welcome to qte training center! - cls energy · 29 beckhoff transfer course from twincat 2 to...

training

Welcome to QTE Training Center!

– 2 –

Discover the optimum.training

Successful companies consider the benefits of employee qualification and further training as an essential compe-titive advandays. These companies are investing nearly continuously in training and further education of their own employees. Their newly acquired expertise makes the employ ees not only more efficient at their workplace, but also more flexible and capable to manage other tasks profitably if required. QTE GmbH pro vides support for the qualification of your employees in a wide variety of areas and sectors.

We are happy to welcome you!

Successful companies consider the benefits of employee qualification and further training as an essential compe-titive advandays. These companies are investing nearly continuously in training and further education of their own employees. Their newly acquired expertise makes the employ ees not only more efficient at their workplace, but also more flexible and capable to manage other tasks profitably if required. QTE GmbH pro vides support for the qualification of your employees in a wide variety of areas and sectors.

– 3 –

Experienced trainersOur trainers have many years of ex-perience in the various areas of their expertise, as well as an advanced trai-ning as a teacher or respectively as an instructor. Therefore, you can rely on a well-balanced relationship between theory and practice.

We will come to you!Do you aim to quickly and easily perform the training within your own company, and you also have your own training room? No problem. With the QTE in-house training we can comfor-tably conduct your training measure on your own premises. Our trainer will travel to your company with all the required equipment. The only thing that you have to do is manage the participants, and we’ll take care of the rest! Take advandays of our attractive fixed-price offers.

Customer satisfaction… is important to us! To ensure the quality of our trainings, all participants do evaluate their own success after completion of the training and help to optimize our services by filling out a questionnaire. This allows us to take up improvements and new proposals.

Small study groups for optimal learning successTo guarantee optimal learning success we exclusively work in small groups consisting of a maximum of 6 partici-pants. Like this, we are able to focus on the demands of each participant individually and have the time -even if it might take a bit longer.

– 4 –


As an independent solution provider we are experienced with various PLC systems and offer a wide range of trainings based on SIEMENS and BECKHOFF standard modules as standard trainings respectively trainings specifically tailored to your needs. We would like to pass on our knowledge to you and your employees. Our team of skilled trainers place their profound knowledge from their own project experiences in Germany and abroad in a wide variety of sectors at your disposal by usingSIEMENS and BECKHOFF products.

You already are familiar with other automation systems and wish to work with SIEMENS respectively BECKHOFF products now? Fine, we take you there!

You need to refresh your skills or new approaches? No problem, we take you there!

We build on your existing knowledge and deal with your requirements and needs in a target-oriented manner. Our learning success is based on didacti-cally motivating learning contents and study techniques. During our training courses, we change between theory and practical units. You therewith en-sure yourself a great and sustainable learning success. Your new knowledge is immediately strengthened through practical applications using our own PLC models.

Your Trainings in the Area of Automation Technology

– 5 –

SIMATIC S7 Product Trainings 7 SIMATIC S7 - PLC Commissioning8 SIMATIC S7 - Troubleshooting for Maintenance and Service - Basic Course9 SIMATIC S7 - Troubleshooting for Maintenance and Service - Advanced Course10 SIMATIC S7 - for Programmers11 SIMATIC S7 - for Advanced Programmers12 SIMATIC S7 - Safety Integrated13 SIMATIC S7 - Graph Step Sequence Programming

SIMATIC S7 - TIA14 TIA - Troubleshooting for Maintenance and Service with TIA Portal - Basic Course15 TIA - Troubleshooting for Maintenance and Service with TIA Portal - Advanced Course16 TIA - Programming with TIA Portal - Basic Course17 TIA - Programming with TIA Portal -Advanced course18 TIA - Transfer course from S7 to TIA Portall19 TIA - Safety Advanced20 TIA - Step Sequence Programming with TIA Portal

S7 Networks20 PROFIBUS21 PROFINET

Visualization22 Visualization with HMI WinCC flexible23 Visualization with WinCC Comfort (TIA Portal)

Drive Technology24 Drive Technology Basics25 Drive Technology with SIMOTION and SINAMICS 120F26 Converter Commissioning, Parameterization and Communication

Machine Safety27 Machine Safety Guidelines

BECKHOFF Product Trainings28 Maintenance and Service with BECKHOFF TwinCAT 229 BECKHOFF Transfer Course from TwinCAT 2 to TwinCAT 330 Maintenance and Service with BECKHOFF TwinCAT 3

Content

– 6 –


SIEMENS Product Trainings

Your BenefitsAs global market leader SIEMENS offers established solutions for indus-trial machine and system automation. These are considered a global standard and used in almost every automated company. The advantages with SIEMENS controllers are their reliabili-ty and their system stability..

QTE SIEMENS product trainings involving SIMATIC S7, TIA Portal and Drive Technology

TIA Portal

TIA - Troubleshooting for Maintenance and

Service - Basic Course

SIMATIC S7

TIA - Troubleshooting for Maintenance and

Service - Advanced Course

TIA -Programming with TIA Portal -

Basic Course

TIA - Programming with TIA Portal - Advanced Course

Visualisation with WinCC Comfort

TIA -S7 GRAPH Step Sequence Programming

Machine SafetyGuidelines

TIA - S7 Safety Advanced

SIMATIC S7 -Troubleshooting for

Maintenance and Service - Basic Course

SIMATIC S7 -for Programmers

TIA - Transfer course S7 to TIA Portal

SIMATIC S7PLC Commissioning

SIMATIC S7 -GRAPH Step Sequence

Programming

SIMATIC S7 -for Advanced Programmers

SIMATIC S7 -Troubleshooting for

Maintenance and Service - Advanced

Course

Visualisation with HMI WinCC flexible

PROFIBUS

PROFINET

Machine SafetyGuidelines

SIMATIC S7 -Safety Integrated

Drive TechnologyBasics

Drive Technology with SIMOTION and

SINAMICS 120 F

Drive Technology SIMOTION Advanced

Course

Drive Technology

– 7 –

SIMATIC S7 – PLC Commissioning

Target Group You are a commissioning engineer or a service engineer and want to deepen your knowledge of the commissioning PLC programs in plants automated with Siemens S7 assemblies?

