welcome to our knowledge base - tandisrayan.cotandisrayan.co/files/quick guide dlb 5.pdf ·...
TRANSCRIPT
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 1/13
WELCOME TO OUR KNOWLEDGE BASE
Get Your answer faster! Enter keywords here. SEARCH
/ LigoDLB series / LigoDLB Configuration Scenarios
LigoDLB Configuration Scenarios
– Point to Point (PTP)
Follow the steps to create a simple Point to Point link between Access PointiPoll2 and Station (WDS/iPoll2):
Step 1. Access Point iPoll 2 configuration: change device’s default IPaddress (can be static or dynamic), enable IP alias (Secondary IP) ifnecessary:
It is recommended to use iPoll 2 protocol for simple Point to Pointnetwork configuration.
LigoPTP series
LigoDLB series
NFT series
APC series
Tools
Legacy Products
Legacy Tools
Frequently AskedQuestions
Video on Youtube
ONLINE LigoWaveHelpdesk
Categories
LigoWave News
WNMS mobile
LigoPTP UNITYintroduction
LigoPTP 620HPintroduction
/Home FAQ
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 2/13
Step 2. Configure wireless settings for Access Point iPoll 2:
– Select wireless mode: Access Point iPoll– Set channel: Autoall other settings should be left default:
– Define SSID– Enable Security for secure traffic on linkall other settings should be left default:
Enter the following button in Wireless settings (AP) section tochange SSID and Encryption configuration
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 3/13
Step 3. Station iPoll 2 configuration: change device’s default IP address(can be static or dynamic), enable IP alias (Secondary IP) if necessary:
Step 4. Configure wireless settings for Station iPoll 2:
– Select wireless mode: Station (WDS/iPoll 2)all other settings should be left default:
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 4/13
– Define SSID, or use “Scan” button to find iPoll 2 Access Pointsautomatically– Enable Security for secure traffic on linkall other settings should be left default:
Step 5. It is highly recommended to change default administrator’s
Enter the following button in Wireless settings (station) section tochange SSID and Encryption configuration
Note that Station iPoll 2 security settings must conform thesettings configured on the Access Point iPoll 2 that station isassociated with.
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 5/13
password for each unit:
Step 6. Verify the PTP link connection. Navigate to the Status |Information page. The Information page will display wireless information ofthe link.
The status page of the Access Point iPoll 2 must indicate that onepeer (Station iPoll 2) is connected and information about connectionmust be displayed as follows:
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 6/13
Detailed information about connected peers stays at Status | Wirelesspage.
The status of the Station iPoll 2 must be displayed as Connected andprogress bars indicating the quality of the connection must bedisplayed:
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 7/13
– Point to Multipoint (PTMP)
Point to Multipoint bridged network configuration
In a bridged (layer 2) network could be used in WDS or ipoll 2 modes. Ipoll2 mode should be used when AP and all stations are Deliberant productsotherwise select WDS mode. Recommended maximum stations per AP canbe from 60 to 70.
WDS mode Configuration
Change device’s IP address (can be static or dynamic), enable IP alias(Secondary IP) if necessary. Default ip address could be left because it isused for device management.Configure wireless settings for 11N AP:
– Select wireless mode: Access point (auto WDS)– Choose IEEE mode:N if you use 802.11n capable radiosA/N mixed or B/G/N mixed if you also use legacy radios inyour network– Set channel to “Auto”– Set ACK timeout based on the maximum distance fromthe station, using the slide:
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 8/13
– Define SSID
– Enable Security if necessary
iPoll 2 mode Configuration
Configure wireless settings for iPoll 2 master:
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 9/13
– Select wireless mode: Access Point iPoll– Define SSID– Set channel to “Auto”– Enable Security if necessaryall other settings should be kept default:
Configuration of the stations:
Change device’s IP address (can be static or dynamic). Enable IP alias(Secondary IP) if necessary. All stations ip addresses should be in the samesubnet as AP is.
Change second device’s IP address (can be static or dynamic). Enable IPalias (Secondary IP) if necessary.
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 10/13
Station Wireless section configuration steps:According to access point:
Select country code
Select wireless mode: Station (WDS/iPoll 2)
Set Max data rate N to “Auto”Set ACK timeout based on max distance from the stationLeave all other settings as default
Enable Security if necessaryDefine SSID
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 11/13
Observe with indicator at Access point that all Stations are connected.
Observe signal levels at Access point and at Station. Recommended signallevel range is from 35 to 60 dBm.
If the device is MIMO, there are two signal streams. One of them is calledas “Main” (Antenna 1), another is “Aux”
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 12/13
+
+
+
+
+
+
Main stream is mandatory. If main signal is very weak, the link will not bestable or will not work at all. It is necessary, to align the antennas for thebest main signal. If Aux stream is weak, the link will work at lower data rate.Check if CCQ is good on AP and Station and it is approaching to 100/100.
Step 6. For the best performance, optimize the channel size.
Wireless Access Control List (WACL) Configuration
Management and Data VLAN configuration
Setup CPE as a Router
PPPoE Configuration
HotSpot / Repeater
Repeater Configuration
Before changing auto channel to some particular channel it isrecommended to do the scan on AP and on Station (Tools|Sitesurvey). Try to find the clearest frequency for device operation.
11/27/2015 LigoDLB Configuration Scenarios LigoWave knowledge base
https://www.ligowave.com/wiki/ligodlbconfigurationscenarios/#hotspot 13/13
LigoDLB Firmware Release Notes LigoDLB Product Selection
LigoDLB InstalationRecommendations
LigoDLB Documentation
LigoDLB Declarations of Conformity
Related Articles
The highly acclaimed LigoWave support team is alwaysready to help you solve all arising problems or giveprofessional advice about your network design,deployment, or configuration using LigoWaveequipment.
Support telephone numbers:EMEA support office: +370 37 211705
USA support office:tel. +1 877 544 6928or +1 877 LIGOWAVE
Online LigoWave Helpdesk
LigoWave Support Applications
WNMS
WNMS Cloud
WNMS Mobile
SWEAP
Reset tool
LinkCalc
© Copyright, LigoWave