your trusted partner for device networking & computing · • 4 x 921.6kbps high speed tty...

Your Trusted Partner for Device Networking & Computing

Intelligent IoT GatewayIoT Device PlatformProgrammable Automation ControllerWeb-based Remote I/O

www.artila.com

Artila Electronics Co., Ltd.

www.artila.com

4F., No. 6, Lane 130, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)Tel: +886-2-8667-2340Fax: +886-2-8667-3240Email: [email protected]

All specifications are subject to change without further notice.

All products and company names listed are trademarks or trade names of their respective companies.

50-401502

Artila Electronics is founded by professionals with more than 15 years of experience in Industrial Computing field.

From product design to production quality, Artila Electronics strives for delivering top notch services to industrial automation market.

Product Introduction

01

Who We Are

ARM-based automation controller supporting industrial A/I and DIO released.

Web-based device management software and device cloud gateway App. released.

First 8-bit Serial to Ethernet device networking module released. Building TCP/IP stack from the scratch.

First credit card size ARM9 + Linux SoM in Asia released. Ready to run application platform for low power computing.

ARM Cortex M3 + FreeRTOS based web enabled, remote I/O control series released.

Palm-size industrial box computer with auto system recovery feature released.

Intelligent IoT GatewayMatrix ARM-based box computer is a Linux / WinCE ready industrial computing platform designed for data concentration and device gateway. Built rugged, its extra low power RISC architecture makes fanless computing possible.

Featuring a fault resilient boot mechanism, Matrix can automatically boot up from backup data flash in case the on board NAND flash failed.

Matrix comes with Ethernet ports for wired networking and wireless LAN / 3G networking can be added by using USB dongles or miniPCIe cards.

For real time and small footprint applications such as protocol conversion and real time control, FreeRTOS is the choice of software operation platform. The Aport series come with ARM cortex M series controller plus FreeRTOS and programmer friendly APIs make your life easy.

IoT Device PlatformArtila M series ARM + Linux ready System on Module (SoM) is an application ready platform for device makers to reduce their cost and time in hardware and software design.

The M series SoM includes ARM SoC, memory and flash and pre-installed Linux OS in a credit card size module with 128 pin headers. The pre-loaded file system includes busybox utility collection, web server and USB device drivers.

M series SoM features Ethernet, UART, USB, SD interfaces and serial bus such as I2C, SPI and I2S. The 32 GPIOs are useful for input and output monitoring and control.

Programmable Automation ControllerPAC series is a Linux-based, C / C++ programmable automation controller. Network-enabled and web-ready PAC features rich analog and digital I/O for real world I/O control.

Based on M series SoM, PAC is a true Linux computing platform with file system support.

In order to deal with the harsh environment, PAC comes with 2500Vrms isolation in the analog and digital I/O and RS-485. A wide range power input function can also be found on the PAC family.

Web-based Remote I/OThe RIO family is a web ready, analog and digital I/O product lines which allows users to access and monitor the real world data using web interface or Modbus TCP / RTU protocols. RIO Series are based on the same hardware and

software architecture of Aport, therefore if you find functions which are not available then you can develop it by yourself by using the Aport FreeRTOS development kit. Windows and Linux API library are also included in the RIO family which will make access the RIO product easy.

Artila M series ARM + Linux ready System on

www.artila.com

Web Enables Remote Management

Based on open source Linux, Artila strives hard in maintaining its own repositories of Linux kernel, file system, daemons, utilities, C / C++ libraries to make our Linux platform robust with rich features while easy to use. Just focus on developing your domain specific applications, you don’t have to touch Linux details, let Artila do it for you. Artila’s Linux comes with standard ipkg tool for package management (install / update / uninstall) without dealing with the hell of library dependencies.

Artila’s Linux platform comes with ready-to-use lighttpd web server, MySQL / SQLite DBs and powerful PHP / Python script engines, all make our Linux platform meet all the requirements for Web / AJAX-enabled device monitoring and controls.

Linux KernelSupports version 2.6.29 and 2.6.38

File SystemUBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS

System Boot UpSupports booting up from: • On-boardNANDFlash(normalmode) • On-boardDataFlash(backup/restoremode) • SDcard(byrequest)

Network Protocol StacksIPv4, IPv6, ARP, DHCP, NTP, TCP, UDP, FTP, TELNET, HTTP, PPP, PPPoE, CHAP, PAP, SMTP, SNMP V1 / V2 / V3, SSL, SSH 1.0 / 2.0

Utilities (pre-installed) • bash,busybox,sysvinit,wget,ipkg,procps

(for webmin), psmics, vsftpd, iptables, ppp, ssh, wireless_tools, mount / umount, usbutils, Artila utilities

USB Host Drivers (built-in) Generic Flash drive, IEEE-802.11b/g WiFi adapter, Fast Ethernet adapter (RT8150), RS-232 adapter (Prolific PL-2303), Webcam, Keyboard / Mouse, 3G modem, ISDN modem (CDC / ACM compatible), Bluetooth

Web Service • Scripts:FastCGI,PHP5.2,Python2.6 • Database:MySQL5,SQLite3

Toolchain• GCC:C/C++crosscompiler• GLIBC:POSIXLibrary• GUIlibs:GTK+andQT/Embedded

Daemons (started by default) ssh, syslog, klogd, telnet, ftp, web server (lighttpd), amgrd (Artila broadcast search daemon)

02

Artila Linux Platform FeaturesLinux Toolchain

03

Intelligent IoT Gateway

• LowpowerARMSoCforwidetemperature

• LinuxandC/C++toolchainreadycomputerplatform

• EasytoexpandWLAN/3GwithUSBdongle/miniPCIe

• WEB/FTP/EMAIL/SNMP/PHP/JAVAready

• Palmsize,wallmountandDINRAILmount

ARM• LowpowerconsumptionRISC

• HighlyintegratedSoC(SystemonChip)

• Matureandmassmarkettechnology(Cellular,Tablet,etc.)

Linux• Marketprovenopentechnology(Server,Cellular,Switch,etc.)

• Completeapplicationbuildingblocks(Webserver,Java,PHP,etc.)

• Lifecycleisunderyourcontrol(Youownthesourcecode)

With worldwide experience in product integration, Artila’s products are widely used in power management, light control, access control system, parking facilities, solar energy system integration, RFID, environmental monitoring, and more.

• DataConcentration

• ProtocolConversion

• Front-endDeviceControl

• Web-basedDeviceManagement

Features

Application Proven

Other Applications

Looking for a reliable and tiny computer? ARM + Linux is what you need.

www.artila.com04

Matrix Series Selection GuideModel Matrix-500 Matrix-512 Matrix-504 Matrix-516 Matrix-518 Matrix-522 Matrix-604 Matrix-505 Matrix-513 Matrix-605 Matrix-618

CPUATMEL AT91RM9200

ARM9 180MHz ATMEL AT91SAM9G20

ARM926 400MHzATMEL AT91SAM9G45

ARM926 400MHz

RAM 64MB SDRAM 128MB DDR2 SDRAM

Flash 16MB NOR 256MB NAND

RTC Yes

Watchdog Timer

Yes

Battery SuperCAP Li 48mAh

No. of Serial Port

4 4 4 8 8 2 4 4 4 4 8

• RS-232 4 4 4 N/A 8 2 4 4 4 4 8

• RS-422 1 4 1 N/A 8 2 1 1 4 1 N/A

• RS-485 1 4 4 8 isolated 84 8 isolated 84 8 isolated 8 2 4 4 4 4 8

CAN Bus N/A N/A N/A N/A N/A 2 isolated N/AN/A 2 isolated N/AN/A 2 isolated N/A N/A N/A N/A N/AN/A N/A

Ethernet10/100Mbps

x 110/100Mbps

x 210/100Mbps

x 110/100Mbps

x 210/100Mbps

x 210/100Mbps

x 210/100Mbps

x 110/100Mbps

x 210/100Mbps

x 210/100Mbps

x 210/100Mbps

x 2

USB Host Full speed x 2 High speed x 2

USB Client Full speed x 1 High speed x 1

SD SD x 1 microSD x 1

GPIO N/A21-pin 3.3V

CMOS5-pin 3.3V

CMOS21-pin 3.3V

CMOS21-pin 3.3V

CMOS21-pin 3.3V

CMOS5-pin 3.3V

CMOSN/A

photocoupler x2 relay x1

N/A21-pin 3.3V

CMOS

Audio N/A N/A N/A N/A Yes N/A N/A N/A N/A N/A Yes

Power 9~48VDC 9~40VDC9~48VDC 9~40VDC 9~48VDC 9~40VDC 9~48VDC

Linux 2.6.14 2.6.29 N/A 2.6.38 N/A

WinCE N/A 6.0 N/A 6.0

Dimensions (W x H x D)

78 x 108 x 24mm

160 x 104 x 32mm

78 x 108 x 24mm

160 x 104 x 32mm 78 x 108 x 24mm 175 x 103 x

43mm78 x 108 x

24mm160 x 104 x

32mm

www.artila.com www.artila.com05 06

Linux-ready ARM9 Industrial Box Computer

H/W Specifications

TTY Pin Assignment Ordering Information

S/W Specifications

• Linux 2.6.14 compatible computing platform

• 64MB SDRAM and 16MB NOR Flash

• Ultra-low power consumption, less than 3 Watts

• 1 x 10/100Mbps Ethernet port

• 4 x 921.6Kbps high speed TTY (serial) ports

• 2 x USB 2.0 host ports for add-on functionality expansion

• 1 x SD memory card slot inside for storage expansion

• GNU C / C++ toolchain for Linux / Windows environment

• Extremely compact design, 78 x 108 x 24mm

CPU / Memory• CPU: ATMEL 180MHz AT91RM9200 (ARM9, w/ MMU)• Memory: 64MB SDRAM, 16MB NOR Flash

Network Interface• Type: 1 x 10/100BaseT, RJ45 connector• Protection: 1.5KV magnetic isolation

TTY (Serial) Ports• Port 1: Can be set as RS-232, RS-422 or RS-485• Port 2, 3, 4: RS-232• Connector: RJ45 connector

TTY (Serial) Port Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None

USB Host Ports• No. of Ports: 2• Speed: USB 2.0 compliant, supports low-speed (1.5Mbps) and full-speed (12Mbps) data rate

Mass Storage• 1 x SD 1.0 compliant socket inside

General• Watchdog Timer: Yes, for kernel use• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~48VDC• Power Consumption: 220mA@12VDC• Dimensions (W x H x D): 78 x 108 x 24mm• Operating Temperature: 0~70°C (32~158°F)• Regulation: CE Class A, FCC Class A

General• OS: Linux, kernel 2.6.14• Boot Loader: U-Boot 1.1.2• File Systems: JFFS2, ETX2 / ETX3, VFAT / FAT, NFS

Protocol Stacks• IPv4, ICMP, ARP, DHCP, NTP, TCP, UDP, FTP, TELNET, HTTP, PPP, PPPoE, CHAP, PAP, SMTP, SNMP V1 / V2, SSL, SSH 1.0 / 2.0

Pre-installed Utilities• bash: shell command• tinylogin: login and user manager utility• telnet: telnet client program• busybox: Linux utility collection• ftp: ftp client program

Daemons• pppd: dial in / out over serial port and PPPoE• snmpd: SNMP agent program• telnetd: telnet server program• inetd: TCP server program• ftpd: ftp server program• boa: web server program• sshd: secured shell server• iptables: firewall service manager• amgrd: Artila manager daemon

Toolchain for Linux• GCC: C / C++ PC cross complier• GLIBC: POSIX Library

Device Drivers• SD / MMC, UART, Real Time Clock, Buzzer, Digital I/O, Ethernet, Watchdog Timer

USB Host Drivers (Could Be Customized)• Flash disk, WiFi (IEEE-802.11b/g), and RS-232 adapters

CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G20 (ARM9, w/ MMU)• Memory: 64MB SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system backup


TTY (Serial) Ports• Port 1: Can be set as RS-232, RS-422 or RS-485• Port 2, 3, 4: Can be set as RS-232 or RS-485• Connector: RJ45 connector

TTY (Serial) Port Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None• RS-485 Direction Control: Auto, by hardware

USB Ports• Host Ports: 2• Client Port: 1, reserved• Speed: USB 2.0 compliant, supports low-speed (1.5Mbps) and full-speed (12Mbps) data rate

General• Watchdog Timer: Yes, for kernel use• Real Time Clock: Yes• Buzzer: Yes• microSD Socket: Yes• Power Input: 9~48VDC• Power Consumption: 250mA@12VDC• Dimensions (W x H x D): 78 x 108 x 24mm• Operating Temperature: 0~70°C (32~158°F)• Regulation: CE Class A, FCC Class A

General• OS: Linux, kernel 2.6.29• Boot Loader: U-Boot 1.1.2• File Systems: UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS

Pre-installed Utilities• bash, busybox, sysvinit, wget, ipkg, procps (for webmin), psmics, apache2, vsftpd, iptables, ppp, ssh, wireless_tools, util-linux-mount / umount, usbutils, Artila utility

Daemons Started by Default• ssh (secured shell) with sftp• syslog / klogd (system and kernel log)• telnet server (disable root permission in /etc/securetty)• ftp server (vsftp)• web server (apache2)• amgrd (Artila broadcast search daemon)

Package Management & System Administration• Supports ipkg to manage the package installation, upgrade and removal• Supports webmin (use ‘ipkg install webmin’ to install) for web-based system administration

Toolchain for Linux• GCC: C / C++ PC cross compiler• GLIBC: POSIX Library

USB Host Drivers• Generic Flash drive• RS-232 adapters (for Prolific PL-2303 compatibles)• WiFi dongles (for Ralink RT73 compatibles)

