wickes kitchen self fit customer care guide

8/18/2019 Wickes Kitchen Self Fit Customer Care Guide

1/52

Kitchen RangeCustomer Care Guide

Receiving and Installing your New Kitchen


2/52

Important Information

Contents

Section 1: Your Guide to Components Received.

Section 2: Fittings Guide.

Section 3: Handy Hints on Preparation and Installation.

Section 4: Installation Sequence.

Section 5: Finishing Touches - Decor Panel Fitting.

Section 6: Finishing Touches - Door/Drawer Installation and Handle Fitting.

Section 7: Finishing Touches - Drawer Drilling and Other Internals.

Section 8: Finishing Touches - Curved Units.

Section 9: Finishing Touches - Other Decor Units

Section 10: Customer Care Guidance.

Section 11: Key Unit Dimensions.

Before you install your new Wickes Kitchen, please read this guide to receiving.

These guidelines are not a substitute for professional advice. Whilst every care has been taken to ensure that theproduct design, descriptions, specification and techniques of constructing the products are accurate at the date ofprinting, Products will inevitably change from time to time and the customer is advised to check the design, descrip-tions, specification and techniques of any of the products described in this booklet are still valid at the time of purchaseor placing an order. Where these guidelines vary from the instructions on a product or its packaging, then the instruc-tions on the product or the packaging should be followed.

Note: It is not advisable to fit a kitchen in a newly constructed or recently plastered room. A high moisture content inthe environment may cause the doors to swell and split. It is recommended that doors are stored outside the kitchenuntil the room has dried out thoroughly. A garage or other out buildings are not suitable for this purpose.

Should you require any additional support with regards to your project, please contact your nearest branch or our customer services department.

2


3/52

Section 1: Your Guide to Components ReceivedWickes Kitchens are supplied in a multi-pack format. Use this section as a checklist as it shows the componentbreakdown that makes up each ordered item. The drawing and description on the left is how the item was ordered. On theright is how the components will be shipped.Certain items, pelmet, cornice, plinth, end panels and worktops are supplied oversized to allow clean cutting to size. Handlesare supplied separately. Standard hinges are included with each unit, framed kitchens will receive a separate pack with thehinges and frame fixing components. Ensure all components are checked against delivery notes on receipt.Certain specific fittings and fixings may need to be purchased separately depending on such things as wall type or individualinstallations requirements.The below codes will be printed on the labels, “xx” is used to refer to code parts that will vary by kitchen range.

Base Units Carcase

Highline

300 Highline Base

400 Highline Base

500 Highline Base

600 Highline Base

800 Highline Base

1000 Highline Base

800 Highline Corner Base

1000 Highline Corner Base

Fascia

Ordered Item: Component Received:

(F3) 300 Highline Fascia


(F5) 500 Highline Fascia(NORLB5)500 Base/Sink Cabinet

(NORLB4400 Base Cabinet

(NORLB3)300 Base Cabinet

(NORLB10)1000 Base/Sink/Hob Cabinet


(YORLB6)600 Base/Sink/Hob Cabinet



450 Highline Base (F45) 450 Highline Fascia(NORLB45)450 Base/Sink Cabinet




2 x (F4) 400 Highline Fascia






(Requiredfascia sizedepends onunitconfiguration)


Additional Items

1 x Base Corner Filler


Base Units CarcaseDrawerline

300 Drawerline Base

400 Drawerline Base

500 Drawerline Base

600 Drawerline Base

1000 Drawerline Corner Base

800 Drawerline Corner Base

800 Drawerline Sink/Hob

500 Drawerline Sink



Fascia Additional Items

(FB3) 300 Drawerline Fascia




(NORLB5)500 Base/Sink Cabinet






(YORLB6)600 Base/Sink/Hob Cabinet








2 x (FB4) 400 Drawerline Fascia








1 x 780295 300 Single Drawer Set (Standard)1 x 780299 300 Single Drawer Set (Framed)



800 Drawerline Base

1000 Drawerline Base


2 x (FB5) 500 Drawerline Fascia(NORLB10)1000 Base/Sink/Hob Cabinet


1 xBaseCornerFiller

1 xBaseCornerFiller




1 x 780295 300 Single Drawer Set (Standard)

1 x 780299 300 Single Drawer Set (Framed)1 x 780296 400 Single Drawer Set (Standard)1 x 780300 400 Single Drawer Set (Framed)1 x 780297 500 Single Drawer Set (Standard)1 x 780301 500 Single Drawer Set (Framed)1 x 780296 400 Single Drawer Set (Standard)1 x 780300 400 Single Drawer Set (Framed)1 x 780297 500 Single Drawer Set (Standard)1 x 780301 500 Single Drawer Set (Framed)1 x 780298 600 Single Drawer Set (Standard)1 x 780302 600 Single Drawer Set (Framed)

Note: This unit does not have the drawer.


Drawer type depends on fascia style

3


4/52

4

Base Units

'L' Shape Corner Base

Highline 'L' ShapeCorner Base

Ordered Item: Component Received:FasciaCarcase

2 x (F3) 300 Highline Fascia925 Corner Base Cabinet(NORLCB9/1)Pack 1-Ends & Back(NORLCB9/2) Pack 2-Shelf Pack

1 x ¾ Carousel2 x (F3) 300 Highline Fascia




1 x Base Corner Filler 1 x ¾ Carousel



Base Units Carcase

Drawer Pack and Pan Drawers

300 Drawer Pack

600 3-Pan Prawer

900 3-Pan Drawer

Fascia

(FD34) 300 Drawer Pack Fascia

(FPD63) 600 3-Pan Drawer Fascia


500 Drawer Pack (FD54) 500 Drawer Pack Fascia

(FPD92) 900 2-Pan Drawer Fascia900 2-Pan Drawer

600 2-Pan Prawer

900 2-Pan Drawer withSink Drawer



(NORLD3)300 Drawer Cabinet

Additional Items

1 x 780303 300 Drawer set (Standard)1 x 780307 500 Drawer set (Standard) OR1 x 780311 500 Drawer set (Framed) and 1 x 780390 Packers

925 Corner Base Cabinet(NORLCB9/1)Pack 1-Ends & Back(NORLCB9/2) Pack 2-Shelf Pack



Drawerline 'L' ShapeCorner Base

Highline 'L' ShapeCorner Basewith Carousel

Drawerline 'L' ShapeCorner Basewith Carousel

Additional Items

925 Corner Larder Cabinet

(NORLCL9/1) Pack 1-HorizontalPanels(NORLCL9/2) Pack 2-Back Panels(NORLCL9/3) Pack 3-End/BackPanels(NORLCL9/4) Pack 4-Shelves(NORLTLEP)Pack 5-Ends

Larder 'L' ShapeCorner Unit

2 x (FL3) 1319 x 296 DoorFascia


1 x Larder Corner Filler 1 x Base Corner Filler



1 x 780312 600 Drawer set (Standard) OR1 x 780313 600 Drawer set (Framed) and 1 x 780390 Packers

(NORLD6)600 Drawer Cabinet 2 x 780395 600 Single Pan Drawer set (Standard)


1 x 780315 900 Drawer set (Standard) OR1 x 780316 900 Drawer set (Framed) and 1 x 780390 Packers

(NORLD9)900 Drawer Cabinet 2 x 780396 900 Single Pan Drawer set (Standard)

(NORLD9)900 Drawer Cabinet 1 x 780321 900 Single Pan Drawer sink set (Standard)

1200 2-Pan Drawer 2 x (NORLD6)

600 Drawer Cabinet

(FPD122) 1200 2-Pan

Drawer Fascia2 x 780314 600 Pan Drawer set (Standard)


5/52

5

Ordered Item: Component Received:Wall Units FasciaCarcase Additional Items

300 Wall Unit (F3) 300 Highline Fascia


500 Wall Unit



600 x 441 Cooker HoodBridging Unit

600 x 294 Cooker HoodBridging Unit

625 L-ShapedCorner Wall Unit

(NORLW3) 300 Wall Cabinet




(NORLCW6L)625 x 735 Corner Wall Cabinet

(NORLCH64) 600 x 441 Wall Cabinet (FCH) 437 x 596 Door Fascia

800 Wall Unit 2 x (F4) 400 Highline Fascia

1000 Wall unit 2 x (F5) 500 Highline Fascia



(NORLCH63) 600 x 294 Wall Cabinet (FAH1) 290 x 596 door Fascia

(FCWL6)Pair of Doors 285mm Wide(includes filler)

600 Closed CornerWall Unit

(NORLW6)600 Wall Cabinet


450 Wall Unit (NORLW45) 450 Wall Cabinet

600 Wall Unit (2 Doors)


(NORLW6) 600 Wall CabinetNote: This unit will not have the mullion


500 Glass Wall Unit(LxxXODU5) 500 x 735 OpenDisplay Unit

(F5G) 500 Glass Fascia

500 Aluminium GlassWall Unit (LQQAGF5) 500 AluminiumGlass Fascia

600 MicrowaveWall Unit

1 x NORLMWC Corner WallConversion Kit

(IN110) 110 x 596 Filler Panel

(FAH1) 290 x 596 door Fascia1 x NORLBS6 Base Shelf 1 x Microwave

600 x 367 Mid HeightFeature Bridging Unit (NORLMHF6) 600 x 367 Wall Cabinet (FMH6) 596 x 363 Door Fascia

