Verizon Wireless LTE 3GPP Band 13

Technical Test Entrance Criteria Version 3.6

IMPORTANT – PLEASE READ

This Document Has Following Sections:

Revision HistoryDevice Test Plan - A list of required test based on information provided by UE OEMTest UE IMEI -- A list of IMEI's for test UEs Submission Items - Items & documentation reuired to be sent to Verizon Wireless in the "submission."LTE 13 RF and RRM - Test cases to be executedLTE Supplementary RF - Test cases to be executedLTE Supplementary Signaling - Test cases to be executedLTE Sig 36.523-1- Test cases to be executedLTE OTA Radiated - Test cases to be executedLTE Data Retry - Test cases to be executedLTE Device-UICC (USIM, ISIM) - Test cases to be executedLTE SMS - Test cases to be executedLTE Data Throughput - Test cases to be executedLTE IMS RegistraionAT+ Cmmds-AT commands the device is required to exectueLTE IOT "Credit"-Test cases to be executed if "Certified Chipset" employed

Required Manual selectionValidated test caseSection header (not a test case)

This document provides initial information related to the Verizon WirelessTest Entrance Criteria. All information herein is subject to change without notice. The information provided was considered technically accurate at the time the documents were developed, but Verizon Wireless disclaims and makes no guaranty or warranty, express or implied, as to the accuracy or completeness of any information contained or referenced herein. VERIZON WIRELESS DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Verizon Wireless is not providing any license necessary to access or utilize any source materials referenced herein. It shall be the responsibility of the developer to obtain any such licenses, if necessary.

The developer of any device, service or product for use on the Verizon Wireless network assumes all risks related to the development of such device, service or product. Verizon Wireless does not guarantee or warrant the availability of its network or the compatibility of its network with any device, service or product. Verizon Wireless disclaims liability for any damages or losses of any nature whatsoever whether direct, indirect, special or consequential resulting from the use of or reliance on any information contained or referenced herein.

This publication is part of Verizon Wireless’ compliance with the FCC’s rules for 700 MHz C Block (47 C.F.R. § 27.16), as explained in the FCC’s Second Report and Order in WT Docket No. 06-150, “Service Rules for the 698-746, 747-762 and 777-792 MHz Bands” released on August 10, 2007.

The purpose of this document is to provide LTE test labs with information for generating appropriate test campaign for a given UE.

Document Guide - This sheet

Revision HistoryEdited by Version Number Worksheet Item Date Verizon Wireless 1.0 Entire Workbook Initial issue of document N/AVerizon Wireless 2.0 Entire Workbook Interim development, not released N/AVerizon Wireless 3.0 Entire Workbook Incorporation of GCF 3.49.0; Incorporation of Test Case List 3.2 25 Feb 2013

Verizon Wireless 3.1 14 May 2013

L. Conzo 3.2 31 July 2013

L. Conzo 3.3 30 Sep 2013

R. Yan 3.4 10, April 2014

3.5 11 Nov, 2014

3.5.1 4 Mar, 2015

3.6 10 Aug, 2015

Entire Document; Corrected SFN/CCP omission. Device Test Plan; change Band 4 portion of Domestic FIT Test Lab to "VZW NDET Lab"; add RF testing to "Location Change'; add "Chipset Conformance to "LTE Test Type", add "Chipset Conformance to "CDMA Test Type", add "N/A" to "Operating System", add "Chipset test Platform" to "Form Factor", add "N/A" to "LTE Band 13 certified Chipset(CCP)", "Motive IOT" not required for "Chipset test Platform", removed "CDMA from "Other CDMA Test Plans" label, Global Device drop-down, "Yes" changed to "Global", Added B4 GCF RF Conformance to B4 SFN, Added B4 RF Supplimental to B4 SFN, Added B4 GCF Sig Conformance to B4 SFN; B4 Interband Test Plan to be performed at VZW NDET Lab; LTE-CDMA iRAT Performance test Plan changed to "VZW NDET Lab" "Submission Items": Removed UTS Driver requirement, Added "Network Extender Visual Indicator test results (Handset only)". LTE Data Retry; Added TC 5.5- 5.9, 6.7-6.16 & 7.3. ; LTE IMS Reg & Retry, removed TC 2.19 & 2.24. LTE Device-UICC (USIM, ISIM); 3.16 - 3.18 "not required", add 'GCF disclamer'. Device test P[lan; disable all Band for except for "N/A" and "B4 OFF at launch".

Entire Workbook; Updated to Test Case List v3.3 ans GCF 3.50.1Device Test Plan; Change 'Device Conformance' to 'Lab Conformance'; LTE Supplementary RRM Test Plan Added, removed "only" from "LTE device Capability"; struck NBPCDT Test Plan; struck "LTE Multi-Mode SMS Test Plan"; GPAC Testis Plann added; changed "Wi-Fi Performance Test Plan" to "Compliance / Performance Test Plan for Wi-Fi"; added "Data Retry for LTE Multi-Mode Devices", added SVD Interband Test Plan ; added "LTE 3GPP Band 13 Supplementary RRM Conformance" Test Plan & Test casesLTE Supplementary RRM Test Plan Worksheet addedLTE Data Retry; Add TCs 4.10, 4.11, 4.12, 4.13, 5.13, 5.14, 5.15, 5.16, 6.17, 6.18, 6.19, 6.20LTE Supp Sig; Add TCs 2.31, 2.32, 2.33, 2.34, 2.35, 2.36AT+Cmmds; VOID TC 2.45, 3.4, 3.5LTE IMS Registration; VOID TC 2.5, 2.10 LTE Supplementary RRM; Worksheet addedLTE-Device-UICC(USIM,ISIM); Add TC 2.20, Aligned closer to current GCF36.521-3; Add TC 4.5.1.1 36.523-2; Add TC 9.2.1.1.26, Remove 9.3.1.12aDocument Guide- Corrected SGS contact information

Entire Worksheet-added "Software Update" Test Cases to automation;Device Test Plan-added "Tech Mahindra" to approved LTE Lab listrename "Visual Indicator Test Plan" to "RSSI Test Plan"; rename "Battery Pre-test results of VZW Accessory Test Plan" to "Accessory_Battery_Charger_TestPlan";rename "VZW Test Plan for Battery Standby Usage" to "DaysOfUseMeasurement_TestPlan"added "Femtocell BNE+VI Test Plan "; added "OEM Selection" column for manual test plan selection;added former Regression Test Plan automation to CDMA portion;corrected the 'switching' for "Over_the_Air_Radiated_performance..."removed "LTE CDMA IRAT Interoperability Test Plan" (it is subsumed in MM IOT)Document Guide-added simple instructions for the SU and Regression automation.

Entire Document-Compliant to Required Case List v3.6. Feb 2014 requirementAdd VoLTE Test PlansCovered tickets assigned to author - DoneAdd banner for GCF Certification Requirement for LTE DevicesDevice Test Plan tab update for the test plans.Revised after initial release of v3.4Updated for B13 LTE Open Access.

S. Patel

Entire Document-Updated formatting for all tabs.Updated test cases as per Oct-2014 Test Plans.Added temperature range option - "-30 to +60".7-Layers Lab contact information has been updated as per 7-layers request.Updated 'LTE Test Type' field - Added 'Location Change' category to 'LTE Test Type' field. Removed unused categories - 'Chipset SFN' and 'Chipset Conformance' from 'LTE Test Type' fields.Removed 'Submission Items' tabRemoved unnecessary fields - VoLTE, GPS, SVLTE, ERI, Global Device, Browser, Band-4, Push-to-Talk, Pre-Pay, Wi-Fi, Near Field Communication

S. Patel

Entire Document-- Changed required test results per test case to 1 for below test plans:LTE 3GPP Band 13 RF and RRM GCF Conformance Test Plan LTE 3GPP Band 13 Supplementary RF Conformance Test Plan LTE 3GPP Band 13 Supplementary RRM Conformance LTE Device-UICC (USIM, ISIM) Interaction Test Plan - LTE B13 Field Test Plan' is replaced with 'GCF Field Test Plan'.- 'LTE OTADM Test Plan' is added in 'Device Test Plan' tab.- Removed 'LTE OTADM' tab.- Updated LTE SFN test scope for 'LTE Device-UICC (USIM, ISIM) Interaction Test Plan' test plan- Updated 'LTE IMS Reg-Retry' tab with certified module testing scope.- 'Required Test Case List' has been retired from Feb-2015. Removed 'Required Test Case List' option from 'Device Test Plan' tab

S. Patel

Entire Document-- Test Cases are updated as per June-2015 Reqs Release.- Document Guide: Updated SGS Lab and Intertek Contact Information.- Updated Temp. range required for RF testing: -10°C, +25°C and +55°C- Test Plan tabs are updated as per latest Test Equipment List.- Updated required testing for Device Using Certified Module.- Updated Intertek Lab contact information. - Added New VZW Approved 3rd Party Lab (for Antenna Testing)- Updated required LTE SFN test scope:LTE signaling test plan (3GPP TS 36.523-1)LTE RF Conformance Test Plan (3GPP TS 36.521-1)LTE 3GPP Band 13 Supplementary RF conformance Test Plan:LTE 3GPP Band 13 Supplementary Signaling Conformance Test Plan:LTE Data Retry Test Plan:LTE IMS Registration and Retry Test Plan

v3.6Open Access - Test Entrance Criteria Checklist

THIS SECTION TO BE COMPLETED BY DEVICE SUPPLIER

Administrative Information Test Selection InformationPreparation Date: LTE Test Type Select

LTE Test Lab Select

Manufacturer / VZWID:LTE Device Capability Select

Model / PrductID:

3GPP Release: Operating System Select

SW Version: Receive Diversity Select

HW Version: Short Message Service Select

Requirements Release Date Enhanced Message Service Select

GCF-CC Version: GCF labs will use the latest revision of GCF-CC Multimedia Message Service Select

GCF Certificate and Test Results are required for all Bands supported by LTE Devices/Modules. Voice / Data SelectSelect

Form Factor Select N/ALTE Field Test Select

Temperature and Voltage testing? Select

Required Temperature Testing: Select No

LRA Participant No B4 ON at Launch

Select

LTE Certified Chipset (CCP)? Select

LTE Document Expiration Date:

Required Testing

LTE 3GPP Band 13 Lab Conformance Test Plans

Selection Test Plan Test lab CommentsSelect

Not Required LTE 3GPP Band 13 RF and RRM GCF Conformance Test Plan 1 LTE Band 13 + CDMANot Required LTE 3GPP Band 13 Supplementary RF Conformance Test Plan 1 LTE Band 13 + CDMA + Other LTE + legacy 3GPPNot Required LTE 3GPP Band 13 Supplementary RRM Conformance 1 LTE + legacy 3GPPNot Required LTE 3GPP Band 13 Signaling GCF Conformance Test Plan 1 LTE Band 13Not Required LTE 3GPP Band 13 Supplementary Signaling Conformance Test Plan 1Not Required LTE Data Retry Test Plan 1Not Required LTE Over the Air Radiated Performance Test Plan Select 1 Select

Not Required LTE Device-UICC (USIM, ISIM) Interaction Test Plan 1

Not Required LTE SMS Test Plan 1

Not Required LTE AT Commands for Test Automation Test Plan 1Not Required LTE Data Throughput Test Plan 1

TECC VZW Point of Contact:(For VZW NDET USE ONLY)

RRC UE Feature Group Support (provide a comma separated list of supported features e.g, 2, 4, 5, etc) -- see 3GPP TS 36.331 section B1 for feature group definition

VzW Certified Module ?(Contact NDET Lab-DTO, if applicable)

Note: Testing has to begin before this document expires. Once this document expires a new test release number and requirements will be applied to this device.

Regression and Software Update Manual SelectionNote: Review respective worksheet(if available) for proper selection, if manually selected 'Required' in 'VZW'/'OEM'

selection.

Number of Required Test Results (with different ID's)

VZW Selection

OEM Selection

7 layers Inc.

Note - a. If the IMS Client supporting SMS over IMS resides natively in the module, no retest is required in the HOST DEVICE.b. If the IMS Client supporting SMS over IMS does not natively reside in the module, full testing of the LTE Band 13 SMS Test Plan shall be executed on the HOST DEVICE.

Cetecom

Intertek

PCTEST

Not Required LTE IMS Registration and IMS Registration Retry 1

Other LTE 3GPP Band 13 Test PlansN/A

Not Required Select

Not Required LTE OTADM Test Plan 1Not Required Motive IOT Motive Lab 1Not Required LTE 3GPP Band 13 Interoperability Test Plan Alcatel-Lucent 1Not Required LTE 3GPP Band 13 Interoperability Test Plan Ericsson 1

TEST LAB INSTRUCTION!If a more recent GCF test case list is published, it superseeds the one listed in this document.

SGS

GCF Field Test Plan(Note: This test plan replaces the former LTE B13 Field Open Access Test Plan. Tests are to be executed by Verizon Wireless approved RTO.)

1 per test market (Dallas-TX, Irvine-CA)

IMEI Location (City, State)123456789

10111213141516171819202122232425262728293031323334353637383940414243444546474849

5051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899

100101102

103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155

156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208

209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261

262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314

315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367

368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420

421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473

474475476477478479480481482483484485486487488489490491492493494495496497498499500

Reasoning behind LTE SFN Request:

LTE 3GPP Band 13 RF and RRM GCF Conformance Test Plan

Test Case

3GPP TS 36.521-1

Transmitter Characteristics6.2.2 Maximum Output Power6.2.3 Maximum Power Reduction (MPR)6.2.4 Additional Maximum Power Reduction (A-MPR)6.2.5 Configured UE transmitted Output Power6.3 Output Power Dynamics6.3.1.1 Power Control Absolute power tolerance6.3.2 Minimum Output Power6.3.3 Transmission ON/OFF Power6.3.4 ON/OFF time mask6.3.4.1 General ON/OFF time mask6.3.4.2 PRACH and SRS time mask6.3.4.2.1 PRACH time mask6.3.4.2.2 SRS time mask6.3.5 Power Control6.3.5.1 Power Control Absolute power tolerance6.3.5.2 Power Control Relative power tolerance6.3.5.3 Aggregate power control tolerance6.4 Void6.5 Transmit signal quality6.5.1 Frequency Error6.5.2 Transmit modulation6.5.2.1 Error Vector Magnitude (EVM)6.5.2.1A PUSCH-EVM with exclusion period6.5.2.2 IQ-component6.5.2.3 In-band emissions for non allocated RB6.5.2.4 Spectrum flatness6.6 Output RF spectrum emissions6.6.1 Occupied bandwidth6.6.2 Out of band emission6.6.2.1 Spectrum Emission Mask6.6.2.2 Additional Spectrum Emission Mask6.6.2.3 Adjacent Channel Leakage power Ratio6.6.2.4 Additional ACLR requirements6.6.3 Spurious emissions6.6.3.1 Transmitter Spurious emissions

6.6.3.2 Spurious emission band UE co-existence6.6.3.3 Additional spurious emissions6.7 Trensmission Intermodulation6.7 Transmit intermodulation7 Receiver Characteristics7.3 Reference sensitivity level7.4 Maximum input level7.5 Adjacent Channel Selectivity (ACS)7.6 Blocking characteristics7.6.1 In-band blocking7.6.2 Out of-band blocking7.6.3 Narrow band blocking7.7 Spurious response7.8 Intermodulation characteristics7.8.1 Wide band Intermodulation7.8.2 Narrow band Intermodulation

7.9 Spurious emissions7.9 Spurious emissions (Up To 3GHz)

8 Performance Requirement

8.1 General 8.1.1 Dual-antenna receiver capability8.1.1.1

8.1.1.2

8.2 Demodulation of PDSCH (Cell-Specific Reference Symbols)

8.2.1 FDD (Fixed Reference Channel)8.2.1.1

8.2.1.1.1 FDD PDSCH Single Antenna Port Performance8.2.1.1.2 FDD PDSCH Single Antenna Port Performance with 1PRB8.2.1.2

8.2.1.2.1 FDD PDSCH Transmit Diversity 2x28.2.1.2.2 FDD PDSCH Transmit Diversity 4x28.2.1.3

8.2.1.3.1 FDD PDSCH Open Loop Spatial Multiplexing 2x28.2.1.3.2 FDD PDSCH Open Loop Spatial Multiplexing 4x28.2.1.4

8.2.1.4.1

8.2.1.4.2

8.2.2 TDD (Fixed Reference Channel)8.2.2.1

8.2.2.1.1

8.2.2.1.2

FDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)FDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)

FDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)

FDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)

FDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)

FDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2 x 2FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4 x 2

TDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)TDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)TDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)

