1 radiation effects in devices and technologies federico faccio cern – ph dept/ese group...
TRANSCRIPT
11
Radiation effects in Radiation effects in devices and technologiesdevices and technologies
Federico FaccioFederico Faccio
CERN – PH dept/ESE groupCERN – PH dept/ESE group
[email protected]@cern.ch
EIROforum 09 Federico Faccio - CERN 22
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID) Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 33
Summary of radiation effectsSummary of radiation effects
Cumulative effects
Single Event Effects (SEE)
Total Ionizing Dose (TID)Potentially all components
Displacement damageBipolar technologies
OptocouplersOptical sources
Optical detectors (photodiodes)
Permanent SEEsSEL
CMOS technologies
SEBPower MOSFETs, BJT and diodes
SEGRPower MOSFETs
Static SEEsSEU, SEFI
Digital ICs
Transient SEEsCombinational logicOperational amplifiers
EIROforum 09 Federico Faccio - CERN 44
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID)
TID in CMOS technologiesTID in CMOS technologies TID in bipolar technologiesTID in bipolar technologies
Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 55
TID in MOS structuresTID in MOS structures
Poly
SiO2
Si
e h
1
+
-V
e
h
2
+
-V
Trapped chargeALWAYS POSITIVE!
hhh h
3
+
-V
4
Interface statesCan trap both e- and h+
hhh h
+
-V
EIROforum 09 Federico Faccio - CERN 66
Contributions to the VContributions to the VTT shift shift
Oxidecharges
Interfacestates
n-channel p-channel
+
I 1
Before irradiation
VGS
ID
VT10
I 2
VT2VT2
N-channel
I 1
Before irradiation
-VGS
ID
VT10
P-channel
EIROforum 09 Federico Faccio - CERN 77
Different evolution of defectsDifferent evolution of defects- All charge trapped in the oxide or in the interface states affect the - All charge trapped in the oxide or in the interface states affect the electric field across the oxide (hence the Vt of the structure).electric field across the oxide (hence the Vt of the structure).- The evolution of charge trapping and interface state formation during - The evolution of charge trapping and interface state formation during and after irradiation is different. This is very relevant for the overall and after irradiation is different. This is very relevant for the overall evolution of the measured behavior.evolution of the measured behavior.
- Annealing, or self-healing, is typically driven by thermal energy or hopping - Annealing, or self-healing, is typically driven by thermal energy or hopping of carriers from the Si layer (only about 3nm range). It is normally effective for of carriers from the Si layer (only about 3nm range). It is normally effective for trapped charge only, not for interface states (exception recently pointed out trapped charge only, not for interface states (exception recently pointed out for thick field oxides)for thick field oxides)
-50
-40
-30
-20
-10
0
10
20
30
40
50
1.E+04 1.E+05 1.E+06 1.E+07 1.E+08
TID (rd)
DV
(V
)
Example: very thick oxide NMOS
Contrib from charge trapped in oxide
Contrib from interface states
Net effect on Vth
EIROforum 09 Federico Faccio - CERN 88
Bias dependenceBias dependenceBias condition during irradiation is VERY relevant for the Bias condition during irradiation is VERY relevant for the radiation effects. During irradiation, the worst-case bias radiation effects. During irradiation, the worst-case bias condition “pushes” holes towards the Si-SiOcondition “pushes” holes towards the Si-SiO22 interface. interface.
RULE: Power circuits in their operational condition, or a RULE: Power circuits in their operational condition, or a condition known to be worst-case!condition known to be worst-case!
-0.160
-0.140
-0.120
-0.100
-0.080
-0.060
-0.040
-0.020
0.000
1.E+05 1.E+06 1.E+07TID (rad)
Vth
(V
)
Vgs=VddVgs=Vdd/2Vgs=0V
Example: Vth shift of NMOS in 3 different bias conditions
CMOS 130nm techCMOS 130nm techW/L=0.16/0.12umW/L=0.16/0.12um
The larger the positive bias, The larger the positive bias, the larger the Vth shiftthe larger the Vth shift
EIROforum 09 Federico Faccio - CERN 99
Transistor level leakageTransistor level leakage
Bird’s beak
Field oxide
Parasitic MOS
Trapped positive charge
Parasitic channel
Source
Drain
EIROforum 09 Federico Faccio - CERN 1010
TID effects and tTID effects and toxox
N.S. Saks et al., IEEE TNS, Dec. 1984 and Dec. 1986
Damage decreases with oxide thickness
Oxide trapped charge Interface states
EIROforum 09 Federico Faccio - CERN 1111
BIRD’S BEAKS
Transistor level leakageTransistor level leakage
log ID
VGS
GATE
“CENTRAL” (main) MOS TRANSISTOR
This is for LOCOS, very similar for STI
EIROforum 09 Federico Faccio - CERN 1212
Transistor level leakage: exampleTransistor level leakage: example
1.E-13
1.E-12
1.E-11
1.E-10
1.E-09
1.E-08
1.E-07
1.E-06
1.E-05
1.E-04
1.E-03
1.E-02
-1 -0.5 0 0.5 1 1.5 2 2.5 3 3.5
VG [V]
I D [
A]
Prerad
After 1 Mrad
NMOS - 0.7 m technology - tox = 17 nm
Threshold voltage shiftA!
