www.timber.org.au timber in internal applications material basics timber and wood products basic...
TRANSCRIPT
www.timber.org.au
timber in internal applications
Material Basics
Timber and Wood Products
Basic material properties and characteristics.
www.timber.org.au
timber in internal applications
Material Basics
The nature of timber
• Timber is a natural product, drawn from the wood in the trunks of trees.
• Its character is consistent with the species of tree and the form and growth over time of the wood in it.
Regrowth in a native forest
www.timber.org.au
timber in internal applications
Material Basics
Tree growth• New wood on outside of tree
– oldest wood on the inside– youngest wood on the outside– diameter largest at the base– one ring (layer) per growing season
• Tree in forest grows toward light– trunk is straight– lower branches die– leaving small knots in wood
• Bark protects wood from damage– the tree sheds bark each year
www.timber.org.au
timber in internal applications
Material Basics
Production of wood
Cambium - growth cells• wood cells created on the inside• bark cells created on the outside
Sapwood - newest wood• on the outside of tree (~ 1-3 cm)• takes nutrients from root to leaves
Heartwood - older wood• cells closed - can’t pass nutrients • storage for waste - extractives
Pith - the start of growth in the tree• the original sapling
www.timber.org.au
timber in internal applications
Material Basics
Variation: fibre & grain
• The cell structure is designed to serve particular functions in a tree.
• Its properties vary in different directions.
rays
rays
cells
fibres
vesselshardwood earlywood
rays
latewood
softwood
www.timber.org.au
timber in internal applications
Material Basics
Variation: species & growth
• Species and genetics: – selected stock or
natural seed.
• Climate:– wet or dry, cold or
warm.
• Arrangement:– native forest or
plantation.
www.timber.org.au
timber in internal applications
Material Basics
Each piece is unique
Myrtle burl veneer
Quarter sawn hardwood
www.timber.org.au
timber in internal applications
Material Basics
Properties are variable
• Drying (seasoning) & shrinkage
• Strength & hardness
• Durability
• Appearance
www.timber.org.au
timber in internal applications
Material Basics
Moisture and drying in wood cells
removed bound waterSeasoned
timber15% MC
100% MC
Unseasoned timber
Growingtree
free water
25% MC
fibre saturation
bound waterPartially seasoned
timber
www.timber.org.au
timber in internal applications
Material Basics
Benefits of drying
• Drying timber increases its:– strength; – stiffness; – stability– durability; &– ease of fastening.
• It is ideally dried to a moisture content in equilibrium with its service environment.
Checking the moisture content
www.timber.org.au
timber in internal applications
Material Basics
Timber shrinks as it dries
• It shrinks at different rates in different directions.
• Once dry, it will expand & contract to be in equilibrium with changing local conditions.
Shrinkage from 12% to 25% MC
Radiata pine Rad 3.5% Tang 4%Hoop pine Rad 2.5% Tang 3.5%Cypress Rad 3.5% Tang 4%
Spotted gum Rad 4.5% Tang 6%Karri Rad 4.5% Tang 10%Sydney blue gumRad 5% Tang 9%Grey Ironbark Rad 5.5% Tang 7.5%Mountain ash Rad 6.5% Tang 13%
So
ftwo
od
Ha
rdw
ood
Tangential shrinkage
Radialshrinkage
Longitudinalshrinkage
www.timber.org.au
timber in internal applications
Material Basics
Shrinkage in sawn sections
• Tangential shrinkage is the highest;
• So, the growth rings tend to shorten as the timber dries.
www.timber.org.au
timber in internal applications
Material Basics
Timber dries at different rates
• Pines have a porous cell structure:– They can be dried very quickly.– Turnaround time from saw to store can
be as low as a week.
• Hardwoods have a non-porous cell structure:– The moisture must diffuse through the
cell wall.– Drying can be very slow.– It must be done carefully.
www.timber.org.au
timber in internal applications
Material Basics
Grain, strength & stiffness
Direction of grain
Strong parallel to grain & stiff parallel to grain
Weak perpendicular to grain
Properties of the grain
www.timber.org.au
timber in internal applications
Material Basics
Summary of characteristics
• Timber is a natural material • Each piece is unique in fibre, texture and
colour• Its strength is dependant on the
properties of the wood and the slope of the grain
• It takes up and gives up moisture• It expands and shrinks as it does so• It deteriorates in line with exposure
www.timber.org.au
timber in internal applications
Material Basics
Timber products
• Timber is available in a wide range of products and species including: – Solid sawn, moulded and laminated timber;– Veneer;– Plywood; and– Wood panels.
www.timber.org.au
timber in internal applications
Material Basics
Timber products: sawn
• Hardwood or softwood.