Requirements You already know the contents of the QTE training “Siemens S7 PLC – Mainte-nance and Service” or the QTE training “Siemens S7 PLC for Programmers” respectively an equivalent qualification.

Description This training provides you with knowledge about troubleshooting and how to

localize typical plant malfunctions with the aid of the STEP 7 diagnostic function and offers you a practical guideline to the commissioning of PLC programs that are created with the SIMATIC manager.

Training Methods The training contents will be discussed in a multimedia manner. Typical applica-tion examples deepen your theoretical knowledge. There is enough time to apply your newly acquired knowledge practically to S7-300 automation tools and to a simulation model.

• Methodological approach to the commissioning of PLC programs in systems automated with Siemens S7 assemblies

• Commissioning and fault diagnostics in PROFIBUS networks• Common types of interference (e. g. hardware failure, program faults

respectively logical and sporadic faults)• Detecting and troubleshooting of malfunctions• Verification possibilities of the correct functions• Introduction to the STEP 7 diagnostics function• Diagnostic possibilities with organization blocks• Localization of system-specific faults

Duration of the Training 4 days

Minimum Number of Participants 3 persons

– 8 –


SIMATIC S7 – Troubleshooting for Maintenance and Service – Basic Course

Target Group You are a service and maintenance staff member, work with a Siemens S7-300 respectively a S7-400 PLC control and need a profound knowledge in the search of malfunctions to increase the product-specific requirements?

Requirements To participate in this training, you need prior knowledge of Microsoft Windows and digital technology.

Description As member of the maintenance stuff, you often are faced with various tools of

different manufacturers. In addition to the knowledge of existing systems, this training imparts to you a sense of security in handling the applied software. By learning common programming functions you gain well-grounded basic know-ledge for efficient troubleshooting.

Training Methods The training contents will be discussed in a multimedia manner. Typical application examples as well as easy programming exercises strengthen the theoretical knowledge. There is enough time to apply your newly acquired know-ledge practically to S7-300 automation tools.

• Getting to know the hardware components of the SIMATIC S7 family• Working with the software interfaces SIMATIC manager, hardware

configurator, symbol editor, tables of variables and force tables, reference list, LAD / STL / FBD editor

• Composition of S7 programs in FBD and LAD (optional: STL)• Application of symbolic addressing • S7 online / offline modus• Setting Profibus-DB/Profinet links• Entering, reading and interpreting programs• Introduction to functions, function blocks and data blocks• Getting to know arithmetic and conversion functions• Getting to know the error data block functions• Detection and correction of sources of errors with the aid

of a cross-reference list and a diagnostic buffer• Determination and fixing of error sources on a practice model• A short insight into WinCC flexible



Specific Contents

– 9 –

SIMATIC S7 – Troubleshooting for Maintenance and Service – Advanced Course

Target Group You are a service and maintenance staff member and want to gain advanced knowledge of fault localization and troubleshooting in plants automated with Siemens S7 assemblies?

Requirements You already have some knowledge of the contents of the QTE training “Siemens S7 PLC – Maintenance and Service“ respectively an equivalent qualification.

Description This training helps you refresh the knowledge attained in our troubleshooting

basic course and conveys to you a comprehensive guideline for the localization of typical malfunctions of the system with the aid of the STEP 7 diagnostic function as well as the fault diagnosis of S7 assemblies.

Training Methods The training contents will be discussed in a multimedia manner. Typical appli-cation examples deepen this theoretical knowledge. There is enough time to practically apply your newly acquired knowledge to S7-300 automation devices and to a simulation model.

• Refresh of S7 troubleshooting knowledge• Typical types of interference (e. g. hardware fault,

program faults respectively logical and sporadic faults)• Methodical approach to fault diagnostics• Localization of system-specific faults• Programming of fault-recognition programs• Diagnostics possibilities with organization blocks• Detecting and troubleshooting of malfunctions with the help of a practice mo-

del• Application of the STEP 7 diagnostics function• Fault diagnostics in PROFIBUS networks



Specific Contents

– 10 –


SIMATIC S7 – for Programmers

Target Group You are a commissioning engineer, programmer and project engineer and need more detailed knowledge of the programming package SIMATIC S7? Furthermo-re, through this training you wish to lay a sound foundation for other deepening respectively product-specific complementary courses?

Requirements You already have basic knowledge of the contents of programming comparable PLC types as well as knowledge of digital technology? PC and Microsoft Windows skills will be necessary in any case.

Description You will get an overview on functional opportunities of the Siemens SIMATIC S7

PLC family and an insight into structuring, programming, documentation, main-tenance and commissioning of these products.

Training Methods The training contents will be discussed in a multimedia manner. Typical applica-tion examples reinforce this theoretical knowledge. Furthermore, you will have ample opportunity to practically apply your new knowledge to S7-300 automation devices.

• The product categories of the SIMATIC S7 family• Handling of the SIMATIC manager software interface• The principle of structured programming with STEP 7• Communication via Multi-Point Interface (MPI) with global data table• Entering, reading and interpreting of a simple program• Documentation possibilities• Programming and testing of functions, function data and organization blocks• Application of symbolic addressing• Application of the STEP 7 software for the configuration and parameterization

of the CPU and the different cards.• Working with reference list and diagnostic buffer• Arithmetic instructions and conversion functions• Alarm controlled program editing• Networks in the world of SIMATIC S7• Software package S7 PLCSIM for the simulation of PLC programs• Communication PROFINET via the get and put function



Specific Contents

– 11 –

SIMATIC S7 – for Advanced Programmers

Target Group You are a commissioning engineer, programmer or a service and maintenance staff member and need more detailed knowledge of S7 programming?