8.2.2.2

8.2.2.2.1 TDD PDSCH Transmit Diversity 2x28.2.2.2.2 TDD PDSCH Transmit Diversity 4x28.2.2.3

8.2.2.3.1 TDD PDSCH Open Loop Spatial Multiplexing 2x28.2.2.3.2 TDD PDSCH Open Loop Spatial Multiplexing 4x28.2.2.4

8.2.2.4.1

8.2.2.4.2

8.3 Demodulation of PDSCH (User-Specific Reference Symbols)

8.3.1 FDD8.3.1 Demodulation of PDSCH 8.3.2 TDD8.3.2.1 Demodulation of PDSCH8.4 Demodulation of PCFICH/PDCCH8.4.1 FDD8.4.1.1 FDD PCFICH/PDCCH Single-antenna Port Performance8.4.1.2 FDD PCFICH/PDCCH Transmit Diversity Performance8.4.1.2.1 FDD PCFICH/PDCCH Transmit Diversity 2x2 Performance8.4.1.2.2 FDD PCFICH/PDCCH Transmit Diversity 4x2 Performance8.4.2 TDD8.4.2.1 TDD PCFICH/PDCCH Single-antenna Port Performance8.4.2.2 TDD PCFICH/PDCCH Transmit Diversity Performance8.5 Demodulation of PHICH8.5.1 FDD8.5.1.1 FDD PHICH Single-antenna Port Performance8.5.1.2 FDD PHICH Transmit Diversity Performance

8.5.1.2.1 FDD PHICH Transmit Diversity 2x2 Performance8.5.1.2.2 FDD PHICH Transmit Diversity 4x2 Performance8.5.2 TDD8.5.2.1 TDD PHICH Single-antenna Port Performance8.5.2.2 TDD PHICH Transmit Diversity Performance

9 Reporting of Channel State Information9.1 General9.2 CQI Reporting under AWGN conditions9.2.1 CQI Reporting under AWGN conditions - PUCCH 1-09.2.1.1 FDD CQI Reporting under AWGN conditions – PUCCH 1-09.2.1.2 TDD CQI Reporting under AWGN conditions – PUCCH 1-09.2.2 CQI Reporting under AWGN conditions - PUCCH 1-19.2.2.1 FDD CQI Reporting under AWGN conditions – PUCCH 1-19.2.2.2 TDD CQI Reporting under AWGN conditions – PUCCH 1-19.3 CQI Reporting under fading conditions9.3.1 Frequency-selective scheduling mode9.3.1.1 CQI Reporting under fading conditions – PUSCH 3-09.3.1.1.1 FDD CQI Reporting under fading conditions – PUSCH 3-09.3.1.1.2

TDD CQI Reporting under fading conditions – PUSCH 3-0

TDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)

TDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)

TDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2 x 2TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4 x 2

9.3.2 Frequency non-selective scheduling mode9.3.2.1 CQI Reporting under fading conditions – PUCCH 1-09.3.2.1.1 FDD CQI Reporting under fading conditions – PUCCH 1-09.3.2.1.2 TDD CQI Reporting under fading conditions – PUCCH 1-09.3.3 Frequency-selective interference9.3.3.1

9.3.3.1.1

9.3.3.1.2

9.4 Reporting of Precoding Matrix Indicator (PMI)9.4.1 Single PMI9.4.1.1 PMI Reporting – PUSCH 3-1 (Single PMI)9.4.1.1.1 FDD PMI Reporting – PUSCH 3-1 (Single PMI)9.4.1.1.2 TDD PMI Reporting – PUSCH 3-1 (Single PMI)9.4.2 Multiple PMI9.4.2.1 PMI Reporting – PUSCH 1-2 (Multiple PMI)9.4.2.1.1 FDD PMI Reporting – PUSCH 1-2 (Multiple PMI)9.4.2.1.2 TDD PMI Reporting – PUSCH 1-2 (Multiple PMI)9.5 Reporting of Rank Indicator (RI)9.5.1 RI Reporting – PUCCH 1-19.5.1.1 FDD RI Reporting– PUCCH 1-19.5.1.2 TDD RI Reporting – PUCCH 1-1

3GPP TS 36.521-3E-UTRAN RRC_IDLE State Mobility4.2.1 E-UTRAN FDD – FDD cell re-selection intra frequency case

4.2.2 E-UTRAN TDD – TDD cell re-selection intra frequency case

4.2.3 E-UTRAN FDD – FDD cell re-selection inter frequency case

4.2.4 E-UTRAN FDD – TDD cell re-selection inter frequency case

4.2.5 E-UTRAN TDD – FDD cell re-selection inter frequency case

4.2.6 E-UTRAN TDD – TDD cell re-selection inter frequency case

4.3.1.1

4.3.1.2

4.3.1.3

4.3.2 E-UTRAN FDD – UTRAN TDD cell re-selection4.3.3 E-UTRAN TDD – UTRAN FDD cell re-selection4.3.4.1

4.3.4.2

4.4.1 E-UTRAN FDD – GSM cell re-selection

CQI Reporting under fading conditions and frequency-selective interference – PUSCH 3-0

FDD CQI Reporting under fading conditions and frequency-selective interference – PUSCH 3-0TDD CQI Reporting under fading conditions and frequency-selective interference – PUSCH 3-0

E-UTRA FDD-UTRAN FDD cell reselection: UTRA FDD is of higher priorityE-UTRAN FDD – UTRAN FDD cell re-selection: UTRA FDD is of lower priorityE-UTRAN FDD – UTRAN FDD cell re-selection in fading propagation conditions: UTRA FDD is of lower priority

E-UTRA TDD-UTRAN TDD cell re-selection : UTRA is of higher priorityE-UTRAN TDD – UTRAN TDD cell re-selection: UTRA is of lower priority

4.4.2 E-UTRAN TDD – GSM cell re-selection4.5.1.1

4.6.1.1 E-UTRAN FDD – cdma2000 1xRTT Cell re-selection

E-UTRAN RRC_CONNECTED State Mobility5.1.1 E-UTRAN FDD-FDD Handover intra frequency case5.1.2 E-UTRAN TDD-TDD Handover intra frequency case5.1.3 E-UTRAN FDD-FDD Handover inter frequency case5.1.4 E-UTRAN TDD-TDD Handover inter frequency case5.1.5

5.1.6 E-UTRAN TDD-TDD Handover inter frequency case5.2.1 E-UTRAN FDD – UTRAN FDD handover5.2.2 E-UTRAN TDD – UTRAN FDD handover5.2.3 E-UTRAN FDD – GSM handover5.2.4 E-UTRAN TDD – UTRAN TDD handover5.2.5 E-UTRAN FDD – UTRAN TDD handover5.2.6 E-UTRA TDD – GSM handover5.2.7

E-UTRAN FDD – UTRAN FDD handover: unknown target cell5.2.8 E-UTRAN FDD – GSM handover: unknown target cell5.2.9 E-UTRAN TDD – GSM handover unknown target cell5.2.9

E-UTRAN TDD – UTRAN TDD handover:unknown target cell5.3.1 E-UTRAN FDD Intra-frequency RRC Re-establishment5.3.2 E-UTRAN FDD Intra-frequency RRC Re-establishment5.3.2 E-UTRAN TDD Intra-frequency RRC Re-establishment5.3.2 E-UTRAN TDD Inter-frequency RRC Re-establishmentRRC Connection Mobility Control6.1.1 E-UTRAN FDD Intra-frequency RRC Re-establishment6.1.2 E-UTRAN FDD Intra-frequency RRC Re-establishment6.1.3 E-UTRAN TDD Intra-frequency RRC Re-establishment6.1.4 E-UTRAN TDD Inter-frequency RRC Re-establishment6.2.1 E-UTRAN FDD – Contention Based Random Access Test6.2.2

E-UTRAN FDD – Non-Contention Based Random Access Test6.2.3 E-UTRAN TDD – Contention Based Random Access Test6.2.4

E-UTRAN TDD – Non-Contention Based Random Access TestTiming and Signalling Characteristics7.1.1 E-UTRAN FDD – UE Transmit Timing Accuracy7.1.2 E-UTRAN TDD – UE Transmit Timing Accuracy7.2.1 E-UTRAN FDD – UE Timing Advance Adjustment Accuracy7.2.2 E-UTRAN TDD – UE Timing Advance Adjustment Accuracy7.3.1 E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync7.3.2 E-UTRAN FDD Radio Link Monitoring Test for In-sync7.3.3 E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync7.3.4 E-UTRAN TDD Radio Link Monitoring Test for In-sync7.3.5

7.3.6E-UTRAN FDD Radio Link Monitoring Test for In-sync in DRX

E-UTRAN FDD – HRPD Cell Reselection: HRPD is of Lower Priority

E-UTRAN TDD-TDD inter frequency handover: unknown target cell

E-UTRAN FDD Radio Link Monitoring Test for Out-of-sync in DRX

7.3.7

7.3.8E-UTRAN TDD Radio Link Monitoring Test for In-sync in DRX

UE Measurements Procedures8.1.1

8.1.2

8.1.3

8.1.4

8.1.5

8.1.6

8.2.1

8.2.2

8.3.1

8.3.2

8.4.1

8.4.2

8.5.1

8.5.2

8.5.3

8.6.1

8.7.1

8.7.2

8.7.3

8.8.1 E-UTRAN FDD – GSM event triggered reporting in AWGN

E-UTRAN TDD Radio Link Monitoring Test for Out-of-sync in DRX

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in asynchronous cells

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in synchronous cells

E-UTRAN FDD-FDD intra frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX

E-UTRAN FDD-FDD Intra-frequency event triggered reporting under AWGN propagation conditions in asynchronous cells with DRX when L3 filtering is usedE-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps

E-UTRAN FDD - FDD Intra-frequency identification of a new CGI of E-UTRA cell using autonomous gaps with DRX

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells

E-UTRAN TDD-TDD intra-frequency event triggered reporting under fading propagation conditions in synchronous cells with DRX

E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions in asynchronous cells

E-UTRAN FDD-FDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in asynchronous cells

E-UTRAN TDD-TDD Inter-frequency event triggered reporting under fading propagation conditions in synchronous cells

E-UTRAN TDD-TDD Inter-frequency event triggered reporting when DRX is used under fading propagation conditions in synchronous cellsE-UTRAN FDD – UTRAN FDD event triggered reporting under fading propagation conditionsE-UTRAN FDD - UTRAN FDD SON ANR cell search reporting under AWGN propagation conditionsE-UTRAN FDD – UTRAN FDD event triggered reporting when DRX is used under fading propagation conditionsE-UTRAN TDD – UTRAN FDD event triggered reporting under fading propagation conditionsE-UTRAN TDD – UTRAN TDD event triggered reporting under fading propagation conditionsE-UTRAN TDD – UTRAN TDD cell search when DRX is used under fading propagation conditionsE-UTRAN TDD - UTRAN TDD SON ANR cell search reporting under AWGN propagation conditions

8.8.2

8.9.1

8.10.1 E-UTRAN TDD – GSM event triggered reporting in AWGN8.10.2

8.11.1

8.11.2

8.11.3 Void8.11.4

Measurement Performance Requirements9.1.1.1 FDD Intra Frequency Absolute RSRP Accuracy9.1.1.2 FDD Intra Frequency Relative Accuracy of RSRP9.1.2.1 FDD Inter Frequency Absolute RSRP Accuracy9.1.2.2 FDD Inter Frequency Relative Accuracy of RSRP9.1.3.1 FDD - FDD Inter Frequency Absolute RSRP Accuracy9.1.3.2 FDD - FDD Inter Frequency Relative Accuracy of RSRP9.1.4.1 TDD – TDD Inter Frequency Absolute RSRP Accuracy9.1.4.2 TDD - TDD Inter Frequency Relative Accuracy of RSRP9.2.1.1 FDD Intra Frequency Absolute RSRQ Accuracy9.2.2.1 TDD Intra Frequency Absolute RSRQ Accuracy9.2.3.1 FDD – FDD Inter Frequency Absolute RSRQ Accuracy9.2.3.2 FDD – FDD Inter Frequency Relative Accuracy of RSRQ9.2.4.1 TDD Inter Frequency Absolute RSRQ Accuracy9.2.4.2 TDD Inter Frequency Relative Accuracy of RSRQ

E-UTRAN FDD – GSM event triggered reporting when DRX is used in AWGNE-UTRAN FDD – UTRAN TDD event triggered reporting under fading propagation conditions

E-UTRAN TDD-GSM event triggered reporting when DRX is used in AWGNMultiple E-UTRAN FDD-FDD Inter-frequency event triggered reporting under fading propagation conditions

E-UTRAN TDD – E-UTRAN TDD and E-UTRAN TDD Inter-frequency event triggered reporting under fading propagation conditions

InterRAT E-UTRA TDD to E-UTRA TDD and UTRA TDD cell search

LTE 3GPP Band 13 RF and RRM GCF Conformance Test Plan

Selection

Lab ConformanceRegression Test Cases

X

X

X X

XXX

X

XXX X

X

LTE GCF Testing is required with Latest Test Case List (www.globalcertificationforum.org)

LTE SFNTest Cases

Execute Test Cases from Latest GCF Test Case List

X

X

X

X

LTE 3GPP Band 13 RF and RRM GCF Conformance Test Plan

Comments

LTE GCF Testing is required with Latest Test Case List (www.globalcertificationforum.org)

LTE 3GPP Band 13 Supplementary RF Conformance Test Plan

Test Case

Transmitter Tests2.1 Maximum Output Power – No MPR Or A-MPR2.2 Maximum Output Power – With MPR2.3 Transmitter Spectrum Emission Mask (NS_06)2.4 Spurious Emission Band UE Co-Existence2.5 NS_07 SPURIOUS EMISSIONS2.5.2 UE Maximum Output Power with Additional Requirements (A-MPR)2.5.3 Additional Spurious Emissions2.6 TRANSMITTER LO AND IMAGE SUPPRESSION (IQ COMPONENT AND IMAGE)2.6.2 LO Leakage (i.e. IQ Component)2.6.3 Image Suppression (i.e. In-Band Emissions for Non-Allocated RB)2.7 PUCCH Over-Provisioning Functional Test2.8 Configured Output Power2.9 Spurious Emissions With TX GatingReceiver Tests3.1 Reference Sensitivity – Dual Receiver (QPSK)3.2 REFERENCE SENSITIVITY – SINGLE RECEIVER 3.2.2 Primary Receiver3.2.3 Secondary/MIMO Receiver3.3 Receiver Blocking3.4 Receiver Intermodulation Characteristics3.5 feICIC GCF RF Conformance Test Cases3.6 DL CoMP GCF RF Conformance Test CasesEnvironmental Tests

4.1 RF PERFORMANCE OVER TEMPERATURE AND VOLTAGE: -10°C, +25°C and +55°C

LTE 3GPP Band 13 Supplementary RF Conformance Test Plan

Selection

Lab Conformance LTE SFN

X X XX XXX X X

X XX X X

XXXXX

X X

X XX XX XX X

X

RegressionTest Cases

LTE 3GPP Band 13 Supplementary RF Conformance Test Plan

Selection

X

X

Required Test Cases for Device using Certified

Module

LTE 3GPP Band 13 Supplementary RRM Conformance

Test Case Selection

Lab Conformance

2 Measurement Performance Tests

2.1 RSRP Intra-Frequency Accuracy in RRC_CONNECTED Mode

2.1.2.1 Test 1 X2.1.2.2 Test 2 X2.1.2.3 Test 3 X2.1.2.4 Test 4 X2.2 RSRP Intra-Frequency Accuracy in RRC_IDLE Mode2.2.2.1 Test 1 X2.2.2.2 Test 2 X2.2.2.3 Test 3 X2.2.2.4 Test 4 X2.3 RSRQ Intra-Frequency Accuracy in RRC_CONNECTED Mode2.3.2.1 Test 1 X2.3.2.2 Test 2 X2.3.2.3 Test 3 X2.3.2.4 Test 4 X2.4 RSRQ Intra-Frequency Accuracy in RRC_IDLE Mode2.4.2.1 Test 1 X2.4.2.2 Test 2 X2.4.2.3 Test 3 X2.4.2.4. Test 4 X

2.5 2.5 feICIC GCF RRM Conformance Test Cases 2.6 2.6 feICIC Idle Mode Qoffset support

2.7

2.8 2.8 feICIC UE Handover Range Extension (10MHz BW)

2.9.

