13149 toyota rav 4 (excluding electric) · 2020. 3. 26. · toyota rav 4 (excluding electric)...
TRANSCRIPT
-
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation ofthis product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental orconsequential loss or damage.
3,500 5254,000 525
TOYOTA RAV 4 (EXCLUDING ELECTRIC)3/26/2020
13149
30
34
15
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
Parts ListDESCRIPTIONPART NUMBERQTYITEM
HHCS,M12x1.25,35,CL10.9,YZ10-1027541WASHER,S-CON,1/2,YZ30-0014942
1. If present remove panel and trim using panel trim diagram above as reference. Remove tie down bracket from the driver's side of the vehicle and return to vehicle owner.
2. Lower rear most exhaust isolator for ease of installment.
3. Raise hitch into position over existing weldnuts and install the supplied 12mm hex bolts and conical tooth washers as shown.
4. Raise exhaust back into location and reinstall rubber isolator.
5. Torque hardware to 86 lb-ft.
PASSENGER SIDEFRAME RAIL
EXISTING WELDNUTS (BOTH SIDES)
TOOLS REQUIRED17, 19mm SOCKET
8" EXTENSIONSOCKET WRENCHTORQUE WRENCH
- EXISTING WELDNUTS- NO DRILLING REQUIRED- REMOVE TIE DOWN BRACKET- LOWER EXHAUST
1
2
DRIVER SIDE FRAME RAIL
USE RIB AS GUIDEPANEL TRIM DIAGRAM
1.500 in
-
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replacethe product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacementof products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.15
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: EASY
EASY MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be worn at all times whileinstalling this product.
YEARS: 2006-CURRENT TOYOTA MODEL: RAV4 (EXCEPT ELECTRIC) COMPACT SUV
3,500525
TRAILER WEIGHT:TONGUE WEIGHT:
13149 INSTALLATION INSTRUCTIONS
LBS.LBS.
3/26/2020
WEIGHT DISTRIBUTION: TRAILER WEIGHT:TONGUE WEIGHT:
4,000525
LBS.LBS.
MIN.30
IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME: PRO INSTALL TIME:
SOCKETS
17mm19mm
WIRE PIPEBRUSH
RATCHET
TORQUEWRENCH
SOCKETEXTENSION
8"
PART REMOVAL
CLEAN EXISTING WELD NUTS USING A PIPE BRUSH
NO DRILLING RQUIRED
REMOVE TIE DOWN BRACKET
LOWER EXHAUST
-
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
DESCRIPTIONPART NUMBERQTYITEMHHCS,M12x1.25,35,CL10.9,YZ10-1027541WASHER,S-CON,1/2,YZ30-0014942
1. If present remove panel and trim using panel trim diagram below as reference. Remove the tie down bracket from the drivers side frame rail using the 17mm socket, 8" extension and ratchet. Return the bracket and fasteners to vehicle owner.
2. Lower rear most exhaust isolator for ease of installment.
2
1
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
EXISTING WELDNUTS(BOTH SIDES)
PANEL TRIM DIAGRAM
1.500 in USE RIBAS GUIDE
-
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Raise hitch into position over existing weldnuts and install the supplied 12mm hex bolts and conical tooth washers as shown.
4. Raise exhaust back into location and reinstall rubber isolator.
5. Torque hardware to 86 lb-ft.
Install now complete
-
TOWING SAFETY INFORMATION
13149-INS BW13149-INS COLOR