Requirements You already have taken part in the QTE training “Siemens S7 PLC for Program-mers” or have equivalent knowledge.

Description After attending this course, you will be able to independently recognize and

analyze complex processes in S7 programs and to make modifications to pro-grams, if necessary. Participants will learn as well how to program extended functions independently.

Training Methods The training contents will be debated in multimedia form. For clarification, iconographic programs will be used. The alternation between theory and practi-cal exercises rounds the course off.

• Evaluation of the status word• Jump functions• Accumulator function• Extended mathematical functions• Indirect addressing• Extended data types• Fault analysis• Extended S7 basic communication• Control functions



Specific Contents

– 12 –


SIMATIC S7 – Safety Integrated

Target Group You are a programmer and/or project engineer, commissioning engineer, or maintenance and service staff member and require knowledge about SIMATIC S7 Safety Integrated?

Requirements You already participated in QTE training „SIMATIC S7- Troubleshooting for Mainte-nance and Service – Advanced Course“ or „SIMATIC S7 for Programmers“ or have equivalent qualification.

Description You receive insight on functioning, diagnosis, troubleshooting, programming and

commissioning with Safety Integrated. This training includes the S7-300‘s re-spectively S7-400‘s fail-safe central processor modules as well as the fail-safe decentral ET200 systems.

Training Methods The training contents will be discussed in a multimedia manner. Typical applica-tion examples deepen your theoretical knowledge. You will be given the opportu-nitiy to apply your newly acquired knowledge in practice using S7-300 automation tools and simulation models.

• Overview on standards and guidelines • The principle, system design and periphery of SIMATIC S7 300F • Programming of a safety-related user program• Distributed Safety project planning of a fail-safe periphery• Diagnostic possibilities(CPU diagnosis, periphery diagnosis, further diagnostic

tools)• Communication, troubleshooting for periphery structure• Practical exercises for periphery structure• Examples in programming (programming particularities, Emergency Stop,

safety door, safety-oriented shutdown, passivation)• Identification of possible errors by means of a practice model


Minimum number of Participants 3 persons

Specific Contents

– 13 –

SIMATIC S7 – GRAPH Step Sequence Programming

Target Group You are a programmer, commissioning engineer, project engineer or maintenance and service staff member and like to gain further knowledge on S7?

Requirements You already know the contents of QTE-Training „SIMATIC S7- Troubleshooting for Maintenance and Service – Basic Course“ or „SIMATIC S7 for Programmers“ respectively an equivalent qualification.

Description This training provides you with knowledge in the field of S7 GRAPH. You learn

everything about project planning and the commissioning of sequence cascades..

Training Methods The training contents will be discussed in a multimedia manner. The course is well balanced between theoretical tasks and practical exercises featuring trai-ning models.

• Technological tasks and sequence cascades• Alternative and simultaneous branching• Generating a sequence cascade with S7 Graph• Programming sequence modules• Programming step actions• Programming transitions• Programming monitoring and interlocking • Event-driven actions • Commissioning and test functions



Specific Contents

– 14 –


TIA – Troubleshooting for Maintenance and Service with TIA Portal – Basic Course

Target Group You are a member of the maintenance and servicing personnel, working with a Siemens S7-300 / 400 and S7-1500 PLC, and need an in-depth knowledge for the everyday use or for troubleshooting, to fully meet the product-specific requirements.

Requirements For the participation in this training, you will require prior knowledge of Micro-soft Windows and digital technology.

Description In this course you will be taught the basics which are necessary to work with the Siemens TIA Portal. Using practical examples, you will receive a basic user knowledge, to be able to safely operate this software as a member of the service and maintenance staff.

Training Methods The training contents are discussed in multimedia format. Typical application examples will be used to broaden your theoretical knowledge. You will have an ample opportunity to apply the newly acquired knowledge in practice using the automation devices S7-300 or S7-1500.

• Getting to know hardware components of the SIMATIC S7 family• Working with the software interfaces of the TIA portal• Structure of S7-programs in FBD and LAD (optional: STL)• Application of symbolic addressing• Online / offline modus of the TIA portal• Setting a PROFINET link• Input, reading and interpreting of programs• Introduction with functions, as well as function and data blocks• Detection and removal of error sources with the help of a cross-reference list

and diagnostics buffer• Detecting and troubleshooting of malfunctions with the help of a practice mo-

del• Brief insight into the integrated WinCC Basic or Advanced



Specific Contents

– 15 –

TIA – Troubleshooting for Maintenance and Service with TIA Portal – Advanced Course

Target Group You are an electrician, service technician or maintenance and service staff member and wish to acquire deeper knowledge in the field of fault localization and trouble-shooting with TIA Portal in automated plants?

Requirements Basic S7 knowledge and prior participation in QTE training „TIA troubleshooting for Maintenance and Service - Basic Course“ respectively equivalent qualification.

Description This training is to refresh you prior knowledge from the Basic Course and grand you profound knowledge and skill in fault localization and troubleshooting.

Training Methods The training contents will be discussed in a multimedia manner. Your theoretical knowledge will be broadened through practical examples. Working with simulation models will put your practical skills to test.