2.10

2.11

2.12

2.7 feICIC UE Resets measSubframePcell at RRC Connection Re-establish

2.9 feICIC RSRP INTRA-FREQUENCY ACCURACY IN RRC_CONNECTED MODE 2.10 feICIC RSRQ INTRA-FREQUENCY ACCURACY IN RRC_CONNECTED MODE2.11 feICIC PBCH INTERFERENCE CANCELLATION PERFORMANCE2.12 Intra-Frequency RSRP and RSRQ Accuracy Test while CRS-AssistanceInfoList-r11 is Present

LTE 3GPP Band 13 Supplementary RRM Conformance

Selection Comments

Regression Test Cases

LTE 3GPP Band 13 Signaling GCF Conformance Test Plan

Test Case

3GPP TS 36.523-1

6.1.1.16.1.1.1b6.1.1.2

6.1.1.2a

6.1.1.3 Cell reselection of ePLMN in manual mode6.1.1.3b

6.1.1.4

6.1.1.6

6.1.1.6a

6.1.2 Cell Reselection6.1.2.1 Cell selection / Forbidden tracking area6.1.2.26.1.2.3

6.1.2.4 Cell reselection6.1.2.5 Cell reselection for interband operation6.1.2.66.1.2.7 Cell reselection / Equivalent PLMN6.1.2.7a

Cell reselection / Equivalent PLMN / Single Frequency operation6.1.2.8

6.1.2.8a

6.1.2.9

PLMN selection of RPLMN, HPLMN/EHPLMN, UPLMN and OPLMN / Automatic modePLMN selection of RPLMN, HPLMN/EHPLMN, UPLMN and OPLMN / Automatic mode / Single Frequency operationPLMN selection of "Other PLMN/access technology combinations" / Automatic modePLMN selection of "Other PLMN/access technology combinations" / Automatic mode / Single Frequency operation

Cell reselection of ePLMN in manual mode / Single Frequency operation

PLMN selection in shared network environment / Automatic modePLMN selection of RPLMN, HPLMN/EHPLMN, UPLMN and OPLMN / Automatic mode / User reselection

PLMN selection of RPLMN, HPLMN/EHPLMN, UPLMN and OPLMN / Automatic mode / User reselection / Single Frequency operation

Cell selection / Qrxlevmin

Cell selection / Intra E-UTRAN / Serving cell becomes non-suitable (S<0 or barred)

Cell reselection using Qhyst, Qoffset and Treselection

Cell reselection using cell status and cell reservations / Access control class 0 to 9Cell reselection using cell status and cell reservations / Access control class 0 to 9 / Single Frequency operationCell reselection using cell status and cell reservations / Access control class 11 to15

6.1.2.9a

6.1.2.10 Cell reselection in shared network environment6.1.2.11 Inter-frequency cell reselection6.1.2.12

6.1.2.136.1.2.14 Speed-dependent cell reselection6.1.2.15

6.2 Multi mode environment (E-UTRAN /UTRAN/GERAN/CDMA2000)6.2.1 Inter-RAT PLMN selection 6.2.1.1

6.2.1.2

6.2.1.3

6.2.1.4

6.2.1.5

6.2.2 Inter-RAT Cell Selection6.2.2.1

6.2.2.2

6.2.2.3

6.2.2.4

6.2.2.5 Cell selection / No USIM6.2.2.6

6.2.2.7

6.2.3 Inter-RAT cell reselection6.2.3.1

6.2.3.2

6.2.3.3

6.2.3.4

6.2.3.5

6.2.3.6

Cell reselection using cell status and cell reservations / Access control class 11 to 15 / Single Frequency operation

Cell reselection / Cell-specific reselection parameters provided by the network in a neighbouring cell listCell re-selection, Sintrasearch, Snonintraintersearch

Inter-frequency cell reselection according to cell reselection priority provided by SIBs

Inter-RAT PLMN selection / Selection of correct RAT for OPLMN / Automatic mode

Inter-RAT PLMN selection / Selection of correct RAT for UPLMN / Automatic modeInter-RAT PLMN selection / Selection of correct PLMN and RAT in shared network environment / Automatic modeInter-RAT PLMN selection / selection of correct RAT from the OPLMN list / Manual mode

Inter-RAT background HPLMN search / Search for correct RAT for HPLMN / Manual Mode

Inter-RAT cell selection / From E-UTRA RRC_IDLE to UTRA_Idle / Serving cell becomes non-suitableInter-RAT cell selection / From E-UTRA RRC_IDLE to GSM_Idle/GPRS Packet_idle / Serving cell becomes non-suitable

Inter-RAT cell selection / From E-UTRA RRC_IDLE to HRPD Idle / Serving cell becomes non-suitableInter-RAT cell selection / From E-UTRA RRC_IDLE to 1xRTT idle / Serving cell becomes non-suitable

Inter-RAT Cell selection / From GSM_Idle/GPRS Packet_idle to E-UTRA RRC_IDLE / Serving cell becomes non-suitable

Inter-RAT Cell selection / From GSM_Idle/GPRS Packet_idle to E-UTRA_RRC_IDLE / Serving cell is barred

Inter-RAT cell reselection / From E-UTRA RRC_IDLE to GSM_Idle/GPRS Packet_IdleInter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRAInter-RAT cell reselection / From UTRA_Idle to E-UTRA RRC_IDLEInter-RAT cell reselection / From UTRA CELL_PCH state to E-UTRA RRC_IDLEInter-RAT cell reselection / From E-UTRA RRC_IDLE to UTRA_IdleInter-RAT cell reselection / From E-UTRA RRC_IDLE to UTRA_Idle according to RAT priority provided by dedicated signalling

6.2.3.7

6.2.3.8

6.2.3.9

6.2.3.10

6.2.3.11

6.2.3.12

6.2.3.13

6.2.3.14

6.2.3.15

6.2.3.16

6.2.3.17

6.2.3.18

6.2.3.19 Redirection to E-UTRA upon the release of the CS connection

6.2.3.20

6.2.3.21

6.2.3.22

6.2.3.23

6.2.3.24

6.2.3.26

6.2.3.27

6.2.3.28

6.2.3.29

6.2.3.30

Inter-RAT cell reselection / From E-UTRA RRC_IDLE to HRPD Idle / HRPD cell is higher reselection priority than E-UTRA

Inter-RAT cell reselection / From E-UTRA RRC_IDLE to HRPD Idle / HRPD cell is lower reselection priority than E-UTRA

Inter-RAT cell reselection / From E-UTRA RRC_IDLE to CDMA2000 Idle when 1xRTT cell is higher reselection priority than E-UTRA

Inter-RAT cell reselection / From E-UTRA RRC_IDLE to CDMA2000 idle / 1xRTT cell is lower reselection priority than E-UTRA

Inter-RAT cell reselection / From HRPD Idle to E-UTRA RRC_IDLEInter-RAT cell reselection / From 1xRTT Dormant to E-UTRA RRC_IDLEInter-RAT cell reselection / From UTRA_Idle to E-UTRA RRC_IDLE according to RAT priority provided by dedicated signalling

Inter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA / Priority of E-UTRA cells are higher than the serving cell

Inter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA / Priority of E-UTRA cells are lower than the serving cell

Inter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA / based on H PRIOInter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA / Priority E-UTRA cellsInter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA / Blacklisted E-UTRA cells

Redirection to E-UTRA upon the release of the CS connection and no suitable cell available Inter-RAT cell reselection / From GPRS Packet_Transfer (NC0 mode) to E-UTRA Inter-RAT Cell Reselection Failure / from GPRS Packet_Transfer (NC0 mode) to E-UTRAInter-RAT cell reselection from GPRS Packet_Transfer to E-UTRA in CCN mode / PACKET CELL CHANGE CONTINUE

Inter-RAT cell reselection from GPRS Packet_transfer to E-UTRA in CCN mode / PACKET CELL CHANGE ORDER

Inter-RAT autonomous cell reselection GPRS Packet_Transfer NC1 mode to E-UTRA CellInter-RAT cell selection / from GPRS Packet_Transfer to E-UTRA cellInter-RAT cell reselection from GPRS Packet_Transfer to E-UTRA / Network assisted cell changeInter-RAT Cell Reselection from GPRS Packet_transfer NC1 mode to E-UTRA / Network assisted cell changeInter-RAT cell reselection failure from GPRS Packet_Transfer to E-UTRA / Network assisted cell change

6.2.3.31

6.2.3.32

6.3 Closed Subscriber Group Cells6.3.1

6.3.2

6.3.3

6.3.4

6.3.5 Manual support for CSG ID selection6.3.6

6.3.7

6.3.8

7 Layer 27.1 MAC7.1.1 Mapping between logical channels and transport channels7.1.1.1

7.1.1.2

7.1.2 RACH 7.1.2.1

7.1.2.2

7.1.2.3

7.1.2.4 Random access procedure / Successful 7.1.2.5

7.1.2.6 Maintenance of uplink time alignment7.1.2.7 MAC contention resolution / Temporary C-RNTI7.1.2.8 MAC contention resolution / C-RNTI7.1.2.9 MAC backoff indicator7.1.3 DL-SCH data transfer7.1.3.1 Correct handling of DL assignment / Dynamic case 7.1.3.2 Correct handling of DL assignment / Semi-persistent case

7.1.3.3 MAC PDU header handling7.1.3.4 Correct HARQ process handling / DCCH and DTCH7.1.3.5 Correct HARQ process handling / CCCH7.1.3.6 Correct HARQ process handling / BCCH

Inter-RAT cell reselection / From UTRA_Idle (low priority) to E-UTRA RRC_IDLE (high priority) according to RAT priority provided by dedicated signalling

Inter-RAT cell re-selection / From E-UTRA RRC_IDLE to UTRA_Idle, Snonintrasearch

Inter-frequency cell reselection / From E-UTRA RRC_IDLE non-CSG cell to E-UTRA RRC_IDLE CSG cellInter-RAT cell reselection / From GSM_Idle/GPRS Packet_Idle to E-UTRA idle CSG cellInter-RAT cell reselection / From UTRA_Idle to E-UTRA RRC_IDLE CSG cell

Inter-RAT cell reselection / From UTRA CELL_PCH state to E-UTRA RRC_IDLE CSG cell

Ignoring CSG cells in cell selection/reselection when allowed CSG list is empty or not supportedInter-RAT Cell reselection from E-UTRA idle non-CSG cell to a UTRA CSG celInter-RAT CSG Cell Reselection from E-UTRA CSG cell to UTRA CSG cell

CCCH mapped to UL SCH/DL-SCH / Reserved Logical Channel IDDTCH or DCCH mapped to UL SCH/DL-SCH / Reserved Logical Channel ID

Correct selection of RACH parameters / Random access preamble and PRACH resource explicitly signalled to the UE by RRC / Non-contention based random access procedure

Correct selection of RACH parameters / Random access preamble and PRACH resource explicitly signalled to the UE in PDCCH Order / Non-contention based random access procedure

Correct selection of RACH parameters / Preamble selected by MAC itself / Contention based random access procedure

Random access procedure / MAC PDU containing multiple RARs

7.1.3.7 MAC padding 7.1.3.9 MAC reset DL7.1.4 UL-SCH data transfer7.1.4.1 Correct handling of UL assignment / Dynamic case7.1.4.2 Correct handling of UL assignment / Semi-persistent case

7.1.4.3 Logical channel prioritization handling7.1.4.4

7.1.4.5

7.1.4.6

7.1.4.7

7.1.4.7a Correct handling of UL assignment / Semi persistent case

7.1.4.8

7.1.4.10 MAC padding 7.1.4.11 Correct HARQ process handling7.1.4.12 MAC reset / UL 7.1.4.13 MAC PDU header handling7.1.4.14 Correct HARQ process handling / TTI Bundling7.1.4.15 UE power headroom reporting / Periodic reporting7.1.4.16

UE power headroom reporting / DL pathloss change reporting7.1.5 PUSCH Hopping7.1.5.1 Inter-TTI PUSCH hopping by uplink grant7.1.5.2 Predefined intra-TTI PUSCH hopping (N_sb=1)7.1.5.3 Predefined intra-TTI PUSCH hopping (N_sb=2/3/4)7.1.5.4 Predefined inter-TTI PUSCH hopping (N_sb=1)7.1.5.5 Predefined inter-TTI PUSCH hopping (N_sb=2/3/4)7.1.6 DRX Operation 7.1.6.1

7.1.6.2

7.1.7 Transport block size selection7.1.7.1 DL-SCH transport block size selection7.1.7.1.1 DL-SCH transport block size selection / DCI format 1 / RA type 0

7.1.7.1.2 DL-SCH transport block size selection / DCI format 1 / RA type 1

7.1.7.1.3

7.1.7.1.4

7.1.7.1.5

7.1.7.1.6

Correct handling of MAC control information / Scheduling requests and PUCCHCorrect handling of MAC control information / Scheduling requests and random access procedureCorrect handling of MAC control information / Buffer status / UL data arrive in the UE Tx buffer and retransmission of BSR / Regular BSR

Correct handling of MAC control information / Buffer status / UL resources are allocated / Padding BSR

Correct handling of MAC control information / Buffer status / Periodic BSR timer expires

DRX Operation / Short cycle not configured / Parameters configured by RRCDRX Operation / Short cycle not configured / DRX Command MAC control element reception

DL-SCH transport block size selection / DCI format 1A / RA type 2 / Localised VRBDL-SCH transport block size selection / DCI format 1A / RA type 2 / Distributed VRBDL-SCH transport block size selection / DCI format 2A / RA type 0 / Two transport blocks enabled / Transport block to codeword swap flag value set to 0

DL-SCH transport block size selection / DCI format 2A / RA type 1/ Two transport blocks enabled / Transport block to codeword swap flag value set to 1

7.1.7.2 UL-SCH transport block size support7.1.7.2.1 UL-SCH transport block size selection / DCI format 07.1.8 Reporting of Rank Indicator (RI)7.1.8.1

7.2 RLC 7.2.2 Unacknowledged mode7.2.2.1

7.2.2.2

7.2.2.3 UM RLC / Reassembly / 5-bit SN / LI value > PDU size7.2.2.4 UM RLC / Reassembly / 10-bit SN / LI value > PDU size7.2.2.5.1 UM RLC / 5-bit SN / Correct use of sequence numbering 7.2.2.5.2 UM RLC / 10-bit SN / Correct use of sequence numbering7.2.2.6 UM RLC / Concatenation, segmentation and reassembly7.2.2.7

7.2.2.8

7.2.2.9

7.2.2.10 UM RLC / Duplicate detection of RLC PDUs7.2.2.117.2.3 Acknowledged mode7.2.3.1 AM RLC / Concatenation and reassembly7.2.3.2

7.2.3.3 AM RLC / Segmentation and reassembly / Framing Info Field

7.2.3.4

7.2.3.5 AM RLC / Reassembly / LI value > PDU size7.2.3.6 AM RLC / Correct use of sequence numbering7.2.3.7 AM RLC / Control of transmit window7.2.3.8 AM RLC / Control of receive window7.2.3.9 AM RLC / Polling for status7.2.3.10 AM RLC / Receiver status triggers7.2.3.13 AM RLC / Reconfiguration of RLC parameters by upper layers

7.2.3.14 AM RLC / In sequence delivery of upper layers PDUs7.2.3.15 AM RLC / Re-ordering of RLC PDU segments7.2.3.16 AM RLC / Re-transmission of RLC PDU without re-segmentation

7.2.3.17 AM RLC / Re-segmentation RLC PDU / SO, FI, LSF7.2.3.18

7.2.3.20 AM RLC / Duplicate detection of RLC PDUs7.2.3.21

7.3 PDCP

Periodic RI reporting using PUCCH / Category 1 UE / Transmission mode 3/4

UM RLC / Segmentation and reassembly / 5-bit SN / Framing info fieldUM RLC / Segmentation and reassembly / 10-bit SN / Framing info field

UM RLC / In sequence delivery of upper layer PDUs without residual loss of RLC PDUs / Maximum re-ordering delay below t-Reordering

UM RLC / In sequence delivery of upper layer PDUs without residual loss of RLC PDUs / Maximum re-ordering delay exceeds t-Reordering.

UM RLC / In sequence delivery of upper layer PDUs with residual loss of RLC PDUs / Maximum re-ordering delay exceeds t-Reordering.

