04 01-03 cr 201203 - elepon · elepon e.c.a.p. corporation 【4 metering pumps ･･･...

ELEPON E.C.A.P. Corporation 【4 METERING PUMPS ･･･ 4-1.CR-N,4-2.CRM,4-3.OPTIONS】Ver.201203 1

4.Metering Pumps

ELEPON FEEDER CR-N and CRM Series are designed as the direct-motion diaphragm injection pumps as safe and multipurpose pumps and also low-cast pumps. These pumps are used as the injection pump for water treatment chemicals or the chemical injection pumps for many other kinds of fields.

CONSTRUCTIONS

● CR-N Series、CRA-N Series: servo control model

CR-2N CR-3-2N CR-5N CR-2DN

CR-6DN CR-40DN CRA-N Series CRK-N Series

CRP-N Series (Special specification)

Nanoparticle correspondence ・CRK-N Series：A motor with general-purpose base is adopted. ・CRP-N Series：CRP-N Series pump is Permanent Magnet Synchronous Motor Model.

※Special inverter for the motor is needed to drive this pump. ※As for the motor, indoor specifications are standards.

Specifically, please make an inquiry.

● CRM Series: the discharge amount is under 1,400mℓ/min.

CRM-02 CRM-12 CRM-70


FEATURES ・Wetted parts of the pump resist fluids of wide range. ・Standard types ( up to 300 mPa･s.) and high viscosity types ( up to 2,000 mPa･s ). ・The compact design features less parts, and maintenance and inspection is easy. Hose connections and

flange connections are also possible. ・The small capacity pump (Models CR-1N to CR-3N) uses a planetary gear two-stage reduction

mechanism, and medium- and large-capacity pumps of 200W or more use a worm gear reduction mechanism to provide long-term worry-free continuous operation.

・The discharge volume can be manually adjusted regardless of whether the pump is running or stopped.

・Adjustment of the quantity of discharge by the manual operation is possible any time when the pump is in operation or is not in operation.

APPLICATIONS ・Corrosive chemical solutions, acids and alkalis ・Photograph developing solutions, fixers, bleaching solutions and inks ・Sea water, Salt water and pure water ・Soy sauce, vinegar, brewery, and fruit juice ・Plating solutions, surface treating apparatus, and filtration system ・Medical apparatus, physicochemical apparatus, and thermostatic baths ・Drugs, chemicals, and cosmetics ・Etching apparatus for electronic parts, and photochemical processes ・Dyeing equipment and waste liquid treating units ・Alkaline batteries, and storage batteries ・Refrigerators, cold counters, and coolers ・Vending machines for beverages, and ice machines Laboratories, test rooms and test plants Processes ・For hot water circulation ・Other apparatus and equipment

Pump Head: PVC ACRYLIC SUS PVDF

Discharge Quantity Control Dial

Double reduction mechanism with planetary gears


4-1.Metering Pumps CR-N Series

MODEL CODE

Standard A 6 A Servo control model B 10/13

①MODEL

K Motor with general-purpose base is adopted

C 12

P Permanent Magnet Synchronous Motor Model

D 15

Single E 20 D Double G 25

J 40

②Pump Head Type

T Triple head type （Only as for 100V of CR-1N - 3N） K 50

P PVC L 65 Q PVC（High viscosity）

⑦Suction / Discharge Size

(mm)

N 8 A Acrylics 1 100V

B Acrylics （High viscosity） 2 200V

D PVDF 3 220V 4 SUS-304 4 380V 6 SUS-316 5 400V

4L SUS-304L 6 415V

③Pump Head Materials

6L SUS-316L 7 440V F FKM

⑧Motor Voltage

Z Others E EPDM S 1-phase P PTFE T I 3-phase（Indoor）

④O-ring Materials

Z Others T O 3-phase（Outdoor）

C Ceramic E I Increased safety explosion-proof type motors（Indoor）

P PTFE E OIncreased safety explosion-proof type motors（Outdoor）

S SUS-316 D IFlame-proof and explosion-proof type motors（Indoor）

⑤ Ball Valves Materials

H Hastelloy C D OFlame-proof and explosion-proof type motors（Outdoor）

F Flange I I Inverter（Indoor） H Hose I O Inverter（Outdoor） N Threads connection

⑨ Motor

Z Others U Union A ANSI (150#)