EIROforum 09 Federico Faccio - CERN 1313
IC level leakageIC level leakage
POLYSILICON
N+ WELL CONTACT N+ SOURCEOXIDE
N WELL
SUBSTRATE
VDD SSV
++ + + + + + + + + + + ++
+
LEAKAGE
The charges trapped in the thick oxide (LOCOS or STI) decrease the Vth of the The charges trapped in the thick oxide (LOCOS or STI) decrease the Vth of the MOS structure, and the p substrate can be inverted even in the absence of an MOS structure, and the p substrate can be inverted even in the absence of an electric field. A leakage current can appear.electric field. A leakage current can appear.
EIROforum 09 Federico Faccio - CERN 1414
TID-induced failureTID-induced failure In modern technologies, leakage In modern technologies, leakage
current is typically the killercurrent is typically the killer
EIROforum 09 Federico Faccio - CERN 1515
TID in CMOSTID in CMOS
Main transistor:Main transistor: Threshold voltage shift, transconductance and noise degradationThreshold voltage shift, transconductance and noise degradation Effects get negligible in modern deep submicron (as from 250-180 nm techs)Effects get negligible in modern deep submicron (as from 250-180 nm techs)
Parasitic leakage paths:Parasitic leakage paths: Source – drain leakageSource – drain leakage Leakage between devicesLeakage between devices This are still potentially deleterious – although things looks to be better as from This are still potentially deleterious – although things looks to be better as from
130nm techs130nm techs
Summary of the problemsSummary of the problems
EIROforum 09 Federico Faccio - CERN 1616
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID)
TID in CMOS technologiesTID in CMOS technologies TID in bipolar technologiesTID in bipolar technologies
Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 1717
Bipolar transistorsBipolar transistors
Current Gain = = IC / IB
gm = IC/t
B
C
E
EIROforum 09 Federico Faccio - CERN 1818
TID in bipolar devicesTID in bipolar devicesSubstrate, sidewall and surface inversion (in oxide-isolated processes)Substrate, sidewall and surface inversion (in oxide-isolated processes)
R.L.Pease et al., IEEE Trans. Nucl. Science. Vol.32, N.6, 1985
E.W.Enlow et al., IEEE Trans. Nucl. Science. Vol.36, N.6, 1989
EIROforum 09 Federico Faccio - CERN 1919
TID in bipolar devicesTID in bipolar devices
Gain degradation:Gain degradation:Increase of the surface component of the Increase of the surface component of the base currentbase current
R.N.Nowlin et al., IEEE Trans. Nucl. Science. Vol.39, N.6, 1992
EIROforum 09 Federico Faccio - CERN 2020
ELDR effects in bipolarsELDR effects in bipolars
A.H.Johnston et al., JPL internal report, 1999
Larger degradation can be observed at low dose rate, which can not be simply Larger degradation can be observed at low dose rate, which can not be simply anticipated with laboratory testsanticipated with laboratory tests
EIROforum 09 Federico Faccio - CERN 2121
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID) Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 2222
Displacement in bipolar devicesDisplacement in bipolar devices
Displacement damage equation:Displacement damage equation:1/ - 1/0 = / [K(2fT)]
0 i is the pre-rad value, s the pre-rad value, is the value at a cumulative fluence is the value at a cumulative fluence NB: The majority of linear ICs are still manufactured in old NB: The majority of linear ICs are still manufactured in old junction-isolated processes, BUT using less conservative junction-isolated processes, BUT using less conservative approaches (more PNP transistors used in critical places)approaches (more PNP transistors used in critical places)
Gain degradation due to increased Gain degradation due to increased recombination of minority carriers in the recombination of minority carriers in the basebase
Results on biased and unbiased Results on biased and unbiased devices are almost identicaldevices are almost identical
EIROforum 09 Federico Faccio - CERN 2323
Displacement in bipolar devicesDisplacement in bipolar devicesEffects for lateral and substrate PNPEffects for lateral and substrate PNP
B.G.Rax et al., to be published in IEEE Trans. Nucl. Science, Vol.46, n.6, December 1999
Displacement damage effects are generally negligible below 3·10Displacement damage effects are generally negligible below 3·101010 p/cmp/cm22 (50MeV) also for PNP transistors (50MeV) also for PNP transistors
At levels above about 3·10At levels above about 3·101111 p/cm p/cm22 , they start to become significant , they start to become significant also for NPN transistorsalso for NPN transistors
B.G.Rax et al., to be published in IEEE Trans. Nucl. Science, Vol.46, n.6, December 1999
EIROforum 09 Federico Faccio - CERN 2424
Bipolar technologiesBipolar technologies
Displacement damage degradation
Voltage regulators, comparators, op amps
TIDLeakage paths and degradation
Sensitive with dose rate effectsVariable failure levels
Simultaneous effects:they add up
EIROforum 09 Federico Faccio - CERN 2525
Displacement in bipolar devices: Displacement in bipolar devices: exampleexample
LM117 positive voltage regulator; effect LM117 positive voltage regulator; effect of TID and displacement add up!of TID and displacement add up!