*: Port 2 only

Matrix-500

Features

H/W Specifications

TTY Pin Assignment

Ordering Information

S/W Specifications


• 64MB SDRAM and 256MB NAND Flash


• 1 x 10/100Mbps Ethernet port

• 4 x 921.6Kbps high speed TTY (serial) ports

• 2 x USB 2.0 host ports, 12Mbps

• 1 x microSD socket inside



Features

• Matrix-504 Linux-ready ARM9 Industrial Box Computer with 256MB on-board Flash and microSD Socket Inside

• Matrix-504T Wide-temperature (-20~80°C) Version of the Matrix-504

• 91-R45F9-150 Serial Cable (RJ45 to DB9 Female, 150cm)

• 91-RJCON-100 Console Cable (RJ45 to DB9 Female, 100cm)

• DK-35A DIN RAIL Mounting Kit

• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter

Linux-ready ARM9 Industrial Box ComputerMatrix-504

PIN RS-232 RS-422 RS-48512345678

DSRRTSGNDTxRx

DCDCTSDTR

---Tx+GNDTx-Rx+Rx-------

---Data+GNDData-

------------

*

*

*

PIN RS-232 RS-422 RS-48512345678

DSRRTSGNDTxRx

DCDCTSDTR


---Data+GNDData-

------------

1 8

1 8

• Matrix-500 Linux-ready ARM9 Industrial Box Computer with 16MB on-board Flash• 91-R45F9-150 Serial Cable (RJ45 to DB9 Female, 150cm)• 91-RJCON-100 Console Cable (RJ45 to DB9 Female, 100cm)• DK-35A DIN RAIL Mounting Kit• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter


H/W Specifications

TTY Pin Assignment


S/W Specifications


• 128MB DDR2 SDRAM and 256MB NAND Flash

• System backup Data Flash: 2MB

• 2 x 10/100Mbps Ethernet ports

• 1 x RS-232 / 422 / 485, 3 x RS-232 / 485 TTY ports

• 2 x USB 2.0 host ports, up to 480Mbps

• 1 x microSD socket inside



CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G45 (ARM9, w/ MMU)• Memory: 128MB DDR2 SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system backup

Network Interface• No. of Ports: 2, independent• Type: 10/100BaseT, RJ45 connector• Protection: 1.5KV magnetic isolation

TTY (Serial) Ports• Port 1: Can be set as RS-232 / 422 / 485• Port 2, 3, 4: Can be set as RS-232 / 485• Connector: RJ45 connector

TTY (Serial) Port Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2 • Flow Control: RTS / CTS, XON / XOFF, None• RS-485 Direction Control: Auto, by hardware

USB Ports• Host Ports: 2• Client Port: 1, reserved• Speed: USB 2.0 compliant, supports high-speed (480Mbps) mode

General• Watchdog Timer: Yes, for kernel use• Real Time Clock: Yes• Buzzer: Yes• microSD Socket: Inside the box, up to 32GB• Power Input: 9~48VDC• Power Consumption: 200mA@12VDC• Dimensions (W x H x D): 78 x 108 x 24mm• Operating Temperature: 0~70°C (32~158°F)• Regulation: CE Class A, FCC Class A


Pre-installed Utilities• bash, busybox, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, ssh, wireless_tools, util-linux-mount / umount, usbutils, Artila utility

Daemons Started by Default• ssh (secured shell) with sftp• syslog / klogd (system and kernel log)• telnet server (disable root permission in /etc/securetty)• ftp server (vsftp)• web server (lighttpd)• amgrd (Artila broadcast search daemon)






TTY (Serial) Ports• 4 x RS-232 / 422 / 485 ports, software select• Port 2: Supports full modem signals• Connector: DB9 male connector


USB Host Ports• No. of Ports: 2• Speed: USB 2.0 compliant, supports low-speed (1.5Mbps) and full-speed (12Mbps) data rate

Digital I/Os (GPIO)• No. of Pins: 21• Signal Level: CMOS / TTL compatible• Each pin can be programmed as input or output







Toolchain for Linux• GCC: C / C++ PC cross compiler for Linux, Cygwin• GLIBC: POSIX Library


USB Host Drivers (Could Be Customized)• Flash disk• WiFi (IEEE-802.11b/g)• RS-232 adapters

Matrix-505

Features

• Matrix-505 Linux-ready ARM9 Industrial Box Computer with 256MB on-board Flash


• 91-PHDF9-050 Console Cable (Wafer Box to DB9 Female, 50cm)



H/W Specifications


S/W Specifications


• 64MB SDRAM and 16MB NOR Flash


• 4 x 921.6Kbps RS-232 / 422 / 485 TTY ports

• 2 x USB 2.0 host ports for add-on functionality expansion

• 1 x SD memory card slot inside for storage expansion

• 21 x CMOS / TTL-level digital I/Os (GPIO)



Features

• Matrix-512 Linux-ready ARM9 Industrial Box Computer with 16MB on-board Flash• 91-DBCON-100 Console Cable (DB9 Female to DB9 Female, 100cm)• DK-35A DIN RAIL Mounting Kit

TTY Pin Assignment


*: Port 2 only

PIN RS-232 RS-422 RS-48512345678

DSRRTSGNDTxRx

DCDCTSDTR


---Data+GNDData-

------------

PIN RS-232 RS-422 RS-485DCDRxTx

DTRGNDDSRRTSCTS---

Tx-Tx+Rx+Rx-

GND------------

------

Data+Data-GND------------

*

*

*

1 8

1

6 7 8 9

2 3 4 5

123456789

9~40VDC 21 xGPIOs

2 x USB Hosts

2 x LANs

4 x TTY (Serial) Portssupport RS-232 / 422 / 485

Rear ViewFront View



H/W Specifications

TTY Pin Assignment


S/W Specifications

• ATMEL 400MHz ARM9 AT91SAM9G45 CPU

• 128MB DDR2 SDRAM and 256MB NAND Flash


• 2 x high-speed USB hosts, up to 480Mbps

• 1 x full size miniPCIe socket inside (USB signal)

• 1 x half size miniPCIe socket inside (USB signal)

• 4 x RS-232 / 422 / 485 serial ports

CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G45 w/ MMU• Memory: 128MB DDR2 SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system backup

Network Interface• Type: 2 x 10/100Mbps Ethernet, RJ45 connector• Protection: 1.5KV magnetic isolation

TTY (Serial) Ports• Type: RS-232 / 422 / 485, software select• Connector: DB9 male• Port 1, 3, 4: TX, RX, RTS, CTS, GND• Port 2: TX, RX, RTS, CTS, DCD, DTR, DSR, GND

USB Ports• Speed: Supports 480Mbps high-speed mode• Host Ports: 2• Client Port: 1

Digital I/Os• Inputs: 2 x 2500Vrms opto-isolation• Output: 1 x relay output (30VDC@1A), supports form A or B (by jumper)

SD Socket (Secure Digital Card)• Type: microSD• No. of Sockets: 1• Storage Capacity: Up to 32GB

General• Power Input: 9~48VDC• Power Consumption: 500mA@12VDC, max.• Dimensions (W x H x D): 175 x 103 x 43mm• Operating Temperature: 0~70°C• Regulations: CE Class A, FCC Class A

General• OS: Linux, kernel 2.6.38• Boot Loader: U-Boot• File Systems: UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS, NTFS



CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G20 w/ MMU• Memory: 64MB SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system backup


TTY (Serial) Ports• 8 x Isolated RS-485 (2500Vrms isolation)• Direction Control: Auto, by hardware• Connector: Terminal block• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2


SD Socket (Secure Digital Card)• Type: microSD• No. of Sockets: 1• Storage Capacity: Up to 32GB• Compatibility: SD memory specification 1.0


General• Watchdog Timer: Yes• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~48VDC• Power Consumption: 190mA@12VDC• Dimensions (W x H x D): 160 x 104 x 32mm• Operating Temperature: 0~70ºC (32~158ºF)• Regulation: CE Class A, FCC Class A


Pre-installed Utilities• bash, busybox, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, ssh, wireless_tools, util-linux-mount / umount, usbutils, Artila utility, and more





Matrix-513

Features

• Matrix-513 Linux-ready ARM9 Industrial Box Computer (Note: miniPCIe card, antenna and pigtail antenna cable are **NOT** included)

• 91-0P9M9-001 Console Cable (10Pin Header to DB9 Male, 20cm)• DK-35A DIN RAIL Mounting Kit• Pigtail-WiFi-1001-20 IPEX to RP-SMA Female Coaxial Cable, 20cm• Pigtail-3G-1001-20 IPEX to SMA Female Coaxial Cable, 20cm• Ant-WiFi-1001 5dBi External WiFi Antenna• Ant-3G-1001 5dBi External 2G / 3G Antenna• M-9001 (EWM-W150H) 802.11 b/g/n Half-size miniPCIe WiFi Card• M-9011 (CM5000) Full-size miniPCIe 2G / 3G Card, with SIM Socket• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter

H/W Specifications


S/W Specifications


• Linux kernel 2.6.29 with file system


• 1 x microSD socket inside, up to 32GB capacity


• 8 x isolated RS-485 serial ports

• 2 x USB hosts, 21 x GPIOs


Features

• Matrix-516 Linux-ready ARM9 Industrial Box Computer

• 91-0P9M9-001 Console Cable (10Pin Header to DB9 Male, 20cm)



Platform Features• Web server (lighttpd) with PHP 5, Python 2.6• MySQL 5, server and client• SQLite 3• SNMP V1 / V2 / V3• Java

USB miniPCIe Supports• Interface: Supports USB signals only• Full-size Socket: 1, suitable for 2G / 3G card• Half-size Socket: 1, suitable for WiFi card• Antenna Mounting Holes: 3, suitable for mounting SMA connectors

PIN RS-232 RS-422 RS-485

*: Port 2 only

*

*

*

123456789

DCDRxTx

DTRGNDDSRRTSCTS---

Tx-Tx+Rx+Rx-

GND------------

------


1

6 7 8 9

2 3 4 5

Rear View

9~48VDCInput

21 x GPIOs 2 x USB Hosts

2 x LANs

USB Client



H/W Specifications


S/W Specifications






• 8 x RS-232 / 422 / 485 serial ports

• USB / GPIO / Audio out




TTY (Serial) Ports• 8 x RS-232 / 422 / 485• Connector: RJ45 connector





Audio Output• MP3 and WAV format are supported

General• Watchdog Timer: Yes• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~40VDC• Power Consumption: 190mA@12VDC• Dimensions (W x H x D): 160 x 104 x 32mm• Operating Temperature: 0~70ºC (32~158ºF)









TTY (Serial) Ports• 2 x RS-232 / 422 / 485• Connector: DB9 male connector




CAN Bus Ports• Type: 2 x CAN bus 2.0A/B compliant ports• Speed: Up to 1Mbps• Isolation: 2500Vrms• Connector: DB9 male connector

General• Watchdog Timer: Yes• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~40VDC• Power Consumption: 190mA@12VDC• Dimensions (W x H x D): 160 x 104 x 32mm






USB Host Drivers• Generic Flash drive• RS-232 adapters (for Prolific PL-2303 compatibles)• WiFi dongles (rt2500 / rtl8187 / rt73 / zd1211 chips)

Matrix-518

Features





H/W Specifications


S/W Specifications





• 2 x CAN bus ports support SocketCAN / CANOpen


• 2 x RS-232 / 422 / 485 serial ports



Features

• Matrix-522 Linux-ready ARM9 Industrial CAN Bus Box Computer

• 91-DBCON-100 Console Cable (DB9 Female to DB9 Female, 100cm)



Rear View

Rear View

9~40VDCInput


2 x LANs

USB Client

9~40VDCInput


2 x LANs

USB Client



H/W Specifications


S/W Specifications






• 8 x RS-232 / 422 / 485 serial ports

• USB / GPIO / Audio out




TTY (Serial) Ports• 8 x RS-232 / 422 / 485• Connector: RJ45 connector





Audio Output• MP3 and WAV format are supported

General• Watchdog Timer: Yes• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~40VDC• Power Consumption: 190mA@12VDC• Dimensions (W x H x D): 160 x 104 x 32mm• Operating Temperature: 0~70ºC (32~158ºF)









TTY (Serial) Ports• 2 x RS-232 / 422 / 485• Connector: DB9 male connector




CAN Bus Ports• Type: 2 x CAN bus 2.0A/B compliant ports• Speed: Up to 1Mbps• Isolation: 2500Vrms• Connector: DB9 male connector

General• Watchdog Timer: Yes• Real Time Clock: Yes• Buzzer: Yes• Power Input: 9~40VDC• Power Consumption: 190mA@12VDC• Dimensions (W x H x D): 160 x 104 x 32mm







Matrix-518

Features





H/W Specifications


S/W Specifications





• 2 x CAN bus ports support SocketCAN / CANOpen


• 2 x RS-232 / 422 / 485 serial ports



Features

• Matrix-522 Linux-ready ARM9 Industrial CAN Bus Box Computer




Rear View

Rear View

9~40VDCInput


2 x LANs

USB Client

9~40VDCInput


2 x LANs

USB Client


PIN Console12345678

GPIO1Tx

GNDGPIO2GPIO3GPIO4

RxGPIO5

WinCE-ready ARM9 Industrial Box Computer

H/W Specifications


S/W Specifications

• Windows CE 6.0 compatible computing platform• ATMEL 400MHz ARM9 AT91SAM9G20 CPU• 64MB SDRAM and 256MB NAND Flash• Failover mechanism against system crash• 1 x 10/100Mbps Ethernet port• 4 x 921.6Kbps high speed RS-232 / 422 / 485 ports• 2 x USB 2.0 host ports, 12Mbps• C / C++ Static / Dynamic Libraries included• Supports Microsoft .NET Compact Framework 2.0• Extremely compact design, 78 x 108 x 24mm• Ultra-low power consumption, less than 3 Watts

CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G20 (ARM9, w/ MMU)• Memory: 64MB SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system recovery


COM Ports (RJ45 Connector)• COM 1: Can be set as RS-232, RS-422 or RS-485• COM 2, 3, 4: Can be set as RS-232 or RS-485

COM Port Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None• RS-485 Direction Control: Auto, by hardware

Console & GPIO (RJ45 Connector)• Console: Tx / Rx / GND, 115, 200, N81• GPIO: 5, CMOS level

USB Ports• Host Ports: 2• Client Port: 1, for ActiveSync• Speed: USB 2.0 compliant, supports low-speed (1.5Mbps) and full-speed (12Mbps) data rate


General• OS: WinCE 6.0• RAM-based File System: Up to 30MB free space available• NAND-based File System: Up to 90MB free space available

Ready-to-use Network Services• Web Server, including ASP support (users can specify the default directory of web pages)• Telnet Server• FTP Server• Remote Display Control (a Windows's client utility is included)

Artila Enhanced Command Mode Utility (Note: Utilities below are provided by Artila, not Microsoft)

• ifconfig: to modify the network interface settings• update: to update the kernel image and file system• init: to organize the application programs which run automatically after system boot-up• gpioctrl: to control the Matrix-604's GPIOs

System Failover Mechanism• Normally, the Matrix-604 boots up from its NAND Flash.• If the NAND Flash is crashed, the Matrix-604 can still boot up from its Data Flash. A menu-driven utility will be activated to help users to recover its NAND Flash.