⑥ Suction / Discharge Materials

Z Others

Pump Head MODEL

Type Materials O-ring

BallValve

Suction Discharge Motor

① ② ③ ④ ⑤ ⑥ ⑦ ⑥ ⑦ ⑧ ⑨

CR □ － 1□N － P F C H A / H A － 2 TI


STANDARD MATERIALS FOR WETTING PARTS

PVC Acrylics Stainless Steel (SUS-304) PVDF

Diaphragm Lock Nut PVC PVC Stainless Steel (SUS-304) PVDF

Suction and Discharge Connector PVC PVC Stainless Steel (SUS-304) PVDF

Diaphragm PTFE PTFE PTFE PTFE

Ball Valve Ceramics Ceramics Stainless Steel (SUS-316) PTFE

O-ring FKM FKM PTFE PTFE

● SUS-304 is the standard. If you require SUS-316, please specify.

STANDARD ACCESSORIES (Material: PVC)

MODEL Braid Hose Strainer Reducer Oil Injection Port

CR-1N 、CR-1-2N φ6mm×φ11mm×4m 1 － 1

CR-2N φ6mm×φ11mm×4m 1 － 1

CR-2-2N － 1 －－

CR-3N 、CR-3-2N － 1 －－

CR-4DN － 2 0.3 ℓ －

CR-4N （5DN）－ 1 （2） 0.3 ℓ －

CR-5N （6DN）－ 1 （2） 0.3 ℓ －

CR-6N （10DN）－ 1 （2） 0.3 ℓ －

CR-10aN （20DN）－－ 0.7 ℓ （1 ℓ ）－

CR-20aN （40DN）－－ 0.7 ℓ （1 ℓ ）－

CR-30aN （60DN）－－ 0.7 ℓ （1 ℓ ）－

SPECIFICATIONS

CR-N Series

●SINGLE HEAD TYPE

Capacity (mℓ/min)

Connection Size (mm)

MODEL

50Hz 60Hz

MaximumDischargePressure

(Mpa)

Motor Rating Output PVC

ACRYLICS SUS PVDF

Weight(PVC)(kg)

SuctionHead (m)

CR-1N 6～ 60 7～ 75

CR-1-2N 14～ 140 17～ 170 1.3

CR-2N 27～ 270 33～ 330

φ6×φ11 Hose

20.5 -1.5

CR-2-2N 68～ 680 82～ 820 1.0

1-phase 100V3-phase 200V

0.1kW OutdoorJIS 10K 13A

Flange

R 3/8φ8×φ10

PTFE Hose

21.5 -1.5

Pump Head Material PARTS


CR-3N 100～1,000 120～1,200

CR-3-2N 160～1,600

（150～ 1,500）

190～1,900 （180～ 1,800）

0.7 1-phase 100V3-phase 200V

0.1kW Outdoor

JIS 10K 15AFlange

R 1/2JIS 10K

15A Flange

22 -1.5

CR-4N 210～2,100

（205～ 2,050）

250～2,500 （245～ 2,450）

3-phase 200V0.2kW

29 -1.5

CR-5N 260～2,600

（250～ 2,500）

310～3,100 （300～ 3,000）

0.5 JIS 10K 20A

Flange R 3/4

JIS 10K 20A

Flange 32 -1.5

CR-6N 500～5,000

（480～ 4,800）

600～6,000 （575～ 5,750）

0.3

3-phase 200V0.4kW

JIS 10K 25AFlange

R 1 JIS 10K

25A Flange

38.5 -1.5

CR-10aN 1,000～

10,500 1,200～

12,500 0.5 JIS 10K 40A Flange 80 -1.0

CR-20aN 2,000～

20,500 2,400～

24,400

3-phase 200V0.75kW Outdoor

JIS 10K 50A Flange 90 -1.0

CR-30aN 3,000～

30,000 3,600～

36,000

0.3 3-phase 200V

1.5kW OutdoorJIS 10K 65A Flange 100 -1.0

●DOUBLE HEAD TYPE (the flow rates below are dual)Capacity （mℓ/min) Connection Size (mm)