900 x 367 Mid HeightFeature Bridging Unit (NORLMHF9) 900 x 367 Wall Cabinet (FMH9) 896 x 363 Door Fascia

900 x 367 Mid HeightFeature Bridging Unitwith Aluminium Glass door

(AGFMH9) 363 x 896 AluminiumFeature Door Fascia

900 Full HeightFeature Aventos Unit

(NORLFHF6) 600 Full Height featureCabinet 2 x (FMH6) 363 x 596 Door Fascia


(NORLFHF9) 900 Full Height featureCabint 2 x (FMH9) 363 x 896 Door Fascia

Dresser Units Carcase Fascia Additional Items

500 Dresser Cabinetwith Glass Door

(LxxXDCT) 500 Dresser Cabinet (FDR) 500 Glass Dresser Fascia

(FDF5) 500 Drawer Fascia

1 x LQQGS3 3 Pack of Glass Shelves1 x 780322 500 Dresser CabinetDrawer (Standard) OR1 x 780323 50 Dresser CabinetDrawer (Framed)

f


(AGFMH6) 363 x 596 AluminiumFeature Door Fascia

600 x 367 Mid HeightFeature Bridging Unitwith Aluminium Glass door

(NORLMHF6) 600 x 367 Wall Cabinet

(NORLMHF9) 900 x 367 Wall Cabinet


2 x (NORLW6)600 Wall Cabinet 2 x (FMH12) 363 x 1196 Door Fascia

1 x LQQAMP12 AventosMechanism

500 Dresser Cabinetwith Tambour Door

(LxxXDCT) 500 Dresser Cabinet1 x KQQTM TambourFascia/Mechanism

1 x LQQHPCS107 Hinge Pack

600 Bifold Wall Unit

600 Lift up and over

Wall Unit





1 x LQQBFM6 Bifold Mechanism

1 x LQQLUO/1 Lift up andover Pack 1

1 x LQQLUO/2 Lift up andover Pack 2


6/52

6

Ordered Item: Component Received:Tall Wall Units FasciaCarcase Additional Items

300 Tall Wall Unit (FTW3) 300 Tall Wall Fascia


500 Tall Wall Unit

(FTW45) 450 Tall Wall Fascia


625 Tall L-ShapedCorner Wall Unit`

(NORLTW3) 300 Tall Wall Cabinet




800 Tall Wall Unit 2 x (FTW4) 400 Tall Wall Fascia

1000 Tall Wall unit 2 x (FTW5) 500 Tall Wall Fascia



(FTCWL6)Pair of Doors 285mm Wide(includes filler)

600 Tall Closed CornerWall Unit

(NORLTW6)600 Tall Wall Cabinet


450 Tall Wall Unit (NORLTW45) 450 Tall Wall Cabinet

600 Tall Wall Unit (2 Doors)


(NORLTW6) 600 Tall Wall CabinetNote: This unit will not have the mullion

2 x (FTW3) 300 Tall Wall Fascia

500 Tall GlassWall Unit

(LxxXTODU5) 500 x 735 Tall OpenDisplay Unit

(FTW5G) 500 Glass Fascia

600 x 448 Tall Mid HeightFeature Bridging Unit (NORLTMHF6) 600 x 448 Wall Cabinet (FTMH6) 596 x 444 Door Fascia

900 x 448 Tall Mid HeightFeature Bridging Unit (NORLMHF9) 900 x 448 Wall Cabinet (FTMH9) 896 x 444 Door Fascia

900 Tall Full HeightFeature Aventos Unit

(NORLTFHF6) 600 Tall Full Heightfeature Cabinet 2 x (FTMH6) 363 x 596 Door Fascia

600 Tall Full HeightFeature Aventos Unit

(NORLTFHF9) 900 Tall Full Heightfeature Cabinet 2 x (FTMH9) 363 x 896 Door Fascia

Display Units FasciaCarcase Additional Items

500 Open DisplayUnit (Base or Wall)

(LxxXODU5) 500 x 735 OpenDisplay Unit

500 Open DisplayUnit with Frame(Base or Wall)

500 Open DisplayUnit with Plate Rack 1 x KxxPRP Plate Rack

500 Open DisplayUnit with Plate Rackand Frame

(ODF5) Open Display Frame

500 Tall Open DisplayWall Unit

(LxxZTODU5) 500 x 896 TallOpen Display Unit

(LxxZTODU5) 500 x 896 TallOpen Display Unit

500 Tall Open DisplayWall Unit with Frame

(TODF5) Tall OpenDisplay Frame

f






500 Open DisplayUnit with Wine Rackand Frame

500 Open DisplayUnit with Wine Rack



1 x KxxPRP Plate Rack

1 x KxxWRP Wine Rack

1 x KxxWRP Wine Rack

1 x NORLTMWC Corner WallConversion Kit

1 x LQQHPCS107 Hinge Pack

625 x 896 Corner wall Cabinet(NORLTCW6/1)Pack 1-Ends & Back(NORLTCW6HL) Pack 2-Shelf Pack

1 x LQQAMPH AventosHeavy Duty Mechanism

(FDF5) 500 Drawer Fascia500 Base DisplayUnit with FeatureBaskets

(LxxXBDU5) 500 x 735 BaseDisplay Unit

1 x 780297 500 Single Drawer Set(Standard/Framed with Oak/SteelBaskets) OR1 x 780301 500 Single Drawer Set(Framed with Wicker Baskets))

2 x KQQWBP Wicker Basket Set OR2 x 212926 Oak/Steel Basket Set


7/52

7

Ordered Item: Component Received:150mm Units FasciaCarcase Additional Items

150 Pull Out Unit withWirework Baskets (PO15) 150 Pull Out Fascia

(NORLPO15) 150 Pull OutCabinet

150 Wine Rackwith Frame (WRF15) 150 Wine Rack Frame

150 Wine Rack (LxxXWR) 150 Wine Rack Cabinet

(LxxXWR) 150 Wine Rack Cabinet

150 Tall Wine Rack

150 Tall Wine Rackwith Frame

(LxxXTWR) 150 Tall WineRack Cabinet

(LxxXTWR) 150 Tall WineRack Cabinet

(TWRF15) 150 Tall WineRack Frame

1 x 192508 Wirework (Mesh) OR1 x 106372 Wirework (Solid)

150 Pull Out Unit withTray

(NORLPO15) 150 Pull OutCabinet (TUF) Tray Unit Frame 1 x LWOST Tray

Other Base Units FasciaCarcase Additional Items

600 Under OvenHousing Unit (FBU6) 131 x 596 Fascia

(YORLBU6) 600 Built-under Oven Cabinet

600 Butler Sink unitfor 28mm Thick Worktops

(YORLBUTS6) 600 Butler SinkSupport Cabinet

(NORLBSSU6) 600 Belfast SinkSupport Cabinet


(FCH) 437 x 596 Door Fascia

600 Butler Sink unitfor 38mm Thick Worktops

(FBU6) 131 x 596 Fascia


600 Belfast Sink Unitwith Door

1 x Single Oven

600 Under OvenHousing Unit with Drawer

(YORLBU6) 600 Built-under Oven Cabinet (FBU6) 131 x 596 Fascia

1 x Single Oven1 x 780298 (Tandem) 600Single Drawer Set

(YORLBUTS6) 600 Butler SinkSupport Cabinet




2 x (FBS45) 437 x 435 Door Fascia

900 Belfast Sink Unitwith Doors

(NORLBSSU9) 900 Belfast SinkSupport Cabinet

600 Butler Sink unitfor Bow Front Sinks

(YORLBUTS6) 600 Butler SinkSupport Cabinet (to be cut down)



1 x Roll of Edging Tape


600 Base with Pullout Accessories (F6) 600 Highline Fascia

1 x 780360 Pull out Shallow Drawer 2 x 780348 Pull our Deep Drawer OR1 x 106393 Wine Rack runners2 x 106394 Wine Rack mesh basketOR1 x 106393 Wine Rack runners2 x 106395 Wine Rack Solid backet


8/52

8

Curved Units FasciaCarcase Additional Items

925 Internal CurvedCorner Wall Unit

(NORLCW6C) 625 Internal CurveCorner wall Cabinet

2 x (YORLW3) 300 Wall Cabinet

(FCCW6) 625 Curved Corner BaseFascia set

925 Internal CurvedCorner Base Unit

(FCCB9) 925 Curved Corner BaseFascia set (2 Doors)

925 Internal Curve CornerBase Cabinet(NORLCB9/1 )Pack 1-Ends & Back(NORLCCB9/2) Pack 2-Shelf Pack

300 External CurvedWall Unit

(NORLBWCU) 300 ExternalBase/Wall Cabinet1 Pair of 90° degree hingesincluded

(FCBW) External Curved Door NOTE: Certain ranges have leftand right hand variants