Application Development & Deployment• It is recommended to use Microsoft Visual Studio 2005 for application development. The Matrix-604 comes with its own SDK for C / C++ programming language.• The application program can be transferred to the Matrix-604 either by ActiveSync or USB pen drive locally or by FTP remotely.

CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G45 (ARM9, w/ MMU)• Memory: 128MB DDR2 SDRAM, 256MB NAND Flash• DataFlash®: 2MB, for system recovery


COM Ports (RJ45 Connector)• COM 1: Can be set as RS-232, RS-422 or RS-485• COM 2, 3, 4: Can be set as RS-232 or RS-485


USB Ports• Host Ports: 2• Client Port: 1, for ActiveSync• Speed: USB 2.0 compliant, supports low-speed (1.5Mbps), full-speed (12Mbps) data rate, and high-speed (480Mbps)


General• OS: WinCE 6.0

Ready-to-use Network Services• Web Server, including ASP support (users can specify the default directory of web pages)• Telnet Server• FTP Server• Remote Display Control (a Windows's client utilty is included)

Artila Enhanced Command Mode Utility(Note: Utilities below are provided by Artila, not Microsoft)

• ifconfig: to modify the network interface settings• update: to update the kernel image and file system• init: to organize the application programs which run automatically after system boot-up


Application Development & Deployment• It is recommended to use Microsoft Visual Studio 2005 for application development. The Matrix-605 comes with its own SDK for C / C++ programming language.• The application program can be transferred to the Matrix-605 either by ActiveSync or USB pen drive locally or by FTP remotely.

Matrix-604

Features

• Matrix-604 WinCE-ready ARM9 Industrial Box Computer with 256MB on-board Flash





H/W Specifications


S/W Specifications

• Windows CE 6.0 compatible computing platform• ATMEL 400MHz ARM9 AT91SAM9G45 CPU• 128MB DDR2 SDRAM and 256MB NAND Flash• Failover mechanism against system crash• 2 x 10/100Mbps Ethernet ports• 4 x 921.6Kbps high speed RS-232 / 422 / 485 ports• 2 x USB 2.0 host ports, 480Mbps• C / C++ Static / Dynamic Libraries included• Supports Microsoft .NET Compact Framework 2.0• Extremely compact design, 78 x 108 x 24mm• Ultra-low power consumption, less than 3 Watts

Features

• Matrix-605 WinCE-ready ARM9 Industrial Box Computer with 256MB on-board Flash





WinCE-ready ARM9 Industrial Box ComputerMatrix-605

PIN Assignment

- Only COM 1 supports RS-422- Console port contains 5 x GPIO pins

PIN RS-23212345678

DSRRTSGNDTxRx

DCDCTSDTR


RS-422 RS-485---

Data+GNDData-

------------

PIN Console12345678

GPIO1Tx

GNDGPIO2GPIO3GPIO4

RxGPIO5

PIN Assignment

- Only COM 1 supports RS-422- Console port contains 5 x GPIO pins

PIN RS-23212345678

DSRRTSGNDTxRx

DCDCTSDTR


RS-422 RS-485---

Data+GNDData-

------------

1 8

1 8



H/W Specifications


S/W Specifications

• Windows CE 6.0 compatible computing platform• ATMEL 400MHz ARM9 AT91SAM9G45 CPU• 128MB DDR2 SDRAM and 256MB NAND Flash• Failover mechanism against system crash• 2 x 10/100Mbps Ethernet ports• 8 x 921.6Kbps high speed RS-232 / 485 ports• 2 x USB 2.0 host ports, 480Mbps• C / C++ Static / Dynamic Libraries included• Supports Microsoft .NET Compact Framework 2.0• Extremely compact design, 160 x 104 x 32mm• Ultra-low power consumption, less than 3 Watts



COM Ports (RJ45 Connector)• COM 1~8: Can be set as RS-232 and RS-485










Application Development & Deployment• It is recommended to use Microsoft Visual Studio 2005 for application development.The Matrix-618 comes with its own SDK for C / C++ programming language.• The application program can be transferred to the Matrix-618 either by ActiveSync or USB pen drive locally or by FTP remotely.

System• CPU: NXP LPC1768 Cortex M3 100MHz

Serial Port• Port 1: RS-232 / 422 / 485• Port 2: RS-232 / 485• Baud Rate: 1.2~921.6Kbps• Flow Control: None / Hardware / XON_XOFF• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 2• Protection: 15KV ESD


Serial Console Port• RS-232: 115.2Kbps baud rate, no flow control, 8 bits data, 1 stop bit

Mechanical & Environmental• Power: 9~40VDC power jack and terminal block• Dimensions (W x H x D): 78 x 108 x 25mm• Operating Temperature: 0~70°C• Storage Temperature: -20~85°C

Matrix-618

Features

• Matrix-618 WinCE-ready ARM9 Industrial Box Computer




H/W Specifications


• Low power ARM Cortex M3 100MHz SoC

• 512KB Flash and 32KB SRAM

• 1 x 10/100Mbps Ethernet

• 2 x RS-232 / 422 / 485 ports

• C / C++ Programmable with FreeRTOS

• lwIP and BSD socket library for TCP/IP

• Toolchain: Sourcery CodeBench Lite

• Example code: device server and web console

• Windows utility for firmware upgrade and configuration

Features

• Aport-212PG Programmable Device Server




Programmable Device ServerAport-212PG

Windows Utility Software

Example Program

PIN Assignment

- Console port contains 5 x GPIO pins

PIN RS-23212345678

DSRRTSGNDTxRx

DCDCTSDTR

---Data+GNDData-

------------

RS-485 1 8



H/W Specifications


S/W Specifications

• Windows CE 6.0 compatible computing platform• ATMEL 400MHz ARM9 AT91SAM9G45 CPU• 128MB DDR2 SDRAM and 256MB NAND Flash• Failover mechanism against system crash• 2 x 10/100Mbps Ethernet ports• 8 x 921.6Kbps high speed RS-232 / 485 ports• 2 x USB 2.0 host ports, 480Mbps• C / C++ Static / Dynamic Libraries included• Supports Microsoft .NET Compact Framework 2.0• Extremely compact design, 160 x 104 x 32mm• Ultra-low power consumption, less than 3 Watts



COM Ports (RJ45 Connector)• COM 1~8: Can be set as RS-232 and RS-485










Application Development & Deployment• It is recommended to use Microsoft Visual Studio 2005 for application development.The Matrix-618 comes with its own SDK for C / C++ programming language.• The application program can be transferred to the Matrix-618 either by ActiveSync or USB pen drive locally or by FTP remotely.

System• CPU: NXP LPC1768 Cortex M3 100MHz

Serial Port• Port 1: RS-232 / 422 / 485• Port 2: RS-232 / 485• Baud Rate: 1.2~921.6Kbps• Flow Control: None / Hardware / XON_XOFF• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 2• Protection: 15KV ESD



Mechanical & Environmental• Power: 9~40VDC power jack and terminal block• Dimensions (W x H x D): 78 x 108 x 25mm• Operating Temperature: 0~70°C• Storage Temperature: -20~85°C

Matrix-618

Features

• Matrix-618 WinCE-ready ARM9 Industrial Box Computer




H/W Specifications


• Low power ARM Cortex M3 100MHz SoC

• 512KB Flash and 64KB SRAM

• 1 x 10/100Mbps Ethernet

• 2 x RS-232 / 422 / 485 ports

• C / C++ Programmable with FreeRTOS

• lwIP and BSD socket library for TCP/IP

• Toolchain: Sourcery CodeBench Lite

• Example code: device server and web console

• Windows utility for firmware upgrade and configuration

Features

• Aport-212PG Programmable Device Server




Programmable Device ServerAport-212PG

Windows Utility Software

Example Program

PIN Assignment

- Console port contains 5 x GPIO pins

PIN RS-23212345678

DSRRTSGNDTxRx

DCDCTSDTR

---Data+GNDData-

------------

RS-485 1 8


www.artila.com17 18

IoT Device Platform

• Ultralowpower32-bitARMprocessor

• Built-inLinuxOSwithGNUC/C++compiler

• Completedevicedriverandutilitysupport

• Reliable128-pin2.0mmpinheader

• Compact50x80mmfootprint

SBCModel M-506 M-508 M-606

CPUATMEL AT91-

SAM9G45400MHz

ATMEL AT91RM9200

180MHz

ATMEL AT91-SAM9G45400MHz

Floating Point Unit

N/A N/A N/A

RAM128MB DDR2

SDRAM64MB SDRAM

128MB DDR2 SDRAM

Flash 256MB NAND 32MB NOR 256MB NAND

Graphics24-bit TTL LCD

and LVDSN/A

24-bit TTL LCD and LVDS

Multimedia N/A N/A N/A

2D / 3D Acc. N/A N/A N/A

RTC Yes Yes Yes

Watchdog Timer

Yes Yes Yes

Battery Li 48mAH SuperCap Li 48mAH

SerialRS-232 x 3,

RS-422 / 485 x 1

RS-232 / 422 / 485 x 1,

RS-232 / 485 x 3

RS-232 x 3, RS-422 / 485 x 1

Console 1 1 1

Ethernet 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1

USB Host High speed x 4 Full speed x 2 High speed x 4

USB Client 1 1 1

SD / MMC microSD x 1 SD x 1 microSD x 1

GPIO 4 32 4

Power 12~40VDC 5VDC 12~40VDC

Linux 2.6.38 2.6.14 N/A

WinCE N/A N/A 6.0

Dimensions (W x H)

146 x 102mm 105 x 75mm 146 x 102mm

Long-Term Partnership with ARM

Features

Appearance Block Diagram

SoMModel M-501 M-502 M-503 M-9G45A M-5360A

CPUATMEL

AT91RM9200180MHz

ATMEL AT91-SAM9G20ARM926 400MHz



Freescale i.MX537

Cortex A8 800MHz

Floating Point Unit

N/A N/A N/A N/A 32-bit

RAM 64MB SDRAM 64MB SDRAM128MB DDR2

SDRAM128MB DDR2

SDRAM1GB DDR3

SDRAM

Flash 16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC

Graphics N/A N/A N/A24-bit LCD CMOS out

24-bit LCD LVDS x 2 and VGA

Multimedia N/A N/A N/A N/A 1080p

2D / 3D Acc. N/A N/A N/A N/AOpenGLE 1.1

& 2.0Open-VG 1.1

RTC N/A Yes Yes Yes Yes

Watchdog Timer

Yes Yes Yes Yes Yes

Battery N/A Li 48mAHLi 48mAH or

ExternalLi 48mAH External

UART 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 1

Console RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1

Ethernet 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1

USB Host Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1

USB Client Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1

SD / MMC 1 1 1 1 1

SATA N/A N/A N/A N/A 1

Touch N/A N/A N/A 1 1

Local Bus 8-bit 8-bit 8-bit N/A N/A

I2C 1 1 1 1 1

I2S (audio) 1 1 1 1 1

SPI 1 1 1 1 1

CAN Bus N/A N/A N/A N/A 1

GPIO32-pin 3.3V

CMOS32-pin 3.3V

CMOS32-pin 3.3V

CMOS15-pin 3.3V

CMOS6-pin 3.3V

CMOS

Power 3.3VDC 3.3VDC 3.3VDC 3.3VDC 5VDC / 3.3VDC

Linux 2.6.14 2.6.29 2.6.38 2.6.38 2.6.35

A solid foundation for 32-bit ARM® processor-based MCUs

www.artila.com18

SBCModel M-506 M-508 M-606

CPUATMEL AT91-

SAM9G45 400MHz

ATMEL AT91RM9200

180MHz

ATMEL AT91-SAM9G45400MHz

Floating Point Unit

N/A N/A N/A

RAM128MB DDR2

SDRAM64MB SDRAM

128MB DDR2 SDRAM

Flash 256MB NAND 32MB NOR 256MB NAND256MB NAND 32MB NOR 256MB NAND256MB NAND 32MB NOR 256MB NAND

Graphics24-bit TTL LCD

and LVDSN/A

24-bit TTL LCD and LVDS

Multimedia N/A N/A N/A

2D / 3D Acc. N/A N/A N/A

RTC Yes Yes Yes

Watchdog Timer

Yes Yes Yes

Battery Li 48mAH SuperCap Li 48mAHLi 48mAH SuperCap Li 48mAHLi 48mAH SuperCap Li 48mAH

SerialRS-232 x 3,

RS-422 / 485 x 1

RS-232 / 422 / 485 x 1,

RS-232 / 485 x 3

RS-232 x 3, RS-422 / 485 x 1

Console 1 1 1

Ethernet 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1

USB Host High speed x 4 Full speed x 2 High speed x 4High speed x 4 Full speed x 2 High speed x 4High speed x 4 Full speed x 2 High speed x 4