MODEL 50Hz 60Hz

MaximumDischargePressure(MPa)


ACRYLICSSUS PVDF

Weight(PVC)( kg )

SuctionHead( m )

CR-1DN 12～ 120 15～ 150

CR-1D-2N 28～ 280 34～ 340 1.3 22.5 -1.5

CR-2DN 54～ 540 66～ 660

φ6×φ11Hose

23.5 -1.5

CR-2D-2N 136～ 1,360 164～1,640 1.0 JIS 10K

13A Flange

R 3/8 φ8×φ10

PTFE Hose

24.5 -1.5

CR-3DN 200～ 2,000 240～2,400 0.7

1-phase100V3-phase 200V

0.1kW Outdoor

JIS 10K 15A

Flange R 1/2

JIS 10K 15A

Flange 25.5 -1.5

CR-4DN 210～ 2,100

（205～ 2,050）

250～2,500 （245～2,450）

32 -1.5

CR-5DN 420～ 4,200

（410～ 4,100）

500～5,000 （490～4,900）

3-phase 200V0.2kW

33 -1.5

CR-6DN 520～ 5,200

（500～ 5,000）

620～6,200 （600～6,000）

0.5 JIS 10K

20A Flange

R 3/4 JIS 10K

20A Flange

37 -1.5

CR-10DN

1,000～

10,000 （960～ 9,600）

1,200～12,000 （1,150～

11,500） 0.3

3-phase 200V0.4kW

JIS 10K 25A

Flange R 1

JIS 10K 25A

Flange 42.5 -1.5

CR-20DN 2,100～

21,000 2,500～

25,000 0.5

3-phase 200V1.5kW

Outdoor JIS 10K 40A Flange 130 -1


CR-40DN 4,100～

41,000 5,000～

50,000 JIS 10K 50A Flange 145 -1

CR-60DN 5,800～

58,000 7,000～

70,000

0.3 3-phase 200V

1.5kW Outdoor

JIS 10K 65A Flange 150 -1

*Note: We also have triple-head types, CR-1TN, CR-2TN and CR-3TN, which discharge three times as much

as shingle-head types. We have standard types (up to 300mPa･s) and high viscosity types (up to 2,000mPa･s). Please specify

the type you need when you place your order. Please inquire to us in case of using the slurry. Available liguid temperature range is 0～50℃ (PVC) or 0～80℃ (stainless Steel, PVDF). Standard specifications of connection pipe size etc. are described at table above. We can change them according to your needs. The discharge quantities in the ( ) are data of SUS pump head.

CRA-N Series

APPLICATIONS Combination use with conductivity meter, pH meter, ORP meter, residual chlorine meter, liquid

level gage and other control device.FEATURES Full-automatic operation Continuous control Wide range of application possible by adding controller A certain response to the input signal brings the stable driving. Stable quantity of discharge is ensured by use of Elepon’s reliable CR-N type feeder. You can control

the discharge (0% to 100%) manually during operation or stops. With CR-N series you can controlthe quantity of flow automatically using electric signals from automatic controllers.

※ example of control

※ example of combination

E.E. Positioner MODEL:E-661 ･･･ with proportional action


Capacity （mℓ/min) Servo Control Motor Spec.