B.G.Rax et al., to be published in IEEE Trans. Nucl. Science, Vol.46, n.6, December 1999
EIROforum 09 Federico Faccio - CERN 2626
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID) Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 2727
Ionization from different radiationIonization from different radiation Traceable to the energy deposition initiated by one single particle, in a precise instant in Traceable to the energy deposition initiated by one single particle, in a precise instant in
time. Due to its stochastic nature, this can happen at any time – even at the very time. Due to its stochastic nature, this can happen at any time – even at the very beginning of the irradiationbeginning of the irradiation
Which particles can induce SEEs? In the figure below, a schematic view of the density of Which particles can induce SEEs? In the figure below, a schematic view of the density of e-h pairs created by different radiation is shown.e-h pairs created by different radiation is shown.
Heavy Heavy IonIon
eehh eehh
eehh
eehh
eehheehh eehh eehh eehh eehh eehheehh eehh eehhhh
hhhh ee
eeeeeeeeeeeeee
hhhhhhhhhh
hhhhhh
hhhhhhhhhhhh
ee
ee
eeeeeeeeeeeeeehh
eehhhhhhhhhh eeeeeeeeee
eeeeeehhhhhhhhhhhh
iiNeutronNeutron
nn
eehh eehh eehheehh eehheehh
eehh
pp
nnii
nn
ProtonProton
eehh
eehh
eehh
eehh
eehheehh
pp
eehh eehh eehheehh eehheehh
eehh
pp
nnii
pp
Small density of e-h Small density of e-h pairspairs
Large density of e-h Large density of e-h pairspairs
Small (proton) or no (neutron) density for direct ionization. Small (proton) or no (neutron) density for direct ionization. Possible high density from Heavy Ion produced from Possible high density from Heavy Ion produced from nuclear interaction of the particle with Silicon nucleus.nuclear interaction of the particle with Silicon nucleus.
Photon (X, Photon (X, ))
eehh
SiliconSilicon
Nuclear Nuclear interactioninteraction
EIROforum 09 Federico Faccio - CERN 2828
Density of e-h pairs is important (1)Density of e-h pairs is important (1) Not all the free charge (e-h pairs) generated by radiation contributes to Not all the free charge (e-h pairs) generated by radiation contributes to
SEEs. Only charge in a given volume, where it can be collected in the SEEs. Only charge in a given volume, where it can be collected in the relevant amount of time by the appropriate circuit node, mattersrelevant amount of time by the appropriate circuit node, matters
Heavy IonHeavy Ion
eehh eehh
eehh
eehh
eehheehh eehh eehh eehh eehh eehheehh eehh eehhhh
hhhh ee
eeeeeeeeeeeeee
hhhhhhhhhh
hhhhhh
hhhhhhhhhhhh
ee
ee
eeeeeeeeeeeeeehh
eehhhhhhhhhh eeeeeeeeee
eeeeeehhhhhhhhhhhh
NwellNwell
p- siliconp- silicon
p+p+
1.1.
1. Ion strike: ionization takes 1. Ion strike: ionization takes place along the track (column place along the track (column of high-density pairs)of high-density pairs)
ee
hh
ee
hh
eehh
eehh
eehh
eehhee
hh
eehh eehh
ee
hh eehh
ee
hhee
hh
ee
hh
hh
hhhheeeeeeeeeeeeee ee
hh
hh
hhhhhh
hh
hhhhhhhhhhhh
hhhh
ee eeee eeee
eeeeee
hhee
hhhhhhhhhh
ee
ee ee
ee
eeeehhhhhhhhhhhh
++--
2.2.
2. Charges start to migrate in the electric 2. Charges start to migrate in the electric field across the junctions. Some drift (fast field across the junctions. Some drift (fast collection, relevant for SEEs), some collection, relevant for SEEs), some diffuse (slow collection, less relevant for diffuse (slow collection, less relevant for SEEs)SEEs)
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
ee
hh
hh
hhhh
eeeeeeeeeeeeee
ee
hh
hh
hhhhhh
hh
hhhhhhhhhhhh
hhhh
ee eeee eeee
ee
ee
ee
hh
ee
hhhhhhhhhh
ee
ee ee
eeee
ee
hhhhhhhhhhhh
++--
3.3.