• Refreshment of your TIA troubleshooting skills• Typical types of malfunction• Hardware, programming, logical and sporadical types of error)• Methodical approach to troubleshooting• Localizing system-specific malfunctions• Writing fault detection programs• Diagnostic possibilities using organizational blocks• Localizing and resolving malfunctions using a practice modele• Using the STEP 7- diagnostic functions• Fault diagnosis in PROFINET networks



Specific Contents

– 16 –


TIA – Programming with TIA Portal – Basic Course

Target Group You are a design engineer, software engineer or project engineer and wish to gain basic knowledge on programming with TIA portal?

Requirements Basic S7 and TIA portal knowledge is required.

Description You gain insight into the different tools of programming based on TIA portal. Fur-thermore you get to know how to program based upon this structure. This includes Graph Step Sequences as well as STL-programs.

Training Methods Training contents are being discussed in multimedia format. The course is well balanced between theoretical tasks and practical exercises with training models.

• Operating TIA portal‘s software interfaces• Configuration of Siemens CPU 1500 hardware• Connection to Profinet-GSD third party devices• Structured programming with TIA portal• Programming and testing functions, function-, data- and organisation blocks• Programming and interpreting GRAPH step sequences• Programming and interpreting STL programs• Programming complex programs (e.g. error interception circuit with time stamp)• Arithmetical instructions and conversion functions• Working with different data types (INT,REAL,BCD,TOD,DT..) • Alarm controlled program editing• Introduction to S7 PLCSIM S71200/S71500 software package for PLC simulation • Compilation of a Profinet S7 connection



Specific Contents

– 17 –

TIA – Programming with TIA Portal – Advanced Course

Target Group You are a design engineer software engineer or project engineer and wish to gain advanced knowledge on TIA portal based programming?

Requirements Basic S7 knowledge and previous knowledge gained in the QTE training „TIA – Pro-gramming with TIA Portal – Basics“ or comparable qualifications.

Description This training gives insight into the different tools of programming based on TIA por-tal as well as on how to do structured programming with TIA. This includes Graph step sequences as well as STL-programs.

Training Methods Training contents are presented in a multimedia manner. The course is well balan-ced between theoretical tasks and practical exercises on training models.

• Programming and interpreting complex STL programs• Jump functions, accumulator functions, status word analysis)• Working with extended mathematical functions• Indirect adressing and indexed data access• Programming with SCL• Working with extended data types (e.g. STRING) • Error analysis• Extended S7-basic communication• Working with control functions



– 18 –


TIA – Transfer course from SIMATIC S7 to the TIA Portal

Target Group You are a commissioning engineer, programmer and / or design engineer and already using the SIMATIC S7, and you also want to continue to be able to ma-nage your technological advances while at the same time transitioning to the Siemens TIA portal. In addition, you are aiming to create a good foundation for further in-depth or product-specific supplement courses through this training.

Requirements You already possess basic knowledge about programming with SIMATIC S7, as well as knowledge in the field of digital technology. PC and Microsoft Win-dows skills are required in any case.

Description In this course we will teach you the main differences between the SIMATIC S7-300 / 400 and SIMATIC S7-1500, the engineering tools SIMATIC manager and TIA portal, as well as the STEP 7 V5.x and STEP 7 on the basis of the TIA portal. You will learn the project design and advanced programming capabilities of the automation system SIMATIC S7-1500 with the engineering platform TIA portal.

Training Methods The training contents are discussed in multimedia format. Typical application examples will be used to broaden your theoretical knowledge. You will have an ample opportunity to apply the newly acquired knowledge in practice using the automation devices S7-300 or S7-1500.

• Engineering tools TIA portal: SIMATIC STEP 7 and SIMATIC WinCC• Presentation of the SIMATIC S7-1500 hardware• Configuration of devices and networks with the system family SIMATIC S7

using the SIMATIC S7-300 or S7-1500 as an example• Working with the PLC variable table in the TIA portal• Program modules and editor• New possibilities for programming the SIMATIC S7-300 or S7-1500• Troubleshooting with the TIA portal tools and the SIMATIC S7-300 or S7-1500• Presentation of the operating and observation system SIMATIC WinCC• Migration of a SIMATIC STEP 7 V 5.x project to SIMATIC STEP 7

based on the TIA portal• Adaption of a SIMATIC S7-300 / 400 program to the SIMATIC S7-1500



Specific Contents

– 19 –

TIA – Safety Advanced

Target Group You are a programmer and/or prpject engineer, commissioning engineer, main-tenance and service staff member and in need of knowledge on TIA-Step 7 Safety Advanced?

Requirements Previous knowledge about contents of QTE Trainings „TIA - Programming with TIA Portal - Basic Course“ and/or „TIA- Troubleshooting for Maintenance and Service with TIA portal – Advanced Course“ or equivalent qualifications.

Description You gain insight on functionality, diagnosis, troubleshooting, programming and commissioning of TIA-S7 Safety Advanced. This also features fail-safe central-pro-cessor modules of S7-1200 respectively S7-1500 as well as fail-safe decentralized ET200-systems..

Training Methods Training contents are discussed in a multimedia manner. Typical application exa-mples deepen your theoretical knowledge. You get sufficient opportunities to put your newly acquired knowledge to practice with S7-1500 automation devices and a simulation model.

• Overview on standards and guidelines • SIMATIC S7 Safety Advanced principle, system design and periphery • Programming a safety-oriented user program• Distributed Safety project work of the error assured bus• Diagnostic possibilities (CPU-diagnosis, periphery-diagnosis, advanced diagnosic

tools)• Communication, troubleshooting for periphery development• Tasks for periphery development• Programming examples (programming particularities, emergency stop, safety-

oriented shutdown, passivation)• Identifying potential errors with the aid of a practice model.



Specific Contents

– 20 –


TIA – Step Sequence Programming with TIA Portal

Target Group You are a programmer, project engineer, commissioning engineer or maintenance and service staff member and wish to gain knowledge regarding step sequence programming based on TIA portal?