MODEL 50Hz 60Hz


(MPa) Model Motor

100V

Control Speed

0～100% 50Hz/60Hz

E.E. Positioner

Weight(PVC) （kg）

CRA-1N 0～60 0～75 1.3 24

CRA-1-2N 0～140 0～170 1.3 24

CRA-2N 0～270 0～330 1.0 24.5

CRA-2-2N 0～680 0～820 1.0 25

CRA-3N 0～1,000 0～1,200 0.7 26

CRA-3-2N 0～1,600

（0～1,500) 0～1,900

（0～1,800) 0.7

CM-102P 6W 13.3/11 sec.

26

CRA-4N 0～2,100

（0～2,050) 0～2,500

（0～2,450) 0.5 CM-102-1P 6W 22.8/19 sec. 34

CRA-5N 0～2,600

（0～2,500) 0～3,100

（0～3,000) 0.5 37

CRA-6N 0～5,000

（0～4,800) 0～6,000

（0～5,750) 0.3

CM-102-2P 6W 27.6/23 sec. 43.5

CRA-10aN 0～10,500 0～12,500 0.5 CM-2410P 60W 17 /14 sec. 95

CRA-20aN 0～20,500 0～24,400 0.3 CM-2420P 60W 23 /19 sec. 105

CRA-30aN 0～30,000 0～36,000 0.3 CM-2430P 60W 24 /20 sec.

MODEL E-660,E-661Input signal

4～20mA DC

120

*Note: The discharge quantities in the ( ) are data of SUS pump head.

CRK-N Series (Various kinds of motors can be installed.)

FEATURES

Various kinds of motors can be installed. ・Inverter motors ・Increased safty explosion-proof type motors ・Flame-proof and explosion-proof type motors

Please inquire an order by a motor of the special specification.

SPECIAL SPECIFICATION: CRP-N Series (Permanent Magnet Synchronous Motor Model)

FEATURES CRP-N series is using a PM motor.

Compared with the CR-N Series・・・・ELECTRICITY SAVING

・DOWNSIZED

・LIGHT-WEIGHTED

・DISCHARGING PERFORMANCE IMPROVED

Please inquire for more information.

Usage example

CR-N series CRP-N series


SPECIAL SPECIFICATION: Nanoparticle correspondence

FEATURES In order to transport the dispersed nanoparticle,

it is the pump which reduced the dead space inside a pump to the limit.

※It proposes the design development of the pump at a low price according to needs, and consult, please.


PERFORMANCE CURVE

Dial scale Dial scale Dial scale Dial scale

Dial scale

Capacity mℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacity mℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacitymℓ/min

Dial scale Dial scale Dial scale

Dial scale Dial scale Dial scale Dial scale

Dial scale

Capacity mℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacity mℓ/min

Capacitymℓ/min

Capacitymℓ/min

Capacitymℓ/min


Capacity mℓ/min

Capacitymℓ/min

Capacitymℓ/min



4-2. Matering Pumps CRM Series 4-

MODEL CODE

Suction Discharge Motor PumpHead O-ring Ball

Valve Materials Size Materials Size Voltage PhaseMODEL

① ② ③ ④ ⑤ ④ ⑤ ⑥ ⑦

CRM－02 P F C H A － H A － 2 T I

P PVC A 6 Q PVC（High viscosity） B 10/13 4 SUS-304 C 12 6 SUS-316 D 15

4L SUS-304L

⑤

Suction / Discharge Size (mm) M 4

①

Pump Head Type

6L SUS-316L 1 100V F FKM 2 200V E EPDM 3 220V P PTFE 4 380V

②

O-ring Materials

Z Others 5 400V C Ceramics 6 415V S SUS-316 7 440V

③

Ball Valve Materials H Hastelloy C

⑥

Motor Voltage

Z Others F Flange S 1-phase H Hose TO 3-phase（Outdoor）

N Threads connection EIIncreased safety explosion-proof type motors（indoor） 3-phase 200V only

U Union

⑦

Motor Phase

Z Others A ANSI(150#)

④

Suction / Discharge

Materials

Z Others

STANDARD MATERIALS FOR WETTING PARTS

PVC SUS

Suction and Discharge Connectors PVC SUS-304

Diaphragm PTFE PTFE

Ball Valve Ceramic SUS-316

O－ring FKM PTFE

● SUS-304 is the standard. If you require SUS-316, please specify.

