xi technical guide · 2018. 10. 18. · rvdf reveal double flange 5 drywall metal stud item id...

TECHNICAL GUIDEWWW.XTREMEIAS.COM

844.365.9462

Extruded Aluminum Trim: Innovative Solutions for Interior Applications

© 2017 XTREMEINTERIOR™ ARCHITECTURAL SOLUTIONS

SPEC

IFIC

AT

ION

SBest Practice/Before Installation:

Read construction drawings to ensure correct layout and placement. Contractor to make sure that blocking has been provided prior to installation for proper installation where necessary.

An outside corner is the best place to begin installation of XtremeInterior™. Choose one that makes the most sense for your project. XtremeInterior reveals offers many options.

Cutting and Painting:

XtremeInterior recommends that full ten-foot length profiles be used when and wherever possible.

XtremeInterior aluminum trim can be cut with a chop saw, using non-ferrous carbide miter saw blade when cutting metal. An abrasive cut-off wheel should never be used to cut aluminum trims.

XtremeInterior recommends that lubricant (WD-40 or grease stick) be applied to the blade before each cut. Lubricant should be cleaned off of trim prior to painting and installation.

Clear Anodized Aluminum Moldings:

XtremeInterior does not recommend painting clear anodized trim. We provide (as a standard), primed and ready to receive paint profiles, that are kept in stock.

If field painting of clear anodized moldings is necessary, the following steps must be taken to improve the bond between the paint and the aluminum surface:

Clean and treat moldings with an acid etch solution (i.e. mild concentration of muriatic acid), then rinse thoroughly and allow to dry. An “acid-etched” primer is also available depending on the paint manufacturer's recommendations.

Use a primer recommended by the paint manufacturer.

Apply the paint coat according to the paint manufacturer's specifications.

XtremeInterior makes no guarantees, nor accepts any responsibility, for the performance of field-applied coatings over anodized finishes.

Installation Instructions for Interior Trim with tape and float Flanges:

Moldings with tape and float flanges are to be installed while the drywall/gypsum board is being installed. The installer must provide space for the moldings at the time of drywall/gypsum board installation or cut the drywall/gypsum board with a router.

The framing / blocking should provide a backer so that moldings can be attached with (recommended) #6 drywall screws 16” on center.

Before the taping process begins, installation flanges should be cleaned. If veneer plaster is specified, the installation flanges must be treated with a bonding agent. Reveals should be masked to prevent compound joint, drywall mud or texture overspray in order to prevent the entering the reveal opening.

Painted aluminum moldings should be masked with vinyl tape. Use cloth or vinyl tape specifically manufactured for masking anodized aluminum trims.

Drywall tape should not overlap the edge of the reveal. An 8” wide trowel should be used to apply the final skim coat.

Fiberglass or self-adhesive drywall tape will shorten taping time and assist in the prevention of possible cracking.

Installation Instructions for Interior Trim without tape and float Flanges:

Trim without tape and float flanges are to be installed prior to the drywall/gypsum board being installed.

The framing should provide a backer so that moldings can be attached with #6 drywall screws 16” on center.

Reveals should be masked in order to prevent compound joint, drywall mud or texture overspray from entering the reveal opening.

Limited Waranty:

Tamlyn warrants defective free products for a period of 10 years for the original purchaser unless otherwise stated for the specific product ordered. Tamlyn products are further warranted as to adequacy of design, provided products are properly specified and installed. This warranty

does not apply in the event products are altered in any way or are improperly installed. Liability is limited to replacement of products proven to be defective. Tamlyn has made no other warranty, expressed or implied, regarding its products, including but not limited to, any warranty regarding merchantability or fitness for a specific purpose. Any claim that a product is defective must be brought within one (1) month of the date of installation of such products to the original purchaser. Customer hereby agrees that no other incidental or consequential damages are the responsibility of Tamlyn.

The following voids any warranty regarding Tamlyn products:

Product has been improperly installed

Building codes have not been followed.

