xs5104 ghcema bcd cat
TRANSCRIPT
Goodman-Hewitt Products
CEMA B,C &D Ball Bearing SeriesCEMA C & D Roller Bearing Series
CEMA B, C & D Ball Bearing SeriesCEMA C & D Roller Bearing Series
Goodman-Hewitt Products
22
Idler Identification Guide
CEMA Series & Roll Dia. B - 4" & 5" C- 4", 5", & 6" D - 5" & 6" E - 6" & 7"
Angle10° - V-RETURN20°35°45°
Belt WidthB = 18" - 48"C = 18" - 60"D = 24" - 72"E = 36" - 96"
Idler TypeT = Troughing IdlerTP = Troughing Idler Picking/FeederTO = Troughing Idler Offset TPO = Troughing Idler Picking Feeder OffsetTI = Troughing Idler ImpactTPI = Troughing Idler Picking/Feeder ImpactTOI = Troughing Idler Offset ImpactTA = Troughing Self-AligningTAB = Troughing Self-Aligning Bidirectional ReversingTSS = Troughing Scale Service TSQ = Troughing Scale QualityTCM = Troughing Inside Channel MountTCMI = Troughing Inside Channel Mount ImpactTSM = Troughing Low Profile Standard MountTV = Troughing Idler Variable Trough AngleTW = Troughing Wire Rope or Rigid Rail RF = Return/Flat Roll (hangers or stands separate)RFD = Return/Flat Disc (hangers or stands separate)RFI = Return/Flat Impact (hangers or stands separate)RA = Return Self-AligningRAD = Return Self-Aligning DiscRAB = Return Self-Aligning Bidirectional ReversingRAW = Return Self-Aligning WobblerRV = Return VFV = Inverted V FA = Flat Carrying Self-AligningL = Live Shaft (Pillow block bearings separate)LI = Live Shaft Impact (Pillow block bearings separate)
Retrofit RollsCSL = return roll only GCC CSL SeriesDBT = roll only BucyrusFMC = roll only FMC PPI = roll only Precision REX = roll only REX SA = roll only Stephens AdamsonSUP = roll only Superior SUPN = old Superior roll with nut2000S = return roll HR 2000 S SeriesOthers = consult factory
BearingB = Ball Bearing SealedR = Tapered Roller Bearing (Sealed Roll)
Roll Examples: Troughing replacement roll C5-T-36BImpact troughing replacement roll C5-TI-36B
C5 3635 B UT- -
Suffix U = PolyurethaneE = PolyethyleneG = Grain Troughing IdlerC = Catenary/Garland IdlerW = Wide base, BW+15”7 = 7 gauge shell thickness4 = 1/4” shell thicknessX = SpecialXP = Special Project
33
20MM SOLID SHAFT
�
1" SOLID SHAFT REDUCEDTO 25 MM AT BEARING
1-1/4" SHAFT REDUCEDTO 3/4" AT BEARING
3/4" SOLID SHAFT
17 MM SOLID SHAFT
B Series Roll Design Features
Flinger
Exterior Shield
Grease Filled Multi-PathLabyrinth
Contact Seal
Back Seal
20 mm 6304Ball Bearing
3/4" TaperedRoller Bearing
Inner Shield
Grease FilledHorizontalLabyrinth
Exterior Outer Shield
17mm Ball Bearing
Interference Press Fit
Flinger
Exterior Shield
Grease Filled Multi-PathLabyrinth
Contact Seal
C Series Roll Design Features
CEMA D Roll Design Features
Flinger
ExteriorShield
Grease Filled Multi-Path Labyrinth
Contact Seal
Back Seal
Flinger
ExteriorShield
Grease Filled Multi-Path Labyrinth
Contact Seal
Special 25 mm6305 Ball Bearing
3/4" TaperedRoller Bearing
Roll Design Features
44
CEMA B Ball Bearing20 DEG TROUGHING IDLER B4-20T-(BW)B 4" DIAMETER ROLL
20 DEG TROUGHING IDLER B5-20T-(BW)B 5" DIAMETER ROLL
35 DEG TROUGHING IDLER B4-35T-(BW)B 4" DIAMETER ROLL
35 DEG TROUGHING IDLER B5-35T-(BW)B 5" DIAMETER ROLL
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 61/21/2 - Bolt
15" 2"
20°
A
B
CD
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 61/21/2 - Bolt
15" 2"
20°
A
B
CD
Roll dia.
A
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 61/21/2 - Bolt
15" 2"
35°
B
CD
Roll dia.
A
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 61/21/2 - Bolt
15" 2"
35°
B
CD
Roll dia.
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 24 28 215⁄8 615⁄16 71⁄8 95⁄8
24 29 32 279⁄16 9 71⁄8 103⁄8
30 33 37 331⁄2 111⁄16 71⁄8 111⁄16
36 40 44 397⁄16 131⁄8 71⁄8 113⁄4
42 44 53 453⁄16 151⁄8 71⁄8 127⁄16
48 50 57 51 171⁄8 71⁄8 131⁄8
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 25 29 197⁄16 615⁄16 71⁄8 111⁄4
24 30 33 247⁄8 9 71⁄8 121⁄2
30 34 38 305⁄16 111⁄16 71⁄8 135⁄8
36 41 45 353⁄4 131⁄8 71⁄8 1413⁄16
42 45 48 411⁄16 151⁄8 71⁄8 16
48 51 - 455⁄16 171⁄8 71⁄8 171⁄8
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 28 32 215⁄16 615⁄16 75⁄8 101⁄8
24 33 36 271⁄4 9 75⁄8 1013⁄16
30 38 42 333⁄16 111⁄16 75⁄8 119⁄16
36 46 49 391⁄8 131⁄8 75⁄8 121⁄4
42 51 54 447⁄8 151⁄8 75⁄8 1215⁄16
48 57 64 505⁄8 171⁄8 75⁄8 139⁄16
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 28 - 187⁄8 615⁄16 75⁄8 1111⁄16
24 34 37 241⁄4 9 75⁄8 127⁄8
30 39 43 293⁄4 111⁄16 75⁄8 141⁄16
36 47 50 353⁄16 131⁄8 75⁄8 151⁄4
42 52 55 407⁄16 151⁄8 75⁄8 163⁄8
48 58 - 453⁄4 171⁄8 75⁄8 171⁄2
55
Ball Bearing CEMA B
45 DEG TROUGHING IDLER B5-45T-(BW)B 5" DIAMETER ROLL
RETURN/FLAT CARRYING IDLER B4-RF-(BW)B 4" DIAMETER ROLL
RETURN/FLAT CARRYING IDLER B5-RF-(BW)B 5" DIAMETER ROLL
Belt width +15" for wide baseBelt width +9" for standard base
5/8" x 11/8" lg. slots - center slot also provided
33/4 23/4
1/2" - Bolts
4"
6"
4"
6"
11/2" Drop hanger no.: 376685031/2" Drop hanger no.: 376773341/2" Drop hanger no.: 779931
11/2" Rise bracket no.: 71H600131/2" Rise bracket no.: 332211541/2" Rise bracket no.: 779930
Belt width +15" for wide baseBelt width +9" for standard base
5/8" x 11/8" lg. slots - center slot also provided
33/4 23/4
1/2" - Bolts
4"
6"
4"
6"
11/2" Drop hanger no.: 376685031/2" Drop hanger no.: 376773341/2" Drop hanger no.: 779931
11/2" Rise bracket no.: 71H600131/2" Rise bracket no.: 332211541/2" Rise bracket no.: 779930
Belt width +9" for standard baseBelt width +15" for wide base
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 71/2
D
Roll dia.