USB Client 1 1 1

SD / MMC microSD x 1 SD x 1 microSD x 1microSD x 1 SD x 1 microSD x 1microSD x 1 SD x 1 microSD x 1

GPIO 4 32 4

Power 12~40VDC 5VDC 12~40VDC12~40VDC 5VDC 12~40VDC12~40VDC 5VDC 12~40VDC

Linux 2.6.38 2.6.14 N/A

WinCE N/A N/A 6.0

Dimensions (W x H)

146 x 102mm 105 x 75mm 146 x 102mm146 x 102mm 105 x 75mm 146 x 102mm146 x 102mm 105 x 75mm 146 x 102mm

SoMModel M-501 M-502 M-503 M-9G45A M-5360A

CPUATMEL

AT91RM9200180MHz




Freescale i.MX537

Cortex A8 800MHz

Floating Point Unit

N/A N/A N/A N/A 32-bit

RAM 64MB SDRAM 64MB SDRAM64MB SDRAM 64MB SDRAM128MB DDR2

SDRAM128MB DDR2

SDRAM1GB DDR3

SDRAM

Flash 16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC16MB NOR 256MB NAND 256MB NAND 256MB NAND 4GB eMMC

Graphics N/A N/A N/A24-bit LCD CMOS out

24-bit LCD LVDS x 2 and VGA

Multimedia N/A N/A N/A N/A 1080p

2D / 3D Acc. N/A N/A N/A N/AOpenGLE 1.1

& 2.0Open-VG 1.1

RTC N/A Yes Yes Yes Yes

Watchdog Timer

Yes Yes Yes Yes Yes

Battery N/A Li 48mAHLi 48mAH or

ExternalLi 48mAH ExternalLi 48mAH External

UART 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 14-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 14-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 14-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 14-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 3, full x 1 4-wire x 2, full x 1

Console RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1RS-232 x 1 RS-232 x 1 RS-232 x 1 RS-232 x 1 4-wire TTL x 1

Ethernet 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 110/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1 10/100Mbps x 1

USB Host Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1Full speed x 2 Full speed x 2 High speed x 1 High speed x 1 High speed x 1

USB Client Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1Full speed x 1 Full speed x 1 High speed x 1 High speed x 1 High speed x 1

SD / MMC 1 1 1 1 1

SATA N/A N/A N/A N/A 1

Touch N/A N/A N/A 1 1

Local Bus 8-bit 8-bit 8-bit N/A N/A

I2C 1 1 1 1 1

I2S (audio) 1 1 1 1 1

SPI 1 1 1 1 1

CAN Bus N/A N/A N/A N/A 2

GPIO32-pin 3.3V

CMOS32-pin 3.3V

CMOS32-pin 3.3V

CMOS15-pin 3.3V

CMOS6-pin 3.3V

CMOS

Power 3.3VDC 3.3VDC 3.3VDC 3.3VDC 5VDC / 3.3VDC3.3VDC 5VDC / 3.3VDC

Linux 2.6.14 2.6.29 2.6.38 2.6.38 2.6.35

Linux-ready ARM9 System on Module

H/W Specifications Ordering Information

• ATMEL 180MHz AT91RM9200 CPU w/ MMU• Linux kernel 2.6.14 with file system• 64MB SDRAM and 16MB NOR Flash• 1 x 10/100Mbps Ethernet• 2 x USB 2.0 hosts supporting full speed of 12Mbps• 1 x SD (secure digital) interface• 4 x 921.6Kbps UARTs w/ hardware flow control• External local bus (A0~A7, D0~D7, RD, WR), with 4 x chip select signals• Ultra-low power consumption, less than 2.5 Watts• GNU C / C++ toolchain is included

CPU / Memory• CPU: ATMEL 180MHz AT91RM9200 w/ MMU• Memory: 64MB SDRAM, 16MB NOR Flash

Network Interface• Type: 1 x 10/100Mbps Ethernet• PHY: DAVICOM DM9161• Protection: 1.5KV magnetic isolation

UART• Port 0: TXD0, RXD0, RTS0, CTS0, GND• Port 1: TXD1, RXD1, RTS1, CTS1, DCD1, DTR1, DSR1, GND• Port 2: TXD2, RXD2, RTS2, CTS2, GND• Port 3: TXD3, RXD3, RTS3, CTS3, GND• Signal Level: CMOS / 3.3V compatible

Common UART Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None

UART Advanced Feature (When Used as RS-485)• Supports 9-bit Multi-drop mode• Supports hardware auto direction control

USB Ports• Host Ports: 2, USB 2.0 compliant• Host Signals: UdataA+, UdataA-, UdataB+, UdataB-

I2C (Inter-IC Bus)• Signals: TWD, TWCK• Supported Devices: Driver has been built-in

I2S (Inter-IC Sound)• Transmitter Signals: TSCK, TWS, TSD• Receiver Signals: RSCK, RWS, RSD

SPI (Serial Peripheral Interface)• Signals: MISO, MOSI, SPCK, CS1, CS2

SD (Secure Digital Card Interface)• Signals: MCCDA, MCCK, MCDA0~MCDA3• Compatible with SD memory card specification 1.0

Watchdog Timer• CPU built-in internal watchdog timer, used by Linux kernel

GPIO (General-purpose I/Os)• 32 x GPIOs can be programmed as digital input or output• Supports interrupt function when GPIOs are set as digital input• Signal Level: CMOS / 3.3V compatible

Pre-defined Pins• Reset Button (CN2, pin#35), input• Buzzer (CN2, pin#37), output• 2-pin DIP SW (CN2, pin#12, #13), input• System ready LED (CN2, pin#38), output• LAN activity LED (CN3, pin#11), output

Undefined Digital I/O Pins (Reserved)• CN1: pin#23, #24, #25, #26• CN3: pin#23, #24

Debug Ports• Console Port: Tx / Rx serial console (share RTS2, CTS2)

Local Bus• Data Bus: 8-bit (D0~D7)• Address Bus: 8-bit (A0~A7)• Chip Select: x 4 (CS3, CS4, CS5, CS6)• Control Bus: RD, WR• Signal Level: CMOS / 3.3V compatible

Power Consumption• Input Range: 3~3.6VDC (3.3V nominal)• Consumption: 2W

General• Board Dimensions (W x H): 80 x 50mm• 2.0mm Pitch Connectors• CN1: 28 pins; CN2: 50 pins; CN3: 50 pins• Mounting Holes: x 4, 2.0mm (M2) in diameter• Operating Temperature: - M-501: 0~70°C (32~158°F) - M-501T: -20~80°C (-4~176°F)

M-501

Features

• M-501 AT91RM9200 + Linux 2.6.14 System on Module with 64MB SDRAM, 16MB NOR Flash

• M-501T AT91RM9200 + Linux 2.6.14 System on Module with 64MB SDRAM, 16MB NOR Flash, Wide-temp. Version

• M-501 Starter Kit Includes one M-501 SoM and one carrier board with power circuitry, 3 x RS-232 ports, 1 x RS-232 / 422 / 485 port, 1 x Ethernet port, 2 x USB hosts, 1 x SD socket (at rear side), 2 x GPIO connectors, Real Time Clock, EEPROM, and local bus connector

Linux-ready ARM9 System on ModuleM-501

S/W SpecificationsGeneral• OS: Linux, kernel 2.6.14• Boot Loader: U-Boot 1.1.2• File Systems: JFFS2, ETX2, VFAT / FAT, NFS

Pre-installed Utilities• bash, busybox, wget, boa, iptables, ppp, ssh, wireless_tools, Artila utility

Daemons Started by Default• ssh (secured shell)• syslog / klogd (system and kernel log)• telnet server (disable root permission in /etc/securetty)• ftp server (vsftp)• web server (lighttpd)• amgrd (Artila broadcast search daemon)


Standard Device Drivers• SD / MMC, UART, Ethernet, GPIO, Buzzer• Real Time Clock: Supports Ricoh RS5C372• EEPROM: Supports ATMEL AT24C16 and its compatibles

Pre-load USB Host Drivers (Could Be Customized)• Generic Flash drive• IEEE-802.11b/g WiFi adapter (Ralink rt73usb)• 10/100Mbps Fast Ethernet adapter (RT8150)• RS-232 adapter (Prolific PL-2303)• ADSL modem• ISDN modem (CDC / ACM compatible)

Front View Rear View

Console

SDRAM

Flash

CPU

SDRAM

TransformerPHY CN2

CN1

CN3

80mm

50m

m



H/W Specifications

• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• 1 x 10/100Mbps Ethernet• 2 x USB 2.0 hosts supporting full speed of 12Mbps• 1 x SD (secure digital) interface• 4 x 921.6Kbps UARTs w/ hardware flow control• 32 x GPIOs, CMOS / 3.3V compatible• Compact size, 50 x 80mm only• Ultra-low power consumption, less than 2.5 Watts• GNU C / C++ toolchain is included

Watchdog Timer• CPU built-in internal watchdog timer, used by Linux kernel• Additional watchdog timer is available for users’ applications

GPIO (General-purpose I/Os)• 32 x GPIOs can be programmed as digital input or output• Signal Level: CMOS / 3.3V compatible

Pre-defined Pins• Reset Button (CN2, pin#35), input• Buzzer (CN2, pin#37), output• 2-pin DIP SW (CN2, pin#12, #13), input• System ready LED (CN2, pin#38), output• LAN activity LED (CN3, pin#11), output

Real Time Clock• Chip: ST M41T81• Backup Battery: Lithium, 48mAh

Debug Ports• JTAG Port: for low level debug• Console Port: RS-232 (Tx / Rx) serial console

Local Bus• Data Bus: 8-bit (D0~D7)• Address Bus: 8-bit (A0~A7)• Chip Select: x 3 (CS0, CS5, CS6)• Control Bus: RD, WR• Signal Level: CMOS / 3.3V compatible

Power Consumption• Input Range: 3~3.6VDC (3.3V nominal)• Consumption: 2W

General• Board Dimensions (W x H): 80 x 50mm• 2.0mm Pitch Connectors• CN1: 28 pins; CN2: 50 pins; CN3: 50 pins• Mounting Holes: x 4, 2.0mm (M2) in diameter• Operating Temperature: 0~70°C (32~158°F)


Network Interface• Type: 1 x 10/100Mbps Ethernet• PHY: DAVICOM DM9161• Protection: 1.5KV magnetic isolation

UART• Port 0: TXD0, RXD0, RTS0, CTS0, GND• Port 1: TXD1, RXD1, RTS1, CTS1, DCD1, DTR1, DSR1, GND• Port 2: TXD2, RXD2, RTS2, CTS2, GND• Port 3: TXD3, RXD3, RTS3, CTS3, GND• Signal Level: CMOS / 3.3V compatible


UART Advanced Feature (When Used as RS-485)• Supports 9-bit Multi-drop mode• Supports hardware auto direction control

USB Ports• Host Ports: 2, USB 2.0 compliant• Host Signals: UdataA+, UdataA-, UdataB+, UdataB-• Device (Client): 1, USB 2.0 compliant• Device (Client) Signals: Uddata+, Uddata-, Udio

I2C (Inter-IC Bus)• Signals: TWD, TWCK• Supported Devices: Driver has been built-in


SPI (Serial Peripheral Interface)• Signals: MISO, MOSI, SPCK, CS1, CS2

SD (Secure Digital Card Interface)• Signals: MCCDA, MCCK, MCDA0~MCDA3• Compatible with SD memory card specification 1.0

M-502

Features

S/W Specifications



Pre-installed Utilities• bash, busybox, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, ssh, wireless_tools, util-linux-mount / umount, usbutils, Artila utility




Standard Device Drivers• Real Time Clock, SD / MMC, UART, Ethernet, GPIO, Buzzer• EEPROM: Supports ATMEL AT24C16 and its compatibles

Pre-load USB Host Drivers (Could Be Customized)• Generic Flash drive• IEEE-802.11b/g WiFi adapter (Ralink rt73usb, Ralink rt2500usb, Realtek RTL8187, ZyDAS zd1211rw)• 10/100Mbps Fast Ethernet adapter (RT8150)• RS-232 adapter (Prolific PL-2303)• ADSL modem• ISDN modem (CDC / ACM compatible)

Ordering Information• M-502 ATMEL9G20 + Linux 2.6.29 System on Module with 256MB NAND Flash, 64MB SDRAM


Front View Rear ViewBattery RTC SDRAM Console

PHY

Transformer

CPU DataFlash NAND Flash CN2

CN1

CN3

80mm

50m

m

SDRAM



H/W Specifications

• ATMEL 400MHz AT91SAM9G45 CPU w/ MMU• Linux kernel 2.6.38 with file system• 128MB DDR2 SDRAM and 256MB NAND Flash• GNU C / C++ toolchain is included• 1 x 10/100Mbps Ethernet interface, with PHY and transformer on board• 4 x 921.6Kbps UARTs w/ hardware flow control• 1 x USB 2.0 host supporting high speed of 480Mbps • 1 x SD (secure digital) interface, 1 x I2C interface, 1 x I2S interface, 1 x transmitter and 1 x receiver• 1 x SPI interface with two chip selects

SD (Secure Digital Card Interface)• Data Signals: MCCDA, MCCK, MCDA0~MCDA3• Aux. Signals: CD (Card Detection), WP (Write Protect)• Compatibility: SD memory card specification 2.0• Storage Capacity: Up to 32GB

Watchdog Timer• CPU built-in watchdog timer, used by Linux kernel• Additional watchdog timer is available for users’ applications

GPIO (General-purpose I/Os)• No. of Pins: 32, PIO0~PIO32, for input / output• IRQ Support: PIO32 only• Signal Level: CMOS / 3.3V compatible

Pre-defined I/O Pins• Reset Button (CN2, pin#35), input• System Reset (CN2, pin#34), input / output• Buzzer (CN2, pin#37), output• System Ready LED (CN2, pin#38), output• LAN activity LED (CN3, pin#11), output

Real Time Clock• Chip: ST M41T81• Backup Battery: Lithium, 48mAh, on-board• External Battery Input: on CN1 pin#5

Debug Ports• Type: RS-232 serial console• Signals: Tx, Rx, GND

Power Consumption• Input Range: 3~3.6VDC (3.3V nominal)• Consumption: 2 Watts typ.