Requirements Previous participation in QTE-Training „TIA- Troubleshooting for Maintenance and Service – Basic Course“ respectively „TIA- Programming with TIA Portal – Basic Course“ or other comparable qualifications.

Description This training communicates knowledge about the planning, programming and com-missioning of sequence cascades based on TIA portal..

Training Methods Training contents will be discussed in a multimedia manner. The course is well balanced between theoretical tasks and practical exercises with training models..

• Technological tasks and sequence cascades• Alternative and simultaneous branching• Generating a sequence cascade based on TIA portal• Programming sequence blocks• Programming step actions• Programming transitions• Programming monitoring and interlocks• Event-driven actions • Commissioning and test functions



Specific Contents

– 21 –

PROFIBUS

Target Group You are an engineer and like to acquire knowledge of the industrial field bus net-work PROFIBUS in order to configure and analyze PROFIBUS networks indepen-dently?

Requirements A general understanding of HMI, PLC and network systems is advandaysous. Microsoft Windows skills are required. In the practical part of the course, Siemens S7 PLC systems will be used. Thus, basic knowledge of the STEP 7 software is necessary as well.

Description During this course, an overview of PROFIBUS will be given: history of origins,

philosophy, various important terms, characteristics and embodiments. Notions like PROFIBUS DP and PROFIBUS FMS will be explained in detail.

Training Methods The training contents are discussed in multimedia format. Illustrative example programs and practical exercises will broaden your theoretical knowledge.

• PROFIBUS as an open field bus system – connection to the ISO / OSI model• Transmission media: physical characteristics, installation details• PROFIBUS protocols: FDL, DP, FMS and PA• Principle of token passing, master-slave and multi-master networks• PROFIBUS addressing• Active respectively passive PROFIBUS partners• Master-master communication via FDL layer• Configuration software: Siemens STEP 7• Use of the BT 200 test device for PROFIBUS and the diagnostic repeater• Commissioning and diagnostic functions by means of the different STEP 7

online functions and in the user program with the CPU interface and communication processor



Specific Contents

– 22 –


PROFINET

Target Group You are a programmer, project manager and commissioning engineer? You wish to get acquainted with PROFINET and its application possibilities in the field of industrial network engineering?

Requirements General experience with the STEP 7 software is required.

Description With the help of SIMATIC NET components, you will learn how to parameterize a PROFINET network, put it into operation and correct malfunctions quickly and effectively. The core point of the training is the planning, installation and configuration of the network in order to avoid errors during designing and commissioning.

Training Methods The training contents will be discussed in multimedia form. For the practical exercises, training models are at your disposal.

• Basics of PROFINET IO with project planning and programming as well as basics of PROFINET RT & IRT

• Installation guide for PROFINET IO networks• PROFINET network components and network transitions• Commissioning of the PROFINET IO network• Diagnose and fault localization of the PROFINET network• Comprehensive practical examples with exercises



Specific Contents

– 23 –

Visualisation with HMI WinCC flexible

Target Group You just begin to work with SIMATIC touch panels (TP) and / or operator panels (OP)? This training is also suitable for you if you do implement, program and design or want to acquire more detailed knowledge of TP and / or OP and wish to develop programs for TP and / or OP using WinCC.

Requirements In this training, basic PC, respectively Windows skills are required. Skills in de-aling with the programming of similar interface devices and knowledge of digital technology would be a plus. We recommend this course to you if you have already taken part in a S7 / STEP 7 training.

Description You will get an overview of the different Siemens TP s respectively OP s and

their possibilities. You will learn how to use WinCC in the fields of programming, documentation, implementation and support.

Training Methods The training contents are discussed in multimedia format. Illustrative example programs and practical exercises will broaden your theoretical knowledge.

• Possible applications of Siemens TP`s respectively OP`s• Communication between TP`s and OP`s and the different PLC processors• Base statements to the tool package, images and variables• General parameters and LED status• Process and malfunction notifications• E / A fields• Recipe processing• Setting and adaptation of communication parameters• Data protection via backup / restore• Optional – for graphics devices – bar and curve charts, dynamization of objects



Specific Contents

– 24 –


Visualisation with WinCC Comfort (TIA Portal)

Target Group You are a programmer, commissioning engineer, project engineer or maintenance and service staff member and you wish to gain further knowledge about HMI-visualization based on TIA-portal?

Requirements TIA portal basic knowledge and previous participation in QTE training „TIA - Trou-bleshooting for Maintenance and Service – Advanced course“ respectively „TIA- Programming with TIA portal –Basic course“ or equivalent qualifications.

Description This training gives you an insight into the new TIA Portal based SIMATIC WinCC

and how to use, understand and operate the program with ease. Furthermore you gain competence in using the software interface which makes it easy to integrate SIMATIC WinCC Comfort into your working routine.

Training Methods Training contents are discussed in a multimedia manner. The course is well ba-lanced between theoretical tasks and practical exercises.

• Configuration of Siemens HMI stations• Communication between HMI stations and different PLC-processors• Basic instructions for the tool package, pictures and variables• Error and process report• Input / output fields• HMI recipe processing• HMI user administration• Setting and adaption of communication parameters• Data protection via backup / restore• Dynamization of objects: curve and bar charts• Exercises with a practice model



Specific Contents

– 25 –

Drive Technology Basics

Target Group You are an electrical or mechanical maintenance employee and interested in gaining basic knowledge on selection, connections and basic functions of drive components?

Requirements Electrical engineering basics are required.

Description This training communicates basic knowledge in operating and connecting diffe-rent drives.

Training Methods Training contents are discussed in a multimedia manner. The course is well ba-lanced between theoretical tasks and practical exercises..