3. Charges are collected at circuit 3. Charges are collected at circuit nodes. Note that, if the relevant nodes. Note that, if the relevant node for the SEE is the p+ node for the SEE is the p+ diffusion, not all charge deposited diffusion, not all charge deposited by the ion is collected there. by the ion is collected there.
EIROforum 09 Federico Faccio - CERN 2929
Density of e-h pairs is important (2)Density of e-h pairs is important (2)
Heavy IonHeavy Ion
eehh eehh
eehh
eehh
eehheehh eehh eehh eehh eehh eehheehh eehh eehhhh
hhhh ee
eeeeeeeeeeeeee
hhhhhhhhhh
hhhhhh
hhhhhhhhhhhh
ee
ee
eeeeeeeeeeeeeehh
eehhhhhhhhhh eeeeeeeeee
eeeeeehhhhhhhhhhhh
NwellNwell
p- siliconp- silicon
p+p+
Of all e-h pairs created by radiation, only those in (roughly) this volume Of all e-h pairs created by radiation, only those in (roughly) this volume are collected fast enough to contribute to an SEE at the node are collected fast enough to contribute to an SEE at the node corresponding to the p+ diffusion (for instance, S or D of a PMOS FET). corresponding to the p+ diffusion (for instance, S or D of a PMOS FET). Density of pairs in this region determines if the SEE takes place or not!Density of pairs in this region determines if the SEE takes place or not!This is called the “SENSITIVE VOLUME” (SV)This is called the “SENSITIVE VOLUME” (SV)
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E+05
1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 1.E+08 1.E+09
Energy [eV]
Sto
pp
ing
po
wer
(d
E/d
X)
[MeV
cm2/
g]
electron
proton
He (alpha)
Si
The density of pairs depends on the stopping power of the particle, or dE/dx, or The density of pairs depends on the stopping power of the particle, or dE/dx, or Linear Energy Transfer (LET)Linear Energy Transfer (LET). . The figure above (right) shows this quantity in Si for different particles. Even protons, at their maximum stopping The figure above (right) shows this quantity in Si for different particles. Even protons, at their maximum stopping power, can not induce SEE in electronics circuits. Only ions, either directly from the radiation environment or from power, can not induce SEE in electronics circuits. Only ions, either directly from the radiation environment or from nuclear interaction of radiation (p, n, …) in Silicon can deposit enough energy in the SV to induce SEEs.nuclear interaction of radiation (p, n, …) in Silicon can deposit enough energy in the SV to induce SEEs.
Warning: data Warning: data points are points are approximate approximate in this figurein this figure
EIROforum 09 Federico Faccio - CERN 3030
Single Event Upset (SEU) (1)Single Event Upset (SEU) (1)
The e-h pairs created by an ionizing particle can be collected by a junction The e-h pairs created by an ionizing particle can be collected by a junction that is part of a circuit where a logic level is stored (logic 0 or 1). This can that is part of a circuit where a logic level is stored (logic 0 or 1). This can induce the “flip” of the logic level stored. This event is called an “upset” or a induce the “flip” of the logic level stored. This event is called an “upset” or a “soft error”.“soft error”.This typically happens in memories and registers. The following example is This typically happens in memories and registers. The following example is for an SRAM cell.for an SRAM cell.
GNDGND
VDD VDD
Node stroke Node stroke by the by the particleparticle
p- substratep- substrate
Striking particleStriking particle
Depletion region: e-h pairs are collected by Depletion region: e-h pairs are collected by n+ drain and substrate => those collected n+ drain and substrate => those collected by the drain can contribute to SEUby the drain can contribute to SEU
n+ drainn+ drain e-h pairs in this region recombine e-h pairs in this region recombine immediately (lots of free electrons immediately (lots of free electrons available in this n+ region)available in this n+ region)
High density of e-h pairs in this region can High density of e-h pairs in this region can instantaneusly change effective doping in instantaneusly change effective doping in this low-doped region, and modify electric this low-doped region, and modify electric fields. This is called “funneling”. Charge fields. This is called “funneling”. Charge can hence be collected from this region to can hence be collected from this region to the n+ drain, although a portion of it will the n+ drain, although a portion of it will arrive “too late” to contribute to SEUarrive “too late” to contribute to SEU
EIROforum 09 Federico Faccio - CERN 3131
Single Event Upset (SEU) (2)Single Event Upset (SEU) (2)
GNDGND
VDD VDD
1. Initial condition 1. Initial condition (correct value stored)(correct value stored)
00
11
Charge collected at the drain of NMOS T1 tends Charge collected at the drain of NMOS T1 tends to lower the potential of the node B to gnd. to lower the potential of the node B to gnd. PMOS T2 provides current from Vdd to PMOS T2 provides current from Vdd to compensate, but has a limited current capability. compensate, but has a limited current capability. If the collected charge is large enough, the If the collected charge is large enough, the voltage of node B drops below Vdd/2voltage of node B drops below Vdd/2
T1T1
T2T2
Node BNode B
Node ANode A
GNDGND
VDD VDD
2. Final condition 2. Final condition (wrong value stored)(wrong value stored)
11
00
When node B drops below Vdd/2, the other When node B drops below Vdd/2, the other inverter in the SRAM cell changes its output inverter in the SRAM cell changes its output (node A) to logic 1. This opens T2 and closes T1, (node A) to logic 1. This opens T2 and closes T1, latching the wrong data in the memory cell. latching the wrong data in the memory cell.