General• Board Dimensions (W x H): 80 x 50mm• Pins: Total 128 pins, 2.0mm pitch CN1: 28 pins; CN2: 50 pins; CN3: 50 pins• Mounting Holes: x 2, 2.0mm (M2) in diameter


Network Interface• Type: 1 x 10/100Mbps Ethernet• Signals: ETX+, ETX-, ERX+, ERX-• PHY: DAVICOM DM9161, on-board• Protection: 1.5KV magnetic isolation

UART• UART 1: TX, RX, RTS, CTS, GND• UART 2: TX, RX, RTS, CTS, DCD, DTR, DSR, GND• UART 3: TX, RX, RTS, CTS, GND• UART 4: TX, RX, RTS, CTS, GND• Signal Level: CMOS / 3.3V compatible

Common UART Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data bits: 5, 6, 7, 8• Stop bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None

USB Ports• Speed: Supports 480Mbps high-speed mode• Host Port: 1, USB 2.0 compliant• Host Signals: USBA+, USBA-• Device (Client): 1, USB 2.0 compliant• Device (Client) Signals: Uddata+, Uddata-, Udio

I2C (Inter-IC Bus)• Signals: TWD, TWCK• Supported Devices: EEPROM, Real Time Clock


SPI (Serial Peripheral Interface)• Data Signals: MISO, MOSI, SPCK• Chip Selects: CS1, CS2

M-503

Features

S/W Specifications


General• OS: Linux, kernel 2.6.38• Boot Loader: U-Boot

File Systems• UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS, NTFS

Pre-installed Utilities• bash, busybox, gtk+, x11, gpe, alsa, madplayer, psplash, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, openssh, wireless_tools, util-linux-mount / umount, usbutils, python, jamvm, php, mysql, perl, qt4-embedded, sqlite3, snmp, Artila utility and more



IPKG Package Management• Supports ipkg to manage the package installation, upgrade and removal

Webmin System Administration• Supports webmin for web-based system administration

Standard Device Drivers• Real Time Clock, SD / MMC, UART, Ethernet, GPIO, Buzzer, EEPROM (ATMEL AT24C16 and compatibles), Audio out

Pre-load USB Device Drivers (Could Be Customized)• Generic Flash drive• IEEE-802.11b/g WiFi adapter• 10/100Mbps Fast Ethernet adapter (RT8150)• RS-232 adapter (Prolific PL-2303)• Webcam• Keyboard / Mouse• 3G modem• ISDN modem (CDC / ACM compatible)• Bluetooth

Ordering Information• M-503 AT91SAM9G45 + Linux 2.6.38 System on Module with 256MB NAND Flash, 128MB DDR2 SDRAM



CN2

CN1

CN3

80mm

50m

m

CPU Battery

ConsolePHY

Transformer

DDR2 SDRAM NAND Flash



H/W Specifications

• ATMEL 400MHz AT91SAM9G45 CPU w/ MMU• Linux kernel 2.6.38 with file system• 128MB DDR2 SDRAM and 256MB NAND Flash• GNU C / C++ toolchain is included• Compact size, 50 x 80mm only• Ultra-low power consumption, less than 2.5 Watts• 24-bit TTL LCD interface with dimming control, supports TFT panel up to 1280 x 860 pixels• Supports 4-wire touchscreen• 1 x 10/100Mbps Ethernet interface, with PHY and transformer on board

Watchdog Timer• CPU built-in watchdog timer, used by Linux kernel• Additional watchdog timer is available for users’ applications

GPIO (General-purpose I/Os)• No. of Pins: 15, PIO0~PIO14• Signal Level: CMOS / 3.3V compatible

AC97 Interface• Signals: RX, TX, FS, CK (Note: signals are shared with GPIOs, PIO11~14)

Pre-defined I/O Pins• Reset Button (CN1, pin#11), input• System Reset (CN1, pin#13), input / output• Buzzer (CN1, pin#22), output• System Ready LED (CN1, pin#1), output• LAN Activity LED (CN1, pin#3), output

Real Time Clock• Chip: ST M41T81• Backup Battery: Lithium, 48mAh, on-board• External Battery Input: on CN1 pin#5

Debug Ports• Type: RS-232 serial console• Signals: Tx, Rx, GND

LCD Interface (TTL)• Resolution: Up to 1280 x 860 TFT• RGB Signals (24-bit): Red x 8, Green x 8, Blue x 8• Control Signals: Dot Clock, Data Enable, H.sync, V.sync, Dimming (contrast), Backlight

Touchscreen Interface• Type: Support 4-wire touchscreen• Signals: Top, Bottom, Left, Right

Power Consumption• Input Range: 3~3.6VDC (3.3V nominal)• Consumption: 2 Watts typ.

General• Board Dimensions (W x H): 80 x 50mm• Pins: Total 128 pins, 2.0mm pitch CN1: 28 pins; CN2: 50 pins; CN3: 50 pins• Mounting Holes: x 2, 2.0mm (M2) in diameter


Network Interface• Type: 1 x 10/100Mbps Ethernet• Signals: ETX+, ETX-, ERX+, ERX-• PHY: DAVICOM DM9161, on-board• Protection: 1.5KV magnetic isolation

UART• UART 1: TX, RX, RTS, CTS, DCD, DTR, DSR, GND• UART 2: TX, RX, RTS, CTS, GND• UART 3: TX, RX, RTS, CTS, GND• UART 4: TX, RX, RTS, CTS, GND• Signal Level: CMOS / 3.3V compatible


USB Ports• Speed: Supports 480Mbps high-speed mode• Host Port: 1, USB 2.0 compliant• Host Signals: USBA+, USBA-• Device (Client): 1, USB 2.0 compliant• Device (Client) Signals: Uddata+, Uddata-, Udio

I2C (Inter-IC Bus)• Signals: TWD, TWCK• Supported Devices: EEPROM, Real Time Clock


SPI (Serial Peripheral Interface)• Data Signals: MISO, MOSI, SPCK• Chip Selects: CS1, CS2

SD (Secure Digital Card Interface)• Data Signals: MCCDA, MCCK, MCDA0~MCDA3• Aux. Signals: CD (Card Detection), WP (Write Protect)• Compatibility: SD memory card specification 2.0• Storage Capacity: Up to 32GB

M-9G45A

Features

S/W Specifications

Linux-ready ARM9 System on ModuleM-9G45A

General• OS: Linux, kernel 2.6.38• Boot Loader: U-Boot

File Systems• UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS, NTFS

Pre-installed Utilities• bash, busybox, gtk+, x11, gpe, alsa, madplayer, psplash, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, openssh, wireless_tools, util-linux-mount / umount, usbutils, python, jamvm, php, mysql, perl, qt4-embedded, sqlite3, snmp, Artila utility and more


Toolchain for Linux• GCC: C / C++ PC cross compiler• GLIBC: POSIX Library• GUI: GTK+, X window (X11), GPE and QT4-Embedded

IPKG Package Management• Supports ipkg to manage the package installation, upgrade and removal

Webmin System Administration• Supports webmin for web-based system administration

Standard Device Drivers• LCD, Real Time Clock, SD / MMC, UART, Ethernet, GPIO, Buzzer, EEPROM (ATMEL AT24C16 and compatibles), Audio out

Pre-load USB Device Drivers (Could Be Customized)• Generic Flash drive• IEEE-802.11b/g WiFi adapter• 10/100Mbps Fast Ethernet adapter (RT8150)• RS-232 adapter (Prolific PL-2303)• Webcam• Keyboard / Mouse• 3G modem• ISDN modem (CDC / ACM compatible)• Bluetooth

Ordering Information• M-9G45A AT91SAM9G45 + Linux 2.6.38 System on Module with 256MB NAND Flash, 128MB DDR2 SDRAM

• M-9G45A Starter Kit Includes one M-9G45A SoM and one carrier board with power circuitry, 1 x RS-485 port, 3 x RS-232 ports, 1 x Ethernet port, 4 x USB hosts, 1 x USB client, 1 x microSD socket, Real Time Clock, EEPROM, and local bus connector


CN2

CN1

CN3

80mm

50m

m

CPU Battery

Console

PHY

Transformer

DDR2 SDRAM NAND Flash


i.MX537 Cortex A8 System on Module

H/W Specifications


• Freescale i.MX537 Cortex A8 800MHz• 1GB DDR3 SDRAM, 4GB eMMC Flash• 24-bit LCD LVDS x 2• Analog VGA x 1• Support full HD 1080p video decode• Support OpenGLE 2.0 & OpenVG 1.1• 1 x 10/100Mbps Ethernet with PHY• 4 x UART ports• 1 x USB 2.0 host and 1 x USB OTG• SATA, SD, SPI, I2C, I2S, 1-Wire, GPIO and CAN 2.0• OS: Linux, Android and Windows Compact 7.0

System• CPU: Freescale i.MX537 Cortex A8 800MHz• Memory: 1GB DDR3 SDRAM, 4GB eMMC Flash• LCD: 24-bit LCD LVDS x 2 up to 1600 x 1200 pixels• VGA: Analog VGA out x 1 (Sync. with LVDS port0)• Multimedia: 1080p Full HD• 2D / 3D Accelerator: OpenGLE 1.1 & 2.0, OpenVG 1.1• RTC: Yes• Watchdog: Yes• Battery: External

Network Interface• Type: 1 x 10/100Mbps Ethernet with PHY

UART• 3 x 921.6Kbps • COM 1: TX, RX, RTS, CTS, DCD, DSR, DTR, GND• COM 2: TX, RX, RTS, CTS, DCD, DSR, DTR, GND• COM 3: TX, RX, RTS, CTS, GND• COM 4 (Serial Console): TX, RX, GND

USB Ports• Host Port: 1• Speed: USB 2.0 compliant, supports high-speed mode (480Mbps)• Host OTG Port: 1

General• SD card interface x 1, Up to 32GB• SATA x 1• Touch Screen: 4 wires• CAN bus x 2, CAN 2.0• Serial Interface: I2C x 1, I2S x 1, SPI x 1



TTY (Serial) Ports• 3 x RS-232 (Port 1, 3, 4)• 1 x RS-422 / 485 (Port 2)• Connector: 1 x DB9 and 2 x 10 pins header (male) for RS-232 Terminal Block for RS-422 / 485


USB Ports• Host Ports: 4, USB 2.0 compliant• Speed: Supports low-speed (1.5Mbps), full-speed (12Mbps) and high-speed (480Mbps)• Client Port: 1 x USB 2.0• Speed: High-speed (480Mbps)

Display Interface• LCD Resolution: Up to 1280 x 860 TFT• Interface Signal: 24-bit TTL / CMOS and LVDS• Touch Screen: 4-wire touch screen

GPIO (General-purpose I/Os)• No. of Pins: 4• Signal Level: CMOS / TTL compatible• Each pin can be programmed as input or output

General• Watchdog Timer: Yes• Real Time Clock: Yes, with backup battery• Buzzer: Yes• Power Input: 12~40VDC• Power Consumption: 200mA@12VDC• Board Dimensions (W x H): 146 x 120mm• Operating Temperature: 0~70ºC (32~158ºF)

M-506:General• OS: Linux, kernel 2.6.38• Boot Loader: U-Boot 1.1.2• File Systems: UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS

Pre-installed Utilities• bash, busybox, gtk+, x11, gpe, alsa, madplayer, psplash, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, openssh, wireless_tools, util-linux-mount / umount, usbutils, python, jamvm, php, qt4-embedded, mysql, perl, sqlite3, snmp, Artila utility and more

Toolchain for Linux• GCC: C / C++ PC cross compiler• GLIBC: POSIX Library• GUI: GTK+, X window (X11), GPE and QT4-Embedded


M-606:General• OS: Windows CE 6.0• RAM-based File System: Up to 94MB free space available• NAND-based File System: Up to 200MB free space available

Ready-to-use Network Services• Web Server: Supports ASP• Telnet Server• FTP Server

Application Development & Deployment• Development: It is recommended to use Microsoft Visual Studio 2005 for application development. The M-606 comes with its own SDK for C / C++ programming language.• Deployment: The application program can be transferred to the M-606 either by ActiveSync or USB pen drive locally or by FTP remotely.

