x360glitchip v2 installation[en]

14
Version 2.0+ How To Install http://www.x360glitchip.com

Upload: julh-ballys

Post on 14-Apr-2015

226 views

Category:

Documents


29 download

TRANSCRIPT

Page 1: x360Glitchip v2 Installation[en]

Version 2.0+

How To Install

http://www.x360glitchip.com

Page 2: x360Glitchip v2 Installation[en]

Version 2 Description

The version 2 brings you a lot of new features and wants to be modable as you need depending of your Xbox.

These points concern Both SLIM and FAT

These points concern SLIMs

These points concern FAT (FAT1 & FATX For Xenon, FAT1 & FAT2 For other revisions)

Choose your capacitor (270pF For Xenon, 330pF Or 390pF For Slims)

Timings Configurations (Choose the good value for YOUR Xbox. 65 being the reference value). These

points concern only SLIMS and XENON. They are useless for other revisions.

Handle Double Nand (Ref to the last chapter)

JTAG Port. Use pin header and our x360JtU to Flash your modchip through our 360gcProg Software.

Timing Points.

Wires are provided with the chip. Use followings :

- 3.3v Use the 10cm lenght wire and adapt depending the chosen point.

- GND Use the AWG-22 Wire and adapt the length depending of the MB revision

- A Use the wire 4.5cm length for SLIM, and 10cm for FAT

- F Use the red wire 38cm for SLIM, 10cm for FAT

- D and E, Use wires of 5cm length

- C Use the 10cm length wire

WARNING : If your chip is NOT YET FLASHED, Refer to the manual « How to flash your x360glitchip »

before continue.

Page 3: x360Glitchip v2 Installation[en]

Install on XboX 360 SLIM (1/4)

Wires points are : R2F9 ����3.3v (7cm) ROL ����GND (13cm) J2C3.10 ���� D (5cm) J2C3.9 ���� E (5cm)

These points are under the motherboard : FT5R2 ���� A (4.5cm) – Provided wire is red FT4R2 ���� F (38cm) – Provided wire is red

R2F9 ����3.3v ROL ����GND J2C3.9 ���� E J2C3.10 ���� D

3.3v sur U4E1 ou U4E2 ou R2F9

(The last one is the better one)

Page 4: x360Glitchip v2 Installation[en]

Install on XboX 360 SLIM (2/4)

Here Diagram for Trinity : FT5R2 ���� A (4.5cm) FT4R2 ���� F (38cm) Use the same hole to get the twos wires on the top of the motherboard Use the 2 reds wires

Page 5: x360Glitchip v2 Installation[en]

Install on XboX 360 SLIM (3/4)

Here Diagram for Corona : FT5R2 ���� A (4.5cm) C5R11-R ���� F (55cm) Or P4P5. Use the same hole to get the A wire on the top of the motherboard, and the big one for the F wire. Use the red wire for A, Use an AWG-25 wire for F

You can place the F wire like this :

Page 6: x360Glitchip v2 Installation[en]

Install on XboX 360 SLIM (4/4)

Here a complete installation of the chip for Trinity

Wire F of 38cm coming

from motherboard and

goes make a loop of the

ventirad

Wire F of 38cm which

finish the loop and goes to

the chip

Page 7: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT =< 14699 (1/4)

Wires points are : J2B1.7 ����3.3v (5cm = adapt the lenght) J2B1.12 ����GND (4cm= adapt the lenght) J8C1.2 ���� F (10cm = adapt the lenght)

These points are under the motherboard : FT6U7 ���� A (10cm = adapt the lenght) Under R7R17 ���� C (10cm = adapt the lenght)

J2B1.7 ����3.3v J2B1.12 ����GND

J8C1.2 (Except Xenon) ���� F

Page 8: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT =< 14699 (2/4)

Under R7R17 ���� C

FT6U7 ���� A Remove C7R112 and solder on the right pad of C7R112 (Only for Xenon) ���� F

Page 9: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT =< 14699 (3/4)

Here a complete installation of the chip

Page 10: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT =< 14699 (4/4)

Page 11: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT >= 14717 (1/3)

Wires points are : J2B1.7 ����3.3v (5cm = adapt the lenght) J2B1.12 ����GND (4cm= adapt the lenght) J8C1.2 ���� F (10cm = adapt the lenght) J2B1.9 ���� E (5cm = adapt the length) // J2B1.10 ���� D (5cm = adapt the length)

These points are under the motherboard : FT6U7 ���� A (10cm = adapt the lenght)

J2B1.7 ����3.3v // J2B1.12 ����GND J8C1.2 ���� F

J2B1.9 ����E // J2B1.10 ���� D

Page 12: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT >= 14717 (2/3)

FT6U7 ���� A

Page 13: x360Glitchip v2 Installation[en]

Install on XboX 360 FAT >= 14717 (3/3)

Some modifications are needed on the chip :

With your x360Glitchip v2.1, you have also recieved 2 littles resistors which are dedicated to the RGH2

installation.

Use the BLACK one (10ohm) on the F point.

User the RED one (3.3kohm) between the timing point and the C10 point like showed on the following picture :

Some littles advices :

- Position and lenght of the F wire are VERY IMPORTANT in order to get a good RGH. If you see that the reset

(Red Light) are irregular, change the length and the position of this file.

- Quality of GROUND is VERY important, double it, and think to connect the video cable and TURN ON your TV

before booting your Xbox.

- Quality of wires are also important. Specialy for RGH2, take a little bigger section of cable like AWG-25 and use

Stranded Wires.

3.3 kOhm

10 Ohm

Page 14: x360Glitchip v2 Installation[en]

Double Nand Feature

The x360Glitchip v2 brings you the possibility to be unactive when using a double nand addon.

For that, you have to solder the wire which used as Signal Command on the DN pad of the chip. Then, you

have to solder the pads to indicate where the Freeboot Glitch nand is installed.

If you solder the I Pads, your glitched nand is on the INTERNAL nand

If you solder the E, your glitched nand is on the EXTERNAL nand (On your Double Nand Addon)

We strongly recommands you to install the Glitched one on the INTERNAL nand and the Retail one on the

EXTERNAL nand.