WFXT optics: design optimization and developmentGiovanni Pareschi*JKCS041:, z = 1.8, Andreon et al., 2009

* R. Giacconi, A. Ptak, C. Norman JHU S. Murray, A. Vikhlinin CfA M. Weisskopf, R. Elsner, S. ODell, B. Ramsey NASA/MSFC S. Borgani, P. Rosati, P. Tozzi INAF/OATrieste S. Molendi INAF/IASF- MilanoThank you to the whole WFXT collaboration for supporting this work and for many useful discussions!AcknowledgementASI is supporting the pre-Phase A study in the context of the contract High Energy Astrophysics Studies . INAF is also funding the activities with internal resources.The WFXT optics team at OABPaolo Conconi, Sergio Campana , Oberto Citterio, Marta Civitani, Vincenzo Cotroneo , Giovanni Pareschi, Laura Proserpio, Gianpiero Tagliaferri , Giancarlo Parodi, (BCVProgetti)

Introduction the optical design of wide-field X-ray telescopes

Optical design & Optimization of the WFXT mirrors A few remarks on manufacturing and implementation of the WFXT opticsOutline *

WFXT payload top level requirements Number of X-ray optics modules: 3

Total payload (optics + detectors) mass: 1440 kg*

GraspGrasp = Aeff x FOV measured at 1.5 keV in cm2 deg2 Grasp measures the speed in which a survey can cover an area of the sky down to a given flux limit.

Better angular resolution results in better efficiency and source identification.*

WFXT*eROSITAXMMROSATIXOChandraGrasp(cm2 deg2)90001150900630150050HEW across the field(arcsec)5/1020-4015-2515-40~51-5

*H. Wolter, Ann. Der Phys., NY10,94Wolters solution to the X-ray imaging

Wolter I optical system*

ABRIXAS cross scancalculationOff-axis angle [arcmin]HEW [arcsec]Wolter I Point Spread Function (PSF)ABRIXAS/e-RositaCredits: MPE

A further extension of this line of thinking is that experiments could be designed by modelling both the hardware and software as part of the initial design. I myself, together with Richard Burg and Chris Burrows, used this approach in designing in the 1980s what I believe was one of the best experiments I ever conceived. The purpose was to scan the sky and to detect distant clusters of galaxies through their X-ray emission.

The idea was that it would be possible to equal or exceed the sensitivity of Chandra with an X-ray telescope of one tenth the area (and cost). This could be achieved by dedicating an entire mission of a small satellite to this purpose and by designing a telescope that would have a >16-fold increase of the field of view with respect to Chandra. ..

R. Giacconi, AN EDUCATION IN ASTRONOMY, ARAA. 2005.43: 1- 30, 22

X-ray optics with polynomial profile: general remarks Mirrors are usually built in the Wolter I (paraboloid-hyperboloid) configuration which provides, in principle, perfect on-axis images.

This design exhibits no spherical aberration on-axis but suffers from field curvature, coma and astigmatism, rapid degradation with increasing off-axis angles

More general mirror designs than Wolter's exist the primary and secondary mirrors are expanded as a power series

Optimization of polynomials increase the angular resolution at large off-axis positions but degrading the on-axis performances*See Burrows, Burgh and Giacconi (1992)

Why short mirror lengths for WFXTThe aspect ratio mirror shell length / focal length plays a very important role; in general the height of the shells should be kept as short as possible

With short mirror shells the spherical aberration contribution to the PSF is reduced; moreover a better control of the curvature of the field is achieved

a = on-axis incidence angle = angular off-setL = mirror heightF = focal lengthVan Speybroeck & Chase, Appl. Opt., 1971 A typical aspect ration between focal length and mirror shell of 14 - 15 must has to be taken (this was for the old WFXT design), but it should change in the interval 10 30, depending on the f-number. N.B.: short mirror shells increase of the manufacturing problems!*

Optimization of the Single Mirror Shellf = Focal Length / Shell Entrance Radius l = (100 x Total Mirror Length / Focal Length)Best merit function for optimization of surveying telescopesSimplified formula for the HEW of a polynomial optics (BBG, 1992) weighted over the FOV coming from the optimizations (Conconi et al., Applied Optics , 2009, submitted)*

Image quality for different f x l productsf = 5 ; l = 10

f = 7.1 ; l = 7.1

f = 10 ; l = 5*(Conconi et al., Applied Optics , 2009, submitted)

Polynomial shell (f = 5, l = 7) versus Wolter I and W-S *(Conconi et al., Applied Optics , 2009, under submitted)

Aberration Analysis *(Conconi et al., Applied Optics , 2009, submitted)(f = 5, l = 7)

Butterfly-like configurationIn order to maintain the same focal plane curvature, and the same f x l product the length L should change along the series of nested shells.Butterfly-like assembly must be used, with mirror shells shorter at the center.The curvature of the field is dependent on f1.8:*See Conconi and Campana, 2001 Conconi et al., 2004 - Conconi et al., 2009

Intersection planes at different focal distancesEven if with different height along the series, images produced by different mirror shells do not superimpose exactly, having different plate scales and then they have not the same best focus positions (plate scale problem)

The problem is attenuated by using mirror shells with intersection planes at different positions (i.e. they have to be moved relatively to each-other)

See Conconi and Campana, 2001 Conconi et al., 2004 - Conconi et al., 2009

*

Shift among the intersection planesThe plate scale of the shells is different along the series of nested shells. If not corrected the effect that the focal spots of different shells do not coincide.20 arcmin off axisFL = 1 mOutermost and innermost mirror shellsCorrection for 1 m focal lengthIn order to correct the effect a shift among the intersection planes has to be introduced.*