Pump Head Materials

PARTS


STANDARD ACCESSORIES (Material: PVC)

SPECIFICATIONS

Capacity （mℓ/min) Connection Size

MODEL 50Hz 60Hz


(MPa)


ACRYLICS SUS

Weight(PVC) ( kg )

SuctionHead ( m )

CRM-02 2 ～20 2.4 ～24 1 -1.0

CRM-04 4 ～40 4.8 ～48 1 6.5

-1.0

CRM-12 12 ～120 14 ～140 1 -1.0

CRM-24 24 ～240 28 ～280 0.7

25W

φ4×φ9 Hose

JIS 10K 13A Flange

R 3/8

7.5 -1.0

CRM-70 64 ～640 76 ～760 -1.0

CRM-140 110～1,100

140～1,400

0.5

1-phase 100V1-phase 200V3-phase 200V

40W

φ15×φ22 Hose

JIS 10K 15A Flange

R 1/2 12 -1.0

MODEL Braid Hose Strainer Injection Port

CRM-02 φ4mm×φ9mm×3m 1 1

CRM-04 φ4mm×φ9mm×3m 1 1

CRM-12 φ6mm×φ11mm×4m 1 －

CRM-24 φ6mm×φ11mm×4m 1 －

CRM-70、140 － 1 －


PERFORMANCE CURVE



Capacity mℓ/min

Capacity mℓ/min

Capacity mℓ/min

Capacity mℓ/min

Capacity mℓ/min

Capacity mℓ/min


4-3. Option (FOR CR-N, CRM Series)

COUPLING

TYPE : A TYPE : B TYPE : C TYPE : D

Flange×Hose Flange×Hose Screw×Hose Screw×Hose

●Flange×Hose size:mm Connection Size (mm) MODEL Flange Hose

Connection Type

JP-13F-4H φ4× φ9 JP-13F-6H φ6×φ11

A

JP-13F-12H JIS 10K 13A

φ12×φ18 B JP-15F-4H φ4× φ9 JP-15F-6H φ6×φ11

A

JP-15F-12H φ12×φ18 JP-15F-15H

JIS 10K 15A

φ15×φ22 JP-20F-19H JIS 10K 20A φ19×φ26 JP-25F-25H JIS 10K 25A φ25×φ33 JP-40F-38H JIS 10K 40A φ38×φ48 JP-50F-50H JIS 10K 50A φ50×φ62 JP-65F-63H JIS 10K 65A φ63×φ80

B

● Materials: PVC●Screw×Hose

MODEL Connection Size Hose (mm)

Connection Type

JP-1/2-4H φ4× φ9 JP-1/2-6H φ6×φ11

C

JP-1/2-12H φ12×φ18 JP-1/2-15H φ15×φ22

D

● Materials: PVC

MIXER AIR CHAMBER

AIR CHAMBER

PRESSURE GAUGE

PRESSURE GAUGE

PRESSURE GAUGE

SAFETY VALVE

BACK PRESSURE

VALVE BACK

PRESSUREVALVE

SAFETY VALVE

MIXER

STRAINER STRAINER

FLOW CHECKER

PUMP STAND


BACK PRESSURE VALVE

BP-4/6HK BP-6HK BP-15FV

MODEL Material Connecting Pipe

Aperture (mm)

MaximumAmount ofDischarge（L/min）

Range of set Pressure

（Standard Setting Pressure）

(MPa)

Weight(kg)