1/2 - Bolt2"
45°
A
B
C
1
45 DEG TROUGHING IDLER B4-45T-(BW)B 4" DIAMETER ROLL
Belt width +9" for standard baseBelt width +15" for wide base
9/16 x 11/2 lg.Center slot foroptional one bolt mounting
81/2
1/4
53/4 - 71/2
D
Roll dia.
1/2 - Bolt2"
45°
A
B
C
1
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 27 31 181⁄2 615⁄16 71⁄8 123⁄8
24 32 35 231⁄2 9 71⁄8 1313⁄16
30 36 40 281⁄2 111⁄16 71⁄8 155⁄16
36 42 47 337⁄16 131⁄8 71⁄8 163⁄4
42 47 50 381⁄4 151⁄8 71⁄8 183⁄16
48 53 – 431⁄8 171⁄8 71⁄8 195⁄8
Belt Width
Std.Base
Wide Base A B C D
Wt. Wt.18 29 – 1713⁄16 615⁄16 75⁄8 123⁄4
24 36 39 223⁄4 9 75⁄8 1413⁄16
30 41 45 273⁄4 111⁄16 75⁄8 1511⁄16
36 49 52 323⁄4 131⁄8 75⁄8 171⁄8
42 54 57 379⁄16 151⁄8 75⁄8 189⁄16
48 60 – 423⁄8 171⁄8 75⁄8 1915⁄16
Belt Width
4"Std.Wt.
A
18 15 211⁄8
24 18 271⁄8
30 21 331⁄8
36 24 391⁄8
42 27 451⁄8
48 31 511⁄8
Belt Width
5"Std.Wt.
A
18 17 211⁄8
24 21 271⁄8
30 25 331⁄8
36 28 391⁄8
42 32 451⁄8
48 35 511⁄8
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
66
20 DEG. TROUGHING IDLER C6-20T-(BW)B OR C6-20T-(BW)R 6" DIA ROLL
35 DEG. TROUGHING IDLER C5-35T-(BW)B OR C5-35T-(BW)R 5" DIA ROLL
35 DEG. TROUGHING IDLER C6-35T-(BW)B OR C6-35T-(BW)R 6" DIA ROLL
CEMA C Ball Or Tapered Roller Bearing20 DEG. TROUGHING IDLER C5-20T-(BW)B OR C5-20T-(BW)R 5" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"1"1"
B
D
Roll dia.
20°
A
C
E
Wide Base Shown Standard Base Shown
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
20°
A
B
CD
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
35°
A
B
C
D
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
35°
A
B
C
D
Roll dia.
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 45 50 1913⁄16 71⁄8 89⁄16 1213⁄16 61⁄4 - 9
24 51 57 243⁄4 9 89⁄16 137⁄8 61⁄4 - 9
30 60 62 30 11 89⁄16 15 61⁄4 - 9
36 68 70 355⁄16 13 89⁄16 163⁄16 61⁄4 - 9
42 81 83 409⁄16 15 87⁄8 175⁄8 61⁄4 - 9
48 93 95 457⁄8 17 87⁄8 1813⁄16 7 - 9
54 106 108 511⁄8 19 91⁄4 205⁄16 7 - 9
60 115 118 563⁄8 21 91⁄4 217⁄16 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 52 57 191⁄4 71⁄8 91⁄16 133⁄16 61⁄4 - 9
24 59 65 243⁄16 9 91⁄16 145⁄16 61⁄4 - 9
30 71 73 297⁄16 11 91⁄16 157⁄16 61⁄4 - 9
36 79 81 343⁄4 13 91⁄16 169⁄16 61⁄4 - 9
42 93 95 40 15 93⁄8 181⁄16 61⁄4 - 9
48 107 109 451⁄4 17 93⁄8 193⁄16 7 - 9
54 121 124 509⁄16 19 93⁄4 2011⁄16 7 - 9
60 132 134 5513⁄16 21 93⁄4 217⁄8 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 51 – 215⁄8 71⁄8 91⁄16 115⁄8 61⁄4 - 9
24 59 63 27 9 91⁄16 121⁄4 61⁄4 - 9
30 69 70 323⁄4 11 91⁄16 131⁄4 61⁄4 - 9
36 77 78 381⁄2 13 91⁄16 135⁄8 61⁄4 - 9
42 90 93 445⁄16 15 93⁄8 145⁄8 61⁄4 - 9
48 104 106 501⁄16 17 93⁄8 155⁄16 7 - 9
54 116 118 5513⁄16 19 93⁄4 163⁄8 7 - 9
60 125 128 619⁄16 21 93⁄4 17 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 44 48 2115⁄16 71⁄8 89⁄16 111⁄8 61⁄4 - 9
24 50 55 273⁄8 9 89⁄16 113⁄4 61⁄4 - 9
30 58 60 331⁄8 11 89⁄16 127⁄16 61⁄4 - 9
36 66 67 387⁄8 13 89⁄16 131⁄8 61⁄4 - 9
42 78 80 445⁄8 15 87⁄8 141⁄8 61⁄4 - 9
48 90 92 503⁄8 17 87⁄8 1413⁄16 7 - 9
54 100 103 561⁄8 19 91⁄4 157⁄8 7 - 9
60 109 111 6115⁄16 21 91⁄4 169⁄16 7 - 9
77
45 DEG. TROUGHING IDLER C5-45T-(BW)B OR C5-45T-(BW)R 5" DIA ROLL
Ball Or Tapered Roller Bearing CEMA C
RETURN/FLAT CARRYING IDLER C5-RF-(BW)B OR C5-RF-(BW)R 5" DIA ROLL
45 DEG. TROUGHING IDLER C6-45T-(BW)B OR C6-45T-(BW)R 6" DIA ROLL
RETURN/FLAT CARRYING IDLER C6-RF-(BW)B OR C6-RF-(BW)R 6" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
45°
A
B
C
D
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
41/2" Drop hangerPart no.: 69H5834
41/2" Rise standPart no.: 779932
3/16"
3/16"
33/4"23/4" 23/4"33/4"
4"
6"
4"
6"A
Center slot provided risebracket - only
1/2" Bolts
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
45°
A
B
C
D
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
41/2" Drop hangerPart no.: 69H5834
41/2" Rise standPart no.: 779932
3/16"
3/16"
33/4"23/4" 23/4"33/4"
4"
6"
4"
6"A
Center slot provided risebracket - only
1/2" Bolts
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 49 54 19 71⁄8 89⁄16 14 61⁄4 - 9
24 56 61 231⁄2 9 89⁄16 155⁄16 61⁄4 - 9
30 67 68 285⁄16 11 89⁄16 163⁄4 61⁄4 - 9
36 75 76 331⁄8 13 89⁄16 181⁄8 61⁄4 - 9
42 88 90 38 15 87⁄8 197⁄8 61⁄4 - 9
48 101 104 4213⁄16 17 87⁄8 215⁄16 7 - 9
54 110 113 445⁄8 19 91⁄4 231⁄16 7 - 9
60 120 123 521⁄2 21 91⁄4 241⁄2 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 56 61 181⁄4 71⁄8 91⁄16 143⁄8 61⁄4 - 9
24 64 69 2213⁄16 9 91⁄16 1511⁄16 61⁄4 - 9
30 78 79 275⁄8 11 91⁄16 171⁄16 61⁄4 - 9
36 86 87 327⁄16 13 91⁄16 181⁄2 61⁄4 - 9
42 100 102 375⁄16 15 93⁄8 201⁄4 61⁄4 - 9
48 115 118 421⁄8 17 93⁄8 2111⁄16 7 - 9
54 125 129 4615⁄16 19 93⁄4 237⁄16 7 - 9
60 137 139 513⁄4 21 93⁄4 247⁄8 7 - 9
Return/Flat Carrying
Belt Width
5" Std.Wt.
