6.30 Define additional setting

No additional settings defined as per high level design.




of 61 Date: 06/27/2012

Title


6.31 Site Tests

You can run tests on the commissioned BTS. The test results and reports are attached to the commissioning report.

For this part, only the Ethernet Test is done and saved for documentation. WCDMA loop test can be done if the site is on air or when the BTS is on Test State (if not yet integrated).




of 61 Date: 06/27/2012

Title


6.32 Commissioning Report

View the contents of the commissioning report and save the report to a file for documentation. Click finish to complete the commissioning procedure.




of 61 Date: 06/27/2012

Title


7. Files for documentation

7.1 Site information

This file contains all the details of the hardware elements installed at site. This is needed in the BTS site folder documentation. From the tool tab, check the site information menu and save the data.

7.2 Snapshot

This data contains the site log files and settings of the TRS and BTS. From the File Tab, choose Snapshot menu and save the data.




of 61 Date: 06/27/2012

Title


7.3 IP connectivity Test

This test will verify the IP routing of the BTS. Ping the remote address (RNC, NTP server, Timing over Packet, BTS routing gateway) and if there is no connectivity, this test fails. This can be done on the commissioned state of the BTS prior to integration. Click the Tool Tab and choose IP connectivity test.




of 61 Date: 06/27/2012

Title


8. 3G Flexi Multiradio BTS Integration

8.1 Pre-requisites

1. The BTS and TRS are commissioned; all parameters needed are configured as per plan.

2. The IP connectivity test Passed. Ping test of the remote address is possible.

3. Site parameters, DCN, Connection Configuration and AAL2 user planes have been configured in RNC.

4. Call NOC to download Licence’s and Unlock the Site. See status below.

7. COMMISSIONING the 2G Flexi EDGE MULTIRADIO BTS

NOTE: on the 2G BTS, First thing to be done is to run “Undo Commissioning & remove Traffic Bypass capacity” to ensure all data is cleared from the flash memory.

9.1 Define the laptop IP address as shown in the figure below. This will enable you to interrogate the 2G Flexi Multi Radio BTS equipment.




of 61 Date: 06/27/2012

Title


A 10base-T straight Ethernet LAN cable with rj-45 connector is used for connection to the system module (ESMB/ESMC) LMP port.

2g Flexi BTS Site Manager (EX4.1_MP1.0_2G_BTS_Site_Manager_BL055) should be installed in your laptop with the latest BTS SW release (EX4.1_M1.0_BL058_A51_A53).

Laptop OS should be Windows XP Home/Pro, Vista and Windows 7 (for Windows 7 & Vista, open the BTS site manager as administrator for it to work).

Updated file for BTS parameters e.g. site id, bcf id, configuration, A-BIS plan etc. This should be provided by Network Planning.

3G Commissioning file (XML) previously saved from the 3g commissioning earlier.

Sec4.2 of this document MUST be satisfied.

Perform back up of the existing configuration of the Flexi BTS for fall back procedure if needed.




of 61 Date: 06/27/2012

Title


8. Launch the 2g Flexi BTS Site Manager

Before starting, make sure that the preparations have been made as highlighted in sec4. The following steps will guide you interrogating the BTS equipment.

Start the Nokia 2G Flexi BTS Manager by clicking the icon on your desktop. The task selection view opens as shown below.

10.1 BTS SW Update

The first step of the commissioning is BTS SW Downloading/Update. This is necessary to align the current SW packet of the BTS with the new release BTS SW. It starts with selecting the “BTS SW” and followed by “SW update”

Then, we must browse and select the “header” or “master” file to start the download. The SW version BTSM4113.3A




of 61 Date: 06/27/2012

Title


It is recommended to select the option “Forcé Download” to guarantee the downloading of all files of the new SW. If we don’t mark this option, only the changes in between versions will be downloaded (depending on the versions).

Press the “update SW”. The progress bar will help us to follow the process. Notice that FIREWALL SW running on PC could BLOCK the downloading. When the Download is finished, The BTS will restart and the PC automatically connect to the BTS. Multi Radio BTS doesn’t autodetect un-commissioned radio modules, thats the reason why only the system module appears on the screen.