300 External CurvedBase Unit with Wine Racks


2 x (LxxXWR) 150 Wine Rack Cabinet


300 External CurvedBase Unit with 300 WallUnit





300 External CurvedLarder Unit

300 External CurvedLarder Cabinet -Flatpack(NORLTCU/1 )Pack 1-Ends(NORLTCU/2) Pack 2-Shelf Pack5 Curved Larder hinges included


(FL3CL) External Curved Larder Door NOTE: Certain ranges have leftand right hand variants

1 x FTBP Tall Blanking Panel


1 x KQQ17HCS Hinge pack

1 x KQQ17HCS Hinge pack


9/52

9

Ordered Item: Component Received:Standard Height Larder Storage Units FasciaCarcase Additional Items

300 Larder Unit

300 Larder Unit withPull Out Softclose Basket

500 Larder Unit

500 Larder Unit withSwing Softclose Basket

600 Larder Unit

300 Larder Cabinet(NORLTLEP)Pack 1-Ends(NORLHP3) Pack 2-Horizonals/BackPanels



500 Larder Cabinet

(NORLTLEP)Pack 1-Ends(NORLHP5) Pack 2-Horizonals/BackPanels

600 Larder Cabinet(NORLTLEP)Pack 1-Ends(NORLHP6/1) Pack 2-Back Panels(NORLHP6/2) Pack 3-Horizontal Panels

(FL3) 1319 x 296 Door Fascia










3 x LQQHPCS107 Hinge Pack3 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)

10 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)1 x Pull out Frame1 x Pull out Runner 1 x 300 Pull out Basket Set

3 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)

1 x LQQHPCS107 Hinge Pack3 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)

10 x LQQCCx 35mmCover Cap (Colour

co-ordinated to door)1 x VSA Frame1 x VSA Runner 1 x 500 VSA Basket Set




400 Larder Unit


2 x (FL5) 1319 x 496 Door Fascia


1000 Larder Unit

1000 Larder Cabinet(NORLLP10/1)Pack 1-Ends(NORLLP10/2) Pack 2-Horizontal Panels(NORLLP10/3) Pack 3-Horizontal Panels(NORLLP10/4) Pack 4-Back Panels

Corner Pantry Larder Unit

Corner Pantry Larder Unit(NOxxCLU/1) Pack 1(NOxxCLU/2) Pack 2(NOxxCLU/3) Pack 3(NOxxCLU/4) Pack 4(NOxxCLU/5) Pack 5(NOxxCLU/6) Pack 6(NOxxCLU/7) Pack 7

2 x (FL4) 1319 x 396 Door Fascia


1 x Corner PantryLarder unit Plinth kit2 x Colour Specific TallEnd panels


10/52

10

Additional ItemsMid Height Larder and Appliance Units

600 Mid Height Unit

Type A - Larder


FasciaCarcase


600 Mid Height UnitType B - Fridgeor Freezer

600 Mid Height UnitType C - CompactOven with Door

600 Mid Height UnitType D - CompactOven with Drawers

600 Mid Height UnitType E - SingleOven with Door

600 Mid Height UnitType F - SingleOven with Drawers

(FAH1) 296 x 596 Door Fascia



(FA6) 600 Highline Fascia






(FPD6) 600 3-Pan Drawer FasciaNOTE: Only larger fascias required

1 x Larder Fridge ORFreezer

1 x Compact Oven

1 x Compact Oven1 x 780312 600 Drawerset (Standard)

1 x Single Oven

1 x Single Oven1 x 780314 600 Pan Drawerset (Standard)

Tall Height Larder Storage Units FasciaCarcase Additional Items

300 Tall Larder Unit

300 Tall Larder Unit withPull Out Softclose Basket

500 Tall Larder Unit withSwing Softclose Basket


300 Tall Larder Cabinet(NORLTTLEP)Pack 1-Ends(NORLTHP3) Pack 2-Horizonals/BackPanels


500 Tall Larder Cabinet

(NORLTTLEP)Pack 1-Ends(NORLTHP5) Pack 2-Horizonals/BackPanels

600 Tall Larder Cabinet(NORLTTLEP)Pack 1-Ends(NORLTHP6/1) Pack 2-Tall Back Panels(NORLHP6/2) Pack 3-Horizontal Panels

(FTL3) 1466 x 296 Door Fascia








3 x LQQHPCS 107 Hinge Pack3 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)

10 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)1 x Pull out Frame1 x Pull out Runner 1 x 300 Pull out Basket Set







5 x LQQCCx 35mmCover Cap (Colourco-ordinated to door)1 x VSA Frame1 x VSA Runner 1 x 500 VSA Basket Set






600 Mid Height Cabinet(NORLTTLEP)Pack 1-Ends

(NORLTHP6/1) Pack 2-Tall Back Panels(NORLHP6/2) Pack 3-Horizontal Panels

600 Mid Height Cabinet(NORLTTLEP)Pack 1-Ends(NORLTHP6/1) Pack 2-Tall Back Panels(NORLHP6/2) Pack 3-Horizontal Panels






11/52

11

Ordered Item: Component Received:Standard Height Appliance Units FasciaCarcase Additional Items

600 Appliance HousingUnit A - Single Ovenwith Door

1 x Single Oven

600 Appliance HousingUnit B - Double Ovenwith Door

600 Appliance HousingUnit C - Microwaveand Oven

600 Appliance HousingUnit D - Two Single Ovens

600 Appliance HousingUnit E - Fridge/Freezer

600 Appliance HousingUnit F - Fridge Freezer

600 Appliance HousingUnit G - Fridge Freezer

600 Appliance HousingUnit H - Single Ovenwith Drawers

600 Appliance HousingUnit J - Double Ovenwith Drawers

600 Appliance HousingUnit K - Microwaveand Oven with Drawers

600 Appliance HousingUnit L - Compact Ovenand Microwave

600 Appliance HousingUnit M - Double Ovenand Microwave

600 Appliance Cabinet -Flatpack(NORLTAE6 )Pack 1-Ends(NORLHP6/1) Pack 2-Back Panels(NORLHP6/2) Pack 3-Horizontal Panels


































(FPD6) 600 3-Pan Drawer FasciaNOTE: Only top and bottom fasciasrequired

1 x Double Oven

1 x Microwave (Upper Aperture)1 x Single Oven (Lower

Aperture)

2 x Single Oven

1 x LQQHPCS107 Hinge Pack1 x Larder FridgeOR Freezer

1 x Larder Fridge and1 x FreezerOR 1 x Fridge/Freezer

1 x LQQHPCS107 Hinge Pack1 x Fridge/Freezer

1 x Single Oven1 x 780314 600 Pan Drawerset (Standard)

1 x Double Oven1 x 780314 600 Pan Drawerset (Standard)


Aperture)1 x 780312 600 Drawerset (Standard)

1 x Microwave (Upper Aperture)1 x Double Oven (Lower

Aperture)

1 x Microwave (Upper Aperture)1 x Compact Oven (Lower

Aperture)




600 Appliance Cabinet -Flatpack

(NORLTAE6 )Pack 1-Ends(NORLHP6/1) Pack 2-Back Panels(NORLHP6/2) Pack 3-Horizontal Panels









12/52

12

Ordered Item: Component Received:Tall Height Appliance Units FasciaCarcase Additional Items

600 Tall ApplianceHousing Unit A - SingleOven with Door

1 x Single Oven

600 Tall ApplianceHousing Unit B - Double

Oven with Door

600 Tall ApplianceHousing Unit C -Microwave and Oven

600 Tall ApplianceHousing Unit D - TwoSingle Ovens

600 Tall ApplianceHousing Unit E -Fridge/Freezer

600 Tall ApplianceHousing Unit F -Fridge Freezer

600 Tall ApplianceHousing Unit G -Fridge Freezer

600 Tall ApplianceHousing Unit H - SingleOven with Drawers

600 Tall ApplianceHousing Unit J - DoubleOven with Drawers

600 Tal ApplianceHousing Unit K -Microwave and Ovenwith Drawers

600 Tall ApplianceHousing Unit L -Compact Oven andMicrowave

600 Tall Appliance Cabinet -Flatpack(NORLTTAE6 )Pack 1-Ends(NORLTHP6/1) Pack 2-Back Panels(NORLHP6/2) Pack 3-Horizontal Panels

1 x Double Oven


Aperture)

2 x Single Oven

1 x LQQHPCS107 Hinge Pack1 x Larder FridgeOR Freezer

1 x Larder Fridge and1 x FreezerOR 1 x Fridge/Freezer

1 x LQQHPCS107 Hinge Pack1 x Fridge/Freezer

1 x Single Oven2 x 780395 600 Single Pan Drawerset (Standard)

1 x Double Oven1 x 780312 600 Drawerset (Standard)


Aperture)1 x 780312 600 Drawerset (Standard)

1 x Microwave (Upper Aperture)1 x Compact Oven (Lower

Aperture)
























NOTE: Only larger fascias required

(IN110) 110 x 596 Filler

(FPD6) 600 3-Pan Drawer FasciaNOTE: Only top and bottom fasciasrequired


(IN110) 110 x 596 Filler








600 Tall Appliance Cabinet -Flatpack

(NORLTTAE6 )Pack 1-Ends(NORLTHP6/1) Pack 2-Back Panels(NORLHP6/2) Pack 3-Horizontal Panels