A
18 23 21
24 28 27
30 32 33
36 36 39
42 40 45
48 45 51
Return/Flat Carrying
Belt Width
6" Std.Wt.
A
18 29 21
24 34 27
30 40 33
36 45 39
42 51 45
48 57 51
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
88
10 DEG. V RETURN IDLER C5-10RV-(BW)B OR C5-10RV-(BW)R 5" DIA ROLL
DISC RETURN C5-RFD-(BW)B 5" DIA ROLL
CEMA C Ball And Tapered Roller Bearing
DISC RETURN C6-RFD-(BW)B 6" DIA ROLL
10 DEG. V RETURN IDLER C6-10RV-(BW)B OR C6-10RV-(BW)R 6" DIA ROLL
Belt width +9" for standard base
For wide base use next larger belt width
5/8" Bolt
11/2"
41/4"
101/2"
4" - 81/2"11/2"
B10°
A
A4"
6"
1/2" Bolts
41/2"
Drop hanger pn: 69H5834
41 / 2"
Belt width +9" for standard baseBelt width +15" for wide base
A4"
6"
1/2" Bolts
Drop hanger pn: 69H5834
41 / 2"
41/2"
Belt width +9" for standard baseBelt width +15" for wide base
Belt width +9" for standard base
For wide base use next larger belt width
5/8" Bolt
11/2"
41/4"
101/2"
4" - 81/2"11/2"
B10°
A
5 Inch ReturnRubber Disc
Belt Width
Std.Wt.
A
18 24 211⁄8
24 29 271⁄8
30 34 331⁄8
36 39 391⁄8
42 44 451⁄8
48 49 511⁄8
6 Inch ReturnRubber Disc
Belt Width
Std.Wt.
A
18 30 211⁄8
24 35 271⁄8
30 42 331⁄8
36 48 391⁄8
42 54 451⁄8
48 61 511⁄8
Belt Width
5"Std.Wt.
A B
24 63 13 101⁄4
30 71 17 103⁄4
36 76 19 115⁄16
42 83 23 1113⁄16
48 87 27 125⁄16
54 101 29 127⁄8
60 107 33 133⁄8
Belt Width
6"Std.Wt.
A B
24 69 13 101⁄4
30 79 17 103⁄4
36 84 19 115⁄16
42 93 23 1113⁄16
48 100 27 125⁄16
54 115 29 127⁄8
60 123 33 133⁄8
99
Ball Bearing CEMA C
35 DEG. IMPACT TROUGHING IDLER C6-35TI-(BW)B 6" DIA ROLL
35 DEG. IMPACT TROUGHING IDLER C5-35TI-(BW)B 5" DIA ROLL
20 DEG. IMPACT TROUGHING IDLER C6-20TI-(BW)B 6" DIA ROLL
20 DEG. IMPACT TROUGHING IDLER C5-20TI-(BW)B 5" DIA ROLL
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
35°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
35°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"1"1"
B
D
Roll dia.
20°
A
C
E
42" Belt and above have reinforced frame and center stand
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"1"1"
B
D
Roll dia.