T1T1
T2T2
Node BNode B
Node ANode A
EIROforum 09 Federico Faccio - CERN 3232
““Digital” Single Event Transient (SET)Digital” Single Event Transient (SET)
Particle hit in combinatorial logic: with modern fast Particle hit in combinatorial logic: with modern fast technologies, the induced pulse can propagate through technologies, the induced pulse can propagate through the logic until it is possibly latched in a registerthe logic until it is possibly latched in a register
Latching probability proportional to clock frequencyLatching probability proportional to clock frequency Linear behaviour with clock frequency is observedLinear behaviour with clock frequency is observed
SET
SEU
Total Error = SET + SEU
Err
ors
Frequency
Register
Combinatorial logic
EIROforum 09 Federico Faccio - CERN 3333
SEU cross-section (1)SEU cross-section (1) Sensitivity of a circuit to SEU (or in general to any SEE) is Sensitivity of a circuit to SEU (or in general to any SEE) is
characterized by a cross-sectioncharacterized by a cross-section The cross-section contains the information about the probability The cross-section contains the information about the probability
of the event in a radiation environmentof the event in a radiation environment
Example: what is the error rate of an SRAM in a beam of 100MeV protons Example: what is the error rate of an SRAM in a beam of 100MeV protons of flux 10of flux 1055 p/cm p/cm22s?s?
1. Take the SRAM and irradiate 1. Take the SRAM and irradiate with 100MeV proton beam. To get with 100MeV proton beam. To get good statistics, use maximum flux good statistics, use maximum flux available (unless the error rate available (unless the error rate observed during test is too large, observed during test is too large, which might imply double errors are which might imply double errors are not counted => error in the not counted => error in the estimate)estimate)
SRAMSRAM100MeV 100MeV protonsprotons
2. Count the number of errors 2. Count the number of errors corresponding to a measured corresponding to a measured fluence (=flux x time) of particles fluence (=flux x time) of particles used to irradiateused to irradiate
Example:Example:N of errors = 1000N of errors = 1000Fluence = 10Fluence = 101212 p/cm p/cm22
Cross-section (Cross-section ()= N/F = 10)= N/F = 10-9-9 cm cm22
3. Multiply the cross-section for the 3. Multiply the cross-section for the estimated flux of particles in the estimated flux of particles in the radiation environment. The result is radiation environment. The result is directly the error rate, or number of directly the error rate, or number of errors per unit time.errors per unit time.
If (If () = 10) = 10-9-9 cm cm22
and flux = 10and flux = 1055 p/cm p/cm22ss
Error rate = 10Error rate = 10-4-4 errors/s errors/s
EIROforum 09 Federico Faccio - CERN 3434
SEU cross-section (2)SEU cross-section (2) In reality, things are generally more difficult – the real radiation environment is a In reality, things are generally more difficult – the real radiation environment is a
complex field of particlescomplex field of particles One needs models to translate cross-sections measured at experimental One needs models to translate cross-sections measured at experimental
facilities (protons or heavy ions beams) into error rates in the fieldfacilities (protons or heavy ions beams) into error rates in the field The better the experimenter knows the sensitivity of the circuit, the better The better the experimenter knows the sensitivity of the circuit, the better
he/she can estimate the error rate in the real environmenthe/she can estimate the error rate in the real environment Heavy Ions (HI) irradiation tests are very good to probe completely the Heavy Ions (HI) irradiation tests are very good to probe completely the
sensitivity of a circuit. With HI, it is possible to vary the LET of the particles sensitivity of a circuit. With HI, it is possible to vary the LET of the particles (hence the energy deposited in the SV), and measure the correspondent cross-(hence the energy deposited in the SV), and measure the correspondent cross-sectionsection
A model of the environment is then necessary to estimate the error rateA model of the environment is then necessary to estimate the error rate
LET= 1 MeVcmLET= 1 MeVcm22/mg/mg
SVSV
Example Example SV: Cube SV: Cube with 1um with 1um sidessides
The path of this particle in the SV is The path of this particle in the SV is 1um. Since the density of Si is 1um. Since the density of Si is 2.32g/cm2.32g/cm33, the energy deposited in , the energy deposited in the SV is about 232keV.the SV is about 232keV.If the LET is changed, by changing If the LET is changed, by changing the ion, to 5, then the deposited the ion, to 5, then the deposited energy exceeds 1MeV.energy exceeds 1MeV.It is possible to chart the measured It is possible to chart the measured cross-section for different LET of the cross-section for different LET of the ions, as shown in the figure to the ions, as shown in the figure to the right.right.