13/52

13

Accessories:Standard MFC Plant on Panels

(EWS) Decor Base Panel890 x 600

(MDPW18) Decor Wall Panel795 x 337

(MDPTW18) Decor TallWall Panel 956 x 337

(MDPD18) Decor Dresser Panel 1283 x 337

(MDPT18) Standard andTall Appliance/LarderPanel 2400 x 600

(BB) Breakfast Bar Back Panel2400 x 890

Premium Panels

(TDPB18) Decor Base Panel890 x 600

(TDPW18) Decor Wall Panel795 x 337

(TDPTW18) Decor TallWall Panel 956 x 337

(TDPD18) Decor Dresser Panel 1283x 337

(TDPT18) Standard andTall Appliance/LarderPanel 2400 x 600

(CP) 2.6m Continuous Plinth

(CPV) 2.6m Veneered orPVC Continuous Plinth

Other Accessories

(CBP) External CurvedPlinth

(CCBP) Internal CurvedPlinth

(MOD) 2.6m Modern Cornice,Pelment and Classic Pelmet

(MTC) 2.6m Classic Cornice

(CBTQx) External CurveClassic CorniceNOTE: Item is handed

(CCWCx) Internal CurveModern Cornice andPelmet Block

(TP) Tall Pilister

(CBDQ) External CurveModern Cornice andPelmet BlockNOTE: Style will vary byrange

(ET) 10mm Roll ofEdging Tape

(BCFx) Base Corner Filler

(TCP) Tall CurvedCorner Post

(BB) Breakfast Bar Back Panel2400 x 890

(FDPB18) Framed DecorBase Panel

(FDPW18) Framed DecorWall Panel

(FDPTW18) Framed DecorTall Wall Panel

(FDPD18) Framed DecorDresser Panel

(FDPT18) Framed DecorStandard Tower Panel

(FDPTT18) Framed DecorTall Tower Panel

(CBTDx) External CurveClassic CorniceNOTE: Item is handed


14/52


15/52

15

Section 3: Handy Hints onPreparation and Installation

Please spend five minutes reading this section beforecommencing to assemble and install a Wickes Kitchen

CAUTION!

Some pieces of hardware could be hazardous to small children.

Keep all these items out of reach and do not leave children unattended in theassembly area.

Many of the units, particularly the double door units and tall units, are heavy andshould be lifted with caution.

To reduce risk, do not fit doors or drawers until the units have been attached to thewalls.

DO NOT USE A KNIFE TO OPEN THE BOXES AS THIS MAY DAMAGE THE CONTENTS.

Read the Plans

Preparation

Services

•Find and review the plans and any other drawings used to prepare your order. Pay particular attentionto any units that have special features or will be positioned unusually.

Before starting any assembly, spend some time preparing the area where the units will be fitted.To help your project run smoothly, make sure you've checked the measurements and dimensionsbefore you start work.

After checking that all the units ordered have been delivered, the area should be stripped out and anyobstructions such as old skirting, disused pipes, tiles etc. removed.It is not advisable to fit timber doors in newly constructed or recently plastered rooms. High moisturecontent in the environment may cause the doors to swell and split.Don't store the products in an unsuitable place or on hard surfaces such as concrete etc. as they mayget damaged.To get long term use and performance from Wickes products, make sure the kitchen is installedas per these guidelines.Protect the finish on panels by laying them on the floor and using the packaging to prevent scratches.Do not over tighten screws and be particularly careful when using power screwdrivers.

Make sure that all the parts and hardware have been enclosed. Contact our Customer Servicesdepartment if there is anything missing or damaged. All are supplied flatpack to ensure they reach you in the best possible condition. It is recommendedthat the larger units are built in the room they are to be installed as it may not be possible to movethem into the room once they have been assembled.

••

•

•

•

•

••

•

•

If you wish to fit or move any electric, gas or water points, now is the time to do this. If in doubt orunsure, seek advice from a qualified profressional.Services to appliances should be to the manufacturer's specification and fitted by a qualified person.If unsure of any part of your design or layout, then please contact your Design Consultant at your localstore.

•

••


16/52

16

Walls and Floor

Decorating

Tools

Make sure all plaster work is sound particularly where the units will be attached. This is between 800and 870mm up the wall for base units and between 2100 and 2400mm from the floor for wall units. Itis important to make sure all plaster is dry before fitting units as damage may occur to the units.Floors should be sound and able to take the weight of the units and appliances.

•

•

Although the units will cover a large amount of the floors and walls, it may well be easier to decoratethe areas of the walls, ceiling and floor that will show around the units before installation. This isparticularly true of the wall and ceiling above the wall units and space between the base and wallunits. If tiles are to be fitted, it is recommended that this is done after the units and worktop havebeen installed.

•

The following tools are necessary for assembling and installing the units:•

Cross head No2 Screwdriver

5mm Flat Screwdriver

Metric Tape Measure

Spirit Level

Electric Drill with 15mm, 8mm, 5mmand 3mm diameter wood drillbitsand appropriate masonry drillbits

Bradawl

Mallet/Hammer

G-Clamps (minimum of two)

Mitre Block

15mm

8mm

5mm

3mm

Set Square(s)

Dustmask (to be wornwhenever cutting MDF)

Along with the above, you will also require a panel saw, jig saw and mitre saw. Always use a workbench or a firm work surface.

•


17/52

17

Step 1 - Get Ready

Section 4: Installation Sequence

Read the Handy hints pages.Check the plans for thekitchen.

Try assembling a smallunit to familiarise yourselfwith the procedure.

Corner Base unitDrilling advice.In order to allow for thenumberous configura-tions this unit requiresdrilling at locations A, Band C as shownopposite. The holes arepart drilled for ease ofuse. Use a 5mm drill,and drill into a piece ofscrap wood.NOTE: Location C onlyneeds drilling unit is tobe drawerline.

5mm

A

B

C

Step 2 - Start in a Corner

Begin in a corner. If a Cornerunit is to be fitted, assembleand position this unit in thecorner.If the units are to be fittedbetween two corners, refer tothe plan to see which is the

starting point.The units illustrated on thefollowing two pages are allcommonly used to start a runof units in a corner.If the kitchen does not fit up toa corner, remember to allow forcurve units or show ends whenpositioning the first unit.

Standard Base UnitThis will begin a straightrun of units.

Appliance Housingor Larder unitThis will begin a straightrun of units.

Unit Size (mm) Required Door Size (mm) Total Length in Plan (mm) Void "x" (mm)

800mm 300 925 125

800mm 400 1025 225

800mm 500 1125 325

1000mm 400 1025 25

1000mm 500 1125 125

1000mm 600 1225 225

Corner Base UnitFollow installationinstructions below forthe correct position inthe corner.

When installing a Corner base Unit, be careful on the position of the unit and be sure to check your plan. There are a wide variety of both the800mm and 1000mm options. Each has a different size door, so demands a different amount of wall space, which in turns means the void (x) onthe above image is different. Please use the table below as a guide to fitting this unit in the correct space. The plan will also detail the require-ments. See below for drilling advice.

U n i t S i

z e

6 2 5 m m

T o t a l L e

n g t h o

n P l a n

X

55mm

5 2 m m

15mm

U n i

t S i z e

X

625mm

T o t a l

L e n g

t h o n

P l a n

D o or

S i z

e

If your kitchen consists of straight runs only(no corner units), then it is advisable to useeither of the following as the first unit.


18/52

18

Bottom PanelDrilling

Carousel

15mm

7mm

CarouselTop Panel

Drilling

15mm

8 0 m m

8 0 m m 8 0 m

m

8 0 m m

925 x 925 Corner LarderUnitThe shelf or carousel inthe bottom part of theunit MUST be fittedbefore installation.To fit the carousel, it isnecessary to drill a15mm diameter hole inthe top and bottom panelin the locations shown inthe illustration.

9 2 5 m m

925mm

925 L-ShapedCorner Larder

Corner Larder PantryUnitThis unit MUST be fittedwith decorative ends toensure door hinges donot clash with adjacentworktops. Allow for thesewhen fitting.Note: Decorative endsshould be planned inwith yourkitchen.Contact customerservices if either aremissing.

Decorative ends

1 1 7 2 m m

1172mm

Corner LarderPantry Unit

Note: Measurement of1172mm includes thedecorative end panels.

Bottom PanelDrilling

Carousel

15mm

7mm

CarouselTop Panel

Drilling

15mm

8 0 m m 8 0 m m

8 0 m m 8 0 m m

925 x 925 Corner Unitand Internal CornerBase unitThe shelf or carouselMUST be fitted before

installation.To fit the carousel, it isnecessary to drill a15mm diameter hole inthe top and bottom panelin the locations shown inthe illustration.

9 2 5 m m

925mm

925 L-Shaped

Corner Base

9 2 5 m m

925mm

925 Curved

Corner Base


19/52

19

Step 3 - Tall Units Step 4 - Assemble and Position the Base Units

Assemble the appliance/larderunits and place in position asshown on the plan.