20°
A
C
E
42" Belt and above have reinforced frame and center stand Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 43 48 215⁄16 71⁄16 89⁄16 11 61⁄4 - 9
24 52 57 2611⁄16 815⁄16 89⁄16 115⁄8 61⁄4 - 9
30 61 63 327⁄16 1015⁄16 89⁄16 125⁄16 61⁄4 - 9
36 70 72 383⁄16 1215⁄16 89⁄16 13 61⁄4 - 9
42 91 95 44 1415⁄16 87⁄8 14 61⁄4 - 9
48 112 114 493⁄4 1615⁄16 87⁄8 1411⁄16 7 - 9
54 123 126 551⁄2 1815⁄16 91⁄4 153⁄4 7 - 9
60 135 138 611⁄4 2015⁄16 91⁄4 167⁄16 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 47 52 2015⁄16 71⁄16 91⁄16 111⁄2 61⁄4 - 9
24 58 63 265⁄16 815⁄16 91⁄16 121⁄8 61⁄4 - 9
30 68 70 321⁄8 1015⁄16 91⁄16 1213⁄16 61⁄4 - 9
36 79 81 377⁄8 1215⁄16 91⁄16 131⁄2 61⁄4 - 9
42 102 106 435⁄8 1415⁄16 93⁄8 141⁄2 61⁄4 - 9
48 124 126 493⁄8 1615⁄16 93⁄8 153⁄16 7 - 9
54 136 139 551⁄8 1815⁄16 93⁄4 161⁄4 7 - 9
60 150 153 6015⁄16 2015⁄16 93⁄4 1615⁄16 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 45 50 191⁄4 71⁄16 89⁄16 125⁄8 61⁄4 - 9
24 54 59 243⁄16 815⁄16 89⁄16 1311⁄16 61⁄4 - 9
30 63 65 297⁄16 1015⁄16 89⁄16 1413⁄16 61⁄4 - 9
36 72 74 343⁄4 1215⁄16 89⁄16 16 61⁄4 - 9
42 90 93 40 1415⁄16 87⁄8 177⁄16 61⁄4 - 9
48 113 116 451⁄4 1615⁄16 87⁄8 189⁄16 7 - 9
54 122 126 509⁄16 1815⁄16 91⁄4 201⁄8 7 - 9
60 135 138 5513⁄16 2015⁄16 91⁄4 211⁄4 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 49 50 185⁄8 71⁄16 91⁄16 13 61⁄4 - 9
24 59 65 239⁄16 815⁄16 91⁄16 141⁄16 61⁄4 - 9
30 70 72 287⁄8 1015⁄16 91⁄16 151⁄4 61⁄4 - 9
36 81 83 341⁄8 1215⁄16 91⁄16 163⁄8 61⁄4 - 9
42 112 120 397⁄16 1415⁄16 93⁄8 1713⁄16 61⁄4 - 9
48 136 140 4411⁄16 1615⁄16 93⁄8 19 7 - 9
54 148 151 50 1815⁄16 93⁄4 201⁄2 7 - 9
60 164 166 551⁄4 2015⁄16 93⁄4 2111⁄16 7 - 9
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
1010
CEMA C Ball Bearing
20 DEG. IMPACT CHANNEL MOUNT IDLER C5-20TCMI-(BW)B 5" DIA ROLL
35 DEG. IMPACT CHANNEL MOUNT IDLER C5-35TCMI-(BW)B 5" DIA ROLL
45 DEG. IMPACT TROUGHING IDLER C6-45TI-(BW)B 6" DIA ROLL
45 DEG. IMPACT TROUGHING IDLER C5-45TI-(BW)B 5" DIA ROLL
5" dia.Top ofcenter roll
4" 3"
1"
4"
A
B
C
D20°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
5" dia.Top ofcenter roll
4" 3"
1"
4"
A
B
C
D
35°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
45°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
45°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 43 46 1711⁄16 71⁄16 89⁄16 139⁄16 61⁄4 - 9
24 52 57 223⁄16 815⁄16 89⁄16 147⁄8 61⁄4 - 9
30 61 63 27 1015⁄16 89⁄16 161⁄4 61⁄4 - 9
36 70 72 3113⁄16 1215⁄16 89⁄16 1711⁄16 61⁄4 - 9
42 91 95 3611⁄16 1415⁄16 87⁄8 197⁄16 61⁄4 - 9
48 112 114 411⁄2 1615⁄16 87⁄8 2013⁄16 7 - 9
54 123 126 465⁄16 1815⁄16 91⁄4 225⁄8 7 - 9
60 135 138 511⁄8 2015⁄16 91⁄4 241⁄16 7 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
18 49 55 1615⁄16 71⁄16 91⁄16 1315⁄16 61⁄4 - 9
24 58 63 211⁄2 815⁄16 91⁄16 151⁄4 61⁄4 - 9
30 70 71 265⁄16 1015⁄16 91⁄16 165⁄8 61⁄4 - 9
36 79 81 311⁄8 1215⁄16 91⁄16 181⁄16 61⁄4 - 9
42 112 120 3515⁄16 1415⁄16 93⁄8 193⁄4 61⁄4 - 9
48 136 140 403⁄4 1615⁄16 93⁄8 213⁄16 7 - 9
54 148 151 455⁄8 1815⁄16 93⁄4 23 7 - 9
60 164 166 507⁄16 2015⁄16 93⁄4 247⁄16 7 - 9
Belt Width
Std.Wt.
A B C D
24 44 251⁄4 11 63⁄4 815⁄16
30 49 311⁄2 13 9 911⁄16
36 57 371⁄4 15 11 103⁄8
42 65 43 17 13 111⁄16
48 73 483⁄4 19 15 113⁄4
54 80 541⁄2 21 17 127⁄16
60 87 601⁄2 23 19 131⁄8
Belt Width
Std.Wt.
A B C D
24 45 233⁄16 11 63⁄4 101⁄2
30 50 287⁄8 13 9 1113⁄16
36 59 341⁄8 15 11 13
42 66 397⁄16 17 13 141⁄8
48 75 4411⁄16 19 15 151⁄4
54 82 50 21 17 167⁄16
60 89 551⁄4 23 19 179⁄16
1111
20 DEG. CHANNEL MOUNT IDLER C4-20TCM-(BW)B 4" DIA ROLL
35 DEG. CHANNEL MOUNT IDLER C4-35TCM-(BW)B 4" DIA ROLL
20 DEG. CHANNEL MOUNT IDLER C5-20TCM-(BW)B 5" DIA ROLL
35 DEG. CHANNEL MOUNT IDLER C5-35TCM-(BW)B 5" DIA ROLL
Ball Bearing CEMA C
21/2" for 4" rollsTop ofcenter roll
4"
1"
4"
A
B
C
D20°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
21/2" for 4" rollsTop ofcenter roll
4"
1"
4"
A
B
C
D
35°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
3" for 5" rollsTop ofcenter roll
4"
1"
4"
A
B
C
D20°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
3" for 5" rollsTop ofcenter roll
4"
1"
4"
A
B
C
D
35°
Belt width + 55/8"
9/16" x 1" slot - typ.21/4"
Belt Width
Std.Wt.
A B C D
24 33 255⁄8 11 67⁄8 81⁄2
30 37 3113⁄16 13 9 91⁄4
36 45 379⁄16 15 11 915⁄16
42 51 435⁄16 17 13 105⁄8
48 57 491⁄8 19 15 111⁄4
54 64 5413⁄16 21 17 12
60 71 605⁄8 23 19 1211⁄16
Belt Width
Std.Wt.
A B C D
24 36 251⁄4 11 67⁄8 815⁄16
30 43 311⁄2 13 9 911⁄16
36 50 371⁄4 15 11 103⁄8
42 56 43 17 13 111⁄16
48 63 483⁄4 19 15 113⁄4
54 70 541⁄2 21 17 127⁄16
60 77 601⁄4 23 19 131⁄8
Belt Width
Std.Wt.
A B C D
24 34 233⁄4 11 67⁄8 101⁄8
30 38 297⁄16 13 9 117⁄16
36 46 343⁄4 15 11 129⁄16
42 52 40 17 13 1311⁄16
48 59 451⁄4 19 15 147⁄8
54 65 509⁄16 21 17 16
60 72 5513⁄16 23 19 171⁄8
Belt Width
Std.Wt.
