7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter Jr.’s IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

7.4 4-pin peripheral connector.

7. Identify the power supply connectors:

7.1 20/24 pin ATX connector.

7.2 ATX 12V P4 CPU connector.

7.3 Serial ATA (SATA) connector.

7.5 6-pin PCI-Express connector.

7.6 Floppy drive connector.

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr.

CONTENT

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove PCI slot covers. Firmly press point A with thumb, while pull- ing point B with index finger and open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage the locking mechanism. No screws are necessary, but can be used optionally on optical and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 In addition to fans included, you may opt to install an 8 or 12cm ‘blowhole’ fan. In the above pic- ture, the arrows indicate which holes to use for mounting a 12cm fan.

4.2 Inside the chassis, mount fan to the underside of ‘blowhole’ area and screw into place. Make sure the top vent is in the ‘Open’ posi- tion to allow warm air to escape.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

2. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripheral connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Inside the chassis, mount fan to the underside of ‘blowhole’ area and screw into place. Make sure the top vent is in the ‘Open’ posi- tion to allow warm air to escape.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter Jr.’s IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

7.4 4-pin peripheral connector.

7. Identify the power supply connectors:

7.1 20/24 pin ATX connector.

7.2 ATX 12V P4 CPU connector.

7.3 Serial ATA (SATA) connector.

7.5 6-pin PCI-Express connector.

7.6 Floppy drive connector.

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr.

CONTENT

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter's IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.2 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

2.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

2.1 20/24 pin ATX connector x 1

2.2 ATX 12V P4 connector x 1

2.3 Serial ATA (SATA) connector x 4

2.5 6-pin PCI-Express connector x 1

2.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace screws. Congratulations! You’ve completed assembly of the X-Jupiter Jr.

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter Jr.’s IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

7.4 4-pin peripheral connector.

7. Identify the power supply connectors:

7.1 20/24 pin ATX connector.

7.2 ATX 12V P4 CPU connector.

7.3 Serial ATA (SATA) connector.

7.5 6-pin PCI-Express connector.

7.6 Floppy drive connector.

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr.

CONTENT

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter Jr.’s IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

7.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

7.1 20/24 pin ATX connector x 1

7.2 ATX 12V P4 connector x 1

7.3 Serial ATA (SATA) connector x 4

7.5 6-pin PCI-Express connector x 1

7.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr.

CONTENT

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings on the leads indicate positive wires.

6.2 Locate front panel leads. The LED leads are located near the right-side panel. The Power/Reset/Speaker leads can be accessed by removing the left panel. Refer to your motherboard’s document- ation for placement schematics.

(Remove right-side panel to better access wiring.)

5.3 Place the probe labeled ‘HDD’ to the hard-drive’s surface. Use thermal tape for best results.

Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

5.5 Monitor system temperatures from the front panel LCD.

8

Connect PC components to the required power connector for each device type.

6

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any ‘fin’ on the CPU’s heatsink and tape in place. Thermal tape should be used for best results.

5.1 Locate the device temperature probes.

4

3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch.

2.5 Align rails with hard-drive bay and insert.

3. Install PCI components:

2

1.4 If your motherboard included an IO shield, you must remove the X-Jupiter Jr.’s IO shield. Use thumbs or other object to push shield in- ward (cover area with a cloth to avoid injury from metal edges!).

1.6 Put brass standoffs in place. Align motherboard with standoffs and mount to case. This ATX mother- board (12”x8.3”) only used notches A1-A6. M8 was also used since it lined up.

1.5 Refer to the motherboard holes index for standoff placement for your motherboard type. A full ATX (12”x9.6”) board will use notches A1-A9. Some mother- boards may not use all notches. Use any notches that line up with your motherboard.

NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward.

2.4 Attach 1 mounting rail to each side of each hard-disk drive.

2.2 For 5 1/4” drives, align the device with the drive bay and insert. Do the same for 3 1/2” drives using the lower drive bays.

2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

Screwdriver OPTIONAL!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the rear of the X-Jupiter Jr.

1.3 Likewise for the window version, grab the notch on the left panel and pull until the panel releases. Remove panel.

NOTE: CPU and memory installation is not covered in this manual. Please refer to each components’ documentation for instructions.

25cm Fan versionWindow version

1. Motherboard installation..................................1

2. Install 3½” and 5¼” drives..............................3

3. Install PCI components.................................4

5. Temperature probe setup........................6

6. ...........7 Connect case leads to motherboard

7. ..............8Identify the power supply connectors

8. Complete the installation............................9

4. Case fan setup...........................................5

9. USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.).

4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’. The connector labeled ‘INPUT’ is then plugged into the power supply.

4.2 Use the fan controller knob on the front panel to regulate the air-flow of case fans.

4. Case fan setup:

2. Install 3½” and 5¼” drives:

7.4 4-pin peripheral connector x 6

7. Identify the power supply connectors:

7.1 20/24 pin ATX connector x 1

7.2 ATX 12V P4 connector x 1

7.3 Serial ATA (SATA) connector x 4

7.5 6-pin PCI-Express connector x 1

7.6 Floppy drive connector x 2

3.4 Once the card is seated firmly, return latch to the initial position. A ‘click’ will be heard when fully engaged.

5.4 Locate the LCD power connector. (A black/red wire having a male and female 4-pin connector.) Plug the male end to a peripher- al connector on the power supply.

X-Jupiter Jr. Finished Appearance.

1.2 Grab the notch on the left panel. Pull until the panel is released and remove.

8. Complete the installation:

8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr.

CONTENT