UM RLC / RLC re-establishment procedure

AM RLC / Segmentation and reassembly / No PDU segmentation

AM RLC / Segmentation and reassembly / Different numbers of length indicators

AM RLC / Reassembly / AMD PDU reassembly from AMD PDU segments / Segmentation Offset and Last Segmentation Flag fields

AM RLC / RLC re-establishment at RRC connection reconfiguration including mobilityControlInfo IE

7.3.1 Maintenance of PDCP sequence numbers for radio bearers7.3.1.1

7.3.1.2

7.3.1.3

7.3.2 RoHC Testing7.3.2.1 RoHC / Correct functionality for profile 0x00007.3.2.2 RoHC / Correct functionality for profile 0x00017.3.2.3 RoHC / Correct functionality for profile 0x00027.3.2.4 RoHC / Correct functionality for profile 0x00047.3.2.5 RoHC: Correct functionality for compressed packets7.3.2.6 RoHC / Correct functionality for standalone packets7.3.3 PDCP ciphering and desiphering7.3.3.1

7.3.3.2

7.3.3.3

7.3.3.4

7.3.4 PDCP integrity protection7.3.4.1

7.3.4.2

7.3.5 PDCP – handover7.3.5.2

7.3.5.3

7.3.5.4

7.3.5.5

7.3.6 PDCP - Others7.3.6.1 PDCP discard

8 Radio Resource Control RRC8.1 RRC connection management procedures8.1.1 Paging8.1.1.1 RRC / Paging for connection in idle mode8.1.1.2 RRC / Paging for notification of BCCH modification in idle mode

8.1.1.3

8.1.1.4

8.1.1.6 RRC / BCCH modification in connected mode8.1.2 RRC connection establishment 8.1.2.1 RRC connection establishment / Ks=1.25 / Success8.1.2.2 RRC connection establishment / Reject with wait time

Maintenance of PDCP sequence numbers / User plane / RLC AMMaintenance of PDCP sequence numbers / User plane / RLC UM / Short PDCP SN (7 bits)Maintenance of PDCP sequence numbers / User plane / RLC UM / Long PDCP SN (12 bits)

Ciphering and deciphering / Correct functionality of EPS AS encryption algorithms / SNOW3GCiphering and deciphering / Correct functionality of EPS UP encryption algorithms / SNOW3GCiphering and deciphering / Correct functionality of EPS AS encryption algorithms / AESCiphering and deciphering / Correct functionality of EPS UP encryption algorithms / AES

Integrity protection / Correct functionality of EPS AS integrity algorithms / SNOW3GIntegrity protection / Correct functionality of EPS AS integrity algorithms / AES

PDCP handover / Lossless handover / PDCP sequence number maintenancePDCP handover / Non-lossless handover / PDCP sequence number maintenancePDCP handover / Lossless handover / PDCP status report to convey the information on missing or acknowledged PDCP SDUs at handover

PDCP handover / In-order delivery and duplicate elimination in the downlink

RRC / Paging for connection in idle mode / Multiple paging recordsRRC / Paging for connection in idle mode / Shared network environment

8.1.2.3

8.1.2.5

8.1.2.6

8.1.2.7

8.1.2.8 RRC connection establishment / Range of access baring time

8.1.2.9

8.1.2.13

8.1.2.14 RRC connection establishment / High speed flag8.1.3 RRc connection release8.1.3.1 RRC connection release / Success8.1.3.4

8.1.3.5 RRC connection release / Success / With priority information

8.1.3.6 RRC connection release / Redirection from E-UTRAN to UTRAN

8.1.3.7 RRC connection release / Redirection from UTRAN to E-UTRAN

8.1.3.8 RRC connection release / Redirection from E-UTRAN to GERAN

8.1.3.9

8.1.3.10

8.2 RRC connection reconfiguration 8.2.1 Radio bearer establishment8.2.1.1

8.2.1.3

8.2.1.5

8.2.1.6

8.2.1.7

RRC connection establishment / Return to idle state after T300 timeoutRRC connection establishment / 0% access probability for MO calls, no restriction for MO signallingRRC connection establishment / Non-zero percent access probability for MO calls, no restriction for MO signalling

RRC connection establishment / 0% access probability for AC 0 to 9, AC 10 is barred, AC 11 to 15 are not barred, access for UE with access class in the range 11 to 15 is allowed

RRC Connection Establishment / 0% access probability for MO calls, non-zero percent access probability for MO signalling

RRC connection establishment / 0% access probability for MO calls, 0% access probability for MO signalling

RRC connection release / Redirection to another E-UTRAN frequency

RRC connection release / Redirection from E-UTRAN to CDMA2000-HRPD

RRC connection release / Redirection from E-UTRAN to CDMA2000-1xRTT

RRC connection reconfiguration / Radio bearer establishment for transition from RRC_IDLE to RRC_CONNECTED / Success / Default bearer / Early bearer establishment

RRC connection reconfiguration / Radio bearer establishment / Success / Dedicated bearerRRC connection reconfiguration / Radio bearer establishment for transition from RRC_IDLE to RRC CONNECTED / Success / Latency check

RRC connection reconfiguration / Radio bearer establishment for transition from RRC_IDLE to RRC CONNECTED / Success / Latency check / SecurityModeCommand and RRCConnectionReconfiguration transmitted in the same TTI

RRC connection reconfiguration / Radio bearer establishment / Success / SRB2

8.2.1.8

8.2.2 Radio resource reconfiguration 8.2.2.1

8.2.2.2

8.2.3 Radio bearer release8.2.3.1

8.2.4 Radio bearer release8.2.4.1

8.2.4.2

8.2.4.3

8.2.4.4

8.2.4.5

8.2.4.6

8.2.4.7

8.2.4.8

8.2.4.9

8.2.4.10

8.2.4.12

8.3 Measurement configuration control and reporting 8.3.1 Intra E-UTRAN measurements8.3.1.1

8.3.1.2

8.3.1.3

8.3.1.4

8.3.1.5

8.3.1.6

8.3.1.7

RRC connection reconfiguration / Radio bearer establishment / Success / Dedicated bearer / ROHC configured

RRC connection reconfiguration / Radio resource reconfiguration / SuccessRRC connection reconfiguration / SRB/DRB reconfiguration / Success

RRC connection reconfiguration / Radio bearer release / Success

RRC connection reconfiguration / Handover / Success / Dedicated preambleRRC connection reconfiguration / Handover / Success / Common preambleRRC connection reconfiguration / Handover / Success / Intra-cell / Security reconfigurationRRC connection reconfiguration / Handover / Failure / Intra-cell / Security reconfigurationRRC connection reconfiguration / Handover / All parameters includedRRC connection reconfiguration / Handover / Success / Inter-frequencyRRC connection reconfiguration / Handover / Failure / Re-establishment successfulRRC connection reconfiguration / Handover / Failure / Re-establishment failureRRC connection reconfiguration / Handover / Inter-band blind handover / SuccessRRC connection reconfiguration / Handover / Between FDD and TDDRRC connection reconfiguration / Handover / Setup and release of MIMO

Measurement configuration control and reporting / Intra E-UTRAN measurements / Event A1Measurement configuration control and reporting / Intra E-UTRAN measurements / Event A2Measurement configuration control and reporting / Intra E-UTRAN measurements / Two simultaneous events A3 (intra and inter-frequency measurements)

Measurement configuration control and reporting / Intra E-UTRAN measurements / Periodic reporting (intra and inter-frequency measurements)

Measurement configuration control and reporting / Intra E-UTRAN measurements / Two simultaneous event A3 (intra-frequency measurements)

Measurement configuration control and reporting / Intra E-UTRAN measurements / Two simultaneous events A2 and A3 (inter-frequency measurements)

Measurement configuration control and reporting / Intra E-UTRAN measurements / Blacklisting

8.3.1.8

8.3.1.9

8.3.1.9a

8.3.1.10

8.3.1.11

8.3.1.11a

8.3.2 Inter-RAT measurements8.3.2.1

8.3.2.2

8.3.2.3

8.3.2.4

8.3.2.5

8.3.2.6

8.3.2.7

8.3.2.8

8.3.2.9

8.3.2.10

8.3.3 Measurements for self optimized networks8.3.3.1

8.3.3.2

8.3.3.3

Measurement configuration control and reporting / Intra E-UTRAN measurements / Handover / IE measurement configuration present

Measurement configuration control and reporting / Intra E-UTRAN measurements / Intra-frequency handover / IE measurement configuration not present

Measurement configuration control and reporting / Intra Frequency measurements / Intra-frequency handover / IE measurement configuration not present

Measurement configuration control and reporting / Intra E-UTRAN measurements / Inter-frequency handover / IE measurement configuration not present

Measurement configuration control and reporting / Intra E-UTRAN measurements / Continuation of the measurements after RRC connection re-establishment

Measurement configuration control and reporting / Intra Frequency measurements / Continuation of the measurements after RRC connection re-establishment

Measurement configuration control and reporting / Inter-RAT measurements / Event B2 / Measurement of GERAN cells

Measurement configuration control and reporting / Inter-RAT measurements /Periodic reporting / Measurement of GERAN cells

Measurement configuration control and reporting / Inter-RAT measurements / Event B2 / Measurement of UTRAN cells

Measurement configuration control and reporting / Inter-RAT measurements / Periodic reporting / Measurement of UTRAN cells

Measurement configuration control and reporting / inter RAT measurements / Periodic reporting / Measurements of E-UTRAN, UTRAN and GERAN cells

Measurement configuration control and reporting / Inter-RAT measurements / Simultaneous A2 and two B2 / Measurements of E-UTRAN, UTRAN and GERAN cells

Measurement configuration control and reporting / Inter-RAT measurements / Event B2 / Measurement of HRPD cells

Measurement configuration control and reporting / Inter-RAT measurements / Periodic reporting / Measurement of HRPD cells

Measurement configuration control and reporting / Inter-RAT measurements / Event B2 / Measurement of 1xRTT cells

Measurement configuration control and reporting / Inter-RAT measurements / Periodic reporting / Measurement of 1xRTT cells

Measurement configuration control and reporting / SON / ANR / CGI reporting of E-UTRAN cellMeasurement configuration control and reporting / SON / ANR / CGI reporting of UTRAN cellMeasurement configuration control and reporting / SON / ANR / CGI reporting of GERAN cell

8.3.3.4

8.3.3.5

8.4 Inter-RAT handover8.4.1 Inter-RAT handover E-UTRA to UTRA8.4.1.1 Inter-RAT handover / From E-UTRA to UTRA PS / Speech8.4.1.2 Inter-RAT handover / From E-UTRA to UTRA PS / Data8.4.1.3 Inter-RAT handover / From E-UTRA to UTRA HSPA / Speech

8.4.1.4 Inter-RAT handover / From E-UTRA to UTRA HSPA / Data8.4.1.5

8.4.2 Inter-RAT handover UTRA to E-UTRA8.4.2.1 Inter-RAT handover / From UTRA PS to E-UTRA / Speech8.4.2.2 Inter-RAT handover / From UTRA PS to E-UTRA / Data8.4.2.3 Inter-RAT handover / From UTRA HSPA to E-UTRA / Speech

8.4.2.4 Inter-RAT handover / From UTRA HSPA to E-UTRA / Data8.4.3 Inter-RAT handover E-UTRA to GERAN8.4.3.1 Inter-RAT handover / From E-UTRA to GPRS / PS HO8.4.3.2

8.4.3.3

Additional Spectrum Emission Mask

8.4.5 Inter-RAT handover E-UTRA to HRPD8.4.5.3

8.4.5.4

8.4.6 Inter-RAT handover HRPD to E-UTRA8.4.6.1

8.4.6.2 Inter-RAT handover / From HRPD Rev A/0 PS to E-UTRA / Data

8.4.7 Inter-RAT handover E-UTRA to 1xRTT8.4.7.1

8.4.7.2

8.4.7.3

8.4.7.4

8.5 RRC others8.5.1 Radio link failure

Measurement configuration control and reporting / SON / ANR / CGI reporting of HRPD cellMeasurement configuration control and reporting / SON / ANR / CGI reporting of 1xRTT cell

Inter-RAT handover / from E-UTRA to UTRA HSUPA/HSDPA / Data

Inter-RAT cell change order / From E-UTRA data RRC_CONNECTED to GPRS / Without NACCInter-RAT cell change order / From E-UTRA data to GPRS / With NACC

Pre-registration at HRPD and inter-RAT handover / From E-UTRA to HRPD Active / SpeechPre-registration at HRPD and inter-RAT handover / From E-UTRA to HRPD Active / Data

Inter-RAT handover / From HRPD Rev A PS to E-UTRA / Speech

Inter-RAT handover / SRVCC from E-UTRA to 1xRTT(CS) / SpeechInter-RAT handover / SRVCC from E-UTRA to 1xRTT(CS) / Speech Handover / Failure / Re-establishment successful

Pre-registration at 1xRTT and inter-RAT handover / CS fallback from E-UTRA RRC_IDLE to 1xRTTPre-Registration at 1xRTT and inter-RAT handover / CS fallback caused by addition of CS service / From E-UTRA Data to 1xRTT

8.5.1.1 Radio link failure / RRC connection re-establishment Success

8.5.1.2 Radio link failure / T301 expiry8.5.1.3 Radio link failure / T311 expiry8.5.1.4 Radio link failure / RRC connection re-establishment reject

8.5.1.5 Radio link failure / Radio link recovery while T310 is running

8.5.1.6 Radio link failure / T311 expiry / Dedicated RLF timer8.5.2 Redirection to E-UTRAN8.5.2.1

8.5.4 UE capability transfer8.5.4.1 UE capability transfer / Success9 EPS mobility management 9.1 EMM common management9.1.2 Authentication procedure9.1.2.1 Authentication accepted9.1.2.3

9.1.2.4 Authentication not accepted by the UE / MAC code failure9.1.2.5 Authentication not accepted by the UE / SQN failure9.1.2.6 Abnormal cases / Network failing the authentication check

9.1.3 Security mode control procedure9.1.3.1 NAS security mode command accepted by the UE9.1.3.2 NAS security mode command not accepted by the UE9.1.3.4 Abnormal cases9.1.4 Identification procedure9.1.4.2 Identification procedure / IMEI requested9.1.5 EMM information procedure9.1.5.1 EMM information procedure9.1.5.2 EMM information procedure not supported by the UE9.2 EMM specific procedures9.2.1 Attach procedure9.2.1.1 Attach procedure for EPS services9.2.1.1.1 Attach / Success / Valid GUTI9.2.1.1.1a

9.2.1.1.1b

9.2.1.1.2 Attach Procedure / Success / With IMSI / GUTI reallocation9.2.1.1.3

9.2.1.1.4

9.2.1.1.7

9.2.1.1.7a

9.2.1.1.9 Attach / Rejected / IMSI invalid9.2.1.1.10 Attach / Rejected / Illegal ME

Redirection to E-UTRAN / From UTRAN upon reception of RRC CONNECTION REJECT

Authentication not accepted by the network / GUTI used, Authentication reject and re-authentication

Attach / Success / Last visited TAI, TAI list and equivalent PLMN list handlingAttach Procedure / Success / Last visited TAI, TAI list and equivalent PLMN list handling / Single Frequency operation

Attach Procedure / Success / Request for obtaining the IPv6 address of the home agentAttach Procedure / Success / Request for obtaining the IPv4 address of the home agentAttach Procedure / Success / List of equivalent PLMNs in the ATTACH ACCEPT messageAttach Procedure / Success / List of equivalent PLMNs in the ATTACH ACCEPT message / Single Frequency operation

9.2.1.1.11

9.2.1.1.12 Attach / Rejected / EPS services not allowed9.2.1.1.13 Attach / Rejected / PLMN not allowed9.2.1.1.13a

9.2.1.1.14 Attach / Rejected / Tracking area not allowed9.2.1.1.15 Attach / Rejected / Roaming not allowed in this tracking area

9.2.1.1.15a

9.2.1.1.16 Attach / Rejected / EPS services not allowed in this PLMN9.2.1.1.16a

9.2.1.1.17 Attach / Rejected / No suitable cells in tracking area9.2.1.1.18 Attach / Rejected / Not authorized for this CSG9.2.1.1.19 Attach / Abnormal case / Failure due to non integrity protection

9.2.1.1.20

9.2.1.1.21

9.2.1.1.22 Attach / Abnormal case / Unssuccesful attach after 5 attempts

9.2.1.1.23 Attach / Abnormal case / Repeated rejects for network failures

9.2.1.1.24 Attach / Abnormal case / Change of cell into a new tracking area9.2.1.1.25 Attach / Abnormal case / Mobile originated detach required

9.2.1.1.26 Attach / Abnormal case / Detach procedure collision9.2.1.2 Combined attach procedure for EPS services and non-EPS services9.2.1.2.1 Combined attach / Success / EPS and non-EPS services9.2.1.2.1b Combined attach / Success / SMS only9.2.1.2.1c

9.2.1.2.2

9.2.1.2.3

9.2.1.2.4

9.2.1.2.5 Combined attach / Rejected / IMSI invalid9.2.1.2.6 Combined attach / Rejected / Illegal ME9.2.1.2.7

9.2.1.2.8 Combined attach / Rejected / EPS services not allowed 9.2.1.2.9 Combined attach / Rejected / PLMN not allowed 9.2.1.2.10 Combined attach / Rejected / Tracking area not allowed9.2.1.2.11

9.2.1.2.12

9.2.1.2.13Combined attach / Rejected / No suitable cells in tracking area

Attach / Rejected / EPS services and non-EPS services not allowed

Attach / Rejected / PLMN not allowed / Single Frequency operation

Attach / Rejected / Roaming not allowed in this tracking area / Single Frequency operation

Attach / Rejected / EPS services not allowed in this PLMN / Single Frequency operation

Attach / Abnormal case / Access barred because of access class barring or NAS signalling connection establishment rejected by the networkAttach / Abnormal case / success after several attempts due to no network response

Combined attach procedure / Success / CS Fallback not preferredCombined attach / Success / EPS services only / IMSI unknown in HSSCombined attach / Success / EPS services only / MSC temporarily not reachableCombined attach / Success / EPS services only / CS domain not available

Combined attach / Rejected / EPS services and non-EPS services not allowed

Combined attach / Rejected / Roaming not allowed in this tracking areaCombined attach / Rejected / EPS services not allowed in this PLMN

9.2.1.2.14 Combined attach / Rejected / Not authorized for this CSG9.2.1.2.15

9.2.2 Detach procedure9.2.2.1 UE initiated detach procedure9.2.2.1.1 UE initiated detach / UE switched off9.2.2.1.2 UE initiated detach / USIM removed from the UE9.2.2.1.3 UE initiated detach / EPS capability of the UE is disabled9.2.2.1.4 UE initiated detach / CS fallback capability of the UE is disabled

9.2.2.1.6

9.2.2.1.7 UE initiated detach / Abnormal case / Detach procedure collision

9.2.2.1.8

9.2.2.1.9

9.2.2.1.10 UE initiated detach / Mapped security context9.2.2.2 Network initiated detach procedure9.2.2.2.1 NW initiated detach / Re-attach required9.2.2.2.2 NW initiated detach / IMSI detach9.2.2.2.14 NW initiated detach / Abnormal case / EMM cause not included