A B C D
24 37 233⁄16 11 67⁄8 101⁄2
30 44 287⁄8 13 9 1113⁄16
36 51 341⁄8 15 11 13
42 58 397⁄16 17 13 141⁄8
48 64 4411⁄16 19 15 151⁄4
54 70 50 21 17 167⁄16
60 77 551⁄4 23 19 179⁄16
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
1212
20 DEG. TROUGHING IDLER D5-20T-(BW)B OR D5-20T-(BW)R 5" DIA ROLL
20 DEG. TROUGHING IDLER D6-20T-(BW)B OR D6-20T-(BW)R 6" DIA ROLL
35 DEG. TROUGHING IDLER D5-35T-(BW)B OR D5-35T-(BW)R 5" DIA ROLL
35 DEG. TROUGHING IDLER D6-35T-(BW)B OR D6-35T-(BW)R 6" DIA ROLL
CEMA D Ball Or Tapered Roller Bearing
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
20°
A
B
CD
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
20°
A
B
CD
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
35°
A
B
C
D
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
35°
A
B
C
D
Roll dia.
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 53 59 273⁄8 9 89⁄16 113⁄4 61⁄4 - 930 60 67 331⁄8 11 87⁄8 123⁄4 61⁄4 - 936 72 80 387⁄8 13 87⁄8 137⁄16 61⁄4 - 942 85 87 445⁄8 15 87⁄8 141⁄8 61⁄4 - 948 93 96 503⁄8 17 91⁄4 153⁄16 7 - 954 109 112 561⁄8 19 91⁄4 157⁄8 7 - 960 118 121 6115⁄16 21 91⁄4 169⁄16 7 - 966 127 130 681⁄8 23 95⁄8 175⁄8 71⁄2 - 972 136 139 737⁄8 25 95⁄8 185⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 61 66 27 9 91⁄16 121⁄4 61⁄4 - 930 70 76 323⁄4 11 93⁄8 131⁄4 61⁄4 - 936 83 90 389⁄16 13 93⁄8 1315⁄16 61⁄4 - 942 97 100 445⁄16 15 93⁄8 145⁄8 61⁄4 - 948 107 110 501⁄16 17 93⁄4 1511⁄16 7 - 954 124 127 5513⁄16 19 93⁄4 163⁄8 7 - 960 135 138 619⁄16 21 93⁄4 17 7 - 966 145 148 675⁄16 23 101⁄8 181⁄16 71⁄2 - 972 155 158 731⁄16 25 101⁄8 183⁄4 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 54 60 243⁄4 9 89⁄16 137⁄8 61⁄4 - 930 62 69 30 11 87⁄8 155⁄16 61⁄4 - 936 75 82 355⁄16 13 87⁄8 161⁄2 61⁄4 - 942 87 90 409⁄16 15 87⁄8 175⁄8 61⁄4 - 948 96 99 457⁄8 17 91⁄4 193⁄16 7 - 954 114 117 511⁄8 19 91⁄4 205⁄16 7 - 960 124 127 563⁄8 21 91⁄4 217⁄16 7 - 966 134 137 6111⁄16 23 95⁄8 23 71⁄2 - 972 144 158 6615⁄16 25 95⁄8 241⁄8 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 62 68 243⁄16 9 91⁄16 145⁄16 61⁄4 - 930 72 78 297⁄16 11 93⁄8 1513⁄16 61⁄4 - 936 85 93 343⁄4 13 93⁄8 167⁄8 61⁄4 - 942 100 102 40 15 93⁄8 181⁄16 61⁄4 - 948 110 112 451⁄4 17 93⁄4 199⁄16 7 - 954 129 133 509⁄16 19 93⁄4 2011⁄16 7 - 960 141 144 5513⁄16 21 93⁄4 217⁄8 7 - 966 152 155 611⁄8 23 101⁄8 233⁄8 71⁄2 - 972 163 166 663⁄8 25 101⁄8 249⁄16 71⁄2 - 9
1313
45 DEG. TROUGHING IDLER D5-45T-(BW)B OR D5-45T-(BW)R 5" DIA ROLL
Ball Or Tapered Roller Bearing CEMA D
RETURN/FLAT CARRYING IDLER D5-RF-(BW)B OR D5-RF-(BW)R 5" DIA ROLL
45 DEG. TROUGHING IDLER D6-45T-(BW)B OR D6-45T-(BW)R 6" DIA ROLL
RETURN/FLAT CARRYING IDLER D6-RF-(BW)B OR D6-RF-(BW)R 6" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
45°
A
B
C
D
Roll dia.
Belt width +9" for standard baseBelt width +15" for wide base
Wide Base Shown Standard Base Shown
101/2
5/16"
E5/8" - Bolt
1" 1"
45°
A
B
C
D
Roll dia.
Belt width +15" for wide baseBelt width +9" for standard base
5/8" x 11/8" lg. slots - center slot also provided
33/4 23/4
1/2" - Bolts
4"
6"
4"
6"A
41/2" Drop hanger no.: 69H5834 41/2" Rise bracket no.: 779932
Belt width +15" for wide baseBelt width +9" for standard base
5/8" x 11/8" lg. slots - center slot also provided
33/4 23/4
1/2" - Bolts
4"
6"
4"
6"A
41/2" Drop hanger no.: 69H5834 41/2" Rise bracket no.: 779932
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 59 65 231⁄2 9 89⁄16 155⁄16 61⁄4 - 930 68 74 285⁄16 11 87⁄8 171⁄16 61⁄4 - 936 81 89 331⁄8 13 87⁄8 187⁄16 61⁄4 - 942 95 97 38 15 87⁄8 197⁄8 61⁄4 - 948 105 107 4213⁄16 17 91⁄4 2111⁄16 7 - 954 119 122 445⁄8 19 91⁄4 231⁄16 7 - 960 130 133 521⁄2 21 91⁄4 241⁄2 7 - 966 140 144 575⁄16 23 95⁄8 265⁄16 71⁄2 - 972 151 155 621⁄8 25 95⁄8 2711⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 59 65 2213⁄16 9 91⁄16 1511⁄16 61⁄4 - 930 68 74 275⁄8 11 93⁄8 173⁄8 61⁄4 - 936 81 89 327⁄16 13 93⁄8 1813⁄16 61⁄4 - 942 95 97 375⁄16 15 93⁄8 201⁄4 61⁄4 - 948 105 107 421⁄8 17 93⁄4 221⁄16 7 - 954 119 122 4615⁄16 19 93⁄4 237⁄16 7 - 960 130 133 513⁄4 21 93⁄4 247⁄8 7 - 966 140 144 569⁄16 23 101⁄8 265⁄8 71⁄2 - 972 151 155 617⁄16 25 101⁄8 281⁄16 71⁄2 - 9
5 Inch Return/Flat Carrying
Belt Width
Std.Wt. A
24 30 2730 34 3336 39 3942 44 4548 49 5154 54 5760 59 6366 63 6972 68 75
6 Inch Return/Flat Carrying
Belt Width
Std.Wt. A
24 36 2730 43 3336 49 3942 55 4548 61 5154 67 5760 73 6366 79 6972 85 75
Contact factory for other drop and rise heights.Drop/Stand weight included (4lbs/pr).