• Differences between drives, three-phase, servo and direct-current motors• Chosing suitable drive systems• Chosing fitting power electronics• Choice and calculation of upstream and downstream fuses, automats and motor

contactors• Advantages and disadvantages of group drives • Connection of power electronics to control systems• Connection via bus systems, cables, analog and digital signals• Feedback of actual signals to power electronics and PLC• Adjusting torques, currents and platforms• Controls and control programs for positioning drives• Safety shut-down for drives



Specific Contents

– 26 –


Drive technology with SIMOTION and SINAMICS 120F

Target Group You are an electrical or mechanical maintenance employee or control technician and interested in gaining knowledge on using SIMOTION drive technology?

Requirements Basic knowledge of electrical engineering and automation is required.

Description In this training you will be taught the principles of configuration, parameterization and commissioning of a motion control system. Furthermore you learn to pro-gram simple functions which you will operate during the exercises.

Training Methods Training contents are presented in a multimedia manner. The course is well ba-lanced between theoretical tasks and practical exercises.

• Drive technology basics• Differences between inverter technology and motion control• Component overview motion control• Hardware structure• Project planning regarding axis and drives• Developing simple application programs• Commissioning axes• Optimization and parameterizing of actions and axes • Runtime system configuration• Fault detection and diagnosis• Troubleshooting• Quick data exchange through visualization



Specific Contents

– 27 –

Commissioning, Parameterization and Communication of Converters

Target Group You are an electrical or mechanical maintenance employee respectively control technician and interested in acquiring knowledge on handling converters?

Requirements Basic knowledge of drive technology and automation is required.

Description This training teaches you to commission converters and drive systems, to pa-rameterize converter and to set up the communication via Profibus respectively Profinet. Singular and important functions and adjustment options are described in a step by step approach. Through this you learn the correct IBN and paramete-rization of the converter including data exchange with a higher level controls for safe and reliable facility operation.

Training Methods Training contents are examined in a multimedia manner. The course is well ba-lanced between theoretical tasks and practical exercises.

• Structure and function of the converter• Installation of the communication via Profibus/ Profinet• Parameterization of important functions• Commissioning the converter• Transmission of set- and actual values• Setting and editing control functions• Converter diagnosis and troubleshooting



Specific Contents

– 28 –


Machine Safety Guidelines

Target Group You are an electrical or mechanical maintenance employee or control engineer and in need of instruction about the standard requirements regarding machine safety?

Requirements Basic knowledge of electrical engineering is required.

Description This training is specifically targeted to maintenance staff members who need an instruction on safety technology and standards for modifying plants and equip-ment.

Training Methods Training contents are examined in a multimedia manner. The course is well ba-lanced between theoretical tasks and practical exercises.

• Safety technology basics• Safety regulations and norms• Conformity assessment procedure• Risk analysis• Inspection and acceptance of electrical safety measures according to IEC/EN

60204 1 (electrical safety of machines and systems)• Machine directives and CE-labelling



Specific Contents

QTE Trainings BECKHOFF

– 29 –

BECKHOFF TwinCAT

Maintenance and Service with

BECKHOFF TwinCAT 2

BECKHOFF Transfer Course from TwinCAT 2

to TwinCAT 3

Maintenance and Service with

BECKHOFF TwinCAT 3

BECKHOFF Product Trainings

Your benefitsWith the BECKHOFF TwinCAT system you can use almost every compatible Windows PC for controlling your plant or machine in realtime.During this, control programs and development environments are used for programming, diagnostics and configu-ration. All Windows programs can use the TwinCAT data through Microsoft interfaces and run commands.

QTE Trainings BECKHOFF

– 30 –


Maintenance and Service with BECKHOFF TwinCAT 2

Target Group You are a maintenance and service employee and you wish to gain knowledge of the functionalities of Beckhoff TwinCat 2 controllers to localize and resolve mal-functions efficiently?

Requirements Sound knowledge in Microsoft Windows and digital technology is required.

Description As a maintenance and service employee you are usually confronted with various devices by different manufacturers. This training deepens your knowledge in ope-rating the Beckhoff hard- and software interface combined with prior knowledge on pre-existing installations. Through teaching common SPS-program functions solid basic knowledge of efficient troubleshooting are passed to the participants.

Training Methods Training contents are discussed in a multimedia manner. Typical application examples and simple programming tasks deepen your theoretical knowledge. The course is well balanced between theoretical tasks and practical exercises. You will be provided with sufficient opportunities to practice the newly acquired knowledge with Beckhoff TwinCAT 2

• Working with the Beckhoff TwinCAT IEC 61131 3 software interface• Creation and expansion of input and output variables in IEC 61131 3 • Connecting system manager with field bus• Standard and user defined data type variables• TwinCAT-system programming basics• Program extension and analysis• System function application • TwinCAT 2 documentation and management functions • Source code storage on PLC-lifetime• CX 1000 remote operation• Basic settings for PC CX communication



Specific Contents

– 31 –

BECKHOFF transfer course from TwinCAT 2 to TwinCAT 3

Target Group You are a maintenance and service employee or commissioner work with Beck-hoff products and want to gain furter knowledge on technological changes and wish to switch to Beckhoff TwinCAT 3?

Requirements Sound knowledge of Beckhoff IEC 61131 3, Microsoft Windows and general compu-ter skills are required.

Description This course focusses on the main distinctive features of Beckhoff IEC 61131 3 and Beckhoff eXtended Automation (XA) as well as project planning and extended programming possibilities of the Beckhoff TwinCAT 3 engineering platform..

Training Methods Training contents are discussed in a multimedia manner. Typical application ex-amples and simple programming tasks deepen your theoretical knowledge. The course is well balanced between theoretical tasks and practical exercises. You will be provided sufficient opportunity to train the newly acquired knowledge.

