wft pozo multilateral
TRANSCRIPT
8/11/2019 WFT Pozo Multilateral
http://slidepdf.com/reader/full/wft-pozo-multilateral 1/2
Multilaterals
Applications
Features, Advantages and Benefits
Weatherford's SRS 1.1 selective re-entry system creates Level 1 junctions with full lineraccess to the lateral wellbore in new and existing open-hole environments. It allows fornumerous, closely-spaced sidetracks from the parent well. It also enables re-entry ofany lateral while maintaining access to the parent bore through a large-diameter packer.
The SRS 1.1 system is based on proven Weatherford technology that incorporates amultilateral orienting latch assembly, which is used for both milling and production, andan orientation riser (O-Riser). The O-Riser, attached above an ACP™ annulus casingpacker, acts as a permanent downhole anchor and seal bore with a known azimuthreference. The orienting latch allows for a repeatable-releasable whipstock connectionin a consistent orientation during the drilling or re-entry phase.
The dual-use orienting latch assembly, which is used in bothmilling and production, allows numerous sidetracks to bedrilled from the parent well. These closely-spaced lateralsprovide access to additional reserves with a smaller footprint, optimizing productionwhile reducing drilling costs and minimizing the impact on the environment.
The SRS 1.1 system allows for both open-hole and slotted liner completions. This
gives the operator the opportunity to meet the requirements of the application in themost economic manner.
A large ID packer provides access to the lower zone in the parent bore and the SRS system can be used for remedial work in any lateral wellbore. These re-entrycapabilities allow the operator to make improvements that extend the life of thewellbore and quickly restore maximum productivity.
The SRS 1.1 system is appropriate for Level 1 junctions in open-hole environments,either in new development drilling or re-entries. Based on proven technologies thatreduce trips and save rig time, it is ideal for building simple, low-cost and low-risk
junctions in consolidated formations.
The system is particularly suitable for wells in mature fields where production ratesare declining, because it allows economical, closely-spaced laterals to accessadditional reserves while maintaining production from the original wellbore.
TM
SRS 1.1–Level 1 Multilateral
© 2004–2007 Weatherford. All rights reserved. 4495.00
Weatherford International Ltd.515 Post Oak Blvd., Suite 600Houston, Texas 77027 USATel: 713-693-4000www.weatherford.com
8/11/2019 WFT Pozo Multilateral
http://slidepdf.com/reader/full/wft-pozo-multilateral 2/2
Multilaterals
Weatherford products and services are subject to the Company’s standard terms and conditions, available onrequest or at www.weatherford.com. For more information contact an authorized Weatherford representative.Unless noted otherwise, trademarks and service marks herein are the property of Weatherford. Specificationsare subject to change without notice. Weatherford sells its products and services in accordance with the termsand conditions set forth in the applicable contract between Weatherford and the client.
System size, openhole (in., mm )6
152.4 8-1/2
215.9
Hydraulic running tool maximum releaseachievable (PSI, kPa )
5,87240,482
6,24043,019
Maximum OD (in., mm ), O-riser 5.812147.6
8.125206.4
Minimum ID (in, mm ), O-riser/ ACP assembly3.95
100.36.25
158.8
Maximum temperature (°F, °C )275135
275135
Burst (PSI, kPa )2,500
17,235
4,000
27,576
Collapse (PSI, kPa)7,500
51,705 4,000
27,576
Whipstock angle 2° or 3° 2° or 3°Orientation accuracy 2.5° 2°
Stab-in force (lb, daN ), latch into O-riser 5,000 to 10,0002,224 to 4,448
5,000 to 10,0002,224 to 4,448
Release force (lb, daN ), latch from O-riser 30,000 to 40,00013,345 to 17,793
40,000 to 50,00017,793 to 22,241
Torque rating (ft-lb, N•m ), milling latch/O-riser10,00013,558
10,00013,558
Shear value (lb, daN ), starter mill from whipstock24,00010,676
24,00010,676
Minimum ID (in., mm )2.5
63.5 2.2557.2
Maximum OD (in., mm )4.72
119.96.5
165.1
Face angle 6° 6°
Running tool OD (in., mm ), J-slot release5.75
146.18.12
206.2
Production latch ID (in., mm )3.95
100.36.07
154.2
O-Riser/Annulus Casing Packer ( ACP )
Starter Mill/Whipstock/Milling Latch
Re-Entry Guide (Optional)
Specifications
TM
SRS 1.1–Level 1 Multilateral
The ACP™ system's hydraulic-release running tool features a mechanical back-up safety disconnect,ensuring reliable operations downhole.
The original O-Riser orientation is used to adjust the latch assembly for re-entry into the desired lateral.No gyro trips are necessary in the re-entry phase.
Features, Advantages and Benefits (continued)
© 2004–2007 Weatherford. All rights reserved. 4495.00
Weatherford International Ltd.515 Post Oak Blvd., Suite 600Houston, Texas 77027 USATel: 713-693-4000www.weatherford.com