Products not installed by a contractor /installer with common knowledge of the building industry.

Responsibility remains with the architect or engineer, contractor, and owner for the design, application and proper installation of each Tamlyn product. Specifier and user shall determine the suitability of products for specific application and assume all responsibilities in connection there within.

Aluminum does not rust, however it does corrode. XtremeInterior has a protective coating to cover the bare aluminum. When making cuts on XtremeInterior, recoating will be required at ends, surface scratches, or when performing form cuts. Failure to do this voids your warranty. For answers to your technical questions on recoating consult your local paint manufacturer before installation.

Please follow gypsum board manufacturers best practice application when installing any Tamlyn accessory. XtremeInterior profiles are for aesthetic purposes only (the channel and insert pieces are to be installed vertically and up to ____ degrees at an angle. They are not intended to be used as hand rails or any form of storage shelf) the architect and builder are responsible for designing and installing a code compliant building. XtremeInterior products are not a part of a structural design and are not intended to be used as structural members.

RV Reveal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

RVDF Reveal Double Flange . . . . . . . . . . . . . . . . 5

RVRD Reveal Round . . . . . . . . . . . . . . . . . . . . . . . 6

RVRS Reveal Square . . . . . . . . . . . . . . . . . . . . . . 7

RVSA Reveal Square Angled . . . . . . . . . . . . . . . . . 8

RVST Reveal Square Tapered . . . . . . . . . . . . . . . . 9

RVV Reveal V . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

RVVF Reveal V Flange . . . . . . . . . . . . . . . . . . . . . 11

BPR Base Projecting Round . . . . . . . . . . . . . . . . 12

BPRR Base Projecting Round Reveal . . . . . . . . . . . 13

BPS Base Projecting Square . . . . . . . . . . . . . . . . 14

BPSR Base Base Projecting Square Reveal . . . . . . 15

BRDF Base Reveal Double Flange . . . . . . . . . . . . . 16

BRF Base Reveal Flange . . . . . . . . . . . . . . . . . . . 17

BRL Base Reveal Ledge . . . . . . . . . . . . . . . . . . . 18

BSL Base Shadow Line . . . . . . . . . . . . . . . . . . . . 19

CAC Corner Arc . . . . . . . . . . . . . . . . . . . . . . . . . 20

CBD Corner Bead . . . . . . . . . . . . . . . . . . . . . . . . 21

CBV Corner Bevel . . . . . . . . . . . . . . . . . . . . . . . 22

CEL Corner Elliptical . . . . . . . . . . . . . . . . . . . . . 23

CRA Corner Radiused . . . . . . . . . . . . . . . . . . . . 24

CRD Corner Round . . . . . . . . . . . . . . . . . . . . . . 25

CRR Corner Rectangular Radiused . . . . . . . . . . . 26

CRS Corner Rectangular Square . . . . . . . . . . . . . 27

CRT Corner Rectangular Tapered . . . . . . . . . . . . 28

CSQ Corner Square . . . . . . . . . . . . . . . . . . . . . . 29

CXF Corner X . . . . . . . . . . . . . . . . . . . . . . . . . . 30

ICAC Inside Corner Arc . . . . . . . . . . . . . . . . . . . . 31

ICBV Inside Corner Bevel . . . . . . . . . . . . . . . . . . 32

ICEL Inside Corner Elliptical . . . . . . . . . . . . . . . . 33

ICRA Inside Corner Radiused . . . . . . . . . . . . . . . 34

ICRD Inside Corner Round . . . . . . . . . . . . . . . . . 35

ICRF Inside Corner Flange . . . . . . . . . . . . . . . . . 36

ICSQ Inside Corner Square . . . . . . . . . . . . . . . . . 37

CHFS Channel Flush Square . . . . . . . . . . . . . . . . . 38

CHRS Channel Rectangular Square . . . . . . . . . . . . 39