Assemble any remaining baseunits and place in position.

Sink units should be cut asnecessary for the plumbing.Find the lowest point on thefloor. The legs on the unit inthis position should be 140mmhigh plus the thickness of anyflooring that will be underneaththe plinth. Level the remainingbase units, working away fromthis unit.

1 4 0 m m

P l i n t h

F l o o r

C o v e r i n g

Floor Spirit Level

Step 5 - Connect the Base Units and fix to the Wall

Once the units are correctly

positioned, start in a cornerand fix the units to the wall andconnect them together.Fix to the wall with the suppliedbrackets. Use plugs or othersuitable fixings of the correcttype for the wall constructions.Tall and appliance units inparticular must be securelyfixed.

G-clampsDrill

PlasterboardFixings - Notsuitable formany units.See notesopposite.

Please use suitable fixings(not supplied)

The connecting bolts used toconnect the units together canbe hidden by putting themadjacent to the hinge plate,shelf or drawer runner.

Clamp the units together. Decide where to locate the connection bolts. Thisshows the hole being drilled behind a hinge location. Drill through with a 5mmwood drill into a piece of scrap wood. Push in the bolt and tighten the screw.

Alternative positionabove a drawer runner.

Mark the position for drilling. Remove a screw from the bracket and move the bracket out of the way. Drill

using a bit suitable for the wall and the size of wall plug. Fit the plug. Put the bracket back in position,replace the screw and fit a suitable screw into the wall. Plasterboard is not strong enough to support wall ortall units so plasterboard fixings are not sutiable for fixing those units but are acceptable for base units only.Tall units, especially ones with appliances, need to be very securely fixed to the wall. If necessary fit abatten to studs within the wall and then fix the unit to the batten.

5mm


20/52

20

Step 6 - Mark a line for the wall hanging plates

Mark a line around the room at the height for the wallhanging plates.

Kitchens WITH tall or standard larder/appliance housingunits: measure 64mm down from the top of the larder/appli-ance housing unit.

Kitchens WITHOUT tall or standard larder/appliancehousing units but WITH standard wall units: measure2134mm up from the floor.

Kitchens WITHOUT tall or standard larder/appliancehousing units but WITH tall wall units: measure 2281mm upfrom the floor.

If there are dresser units, make sure there is 1259mmbetween the line and the top of the base units. See page 39for further information.

Dresser Position

2 1 3 4 m m

1 2 5 9 m m

6 4 m m

C e n t r e l

i n e S c r

e w S l o

t s C e n t r e l i n e S c r e w S l o t s

Step 7 - Assemble and fit the Corner Wall Units

PlasterboardFixing - Notsuitable for wallunits.See notes in step 4.

2 people are

required for thisstage

CAUTION!

600 Closed CornerWall Unit

L - Shaped Corner Wall

Assemble the corner wal l unit. Thereare a number of types of corner unit.

Installation for the L-Shaped andinternal curved cabinet are as follows:Fix the wall hanging plates to the wallas shown in the instructions. Theyare fitted to the wall 20mm in from theoutside edge of the unit. Use plugs orother suitable fixings of the correcttype for the wall construction.

Installation for the 600 closed cornerwall unit with blanking panel is asfollows:This must be fitted to the wall whilstleaving a 25mm gap between the unitside panel and the wall.

Wall hanging plates must be securelyfixed to the wall. if necessary, fit abatten to studs within the wall andthen fix the plates to the batten. Seekadditional assitance if required.Hang the unit on the plates. Thisrequires two people. Don’t adjust thehanging bracket at this stage.

625 Internal CurvedCorner Wall Unit

Dresser Position

C e n t r e l i n e

S c r e w

S l o t s C e n t r e l i n e S c

r e w S l o t s

2 0 m m 2 0 m m

6 4 m m

2 0 m m

1

6 4 m m

2 0 m m

2

2 0 m m

4

2 0 m m

3


21/52

21

Step 8 - Assemble and fit the remaining wall and feature units

Assemble the remaining wallunits and accessories. Hangthe remaining wall units.Level the wall units byadjusting the wall hangingbrackets and fit the covers.Fix the standard unitstogether with connectingbolts (see Step 4).Certain Accessories areconnected with 30mm screwsfitted from the adjacent unitsinstead of connecting bolts.Fit wine rack frames before

fixing to other units. After fix ing, tighten the unitsto the wall. Fitting Accessories

Use 30mm screws to connect the accessories toother units. Countersinking the screws allows themto be fitted behind hinge plates, shelves or drawerrunners.Use a 3mm drill to make 30mm deep pilot holes.Do not drill through both units.

G-clampsDrill

3mm4x30mm

Step 9 - Fit decor ends and Laminate Worktops

If décor panels have beenordered, fit them now. Seepage 23 for details.Cut the worktop to the correctsize and apply edging.Mark and cut out the holesfor the sinks and hobs.Fit the worktops. For laminateworktops, see opposite, forother worktop types, pleasesee instructions from thesupplier. At the front, theworktop is held in place byscrews through the front rails.

At the rear, use roundheadscrews through the brackets.

Fit the hob. Refer to themanufacturers handbook.Fit the sink. Finish plumbing.

WorktopsCutting - Before cutting be sure to double-checkall measurements.If using an electric circular or jig saw, cut theworktop face down so that the saw teeth cut intothe laminate surface starting from the profiledfront edge.If using a hand saw, (10 to 12 teeth per 25mm)cut the worktop face up. Always start from theprofiled front edge and keep the saw at a lowangle.Once cut, the worktop can be trimmed and

cleaned using a portable hand router to acheivea perfect chip free cut.

Joints - Ensure the two edges are clean andapply a continious bead of sealant down entirelength of join. Use three tension bolts to tightenuntil joint is tight and allows excess sealant toform over join then wipe off all excess.

Sealing - All cut edges where raw chipboard isexposed on both the worktop and the carcasemust be sealed with a moisture resistant sealersuch as gloss paint, varnish or silicone sealant.

Cut-Outs - Any cut-outs should be carefullymeasured and marked. Work from the decorativeface, drill through corners with a 12mm drill bit toallow access for jig saw. It is recommended toleave at least 250mm between cut-outs and fromcut-outs to edge of worktop. Leave a 50mm gapbetween cut-outs and the front and back edges.

Always follow instructions on sealant labels.

Overhang

4x30mm4x15mm


22/52

22

Step 10 - Fit Dressers, Cornice, Pelmet and Appliances

Fit the dressers, see page 45for further information.Tile the walls and finishdecorating.Mitre and fit the cornice andlight pelmet.Fit remaining appliances,refer to manufacturersinstructions for information.Pay particular attention tonotes on ventilation.

Cornice and PelmetThe cornice and pelmet should be cut using amitre block and saw. Follow the diagram for thecorrect angles.Different styles of cornice and pelmet are fitted inslightly different positions. See the illustration forguidance. Section A-A shows the view from theside and how the items overhang the doors.Section B-B shows the view from the front andhow the items overhang the sides.Drill 5mm holes or attach half blocks 50mm in fromeach end and every 450mm along stright sections.

90°

45°45° 45°

45°

45°45°

135°135°

90°

A

B B

A

B-B(Front view)

Section A-A(Side View)

45°45°

D o o r


B-B (Front View)

Xmm

Xmm


D o o r

B-B (Front View)

Xmm

5mm

Door Door

Step 11 - Flooring and Plinth

Lay flooring. The flooringusualy stops at the legs butwill need to continue underunits with decorative legs.Fit the plinth. The plinth mayneed to be trimmed to allowfor irregularities in the floor.

A return plinth is made from asection of continuous plinth. Itwill need to be notched to fitaround the legs. It is fittedbehind the plinth along thefront. Any cut edges shouldbe covered with the suppliededging tape using contactadhesive.On the return, fit the plinthclips the other way up toavoid clashing with the plinthclip on the front.

5 2 5 m m

5 4 m m

6 0 m m

3 2 4 m m

Trim to suitthe wall

2 4 m m

3 8 4 m m

Return Plinth

==

Edging Tape

1 4 0 m m

P l i n t h

F l o o r

C o v e r i n g

Floor

ContinuousPlinth

= =

==

==

Xmm being the thicknessof the door.


23/52

23

Step 12 - Fit the Doors and Drawers

Assemble and fi t the drawer boxes.Fit the shelves.Hang the doors. Refer to pages 26 to32 for more information. Refer toinformation included with theappliance for information on fittingintegrated appliance doors.

Activate soft c lose mechanism or fitsoft close buffers if applicable. Smallerdoors need only one softclose buffer.Larger doors user two softclosebuffers. Use cover caps as required onexposed hinges. Refer to the assem-bly instructions.Fit the drawer fronts.Drill the door and drawer fronts for thehandles. On the 925x925 L-shapedbase and 625x625 L-shaped wall, onlyone handle is required, refer to page27 for further information on L-Shapedunits.Refer to page 33 to 36 for moreinformation on handle drilling.NOTE: Fit any wirework required thisstep. Refer to manufacturers instruc-tions for information on how to fit.