Contact factory for other drop and rise heights.Drop/Stand weight included (4lbs/pr).
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
1414
CEMA D Ball And Tapered Roller Bearing
10 DEG. V RETURN IDLER D5-10RV-(BW)B OR D5-10RV-(BW)R 5" DIA ROLL
10 DEG. V RETURN IDLER D6-10RV-(BW)B OR D6-10RV-(BW)R 6" DIA ROLL
DISC RETURN D5-RFD-(BW)B 5" DIA ROLL
DISC RETURN D6-RFD-(BW)B 6" DIA ROLL
Belt width +9" for standard base
5/8" Bolt11/2"
11/2"
4" - 81/2"
101/2"
41/4"
10°
A
B
For wide base use next larger belt width
Belt width +9" for standard base
5/8" Bolt11/2"
11/2"
4" - 81/2"
101/2"
41/4"
10°
A
B
For wide base use next larger belt width
A4"
6"
1/2" Bolts
Drop hanger pn: 69H5834
41 / 2"
41/2"
Belt width +9" for standard baseBelt width +15" for wide base
A4"
6"
1/2" Bolts
41/2"
Drop hanger pn: 69H5834
41 / 2"
Belt width +9" for standard baseBelt width +15" for wide base
5 Inch Return RUBBER DISC
Belt Width
Std.Wt. A
24 29 271⁄830 34 331⁄836 39 391⁄842 44 451⁄848 49 511⁄854 58 571⁄860 63 631⁄872 73 751⁄8
6 Inch Return RUBBER DISC
Belt Width
Std.Wt. A
24 35 271⁄830 42 331⁄836 48 391⁄842 54 451⁄848 61 511⁄854 64 571⁄860 68 631⁄872 79 751⁄8
Belt Width
5"Std. Wt. A B
24 63 13 101⁄430 71 17 103⁄436 76 19 115⁄16
42 83 23 1113⁄16
48 87 27 125⁄16
54 101 29 127⁄860 107 33 133⁄866 126 35 1472 133 39 141⁄2
Belt Width
6"Std. Wt. A B
24 76 13 101⁄430 84 17 103⁄436 92 19 115⁄16
42 102 23 1113⁄16
48 109 27 125⁄16
54 125 29 127⁄860 134 33 133⁄866 143 35 1472 150 39 141⁄2
1515
Ball Bearing CEMA D
35 DEG. IMPACT TROUGHING IDLER D6-35TI-(BW)B 6" DIA ROLL
35 DEG. IMPACT TROUGHING IDLER D5-35TI-(BW)B 5" DIA ROLL
20 DEG. IMPACT TROUGHING IDLER D6-20TI-(BW)B 6" DIA ROLL
20 DEG. IMPACT TROUGHING IDLER D5-20TI-(BW)B 5" DIA ROLL
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
35°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
35°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"1"1"
B
D
Roll dia.
20°
A
C
E
42" Belt and above have reinforced frame and center stand
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"1"1"
B
D
Roll dia.
20°
A
C
E
42" Belt and above have reinforced frame and center stand Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 57 61 2611⁄16 815⁄16 89⁄16 115⁄8 61⁄4 - 930 64 67 327⁄16 1015⁄16 87⁄8 125⁄8 61⁄4 - 936 73 95 333⁄16 1215⁄16 87⁄8 135⁄16 61⁄4 - 942 102 105 44 1415⁄16 87⁄8 14 61⁄4 - 948 114 117 493⁄4 1615⁄16 91⁄4 151⁄16 7 - 954 123 126 551⁄2 1815⁄16 91⁄4 153⁄4 7 - 960 141 144 611⁄4 2015⁄16 91⁄4 167⁄16 7 - 966 148 150 67 2215⁄16 95⁄8 171⁄2 71⁄2 - 972 154 158 723⁄4 2415⁄16 95⁄8 183⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 58 62 243⁄16 815⁄16 89⁄16 1311⁄16 61⁄4 - 930 66 69 297⁄16 1015⁄16 87⁄8 151⁄8 61⁄4 - 936 75 97 343⁄4 1215⁄16 87⁄8 161⁄4 61⁄4 - 942 105 108 40 1415⁄16 87⁄8 177⁄16 61⁄4 - 948 117 120 451⁄4 1615⁄16 91⁄4 1815⁄16 7 - 954 129 132 509⁄16 1815⁄16 91⁄4 201⁄8 7 - 960 147 150 551⁄8 2015⁄16 91⁄4 211⁄4 7 - 966 155 157 611⁄8 2215⁄16 95⁄8 223⁄4 71⁄2 - 972 162 165 663⁄8 2415⁄16 95⁄8 2315⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 60 66 265⁄16 815⁄16 91⁄16 121⁄8 61⁄4 - 930 68 74 321⁄8 1015⁄16 93⁄8 131⁄8 61⁄4 - 936 84 91 377⁄8 1215⁄16 93⁄8 133⁄4 61⁄4 - 942 100 102 435⁄8 1415⁄16 93⁄8 141⁄2 61⁄4 - 948 112 114 493⁄8 1615⁄16 93⁄4 159⁄16 7 - 954 128 131 551⁄8 1815⁄16 93⁄4 161⁄4 7 - 960 141 144 6015⁄16 2015⁄16 93⁄4 1615⁄16 7 - 966 154 157 6611⁄16 2215⁄16 101⁄8 18 71⁄2 - 972 163 166 727⁄16 2415⁄16 101⁄8 1811⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 61 67 239⁄16 815⁄16 91⁄16 141⁄16 61⁄4 - 930 70 76 287⁄8 1015⁄16 93⁄8 159⁄16 61⁄4 - 936 86 94 341⁄8 1215⁄16 93⁄8 1611⁄16 61⁄4 - 942 102 105 397⁄16 1415⁄16 93⁄8 1713⁄16 61⁄4 - 948 115 117 4411⁄16 1615⁄16 93⁄4 193⁄8 7 - 954 133 137 50 1815⁄16 93⁄4 201⁄2 7 - 960 147 150 551⁄4 2015⁄16 93⁄4 2111⁄16 7 - 966 161 164 609⁄16 2215⁄16 101⁄8 233⁄16 71⁄2 - 972 171 174 6513⁄16 2415⁄16 101⁄8 245⁄16 71⁄2 - 9
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
1616
CEMA D Ball Bearing
45 DEG. IMPACT TROUGHING IDLER D6-45TI-(BW)B 6" DIA ROLL
Accessories Ball or Tapered Roller Bearing20 DEG. PICKING EXTENDED CENTER ROLL D5-20TP-(BW)B OR D5-20TP-(BW)R 5" DIA ROLL
20 DEG. PICKING EXTENDED CENTER ROLL D6-20TP-(BW)B OR D6-20TP-(BW)R 6" DIA ROLL
45 DEG. IMPACT TROUGHING IDLER D5-45TI-(BW)B 5" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"
63/4"
11/2"1"
B
D
Roll dia.