9.2.3 Tracking area updating procedure (S1 mode only)9.2.3.1 Normal and periodic tracking area updating9.2.3.1.1 Normal tracking area update / Accepted9.2.3.1.2 Normal tracking area update / Accepted / "Active" flag set9.2.3.1.4

9.2.3.1.5 Periodic tracking area update / Accepted9.2.3.1.6

9.2.3.1.7

9.2.3.1.8

9.2.3.1.9 Normal tracking area update / Correct handling of CSG list

9.2.3.1.9a

9.2.3.1.10 Normal tracking area update / Rejected / IMSI invalid9.2.3.1.11 Normal tracking area update / Rejected / Illegal ME9.2.3.1.12

9.2.3.1.13

9.2.3.1.14 Normal tracking area update / Rejected / UE implicitly detached

9.2.3.1.15 Normal tracking area update / Rejected / PLMN not allowed

9.2.3.1.15a

9.2.3.1.16

Combined attach / Abnormal case / Handling of the EPS attach attempt counter

UE initiated detach / Abnormal case / Local detach after 5 attempts due to no network response

UE initiated detach / Abnormal case / Detach and EMM common procedure collisionUE initiated detach / Abnormal case / Change of cell into a new tracking area

Normal tracking area update / List of equivalent PLMNs in the TRACKING AREA UPDATE ACCEPT message

Normal tracking area update / UE with ISR active moves to E-UTRANUE performs an intersystem change from S101 mode to S1 mode and has no user data pendingUE receives an indication that the RRC connection was released with cause "load balancing TAU required"

Normal tracking area update / NAS signalling connection recovery

Normal tracking area update / Rejected / EPS service not allowedNormal tracking area update / Rejected / UE identity cannot be derived by the network

Normal tracking area update / Rejected / PLMN not allowed / Single Frequency operationNormal tracking area update / Rejected / Tracking area not allowed

9.2.3.1.17

9.2.3.1.18

9.2.3.1.18a

9.2.3.1.19

9.2.3.1.20

9.2.3.1.21

9.2.3.1.22

9.2.3.1.23

9.2.3.1.25

9.2.3.1.26

9.2.3.1.27

9.2.3.1.28

9.2.3.2 Combined tracking area updating9.2.3.2.1 Combined tracking area update / Successful9.2.3.2.1a

9.2.3.2.1b Combined tracking area update / Success / EPS and SMS only

9.2.3.2.1c

9.2.3.2.2

9.2.3.2.3

9.2.3.2.4

9.2.3.2.5 Combined tracking area update / Rejected / IMSI invalid9.2.3.2.6 Combined tracking area update / Rejected / Illegal ME9.2.3.2.7

9.2.3.2.8

9.2.3.2.9

9.2.3.2.10

9.2.3.2.11 Combined tracking area update / Rejected / PLMN not allowed

9.2.3.2.12

9.2.3.2.13

Normal tracking area update / Rejected / Roaming not allowed in this tracking areaNormal tracking area update / Rejected / EPS services not allowed in this PLMNNormal tracking area update / Rejected / EPS services not allowed in this PLMN / Single Frequency operationNormal tracking area update / Rejected / No suitable cells in tracking areaNormal tracking area update / Rejected / Not authorized for this CSGNormal tracking area update / Rejected / No EPS bearer context activated Normal tracking area update / Abnormal case / access barred due to access class control or NAS signalling connection establishment rejected by the network

Normal tracking area update / Abnormal case / Success after several attempts due to no network response / TA belongs to TAI list and status is UPDATED / TA does not belong to TAI list or status is not UPDATED

Normal tracking area update / Abnormal case / Failure after 5 attempts due to no network responseNormal tracking area update / Abnormal case / TRACKING AREA UPDATE REJECTNormal tracking area update / Abnormal case / Change of cell into a new tracking areaNormal tracking area update / Abnormal case / Tracking area updating and detach procedure collision

Combined tracking area update / Successful / Check of last visited TAI and handling of TAI list, LAI and TMSI

Combined tracking area update / Success / CS Fallback not preferredCombined tracking area update / Successful for EPS services only / IMSI unknown in HSSCombined tracking area update / Successful for EPS services only / MSC temporarily not reachableCombined tracking area update / Successful for EPS services only / CS domain not available

Combined tracking area update / Rejected / EPS services and non-EPS services not allowedCombined tracking area update / rejected / EPS services not allowed Combined tracking area update / Rejected / UE identity cannot be derived by the networkCombined tracking area update / Rejected / UE implicitly detached

Combined tracking area update / Rejected / Tracking area not allowedCombined tracking area update / Rejected / Roaming not allowed in this tracking area

9.2.3.2.14

9.2.3.2.15

9.2.3.2.16

9.2.3.2.17

9.2.3.3 Iu mode to S1 mode inter-system change in idle mode9.2.3.3.1

First Iu mode to S1 mode inter-system change after attach9.2.3.3.2

9.2.3.3.3

9.2.3.3.4

9.2.3.3.5 Periodic routing area update9.2.3.3.5a Periodic location update9.2.3.3.6

9.2.3.4 A/Gb mode to S1 mode inter-system change9.2.3.4.1

9.3 EMM connection management procedures (S1 mode only)9.3.1 Service request procedure9.3.1.1 Service Request initiated by UE for user data9.3.1.3 Service Request / Mobile originating CS fallback9.3.1.4 Service Request / Rejected / IMSI invalid9.3.1.5 Service Request / Rejected / Illegal ME9.3.1.6 Service Request / Rejected / EPS services not allowed9.3.1.7

9.3.1.7a Service Request / Rejected / UE implicitly detached9.3.1.12a

9.3.1.14 Service Request / Abnormal case / T3417 expired9.3.1.15

9.3.1.169.3.1.17 Service Request / Abnormal case / Procedure collision9.3.1.18 Service request / Rejected / Not authorized for this CSG9.3.2 Paging procedure9.3.2.1 Paging procedure9.3.2.2 Paging for CS fallback / Idle mode9.3.2.2a Paging for CS fallback / Connected mode9.4 NAS security9.4.1

9.4.2

Combined tracking area update / Rejected / EPS services not allowed in this PLMNCombined tracking area update / Rejected / No suitable cells in tracking areaCombined tracking area update / Rejected / Not authorized for this CSGCombined tracking area update / Abnormal case / handling of the EPS tracking area updating attempt counter

Iu mode to S1 mode intersystem change / ISR is active / Expiry of T3312 in E-UTRAN or T3412 in UTRAN and further intersystem change

Iu mode to S1 mode intersystem change / Periodic TAU and RAU / ISR activated, T34xx expiredAttach in E-UTRAN / RAU to UTRAN / Go to UTRAN RRC idle / TAU in E-UTRAN

E-UTRAN RRC connection failure / Reselection of UTRAN cell / NAS signaling to release old S1 interface connection

TAU/RAU procedure for inter-system cell reselection between A/Gb and S1 modes

Service Request / Rejected / UE identity cannot be derived by the network

Extended Service Request / Rejected / CS domain temporarily not available

Service Request / Abnormal case / Tracking area update procedure is triggeredService Request / Abnormal case / Switch off

Integrity protection / Correct functionality of EPS NAS integrity algorithm / SNOW3GIntegrity protection / Correct functionality of EPS NAS integrity algorithm / AES

9.4.3

9.4.4

10 EPS session management10.1 Default EPS bearer context activation10.2 Dedicated EPS bearer context activation10.2.1 Dedicated EPS bearer context activation / Success10.3 EPS bearer context modification10.3.1 EPS bearer context modification / Success10.4 EPS bearer context deactivation10.4.1 EPS bearer context deactivation / Success10.5 UE requested PDN connectivity10.5.1

10.5.3 UE requested PDN connectivity procedure not accepted10.6 UE requested PDN disconnect10.6.1

10.6.2

10.7 UE requested bearer resource allocation10.7.1

10.7.2

10.7.3

10.7.4 UE requested bearer resource allocation / Expiry of timer T3480

10.7.5

10.8 UE requested bearer resource modification10.8.1

10.8.2

10.8.3

10.8.4

10.8.5

10.8.6

10.8.7

10.9 UE routing of uplinks packets10.9.1 UE routing of uplinks packets11 General Tests11.1 SMS over SGs11.1.1 MT-SMS over SGs / Idle mode

Ciphering and deciphering / Correct functionality of EPS NAS encryption algorithm / SNOW3GCiphering and deciphering / Correct functionality of EPS NAS encryption algorithm / AES

UE requested PDN connectivity procedure accepted by the network

UE requested PDN disconnect procedure accepted by the networkUE requested PDN disconnect procedure not accepted by the network

UE requested bearer resource allocation, accepted by the network / New EPS bearer contextUE requested bearer resource allocation accepted by the network / Existing EPS bearer context

UE requested bearer resource allocation not accepted by the network

UE requested bearer resource allocation / BEARER RESOURCE ALLOCATION REJECT message including cause #43, "invalid EPS bearer identity"

UE requested bearer resource modification accepted by the network / New EPS bearer contextUE requested bearer resource allocation accepted by the network / Existing EPS bearer context UE requested bearer resource allocation not accepted by the networkUE requested bearer resource modification / Cause #36 "regular deactivation"UE requested bearer resource modification / BEARER RESOURCE MODIFICATION REJECT message including cause #43 "unknown EPS bearer context"

UE requested bearer resource modification / Collision of a UE requested bearer resource modification procedure and EPS bearer context deactivation procedure

UE requested bearer resource modification / Expiry of timer T3481

11.1.2 MT-SMS over SGs / Active mode11.1.3 MO-SMS over SGs / Idle mode11.1.4 MO-SMS over SGs / Active mode12 E-UTRA Radio Bearer Tests12.2 MIMO not configured12.2.1 Data transfer of E-UTRA radio bearer combinations 1, 3, 6 and 9

12.2.2

12.2.3

12.2.4 Data transfer of E-UTRA radio bearer combination 1312.3 MIMO configured12.3.1

12.3.2

12.3.3

12.3.4 Data transfer of E-UTRA radio bearer combination 13 / MIMO

13 Multi-layer Procedures13.1 Call setup13.1.1

13.1.2

13.1.2a

13.1.313.1.4

13.1.5

13.1.6

13.1.7

13.1.8

13.1.9

13.1.10

13.1.11

13.1.12

13.1.13

13.1.14 CS fallback / Abnormal cases / Timer T3317ext expiry13.1.15

13.2 RRC connection reconfiguration

Data transfer of E-UTRA radio bearer combinations 2, 4, 7 and 10Data transfer of E-UTRA radio bearer combinations 5, 6, 8, 11 and 12

Data transfer of E-UTRA radio bearer combinations 1, 3, 6 and 9 / MIMOData transfer of E-UTRA radio bearer combinations 2, 4, 7 and 10 / MIMOData transfer of E-UTRA radio bearer combinations 5, 6, 8, 11 and 12 / MIMO

Activation and deactivation of additional data radio bearer in E-UTRACall setup from E-UTRAN RRC_IDLE / CS fallback to UTRAN with redirection / MO callCall setup from E-UTRAN RRC_IDLE / CS fallback to UTRAN with redirection including System Information / MO call

Call setup from E-UTRAN RRC_CONNECTED / CS fallback to UTRAN with redirection / MT callCall setup from E-UTRAN RRC_IDLE / CS fallback to UTRAN with handover / MT callCall setup from E-UTRAN RRC_CONNECTED / CS fallback to UTRAN with handover / MO callEmergency call setup from E-UTRAN RRC_IDLE / CS fallback to UTRAN with handoverCall setup from E-UTRA RRC_IDLE / CS fallback to GSM with redirection / MT callCall setup from E-UTRA RRC_CONNECTED / CS fallback to GSM with redirection / MO callCall setup from E-UTRA RRC_IDLE / CS fallback to GSM with CCO without NACC / MO callCall setup from E-UTRA RRC_CONNECTED / CS fallback to GSM with CCO without NACC / MT callCall setup from E-UTRA RRC_IDLE / CS fallback to GSM with PSHO / EDTM not supported / MT callCall setup from E-UTRA RRC_CONNECTED / CS fallback to GSM with PSHO / EDTM not supported / MO call

Call setup from E-UTRA RRC_IDLE / CS fallback to GSM with PSHO / EDTM supported / MT call

Call setup from E-UTRAN RRC_IDLE / CS fallback to UTRAN with redirection / MT call / UTRAN cell is barred

13.2.1 RRC connection reconfiguration / E-UTRA to E-UTRA13.3 Connection re-establishment13.3.1 Intra-system connection re-establishment13.3.1.1

13.3.1.2

13.3.2 Inter-system connection re-establishment13.3.2.1

13.3.2.2

13.3.2.3

13.4 Mobility13.4.1 Intra-system mobility13.4.1.2 Inter-frequency mobility / E-UTRA to E-UTRA packet13.4.1.3

13.4.1.5

13.4.2 Inter-system mobility packet13.4.2.1 Inter-system mobility / E-UTRA to UTRA packet13.4.2.2 Inter-system mobility / E-UTRA to GPRS packet13.4.2.3 Inter-system mobility / E-UTRA to CDMA2000 packet13.4.2.4

13.4.2.5

13.4.3 Inter-system mobility voice13.4.3.1

13.4.3.2

13.4.3.3 Inter-system mobility / E-UTRA voice to GSM CS voice / SRVCC

13.4.3.4

13.4.3.5

14 ETWS14.1 ETWS reception in RRC_IDLE state / Duplicate detection14.2

14.3

Intra-system connection re-establishment / Radio link recovery while T310 is runningIntra-system connection re-establishment / Re-establishment of a new connection when further data is to be transferred

Inter-system connection re-establishment / E-UTRAN to UTRAN / Further data are to be transferredInter-system connection re-establishment / E-UTRAN to GPRS / Further data are to be transferredInter-system connection re-establishment / E-UTRAN to CDMA2000 / Further data are to be transferred

Intra-system mobility / E-UTRA FDD to E-UTRA TDD to E-UTRA FDD packetRRC connection reconfiguration / Handover/ Full configuration / DRB establishment

Inter-system mobility / Service based redirection from UTRA to E-UTRAInter-system mobility / Service based redirection from GSM/GPRS to E-UTRA

Inter-system mobility / E-UTRA voice to UTRA CS voice / SRVCCInter-system mobility / E-UTRA PS voice + PS data to UTRA CS voice + PS data / SRVCC

Inter-system mobility / E-UTRA voice to UTRA CS voice / Unsuccessful case / Retry on old cell / SRVCCInter-system mobility / E-UTRA voice to GSM CS voice / Unsuccessful case / Retry on old cell / SRVCC

ETWS reception in RRC_CONNECTED state / Duplicate detectionETWS reception in RRC_IDLE state / NITZ timestamp security check

LTE 3GPP Band 13 Signaling GCF Conformance Test Plan

Selection

LTE GCF Testing is required with latest test case list (www.globalcertificationforum.org)

Lab Conformance

LTE SFNTest Cases

Regression Test Cases

Execute Test Cases from Latest GCF Test Case List

X

X

X

X

X

X X

X X

X

X X

X

X

X X

X

X

X X

X

X

X

X X

X

X

X X

X X

X

X XX

X XX

X X

X

X

X

X

X

X X

X

X

X

X

X

X

X

X

X

X

X

X

X X

LTE 3GPP Band 13 Signaling GCF Conformance Test Plan

Comments

LTE GCF Testing is required with latest test case list (www.globalcertificationforum.org)

LTE 3GPP Band 13 Supplementary Signaling Conformance Test Plan

Test Case Selection

Lab Conformance

2.1 EUTRAN Initial Attach (for IMS PDN with Piggybacking) X2.2 RRC UE Feature Group Support X2.3 IPv6 Address Assignment X2.4 E-UTRAN Initial Attach (APN Disabled) X2.5 E-UTRAN Initial Attach (for IMS PDN without piggybacking) X2.7 UE Initiated PDN Connection (EMM-Idle) X2.8 UE Initiated PDN Connection (EMM-Connected) X2.9 UE Initiated PDN Connection (APN disabled) X2.12 P-GW Initiated PDN Disconnect (EMM-Connected) X2.13 UE Initiated Detach for E-UTRAN (EMM-Connected) – 3 PDNs Scenario X

2.14 UE Initiated Detach for E-UTRAN (EMM-Idle) – 3 PDNs Scenario X2.15 MME Initiated Detach (EMM-Connected) – 3 PDNs Scenario X2.16 UE re-initiated connection to IMS PDN after disconnected X2.17 UE response to PDN disconnect reject X2.18 UE initiated PDN disconnection – Update to APN parameters X2.19 UE support of multiple DNS addresses X2.20 X

2.21 X

2.22 X

2.30 Network Initiated EPS Dedicated Bearer Activation (EMM-Connected) X2.31 Network Initiated PDN Disconnect (No Data Usage Available) X2.32 UE Initiated Internet PDN Connection with QoS (EMM-Connected)2.34 Time Retrieval via SIB16 Message X2.35 UE Indicates RACH Report Capability X2.36 UE Reports RACH Information Upon Request by Network X2.37 UE Initiated Tracking Area Update after Radio Link Failure X2.38 UE Response to PDN Disconnect Reject Code 43 X2.39 UE Routes DNS Queries

