your new adiod service - at&t€¦ · at&t dedicated internet on demand (adiod) uses a...
TRANSCRIPT
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 1
AT&T Network on Demand: Connecting to ADIoD - The Basics
Your new ADIoD Service
AT&T Dedicated Internet on Demand (ADIoD) uses a virtual AT&T Managed router and firewall. The
router/firewall is located in the AT&T Integrated Cloud, instead of at customer’s site. Customers access
router and firewall services via the ADI Business Center portal.
Depending on your site arrangement, you may need to configure your equipment for it to work with
ADIoD.
Before You Begin
Before you can configure your network or turn up your service you need:
Your equipment connected to the AT&T demarc/patch panel/NTE
Inside wire completed
Your equipment manufacturer’s configuration guide
Access to your Business Center portal
Locate Site Inventory in your Business Center Portal:
Configuring your equipment requires you to obtain IP Addresses from the Business center portal. To do so,
you must enter the portal and navigate to the site you are intending to configure.
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 2
AT&T Network on Demand: Connecting to ADIoD - The Basics
1. Access your Business Portal
2. In the NoD Inventory widget click the Manage button to launch a list of your sites
3. Find your desired site in the inventory list, then click (+) to view the Internet circuit(s) for that site.
Connecting to a Router, VPN Device, or Firewall:
To connect to a router, VPN device, or firewall, you must configure your equipment to work with the ADIoD
service using a Static Route with AT&T-assigned IP Addresses. To do this, you will need to find your
assigned IP Addresses for your site as follows:
1. Access your Business Portal
2. Navigate to the site you wish to configure and use the Manage dropdown to select Edit L3
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 3
AT&T Network on Demand: Connecting to ADIoD - The Basics
3. This will bring you to the Router LAN Settings Page. Using this as an example, configure your
equipment with the following:
Connecting a Device that Requires Access from Internet
If your device requires outside access (an email server or VPN for instance), you must enable 1-to-1 Network
Address Translation (NAT) on the AT&T virtual router, and then add your device to our built-in firewall.
1. Access your Business Portal
2. Navigate to the site you wish to configure and use the Manage dropdown to select Edit L3
3. Write down the values shown under IPv4 Public LAN Block (outlined in blue in this example below).
You will need to capture this information for entry on next screens.
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 4
AT&T Network on Demand: Connecting to ADIoD - The Basics
4. Once you have noted these values, scroll to the bottom of the page and click continue. You will now
be on page 2 - Virtual Router Optional Features
5. If Network Address Translation for IPv4 is not enabled, select edit
6. Select the Yes radial button to enable NAT. This will open a new section for Network Address
Translation Mapping
7. Using this example for reference, configure your device as follows:
NOTE: If you receive an error on Next-Hop after clicking continue, go back and edit to delete the
value and proceed without it. Error example:
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 5
AT&T Network on Demand: Connecting to ADIoD - The Basics
8. Next, you must add your device to the built in Firewall. To do this, navigate back to your Inventory
page to locate the site and internet that you are configuring.
9. Use the Manage dropdown to select Configure Firewall.
10. The Firewall Management environment opens in a new browser window.
11. In the IPv4 Filters tab, in the WAN Rules section, select Add Rule and configure as follows:
February 1, 2017 © 2017 AT&T Intellectual Property. All rights reserved. AT&T and the Globe logo are registered trademarks of AT&T Intellectual Property 6
AT&T Network on Demand: Connecting to ADIoD - The Basics
Refer to the Firewall Guide for additional information about using the firewall.
This concludes steps for setup with AT&T’s virtual router and firewall in the cloud. If you are setting up a
VPN from your own firewall, you may take additional steps to:
Enable NAT-Transversal (NAT-T) on your firewall
Enter in the public NAT IP for your tunnel source on your firewall
Need Assistance?
For assistance with setting up more complex configurations, refer to the Getting Started Guide, or call our
AT&T Network on Demand Toll Free Number 844-ATT-NOD3.