0 20 40 60 80 100 120
Particle LET (Mev cm2/mg) or proton energy (MeV)
cros
s se
ctio
n (
cm2 )
Saturation cross -section
Threshold LET
0 20 40 60 80 100 120
Particle LET (Mev cm2/mg) or proton energy (MeV)
cros
s se
ctio
n (
cm2 )
0 20 40 60 80 100 120
Particle LET (Mev cm2/mg)
cros
s se
ctio
n (
cm2 )
Saturation cross -section
Threshold LET
EIROforum 09 Federico Faccio - CERN 3535
Radiation effects in devices and technologiesRadiation effects in devices and technologies
General viewGeneral view Total Ionizing Dose (TID)Total Ionizing Dose (TID) Displacement damageDisplacement damage Single Event EffectsSingle Event Effects
SEU, SETSEU, SET Destructive eventsDestructive events
OutlineOutline
EIROforum 09 Federico Faccio - CERN 3636
Destructive SEEs (Hard errors)Destructive SEEs (Hard errors) SEBOSEBO => Single Event Burnout=> Single Event Burnout
occurring in power MOSFET, BJToccurring in power MOSFET, BJT(IGBT) and power diodes(IGBT) and power diodes
SEGRSEGR => Single Event Gate Rupture=> Single Event Gate Ruptureoccurring in power MOSFEToccurring in power MOSFET
SELSEL => Single Event Latchup=> Single Event Latchupoccurring in CMOS ICsoccurring in CMOS ICs
They can be triggered by the nuclear interaction They can be triggered by the nuclear interaction of charged hadrons and neutronsof charged hadrons and neutrons
EIROforum 09 Federico Faccio - CERN 3737
Single Event Latchup (SEL)Single Event Latchup (SEL)
VDD
VSS
R1R2
R3R4
R5R6
A.H. Johnston et al., IEEE TNS, Apr. 1996A.H. Johnston et al., IEEE TNS, Apr. 1996
Electrical latchup might be initiated by electrical transients on Electrical latchup might be initiated by electrical transients on input/output lines, elevated T or improper sequencing of power supply input/output lines, elevated T or improper sequencing of power supply biases. These modes are normally addressed by the manufacturer.biases. These modes are normally addressed by the manufacturer.
Latchup can be initiated by ionizing particles (SEL) in any place of the Latchup can be initiated by ionizing particles (SEL) in any place of the circuit (not only IOs)circuit (not only IOs)
n well
p substrate
VDD contact
p +
R1
R2
R3
R4
R5
R6
VDD source
VSS source
VSS contact
p +n +n +
EIROforum 09 Federico Faccio - CERN 3838
SEL: experimentsSEL: experiments
Experiments aim at measuring the cross-section. To avoid destruction Experiments aim at measuring the cross-section. To avoid destruction after the first occurrence, power (both core and I/Os) has to be shut off after the first occurrence, power (both core and I/Os) has to be shut off promptly upon detection of the SELpromptly upon detection of the SEL
SEL sensitivity is enhanced by temperature, hence the test should be SEL sensitivity is enhanced by temperature, hence the test should be done at the maximum foreseen Tdone at the maximum foreseen T
Though in general modern technologies should be less sensitive to Though in general modern technologies should be less sensitive to SEL, there are exceptions!SEL, there are exceptions!