M-5360A

Features

• M-5360A i.MX537 Cortex A8 System on Module

H/W Specifications


S/W Specifications

• ATMEL 400MHz AT91SAM9G45 CPU w/ MMU• Linux kernel 2.6.38 with file system (M-506) Windows CE 6.0 with file system (M-606)• 128MB SDRAM and 256MB NAND Flash• 2MB DataFlash for system recovery• On-board real-time clock w/ backup battery• Supports up to 1280 x 860 LCD and touch screen• Supports LVDS• 1 x 10/100Mbps Ethernet• 3 x RS-232 ports, 1 x RS-422 / 485 port• 4 x USB 2.0 hosts supporting high speed of 480Mbps

Features

• M-506 Linux-based ARM9 Single Board Computer

• M-606 WinCE 6.0 ARM9 Single Board Computer

Linux / WinCE 6.0 ARM9 Single Board ComputerM-506 / M-606

Function Block

USB Host UART 2/3 (four pins)

UART 4 (two pins)

1-wire

USB OTG

UART 1 (full)

GPIO

10/100Mbps

RMIII2C Touch

LVDS 0

LVDS 1

Brightness

I2C

I2S

VGA Out (Syn. LVDS 0)

DDR3 eMMC

CAN

SATA

SD SPI

Batte

ry

i.MX537Ethernet

PHY PMIC

CN1

CN2

BootS/W

CN3

DDR3 SDRAM

DDR3 SDRAM

PMIC

CPU

CN3

Front View

Rear VieweMMC

DDR3 SDRAM

DDR3 SDRAM

CN2

CN1

COM 3/4(RS-232) LCD (TTL)

USB Client

LCD Controls

12~40VDCPower Input

COM 2(RS-485 / 422)DI x 2 / DO x 2

USB Host

Console Touch ScreenLCD (LVDS)

microSD

LANCOM 1(RS-232)

Audio Out

128MB Flash

128MB SDRAM


Linux-ready ARM9 Single Board Computer

H/W Specifications


S/W Specifications

• Linux 2.6.14 compatible computing platform• 64MB SDRAM and 32MB NOR Flash• Ultra-low power consumption, less than 3 Watts• 1 x 10/100Mbps Ethernet port• 4 x 921.6Kbps RS-232 / 485 TTY ports• 2 x USB 2.0 host ports for functionality expansion• 1 x SD memory card slot inside for storage expansion• 32 x CMOS-level digital I/Os (GPIO)• Single 5V power input• GNU C / C++ toolchain for Linux / Windows environment

CPU / Memory• CPU: ATMEL 180MHz AT91RM9200 (ARM9, w/ MMU)• Memory: 64MB SDRAM, 32MB NOR Flash• SRAM: 512KB, non-volatile (M-508T only)


TTY (Serial) Ports• 4 x RS-232 / 485 ports, software select• Port 2: Supports full modem signals• Port 4: Also supports RS-422 mode• Connector: 10-pin header, male

TTY (Serial) Port Parameters• Baud Rate: Up to 921.6 Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None

USB Ports• Host Ports: 2, USB 2.0 compliant• Speed: Supports low-speed (1.5Mbps) and full-speed (12Mbps) data rate

CMOS-level Digital I/Os (GPIO)• No. of Pins: 32• Each pin can be programmed as input or output

Mass Storage• 1 x SD 1.0 compliant socket

General• Watchdog Timer: Yes, for kernel use• Real Time Clock: Yes• Buzzer: Yes• Power Input: +5VDC, 600mA typical• Board Dimensions (W x H): 105 x 75mm• Operating Temperature: - M-508: 0~70ºC (32~158ºF) - M-508T: -20~80ºC (-4~176ºF)



Utilities• bash: shell command• tinylogin: login and user manager utility• telnet: telnet client program• busybox: Linux utility collection• ftp: ftp client program





M-508

Features

• M-508 Linux-ready ARM9 Single Board Computer with 32MB NOR Flash, 64MB SDRAM• M-508T Wide-temperature Linux-ready ARM9 Single Board Computer with 32MB NOR Flash, 64MB SDRAM, 512KB non-volatile SRAM

TTY PIN Assignment

*: Port 2 only**: Port 4 only

PIN RS-232 RS-422 RS-48512345678910

DCDDSRRx

RTSTx

CTSDTR---

GND---

Tx----Tx+---

Rx+---Rx----

GND---

------------

Data+---

Data----

GND---

* *

*

* * 2 10

1 9

+5V Input32MBFlash

GPIO 16~31Ethernet

RS-232RS-422RS-485

ATMELARM9

64MBSDRAM

GPIO 0~15USB Host x 2

Reset

RS-232RS-485

RS-232RS-485

RS-232RS-485

www.artila.com www.artila.com29

www.artila.com29 30

Programmable Automation Controller

• ARM+Linuxcomputingplatform

• 2500Vrmsisolationprotection

• IndustrialisolateddigitalandanalogI/O

• DualEthernetandisolatedRS-485

• DINRAILmounted

Features

PAC Series Selection GuideModel PAC-4000 PAC-4010 PAC-4070 PAC-5010 PAC-5070

CPU ATMEL AT91SAM9G20 ARM926 400MHz ATMEL AT91RM9200 ARM920 180MHz

RAM 64MB SDRAM

Flash 256MB NAND 16MB NOR

RTC Yes

Watchdog Timer Yes

Battery Li 48mAh SuperCap

No. of Serial Port 4* 4* 4* 2 2

• RS-232 4 4 4 1 1

• RS-422 N/A N/A N/A N/A N/A

• RS-485 2 isolated 2 isolated 2 isolated 1 1

Ethernet 10/100Mbps x 2

USB Host Full speed x 2

USB Client Full speed x 1

SD microSD x 1 SD x 1

Isolated DIO Channels N/A 16 8 24 16

• Isolated Input (2500Vrms) N/A 8 4 16 8

• Isolated Output (500mA) N/A 8 4 N/A N/A

• High-Drive Output (500mA) N/A N/A N/A 8 8

Isolated A/D Channels N/A N/A 4 N/A 4

• Isolated N/A N/A 2500Vrms N/A 2500Vrms

• Resolution N/A N/A 16-bit N/A 16-bit

• Input Range N/A N/A V, mV, 0~20mA N/A V, mV, 0~20mA

• Sampling Rate N/A N/A 10 samples/s N/A 10 samples/s

Power 9~40VDC

Linux 2.6.29 2.6.14

Enclosure Sheet Metal N/A

DIN RAIL Kit Aluminum Bracket Plastic

500mA High-DriveDigital Output

2500VrmsOpto-isolation Digital Input

2500Vrms Isolation

16-bit A/D ConverterDiff. input, mV, V, 0~20mA

*: Port 1, 2: can be set as RS-232 or isolated RS-485Port 3, 4: for RS-232 only

Linux-based ARM9 Programmable Automation Controller

H/W Specifications


S/W Specifications

• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• 2MB DataFlash for system recovery• On-board real-time clock• 2 x 10/100Mbps Ethernet ports• Up to 4 x RS-232 ports, 921.6Kbps max.• 2 x 2500Vrms isolated RS-485 ports, with auto direction control• 2 x USB 2.0 Hosts supporting full speed of 12Mbps• Small form factor (W x H x D): 45 x 130 x 102.5mm


Network Interface• No. of Ports: 2• Type: 10/100Mbps Ethernet, RJ45 connector• Protection: 1.5KV magnetic isolation

Serial Ports• 2 x RS-485 or RS-232 (Port 1 and Port 2)• 2 x RS-232 (Port 3 and Port 4)• Protection: 15KV ESD for RS-232; 2500Vrms isolation and 15KV ESD for RS-485• Connector: RJ45 for RS-232; Terminal Block for RS-485

Serial Port Parameters• Baud Rate: Up to 921.6Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2• Flow Control: RTS / CTS, XON / XOFF, None• RS-485 Direction Control: Auto, by hardware

USB Ports• Host Ports: 2, USB 2.0 compliant• Client Port: 1, reserved• Speed: Supports low-speed (1.5Mbps) and full-speed (12Mbps)

SD Socket (Secure Digital Card)• Type: microSD• No. of Sockets: 1, at the bottom side

General• Watchdog Timer: Yes• Real Time Clock: Yes, with backup battery• Buzzer: Yes• Power Input: 9~40VDC• Power Consumption: 300mA@12VDC• Dimensions (W x H x D): 45 x 130 x 102.5mm• Operating Temperature: 0~70ºC (32~158ºF)• Regulation: CE Class A, FCC Class A

General• OS: Linux, kernel 2.6.29• Boot Loader: U-Boot 1.1.2• File Systems: UBI, JFFS2, ETX2 / ETX3, VFAT / FAT, NFS• Internet Protocol: TCP, UDP, IPv4, SNMP V1 / V2 / V3, ICMP, ARP, HTTP, CHAP, PAP, DHCP, NTP, NFS, SMTP, TELNET, FTP, TFTP, PPP, PPPoE• Internet Security: OpenVPN, iptables

Pre-installed Utilities• bash, busybox, sysvinit, wget, ipkg, procps (for webmin), psmics, lighttpd, vsftpd, iptables, ppp, ssh, wireless_tools, util-linux-mount / umount, usbutils, Artila utility and more


Package Management & System Administration• Supports ipkg to manage the package installation, upgrade and removal• Supports webmin for web-based system administration


USB Host Drivers• Generic Flash drive• RS-232 adapters (for Prolific PL-2303 compatibles)• WiFi dongles (for Ralink RT73 compatibles and more)

CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G20 w/ MMU• Memory: 64MB SDRAM, 256MB NAND Flash • DataFlash®: 2MB, for system backup






Isolated Digital Input• No. of Channels: 8• Logical High: 5~24VDC; Logical Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20µs• Opto-isolation: 2500Vrms

Digital Output• No. of Channels: 8• Source Driver: UDN2981A (Allegro MicroSystems)• Source Voltage (VDD): 5~50VDC• Output Current: 500mA max.• Isolation: 2500Vrms








PAC-4000

Features

• PAC-4000 Linux-based ARM9 Programmable Automation Controller




H/W Specifications


S/W Specifications

• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• 2MB DataFlash for system recovery• 2 x 10/100Mbps Ethernet ports• Up to 4 x RS-232 ports, 921.6Kbps max.• 2 x 2500Vrms isolated RS-485 ports, with auto direction control• 2 x USB 2.0 Hosts supporting full speed of 12Mbps• 8 x 2500Vrms opto-isolated digital inputs• 8 x 500mA max. High-Drive digital outputs• Small form factor (W x H x D): 65 x 130 x 102.5mm

Features





Linux-based ARM9 Programmable Automation ControllerPAC-4010

130m

m

LED Indicator

2 x LANs

2 x USB Hosts

2 x RS-232 Ports

2 x RS-232 Ports

1 x USB Client

2 x RS-485 Ports

8 x Digital Inputs

8 x Digital Outputs

9~40VDC Power Input

1 x microSD socket at the bottom side

130m

m

LED Indicator

2 x LANs

2 x USB Hosts

2 x RS-232 Ports

2 x RS-232 Ports

1 x USB Client

2 x RS-485 Ports

9~40VDC Power Input




H/W Specifications


S/W Specifications

• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• 2MB DataFlash for system recovery• On-board real-time clock• 2 x 10/100Mbps Ethernet ports• Up to 4 x RS-232 ports, 921.6Kbps max.• 2 x 2500Vrms isolated RS-485 ports, with auto direction control• 2 x USB 2.0 Hosts supporting full speed of 12Mbps• Small form factor (W x H x D): 45 x 130 x 102.5mm














CPU / Memory• CPU: ATMEL 400MHz AT91SAM9G20 w/ MMU• Memory: 64MB SDRAM, 256MB NAND Flash • DataFlash®: 2MB, for system backup






Isolated Digital Input• No. of Channels: 8• Logical High: 5~24VDC; Logical Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20µs• Opto-isolation: 2500Vrms

Digital Output• No. of Channels: 8• Source Driver: UDN2981A (Allegro MicroSystems)• Source Voltage (VDD): 5~50VDC• Output Current: 500mA max.• Isolation: 2500Vrms








PAC-4000

Features





H/W Specifications


S/W Specifications

• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• 2MB DataFlash for system recovery• 2 x 10/100Mbps Ethernet ports• Up to 4 x RS-232 ports, 921.6Kbps max.• 2 x 2500Vrms isolated RS-485 ports, with auto direction control• 2 x USB 2.0 Hosts supporting full speed of 12Mbps• 8 x 2500Vrms opto-isolated digital inputs• 8 x 500mA max. High-Drive digital outputs• Small form factor (W x H x D): 65 x 130 x 102.5mm

Features






130m

mLED Indicator

2 x LANs

2 x USB Hosts

2 x RS-232 Ports

2 x RS-232 Ports

1 x USB Client

2 x RS-485 Ports

8 x Digital Inputs

8 x Digital Outputs

9~40VDC Power Input


130m

m

LED Indicator

2 x LANs

2 x USB Hosts

2 x RS-232 Ports

2 x RS-232 Ports

1 x USB Client

2 x RS-485 Ports

9~40VDC Power Input




H/W Specifications


• ATMEL 400MHz AT91SAM9G20 CPU w/ MMU• Linux kernel 2.6.29 with file system• 64MB SDRAM and 256MB NAND Flash• GNU C / C++ toolchain is included• 4 x 16-bit multiplexed differential analog inputs• 4 x 2500Vrms 500mA High-Drive digital outputs• 4 x 2500Vrms Opto-isolated bipolar digital inputs• 2 x 10/100Mbps Ethernet ports• Up to 4 x RS-232 ports, 921.6Kbps max.• 2 x 2500Vrms isolated RS-485 ports, with auto direction control



TTY (Serial) Ports• Port 1: Can be set as RS-232 or RS-485, software selectable RS-232: TX, RX, RTS, CTS, GND RS-485: D+, D- (must wiring to terminal block)• Port 2: Can be set as RS-232 or RS-485, software selectable RS-232: TX, RX, RTS, CTS, DSR, DTR, DCD, GND RS-485: D+, D- (must wiring to terminal block)• Port 3, 4: RS-232 only RS-232: TX, RX, RTS, CTS, GND


USB Ports• Host Ports: 2, USB 2.0 compliant• Client Port: 1, USB 2.0 compliant• Speed: Supports 12Mbps full-speed mode

SD Socket (Secure Digital Card)• Type: microSD• No. of Sockets: 1, at the bottom side• Storage Capacity: Up to 32GB• Compatibility: SD memory card specification 1.0

Real Time Clock• Chip: ST M41T81• Backup Battery: Lithium, 48mAh, on-board

Watchdog Timer• CPU built-in watchdog timer, used by Linux kernel

Debug Port• Type: RS-232 serial console, inside the box• Signals: Tx, Rx, GND

High-precision Analog Input• A/D Converter: AD7712 (Analog Devices)• No. of Channels: 4, multiplexed, differential• Sampling Speed: 10 readings per second• Input Range (selected by software): 0~150mV, 0~500mV, +/-150mV, +/-500mV 0~1V, 0~5V, 0~10V, +/-1V, +/-5V, +/-10V 0~20mA• Resolution: 16-bit• Accuracy: +/-1%• Voltage Input Mode: Differential, 100db CMR• Voltage Input Impedance: 20M Ohms• Current Input Impedance: 120 Ohms• Isolation Protection: 1500VDC

Isolated Digital Input• No. of Channels: 4, supporting bipolar input• Opto-isolation: 2500Vrms• Logical High: 5~24VDC• Logical Low: 0~1.5VDC• Response Time: 20µs• Input Resistance: 1.2k [email protected]

High-Drive Digital Output• No. of Channels: 4• Source Driver: UDN2981A (Allegro MicroSystems)• Source Voltage (VDD): 5~50VDC• Output Current: 500mA max.• Isolation: 2500Vrms

General• Power Input Range: 9~40VDC• Power Consumption: 500mA@12VDC, 6 Watts max.• Operating Temperature: 0~70°C (32~158°F)• EMC Regulation: CE Class A, FCC Class A• Dimensions (W x H x D): 65 x 130 x 102.5mm• Mounting: DIN RAIL mountable


Network Interface• Type: 2 x 10/100BaseT, RJ45 connector

TTY (Serial) Ports• RS-485: One port, with screw-fixed wiring terminal Signals: Data+, Data-, GND• RS-232: One port, with 10-pin header Signals: Tx, Rx, RTS, CTS, DSR, DTR, DCD, GND• Console: One port, with 10-pin header Signals: Tx, Rx, GND


USB Ports• Host Ports: 2, USB 2.0 compliant, with 10-pin header• Data Rate: Up to 12Mbps


Isolated Digital Input• No. of Channels: 16• Logical High: 5~24VDC• Logical Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20µs• Opto-isolation: 2500Vrms

Digital Output• No. of Channels: 8• Source Driver: UDN2981A (Allegro MicroSystems)• Source Voltage (VDD): 5~50VDC• Output Current: 500mA max.