• Solid timber cut from a log and dried.
• It is a versatile material used for moulding, frames and exposed structures.
• Size is restricted.
www.timber.org.au
timber in internal applications
Material Basics
Timber products: mouldings
• Hardwood or softwood.
• Solid seasoned timber milled to a wide variety of shapes.
www.timber.org.au
timber in internal applications
Material Basics
Timber products: glue laminated
• Small pieces of timber glued together to form a larger element.
• Used as both a structural and finishing element.
• Size is limited only by transport capacity.
bench top
beam
www.timber.org.au
timber in internal applications
Material Basics
Timber products: curved glulam
• Glue laminated material can be curved.
Curved bar
www.timber.org.au
timber in internal applications
Material Basics
Timber products: veneer
• Thin layers of solid wood sliced from a flitch or peeled from a log and dried.
• High quality material is used as a decorative finish.
• Lower grade material is used to make plywood, LVL and similar products.
Veneer leaf
www.timber.org.au
timber in internal applications
Material Basics
Timber products: plywood
• Layers of veneer glued together so that the grain direction alternates between layers.
• Usually produced in sheets.
• Very good in a structure, as a lining and as a flooring surface.
www.timber.org.au
timber in internal applications
Material Basics
Timber products: wood panels
• Panels made from wood or wood fibres bound together with glue, or other binder:– Particleboard– Medium Density
Fibreboard (MDF)– Hardboard– Core board
MDF sheet
www.timber.org.au
timber in internal applications
Material Basics
Appearance grading
• Production process of sorting products into groups with similar characteristics & properties.
• Timber identified by calling up a specific grade.
Visual grading
www.timber.org.au
timber in internal applications
Material Basics
Grading standards
• AS 1810-1995 Timber - Seasoned cypress pine - Milled products
• AS 2796-1999 Timber - Hardwood - Sawn and milled products
• AS 4785-2002 Timber - Softwood - Sawn and milled products
www.timber.org.au
timber in internal applications
Material Basics
AS 2796 Hardwood - Sawn & milled
• This standard defines the requirements for hardwood used for visual applications: architectural (flooring, etc), lining & cladding; &
• It is in two main sections: – product requirements; & – visual grades.
www.timber.org.au
timber in internal applications
Material Basics
Appearance grading - rules
• Establish permissible limits on: – gum vein – knot size & frequency (location unimportant)– splits, cracks, checks (size and frequency)– stain (colour), grain uniformity– utility: want, wane, cup, bow, spring, twist
www.timber.org.au
timber in internal applications
Material Basics
Grade range
• From select grade– uniform wood with
few natural features
• Through to high feature grade– including lively
natural feature as part of a desirable aesthetic.
www.timber.org.au
timber in internal applications
Material Basics
AS 2796 Hardwood - Sawn & milled
• Tolerances are established for the major product groups (not grades):– Joinery and dressed boards; – Strip and overlay flooring, mouldings, sawn
boards for feedstock; &– Light decking, lining boards, cladding, facia,
bargeboards.
www.timber.org.au
timber in internal applications
Material Basics
AS 2796 Part 1 - distortion
• Bow - depends on thickness
• Spring - dependent on width
• Twist - separate limits for less or more than 25 mm thick
• Cup - 1mm per 100 mm width
www.timber.org.au
timber in internal applications
Material Basics
AS 2796 Part 1
• No lyctid susceptible sapwood is allowed. (Lyctids are small wood eating insects.)
• MC anywhere in a piece must be between:– 9-14% for most products including flooring. – 8-13% for parquet & furniture components.
www.timber.org.au
timber in internal applications
Material Basics
AS 2796 Hardwood - Sawn & milled
• The standard recognises feature as a desirable visual characteristic;
• Therefore, distortion and machining tolerances are associated with product, not grade; &
• The timber can then be specified with the desired appearance for any function.
www.timber.org.au
timber in internal applications
Material Basics
AS 4785 Softwood - Sawn & milled
• Layout is similar to AS 2796 with product requirements & visual grades;
• Visual grades are Clear, Appearance, Select, Standard, Utility Grade;
• With radiata, there is a much greater use of industry grades; &
• Terms can vary between companies.
www.timber.org.au
timber in internal applications
Material Basics
Jointing
• Timber is a highly versatile material that can be shaped and joined easily.
Mortice and tenon Housed
Half housed
www.timber.org.au
timber in internal applications
Material Basics
Jointing methods
Overlap Fixing blocks
DowelBiscuit
www.timber.org.au
timber in internal applications
Material Basics
Conclusions
• Timber is a natural product.
• It has been used for centuries.
• Skilled use and understanding of the material can yield excellent results.