windows2003serverinstallationguiderev2.0 (1)

8/12/2019 Windows2003ServerInstallationGuiderev2.0 (1)

http://slidepdf.com/reader/full/windows2003serverinstallationguiderev20-1 1/13

Windows 2003 ServerInstallation Guide

Revision 2.0

April 14, 2011



Licenses

This manual is the exclusive property of Prometric, Inc. This manual is licensed for use with restrictions to

authorized centers and Agents. Information herein is proprietary in nature and may not be disclosed tounauthorized persons without the expressed consent of Prometric.

Copyright©

2011 Prometric ALL RIGHTS RESERVED.

No part of this work covered by the copyright hereon may be reproduced or used in any form

or by any means—graphic, electronic, or mechanical, including photocopying, recording,taping, Web distribution, or information storage and retrieval systems, or in any other

manner—without the written permission of the publisher.



Windows 2003 Server Installation Guide 1

General ...................................................................................................................................... 1Minimum Testing Center Hardware/Software Specifications ................................................... 1

Network Requirements .............................................................................................................. 2

Additional Network Configurations .......................................................................................... 2IP Addresses and Ranges ........................................................................................................... 2

Host Names ............................................................................................................................... 3

Installation ................................................................................................................................. 4

Setting IP Configuration ............................................................................................................ 5

Install Window Updates ............................................................................................................ 5Configure Your Server as a Domain Controller ........................................................................ 6

Turning on the Firewall ............................................................................................................. 7

Setting Up a Printer ................................................................................................................... 7Antivirus Software ..................................................................................................................... 8

Pre-Configuration Check ........................................................................................................... 8

Adding Prometric URLs ............................................................................................................ 8



Prometric Revision 2.0 14-April -2011

Copyright 2011 Prometric. Information herein is proprietary and company confidential.

Windows 2003 Server Installation Guide - 1

Windows 2003 Server InstallationGuide

GeneralThis guide explains how to build a common network infrastructure beginning withthe installation and configuration of the Microsoft Windows Server 2003 operating

system as a domain controller.

Minimum Testing Center Hardware/SoftwareSpecifications

Table 1. APTC Windows Server Requirements. Components Requirement

Computer and

Processor

PC with a Pentium III, 1GHZ Processor

(To be exceeded if possible.)

Memory 512 MB of RAM required (1GB strongly advised for servicing more than 4-6 clientmachines.)

Hard disk 8 GB available hard disk space formatted for NTFS

(Intended as minimum free space available after OS + service pack installation.)

Drive CD-ROM (8X minimum) or DVD-ROM drive

Display Super VGA supporting 800 x 600 (or higher) resolution monitor

Network Ethernet 100 MB network interface card

Connectivity Internet connection

Other • Antivirus Software (updated)• MS compatible mouse• Internet Explorer 7 with all security updates installed.






Network Requirements

Table 2. Network Requirements. Details

In addition to the hardware requirements specified in Table 1, be aware of the following network requirements:

• Do not use Diamond video cards. They are packaged with a program titled Intel Net caster. This program is incompatible with our software.

• Except for your (optional) modem line, and/or Internet connection, there should be no way for any

out-of-network computer to communicate with the testing workstations.Note: Testing workstations need to have an Internet connection in order to fully comply with the Level 3requirements.

• The Windows 2003 server must have Service Pack 2.

• All the computers must be connected to the LAN.

• The drive letter F: should not exist prior to Prometric software installation. If F: does exist (because it is being used for a partition, device, etc.), assign a different, unused letter to that partition or device before beginning the APTC installation. During the installation, the drive F: will be automatically created.

• Hard drives must use the NTFS file system.

• The 2003 server must be set up as the primary Domain Controller of a separate Domain (do not set it upin a sub-Domain, trusted Domain, shadow Domain or stand-alone configuration).

• Log into the Windows 2003 Server as the administrator, not an equivalent.

• Make sure that TCP/IP is the only protocol used during the Network Setup.

Additional Network Configurations

Table 3. Additional Network Configurations. Details

Network and router configurations must be able to access: • Port 1555, 11001, 11002, 443, 80 bidirectional traffic• “Table 4. IP Addresses and Ranges.” contains complete list of network destinations and associated ports for

configuration by IP address• “Table 5. Host Names.” contains complete list of network destinations and associate ports by host name

Internet Explorer Trusted Sites:

• *.prometric.com• *.microsoft.com

(Wildcard* indicates that that all Prometric and Microsoft sites are trusted.)