Softclose ON

Softclose OFF

(107 ° Hinge SoftClose Activation)

(170 ° Hinge SoftClose Buffer fix)

(Hinge Covercap Fix)


24/52

24

Section 5: Finishing Touches - Decor Panel FittingScribing to the WallPosition the unit. Clamp the show end to the unit so that is it just touching the wall. Measure the overhang at the front of the unitand subtract the amount needed to overhang the door. Cut a small block of wood to this size and by placing it against the wall,draw a line parallel to the wall onto the Show End. Trim the show end along the line. If desired, the fit can be tested on a piece of

the packaging before cutting the Show End.

Wall and Dresser UnitsThe Decor Panel is supplied 30mm deeper than the carcase to the allow for scribing to the wall at the back and overhanging thedoor at the front. The amount of overhang depends on the thickness of the door. The bottom of the Decor Panel can either be leftto enclose the pelmet (Option A) or the top trimmed so that the bottom of the Decor Panel is flush to the bottom of the unit and thepelmet fitted underneath the Decor Panel (Option B). See page 21 for hints on concealing screws.

Bottom of Wall Unit

Base and Appliance/Larder UnitsThe Decor Panel needs to be cut down to suit the height ofthe unit once it has been installed. The Decor Panel shouldoverhang the front of the cabinet and continue to the floor.The Decor Panel is supplied 30mm deeper than the cabinet toallow for scribing to the wall at the back and overhang thedoor at the front. The amount of overhang depends on thethickness of the door. The bottom and back can be scribed tothe floor and wall and the raw edge must be sealed with asuitable sealer. See page 21 for hints on concealing screws.

Overhang

5mm

4x30mmx4 per Show End

Scribeto thefloor

Scribeto thewall

Scribeto thewall

Scribeto thefloor

Trim tocorrectheight


Overhang

5mm

Scribeto thewall

Overhang

5mm


(Option A)

(Option B)

(Option A)(Option B)


25/52

25

Tall Curved Corner PostsThese posts are used in conjunction with standard decor panels to finish your kitchen. They are 2400mm high as standard and are cutdown for use with base, wall, tall wall and tall units.

Plinth FittingWhen used with a base or tall unit the plinthruns into the corner post/decor panelassembly.

Modern/Contemporary Cornice andPelmetWhen used with a wall or tall unit that hasmodern/contemporary cornice, the cornice isrun into the corner post. The post and decor

panel is fitted above the unit as shown.

The pelmet is run into the corner post also,with the post and panel fitted below the unitas shown.

Classic/Traditional CorniceWhen used with a wall or tall unit that hasclassic/traditional cornice, the cornice goesabove the panel and post. A special cornerpiece is used to run around the curve. The

post and decor panel is fitted in line with theunit as shown.

The pelmet is run into the corner post, withthe post and panel fitted below the unit asshown.

100mm

Xmm

Base and Tall Unitfitting position

30mm

125mm

Decor Panel

Corner Post

Packer

50mm

Xmm

Wall Unit fitting position

75mm

30mm

Decor Panel

Corner Post

Packer Fix the decor panel to the corner post andpacker using 30mm countersunk screws (notsupplied). Ensure screws are flush withcorner post/packer for a flat finish with unit.Offer the corner post/decor end panelassembly to the unit. Measure the thicknessof the fascia and set the corner post forwardof the unit by this dimension (X) to achievean in line finish. Scribe the rear of the decorend to the wall, ensuring the raw edge issealed.Secure the assembly by countersinking30mm screws (not supplied) through fromthe inside of the unit to the dimensionsshown within the units.

(Not Supplied)4x30mm


26/52

26

Section 6: Finishing Touches - Door Installation

Please spend five minutes reading this section after the unit havebeen assembled and fitted but before you start to fit the doors

For timber doors, drawer fronts and accessoriesUnpackingThe doors, drawer fronts and some accessories of a Wickes Kitchen are manufactured fromcarefully selected solid timber/veneers of the finest quality.

As with most things in nature, there is a degree of variation in both colour and graining. Thesedifferences are part of the special character and beauty of wood, differences which make a woodkitchen such a desirable product.

Any large differences in tone apparent when the kitchen is first unpacked will diminish over a fewmonths as the timber mellows with exposure to daylight to give a natural uniformity.

InstallationFor best results the doors and drawer fronts should be checked together. After unpacking, andbefore installing doors and drawers, it is recommended that they are placed against their respec-tive units in order to judge the final effect. Reposition any items to obtain the most even match.NOTE: It is not advisable to fit timber doors in newly constructed or recently plastered rooms. Ahigh moisture content in the environment may cause the doors to swell and split. It is recom-mended that doors are stored in a suitably dry environment outside the kitchen until the room hasdried out thoroughly.

Hinges and DrawersOnce you’re happy with the overall effect fit the hinges and drawer boxes. Attach doors and draw-ers to the cabinets taking care not to damage the lacquered surfaces. When all items areinstalled and you have checked the results, attach the handles.

HandlesSee pages 33 to 36 for information on handle fitting.Note: Any doors or drawer fronts which have been fitted with hinges or drilled for handles cannotbe returned to store.

Self-Adhesive Edging TapeSelf-adhesive edging tape is available to colour match the doors. It is applied to the front edges ofthe cabinet. before attaching the doors. The edge of the carcase must be clean, dry and free fromdust and grease. Apply the tape carefully. Press the tape down firmly with a clean, hard roller orsimilar tool to ensure good adhesion. Trim any excess with a sharp knife.


27/52

27

Fitting Fascias to L-Shaped Corner Base Units

Fitting Fascias to L-Shaped Corner Wall Units

This unit is supplied with two fascias, one handle andone corner filler. The filler is NOT even on each sideand must be fitted to one door as shown below. Decidewhich door is to have the filler, the other door will havethe handle fitted to it. Fitting the filler the incorrect waywill stop the doors from closing.

Do not put the handle on the door with the filler. One soft close bufferis fitted to each door. The other hinges are fitted with cover caps.Refer to page 33 for information on drilling the door for a handle.

This unit is supplied with two fascias, one handle andone corner filler. The filler is NOT even on each sideand must be fitted to one door as shown below. Decidewhich door is to have the filler, the other door will havethe handle fitted to it. Fitting the filler the incorrect waywill stop the doors from closing.

Do not put the handle on the door with the filler. One soft close bufferis fitted to each door. The other hinges are fitted with cover caps.Refer to page 33 for information on drilling the door for a handle.

x16/323.5x12mm

x2/6 Note: Some fascias mayrequire 35mm Cover Caps.

C

A

B

Right

Left

A

B

C

x2

x2

x4

C

A

B

Right

Left

A

B

C

x2

x2

x4

x163.5x12mm

x2 Note: Some fascias mayrequire 35mm Cover Caps.

5 5 m m

5 2 m m

2 8 m m

2 5 m m

Note: Corner post notrequired on Esker ranges.

Note: Corner post notrequired on Esker ranges.


28/52

28

Fitting Fascias to Closed Corner Wall UnitsThis unit is supplied with one fascia and a blankingpanel. The fascia uses two specific blind hinges to fix itto the blanking panel. It is advisable to fit the hingeplates to the blanking panel before fixing unit to thewall.

Clip the hinge onto the hinge platethen adjust door as required.

x43.5x12mm

Note: Some fascias mayrequire 35mm Cover Caps.

x2

B

A

C

A

Soft Close Activation

Soft Close Deactivation

B

C


29/52

29

Framed Fascias Fixing - Pilot Hole DrillingFor fascia packs with frame and separate open fascia ONLY

Please Note: If a fixed frame fascia is to be used do not pilotdrill the carcase.For units with frames that are separate from the doors it isrecommended that the end panels and mullions of the unitsare pilot drilled or marked with a bradawl where indicated witharrows in the illustrations. The mullion needs to be drilled onboth sides.The second position 64mm up and down from these holes canbe used if it is necessary to move the fixing bracket.

For Base Units the frame should be fitted flush at the bottom ofthe carcase which will leave a 4mm gap at the top.For Wall Units and Dressers, the frame should be fitted centrallyon the unit which will leave a 2mm gap at the top and bottom.For Appliance Housings and Larders the frames should be fittedflush at the bottom but a 2mm gap should be left at the top. Ifrequired the position of the extra hole can be taken by measur-ing the frame to be fitted in that position.For the 300 Pull-out Larder leave a 2mm gap between theframes.