• Engineering tools Beckhoff eXtended Automation (XA) • Introduction to TwinCAT 3 system • Device and network configuration• Working with the global variables list• Program modules and editor• Troubleshooting with Beckhoff eXtended Automation (XA)• Presentation of the operation and observation system• Diagnosis and handling possibilities in Beckhoff eXtended Automation (XA)



– 32 –


Maintenance and Service with BECKHOFF TwinCAT3

Target Group You are a maintenance and service staff member and interested in gaining know-ledge on the practicalities of the BECKHOFF TwinCAT3 controller to localize and resolve faults efficiently?

Requirements Sound knowledge of Microsoft Windows and digital technology are required.

Description As a maintenance and service employee you are usually confronted with various devices by different manufacturers. This training deepens your knowledge on in operating the BECKHOFF hard- and software interface combined with prior knowledge on pre-existing installations. Through teaching common PLC-pro-gram functions solid basic knowledge about efficient troubleshooting is passed to the participants.

Training Methods Training contents are discussed in a multimedia manner. Typical application examples and simple programming tasks deepen your theoretical knowledge. The course is well balanced between theoretical tasks and practical exercises. You will be provided with sufficient opportunities to practice the newly acquired knowledge with Beckhoff TwinCAT3.

• Introduction to Beckhoff eXtended Automation (XA) • TwinCAT 3 system architecture• Overview and structure of hardware components• Configuration and connection to a bus terminal• Creation of a PLC program• Creation of global variables, data types (DUT), variable data types• Introduction to function modules in SPS (PRG, FB, FUN) • Introduction to IEC 61131 3 • Exercises, diagnostic possibilities, troubleshooting• Creation of PLC boot projects• Diagnosis with TwinCAT 3 Measurement (Scope) • Introduction to TwinCAT PTP axis positioning system• Calibration and setup of axis in system manager • Step sequence programming PLC to system manager for axis and variables


Minimum Number of Participantsl 3 persons

Specific Contents

– 33 –

Allgemeine Geschäftsbedingungen QTE Trainings

1. Geltungsbereich:Sämtliche Trainings laut QTE-Trainings-Katalog und individuell vereinbar-te Trainings der QTE GmbH erfolgen ausschließlich zu den Allgemeinen Ge-schäftsbedingungen. Davon abweichende Bedingungen mit dem Kunden gelten nur mit der ausdrücklichen Zustimmung der QTE GmbH.2. Leistungsumfang:Der Leistungsumfang der Trainings beinhaltet die Abhaltung der jeweiligen Trainings am vereinbarten Ort, die Bereitstellung der Hardware, Trainingsun-terlagen und eine Teilnahmebestätigung. Die Description der Trainingsinhalte entspricht dem Standard des Kataloges der QTE GmbH zum Zeitpunkt der Aus-gabe des Kataloges. Inhaltliche Änderungen oder Anpassungen während des Trainings behält sich die QTE GmbH ausdrücklich vor. Für individuell auf den Kunden abgestimmte Trainings ist der jeweilige Leistungsumfang entspre-chend zu definieren. Ein Anspruch auf eine Teilnahmebestätigung besteht bei einer Teilnahme von mehr als 80 % des für das Training festgesetzten Zeit-raumes. Der Kunde garantiert, dass der Leistungsumfang ausschließlich zum unmittelbaren Zwecke des Kunden und nicht für Dritte verwendet wird, soweit hier schriftlich keine andere Vereinbarung getroffen wurde.3. Anmeldung, Datenverarbeitung:Anmeldungen erfolgen schriftlich unter Verwendung des Anmeldeformulars auf der Website oder nach schriftlicher Beauftragung. Der Kunde erhält nach Auftragseingang eine Auftragsbestätigung über das bestellte Training, den Ort, Termin und den Preis. Der Kunde erteilt des Weiteren seine Zustimmung , dass die in der Anmeldung enthaltenen personenbezogenen Daten seitens der QTE GmbH gespeichert und verarbeitet werden dürfen.4. Preise und Zahlungsbedingungen:Die Preise für die Trainings sind im Kataloganhang – aktueller Stand- aufge-führt bzw. für individuelle Trainings zu vereinbaren. Grundsätzlich erhält der Kunde vorab ein entsprechendes Angebot. Aufenthalts,- Übernachtungs- und Reisekosten sind (soweit im Angebot nicht anders vereinbart) vom Kunden zu tragen. Die Preise verstehen sich, soweit nicht anders vereinbart, in Euro ex-klusive Umsatzsteuer und sonstiger Gebühren oder Spesen und sind freiblei-bend. Der Kunde erhält nach Anmeldung eine Rechnung, die innerhalb von 14 days ab Fakturadatum, netto, spesen-und abzugsfrei zahlbar ist, spätestens jedoch zum Trainingsbeginn.5. Stornierung:Der Kunde hat das Recht, vor dem Trainingsbeginn Ersatzteilnehmer/innen zu benennen, soweit von der QTE GmbH keine begründeten Einwände bestehen. Für vereinbarte, aber nicht in Anspruch genommene Trainings verrechnet die QTE GmbH wie folgt:Eine schriftliche Stornierung bis 4 Wochen vor Schulungsbeginn ist kostenfrei. Bei Absage bis 3 Wochen vor Schulungsbeginn werden 50% und bei Absage bis 2 Wochen vor Schulungsbeginn 70% der Kursgebühren erhoben. Nach Ablauf einer Frist von bis zu 2 Wochen ist die Kursgebühr in voller Höhe zu entrichten. Sollte ein Teilnehmer durch Krankheit, oder vergleichsweise schwerwiegenden Gründen an der Teilnahme gehindert sein und ist eine kostenlose Absage nicht mehr möglich, kann die QTE GmbH einen Gutschein ausstellen, der zur Teilnah-me an einem späteren, von der QTE GmbH festgelegtem Zeitpunkt berechtigt.6. Änderungsvorbehalt:Die QTE GmbH behält sich das Recht vor, angekündigte bzw. vereinbarte Trai-nings örtlich und/oder zeitlich zu verlegen, wenn es sachliche oder rechtlich gerechtfertigte Gründe nötig machen (z.B. bei zu geringer Teilnehmeranzahl, Erkrankung des Trainers, nationale oder internationale Vorschriften, Sank-tionen oder ähnliches) oder den Trainer auszutauschen. Im Falle einer gänz-lichen Absage werden die bezahlten Preise zurückerstattet. Bei Änderung von