CHSA Channel Square Angled . . . . . . . . . . . . . . . 40

CHST Channel Square Tapered . . . . . . . . . . . . . . 41

IBRR Insert Blade Rectangular Round . . . . . . . . . 42

IBRS Insert Blade Rectangular Square . . . . . . . . . 43

IBRT Insert Blade Rectangular Tapered . . . . . . . . 44

IPRS Insert Projecting Radiused Square . . . . . . . 45

IRSQ Insert Rectangular Square . . . . . . . . . . . . . 46

MCR C Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

MFR F Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

MJR J Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

MKE Knife Edge . . . . . . . . . . . . . . . . . . . . . . . . . 50

MWR W Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

TA

BLE O

F C

ON

TEN

TS

Creates minimalist shadow line with simple reveal

space that allows installa�on ver�cally, horizontally

or diagonally. Can be used in conjunc�on with 5/8”

drywall, panel installa�on and wrapped surface

finishes such as fabric or vinyl wall coverings. Ridged

faces for tape and float. Available in 10' length.

6063 T5 aluminum with standard clear anodized or

primed finish. Anodized color and powder coa�ng

finishes available with custom color matching.

RV

R

EV

EA

L

4

Drywall

Metal Stud

Drywall

Metal Stud

ITEM ID

RV-12

RV-100

RV-200

"A" (REVEAL)

1/2"

1"

2"

"A"

5/8"

Tape & Float

XtremeInterior profiles are subject to alterations without notice or notification.

RV

DF R

EV

EA

L D

OU

BLE F

LA

NG

E

5

Drywall

Metal Stud

ITEM ID

RVDF-12

RVDF-100

RVDF-200

"A" (REVEAL)

1/2"

1"

2"

3/8""A"

5/8"

Drywall

Metal Stud

Creates sleek shadow line with simple reveal space

and double flange arms. Can be installed

ver�cally, horizontally or diagonally. Used in

conjunc�on with 5/8” drywall, panel installa�on

and wrapped surface finishes such as fabric or

vinyl wall coverings. Available in 10' length.





RV

RD

R

EV

EA

L R

OU

ND

6

Drywall

Metal Stud

Drywall

Metal Stud

ITEM ID

RVRD-12

RVRD-100

RVRD-200

"A" (REVEAL)

1/2"

1"

2"

3/8" "A"

5/8"

Creates an appealing recess with projec�ng details

that allows installa�on ver�cally, horizontally or

diagonally. Can be used in conjunc�on with 5/8”


finishes such as fabric or vinyl wall coverings.

Available in 10' length.





RV

RS R

EV

EA

L S

QU

AR

E

Drywall

Metal Stud

Drywall

Metal Stud

7

ITEM ID

RVRS-12

RVRS-100

RVRS-200

"A" (REVEAL)

1/2"

1"

2"

3/8""A"

5/8"

Creates an appealing recess with projec�ng square

details that allows installa�on ver�cally, horizontally









RV

SA

REV

EA

L S

QU

AR

E A

NG

LED

8

Drywall

Metal Stud

Drywall

Metal Stud

ITEM ID

RVSA-12

RVSA-100

RVSA-200

"A" (REVEAL)

1/2"

1"

2"

3/8" "A"

5/8"

Creates an appealing recess with projec�ng angled

details that allows installa�on ver�cally,

horizontally or diagonally. Can be used in


and wrapped surface finishes such as fabric or






RV

ST

REV

EA

L S

QU

AR

E T

APER

ED

9

Drywall

Metal Stud

Drywall

Metal Stud

ITEM ID

RVST-12

RVST-100

RVST-200

"A" (REVEAL)

1/2"

1"

2"

3/8""A"

5/8"

Creates an appealing recess with projec�ng

tapered details that allows installa�on ver�cally,

horizontally or diagonally. Can be used in


and wrapped surface finishes such as fabric or vinyl

wall coverings. Available in 10' length.





RV

V R

EV

EA

L V

10

Drywall

Metal Stud

Drywall

Metal Stud

3/4"

5/8"

Tape & Float

Creates unique shadow line with v shaped reveal

space that allows installa�on ver�cally, horizontally



finishes such as fabric or vinyl wall coverings. Ridged

faces for tape and float. Available in 10' length.