PAC-4070

Features

• PAC-4070 Linux-based ARM9 Programmable Automation Controller• 91-R45F9-150 Serial Cable (RJ45 to DB9 Female, 150cm)• 91-PHDF9-050 Console Cable (Wafer Box to DB9 Female, 50cm)• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter

H/W Specifications S/W Specifications

• Linux kernel 2.6.14 OS with file system• 64MB SDRAM and 16MB NOR Flash• 16 x opto-isolated digital inputs• 8 x Darlington-pair digital outputs to drive external relays• 2 x 10/100Mbps Ethernet ports• 1 x RS-232 port, 1 x RS-485 port• 2 x USB 2.0 host ports for add-on functionality expansion• 1 x SD memory card slot included for storage expansion• GNU C / C++ toolchain for Linux / Windows environment• 9~40VDC input range

Features





9~40VDC Input

DualEthernet

DualUSB Hosts 8 x Digital Outputs

16 x Opto-isolatedDigital Inputs

RS-485

ConsoleRS-232

130m

m LED Indicator

2 x LANs

2 x USB Hosts

2 x RS-232 Ports

2 x RS-485 Ports

9~40VDC Power Input

4 x 16-bit Differential Analog Inputs

2 x RS-232 Ports

1 x Isolated Digital Input

3 x Isolated Digital Inputs

4 x High-Drive Digital Outputs




H/W Specifications


• Linux kernel 2.6.14 OS with file system• 64MB SDRAM and 16MB NOR Flash• 4 x 16-bit high-precision multiplexed analog inputs• 8 x 2500Vrms opto-isolated digital inputs• 8 x 500mA High-Drive digital outputs• 2 x 10/100Mbps Ethernet ports• 1 x RS-232 port, 1 x RS-485 port• 2 x USB 2.0 host ports for add-on functionality expansion• 1 x SD memory card slot included for storage expansion• GNU C / C++ toolchain for Linux / Windows environment• 9~40VDC input range


Network Interface• Type: 2 x 10/100BaseT, RJ45 connector

TTY (Serial) Ports• RS-485: One port, with screw-fixed wiring terminal Signals: Data+, Data-, GND• RS-232: One port, with 10-pin header Signals: Tx, Rx, RTS, CTS, DSR, DTR, DCD, GND• Console: One port, with 10-pin header Signals: Tx, Rx, GND


USB Ports• Host Ports: 2, USB 2.0 compliant, with 10-pin header• Data Rate: Up to 12Mbps


Isolated Digital Input• No. of Channels: 8• Logical High: 5~24VDC• Logical Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20µs• Opto-isolation: 2500Vrms

Digital Output• No. of Channels: 8• Source Driver: UDN2981A (Allegro MicroSystems)• Source Voltage (VDD): 5~50VDC• Output Current: 500mA max.









PAC-5070

Features



S/W Specifications

9~40VDC Input

DualEthernet

DualUSB Hosts 8 x Digital Outputs

4 x AnalogInputs

RS-485

ConsoleRS-232 8 x DigitalInputs


www.artila.com35 36

Web-based Remote I/O

Stand-alone Operation TheRIOseriescanbeprogrammedasastand-alonecontrollerbyusingtheFreeRTOSSDK.OncethefirmwareisdownloadedtotheRIO,itcanperformthetaskwithoutusing a host computer. Several pre-programmed applications firmwareareavailableforuserstodownloadtoRIO.

Web Control Inwebcontrolmode,RIOcanbecontrolledbywebbrowser.UsercaneditawebpageanddownloadittoRIO.ThewebpagecanuseAJAXtechniquetoaccesstheRIO.

Modbus Control IntheModbusmode,RIOsupportsModbusprotocolandit can be controlled by any hardware and software which support Modbus. In addition, Windows and Linux API library are availableforprogrammerstoeasilyaccessRIO.

Features• RemoteindustrialI/Owithwebinterface(AJAX)�

• Supportstand-alone,webcontrolandModbusTCP/RTU

• Basedon32-bitARMCortexMcontrollerandFreeRTOS

• WindowsandLinuxC/C++APIavailable

• FreeRTOSSoftwareDevelopmentKit(SDK)�isavailable for customized firmware

Who We Are

Modbus / TCP Remote Digital I/O Module

H/W Specifications


Access Control Guidelines

• Web based remote I/O monitoring and control

• Web server and web interface ready

• Modbus, AJAX, MQTT

• Stand-alone alarm relay control and email alert

• Periodically data and event publishing to server (broker) via MQTT

• Form A or form B relay with contact rating 30VDC@1A or [email protected]

• 16 isolated digital input and 1-wire temperature measurement

Network Interface• Type: 1 x 10/100Mbps, RJ45 connector • Protection: 1.5KV magnetic isolation

RS-485 Interface• Isolation Protection: 2500Vrms• Direction Control: Auto, by hardware• Connector: Terminal block• Baud Rate: 1.2~460.8Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2

Digital Input• No. of Channels: 16• Isolation Protection: 2500Vrms• Logical High: 5~24VDC• Logical Low: 0~1.5VDC• LED Indicators: Yes

Relay Output• No. of Channels: 8• Contact Rating: 30VDC@1A or [email protected]• LED Indicators: Yes

Maxim 1-Wire Interface• No. of Channels: 3• Connector: 3-pin header (VDD, DQ, GND)

General• CPU: 32-bit, Cortex M3 series• Temperature Sensor: Maxim DS18B20 (optional accessary 30-6DS18-001)• Temperature Range: -55°C~125°C• Accuracy: +/-0.5°C• Real Time Clock: Manual or NTP (Network Time Protocol) setup and sync.• Power Input: 9~48VDC• Power Consumption: 220mA@12VDC max. and 55mA@12VDC min. • Dimensions (W x H x D): 182 x 118 x 35.82mm• Operating Temperature: 0~70°C• Storage Temperature: -20~85°C

Default Access Ports• Modbus / TCP Port: 502• Telnet Console Port: 5001• HTTP Port: 5003

Access Through Modbus Protocols• Modbus / TCP via LAN interface• Modbus / ASCII, Modbus / RTU via RS-485 interface

Access Through HTTP GET / POST Protocols• AJAX-enabled demo page for up-and-running web-based monitoring and controls

Operation Mode• Modbus TCP / RTU slave• Web direct I/O control• MQTT auto data and event publish and log• Stand-alone alarm relay control and email alert• C / C++ programmable controller (RIO-2010PG)

Network Interface• Type: 1 x 10/100Mbps, RJ45 connector• Protection: 1.5KV Magnetic isolation• Protocol: Modbus / TCP, UDP, HTTP, DHCP

Isolation Analog Input• No. of Channels: 8• Input Type: Differential input• Input Mode: Voltage / Current • Resolution: 16-bit• Input Range: Unipolar: 0~150mV, 0~500mV, 0~1V, 0~5V, 0~10V Bipolar: +/-150mV, +/-500mV, +/-1V, +/- 5V, +/-10V Current: 0~20mA• Input Impedance: 20M Ohm (voltage), 120 Ohm (current)• Accuracy: +/-1% FSR• Isolation: 1500VDC

Relay Output• No. of Channels: 1• Contact Rating: 30VDC@1A or [email protected]

Mechanical• Power: 9~48VDC terminal block• Protection: Auto polarity and surge protect• Dimensions (W x H x D): 78 x 108 x 25mm

RIO-2010

Features

• RIO-2010 Modbus / TCP Remote Digital I/O Module


• 30-6DS18-001 (DS18B20) Programmable Resolution 1-wire Digital Thermometer


H/W Specifications


• Remote analog input module with web access AJAX and Modbus / TCP• 1 x 10/100Mbps Ethernet port• 8 x 16-bit A/D• Isolation up to 2500Vrms• 1 x relay output• Form A or Form B relay with contact rating 30VDC@1A or [email protected]• Support web-based I/O control• Optional DIN RAIL mounting kit (DK-35A)• Windows configuration utility included

Features

• RIO-2017 Analog Input Remote I/O Module• DK-35A DIN RAIL Mounting Kit• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter • Software Utility Download from Artila web

Analog Input Remote I/O ModuleRIO-2017

LAN

9~48VDCPower In

RelayOutput

A/ICH7~8

A/I CH1~6

Access Control GuidelinesDefault Access Ports• Modbus / TCP Port: 502• Telnet Console Port: 5001• HTTP Port: 5003



Windows Utility Functionalities• Broadcast search• Configuration• User web page conversion


Front View

Power In

Ethernet 1-Wire Relay Output(NO or NC Jumper)

Isolated Digital Input

RS-485

ConsoleRS-232

Modbus / TCP Remote Digital I/O Module

H/W Specifications


Access Control Guidelines

• 16 x opto-isolated digital inputs

• 8 x relay outputs

• 3 x Maxim 1-Wire interface

• 1 x 10/100Mbps Ethernet interface

• 1 x isolated RS-485 interface

• Supports Modbus / TCP, Modbus RTU / ASCII

• Ready-to-use web-based control & monitor

• DIN RAIL mount

Network Interface• Type: 1 x 10/100Mbps, RJ45 connector • Protection: 1.5KV magnetic isolation

RS-485 Interface• Isolation Protection: 2500Vrms• Direction Control: Auto, by hardware• Connector: Terminal block• Baud Rate: 1.2~460.8Kbps• Parity: None, Even, Odd, Mark, Space• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 1.5, 2

Digital Input• No. of Channels: 16• Isolation Protection: 2500Vrms• Logical High: 5~24VDC• Logical Low: 0~1.5VDC• LED Indicators: Yes

Relay Output• No. of Channels: 8• Contact Rating: 30VDC@1A or [email protected]• LED Indicators: Yes

Maxim 1-Wire Interface• No. of Channels: 3• Connector: 3-pin header (VDD, DQ, GND)

General• CPU: 32-bit, Cortex M3 series• Power Input: 9~48VDC• Dimensions (W x H x D): 182 x 118 x 35.82mm• Operating Temperature: 0~70°C

Default Access Ports• Modbus / TCP Port: 502• Telnet Console Port: 5001• HTTP Port: 5003




Network Interface• Type: 1 x 10/100Mbps, RJ45 connector• Protection: 1.5KV Magnetic isolation• Protocol: Modbus / TCP, UDP, HTTP, DHCP

Isolation Analog Input• No. of Channels: 8• Input Type: Differential input• Input Mode: Voltage / Current • Resolution: 16-bit• Input Range: Unipolar: 0~150mV, 0~500mV, 0~1V, 0~5V, 0~10V Bipolar: +/-150mV, +/-500mV, +/-1V, +/- 5V, +/-10V Current: 0~20mA• Input Impedance: 20M Ohm (voltage), 120 Ohm (current)• Accuracy: +/-1% FSR• Isolation: 1500VDC

Relay Output• No. of Channels: 1• Contact Rating: 30VDC@1A or [email protected]


RIO-2010

Features

• RIO-2010 Modbus / TCP Remote Digital I/O Module


H/W Specifications


• Remote analog input module with web access AJAX and Modbus / TCP• 1 x 10/100Mbps Ethernet port• 8 x 16-bit A/D• Isolation up to 2500Vrms• 1 x relay output• Form A or Form B relay with contact rating 30VDC@1A or [email protected]• Support web-based I/O control• Optional DIN RAIL mounting kit (DK-35A)• Windows configuration utility included

Features


Analog Input Remote I/O ModuleRIO-2017

LAN

9~48VDCPower In

RelayOutput

A/ICH7~8

A/I CH1~6

Access Control GuidelinesDefault Access Ports• Modbus / TCP Port: 502• Telnet Console Port: 5001• HTTP Port: 5003





Front View

Analog Input Remote I/O Module

H/W Specifications


• Remote thermocouple input module with web access AJAX and Modbus / TCP• 1 x 10/100Mbps Ethernet port• 3 channels J or K type thermocouple input with cold junction compensation• 2 x 2500Vrms isolated digital input (bipolar input photocoupler)• 1 x Form C relay with contact rating 30VDC@1A or [email protected]• Support web-based temperature monitoring and DIO control• Optional DIN RAIL mounting kit (DK-35A)• Windows configuration utility included