2.40.1 Attach / Abnormal case / Network reject with Extended Wait Timer2.40.2

2.40.3 Normal tracking area update / low priority override2.40.4

2.40.5UE requested PDN connectivity accepted / Dual priority / T3396 override

UE Initiated PD Disconnection - Update To APN Parameters (EMM-Connected)Network Initiated EPS Bearer Modification Without QoS Update (EMM-Connected)Network Initiated EPS Bearer Modification With QoS Update (EMM-Connected)

Attach Procedure / EAB broadcast handling / ExtendedAccessBarring configured in the UE

Normal tracking area update / EAB broadcast handling / ExtendedAccessBarring configured in the UE / ExtendedAccessBarring and Override_ExtendedAccessBarring configured in the UE

2.40.6UE requested PDN connectivity accepted / Dual priority / T3346 override

2.40.7

2.40.8

2.41 feICIC GCF Signaling and Protocol Test Cases 2.42 feICIC FEATURE GROUP and UE Capability SUPPORT 2.43

2.44 2.44 DL CoMP UE CAPABILITY SUPPORT2.45

2.46 2.46 UE DOWNLINK SUPERVISION 2.47

2.48 2.48 INTER-FREQUENCY MEASUREMENT REPORT ORDER 2.49 2.49 MDT GCF Signaling and Protocol Test cases 2.50 2.50 R10 Logged MDT UE capability Report

UE requested PDN connectivity not accepted / Network reject with Extended Wait TimerUE requested bearer resource modification / Dual priority / low priority override

2.43 RRCConnectionReConfiguration when CRS-AssistanceInfoList-r11 is present

2.45 DL CoMP HANDOVER WITH TRANSMISSION MODE CHANGE

2.47 NON-ESSENTIAL SYSTEM INFORMATION DETECTION FAILURE

LTE 3GPP Band 13 Supplementary Signaling Conformance Test Plan

Selection Comments

LTE SFN

X XX X X

X X

X X XX

XX

X X

X

X

X

X

XX

XXX

Regression Test Cases

Required TCs for device using Certified Chipset

LTE Data Retry Test Plan

Test Case Selection

Lab Conformance

2 RRC errors2.1 RRC Connection Reject - Initial Attach X2.2 RRC Connection Reject - Sending Data to PDN X2.4 Network Does Not Respond To RACH X2.5 Multiple RRC Failures X3 EMM common procedures3.1 UE fails to authenticate to the NW - Invalid MAC X3.2 UE fails to authenticate to the NW - Invalid Value for Seperation Bit X3.3 UE fails to authenticate to the NW - Invalid Value for SQN field X3.5 UE sends "Security Mode Reject" - Initial Attach X4 EMM specific procedures4.4 UE receives "Attach Reject" msg from the NW X4.6 UE receives "Detach Request" from NW X4.7 UE receives "Detach Request" from NW X4.8 UE receives "Detach Request" from NW X4.9 UE Receives Attach Reject Message From The Network X4.10 X

4.12 X

4.13 UE Receives Attach Reject Message from the Network Codes X4.14 X

4.15 4.15 PERMANENT ATTACH FAILURES ACROSS POWER CYCLE4.16

5 EMM connection management procedures5.2 UE receives "Service Reject" from NW X5.3 UE receives "Service Reject" from NW X5.5 Service Reqest Fails: Service Attempt Counter Reaches Max Value X

5.6 UE Receives Service Reject message From The Network X5.9 UE Receives Tracking Area Update Reject Message From The Network X

5.11 X

5.12 UE Receives Tracking Area Update Reject Message From The Network X

5.13 X

Note: Execute All Error Codes For Each TC as per Test Plan (except note listed for TC6.7)

UE withT3346 Timer Suport received Attach Reject Message from the NetworkUE Receives Attach Reject and PDN Conectivity Reject Message from the Network

UE WITH T3245 TIMER RECEIVES ATTACH REJECT MESSAGE FROM THE NETWORK

4.16 PERMANENT EMM FAILURES ACROSS POWER CYCLE WITH DETACH REQUEST

Tracking Area Update Request Fails: Tracking Area Update Attempt Counter Reaches Max Value

UE with T3346 Timer Support Receives Service Reject Message from the Network

5.14 X

5.15 X

5.16 X

5.17

5.18

6 EPS session management6.1 NW fails to assign an IPv6 address X6.2 NW fails to refresh the IPv6 address for the IMS PDN X6.3 X

6.4 X

6.5 X

6.7

X

6.9 X

6.10 X

6.11 Network Fails to Respond to PDN Connectivity Request X6.12 X

6.13 X

6.14 X

6.15X

6.16X

6.17 X

6.18 UE Makes Excessive PDN Connectivity Requests X6.19 UE Makes Attach request While Throttling On PDN X6.21

X

7 Network Initiated ESM Procedures7.1 X

7.2 X

7..3X

UE without T3346 Timer Support Receives Service Reject Message from the NetworkUE with T3346 Timer Support Receives Tracking Area Update Reject Message from the NetworkUE without T3346 Timer Support Receives Tracking Area Update Reject Message from the Network5.17 PERMANENT EMM FAILURES ACROSS POWER CYCLE WITH SERVICE REQUEST 5.18 PERMANENT EMM FAILURES ACROSS POWER CYCLE WITH TRACKING AREA UPDATE

Network Fails to Assign an IPv6 Address for a non-IMS PDN- Initial Connection, no IPv4 address assignedNetwork Fails to Assign an IPv6 Address for a non-IMS PDN- Initial Connection, IPv4 address assignedUE Receives PDN Connectivity Reject message from the Network for the IMS PDN- Initial AttachmentUE receives "PDN Connectivity Reject" msg from NW For Non-IMS PDN

(This Note is applicable to LTE SFN Only: Execute this test case for all error codes except - 95,96,97,98,99,100 as per test plan)

UE Receives PDN Connectivity Reject Message From The Network for Non-IMS PDNUE Receives PDN Connectivity Reject message from the Network for IMS PDN

Network Fails to Refresh the IPv6 Address for the IMS PDN, IPv4 Address AssignedNetwork Fails to Assign an IPv6 Address for the IMS and Internet PDNs on Network Attach, IPv4 Address Assigned to Internet PDNNetwork Fails to Assign an IPv6 Address for the Internet PDN on Network Attach, No IPv4 Address AssignedNetwork Fails to Include IMS P-CSCF Address in Activate Default EPS Bearer Context Request message for the IMS PDN, Initial Attach

Network Fails to Include IMS P-CSCF Address in Activate Default EPS Bearer Context Request message during an IMS PDN Connection Attempt

UE receives PDN Connectivity Reject Message from the Network for Admin PDN

UE RECEIVES PDN CONNECTIVITY REJECT MESSAGE FROM THE NETWORK FOR NON-IMS PDN: CODES 26 AND 27 WITH T3396 TIMER SET

UE Receives Deactivate EPS Bearer Context Request message from the Network: 2 PDN Connections Open

UE Receives Deactivate EPS Bearer Context Request message from the Network: 1 PDN Connection Open

UE Receives Deactivate EPS Bearer Context Request message from the Network

LTE Data Retry Test Plan

Selection

LTE SFN

X XX

X

XXXX X

X XX X

XX X X

X

X

X

X XX X

X

X

X

X

Regression Test Cases

Required TCs for device using Certified

Chipset

X

X

X

X XX X

X X

X

X

X X X

X

X

X

X

X

X

X

X

X

X

X

X X

X

X

LTE Data Retry Test Plan

Selection

X

XX

X

X

Required Test Cases for Device using Certified

Module

X

X

LTE Over the Air Radiated Performance Test Plan Test Case Selection

Lab Conformance

2 Transmitter Tests

2.1 X X

3 Receiver Tests3.1 TOTAL ISOTROPIC SENSITIVITY (TIS)3.1.3.1 Conducted Sensitivity X X3.1.3.2 Primary Receiver TIS X X3.1.3.3 Secondary/MIMO Reciver TIS X X

3.2 X X

Notes: * using classical TIS approach defined in CTIA ERP Working Group contribution CPWG101007-1 under the section titled "6.X.1 Test Procedure – Complex Pattern Data Not Required".

Regression Test Cases

TOTAL RADIATED POWER (TRP) – NO MPR OR A-MPR

RECEIVER ENVELOPE CORRELATION COEFFICIENT

LTE Over the Air Radiated Performance Test Plan Comments

( * see notes below )( * see notes below )

* using classical TIS approach defined in CTIA ERP Working Group contribution CPWG101007-1 under the section titled "6.X.1 Test Procedure – Complex Pattern Data Not Required".

LTE Device-UICC (USIM, ISIM) Interaction Test Plan

Test Case

2. VZW_LTE_UICC (ETSI TS Rel 8 102 230)1 5.1.5.62 5.2.2.13 5.2.2.24 5.2.35 5.2.46 5.2.57 6.28 6.39 6.510 7.1.111 7.1.212 7.2.113 7.2.214 7.2.315 7.2.416 7.2.517 7.2.618 7.2.71920

3. VZW_LTE_USIM (3GPP TS 31.121)1 5.1.6

2 5.1.7

3 5.1.8

4 5.1.9

5 5.1.10

6 5.2.27 6.1.18 6.1.29 6.1.310 6.1.411 6.1.5

Current Test Case Number

ETSI or 3GPP Test Case Section

12 6.1.6

13 6.1.10

14 6.1.1115 6.1.1216 6.1.1317 6.1.1418 6.1.1526 7.1.427 7.1.528 7.1.629 7.2.537 8.2.138 8.2.239 8.540 9.1.441 9.1.5

43 11.1

44 11.2

45 11.3

4. USAT Interaction (3GPP TS 31.124)1 27.22.1/1

2 27.22.2

3 27.22.3

4 27.22.4.4.1/1

5 27.22.4.6

6 27.22.4.7.17 27.22.4.7.1

8 27.22.4.7.1/3

9 27.22.4.7.1

10 27.22.4.7.1

11 27.22.4.7.1

13 27.22.4.7.2

16 27.22.4.10.7

17 27.22.4.10.7

18 27.22.4.10.7

20 27.22.4.10.7

21 27.22.4.10.7

22 27.22.4.14.1/2

23 27.22.4.15.1/17

24 27.22.4.15.1/2

25 27.22.4.15.1/4

26 27.22.4.15.1/5

27 27.22.4.15.1/14

28 27.22.4.15.1

28a 27.22.4.15.1/15

33 27.22.4.21.1/1

34 27.22.4.21.1

35 27.22.4.21.1/3

36 27.22.4.21.1/4

37 27.22.4.21.1/5

38 27.22.4.21.1/6

39 27.22.4.21.2/1

40 27.22.4.21.2/2

41 27.22.4.27.6/1

42 27.22.4.27.6/2

43 27.22.4.27.6/3

44 27.22.4.27.6

44a 27.22.4.27.6/4

44b

44c

44d 27.22.4.27.6/5

45 27.22.4.28.3/1

45a 27.22.4.28.3/2

46 27.22.4.28.1

47 27.22.4.28.1

48 27.22.4.29.1/2

49 27.22.4.30.3/150 27.22.4.30.3/251 27.22.4.30.152 27.22.4.30.153 27.22.4.30.154 27.22.4.31 1/1

55 27.22.4.31 1/4

56 27.22.4.31 1/5

57 27.22.5.3/158 27.22.5.3/159 27.22.5.3/160 27.22.5.3/165 27.22.7.4.1/266 27.22.7.10.167 27.22.7.11

68 27.22.7.17. 1/1

69 27.22.7.17. 1/2

70 27.22.4.7.35. Device - ISIM Interaction

5.15.25.35.4

6.Test Cases: Multiple PLMN6.16.26.56.7

LTE Device-UICC (USIM, ISIM) Interaction Test Plan

Test Case

Title

2. VZW_LTE_UICC (ETSI TS Rel 8 102 230)Reaction of a Terminal receiving no ATRElectrical tests on contact C1, Test 1

Electrical tests on contact C1, Test 2

Electrical tests on contact C2Electrical tests on contact C3Electrical tests on contact C7Clock stop mode with 1,8V technology UICCClock stop mode with 3V technology UICCSpeed EnhancementBit/character duration during the transmission from the Terminal to the UICCBit/character duration during the transmission from the UICC to the TerminalTimingCommand processing, ACK, NACK, NULL procedure bytesCase 2 command, use of procedure bytes '61xx' and '6Cxx'Case 4 command, use of procedure bytes '61xx'Command processing, warning and error status bytesError correctionError detectionCommand processing, multiple NULL procedure bytesCase 4 command, use of procedure bytes '6100'

3. VZW_LTE_USIM (3GPP TS 31.121)

Device identification by short IMSI when accessing LTE/EPC

Device identification by short IMSI using a 2 digit MNC when accessing LTE/EPC

Device Identification after changed IMSI with service " EMM Information" not available

Access Control Information handling for LTE/EPCEntry of PINChange of PINUnblock PINEntry of PIN2Change of PIN2

Device Identification by GUTI when using USIM with service "EMM Information “not available

Device Identification by GUTI when using USIM with service "EMM Information" available

Unblock PIN2

Entry of PIN on multi-verification capable UICC'sChange of PIN on multi-verification capable UICCsUnblock PIN on multi-verification capable UICCsEntry of PIN2 on multi-verification capable UICC'sChange of PIN2 on multi-verification capable UICCsUnblock PIN2 on multi-verification capable UICCsAdding FPLMN to the Forbidden PLMN list when accessing LTE Device updating forbidden PLMNs when accessing LTEDevice deleting forbidden PLMNs when accessing LTEDevice updating the User controlled PLMN selector list for E-UTRANCorrect storage of a Short Message on the USIMCorrect reading of a Short Message on the USIMUICC presence detection when connected to E-UTRAN/EPCAccess Point Name Control List handling for Devices supporting ACLNetwork provided APN handling for Devices supporting ACL

NAS security context parameter handling when service "EMM Information" is available

4. USAT Interaction (3GPP TS 31.124)PROFILE DOWNLOAD

Contents of the TERMINAL PROFILE commandServicing of proactive UICC commands

More time

Poll IntervalREFRESH, USIM InitializationREFRESH, File Change Notification

REFRESH, USIM Initialization and File Change Notification

REFRESH, USIM Initialization and Full File Change Notification

REFRESH, USIM Initialization after SMS-PP data download

REFRESH, USIM Application Reset

REFRESH, USIM Application Reset for IMSI Changing procedure

NAS security context parameter handling when service "EMM Information" is not available no IMSI change

NAS security context parameter handling when service "EMM Information" is not available, IMSI changed

SEND SHORT MESSAGE, SMS-over-IP, E-UTRAN (IMS), packing not required, SMS default alphabet, successful

SEND SHORT MESSAGE, SMS-over-IP, E-UTRAN (IMS), packing required, alpha identifier, 8 bit data, message of 160 characters user data, successful

SEND SHORT MESSAGE, SMS-over-IP, E-UTRAN (IMS), packing not required, alpha identifier, SMS default alphabet, message of 160 characters user data, successful

POLLING OFF, E-UTRAN

PROVIDE LOCAL INFORMATION, IMEI of the device

PROVIDE LOCAL INFORMATION, Date, Time, Time Zone

PROVIDE LOCAL INFORMATION, Language, setting

PROVIDE LOCAL INFORMATION, Access Technology, E-UTRAN

PROVIDE LOCAL INFORMATION, IMEISV of the terminal

PROVIDE LOCAL INFORMATION, E-UTRAN Intra-Frequency Measurements

TIMER MANAGEMENT, start 8 timers successfully

TIMER EXPIRATION, pending proactive UICC command)

TIMER EXPIRATION, UICC application toolkit busy

CLOSE CHANNEL, Default EPS bearer, successful

CLOSE CHANNEL, EPS bearer with APN different from default APN, successful

CLOSE CHANNEL, with an invalid channel identifier

SEND SHORT MESSAGE, SMS-over-IP, E-UTRAN (IMS), alpha identifier length '00', packing not required, 8-bit data, successfulSEND SHORT MESSAGE, SMS-over-IP, E-UTRAN (IMS), packing not required, 8-bit data, no alpha identifier, successful

PROVIDE LOCAL INFORMATION, Local Information, E-UTRAN Local Info (MCC, MNC, TAC & E-UTRAN Cell ID)

TIMER MANAGEMENT, start timer 1 several times, get the current value of the timer and deactivate the timer successfullyTIMER MANAGEMENT, start timer 2 several times, get the current value of the timer and deactivate the timer successful

TIMER MANAGEMENT, start timer 8 several times, get the current value of the timer and deactivate the timer successfully

TIMER MANAGEMENT, try to get the current value of a timer which is not started: action in contradiction with the current timer state

TIMER MANAGEMENT, try to deactivate a timer which is not started: action in contradiction with the current timer state

OPEN CHANNEL, immediate link establishment, E-UTRAN, bearer type '02' (Refer to additional details in section 4.1 below)

OPEN CHANNEL, immediate link establishment, E-UTRAN, bearer type '0B'(Refer to additional details in section 4.1 below)