RV

VF R

EV

EA

L V

FLA

NG

E

11

Drywall

Metal Stud

Drywall

Metal Stud

3/4"

5/8"

3/8"

Creates beau�ful shadow line with v shaped reveal

space and double flanges. Can be installed

ver�cally, horizontally or diagonally. Used in


and wrapped surface finishes such as fabric or vinyl

wall coverings. Available in 10' length.





Drywall

Metal Stud

Metal Stud

Tape & Float

Drywall

BPR

BA

SE P

RO

JEC

TIN

G R

OU

ND

12

ITEM ID

BPR-34

BPR-150

BPR-200

BPR-250

"A" (LENGTH)

3/4"

1-1/2"

2"

2-1/2"

"A"

3/8"

Patent Pending

Stunning profile that creates a recessed base at the

bo�om of a wall just above floor surface or at the

top of a wall just below the ceiling surface.

Projec�ng round edge adds beau�ful detail to any

space. Ridged face provided for taping and

floa�ng. Can be used in conjunc�on with wrapped

surface finishes such as fabric or vinyl wall

coverings. Used horizontally. Available in 10' length.




5/8"


Drywall

Metal Stud

Metal Stud

Tape & Float

Drywall

BPR

R B

ASE P

RO

JEC

TIN

G R

OU

ND

REV

EA

L

13

ITEM ID

BPRR-250

BPRR-300

"A" (LENGTH)

2-1/2"

3"

"A"

5/8"

3/8"

Patent Pending

Unique profile that creates a combina�on reveal

and projec�ng detail line at the bo�om of a wall

just above floor surface or at the top of a wall just

below the ceiling surface. Projec�ng round edge

adds classic and refined detail. Ridged face

provided for taping and floa�ng. Can be used in

conjunc�on with wrapped surface finishes such as

fabric or vinyl wall coverings. Used horizontally.





5/8"


Drywall

Metal Stud

Metal Stud

Tape & Float

Drywall

BPS

BA

SE P

RO

JEC

TIN

G S

QU

AR

E

14

ITEM ID

BPS-34

BPS-150

BPS-200

BPS-250

"A" (LENGTH)

3/4"

1-1/2"

2"

2-1/2"

"A"

3/8"

Patent Pending

Sleek profile that creates a recessed base at the


top of a wall just below the ceiling surface.

Projec�ng square edge adds classic and refined

detail. Ridged face provided for taping and floa�ng.

Can be used in conjunc�on with wrapped surface

finishes such as fabric or vinyl wall coverings. Used

horizontally. Available in 10' length.




5/8"


Metal Stud

Tape & Float

Drywall

15

ITEM ID

BPSR-250

BPSR-300

"A" (LENGTH)

2-1/2"

3"

"A"

5/8"

3/8"

Drywall

Metal Stud

BPSR

BA

SE P

RO

JEC

TIN

G S

QU

ARE R

EV

EA

L

Patent Pending

Unique profile that creates a combina�on reveal

and projec�ng detail line at the bo�om of a wall

just above floor surface or at the top of a wall just

below the ceiling surface. Projec�ng square edge

adds classic and refined detail. Ridged face

provided for taping and floa�ng. Can be used in


fabric or vinyl wall coverings. Used horizontally.





5/8"


Drywall

Metal Stud

Drywall

Metal Stud

BR

DF

BA

SE R

EV

EA

L D

OU

BLE F

LA

NG

E

16

Striking profile that creates a recessed base at the


top of a wall just below the ceiling surface. Double

flange creates a reveal for visual impact as well as

protec�ng the bo�om of wall material and crea�ng

a lower recess. Can be used in conjunc�on with

wrapped surface finishes such as fabric or vinyl wall





2-1/8"

1/2"

3/8"

3/8"

5/8"


Drywall

Metal Stud

Drywall

Metal Stud

Tape & Float

BR

F B

ASE R

EV

EA

L F

LA

NG

E

17

Uniquely detailed profile that creates a recessed

base at the bo�om of a wall just above floor

surface or at the top of a wall just below the ceiling

surface. Adding a decora�ve flange as well as a

reveal. Ridged face provided for taping and floa�ng.







