z1 ballerina vanity unit - reece group · inspired by the grace of a dancer balancing effortlessly...
TRANSCRIPT
To see the complete ISSY range go to www.reece.com.au/bathrooms
Pony Oak Hazelnut Oak
ISSY //Z1 BALLERINA VANITY UNIT
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 2
Inspired by the grace of a dancer balancing effortlessly on pointe, ISSY Z1 Ballerina Vanity Unit brings elegance and lightness to the bathroom. Crafted from solid American Oak, the superb timber grain naturally complements the tapered leg design. Impeccably finished with a bevelled edge, Corian benchtop and choice of En Pointe feet, the vanity can be paired with a matching oval or round mirror for stunning effect.
Designed and Manufactured in Australia
CLEANING RECOMMENDATIONSYour timber frame should be cleaned with a mild, non acidic, non abrasive detergent and soft cloth . Finish by cleaning off detergents with a soft damp cloth and towel dry. Always clean spills and water immediately. Please refrain from hanging wet towel on Ballerina bar, as this may damage the timber.
Damage caused by any improper treatement is not covered by the product warranty. Refer to Warranty Conditions.
SPECIFICATIONSRecommended use Domestic, Commercial & Hotel
Materials Vanity Frame - Solid American Oak
Bench Top - Corian
En Pointe Feet - Electroplated Metal
Timber Colours American Oak, Charcoal Oak, Pony Oak , Hazelnut Oak.
Corian Colours Glacier White, Weathered Aggregate, Oyster, Deep Night Sky
En Pointe Colours Brushed Nickel, Chrome, Gold, Rose Gold, Matt Black, Gunmetal
Fixing Bolted / Screwed to Wall by a Licensed Trades Person
Basin Sold Separately
STANDARD SIZES VU800 VU1000 VU1200Width (mm) 800 1000 1200
Depth (mm) 450 450 450
Height (mm) 760 760 760
CUSTOM SIZES VU700-900 VU901-1100 VU1101-1300Width (mm) 700 - 900 901 - 1100 1101 - 1300
Depth (mm) 400 - 450 400 - 450 400 - 450
Height (mm) 700 - 800 700 - 800 700 - 800
page 1 of 6
ISSY //Z1 BALLERINA VANITIESCOLOUR OPTIONS
AMERICAN OAK
CHARCOAL OAKPONY OAK
HAZELNUT OAK
DEEP NIGHT SKYOYSTER
WEATHERED AGGREGATEGLACIER WHITE
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
GUNMETALGOLD
MATT BLACKROSE GOLD
CHROMEBRUSHED NICKEL
CORIAN OPTIONSTIMBER OPTIONS
BALLERINA EN POINTE OPTIONS
ENPOINTE HEIGHT 25W X 125H
125MM
page 2 of 6
STANDARD SIZES - 450 DEEP
ISSY //Z1 BALLERINA VANITIES
1000W X 450D X 760H
1200W X 450D X 760H
800W X 450D X 760H
page 3 of 6
CUSTOM SIZES - 400-450 DEEP
ISSY //Z1 BALLERINA VANITIES
1101-1300W X 400-450D X 760H
901-1100W X 400-450D X 760H
700-900W X 400-450D X 760H
page 4 of 6
ISSY //Z1 BALLERINA VANITIES
BALLERINA CUTOUTS FOR CORIAN TOP - STANDARD / CUSTOM SIZES
600600
200
200
200
200200
130130
130130
130
500500
400
CUTOUT 1: 800 x 400
CUTOUT 2: 1000 x 400
CUTOUT 3: 1200 x 400
CUTOUT : 800 x 450
CUTOUT : 1000 x 450
CUTOUT 6: 1200 x 450
Radius 50mm
100
100
100
100100
100
125125
125125
800
10001000
1200 1200
200150
150
130
400
800
page 5 of 6
ISSY //Z1 BALLERINA VANITIES
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
• Prior to installation it is important to inspect the Z1 Ballerina Vanity to ensure no damage has occurred in transit. If damage has occurred, or a visible defect exists, DO NOT proceed with installation and advise supplier immediately. No warranty claim for damage will be accepted if the Vanity is installed.
Please Note: Manufacturer will not be liable for the cost of installation or removal of the vanity and the warranty will be voided if damage occurred during or after installation.
• Mark the wall where the vanity is going to be installed. Waste plumbing should align with the centre of unit where the cutout will be located. Unit MUST SIT FLUSH with wall when in contact with the ground.
• Drill through any part of the back panel of the unit to fix to wall ENSURING CONTACT TO STUDS.
• Screw/Bolt unit onto wall
• Place Corian top on unit using silicon to fix in place.
INSTALLATION INSTRUCTIONS
NO Cutout45mmSTANDARD
Recommended for most basins 45mm Hole used for dish vessel basin such as the Alape Circa
Used as a dresser.
page 6 of 6