Zeit bzw. Ort hat der Kunde das Recht, innerhalb von 3 Kalenderdaysn nach Zugang der Änderungsnachricht schriftlich und kostenfrei zu stornieren. An-sonsten gilt die Änderung nach den neuen Bedingungen als vereinbart. Der Kunde verzichtet auf Ansprüche wegen vergeblicher Aufwendungen oder son-stige Schadens- und Aufwandsansprüche geltend zu machen. 7. Sicherheitsvorschriften:Der Teilnehmer verpflichtet sich, geltende Sicherheits,- Unfallverhütungs-, Ordnungsbestimmungen sowie Anweisungen und besondere Zugangsrege-lungen auf dem Gelände der QTE GmbH einzuhalten.8. Haftung:Sowohl in den Trainingsunterlagen als auch während des Trainings werden technische Informationen durch die QTE GmbH nach bestem Wissen und Ge-wissen vermittelt. Die QTE GmbH garantiert aber nicht, dass diese Informati-onen stets fehlerfrei sind. Für den Kunden im Rahmen möglicher zugefügter Schäden haftet die QTE GmbH im Rahmen ihrer Betriebshaftpflichtversiche-rung, insgesamt bis zum Nettobetrag des Trainingspreises. Weiterhin haftet die QTE GmbH für Schäden bei Vorsatz bzw. grober Fahrlässigkeit. Die Haftung für leichte Fahrlässigkeit, der Ersatz von Folgeschäden, reine Vermögensschä-den, entgangenem Gewinn und Schäden aus Ansprüchen gegenüber Dritten gegen den Kunden sind ausgeschlossen, ebenso eine Haftung für den Trai-ningserfolg. Bei Beschädigung von Datenträgermaterial des Kunden umfasst die Ersatzpflicht nicht den Aufwand für die Wiederbeschaffung verloren gegan-gener Daten. Weitergehende Schadensersatzansprüche , gleich aus welchem Rechtsgrund, sind ausgeschlossen. Soweit die Training in Räumlichkeiten und Gelände des Kunden stattfinden, haftet die QTE GmbH nicht bei Unfällen, Ver-lust oder Beschädigung des Kundeneigentums, es sei denn, der Schaden wurde vorsätzlich und grob fahrlässig verursacht.9. Copyright, Urheberschutz und Geheimhaltung:Alle von der QTE GmbH bereitgestellten Unterlagen sind als geistiges Eigentum schützenswertes Know-How der QTE GmbH und/oder Dritten. Eine Weitergabe oder Vervielfältigung ist ohne ausdrückliche Genehmigung von der QTE GmbH nicht gestattet. Die von der QTE GmbH zum Zweck des Trainings bereit gestellte Software darf weder entnommen, noch ganz oder teilweise kopiert werden. Der Kunde haftet für jedes Zuwiderhandeln.10. Sonstige Bestimmungen:Sollten einzelne Bestimmungen ganz oder teilweise unwirksam und/oder un-durchsetzbar sein oder werden, so bleiben alle übrigen Bestimmungen wirk-sam. Das gleiche gilt für entsprechende, nicht genannten Regelungslücken.11. Anzuwendendes Recht/Gerichtsstand:Gerichtsstand für alle Rechtstreitigkeiten, die sich aus dem Vertragsverhältnis ergeben oder in diesem Zusammenhang stehen, ist für den Kunden ausschließ-lich das sachlich für die QTE GmbH zuständige Gericht in Kassel. Die QTE GmbH ist jedoch berechtigt, an jedem anderen Gericht zu klagen, das nach nationalem oder internationalem Recht zuständig sein kann. Auf sämtliche, insbesondere diesen Trainingsbedingungen zugrunde liegenden Rechtsgeschäften ist aus-schließlich deutsches Recht anzuwenden. Ausgenommen sind Verweisungs-normen, insbesondere jene des internationalem Privatrechts, soweit diese auf die Anwendung des ausländischen Rechts verweisen. Sieht das deutsche Recht bei Auslandsberührung die Anwendung spezieller, auch in Deutschland geltender internationaler Sachnormen- wie z.B. das UN-Kaufrecht- vor, so sind diese nicht anzuwenden.

Stand: 01.02.2016

– 34 –


What our satisfied customers are saying about us:

Further information on our satisfied customers can be provided on request.

“The training through the QTE was an absolute benefit for my employees.”

“Every question was answered, and every task was solved.”

“The training was very practice-oriented.”

„ “ Highly effective. Due to the small groups, my questions could be discussed individually.”

“The training was 100 % satisfying.”

“I was able to attain more knowledge than I expected.”

– 35 –

Contact Us

QTE GmbHWarburger Straße 45D-34246 Vellmar

Fon.: +49 (0)561 50614210Fax: +49 (0)561 50614239E-Mail: [email protected]

your contact partnerBettina Jacobi

[email protected]

V 7.0

QTE GmbHWarburger Straße 45D-34246 VellmarGermany

Fon: +49 (0) 561.50 61 42-10Fax: +49 (0) 561.50 61 42-39

[email protected]

welcome to qte training center! - cls energy · 29 beckhoff transfer course from twincat 2 to...

Documents