1-7/8"

5/8"

1/2"

5/8"


Metal Stud

Drywall

Metal Stud

Drywall

BR

L

BA

SE R

EV

EA

L L

ED

GE

18

Tape & Float

Classic profile that creates a recessed base at the


top of a wall just below the ceiling surface with

addi�onal reveal space created by projec�ng edge.

Projec�ng linear edge adds streamlined detail to

any room. Ridged face provided for taping and







1-3/16"

1/2"

5/8"


BSL B

ASE S

HA

DO

W L

INE

Drywall

Metal Stud

Drywall

Metal Stud

Tape & Float

19

ITEM ID

BSL-516

BSL-58

BSL-150

BSL-400*

"A" (LENGTH)

5/16"

5/8"

1-1/2"

4"

*BSL-400 also available for 1/2" drywall

Create visually stunning shadow lines with a

minimalist base trim that allows the wall to appear

to float just above the floor surface and allows for

the same effect at the top of the wall just below

the ceiling surface. Can be used ver�cally or

horizontally. Ridged face provided for taping and



coverings. Available in 10' length.




"A"

5/8"


CA

C C

OR

NER

AR

C

20

Metal Stud

Metal Stud

Drywall

Drywall

Simple but stunning corner profile. Provides corner

protec�on and simple design for ver�cal and

horizontal drywall or panel corners. Can be used in


fabric or vinyl wall coverings. Available in 10'

length.




5/8"


CBD

CO

RN

ER

BEA

D

21

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

R .056"

Minimalis�c bead line corner profile. Provides

corner protec�on and sleek design for ver�cal

drywall or panel corners. Can be used in


fabric or vinyl wall coverings. Available in 10'

length.





CBV

C

OR

NER

BEV

EL

22

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

"A"

ITEM ID

CBV-100

CBV-200

"A" (BEVEL)

1"

2"

Modern and modest beveled corner profile.

Provides corner protec�on and streamlined design

for ver�cal or horizontal drywall or panel corners.








CEL C

OR

NER

ELLIP

TIC

AL

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

23

Patent Pending

Design feature with ellip�cal corner for ver�cal and

horizontal (for fur-down applica�ons) drywall or

panel corners. Can be used in conjunc�on with


coverings. Unique design with stunning visual

results. Provides corner protec�on and reveal

creates the illusion of a floa�ng corner. Ridged faces

provided for taping and floa�ng. Available in 10'

length.




1/4"

1-1/2"

5/8"


CR

A C

OR

NER

RA

DIU

SED

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

24

Patent Pending

Design feature with rounded edge for ver�cal and




coverings. Provides corner protec�on and reveal



length.




1/4"

5/8"

1-1/8"


CR

D C

OR

NER

RO

UN

D

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

25

Patent Pending

Design feature with circular corner for ver�cal and







length.




1/4"

R .50"

5/8"


CR

R

C

OR

NER

REC

TA

NG

ULA

R R

AD

IUSED

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

26

Patent Pending

Design feature with rounded asymmetrical corner

for ver�cal and horizontal (for fur-down applica�ons)

drywall or panel corners. Can be used in conjunc�on

with wrapped surface finishes such as fabric or vinyl

wall coverings. Provides corner protec�on and reveal



length.




2-5/8"

1/4"

1-1/8"5/8"


CR

S C

OR

NER

REC

TA

NG

ULA

R S

QU

AR

E

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

27

Patent Pending

Design feature with asymmetrical corner for ver�cal

and horizontal (for fur-down applica�ons) drywall or






length.