Dresser

All Base Units

20.5mm

B a s e m u l

l i o n

Top37mm

1 1 3 1 m m

1 1 5 m m

39mm Top 6 4 m m

6 6 1 m m

6mm

6 4 m m

16.5mm

6 6 1 m m

1 0 1 m m

5 3 3 m m

Appliance Housings and Larders

1 0 1 m m

2 3 9 m m

( 4 3 7 d o o r

)

3 6 7 m m

( 4 3 7 d o o r

)

3 8 6 m m

( 5 8 4 d o o r

)

5 1 4 m m

( 5 8 4 d o o r

)

1 1 2 7 m m

( 1 3 2 5 d o o r

)

5 3 3 m m

( 7 3 1 d o o r )

6 6 1 m m

( 7 3 1 d o o r

)

35mm

2 2 0 m m

( 2 9 0 d o o r

)

All Wall Units

35mm

6 4 m m

6 4 m m

6mm

6mm

6 4 m m

6 4 m m

1 0 1 m m

35mm 6 4 m m

6mm

6mm

TopTop

6mm

6mm

6 4 m m

6 4 m m

5 0 mm

5 0 mm

Top/Bottom Panel(Double Door Wall Units Only)

5mmFront

Drilling Dimensions

3mm

2.5mm


30/52

30

Right Hand Frame

Left Hand Frame

BaseUnits

No Power Screwdrivers

WallUnits

Double Door Wall Units

All Base Units

Single Door Wall Units

WallUnits

Please Note: The brackets used to fix the frame tothe carcase are designed to grip the frame as theyare screwed to the carcase side panel.See details on previous page about pilot hole drillingthe carcase.

Do not use a power screwdriver for this step.

Framed Fascias Fixing - Fitting the Frames

x4x43.5x15mm

Frame Frame

Carcase

x4x43.5x15mm

x43.5x15mm

x4


31/52

31

x 2 per door

Screw the bracket to the top and bottom of the carcase behind the frame.

x2 per hinge

x2 per door

x2 per door

x2 per door

Fitting the Softclose and Buffer Brackets

The hinge plates are attached to the unit withthe system screws shown here.

x2 per hinge

Fitting the Doors to the Units Removing the Door Lift the tab to release the hinge.

Fit the Softclose buffer to the hinges oneach door.

x2 per door

800 and 1000 Wall Units ONLY

All Wall and Base Units EXCEPT 800 and 1000 Wall Units

Fitting the Hinges to the Doors

Framed Fascias Fixing - Fitting the Door Please Note: The door on a single unit may open either left or right. Before attaching hinges to the door, check with the kitchenplan which opening is required and fit hinges to the appropriate side.For a framed kitchen there can be two types of hinges used within the build, one type (standard hinge) for fascias with afixed-frame, the other (framed hinge) for fascias with a frame and door that moves seprarately.For the 800 and 1000 wide wall units the bracket for the door buffer must be fitted to the top and bottom panels. All other unitshave the bracket for the door buffer mounted on the side of the carcase or the mullion.

3.5x12mm

3.5x15mm

Frame



32/52

32

AB C

Standard Fascia Fixing - Fitting the Door and Fascia AdjustmentsDoor AdjustmentPlease Note: The door on a single unit mayopen either left or right. Before attachinghinges to the door, check with the kitchen planwhich opening is required and fit hinges to theappropriate side.

x 2 per door A - Vertical C - HorizontalB - Lateral

Corner Unit Hinge

Standard Hinge

Loosen screw “A” on allhinges. Adjust door andretighten screw.

Loosen screw “B”. Adjust door andretighten screw.

Loosen screw “B” ½ turn . Turnscrew “C” until door is positionedcorrectly and retighten screw “B”.

Fixed Frame Door Hinge

Softclose ON

Softclose OFF

x2 per hinge3.5x12mm


(107 ° Hinge Soft

Close Activation)

C A

B

A

B

C

CB

A


33/52

33

Door and Drawer Handle Drilling A range of handles are offered to finish your kitchen, or you can choose your own. Getting the handles in the rightposition is important when designing and installing your kitchen.

Before you startConsider where you want the handles on the door. They can be central on the door or to the left or right.Think about the overall kitchen plan and consider any possible handle clashes, particularly L-Shape corner units.Refer to page 27 for further information.

Check which side of the door opens before marking and drilling holes.Drawers and pull out/down doors should always have the handles located centrally to allow the unit to operatecorrectly.Tower units should have handles placed where they will ensure they flow with the design of the kitchen and operatecorrectly.

A template can be used to place handles in the same position on all the doors.Use a piece of scrap wood behind the door where you are drilling to reduce the chance of the surface splinteringwhen the drill bit goes through.Before drilling, use a bradawl to make a small point. This will allow the drill to sit on the hole and prevent it slipping.If your fascia already has any pin prick marks, DO NOT use these.Don’t over-tighten screws to avoid splitting the fascias.

The following are the recommended door handle positions for different door styles. However, it is up to you todecide what works best for your kitchen.

••

••

•

••

•

•

Door StyleSlab

Handle

D and Bar Handles verticallymounted on Base Unit.Dashed line shows exampleof top centre.

Shaker Framed

Top centre of handle is45mm in and 45mm downfrom the top.

Top centre of handle iscentral to vertical (stile)and horizontal (rail) frame.

Top centre of handle iscentral to vertical (stile)and horizontal (rail) frameof central panel.

D and Bar Handles verticallymounted on Wall Unit.Dashed line shows exampleof bottom centre.

Bottom centre of handle is45mm in and 45mm up

from the bottom.

Bottom centre of handle iscentral to vertical (stile)

and horizontal (rail) frame.

Bottom centre of handle iscentral to vertical (stile)and horizontal (rail) frameof central panel.


34/52

34

D and Bar Handles horizontallymounted on Base Unit. Dashedline shows example of topcentre in vertical plane.

Top centre of handle iscentred to the door width45mm down from the top.

Top centre of handle iscentred to the door widthand central to the horizontal(rail) frame.

Top centre of handle iscentred to the door widthand central to the horizontal(rail) frame of the centralpanel.

D and Bar Handles horizontallymounted on Wall Unit. Dashedline shows example of bottomcentre in vertical plane.

Bottom centre of handle iscentred to the door width45mm up from the base.

Bottom centre of handle iscentred to the door widthand central to the horizontal(rail) frame.

Bottom centre of handle iscentred to the door widthand central to the horizontal(rail) frame of the centralpanel.

Top end of handle is 45mmin and 45mm down fromthe top.

Top end of handle iscentral to vertical (stile)and horizontal (rail) frame.Note: Ensure handleattachment does notinterfer with the joins.

Top centre of handle iscentral to vertical (stile)and horizontal (rail) frameof central panel.Note: Ensure handleattachment does notinterfer with the joins.

D and Bar Handles horizontallymounted to side of Base Unit.Dashed line shows example oftop end in vertical plane.

D and Bar Handles horizontally

mounted to side of Wall Unit.Dashed line shows example ofbottom end in vertical plane.

Bottom end of handle is45mm in and 45mm upfrom the base.

Bottom end of handle iscentral to vertical (stile)and horizontal (rail) frame.Note: Ensure handleattachment does notinterfer with the joins.

Bottom centre of handle iscentral to vertical (stile)and horizontal (rail) frame

of central panel.Note: Ensure handleattachment does notinterfer with the joins.


35/52

35

Centre point of handle iscentred to the door width50mm down from the top.

Centre point of handle iscentred to the door widthand central to the horizontal(rail) frame.

Centre point of handle iscentred to the door widthand central to the horizontal(rail) frame of the centralpanel.

Centre point of handle iscentred to the door width50mm up from the base.

Centre point of handle is

centred to the door widthand central to the horizontal(rail) frame.

Centre point of handle iscentred to the door widthand central to the horizontal(rail) frame of the centralpanel.

Centre point of handle is50mm in and 50mm downfrom the top.

Centre point of handle iscentral to vertical (stile)and horizontal (rail) frame.

Top centre of handle iscentral to vertical (stile)and horizontal (rail) frameof central panel.

Centre point of handle is50mm in and 50mm upfrom the base.

Centre point of handle iscentral to vertical (stile)and horizontal (rail) frame.

Centre point of handle iscentral to vertical (stile)and horizontal (rail) frameof central panel.

Knob and Cup Handles sidemounted on Base Unit. Dashed

line shows centre point ofhandle.Note: Ensure cup handleattachment does not interferwith joins.

Knob and Cup Handles sidemounted on Wall Unit. Dashedline shows centre point ofhandle.Note: Ensure cup handleattachment does not interferwith joins.

Knob and Cup Handles centralmounted on Pull out/downUnits. Dashed line showscentre point of handle.Note: Applicable only to pullout/down units to ensurecorrect operation of hinges.

Knob and Cup Handles centralmounted on Pull up Units.Dashed line shows centre pointof handle.

Note: Applicable only to pull upunits (including aventos) toensure correct operation ofhinges.


36/52

36

Fitting handles to drawers - Points to consider Remember: The centre points for each handle type as described in the previous pages should also be applied here.For the shallow/drawerline height drawers the following mounting is recommended: >D and Bar Handles - Top centre of the handle centralised to both the height and width of the drawer. >Knob and Cup Handles - Centre point of the handle central to the height and width of the drawer.For the deep height drawers ensure the handle top centre point or centre point is central to the width but align asfollows >Slab Drawers - 50mm Down from the top of the drawer. >Shaker/Framed Drawer - Central to the vertical (stile) and horizontal (rail).For double handle drawer fronts it is recommended to mount the handles equidistantly.

••

•

•

Example Handle Positions for Slab Style Drawers

Example Handle Positions for Shaker/Framed Style Drawers


37/52

37

Section 7: Finishing Touches - DrawerFitting and Other Internals

Please Note: Only the left side is shown, the right side is a mirror image.These images are for standard fascias only. For framed kitchens, see pages 38 and 39.