Note: If you do not want to set Internet Explorer to trust all Prometric and Microsoft sites, add the individual

sites listed in “Table 5. Host Names.”

IP Addresses and Ranges

Table 4. IP Addresses and Ranges.

IP Address or Range Port

63.95.218.11 11001 and 11002

63.95.218.109 11001 and 11002






IP Address or Range Port

63.95.218.111 11001 and 11002

63.95.218.140 80

63.95.218.13 1555

63.95.218.86 80 and 443

63.95.218.87 80 and 443

63.95.218.112 80 and 443

207.46.18.235 443

207.46.18.182 443

207.46.18.229 443

207.46.18.* 443

65.55.11.* 443

65.55.10.* 443

Host NamesThe following host names need to be allowed through any network security measures

that restrict Internet access by host name.

Table 5. Host Names.

Host Name Port

*.pbt.microsoft.com 443

cert.learningservices.microsoft.com 443

ibt.prometric.com 80 and 443

ibt1.prometric.com 80 and 443

polaris.prometric.com 11001 and 11002

prod2-xmlfw.prometric.com 1555

pulse.prometric.com 11001 and 11002

utd.prometric.com 443

utdweb.prometric.com 80

ws.msllab.microsoft.com 443

ws3.msllab.microsoft.com 443

www.2test.com 11001 and 11002






Installation

Server Installation Basics

Table 6. Server Installation Basics. Details

• To begin the installation procedure, boot directly from the Windows Server 2003 SP2 CD.

• The set-up creates disk partitions on the computer running Windows Server 2003, formats the drive, andthen copies installation files from the CD to the server.• Prometric does not allow the use of Virtual Machine (VM) technology for test delivery.

Notes: • Your CD-ROM must support bootable CDs.• When you configure partitions and format drives, all data on the server hard drive is destroyed.

• These instructions assume that you are installing Windows Server 2003 on a computer that is not alreadyrunning Windows. Avoid upgrading from an existing Operating System by installing a fresh version ofWindows Server 2003.

Installation Procedures

Table 7. Installation Procedures. Step Details

1 Insert the Windows Server 2003 SP2 CD in the CD-ROM drive of the computer you will be using

as a server.

2 Restart the computer. If prompted, press any key to boot from the CD. The Windows Server 2003 installation begins.

3 On the Welcome to Setup screen, press Enter. The License Agreement screen appears.

4 Review and, if acceptable, agree to the agreement by pressing F8.

Note: If you had a previous version of Windows Server 2003 installed on the server, you might get

a message asking if you want to repair the drive. Press Esc to continue and do not repair the drive.

5 Follow the instructions to delete all existing disk partitions. The exact steps will differ based on the

number and type of partitions already on the computer. Continue to delete partitions until all diskspace is labeled as Unpartitioned Space.

6 After all disk space has been labeled as Unpartitioned Space, press C to create a partition in theUnpartitioned Space on the first disk drive (size as applicable, ex: 25000 MB).

7 Delete the total space default value. Type the value of your total disk space (in MB) at the Create

Partition of Size prompt. Press Enter.Note: The total disk space available is displayed when you format the drive. You determine howmuch you want to allocate to the new partition.

8 After the New <Raw> partition is created, press Enter.

9 Select Format the Partition using the NTFS file system <Quick>. Press Enter.

10 The Windows Server 2003 Setup formats the partition and then copies the files from the WindowsServer 2003 Server CD to the hard drive.

11 The server will restart.

12 The Windows Server 2003 Setup Wizard appears. It will detect and install devices.Note: This can take several minutes. During the process, your screen may flicker.

13 In the Regional and Language Options dialog box, be sure that your Regional Options are set toEnglish US and the short date format - MM/dd/yyyy. In addition, ensure that the Language for non-Unicode Programs on the Advanced Tab is set to English US. Click Next.






Step Details

14 In the Personalize Your Software dialog box, enter a name in the Name field and type in theOrganization’s name in the appropriate field. Click Next.

Note: The name should be short with no dashes or symbols. It can be any name.

15 Type the Product Key (located on the back of the Windows Server 2003 CD jewel case) in theappropriate field. Click Next.

16 In the Licensing Modes dialog box, select the appropriate licensing mode for your organization, and

then click Next. Select Per Seat.

17 In the Computer Name and Administrator Password dialog box, type the new computer name (toidentify that computer) in the computer name box, and then click Next.

Note: Windows Server 2003 requires “strong” or complex passwords.

18 Select Date and Time. The server will reboot.

Setting IP Configuration

Table 8. Setting IP Configuration Procedures.