SEL can be induced by high energy protons and neutronsSEL can be induced by high energy protons and neutrons This is not very frequent, but in literature one can find at least 15-20 This is not very frequent, but in literature one can find at least 15-20
devices for which SEL was experimentally induced by proton or neutron devices for which SEL was experimentally induced by proton or neutron irradiationirradiation
When looking at devices for which Heavy Ion data exist in literature, a rule When looking at devices for which Heavy Ion data exist in literature, a rule of a thumb is: if they do not latch below an LET of 15 MeVcmof a thumb is: if they do not latch below an LET of 15 MeVcm22mgmg-1-1, they will , they will not latch in a proton-neutron environment. In fact, typically they need to not latch in a proton-neutron environment. In fact, typically they need to have an SEL threshold around 4 MeVcmhave an SEL threshold around 4 MeVcm22mgmg-1-1 to be sensitive (but take this to be sensitive (but take this figure with precaution, since it is base on little statistics available…)figure with precaution, since it is base on little statistics available…)
If a component is suspected to be sensitive, use high energy protons for If a component is suspected to be sensitive, use high energy protons for the test (the SEL cross-section can be even 15 times larger for tests at the test (the SEL cross-section can be even 15 times larger for tests at 200MeV than for tests with 50MeV protons). Also, use a large fluence of 200MeV than for tests with 50MeV protons). Also, use a large fluence of particles for the test – at least 5x10particles for the test – at least 5x101010 cm cm-2-2 – and to enhance SEL probability – and to enhance SEL probability increase the T during the testincrease the T during the test
EIROforum 09 Federico Faccio - CERN 3939
SEBO (SEB)SEBO (SEB)
Double-diffused MOS (DMOS) power transistor and power Double-diffused MOS (DMOS) power transistor and power BJT transistors are vulnerableBJT transistors are vulnerable
J.H.Johnson & K.F.Galloway, IEEE NSREC short course, 1996
Power DMOSPower DMOS Power BJTPower BJT
EIROforum 09 Federico Faccio - CERN 4040
SEBO (SEB)SEBO (SEB)Mechanism: passage of the ion in the OFF state, generating a Mechanism: passage of the ion in the OFF state, generating a transient current. A regenerative feedback occurs until transient current. A regenerative feedback occurs until second breakdown sets in and permanently destroys the second breakdown sets in and permanently destroys the device (short source-drain or emitter-collector).device (short source-drain or emitter-collector).
Important mechanism in the regenerative feedback: Important mechanism in the regenerative feedback: avalanche-generated hole current in the collector region of avalanche-generated hole current in the collector region of the parasitic (or main) bipolar transistor.the parasitic (or main) bipolar transistor.
J.H.Johnson & K.F.Galloway, IEEE NSREC short course, 1996
EIROforum 09 Federico Faccio - CERN 4141
SEB Example: DC-DC converter (1)SEB Example: DC-DC converter (1)
Power MOSFETs used in candidate DC-DC converter for LHC were Power MOSFETs used in candidate DC-DC converter for LHC were mounted in test cards (below, left) and irradiated a different Vds with mounted in test cards (below, left) and irradiated a different Vds with
60MeV protons. Burnout started from a Vds of about 350V.60MeV protons. Burnout started from a Vds of about 350V.
Vs+
To Counter
250 300 350 400 450 50010
-12
10-11
10-10
10-9
10-8
10-7
Vds (Volts)
Cro
ss
-se
cti
on
(c
m2
)
Q1
Q2
EIROforum 09 Federico Faccio - CERN 4242
SEB Example: DC-DC converter (2)SEB Example: DC-DC converter (2)
From previous curve and with analysis of the converter, it is possible to From previous curve and with analysis of the converter, it is possible to select a working condition where Vds of the MOSFET never exceeds select a working condition where Vds of the MOSFET never exceeds 300V (this technique is called “derating” and is often used)300V (this technique is called “derating” and is often used)
0 5 10 15 20200
220
240
260
280
300
320
340
360
380V300B12C250AL
Output Current (A)
Dra
in-S
ourc
e Vo
ltage
(V)
Vin = 300VVout = 12V
Vin = 200VVout = 12V
Vin = 200VVout = 7.7V
Safe areaSafe area
EIROforum 09 Federico Faccio - CERN 4343
SEGR in power MOSFETsSEGR in power MOSFETs
SEGR is caused by heavy-ion-induced localized dielectric SEGR is caused by heavy-ion-induced localized dielectric breakdown of the gate oxide. SEGR test is destructive!breakdown of the gate oxide. SEGR test is destructive!