Drawer Box Runner Positions

98mm

684mm

392mm

245mm

684mm

317mm

Four Drawer Units

Using fascia packsFD34 and FD54

Three Pan Drawer Units

Using fascia packsFPD63 and FPD93

Two Pan Drawer Units

Using fascia packsFPD62 and FPD92

Drawerline Units

Using fascia packs FB3,FB4, FB5 and FB6

98mm

224mm

98mm

684mm

392mm

3.5 x 16mmx2x4

Fit as third screw

Front 1 x 'L'; 1 x 'R'

Drawer Runner

3.5 x 16mmx4x4

Fit as third andfourth screws

Front 1 x 'L'; 1 x 'R'

Drawer Runner

900mm Wide Units ONLY

600mm Pull Out Unit

227mm

49.5mm

31.5mm

31.5mm

49.5mm99mm

67mm99mm

67mm

End panelrunner positions.

Door drilling andbracket positions.Use a bradawl tomark for drawerbracket. Railholes are 10mmin diameter and12mm deep.

10mm

This unit used components from the Easy Space Kit. The upper two drawers are concealed drawers and assembled using theEasy Space instruction sheet. The bottom drawer is assembled the same way but the door fascia is fitted instead of theconcealed drawer fascia. Drawer box is fixed to the fascia with the drawer brackets. Follow instructions supplied with EasySpace and fit the drawer runners and packers for the 735mm Highline unit. Packers are fitted to the right side only.The door fascia needs to be drilled and holes for the brackets started with a bradawl as indicated. Brackets are fit offset on oneside for the packers. Fit brackets to the fascia and assemble drawer box using the door fascia instead of the conceal drawerfascia.


38/52

38

x12Ref. No. 154080

Framed Fascias Fixing - Drawer Packers and Runner Positions

9 8 m

m

37mm 224mm

Drawerline Units

Packer Locations: Only the left side is shown. The right side is a mirror image. For a framed kitchen, packers must be fitted forthe drawers to open clear of the frame. Framed kitchens are only available with the tandem box drawer system. Packers must befitted the correct way up so please make sure that the holes at the top of the packer are 12mm down as shown.Please Note: On the Pan Drawer and 4-Drawer packs it is difficult to fix the bracket for the fixing frame if the bottom runner isfitted. Use the lower bracket position on the frame and fit the bottom runner after the frame has been fitted. (Marked with * below)

Four Drawer Units

Three Pan Drawer Units

5 6 0 m m

3 9 0 m m

1 2 m m

1 0 4 m m

x4

Ref. No. 154004

165mm 224mm

1mm

1 2 m

m

x4Ref. No. 1501264x30mm

x4Ref. No. 154080

x16Ref. No. 1501264x30mm

2 4 5 m m

6 3 7 m m

37mm 224mm

37mm 224mm

x8

Ref. No. 154004

5 6 0 m m

3 9 0 m m

2 1 8 . 5 m m

1 2 m m

1 0 4 m m

x16Ref. No. 154080

x16Ref. No. 1501264x30mm

2 4 5 m m

6 3 7 m m

37mm 224mm

37mm 224mm

x8

Ref. No. 154004


39/52

39

Crossrail Packer for Drawerline Units Dresser UnitsPlease Note: The Centre Drawer Rail must be fitted in the position shown here.Before attaching the drawer runners to the packers drill through the packer thenfix the packer to the mullion with a 32mm screw as shown.

Please Note: The packer for the dresser isfitted 18mm up from the bottom of the endpanel. It may be easier to locate the packerby temporarily putting the unused bottompanel into position and fixing the packerabove it.

CentreDrawer rail

Drawer Runner Position

Mullion

x1

Ref. No. 154084

x1

Ref. No. 154083

70mm

36mm 352mm

Drill and fit a 4.5 x 32mm screwin the position shown.

96mm164mm 1 4 m m

20mm

20mm

1 x 'L'; 1 x 'R'

5mm

x4

Ref. No. 154004

x6Ref. No. 1501264x30mm

3.5 x 16mmx2

Fit as third screw

x4Ref. No. 154080

224mm37mm

1 8 m m

x4Ref. No. 1501264x30mm

x4Ref. No. 154080

Start Locked

Do Not Over Tighten


40/52

40

150mm Pull Out Units with WireworkPlease Note: Refer to the fitting instructions supplied with your wirework.

x6

Right-handfixing

Left-handfixing

Fit the prongs on the back of the runner into the drilled holes and fixthrough the star shaped holes indicated. It will be necessary to move theouter runner rails to get access to the holes.These drawings show the positions for mounting the unit on the right handpanel. Reverse the positions for the left hand side.Caution: Some parts of the runner are sharp. Handle with care.

Before attaching the frame to therunners. The following steps mustbe complete. First the softclosecatch must be pushed to the backof the mechanism until it clicks.Then the centre section of thedrawer runners must be pulledforward before attaching the frame.The keyhole slot goes over thescrew on the runner. After fitting,tighten the screw.Note: The softclose catch is at thetop of the frame when fixing to theright hand side and at the bottomfor a left hand side fixing.

InsideFace

Right-handfixing

InsideFace

Left-handfixing

The holes for the brackets shouldbe marked using a bradawl. Referto the wirework instructions formeasurements.

Supplied with wirework4.5x15mm

x84.5x13mm

Supplied with wirework

Checkwireworkinstructions fordirections onaltering fasciaposition to fit.


41/52

41

Section 8: Finishing Touches - Curved Units

925mm Internal Curved Base UnitsPlease Note: For complete assembly instructions please refer to leaflet provided with unit.

Please note: When double doorsare to be fitted a supplement hingepack KQQ17HCS is required.

x2

Single Door

1 x Left Hand1 x Right Hand1 x KQQ17HCS Pack

Double Doors

Connect units together as per step 5, page 19 of this guide, and fix to the wall with appropriate fixings. Conceal connecting bolt as persection 5 page 19. This unit is fitted right into the corner of the room. The shelves can be fitted after installation.

Continuous plinth

The curved plinth is supplied separately. Curved plinth isconnected to the continuous plinth on both sides using thebrackets and screws provided.

Continuous plinth

Depending on the kitchen range, there will be one or two doorsto fit. See below for fitting details.

x2

x2

5mm

x2

x10

x83.5x12mm

A

B

C

Right

Left

x4/83.5x12mm

x2/4

x2/4


42/52

42

625mm Internal Curved Wall UnitsDepending on the kitchen range there will be one or two doors to fit. If there are two doors, the unit must be fixed with two 300mm wallunits (one either side) to make it into a unit that requires 925mm in each direction on the wall. This covers both the standard height andthe tall height variants.

Please Note: The arm on the Hanging Bracket must be fully extended before it can be hooked through the opening in the back. Make surethe Bracket is pushed firmly against the back and top before fixing.

Fix wall brackets in correct location, as advised in step 7 page 20 of this guide. Hang Corner unit and adjoining units and fix together. Referto step 5 page 19 of this guide for details on concealing the connecting bolts. If unit is with two doors, the two adjoining units must be the300mm wall units, as shown in the image.

G l u e

For the cornice and pelmet, before fitting to the units it is recommended that the curved pieces are glued to the straight pieces otherwise itmay be difficult to achieve an exact join at a later stage. Once completely dry, fix assembled cornice and pelmet to the units as advised in

step 10 page 22 of this guide, with an overhang the same thickness as the fascias (X).

Recommended Screw(not supplied)

1 x Left Hand1 x Right Hand1 x KQQ17HCS Pack

Double Doors

Please note:When doubledoors are to befitted asupplement hingepack KQQ17HCSis required.

Depending on the kitchen range, there will be one or two doors to fit. See below for fitting details.

Carcase

Carcase

X mm

625mm Internal Curve unit with one door.

625mm Internal Curveunit with two doors andtwo 30mm units added.

25mmx1 Right Handx1 Left Hand

x44x30mm

5mm

x2

x2x10

x44x30mm

X mm

x2/4

Right

Left

Single Door

x2/4x4/8

3.5x12mm


43/52

43

External Curved Base and Wall UnitsThe holes for the hinge plates need to be drilled through from the back.The sides of the unit are different sizes so make sure that only the correctside is drilled. The unit is turned over to reverse the position of the longand short sides. Drill the holes in one panel only.

For framed kitchenranges it is important tobe careful when makingholes in the cabinet tofix the frame as thedimensions at the topand bottom of the unitare different on wall andbase units. Refer to

page 29 for details onfitting frame brackets.

Wall Units:X = 101mm Y = 101mm

Base Units:X = 103mm Y = 99mm

Important: Align the fascia with the cabinet as it can only be fitted one way.Fix the hinges in accordance with your opening preferences. The unsprung hingemust be used for handleless units. Refer to pages 31 and 32 for further details onfitting and adjusting hinges for standard and framed fascias.

StandardFascias

FramedFascias

For framed kitchens, screwthe bracket for the buffer tothe side of the carcasebehind the frame.

Importan

wickes kitchen self fit customer care guide

Documents