ON-LINE commissioning is when you are physically connected to the BTS via your straight LAN cable.

Check ‘Force BTS Download All Application Files’




of 61 Date: 06/27/2012

Title


10.2 Perform “Undo Commissioning of BTS”

This will last a few minutes and when finished, the BTS will restart. Notice that any change in the BTS configuration needs a BTS reset to be effective.

This will last a few minutes and when finished, the BTS will restart. Notice that any change in the BTS configuration needs a BTS reset to be effective.

NOTE: 3g Commissioning file(XML) is needed to be downloaded into the 2g Flexi Multiradio BTS.

After restarting, we choose again “commissioning wizard” and then “Commission manually” to bring you to the Site Specific Information.

10.3 Site Specific Information




of 61 Date: 06/27/2012

Title


Just populate the BCFID of the site, then proceed to the next step.

10.4 Hardware configuration

Specify from file and browse the 3G commissioning file (XML) earlier saved then proceed to the next step.

10.5 Module configuration




of 61 Date: 06/27/2012

Title


Note that OPT1 is untick and your synchronization is also untick since your 3G BTS is your master. Note also that the RF module (FXDA) is already defined.

If DCS1800 is being used, then we need to add new RF chain for FXEA using OPT2.

10.6 Local Sector Settings

Since we hav Rx Sharing of FXDA (sector 4,5 & 6), the máximum allowable Carrier power is 60W. Since 3G BTS uses 40W carrier power already, our 2G BTS will now have a máximum of 20W carrier power to be used. It can be 10W depending on the RF plan. While your FXEA (sector 1,2 &3) will still have a máximum 60W carrier power since its not shared.




of 61 Date: 06/27/2012

Title


10.7 Antenna Settings




of 61 Date: 06/27/2012

Title


Associated antennas are defined for the FXDA and FXEA. Antenna settings use default values.

10.8 RET Settings

RETs are not used therefore this are not defined.




of 61 Date: 06/27/2012

Title


10.9 FRM EAC Settings

FRM EAC settings are not used therefore this are not defined.

10.10 BBU Settings

No BBU used therefore this are not defined.

10.11 Passive Unit Settings




of 61 Date: 06/27/2012

Title


FSEB box is defined with its serial number, Product code is self-generated.

10.12 Transmission Parameter Settings

Transmission parameter is specified manually by choosing the correct TRS PIU.




of 61 Date: 06/27/2012

Title


10.13 Network Settings

Packet Switched Network is used with transmission mode as PWE.

10.14 Ethernet Settings

EIF1 is enabled for the BTS transmission.




of 61 Date: 06/27/2012

Title


10.15 PWE Settings

PWE1 and PWE2 is enabled and the UDP ports are populated as per plan.

10.16 Tunnel Settings




of 61 Date: 06/27/2012

Title


Tunnel settings of the PWE1 and PWE2 are populated according to plan.

10.17 Ethernet OAM Settings

This setting is not defined.




of 61 Date: 06/27/2012

Title


10.18 Synchronization Settings

TOP is enabled and Master clock IP address is populated (same as what is defined in the 3G BTS). PWE1 and PWE2 are defined as priority1 & 2 respectively.

10.19 ABIS Termination

Enable ABIS mapping and allow ABIS allocations from BTS Manager




of 61 Date: 06/27/2012

Title


10.20 ABIS Allocation

Populate the Abis Allocation as per ABIS plan per PWE for 900 and 1800 BTS.

10.21 Ethernet Monitoring

Ethernet monitoring is not defined in this BTS.




of 61 Date: 06/27/2012

Title


10.22 Local Management Port settings

This BTS setting is not defined.

10.23 Send SCF to BTS

Save the SCF before sending it to the BTS.




of 61 Date: 06/27/2012

Title


Commissioning in Progress

BTS will reset once completed

Local commissioning completed successfully and ‘O&M Link Established’




of 61 Date: 06/27/2012

Title


Fetching the commissioning report




of 61 Date: 06/27/2012

Title


Site Information

9. External Alarm Testing

Indoor Sites

Once the BTS is commissioned, test the alarms with the NOC. Ask the NOC to save and email you the log file. The Alarms will be tested twice. First before moving the Alarm cable and second when the alarm cable is moved. Ensure that the alarms on the old BTS are the same as on the MR BTS. Please note that not all the sites will have the same alarms. The most common alarms are listed below. If the alarm is not listed below simulate the alarm to test that it is functional.