Metering Pumps

BP-4/6HK PVC φ4×φ9 Hose×R1/2 φ6×φ11 Hose×R1/2

0.3 fixed at 0.15 0.13 CRM-02、04、12、24

BP-06HK PVC φ6×φ11 Hose 0.5 fixed at 0.15 0.5 CR-1N、1-2N、2N

BP-13FK fixed at 0.15 0.6

BP-13FV PVC JIS10K13A Flange 1.0

0.1～0.3（0.15） 1

CRM-02、04、12、24 CR-1N、1-2N、2N、2-2N

BP-15FK fixed at 0.15 0.7 CRM-70、140

BP-15FV PVC JIS10K15A Flange 2.0

0.1～0.3（0.15） 1 CR-3N、3-2N

BP-20FV PVC JIS10K20A Flange 6.0 0.1～0.3（0.1） 1 CR-4N、5N、4DN、5DN、6DN

BP-25FV PVC JIS10K25A Flange 15.0 0.1～0.3（0.1） 2 CR-6N、10DN

BP-40FV PVC JIS10K40A Flange 40.0 0.1～0.3（0.1） 4 CR-10aN

BP-50FV PVC JIS10K50A Flange 40.0 0.1～0.3（0.1） 4.5 CR-20aN、30aN

BS-10NV 3/8 Screwed 1.0 2

BS-10FV SUS

JIS10K10A Flange 3.0 0.1～0.3（0.15）

3

CRM-02、04、12、24 CR-1N、1-2N、2N、2-2N


BS-15FV SUS

JIS10K15A Flange 3.0 0.1～0.3（0.15）

3

CRM-70、140 CR-3N、3-2N


BS-20FV SUS

JIS10K20A Flange 4.0 0.1～0.3（0.1）

4 CR-4N、5N、4DN、5DN、6DN

BS-25NV 1 Screwed 15.0 4

BS-25FV SUS

JIS10K25A Flange 7.0 0.1～0.3（0.1）

7 CR-6N、10DN

BS-40NV 1 1/2 Screwed 40.0 12

BS-40FV SUS

JIS10K40A Flange 15.0 0.1～0.3（0.1）

15 CR-10aN、20aN、30aN

BF-13FV PVDF JIS10K13A Flange 1.0 0.1～0.3（0.15） 1 CR-1N、1-2N、2N、2-2N

BF-15FV PVDF JIS10K15A Flange 2.0 0.1～0.3（0.15） 1.5 CR-3N、3-2N

BF-20FV PVDF JIS10K20A Flange 6.0 0.1～0.3（0.1） 1.5 CR-4N、5N、4DN、5DN、6DN

BF-25FV PVDF JIS10K25A Flange 15.0 0.1～0.3（0.1） 2 CR-6N、10DN

BF-40FV PVDF JIS10K40A Flange 40.0 0.1～0.3（0.1） 4 CR-10aN、20aN、30aN


SAFETY VALVE When the abnormal high pressure which is caused by closed valve or by the blockade of the foreign substance is inside of the discharge pipe, the safty valve will be opened automatically so that the damage of a pump or piping may be prevented.

MODEL Material

Connecting Pipe Aperture

(mm)

MaximumAmount ofDischarge（L/min）


（Standard setting Pressure）

(MPa)

Weight(kg)