20°
A
C
E
Wide Base Shown Standard Base Shown
Belt width +9" for standard baseBelt width +15" for wide base
5/8" Bolt
5/16"
101/2"
63/4"
11/2"1"
B
D
Roll dia.
20°
A
C
E
Wide Base Shown Standard Base Shown
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
45°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
42" belt and above have reinforced frame and center stand
E
D
C
Roll dia.A
B
1"1"
45°
Belt width + 9" for standard baseBelt width + 15" for wide base
5/8" Bolt
5/16"
101/2"
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 59 63 223⁄16 815⁄16 89⁄16 147⁄8 61⁄4 - 930 68 71 27 1015⁄16 87⁄8 165⁄8 61⁄4 - 936 77 99 3113⁄16 1215⁄16 87⁄8 18 61⁄4 - 942 108 111 3611⁄16 1415⁄16 87⁄8 197⁄16 61⁄4 - 948 120 123 411⁄2 1615⁄16 91⁄4 211⁄4 7 - 954 135 138 465⁄16 1815⁄16 91⁄4 225⁄8 7 - 960 153 156 511⁄8 2015⁄16 91⁄4 241⁄16 7 - 966 162 164 56 2215⁄16 95⁄8 2513⁄16 71⁄2 - 972 170 172 6013⁄16 2415⁄16 95⁄8 271⁄4 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 52 61 291⁄8 15 89⁄16 11 61⁄4 - 930 63 70 351⁄8 21 87⁄8 115⁄16 61⁄4 - 936 74 76 411⁄8 27 87⁄8 115⁄16 61⁄4 - 942 82 83 471⁄8 33 87⁄8 115⁄16 61⁄4 - 948 93 94 531⁄8 39 91⁄4 1111⁄16 7 - 954 102 105 591⁄8 45 91⁄4 1111⁄16 7 - 960 110 113 651⁄8 51 91⁄4 1111⁄16 7 - 972 126 141 771⁄8 63 95⁄8 121⁄16 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 66 72 211⁄2 815⁄16 91⁄16 151⁄4 61⁄4 - 930 76 82 265⁄16 1015⁄16 93⁄8 1615⁄16 61⁄4 - 936 93 100 311⁄8 1215⁄16 93⁄8 183⁄8 61⁄4 - 942 110 112 3515⁄16 1415⁄16 93⁄8 193⁄4 61⁄4 - 948 123 126 403⁄4 1615⁄16 93⁄4 219⁄16 7 - 954 138 141 455⁄8 1815⁄16 93⁄4 23 7 - 960 153 156 507⁄16 2015⁄16 93⁄4 247⁄16 7 - 966 167 170 551⁄4 2215⁄16 101⁄8 263⁄16 71⁄2 - 972 178 181 60 2415⁄16 101⁄8 275⁄8 71⁄2 - 9
Belt Width
Std.Wt.
Wide Wt.
A B C D E
24 55 64 283⁄4 15 91⁄16 111⁄2 61⁄4 - 930 68 75 343⁄4 21 93⁄8 1113⁄16 61⁄4 - 936 80 82 403⁄4 27 93⁄8 1113⁄16 61⁄4 - 942 89 90 463⁄4 33 93⁄8 1113⁄16 61⁄4 - 948 101 102 523⁄4 39 93⁄4 123⁄16 7 - 954 112 115 583⁄4 45 93⁄4 123⁄16 7 - 960 121 124 643⁄4 51 93⁄4 123⁄16 7 - 972 140 155 763⁄4 63 101⁄8 129⁄16 71⁄2 - 9
1717
Accessories20 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D5-20TA-(BW)B OR D5-20TA-(BW)R 5" DIA ROLL
20 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D6-20TA-(BW)B OR D6-20TA-(BW)R 6"DIA ROLL
35 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D5-35TA-(BW)B OR D5-35TA-(BW)R 5" DIA ROLL
35 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D6-35TA-(BW)B OR D6-35TA-(BW)R 6" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 23/8"
43/4" ± 1/4
61/2" - 9"
33/4"
31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
20°
A
C
EWide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 23/8"
43/4" ± 1/4
61/2" - 9"
33/4"
31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
20°
A
C
EWide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 43/8"43/4" ± 1/4
61/2" - 9"31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
35°
A
C
Wide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 43/8"43/4" ± 1/4
61/2" - 9"31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
35°
A
C
Wide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 96 99 335⁄8 9 813⁄16 145⁄830 106 114 393⁄8 11 813⁄16 155⁄16
36 121 124 451⁄8 13 813⁄16 1642 136 141 507⁄8 15 813⁄16 1611⁄16
48 149 152 565⁄8 17 813⁄16 173⁄854 160 165 627⁄8 19 91⁄8 183⁄860 179 186 685⁄8 21 91⁄8 191⁄16
66 195 198 741⁄4 23 91⁄2 201⁄872 207 210 80 25 91⁄2 2013⁄16
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 98 101 333⁄4 9 813⁄16 163⁄430 108 115 39 11 813⁄16 177⁄836 122 125 445⁄16 13 813⁄16 191⁄16
42 137 143 499⁄16 15 813⁄16 203⁄16
48 150 154 551⁄16 17 813⁄16 215⁄16
54 161 166 609⁄16 19 91⁄8 223⁄460 181 188 661⁄16 21 91⁄8 2315⁄16
66 196 200 715⁄16 23 91⁄2 257⁄16
72 208 212 765⁄8 25 91⁄2 265⁄8
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 104 107 335⁄8 9 95⁄16 145⁄830 116 123 393⁄8 11 95⁄16 155⁄16
36 131 134 451⁄8 13 95⁄16 1642 148 154 507⁄8 15 95⁄16 1611⁄16
48 163 166 565⁄8 17 95⁄16 173⁄854 175 180 627⁄8 19 95⁄8 183⁄860 196 203 685⁄8 21 95⁄8 191⁄16
66 212 216 741⁄4 23 10 201⁄872 225 229 80 25 10 2013⁄16
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 105 108 333⁄4 9 95⁄16 163⁄430 117 124 39 11 95⁄16 177⁄836 132 135 445⁄16 13 95⁄16 191⁄16
42 150 155 499⁄16 15 95⁄16 203⁄16
48 164 168 551⁄16 17 95⁄16 215⁄16
54 177 181 609⁄16 19 95⁄8 223⁄460 197 205 661⁄16 21 95⁄8 2315⁄16
66 214 217 715⁄16 23 10 257⁄16
72 227 231 765⁄8 25 10 265⁄8
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
1818
RETURN SELF-ALIGNING WITH GUIDE ROLLS D5-RA-(BW)B, D5-RA-(BW)R, D6-RA-(BW)B OR D6-RA-(BW)R 5" & 6" DIA ROLL
45 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D5-45TA-(BW)B OR D5-45TA-(BW)R 5" DIA ROLL
Accessories
DISC RETURN SELF-ALIGNING D5-RAD-(BW)B OR D6-RAD-(BW)B 5" & 6" DIA ROLL
45 DEG. TROUGH SELF-ALIGNING WITH GUIDE ROLLS D6-45TA-(BW)B OR D6-45TA-(BW)R 6" DIA ROLL
Belt width +9" for standard baseBelt width +15" for wide base
5/8" dia. bolts5/8"
7/8"
1/4"41/2" Drop
4" - 41/2"
33/4"43/4"
21/4" dia.