J.H.Johnson & K.F.Galloway, IEEE NSREC short course, 1996
EIROforum 09 Federico Faccio - CERN 4444
Radiation effects in devices and technologiesRadiation effects in devices and technologies
Summary TableSummary TableDevice TID Displacement SEEs
Low voltage CMOS Yes1 No SEUs in logic and memoriesSETs relevant if fast logic (1GHz)SEL possible2
Low voltage Bipolar Yes, with ELDR possible
Yes3 SEL extremely rare – if at allSETs
Low voltage BiCMOS Yes Yes Combination of CMOS and Bipolar
Power MOSFETs Yes Yes at very large fluence (>10f)
SEBSEGR
Power BJTs Yes Yes SEB
Optocouplers Yes Yes SETs
Optical receivers Yes Yes (tech dependent) “SEUs”
1The threshold for sensitivity varies with technology generation and function. Typically failures are observed from a minimum of 1-3krd, and sensitivity decreases with technology node (130nm less sensitive than 250nm for instance)2Sensitivity typically decreases with technology node. When Vdd goes below about 0.8-1V, then SEL should not appear any more3Sensitivity depends on doping and thickness of the base, hence decreasing in modern fast processes
EIROforum 09 Federico Faccio - CERN 4545
Particles and damagesParticles and damagesRadiation TID Displacement (NIEL) SEE
X-rays60Co
Expressed in SiO2
Almost identical in Si or SiO2
No No
p Equivalences in Si$
@60MeV 1011p/cm2=13.8krd@100MeV 1011p/cm2=9.4krd@150MeV 1011p/cm2=7.0krd@200MeV 1011p/cm2=5.8krd@250MeV 1011p/cm2=5.1krd@300MeV 1011p/cm2=4.6krd@23GeV 1011p/cm2=3.2krd
Equivalences in Si$,*
@53MeV 1 p/cm2 = 1.25 n/cm2
@98MeV 1 p/cm2 = 0.92 n/cm2
@154MeV 1 p/cm2 = 0.74 n/cm2
@197MeV 1 p/cm2 = 0.66 n/cm2
@244MeV 1 p/cm2 = 0.63 n/cm2
@294MeV 1 p/cm2 = 0.61 n/cm2
@23GeV 1 p/cm2 = 0.50 n/cm2
Only via nuclear interaction. Max LET of recoil in Silicon = 15MeVcm2mg-1
n Negligible Equivalences in Si$,*
@1MeV 1 n/cm2 = 0.81 n/cm2
@2MeV 1 n/cm2 = 0.74 n/cm2
@14MeV 1 n/cm2 = 1.50 n/cm2
As for protons, actually above 20MeV p and n can roughly be considered to have the same effect for SEEs
Heavy Ions Negligible for practical purposes (example: 106 HI with LET=50MeVcm2mg-1 deposit about 800 rd)
Negligible Yes
$ Energy here is only kinetic (for total particle energy, add the rest energy mc2)*The equivalence is referred to “equivalent 1Mev neutrons”, where the NIEL of “1MeV neutrons” is DEFINED to be 95 MeVmb. This explains why for 1MeV neutrons the equivalence is different than 1
EIROforum 09 Federico Faccio - CERN 4646
To study further…To study further…
General material on radiation effects:General material on radiation effects: The best source is the “archive of Radiation Effects Short Course Notebooks, 1980-The best source is the “archive of Radiation Effects Short Course Notebooks, 1980-
2006” collecting the courses given at the IEEE NSREC conference (CD sold by IEEE)2006” collecting the courses given at the IEEE NSREC conference (CD sold by IEEE) ““Classic” books on the subjectClassic” books on the subject
• ““Ionizing radiation effects in MOS devices and circuits”, edited by T.Ma and P.Dressendorfer, Ionizing radiation effects in MOS devices and circuits”, edited by T.Ma and P.Dressendorfer, published by Wiley (2001), ISBN 978-0471848936published by Wiley (2001), ISBN 978-0471848936
• ““Handbook of radiation effects”, by A.Holmes-Siedle and L.Adams, published by Oxford Handbook of radiation effects”, by A.Holmes-Siedle and L.Adams, published by Oxford University Press (2002), ISBN 978-0198507338 University Press (2002), ISBN 978-0198507338
Recent Books with good overview of all effects:Recent Books with good overview of all effects:• ““Radiation effects on Embedded Systems”, edited by R.Velazco, P.Fouillat, R.Reis, published Radiation effects on Embedded Systems”, edited by R.Velazco, P.Fouillat, R.Reis, published
by Springer (2007), ISBN 978-1-4020-5645-1by Springer (2007), ISBN 978-1-4020-5645-1• ““Radiation effects and soft errors in integrated circuits and electronic devices”, edited by Radiation effects and soft errors in integrated circuits and electronic devices”, edited by
R.Schrimpf and D.Fleetwood, published by World Scientific (2004), ISBN 981-238-940-7R.Schrimpf and D.Fleetwood, published by World Scientific (2004), ISBN 981-238-940-7 Best papers from the Nuclear and Space Radiation Effects Conference (NSREC) are Best papers from the Nuclear and Space Radiation Effects Conference (NSREC) are
published yearly in the IEEE TNS in the december special Issuepublished yearly in the IEEE TNS in the december special Issue Specialized conferences:Specialized conferences:
NSREC in the US, yearly in JulyNSREC in the US, yearly in July RADECs in Europe, conference (1 week) or workshop (2-3 days) every year in RADECs in Europe, conference (1 week) or workshop (2-3 days) every year in
SeptemberSeptember