OPEN CHANNEL, Immediate link establishment, E-UTRAN, bearer type '02', with Network Access Name, with alpha identifierOPEN CHANNEL, immediate link establishment, E-UTRAN, bearer type '0B', with alpha identifierOPEN CHANNEL, immediate link establishment, E-UTRAN, bearer type '0B', with alpha identifier user did not accept the proactive commandOPEN CHANNEL related to packet data service bearer (bearer description - default bearer with UDP connection)OPEN CHANNEL related to packet data service bearer (bearer description - default bearer with TCP connection)OPEN CHANNEL, immediate link establishment, E-UTRAN, bearer type ‘03’ – Default EPS bearer

CLOSE CHANNEL, on an already closed channel

RECEIVE DATA, already opened channel, E-UTRAN, APN different from default)SEND DATA, E-UTRAN, Default EPS bearer, immediate modeSEND DATA, E-UTRAN, APN different from default APN, Store modeSEND DATA, Store mode, Tx buffer fully usedSEND DATA, 2 consecutive SEND DATA Store modeSEND DATA, immediate mode with a bad channel identifierGET CHANNEL STATUS, without any BIP channel opened

GET CHANNEL STATUS, EPS bearer with APN different from default APN

SMS-PP Data Download, General Data Coding, AcknowledgementSMS-PP Data Download, General Data Coding FETCH, MORE TIMESMS-PP Data Download, with Data Coding / Message ClassSMS-PP Data Download, General Data Coding, User Data Header payloadEVENT DOWNLOAD -LOCATION STATUS, E-UTRANEVENT DOWNLOAD - Data available

EVENT DOWNLOAD - Channel Status on a link dropped

EVENT DOWNLOAD – Network Rejection, ATTACH REJECT

EVENT DOWNLOAD – Network Rejection, TRACKING AREA UPDATE REJECT

REFRESH, Steering of roaming, E-UTRAN5. Device - ISIM Interaction

Handling Private User IdentityHandling of Public User Identity in IMS RegistrationHandling of Public User Identity for mobile originating IMS sessionsHome Domain Usage

6.Test Cases: Multiple PLMNPLMN operations, UE supports EHPLMN list sent by UICCPLMN operations, UE supports OPLMNwACT list sent by UICCPLMN operations, UE decodes up to 6 PLMN IDsPLMN operations, UE prioritizes HOME PLMN over ROAMING PLMN

GET CHANNEL STATUS, EPS bearer with APN different from default APN, after a link is dropped

LTE Device-UICC (USIM, ISIM) Interaction Test Plan

Selection

LTE SFN

XXXXXXXXXXXXXXXXXXXX

3. VZW_LTE_USIM (3GPP TS 31.121)X

X

X

X

X

XXX

LTE GCF Testing is required with latest test case list (www.globalcertificationforum.org)

Lab ConformanceRegression Test Cases

X

XX

XX

X

X

X

X

X

4. USAT Interaction (3GPP TS 31.124)X

X

X X

X

XX

X

X X

X

X

X

X

X

X

X

X

X

X X

X X

X X

X

X X

X X

X

X

X X

X

X

X X

X X

X X

X

X X

X X

X

X

X X X

X X

X X

X X

X X

X

X

X X

X XXX XX XXX X

X X

X X

X XX XX XX XXX XX

X

X

5. Device - ISIM InteractionXXXX

6.Test Cases: Multiple PLMN

LTE Device-UICC (USIM, ISIM) Interaction Test Plan

Selection

XXXXXXXXXXXXXXXXXXXX

Required Test Cases for Device using Certified Module

LTE SMS Test Plan

Test Case Selection

Lab Conformance

2.10 2.10 DEVICE MO SMS FORMAT SETTING- DEFAULT VZ_TC_LTESMS_6301 X2.11 2.11 DEVICE MO SMS FORMAT SETTING- MODIFIED VZ_TC_LTESMS_6302 X2.12 2.12 MOBILE ORIGINATED SMS MESSAGE- 3GPP2 SMS VZ_TC_LTESMS_6303 X X X2.13 2.13 MOBILE ORIGINATED SMS MESSAGE- 3GPP SMS VZ_TC_LTESMS_6304 X X X2.14 2.14 Mobile Terminated SMS message- 3GPP2 SMS VZ_TC_LTESMS_6305 X X2.15 2.15 MOBILE TERMINATED SMS MESSAGE- 3GPP SMS VZ_TC_LTESMS_6306 X X2.16 2.16 MO 3GPP2 SMS VERIFY SIP MESSAGE HEADERS VZ_TC_LTESMS_6307 X X2.17 2.17 MO 3GPP SMS VERIFY SIP MESSAGE HEADERS VZ_TC_LTESMS_6308 X X2.18 2.18 MO 3GPP2 SMS MESSAGE- VERIFY SIP CALL FLOW VZ_TC_LTESMS_6309

2.18.4 Test procedure- SIP 200 OK Response X X2.18.5 Test procedure- SIP 202 ACCEPTED Response X X2.19 2.19 MO 3GPP SMS MESSAGE- VERIFY SIP CALL FLOW VZ_TC_LTESMS_6312

2.19.4 Test procedure- SIP 200 OK Response X X2.19.5 Test procedure- SIP 202 ACCEPTED Response X X2.20 2.20 MT 3GPP2 SMS MESSAGE- VERIFY SIP CALL FLOW VZ_TC_LTESMS_6315 X X2.21 2.21 MT 3GPP SMS MESSAGE- VERIFY SIP CALL FLOW VZ_TC_LTESMS_6316 X X X

2.22 X X

2.23 X

2.24 2.24 APPLICATION DIRECTED SMS- OTADM VZ_TC_LTESMS_6319 X

2.26 X

2.28 X

2.29 X X

2.30 X X

2.31 X X

2.32 X X

2.33 2.33 MO 3GPP2 SMS - SIP errors VZ_TC_LTESMS_63262.33.4 Test Procedure- SIP 400 BAD REQUEST X X X2.33.5 Test Procedure- SIP 404 NOT FOUND X X2.33.6 Test Procedure -SIP 500 SERVER INTERNAL ERROR X X2.33.7 Test Procedure- SIP 502 BAD GATEWAY X X2.33.8 Test Procedure- SIP 503 SERVICE UNAVAILABLE ERROR X X2.34 2.34 MO 3GPP SMS SIP ERRORS VZ_TC_LTESMS_6332

2.34.4 Test Procedure- SIP 400 BAD REQUEST X X2.34.5 Test Procedure- SIP 404 NOT FOUND X X2.34.6 Test Procedure -SIP 500 SERVER INTERNAL ERROR X X2.34.7 Test Procedure- SIP 502 BAD GATEWAY X X2.34.8 Test Procedure- SIP 503 SERVICE UNAVAILABLE ERROR X X2.35 2.35 MO 3GPP2 SMS RETRY BEHAVIOR VZ_TC_LTESMS_6338

2.35.4 Test Procedure - No Response from IMS X X2.35.5 Test Procedure - SIP error from IMS X X

2.36

2.36.4 Test Procedure - No Response from IMS X2.36.5 Test Procedure - SIP error from IMS X

2.38

2.38.4 Test Procedure - No Response from IMS X2.38.5 Test Procedure - SIP error from IMS X

2.39 X X

2.40

2.40.4 Test Procedure - SMS_Over_IP_Networks_Indication and IMS Test mode are "disabled" X X

2.40.5 Test Procedure - SMS_over_IP_Networks_Indication and IMS Test mode are "enabled" X X

2.40.6 X X

2.42 X

2.51

Regression Test Cases

Required TCs for device using Certified

Chipset

2.22 MO 3GPP2 SMS MESSAGE SIZE MORE THAN 1 SEGMENT OF TEXT VZ_TC_LTESMS_63172.23 MO 3GPP SMS MESSAGE SIZE MORE THAN 1 SEGMENT OF TEXT VZ_TC_LTESMS_6318

2.26 SMS MESSAGES STORAGE SETTING (DEFAULT) - 3GPP SMS VZ_TC_LTESMS_63202.28 SMS MESSAGES STORAGE SETTING (MODIFIED) - 3GPP SMS VZ_TC_LTESMS_63212.29 MO 3GPP2 SMS RETRY BEHAVIOR-DEFAULT SIP T1, TIMER F AND T2 TIMERS VZ_TC_LTESMS_63222.30 MO 3GPP SMS RETRY BEHAVIOR-DEFAULT SIP T1, TIMER F AND T2 TIMERS VZ_TC_LTESMS_63232.31 MO 3GPP2 SMS RETRY BEHAVIOR-MODIFIED SIP T1, TIMER F AND T2 TIMERS VZ_TC_LTESMS_63242.32 MO 3GPP SMS RETRY BEHAVIOR-MODIFIED SIP T1, TIMER F AND T2 TIMERS VZ_TC_LTESMS_6325

2.36 MO 3GPP SMS RETRY BEHAVIOR-DEFAULT SMS STORAGE SETTING VZ_TC_LTESMS_6341

2.38 MO 3GPP SMS RETRY BEHAVIOR-MODIFIED SMS STORAGE SETTING VZ_TC_LTESMS_6344

2.39 DEVICE IMS REGISTRATION CONTROL PARAMETERS- DEFAULT VZ_TC_LTESMS_6347

2.40 DEVICE IMS REGISTRATION CONTROL PARAMETER- MODIFIED VZ_TC_LTESMS_6348

Test Procedure - SMS_over_IP_Networks_Indication and IMS Test mode are "disable" and "enable" respectively

2.42 DEVICE IMSI BASED IMS REGISTRATION-SMS OPERATION VZ_TC_LTESMS_6353

2.51 DEVICE IMS INTERACTION- IPSEC CONFIDENTIALITY PROTECTION VZ_TC_LTESMS_6355

2.54 X

2.55 X

2.56 VOID2.57 VOID

2.58 X

2.59 2.59 MO 3GPP SMS - MESSAGE STATUS REPORT VZ_TC_LTESMS_6360 X X2.60 2.60 MO 3GPP2 SMS ENCODED USING 7 BIT ASCII VZ_TC_LTESMS_6361 X2.61 2.61 MT 3GPP2 SMS ENCODED USING 7 BIT ASCII VZ_TC_LTESMS_6362 X2.62 2.62 MO 3GPP SMS ENCODED USING GSM 7- BIT VZ_TC_LTESMS_6363 X2.63 2.63 MT 3GPP SMS ENCODED USING GSM 7- BIT VZ_TC_LTESMS_6364 X2.64 2.64 MO 3GPP2 SMS ENCODED USING GSM 7- BIT VZ_TC_LTESMS_6365 X2.65 2.65 MT 3GPP2 SMS ENCODED USING GSM 7- BIT VZ_TC_LTESMS_6366 X

2.66 2.66 MO 3GPP2 SMS Encoded Using UCS-2(ISOIEC 10646-1) VZ_TC_LTESMS_6367 X

2.67 2.67 MT 3GPP2 SMS Encoded Using UCS-2(ISOIEC 10646-1) VZ_TC_LTESMS_6368 X

2.68 2.68 MO 3GPP SMS Encoded Using UCS-2(ISOIEC 10646-1) VZ_TC_LTESMS_6369 X

2.69 2.69 MT 3GPP SMS Encoded Using UCS-2(ISOIEC 10646-1) VZ_TC_LTESMS_6370 X

2.70 2.70 MT 3GPP2 SMS Encoded Using IA5 (ITU-T T.50) VZ_TC_LTESMS_6371 X2.71 2.71 MT 3GPP2 SMS Encoded Latin (ISO 8859-1) VZ_TC_LTESMS_6372 X2.72 2.72 MT SMS Messages storage Function - 3GPP SMS VZ_TC_LTESMS_6373 X

2.73

2.74

2.75

2.54 MT 3GPP2 CONCATENATED SHORT MESSAGE (MORE THAN 1 SEGMENT OF TEXT) VZ_TC_LTESMS_63572.55 MT 3GPP CONCATENATED SHORT MESSAGE (MORE THAN 1 SEGMENT OF TEXT) VZ_TC_LTESMS_6358

2.58 MO 3GPP2 SMS MESSAGE DELIVERY ACKNOWLEDGEMENTS VZ_TC_LTESMS_6359

2.73 MT SIM OTA Wake Up SMS After IMS Registration Using the IMSI-based SIP URI VZ_TC_LTESMS_6374

2.74 DEVICE MO SMS - VERIFY FORMAT SETTING (DEFAULT is 3GPP2), SIP MESSAGE Headers, and SIP Call Flow

2.75 DEVICE MO SMS - VERIFY FORMAT SETTING- MODIFIED, SIP MESSAGE Headers, and SIP Call Flow VZ_TC_LTESMS_9562..........................................................................................................

LTE AT Commands For Test Automation Test Plan Test Case

2 Tests From Specification 3GPP TS 27.0072.1 REQUEST MANUFACTURER IDENTIFICATION (+CGMI)2.2 REQUEST MODEL IDENTIFICATION (+CGMM)2.3 REQUEST REVISION IDENTIFICATION (+CGMR)2.4 REQUEST PRODUCT SERIAL NUMBER IDENTIFICATION (+CGSN)2.5 SELECT TE CHARACTER SET (+CSCS)2.6 REQUEST INTERNATIONAL MOBILE SUBSCRIBER IDENTITY (+CIMI)2.7 EXTENDED ERROR REPORT (+CEER)2.8 PHONE ACTIVITY STATUS (+CPAS)2.9 SET PHONE FUNCTIONALITY (+CFUN)2.10 ENTER PIN (+CPIN)2.11 LIST ALL AVAILABLE AT COMMANDS (+CLAC)2.12 DEFINE PDP CONTEXT (+CGDCONT)2.13 PS ATTACH OR DETACH (+CGATT)2.14 PDP CONTEXT ACTIVATE OR DEACTIVATE (+CGACT)2.15 SHOW PDP ADDRESS (+CGPADDR)2.16 EPS NETWORK REGISTRATION STATUS (+CEREG)2.17 MESSAGE FORMAT (+CMGF)2.18 LIST MESSAGES (+CMGL)2.19 READ MESSAGE (+CMGR)2.20 DELETE MESSAGE (+CMGD)2.22 PCCA STD 101 [17] SELECT WIRELESS NETWORK (+WS46)2.23 SUBSCRIBER NUMBER (+CNUM)2.24 PLMN SELECTION (+COPS)2.25 FACILITY LOCK (+CLCK)2.26 CHANGE PASSWORD (+CPWD)2.27 READ OPERATOR NAMES (+COPN)2.28 SIGNAL QUALITY (+CSQ)2.29 INDICATOR CONTROL (+CIND)2.30 CLOCK (+CCLK)2.31 GENERIC SIM ACCESS (+CSIM)2.32 RESTRICTED SIM ACCESS (+CRSM)2.33 PRINTING IP ADDRESS FORMAT (+CGPIAF)2.34 EXTENDED SIGNAL QUALITY (+CESQ)2.35 REPORT MOBILE TERMINATION ERROR (+CMEE)2.36 DEFINE SECONDARY PDP CONTEXT (+CGDSCONT)2.37 TRAFFIC FLOW TEMPLATE (+CGTFT)2.38 PDP CONTEXT MODIFY (+CGCMOD)2.39 PACKET DOMAIN EVENT REPORTING (+CGEREP)2.40 SELECT SERVICE FOR MO SMS MESSAGES (+CGSMS)### PDP CONTEXT READ DYNAMIC PARAMETERS (+CGCONTRDP)2.42 SECONDARY PDP CONTEXT READ DYNAMIC PARAMETERS (+CGSCONTRDP)### TRAFFIC FLOW TEMPLATE READ DYNAMIC PARAMETERS (+CGTFTRDP)2.44 EPS QUALITY OF SERVICE READ DYNAMIC PARAMETERS (+CGEQOSRDP)

### SELECT MESSAGE SERVICE (+CSMS)### PREFERRED MESSAGE STORAGE (+CPMS)### SERVICE CENTRE ADDRESS (+CSCA)### SET TEXT MODE PARAMETERS (+CSMP)2.50 SEND MESSAGE (+CMGS)### SEND MESSAGE FROM STORAGE (+CMSS)### WRITE MESSAGE TO MEMORY (+CMGW)3 Tests From Specification 3GPP TS 27.0053.1 MOBILE TERMINATION EVENT REPORTING (+CMER)3.2 COMMAND TOUCH SCREEN ACTION (+CTSA)3.6 KEYPAD CONTROL (+CKPD)4 Tests For VZW Specific Commands4.1 EDIT APN TABLE (+VZWAPNE)4.2 READ RSRP VALUES (+VZWRSRP) - For Future Study4.3 READ RSRQ VALUES (+VZWRSRQ) - For Future Study

LTE AT Commands For Test Automation Test Plan Selection Comments

Lab Conformance

XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

XXXXXXX

XXX

LTE Data Throughput Test Plan

Test Cases

2 LATENCY TESTS2.1 NETWORK ATTACHMENT TIME2.1 Network Attachment Time2.2 RRC_IDLE TO RRC_CONNECTED CONTROL PLANE LATENCY

Test 1Test 2

2.3 USER PLANE ROUND TRIP DELAYTest 1Test 2

2.4INTERNET PDN MTU SIZE ENFORCEMENT - IPV4 -TEST 1INTERNET PDN MTU SIZE ENFORCEMENT - IPV4 -TEST 2INTERNET PDN MTU SIZE ENFORCEMENT - IPV6 -TEST 1INTERNET PDN MTU SIZE ENFORCEMENT - IPV6 -TEST 2

3 THROUGHPUT TESTS3.1 DOWNLINK FTP THROUGHPUT

Test 1Test 2Test 3Test 4Test 7Test 8Test 9Test 10Test 11Test 12

3.2 UPLINK FTP THROUGHPUTTest 1Test 2Test 3Test 4Test 5

3.3 BIDIRECTIONAL FTP THROUGHPUTTest 1Test 2Test 3

3.4 DOWNLINK UDP THROUGHPUTTest 1Test 2

Note: Please see latest test plan for details.