1. Intruder (External Alarm 18)Close the door and monitor on BTS manager for alarm to clear.Open door and monitor to alarm condition

2. Movement(if installed) (External Alarm 19)Cover movement sensor and wait for at least 3 minutes.Remove cover from sensor and monitor alarm condition.

3. Rectifier Module Fail(External Alarm 8)Switch off rectifier module at rectifier or disconnect module to generate

alarm.Switch on again and see that alarm clears.

4. High Temp(External Alarm 7)Warm-up the sensor near the aircon control box to generate an alarm. Extractor fan will activate




of 61 Date: 06/27/2012

Title


Wait for sensor to cool down and alarms will clear.

5. AC Mains Fail(External Alarm 2)Switch off AC Mains breaker inside container to generate an alarm. The rectifier alarms will alsocome on.Switch on AC Mains breaker to clear the alarms.

6. Rec SYS/Batt Low(External Alarm 3)Switch off rectifier module at rectifier or disconnect module to generate


7. Smoke(External Alarm 17)Make some smoke and hold it near the smoke sensor. The light will come on and all aircons willswitch off.Remove the sensor by unscrewing it and put it back again. The alarm will

clear.

8. Aircon Fail(External Alarm 9)Switch of aircons at the AC DB to generate alarms.Switch on to clear the alarms

9. DC Low/Batt Low(External Alarm 4)Switch off rectifier module at rectifier or disconnect module to generate


10. Dual Aircon(External Alarm 5)Aircon alarm will activate when temp inside container exceeds 28degCClose container door and wait +/- 10 min before entering and see if alarm

clears

11. DC High/Rectifier SYS(External Alarm 6)Switch off rectifier module at rectifier or disconnect module to generate


Outdoor Sites

Once the BTS is commissioned, test the alarms with the NOC. Ask the NOC to save and email you the log file. The Alarms will be tested twice. First before moving the Alarm cable and second when the alarm cable is moved. Ensure that the alarms on the old BTS are the same as on the MR BTS. Please note that not all the sites will have the same alarms. The most common alarms are listed below. If the alarm is not listed below simulate the alarm to test that it is functional.

1. Intruder (External Alarm 18)Close the DELTA cabinet door and monitor on BTS manager for alarm to

clear.Open DELTA cabinet door and monitor to alarm condition




of 61 Date: 06/27/2012

Title


2. Rectifier Module Fail(External Alarm 8)Switch off rectifier module at rectifier or disconnect module to generate


3. High Temp(External Alarm 7)Warm-up the sensor behind the DELTA rectifier control box to generate an

alarm. Wait for sensor to cool down and alarms will clear.

4. AC Mains Fail(External Alarm 2)Switch off AC Mains breaker inside DELTA Rectifier to generate an alarm. The rectifier alarms will also come on.Switch on AC Mains breaker to clear the alarms.

5. DC Low/Batt Low(External Alarm 4)Switch off rectifier circuit breaker at DELTA rectifier or disconnect module to generate alarm.Switch on again and see that alarm clears.

10. References

2G/3G Flexi Multiradio Commissioning

11. Distribution

NSN TI Manager, Cell CNI SISO Manager, Africa

12. Document Revision History

DATE Revision No

Summary of changes

25Jan2012

V1.2 Revised the antenna line settings for FXDA

26June2012

V1.3 Added Module Photos cabling (item 3)

Added RF cabling (item 4)Revised SW VersionsRevised antenna line settingsCommissioning File (4.25)

3 flexi multi radio bts mop comms and integ concurrent mode cell c za v1 3

Documents

g files

g mr flexi btsmop

g bts site manager7

g bts sw manager

g flexi multiradio btsmop

g bts sw version

g flexi wcdma bts integration9

g system power