Metering Pumps

RP-13FV JIS 10K 13A Flange

RP-15FV PVC

JIS 10K 15A Flange

6 0.2～0.5 （0.3） 1 CRM-02 、04 、12 、24、70 、140 CR-1N 、1-2N 、2N 、2-2N、3N 、

3-2N

RP-20FV PVC JIS 10K 20A Flange 25 0.2～0.5 （0.3） 1.5 CR-4N 、5N、4DN 、5DN 、6DN

RP-25FV PVC JIS 10K 25A Flange 0.2～0.5 （0.3） 1.5 CR-6N 、 10DN 、 10aN 、 20aN 、

30aN

RS-10NV Rc 3/8 Srewed

40

2

RS-10FV JIS 10K 10A Flange

RS-15FV

SUS

JIS 10K 15A Flange 6

0.2～0.5 （0.3） 4

CRM-02 、04 、12 、24 CRM-70 、140 CR-1N 、1-2N 、2N 、2-2N、3N 、

3-2N

RS-20NV Rc 3/4 Srewed

RS-20FV SUS

JIS 10K 20A Flange 25 0.2～0.5 （0.3） 4

CR-4N 、5NCR-4DN 、5DN 、6DN

RS-25NV Rc 1 Srewed 4

RS-25FV SUS

JIS 10K 25A Flange 40 0.2～0.5 （0.3）

7

CR-6N 、10DN、10aN 、20aN 、

30aN

RF-13FV JIS 10K 13A Flange

RF-15FV PVDF

JIS 10K 15A Flange 6 0.2～0.5 （0.3） 1

CR-1N 、1-2N 、2N 、2-2N、3N 、

3-2N

RF-20FV PVDF JIS 10K 20A Flange 25 0.2～0.5 （0.3） 1.5 CR-4N 、5N、4DN 、5DN 、6DN

RF-25FV PVDF JIS 10K 25A Flange 40 0.2～0.5 （0.3） 2 CR-6N 、10DN、10aN 、20aN 、

30aN


AIR CHAMBER Pulsation is a detriment of reciprocating pumps. Please install an air chamber when pulsation must be prevented.

MODEL Material

Connection Pipe Size

(mm)


（Standard setting Pressure）

(MPa)

Volume (L)

Adaptable Pumps

APN-X10-13F PVC JIS10K13A Flange 0.5 0.9 CRM-02、04、12、24 CR-1N、1-2N、2N、2-2N

APN-X15-15F PVC JIS10K15A Flange 0.5 1.4 CRM-70、140 CR-3N、3-2N

APN-Y30-20F PVC JIS10K20A Flange 0.5 2.5 CR-4N、5N、4DN、5DN、6DN

APN-Y40-25F PVC JIS10K25A Flange 0.5 3.7 CR-6N、10DN

APN-Z100-40F PVC JIS10K40A Flange 0.5 10 CR-10aN



AP-150-40F(with base） PVC JIS10K40A Flange 0.5 8 CR-10aN

AP-200-50F(with base） PVC JIS10K50A Flange 0.3 17 CR-20aN

AP-200-65F (with base） PVC JIS10K65A Flange 0.3 17 CR-30aN

AS-50-10N SUS 3/8 screwed 0.5 0.7

AS-50-10F SUS JIS10K10A Flange 0.5 0.7

CRM-02、04、12、24 CR-1N、1-2N、2N、2-2N

AS-80-15N SUS 1/2 screwed 0.5 1.5

AS-80-15F SUS JIS10K15A Flange 0.5 1.5

CRM-70、140 CR-3N、3-2N

AS-100-20N SUS 3/4 screwed 0.5 2.5

AS-100-20F SUS JIS10K20A Flange 0.5 2.5 CR-4N、5N、4DN、5DN、6DN

AS-150-25N SUS 1 screwed 0.5 5.3

AS-150-25F SUS JIS10K25A Flange 0.5 5.3 CR-6N、10DN

AS-150-40F SUS JIS10K40A Flange 0.5 10 CR-10aN



AF-50-13F PVDF JIS10K13A Flange 0.3 0.7 CR-1N、1-2N、2N、2-2N

AF-80-15F PVDF JIS10K15A Flange 0.3 1.5 CR-3N、3-2N

AF-100-20F PVDF JIS10K20A Flange 0.3 2 CR-4N、5N、4DN、5DN、6DN

AF-100-25F PVDF JIS10K25A Flange 0.3 4.9 CR-6N、10DN

ReferenceElepon E.C.A.P. Corporation Osakashinai Bld., 3-2-23, Kitahama, Chuo-ku Osaka-shi, Osaka, 541-0041, Japan

E-mail：[email protected] URL：http://www.elepon.co.jp

04 01-03 cr 201203 - elepon · elepon e.c.a.p. corporation 【4 metering pumps ･･･...

Documents