This test confirms the UE meets Verizon Wireless requirements for MTU size on the internet PDN.

Test 3Test 4Test 5Test 6Test 7Test 8Test 9Test 10Test 11Test 12

3.5 UPLINK UDP THROUGHPUTTest 1Test 2Test 3Test 4Test 5

3.6 BIDIRECTIONAL UDP THROUGHPUTTest 1Test 2Test 3

3.7 MULTI-FLOW THROUGHPUT WITH QOS3.7.1 UDP Data Transfer with Simultaneous SMS Delivery

Test 1Test 2

3.7.2 Simultaneous IPv4 and IPv6 UDP Data TransfersTest 1Test 2

3.7.3 Simultaneous IPv4 and IPv6 UDP Data Transfers and SMS DeliveryTest 1Test 2

3.8 STRESS TEST – FTP THROUGHPUT (DOWNLINK)Test 1Test 2

3.9 STRESS TEST – UDP THROUGHPUTTest 1Test 2

3.10 DOWNLINK POWER SWEEP – UDP THROUGHPUTDownlink Power Sweep – UDP Throughput

3.11 DOWNLINK UDP THROUGHPUT WITH VARIABLE REFERENCE MEASUREMENT CHANNELS – FUTURE3.11 Downlink UDP Throughput Wiith Variable Reference Measurement Channels3.12 DOWNLINK UDP THROUGHPUT WITH ADVANCED CHANNEL MODELS3.12.1 Downlink UDP Throughput with Antenna Gain Imbalance

3.12.2 Downlink UDP Throughput with Dynamic Correlation and Antenna Gain Imbalance

3.12.3Downlink UDP Throughput with Spatial Channel Models

3.12.4 CQI and RI Reporting with Frequency Selective Interference3.13 3.13 feICIC DOWNLINK FTP THROUGHPUT IN VICTIM CELL

Test 1Test 2Test 3Test 4

Test 5Test 6Test 7Test 8Test 9Test 10Test 11Test 12

3.14 3.14 feICIC DOWNLINK UDP THROUGHPUT IN VICTIM CELL Test 1Test 2Test 3Test 4Test 5Test 6Test 7Test 8Test 9Test 10Test 11Test 12

3.15 3.15 feICIC FTP THROUGHPUT in AGGRESSOR CELLTest 1Test 2

3.16 3.16 Single Cell Data Thruput Test while CRS-AssistanceInfoList-r11 is Present

3.17

3.18

3.193.20 3.20 DL COMP DATA THROUGHPUT TESTS WITH TWO TRANSMISSION POINTS

Test 1Test 2Test 3Test 4Test 5Test 6Test 7Test 8Test 9Test 10Test 11Test 12Test 13

3.21 3.21 DL COMP DATA THROUGHPUT TESTS WITH THREE TRANSMISSION POINTS

Test 1Test 2Test 3Test 4Test 5Test 6

3.17 CRS IC (non-Colliding CRS) DOWNLINK FTP THROUGHPUT, Neighbour NOT Loaded 3.18 CRS IC (non-Colliding CRS) DOWNLINK FTP THROUGHPUT, Neighbour Fully Loaded with OCNG

3.19 CRS IC (Colliding CRS) DOWNLINK FTP THROUGHPUT, Neighbour NOT Loaded

Test 7Test 8

3.22 3.22 DL COMP DATA THROUGHPUT TESTS WITH PDSCH IN MBSFN SUBFRAMES

Test 1Test 2

LTE Data Throughput Test Plan

Selection

Lab Conformance

X

XX

X XX X

XXXXXXXXXX

XXXXX

XXX

X X XX X X

Regression Test Cases

Required TCs for Device using

Certified Chipset

Required Test Cases for Device using Certified

Module

X X XX X X

X X XX X XX X XX X XX X XX X X

X X XX X XX X XX X XX X X

X X XX X XX X X

X X XX

X X XX X

X X3.11 DOWNLINK UDP THROUGHPUT WITH VARIABLE REFERENCE MEASUREMENT CHANNELS – FUTURE

X X

X X

X X

Informational Only

X

LTE IMS Registration and IMS Registration Retry

Test Case

2.0

2.1

2.2

2.3

2.4

2.6

2.7

2.8

2.92.11

Test 1Test 2Test 3Test 5

2.12 2.12 UE INITIATED DE-REGISTRATION ‘ AIRPLANE MODE VZ_TC_IMSREGRTY_7254

2.132.14 2.14 NETWORK INITIATED DE-REGISTRATION VZ_TC_IMSREGRTY_7256

2.15

2.162.17 2.17 IMS REGISTRATION RETRY ‘NETWORK REJECTS REQUEST 2.18 2.18 IMS REGISTRATION RETRY ‘NETWORK REJECTS REQUEST2.19 2.19 IMS REGISTRATION RETRY ‘NETWORK REJECTS REQUEST

2.20

2.212.22 2.22 IMS REREGISTRATION RETRY ‘NETWORK REJECTS REQUEST2.23 2.23 IMS REREGISTRATION RETRY ‘NETWORK REJECTS REQUEST

Note: Execute All Error Codes For Each TC as per Test Plan

2.1 DEVICE INITIAL REGISTRATION USING THE MSISDN-BASED SIP URI AND DIGEST-AKAV2 AUTHENTICATION VZ_TC_IMSREGRTY_72432.2 DEVICE INITIAL REGISTRATION USING THE MSISDN-BASED SIP URI AND IMS-AKA USING IPSEC AUTHENTICATION - OPTIONAL VZ_TC_IMSREGRTY_72442.3 DEVICE INITIAL REGISTRATION USING THE IMSI-BASED SIP URI ‘ MSISDN NOT PROVISIONED ON THE USIM VZ_TC_IMSREGRTY_72452.4 DEVICE INITIAL REGISTRATION USING THE IMSI-BASED SIP URI ‘ MSISDN-BASED SIP URI INVALID VZ_TC_IMSREGRTY_7246 2.6 DEVICE INITIAL REGISTRATION ‘ SMS_OVER_IP_NETWORKS_INDICATION IS SET TO DISABLE VZ_TC_IMSREGRTY_72482.7 DEVICE INITIAL REGISTRATION ‘ IMS TEST MODE IS SET TO ENABLE VZ_TC_IMSREGRTY_7249 2.8 UE INITIATED DEVICE REREGISTRATION WITHOUT NETWORK CHALLENGE VZ_TC_IMSREGRTY_7250 2.9 UE INITIATED DEVICE REREGISTRATION WITH NETWORK CHALLENGE VZ_TC_IMSREGRTY_72512.11 DEVICE INITIATED DE-REGISTRATION ‘ UE INITIATED LTE DETACH ON POWER DOWN VZ_TC_IMSREGRTY_7253

2.13 UE INITIATED DE-REGISTRATION ‘ UE INITIATED IMS PDN DISCONNECT VZ_TC_IMSREGRTY_7255

2.15 IMS REGISTRATION RETRY ‘ GENERAL CASE, NETWORK IGNORES REQUEST VZ_TC_IMSREGRTY_7257 2.16 IMS REGISTRATION RETRY ‘ GENERAL CASE, NETWORK REJECTS REQUEST VZ_TC_IMSREGRTY_7258

2.20 IMS REREGISTRATION RETRY ‘ GENERAL CASE, NETWORK IGNORES REQUEST VZ_TC_IMSREGRTY_7262 2.21 IMS REREGISTRATION RETRY ‘ GENERAL CASE, NETWORK REJECTS REQUEST VZ_TC_IMSREGRTY_7263

2.24 2.24 IMS REREGISTRATION RETRY ‘NETWORK REJECTS REQUEST

2.25

2.26

2.272.27.2 Test 12.27.3 Test 22.27.4 Test 3

2.282.28.2 Test 12.28.3 Test 2

2.29

2.302.31 2.31 UE INITIATED RE-SUBSCRIBE VZ_TC_IMSREGRTY_7273 2.32 2.32 RE-SUBSCRIBE REJECTED

2.332.34 2.34 DE-REGISTRATION REJECTED

2.35 2.35 CONNECTION FAILURE PRIOR TO IMS REGISTRATION VZ_TC_IMSREGRTY_7277

2.36

2.37 2.37 SUBSCRIBE TIMEOUT AFTER LOWER LAYER FAILURE VZ_TC_IMSREGRTY_7279

2.25 IMS REGISTRATION RETRY THROTTLING TIMERS ACROSS SYSTEM TRANSITIONS VZ_TC_IMSREGRTY_72672.26 RESET OF IMS REGISTRATION RETRY THROTTLING TIMERS ON POWER CYCLE VZ_TC_IMSREGRTY_72682.27 IMS REGISTRATION BEHAVIOR ACROSS SYSTEM TRANSITIONS VZ_TC_IMSREGRTY_7269

2.28 IMS REGISTRATION BEHAVIOR AFTER ENCOUNTERING NO SERVICE CONDITION VZ_TC_IMSREGRTY_7270

2.29 REGISTRATION BEHAVIOR AFTER A NETWORK INITIATED DETACH VZ_TC_IMSREGRTY_7271 2.30 REGISTRATION BEHAVIOR AFTER A NETWORK INITIATED DISCONNECT OF THE IMS PDN VZ_TC_IMSREGRTY_7272

2.33 IMS REREGISTRATION RETRY ‘ REGISTRATION TIMER EXPIRES WHILE THROTTLING VZ_TC_IMSREGRTY_7275

2.36 LOWER LAYER FAILURE DURING IMS REGISTRATION RETRY VZ_TC_IMSREGRTY_7278.87

LTE IMS Registration and IMS Registration Retry

Selection

Lab Conformance LTE SFN

X X

X X

X

X

X X

X

X

X X

X XX XX XX X

X

X XX

X X

X XX XX XX X

X

X X

XX

X

X

X X

XXX

XX

X

X

X XX

X

X

X

X

X

LTE BAND 13 DEVICE INTEROPERABILITY TEST PLAN

Test Case

33.23.3

3.43.53.63.73.83.93.103.113.123.133.143.153.163.173.183.193.203.213.223.23

44.1

4.1.14.1.5

4.24.2.14.2.2

4.34.3.1

4.4.14.4.14.4.2

4.54.5.1

4.5.2

4.64.6.1

4.74.7.14.7.24.7.34.7.44.8

4.8.1

55.15.25.35.4

5.4.4

5.4.5

5.4.6

5.4.7

5.4.8

5.4.9

5.4.10

5.4.11

5.4.12

6.0

6-3.1-X6-3.8-X6-3.9-X

6-3.10-X6-3.11-X6-3.12-X6-3.13-X6-3.14-X

6-4.1.1-X6-4.1.2-X6-4.4.1-X6-4.4.2-X

7

72

7374

LTE BAND 13 DEVICE INTEROPERABILITY TEST PLAN

Test Case

TS.11 Test Cases (GSMA Testcase Section)Attach Reject, cause #7 "EPS Services not allowed"Attach Reject, cause #14 "EPS Services not allowed in this PLMN" - Single PLMN environment

Attach Reject, cause #11 "PLMN not allowed"Attach Reject, cause #3 "Illegal UE"Detach - with power-offDetach - without power-offNormal Tracking Area Update without ISR activation; SuccessfulPeriodic Tracking Area Update; SuccessfulNetwork Selection - Manual Mode - Network on Forbidden ListNetwork Selection - Manual Mode - Empty Prefered PLMN ListNetwork Selection - Manual Mode - More than 32 entries on Preferred PLMN ListNetwork Selection - Selection mode following switch off - Manual Network SelectionNetwork Selection - Selection mode following switch off - Automatic Network SelectionIdle Mode E-UTRA Intra-Frequency ReselectionE-UTRA Handover, intra eNodeB Handover - default bearerE-UTRA Handover, X2 Based - default bearerE-UTRA Handover, S1 Based - default bearerE-UTRA Handover, inter-MME - default bearerPDN Connectivity Request - ESM Information transfer flag=TRUEPDN Connectivity Reject, cause #27 Missing or unknown APNMultiple PDN Connections - Secondary PDN Connectivity RequestMultiple PDN Connections - Secondary PDN Connectivity Disconnect

Verizon Wireless Attach, Detach and Transition Test CasesAttach TestcasesBasic Attach with NAS Security AlgorithmsAttach Reject – Cause Code #15 (No Suitable Cells in Tracking Area)

Disconnect Test CasesPDN Gateway Disconnect Procedure - Network InitiatedPDN Gateway Disconnect Procedure - UE Initiated

Tracking Area Update Test CasesTracking Area Update Reject, cause code #3 (Illegal UE)

System Lost Test CasesLTE System Lost in RRC_IDLELTE System Lost in RRC_ACTIVE

Transition Test CasesIdle to Active Transition – Service Request

Idle to Active Transition – Paging

Automatic Neighbor Relations FunctionIntra-LTE/Frequency Automatic Neighbor Relation (ANR) FunctionSR over PRACH FunctionCBRA, Re-Synchronization of ULPDCCH Ordred Re-synchronizationCBRA, Schedule RequestTime Alignment Timer ExpiryPDN MTUPDN MTU Size

Verizon Wireless Performance Test CasesIPv4 Performance – No MobilityIPV4 Performance – With MobilityIPv6 Performance – No MobilityIPV6 Performance – With MobilityTransmit Diversity Throughput Measure – Downlink QPSK - FTP and UDP Downlink FTP Measured Rate Downlink UDP Measured RateTransmit Diversity Throughput Measure - Uplink QPSK - FTP and UDP Uplink FTP Measured Rate Uplink UDP Measured RateTransmit Diversity Throughput Measure - Downlink QPSK & Uplink QPSK - FTP and UDP Downlink FTP Measured Rate Uplink FTP Measured Rate Downlink UDP Measured Rate Uplink UDP Measured RateOpen Loop Spatial Multiplexing Throughput Measure - Downlink QPSK - FTP and UDP Downlink FTP Measured Rate Downlink UDP Measured RateOpen Loop Spatial Multiplexing Throughput Measure - Uplink QPSK - FTP and UDP Uplink FTP Measured Rate Uplink UDP Measured Rate

Downlink FTP Measured Rate Uplink FTP Measured Rate Downlink UDP Measured Rate Uplink UDP Measured RateClosed Loop Spatial Multiplexing Throughput Measure - Downlink QPSK - FTP and UDP Downlink FTP Measured Rate Downlink UDP Measured RateClosed Loop Spatial Multiplexing Throughput Measure - Uplink QPSK - FTP and UDP Uplink FTP Measured Rate Uplink UDP Measured Rate

Downlink FTP Measured Rate Uplink FTP Measured Rate Downlink UDP Measured Rate Uplink UDP Measured Rate

Open Loop Spatial Multiplexing Throughput Measure - Downlink QPSK + Uplink QPSK - FTP and UDP

Closed Loop Spatial Multiplexing Throughput Measure - Downlink QPSK & Uplink QPSK - FTP and UDP

Supplementary Test Cases for UICC Compatibility TestingRepeat as needed. Also update the summary tab as needed.Attach and Default EPS bearer context activationNormal Tracking Area Update without ISR activation; SuccessfulPeriodic Tracking Area Update; SuccessfulNetwork Selection - Manual Mode - Network on Forbidden ListNetwork Selection - Manual Mode - Empty Prefered PLMN ListNetwork Selection - Manual Mode - More than 32 entries on Preferred PLMN ListNetwork Selection - Selection mode following switch off - Manual Network SelectionNetwork Selection - Selection mode following switch off - Automatic Network Selection

Basic Attach with NAS Security AlgorithmsVOIDLTE System Lost in RRC_IDLELTE System Lost in RRC_ACTIVEPRIMARY AND SECONDARY SYNCHRONIZATION SIGNAL RECEPTION

Loss of One eNodeb Antenna Path While Device is in Idle Mode Loss of one eNodeB antenna path While Device is in Connected Mode

SUCCESSFUL HANDOVER FROM CELL WITH SRS ENABLED TO A CELL WITH SRS DISABLED WITH ONGOING UDP TRAFFIC

LTE BAND 13 DEVICE INTEROPERABILITY TEST PLAN

TS.11 Test Cases (GSMA Testcase Section)

XX

X

XXXX

XX

X

X

XX

Required Test Cases for OEM using certified chipset without changes in modem software

X

XX

Verizon Wireless Performance Test CasesVOIDVOIDVOID

IPV6 Performance – With Mobility

X

X

X

Supplementary Test Cases for UICC Compatibility Testing

XX

X

XX

PRIMARY AND SECONDARY SYNCHRONIZATION SIGNAL RECEPTION