Step Details

1 Go to Control Panel, Local Area Connection.

2 Click on Properties. Select Internet Protocol (TCP/IP). Then click Properties

3 Select Use the following IP address, and then type in your IP address. Enter the Default gateway,the Preferred DNS server and the Alternate DNS server addresses. Click OK, Close tocontinue.

Note: Windows 2003 Server does not accept dynamic IPs if set up as Domain Controller,

therefore, the fixed IP should be used. If in doubt, contact your company’s Network Administrator.

4 Restart and log in as Administrator.

Install Window UpdatesTable 9. Installing Windows Updates Procedures.

Step Details

1 When the Manage your server window appears, close it.

2 After the Windows 2003 Server is installed. Logon as Administrator. Go to Internet Explorer,Tools, Windows Update.

3 Click Update Windows. Update to latest Windows 2003 Service Packs.

4 Select Custom.

5

Select All Updates.6 Restart when all updates are complete.






Configure Your Server as a Domain Control ler

Table 10. Configuring Your Server as a Domain Controller Procedures.

Step Details

The IT server must be set up as a Domain Controller (not a member server). Domain Name Service (DNS) andDCPromo (the command-line tool that creates DNS and Active Directory) can be installed manually or byusing the Windows Server 2003 Manage Your Server Wizard. This section uses the manual tools tocomplete the installation.

Note: It is best to join the workstations to the Domain after installing all the required APTC testing software onthe 2003 Domain Controller

To install DNS and Active Directory using the manual tools:

1 Click Start, Run. Type DCPROMO, and then click OK.

2 When the Active Directory Installation Wizard appears, click Next to begin the installation.

3 Review the Operating System Compatibility information. Click Next.

4 Select Domain Controller for a New Domain (default), and then click Next.

5 Select Domain in a New Forest (default). Click Next.

6 For Full DNS Name, type the Domain Name (for example TestDom.com), and then click Next.(This represents a fully qualified name = includes a .com at the end of the name.)Note: The Domain name is created by the person setting up the network. It should be short with no

dashes or symbols. Examples: APTC or center number.

7 Click Next to accept the default Domain NetBIOS Name. (NetBIOS names provide for down-levelcompatibility.)

8 On the Database and Log Folders screen, point the Active Directory Log Folder to the suggesteddefault location, and then click Next to continue.

9 Leave the default folder location for Shared System Volume. Click Next.

10On the DNS Registration Diagnostics screen, click Install and configure the DNS server onthis computer. Click Next to continue.

11 Select Permissions Compatible only with Windows 2000 or Windows Server 2003 (default), andthen click Next.

12 Type the password for Restore Mode Password and Confirm Password. , and then click Next tocontinue.

Note: Always use complex passwords when creating Directory Services Restore passwords.






Step Details

13 The screenshot below shows a summary of the Active Directory Installation Options. Click Next to start the installation of Active Directory. If prompted, insert the Windows Server 2003

Installation CD. After the CD is inserted, a window comes up. Close it.

14 Click Finish once the Active Directory Installation is complete.

15 Click Restart Now to reboot the computer.

Turning on the Firewall

Table 11. Turning on the Firewall Procedures. Details

• Go to Start, Control Panel, Windows Firewall.

• Click Yes to turn on the firewall.

Setting Up a Printer

Table 12. Printer Set-up Procedures. Details

• Go to Start, Control Panel, Printers and Faxes, Add Printer.

Note: It is a contractual requirement that APTCs have a “dedicated” laser printer capable of at least 600 dpiand that only LPT and IP printers are supported. The printer must be set up as a network printer and shared onthe network.






Antivirus Software

Table 13. antivirus Software. Details

• Antivirus software should be installed on all APTC computers.• Avoid software such as McAfee with an “update agent” because the Agent will revert the regional options onthe computer to match the ones on the local distribution requirements. This will prevent most UTD examsfrom running on your workstations.

Pre-Configuration Check

Table 14. Pre-Configuration Check. Details

• Ensure that Server 2003 w/SP2 is set-up as a Domain Controller.

Adding Prometric URLs

Table 15. Adding Prometric URLs Procedures.

Step Details

1 From the Control Panel, select Internet Options. Click the Security tab. Highlight the Trusted

Sites icon. Click on Sites.





Step Details

2 Add these URLs by typing them into the Add this Web Site to the Zone in the Trusted Sites dialog box:

• https://www.prometric.com

• http://www.prometric.com

• https://www.2test.com

• http://www.2test.com

windows2003serverinstallationguiderev2.0 (1)

Documents