2-5/8"

1/4"

5/8"


CR

T

C

OR

NER

REC

TA

NG

ULA

R T

APER

ED

Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

28

Patent Pending

Design feature with tapering asymmetrical corner for

ver�cal and horizontal (for fur-down applica�ons)

drywall or panel corners. Can be used in conjunc�on


wall coverings. Provides corner protec�on and reveal



length.




2-5/8"

1/4"

1-1/8"5/8"


Metal Stud

Metal Stud

Drywall

Drywall

Tape & Float

CSQ

CO

RN

ER

SQ

UA

RE

29

Patent Pending

Design feature and finished edge for ver�cal and

horizontal (for fur-down applica�ons) drywall or panel

corners. Can be used in conjunc�on with wrapped

surface finishes such as fabric or vinyl wall coverings.

Provides corner protec�on and reveal creates the

illusion of a floa�ng corner. Ridged faces provided for

taping and floa�ng. Available in 10' length.




1/4"1-1/8"

5/8"


CXF C

OR

NER

X

30

Metal Stud

Drywall

ITEM ID

CXF-14

CXF-38

CXF-100

"A" (FLANGE)

1/4"

3/8"

1"

Metal Stud

Drywall

Classic and clean corner profile with flange arms.

Provides corner protec�on and beau�ful design for

ver�cal and horizontal drywall or panel corners.







"A"

5/8"


ICA

C IN

SID

E C

OR

NER

AR

C

31

Metal Stud

Drywall

Tape & Float

Drywall

Metal Stud

ITEM ID

ICAC-100

ICAC-200

"A" (RADIUS)

1"

2"

"A"

Coordina�ng inside corner for the CAC profile. Can be

used ver�cally and horizontally in conjunc�on with

drywall, panels, and wrapped surface finishes. Ridged

faces allow for taping and floa�ng. Available in 10'

length.





ICBV

INSID

E C

OR

NER

BEV

EL

32

Metal Stud

Drywall

Tape & Float

Drywall

Metal Stud

ITEM ID

ICBV-100

ICBV-200

"A" (BEVEL)

1"

2"

"A"

Coordina�ng inside corner for the CBV profile. Can

be used ver�cally and horizontally in conjunc�on

with drywall, panels, and wrapped surface finishes.

Ridged faces allow for taping and floa�ng.






ICEL IN

SID

E C

OR

NER

ELLIP

TIC

AL

Tape & Float

33

Drywall

Metal Stud

Metal Stud

Drywall

Patent Pending

Coordina�ng inside corner for the CEL profile. Can








1-1/2"

1/4"


ICR

A

IN

SID

E C

OR

NER

RA

DIU

SED

Metal Stud

Drywall

Tape & Float

34

Drywall

Metal Stud

Patent Pending

Coordina�ng inside corner for the CRA profile. Can








1/4" 1-1/8"


ICR

D IN

SID

E C

OR

NER

RO

UN

D

Metal Stud

Drywall

Tape & Float

35

Drywall

Metal Stud

Patent Pending

Coordina�ng inside corner for the CRD profile. Can








1/4"

R .50"


ICR

F

IN

SID

E C

OR

NER

FLA

NG

E

36

Metal Stud

Drywall

Drywall

Metal Stud

Coordina�ng inside corner for the CXF profile. Can



Tape and float unnecessary due to flange detail.





3/8"

5/8"


ICSQ

INSID

E C

OR

NER

SQ

UA

RE

Metal Stud

Drywall

Tape & Float

37

Drywall

Metal Stud

Patent Pending

Coordina�ng inside corner for the CSQ profile. Can








1/4"1-1/8"


Drywall

Metal Stud

Tape & Float

Drywall

Metal Stud

CH

FS

C

HA

NN

EL F

LU

SH

SQ

UA

RE

38

5/8"

Patent Pending

Anchor channel for two piece system. Ridged faces

provided for taping and floa�ng and allow insert

piece to appear to stand alone. Can be used in

conjunc�on with 5/8" drywall or panel installa�on

and with wrapped surface finishes such as fabric or

vinyl wall coverings. Used ver�cally or diagonally

and in approved condi�ons, horizontally. Available

in 10' length.