Network Interface• Type: 1 x 10/100Mbps Ethernet, RJ45 connector• Protection: 1.5KV magnetic isolation• Protocol: Modbus / TCP, UDP, HTTP, DHCP

Thermocouple Input• J type: Maxim MAX31855J converter with CJC Range: -210°C~+1200°C• K type: Maxim MAX31855K converter with CJC Range: 200°C~+1350°C• Resolution: 14-bit, 0.25°C• Connector: OMEGA PCC-SMP Thermocouple connector Thermocouple fault detection

Relay Output• No. of Channels: 1 x Form C• Contact Rating: 30VDC@1A or [email protected]

Isolated Digital Input• No. of Channels: 2• Logic High: 5~24VDC• Logic Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20μs


Network Interface• Type: 1 x 10/100BaseT, RJ45 connector• Protocols: TCP, UDP, HTTP, TELNET, IP, ICMP, ARP• IP addressing: DHCP, Static IP

Operation Modes• TCP / Server and TCP / Client

Serial Interface• Type: RS-232 / 422 / 485, switch selectable• Connector: DB9, male• Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND• Baud Rate: 1.2~38.4Kbps• Parity: None, Even, Odd• Data Bits: 7, 8• Stop Bits: 1, 2• Flow Control: None, RTS / CTS, XON / OFF

Programmable Digital I/Os• PIO0~PIO5: TTL level compatible• PIO6~PIO7: CMOS level compatible• Connector: DB9, male

Configuration Methods• Web console, Telnet Console and Serial Console

General• Power Input: 9~40VDC• Power Consumption: 70mA@+12VDC• Operating Temperature: 0~70°C, 5~95% RH• Storage Temperature: -20~85°C, 5~95% RH• Dimensions (W x H x D): 78 x 108 x 25mm• Weight: 300g• Regulation: CE / FCC compliant• Warranty: 5 years

RIO-2018

Features

• RIO-2018 Analog Input Remote I/O Module• 91-5SRTC-J50 (5SRTC-GG-J-24-36) Standard Size Connector, J Thermocouple, Glass Braid Insulation, 24 AWG, 36 inch Length, 5 PACK• 91-5SRTC-K50 (5SRTC-GG-K-24-36) Subminiature Connector, K Thermocouple, Glass Braid Insulation, 24 AWG, 36 inch Length, 5 PACK• DK-35A DIN RAIL Mounting Kit• PWR-12V-1A 110~240VAC to 12VDC 1A Power Adapter • Software Utility Download from Artila web

H/W Specifications


• Connect RS-232 / 422 / 485 devices to TCP/IP network

• 8 x programmable digital I/Os

• 10/100Mbps Ethernet; 38.4Kbps serial data rate

• Supports TCP / Server mode and TCP / Client mode

• Web / Telnet / Serial consoles for device configuration

• Windows utility for device configuration and management

• Firmware upgradable

Features

• Aport-211S Single-port Serial-to-Ethernet Gateway



Single-port Serial-to-Ethernet GatewayAport-211S

PIN GPIO123456789

PIO 0PIO IPIO 2PIO 3PIO 4PIO 5PIO 6PIO 7GND

PIN AssignmentPIN RS-232

123456789

DCDRxTx

DTRGNDDSRRTSCTS---

Tx-Tx+Rx+Rx-

GND------------

RS-422 RS-485------


LAN

9~48VDCPower In

RelayOutput

Digital InDI1 / DI2

ThermocoupleT/C1~T/C3

OMEGA PCC-SMP

1

6 7 8 9

2 3 4 5 1

6 7 8 9

2 3 4 5

MAX31855

ADC

DIGITALCONTROL

COLD-JUNCTIONCOMPENSATION

FAULTDETECTION

REFERENCEVOLTAGE

S4

S1

S2

S3

S5 SCK

VCC

SO

CS

GND

T+

T-

VCC

Thermocouple InputThe thermocouple input is connected to MAX31855 Cold Junction Compensated Thermocouple to Digital Converter. The connector is OMEGA PCC-SMP. Please make sure the type of thermocouple matches the model of RIO-2018. Please refer to datasheet of MAX31855 for the technical specification of thermocouple measurement.

Thermocouple ConnectorGMP & HGMP

unit: mm (inches)

2.54 DIA.(0.1)

4.7(0.18)

0.8(0.03)

3.17(0.13)

8(0.31)

8(0.31)

2.4(0.09)

3.17(0.13)

12.7(0.5)

8(0.31)

32(1.25)

37(1.44)

51.5(2.03)

7(0.28)

8(0.31)

FEMALEMALE

Dimensions

Ø4

Ø7

77.5mm

89.0mm

25.0

mm

43.0

mm

108.

0mm


Front View

Analog Input Remote I/O Module

H/W Specifications


• Remote thermocouple input module with web access AJAX and Modbus / TCP• 1 x 10/100Mbps Ethernet port• 3 channels J or K type thermocouple input with cold junction compensation• 2 x 2500Vrms isolated digital input (bipolar input photocoupler)• 1 x Form C relay with contact rating 30VDC@1A or [email protected]• Support web-based temperature monitoring and DIO control• Optional DIN RAIL mounting kit (DK-35A)• Windows configuration utility included

Network Interface• Type: 1 x 10/100Mbps Ethernet, RJ45 connector• Protection: 1.5KV magnetic isolation• Protocol: Modbus / TCP, UDP, HTTP, DHCP

Thermocouple Input• J type: Maxim MAX31855J converter with CJC Range: -210°C~+1200°C• K type: Maxim MAX31855K converter with CJC Range: 200°C~+1350°C• Resolution: 14-bit, 0.25°C• Connector: OMEGA PCC-SMP Thermocouple connector Thermocouple fault detection

Relay Output• No. of Channels: 1 x Form C• Contact Rating: 30VDC@1A or [email protected]

Isolated Digital Input• No. of Channels: 2• Logic High: 5~24VDC• Logic Low: 0~1.5VDC• Input Resistance: 1.2K [email protected]• Response Time: 20μs


Network Interface• Type: 1 x 10/100BaseT, RJ45 connector• Protocols: TCP, UDP, HTTP, TELNET, IP, ICMP, ARP• IP addressing: DHCP, Static IP

Operation Modes• TCP / Server and TCP / Client

Serial Interface• Type: RS-232 / 422 / 485, switch selectable• Connector: DB9, male• Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND• Baud Rate: 1.2~38.4Kbps• Parity: None, Even, Odd• Data Bits: 7, 8• Stop Bits: 1, 2• Flow Control: None, RTS / CTS, XON / OFF

Programmable Digital I/Os• PIO0~PIO5: TTL level compatible• PIO6~PIO7: CMOS level compatible• Connector: DB9, male

Configuration Methods• Web console, Telnet Console and Serial Console

General• Power Input: 9~40VDC• Power Consumption: 70mA@+12VDC• Operating Temperature: 0~70°C, 5~95% RH• Storage Temperature: -20~85°C, 5~95% RH• Dimensions (W x H x D): 78 x 108 x 25mm• Weight: 300g• Regulation: CE / FCC compliant• Warranty: 5 years

RIO-2018

Features


H/W Specifications


• Connect RS-232 / 422 / 485 devices to TCP/IP network

• 8 x programmable digital I/Os

• 10/100Mbps Ethernet; 38.4Kbps serial data rate

• Supports TCP / Server mode and TCP / Client mode

• Web / Telnet / Serial consoles for device configuration

• Windows utility for device configuration and management

• Firmware upgradable

Features

• Aport-211S Single-port Serial-to-Ethernet Gateway



Single-port Serial-to-Ethernet GatewayAport-211S

PIN GPIO123456789

PIO 0PIO IPIO 2PIO 3PIO 4PIO 5PIO 6PIO 7GND

PIN AssignmentPIN RS-232

123456789

DCDRxTx

DTRGNDDSRRTSCTS---

Tx-Tx+Rx+Rx-

GND------------

RS-422 RS-485------


LAN

9~48VDCPower In

RelayOutput

Digital InDI1 / DI2

ThermocoupleT/C1~T/C3

OMEGA PCC-SMP

1

6 7 8 9

2 3 4 5 1

6 7 8 9

2 3 4 5

MAX31855

ADC

DIGITALCONTROL

COLD-JUNCTIONCOMPENSATION

FAULTDETECTION

REFERENCEVOLTAGE

S4

S1

S2

S3

S5 SCK

VCC

SO

CS

GND

T+

T-

VCC

Thermocouple InputThe thermocouple input is connected to MAX31855 Cold Junction Compensated Thermocouple to Digital Converter. The connector is OMEGA PCC-SMP. Please make sure the type of thermocouple matches the model of RIO-2018. Please refer to datasheet of MAX31855 for the technical specification of thermocouple measurement.

Thermocouple Connector

GMP & HGMP

unit: mm (inches)

2.54 DIA.(0.1)

4.7(0.18)

0.8(0.03)

3.17(0.13)

8(0.31)

8(0.31)

2.4(0.09)

3.17(0.13)

12.7(0.5)

8(0.31)

32(1.25)

37(1.44)

51.5(2.03)

7(0.28)

8(0.31)

FEMALEMALE

Dimensions

Ø4

Ø7

77.5mm

89.0mm

25.0

mm

43.0

mm

108.

0mm


Front View

Dual-port Modbus Gateway

H/W Specifications


• Gateway of Modbus / TCP to Modbus RTU / ASCII• 2 x configurable RS-232 / 485 serial ports• Supports up to 16 x Modbus / TCP masters or 32 x Modbus / TCP slaves• Supports transparent serial to Ethernet conversion• 1 x 10/100Mbps Ethernet port• Supports telnet, web and serial console configuration• Support command line interface configuration• Windows configuration utility included• Firmware upgradable by Ethernet / Internet

CPU / Memory• CPU: 32-bit ARM SoC


Serial Ports• Port 1: RS-232 / 422 / 485• Port 2: RS-232 / 485

Serial Port Parameters• Baud Rate: 1.2~921.6Kbps• Data Bits: 5, 6, 7, 8• Stop Bits: 1, 2• Flow Control: None / Hardware / XON_XOFF• Protection: 15KV ESD


Operation Mode• Modbus Gateway: Slave RTU, Slave ASCII, Master RTU, Master ASCII• S2E Gateway: TCP server, TCP client

General• Power Input: 9~40VDC power jack and terminal block• Dimensions (W x H x D): 78 x 108 x 25mm• Operating Temperature: 0~60ºC• Storage Temperature: -20~85ºC

Aport-212

Features

• Aport-212 Modbus Gateway with 2 x Serial Ports, and 1 x Ethernet Port




Modbus / TCPSlave Devices

Modbus RTU / ASCII Masters

RS-485

network

S S S

M M M

Modbus / TCP Masters (up to 16 masters)

Modbus RTU / ASCIISlave Devices

M M

S S S

RS-485

network

M

Aport-212

Block Diagram

Module / TCP Masters toModbus RTU / ASCII Slaves

Aport-212

Modbus RTU / ASCII Masters toModule / TCP Slaves


www.artila.com42

Optional Accessories

91-R45F9-150Serial Cable (RJ45 to DB9 Female, 150cm)

Model No.:• Matrix-500,Matrix-504,Matrix-505,

Matrix-518, Matrix-604, Matrix-605• PAC-4000,PAC-4010,PAC-4070

91-0P9M9-001Console Cable (10Pin Header to DB9 Male, 20cm)


Matrix-618, Matrix-522• M-5360AStarterKit• PAC-5010,PAC-5070• RIO-2010,RIO-2010PG

91-PHDF9-050Console Cable (Wafer Box to DB9 Female, 50cm)

Model No.: • Matrix-505,Matrix-605• M-502,M-503,M-9G45A• PAC-4000,PAC-4010,PAC-4070

Pigtail-WiFi-1001-20IPEX to RP-SMA Female Coaxial Cable, 20cm

Model No.:• Matrix-513

Ant-WiFi-10015dBi External WiFi Antenna

Model No.: • Matrix-513

M-9001 (EWM-W150H)�802.11 b/g/n Half-size miniPCIe WiFi Card


PWR-12V-1A110~240VAC to 12VDC 1A Power Adapter


Matrix-513, Matrix-604, Matrix-605• Aport-211S,Aport-212,Aport-212PG• PAC-4000,PAC-4010,PAC-4070• RIO-2010,RIO-2010PG,RIO-2017,

RIO-2018

91-RJCON-100Console Cable (RJ45 to DB9 Female, 100cm)

Model No.:• Matrix-500,Matrix-504,Matrix-604• Aport-212,Aport-212PG

91-DBCON-100Console Cable (DB9 Female to DB9 Female, 100cm)


DK-35ADIN RAIL Mounting Kit


Matrix-512, Matrix-513, Matrix-516, Martix-518, Matrix-522, Matrix-604, Matrix-605

• Aport-211S,Aport-212,Aport-212PG• RIO-2017,RIO-2018

Pigtail-3G-1001-20IPEX to SMA Female Coaxial Cable, 20cm


Ant-3G-10015dBi External 2G / 3G Antenna


M-9011 (CM5000)�Full-size miniPCIe 2G / 3G Card, with SIM Socket


Your Trusted Partner for Device Networking & Computing

Intelligent IoT GatewayIoT Device PlatformProgrammable Automation ControllerWeb-based Remote I/O

www.artila.com

Artila Electronics Co., Ltd.

www.artila.com

4F., No. 6, Lane 130, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)Tel: +886-2-8667-2340Fax: +886-2-8667-3240Email: [email protected]

All specifications are subject to change without further notice.

All products and company names listed are trademarks or trade names of their respective companies.

50-401502

your trusted partner for device networking & computing · • 4 x 921.6kbps high speed tty...

Documents