6"
12"
A
Wide Base Shown
Belt width
Roll dia.
Standard Base Shown
Belt Travel95/8"11/4"
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 51/2"43/4" ± 1/4
61/2" - 9"31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
45°
A
C
Wide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt width +9" for standard baseBelt width +15" for wide base
5/8" dia. bolts5/8"
7/8"
1/4"41/2" Drop
4" - 41/2"
33/4"43/4"
21/4" dia.
6"
12"
A
Wide Base Shown
Belt width
Roll dia.
Standard Base Shown
Belt Travel95/8"11/4"
Belt width +9" for standard baseBelt width +15" for wide base
1/2" Bolt for 18" - 24" belt5/8" Bolt for 30" - 72" belt
3/8"
Approx. 51/2"43/4" ± 1/4
61/2" - 9"31/4"
21/4" dia.93/4"
10"
B
D ± 1/4
Roll dia.
45°
A
C
Wide Base Shown Standard Base Shown
Belt Travel
11/4"
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 92 95 333⁄16 9 813⁄16 177⁄830 110 115 38 11 813⁄16 191⁄436 121 126 4213⁄16 13 813⁄16 2011⁄16
42 143 148 475⁄8 15 813⁄16 221⁄848 169 174 527⁄16 17 813⁄16 231⁄254 185 190 5711⁄16 19 91⁄8 251⁄460 196 201 625⁄8 21 91⁄8 2611⁄16
66 206 211 679⁄16 23 91⁄2 287⁄16
72 216 221 723⁄8 25 91⁄2 297⁄8
Belt Width
Std.Wt.
Wide Wt.
A B C D
24 94 99 333⁄16 9 95⁄16 177⁄830 113 118 38 11 95⁄16 191⁄436 125 130 4213⁄16 13 95⁄16 2011⁄16
42 148 153 475⁄8 15 95⁄16 221⁄848 175 180 527⁄16 17 95⁄16 231⁄254 187 192 5711⁄16 19 95⁄8 251⁄460 201 206 625⁄8 21 95⁄8 2611⁄16
66 211 216 679⁄16 23 10 287⁄16
72 221 226 723⁄8 25 10 297⁄8
5 Inch Return Trainer with Guide Rolls
Belt Width
Std.Wt.
WideWt. A
24 109 112 2730 120 124 3336 133 136 3942 144 147 4548 159 162 5154 171 174 5760 183 187 6366 196 199 6972 208 211 72
5 Inch Disc ReturnRUBBER
Belt Width
Std.Wt. A
24 89 271⁄830 97 331⁄836 104 391⁄842 115 451⁄848 121 511⁄854 137 571⁄860 144 631⁄872 161 751⁄8
6 Inch Disc ReturnRUBBER
Belt Width
Std.Wt. A
24 92 271⁄830 101 331⁄836 110 391⁄842 120 451⁄848 127 511⁄854 143 571⁄860 151 631⁄872 169 751⁄8
6 Inch Return Trainer with Guide Rolls
Belt Width
Std.Wt.
WideWt. A
24 115 118 2730 129 132 3336 142 145 3942 155 158 4548 171 174 5154 184 188 5760 198 201 6366 212 215 6972 225 228 75
1919
Dimensions in inches. Weights in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.Note: Bolt slots on troughing idlers allow up to 5⁄8" bolt. CEMA allows 1⁄2" bolt through 36" belt width.
Bolt slots on drop hangers allow up to 1⁄2" bolt. For Reverse Belt Conveyors, consult factory.
CEMA D Wobbler Self-Aligning
Available in 6" diameter rolls only. The Wobbler is available with 13⁄8" and 41⁄4" drop brackets as shown above. Add S08709A or M19088A for required drop hangers. Optional 1⁄4" urethane cover also available for sticky material or adverse weather conditions, add U as suffix to part number.
Accessories Ball Bearing
WOBBLER RETURN SELF-ALIGNING D6-RAW-(BW)B
Centerline of pin about whichidler swivels
Slotted holes for 5/8" dia. bolts
1 / 4"
35/8"
7"
6"
A
C
Single hole for 1/2" bolt
Clamp boxS08709A
Clamp boxM19088A
Belt Travel 91/2"
11 / 4" 41 / 4
"
13 / 8"
45°
45°
Belt Width
A C13⁄8"Wt.
41⁄4"Wt.
18 27 20 59 6324 33 26 67 7130 39 32 75 7936 45 38 83 8742 51 44 91 9548 57 50 99 10354 63 56 107 11160 69 62 115 119
Goodman-Hewitt ProductsP.O. Box 866645 Floyd Wright DriveBelton, South Carolina 29627Phone: 800-388-7701 / Fax: 877-233-8092
www.phmining.comwww.minepro.com
Additional conveyor components include:• Pulleys• Impact Roller Beds• Impact Beds• Slide Seal Assemblies• Scale Idlers
What You Want, When You Want It.
XS-5104 3BM-910
All designs, specifications and components of the equipment described above are subject to change at the manufacturer’s sole discretion at any time without advance notice. Data published herein is informational in nature and shall not be construed to warranty the suitability of the equipment for any particular purpose as performance may vary with the conditions encountered. The only warranty applicable is our standard written warranty for this equipment.
P&H, P&H MinePro Services and Goodman-Hewitt are trademarks of Joy Global Inc. or one of its affiliates. © 2010 P&H Mining Equipment Inc. All rights reserved.
Goodman-Hewitt spiral idlers are designed to perform in even the stickiest applications. Their unique “corkscrew” design works to clean the conveyor belt and helps to control belt-training problems associated with installations handling sticky material. Spiral idlers are available in belt widths from 18" to 48".
P&H MinePro Services1-888-MINEPROOutside the U.S. and CanadaPhone: (414) 671-4400Fax: (414) 670-7306
www.phmining.comwww.minepro.com