Drywall

Metal Stud

Drywall

Metal Stud

CH

RS C

HA

NN

EL R

EC

TA

NG

ULA

R S

QU

AR

E

5/8"

39

3/8"

Patent Pending


provided for taping and floa�ng and classic square

projec�ons add visual impact when paired with an

insert piece. Can be used in conjunc�on with 5/8"

drywall, panel installa�on and with wrapped surface


ver�cally or diagonally and in approved condi�ons,






Drywall

Metal Stud

Drywall

Metal Stud

CH

SA

CH

AN

NEL S

QU

AR

E A

NG

LED

40

5/8"

3/8"

Patent Pending


provided for taping and floa�ng and angled detail adds

a unique touch to a classic look. Can be used in

conjunc�on with 5/8" drywall, panel installa�on and


wall coverings. Used ver�cally or diagonally and in

approved condi�ons, horizontally. Available in 10'

length.

6063 T5 aluminum with standard clear anodized or primed finish. Anodized color and powder coa�ng finishes available with custom color matching.


Drywall

Metal Stud

Drywall

Metal Stud

CH

ST

CH

AN

NEL S

QU

AR

E T

APER

ED

5/8"

3/8"

41

Patent Pending


provided for taping and floa�ng and unique tapered

square edges create a dynamic look when paired

with an insert piece. Can be used in conjunc�on with

5/8" drywall, panel installa�on and with wrapped

surface finishes such as fabric or vinyl wall coverings.

Used ver�cally or diagonally and in approved

condi�ons, horizontally. Available in 10' length.





Drywall

Metal Stud

Tape & Float

Drywall

Metal StudIBR

R

IN

SER

T B

LA

DE R

EC

TA

NG

ULA

R R

OU

ND

42

ITEM ID

IBRR-100

IBRR-200

IBRR-300

"A" (LENGTH)

1"

2"

3"

"A"

1/2"

Patent Pending

Paired with Channel Reveal this unique blade

projec�on creates an a�rac�ve look in any space.

Ridged faces provided for taping and floa�ng with

drywall installa�on. Can also be used in

conjunc�on with panels and wrapped surface


ver�cally or diagonally. Available in 10' length.





Drywall

Metal Stud

Tape & Float

Drywall

Metal Stud

IBR

S IN

SER

T B

LA

DE R

EC

TA

NG

ULA

R S

QU

AR

E

43

ITEM ID

IBRS-100

IBRS-200

IBRS-300

"A" (LENGTH)

1"

2"

3"

"A"

1/4"

Patent Pending

Paired with Channel Reveal this blade projec�on

with reveals adds refinement and class. Ridged

faces provided for taping and floa�ng with drywall

installa�on. Can also be used in conjunc�on with

panels and wrapped surface finishes such as fabric

or vinyl wall coverings. Used ver�cally or diagonally.






Drywall

Metal Stud

Tape & Float

Drywall

Metal StudIBR

T

IN

SER

T B

LA

DE R

EC

TA

NG

ULA

R T

APER

ED

44

ITEM ID

IBRT-100

IBRT-200

IBRT-300

"A" (LENGTH)

1"

2"

3"

"A"

1/2"

Patent Pending

Paired with Channel Reveal this exclusive projec�on

creates an impressive look with a detailed notch blade.

Ridged faces provided for taping and floa�ng with

drywall installa�on. Can also be used in conjunc�on

with panels and wrapped surface finishes such as fabric

or vinyl wall coverings. Used ver�cally or diagonally.






Drywall

Metal Stud

Tape & Float

Drywall

Metal Stud

IPR

S IN

SER

T P

RO

JEC

TIN

G R

AD

IUSED

SQ

UA

RE

45

ITEM ID

IPRS-0

IPRS-100

IPRS-200

IPRS-300

"A" (LENGTH)

0"

1"

2"

3"

"A"

5/16"

Paired with Channel Reveal this subtle projec�on

creates a classic look in drywall or panel



coverings. Ridged faces provided for taping and

floa�ng. Used ver�cally or diagonally. Available in

10' length.