Angular resolution optimization strategyUse of 3-order polynomia (x 2) for optimizing the parabola and hyperbola

Figure of merit: Number of modules: 3 Diameter: large enough for compliance with requirements effective area maximization Effective Area per resolution element*

Sag of the first polynomial mirror wrt a Wolter I*

Optimization of the acceptance angle17 arcim is chosen as acceptance angle for the whole set of shells*

*In order to reduce FEM dimensions only 9 MS have been included in the model.MSs # 1-16-31-46-62 have been modelled with their real characteristics (thickness and material).They have been used for the evaluation of the optical degradation by ray-tracing.In between there are four dummy MSs having mass and stiffness respectively equivalent to the MS groups:

from #2 to #15 from #17 to #30from #32 to #45from #47 to #61Interface with spoke wheels: effects of the axial displacements

Mirror modules parametersN.B: the weight was calculated for the full set of shells concerning the 3 mirror modules; at least 30 % more should be accounted for the mechanical structure*

Effective area for SiCCoating: Pt + C overcoating*

Effective area for GlassCoating: Pt + C overcoating*

Why Carbon overcoating?N.B.: spider vignetting not included

Measured reflectivity of Pt and Pt+C

Focal spots at different angular off-sets (1 keV)0 arcmin5 arcmin10 arcmin15 arcmin20 arcmin25 arcmin*

HEW for the mirror module (theoretical design)*

Main technical aspects

mechanical behavior closer to a belt-like configuration rather than a tube-like

border effect errors with a much higher weight in determining the PSF

angular resolution more strongly affected by the slope errors caused by out-of-phase azimuthal errorsThe realization of mirror shells with a small aspect ratio ( length/diameter more than 3-4 times lower than XMM and Chandra) increased difficulty in reaching very good angular resolution:*

*Past and future X-ray telescopes: HEW vs. the Mass/Collecting-Area ratioIXO

*FEM analysis: short vs. long mirror shellsExample: LOADINGS GIVING SMALL SPATIAL SCALE DEFORMED SHAPE (i.e. the deformed shape affects small portion of MS surface (at least in long MS) with strong and local displacement gradients):Loading 5: twelve tangential moments (10Nmm each) applied at front section in 12 point 30 spaced. Loading 6: twelve outward radial forces (0.1N each) applied at front section in 12 point 30 spaced.

Why SiC and Glass for the WFXT mirrorsHigher rigidity mirror shells, based on materials with:

low density (to increase the wall thickness)

good mechanical parameters such as SiC and Glass

can be the solution for the above mentioned problems

*

MS MaterialDensity [t/m3]YoungE [GPa]PoissonRatio CTE (1)[K-1]Ther. cond.[Wm-1K-1] (1)Bending merit figure (2)Electrof. Nickel8.81800.312.710-6601.0 Glass 3)2.5172.90.2087.210-60.9316.6Fused Silica (HSQ300)2.272.50.170.5510-61.3824.2CVC SiC3.184560.212.3310-614051.1

see O. Citterio, et al., , SPIE Proc., 3766, 198 (1999) Ghigo et al., SPIE Proc., 3766, 209 (1999) WFXT (epoxy replication on SiC) = 60 cmHeight = 20 cmF. L. = 300 cmHEW = 10 arcsec @ 0.1 keVTests @ Panter-MPE & Marshall XRFWFXT heritage (SiC by epoxy replication) Ni replication with same mandrel = 60 cmHeight = 20 cmF. L. = 300 cmHEW = 35 arcsec @ 0.28 keV*

Direct polishing approach for WFXT mirror shellsElectroformed NiDirect polishingChandra, Rosat (0.5 3)XMM Newton, Jet X, Swift (15)Angular resolutionEffective areaDirect polishingElectroformed NiTechnology provedTechnology under developmentDifficult achievement*LEGENDA:

Materials for carriersTwo materials under investigation:

SiC (CVD for allowing the polishing)

Glass (Fused Silica)

SiC CVD Pros outstanding T/M parameters already used in space applications low density polishable up to 2 AngstromSiC CVD Cons very hard (long time for polishing) costFused Silica Pros well known material already used in space applications low density polishable up to 2 Angstrom (very easy) available just on thick tubes (to be grinded!) T/M parameters lower than SiC Fused Silica Cons*

Processes envisaged for the mirrors production*

During metrology and polishing (just for glass and CVC SiC) operations the MS in vertical position (axial gravity) rests on astatic supports, which contrast the gravity by controlled axial forces.

The astatic support number has to be computed in a way that the gravity deflections are sufficiently small. Mirror shell on astatic support (1) *

Direct polishing & metrologyAdvanced technologies but thy have to be tested on thin shells asap*Credits: Zeeko, UK

Glass tube of Heraeus HSQ 300 during grindingCredits: Heraeus, GermanyTypical working time: 1 week/shell with 1 machine (but it can improve)*60 cm5 mirror shells already ordered (60 cm diam , 1.5 mm thick; + 4 48 cm diam, 1.5 mm thick).They will be used for direct polishing testing.

Credit: TREX, USATypical deposition time: 100 mm / hour (a couple of days for a shell production)Stress- free CVD SiC material available*1 mirror shell already ordered ( 30 cm diam; 1.5 mm thick). A secvond (60 cm cm; 1 mm thick) is available from past projects.

They will be used for direct polishing testing.

Rough SiC shell produced at TREX*

Jig for metrology and machining*

*

Thank you!*

****Point spread function*Prova

******Prova

**