Drywall

Metal Stud

Tape & Float

Drywall

Metal Stud

IRSQ

INSER

T R

EC

TA

NG

ULA

R S

QU

AR

E

"A"

3/4"

46

ITEM ID

IRSQ-0

IRSQ-100

IRSQ-200

IRSQ-300

"A" (LENGTH)

0"

1"

2"

3"

Paired with Channel Reveal this classic projec�on

creates a modern look in drywall or panel



coverings. Ridged faces provided for taping and

floa�ng. Used ver�cally or diagonally.






MC

R C

MO

LD

47

Drywall

Metal Stud

Tape & Float

Ceiling

Metal Stud

Ceiling

Drywall

Clean finish design with reveal detail for drywall

termina�ons at ceilings, windows, doors and other

material transi�ons. Can be installed horizontally or

ver�cally. Can be used in conjunc�on with 5/8"

drywall, panel installa�on and with wrapped






1"

5/8"


MFR

F M

OLD

48

Drywall

Metal Stud

Ceiling

Metal Stud

Ceiling

Drywall

Clean finish design with reveal detail for drywall

termina�ons at ceilings, windows, doors and other

material transi�ons. Can be installed horizontally

or ver�cally. Can be used in conjunc�on with 5/8"







1"

3/8"

5/8"


MJR

J MO

LD

49

ITEM ID

MJR-14

MJR-38

MJR-50

"A" (FLANGE)

1/4"

3/8"

1/2"

Metal Stud

Drywall

Metal Stud

Drywall

Classic and clean design provides smooth finish at

edges of drywall or at material transi�ons. Can be

installed horizontally or ver�cally. Can be used in

conjunc�on with 5/8" drywall, panel installa�on

and with wrapped surface finishes such as fabric or





"A"

5/8"


MK

E K

NIF

E E

DG

E

50

Fur down

Ceiling

Tape & Float

ITEM ID

MKE-30

MKE-45

"A" (ANGLE)

30°

45°

"A"

Wall

"B"

"B"

1-3/8"

3/4"

Wall

Ceiling

Creates a sharp 'knife edge' at ceiling drywall

termina�ons. Clean, crisp look crea�ng unique

ceiling design and allows for LED ligh�ng or shadow

line. Can be used in conjunc�on with 5/8" drywall,

panel installa�on and with wrapped surface







MW

R W

MO

LD

51

Drywall

Metal Stud

Ceiling

ITEM ID

MWR-516

MWR-58

MWR-150

"A" (REVEAL)

5/16"

5/8"

1-1/2"

5/8"

"A" 3/4"

Metal Stud

Ceiling

Drywall

Streamlined design with reveal detail for drywall

termina�ons at ceilings and other material

transi�ons. Can be used in conjunc�on with 5/8"








CLEAR

CHAMPAGNE

LIGHT BRONZE

MEDIUM BRONZE

DARK BRONZE

BLACK

*Anodized color options shown above.

XtremeInterior™ extruded profiles are provided standard with a primed finish using a proprietary primer suitable for field painting using most paint materials. Ideal application is with a direct to metal alkyd enamel. Consult your local paint manufacturers for best practice and proper paint selection and application. Custom color powder coating available upon request (minimum applies).

All anodized finishes are provided within an industry range of color consistency and can vary slightly from item to item. Special order anodized colors are subject to specific quantity minimums by item. Anodizing is an electrochemical conversion process that deposits an oxide film on the aluminum profile. A natural oxidation process occurs on all bare aluminum, however, producing the oxidation process artificially through anodizing creates a thicker, harder, and more durable oxide film which is an extremely durable finish resistant to most forms of airborne corrosion.

xi technical guide · 2018. 10. 18. · rvdf reveal double flange 5 drywall metal stud item id...

Documents