€¦ · web viewsulfuric acid, 30 percent: no effect. thickness: 3/16 to 1/4 inch (5 to 6 mm)....

SECTION 09 67 23RESINOUS FLOORING AND COATINGS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2019 - 2019 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Decorative Resinous Flooring:1.1.1.1 Troweled epoxy resin. (Cheminert CFS)1.1.1.2 Decorative flake polymeric floor coating. (Colorflake L)1.1.1.3 Decorative colored flake flooring and waterproof membrane. (Elastaflake RFS)1.1.1.4 Troweled epoxy mosaic composition. (Cheminert Terracolor)1.1.1.5 Polymerized cementitious coating. (Resistite Micro Topping)1.1.1.6 Metallic and pearlescent color system. (Metallic Luster)1.1.1.7 Decorative Quartz Epoxy Flooring. (Decor-Flor)1.1.1.8 Decorative Colored Quartz Troweled Epoxy Flooring. (Troweled Decor-Flor)

1.1.2 Urethane Concrete Flooring.1.1.2.1 Troweled urethane cement composition flooring. (Tek-Crete TT)1.1.2.2 Slurryed urethane cement composition flooring. (Tek-Crete SL)1.1.2.3 Troweled urethane cement composition flooring with slip resistant broadcast.

(Tek-Crete SL-B)1.1.2.4 Troweled urethane cement composition flooring with decorative color flake

broadcast. (Tek-Crete SL-CF)1.1.2.5 Troweled urethane cement composition with decorative color quartz broadcast.

(Tek-Crete SL-CQ)1.1.2.6 UV stable polyurethane composition sealer. (Tek-Crete Sealer CP)1.1.2.7 Skim coat. (Tek-Crete Skim Coat)

1.1.3 Epoxy Flooring and Coatings.1.1.3.1 Troweled epoxy resin high-density flooring. (Cheminert HD)1.1.3.2 Troweled epoxy high density flooring. (Cheminert K)1.1.3.3 Conductive, troweled epoxy flooring. (Conductive Cheminert K)1.1.3.4 Self-leveling seamless epoxy flooring. (Cheminert L)1.1.3.5 Electro-static dissipative, self-leveling epoxy resin composition flooring. (Electro-

Flor ESD)1.1.3.6 Conductive, Thin Film Polyurethane Resin Composition Flooring.. (Electro-Flor

CD)1.1.3.7 Conductive, fluid applied, monolithic, high solids epoxy flooring. (Electro-Flor HS

CD)1.1.3.8 Slip-retardant epoxy coating. (Posi-Tred O)1.1.3.9 Chemical, heat and skid resistant epoxy coating. (Posi-Tred CR)

1.1.4 Polyaspartic and Urethane Coatings.1.1.4.1 Pigmented urethane coating. (Aero-Flor 100 Pigmented)1.1.4.2 Clear gloss urethane coating. (Aero-Flor 100 Clear Gloss)1.1.4.3 High-performance polyurethane topcoat. (HPT)1.1.4.4 Polymeric floor coating. (Quik-Glaze)

09 67 23 -1

1.1.4.5 Clear fast-cure coating and topcoat. (Quik-Glaze FC)

1.1.5 Overhead, Patching, and Underlayment Systems.1.1.5.1 Trowel applied polyacrylate resin composition underlayment. (A-81)1.1.5.2 Squeegee applied smoothing and resurfacing compound for concrete. (A-81 SQ)1.1.5.3 Cementitious mortar. (High Strength Mortar)1.1.5.4 Acoustical flooring underlayment. (Acousti-Fill)1.1.5.5 Polymeric concrete admixture. (Contex)1.1.5.6 Flexible polymer modified cementitious repair mortar and underlayment. (G-26)1.1.5.7 Polymerized cementitious self-leveling underlayment. (SLU-50)

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete (03 30 00) - Cast-in-Place Concrete.

1.2.2 Section 03 54 00 - Cast Underlayment (03 54 00) - Cementitious Flooring Underlayment.

1.2.3 Section - (03 01 30) - Concrete Patching and Resurfacing.

1.2.4 Section 07 14 00 - Fluid-Applied Waterproofing (07 14 00) - Fluid-Applied Waterproofing.

1.2.5 Section 07 27 19 - Plastic Sheet Air Barriers (07 26 00) - Vapor Resistive Barriers.

1.2.6 Section 09 61 36 - Static-Resistant Flooring Treatment (09 61 00) - Vapor Control for Flooring.

1.2.7 Section - (09 77 30) - Sanitary Wall Finishes.

1.2.8 Section 22 40 00 - Plumbing Fixtures (22 40 00) - Plumbing Fixtures and Equipment.

1.3 REFERENCES

1.3.1 American Standard Test Method International (ASTM):1.3.1.1 ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus.1.3.1.2 ASTM C109 - Standard Test Method for Compressive Strength of Hydraulic

Cement Mortars (Using 2-in. or (50-mm) Cube Specimens).1.3.1.3 ASTM C307 - Standard Test Method for Tensile Strength of Chemical-Resistant

Mortar, Grouts, and Monolithic Surfacings.1.3.1.4 ASTM C531 - Standard Test Method for Linear Shrinkage and Coefficient of

Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.

1.3.1.5 ASTM C579 - Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.

1.3.1.6 ASTM C580 - Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes.

1.3.1.7 ASTM C672 - Standard Test Method for Scaling Resistance of Concrete Surfaces Exposed to Deicing Chemicals.

1.3.1.8 ASTM C882 - Standard Test Method for Bond Strength of Epoxy-Resin Systems Used with Concrete by Slant Shear.

1.3.1.9 ASTM D412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension.

1.3.1.10 ASTM D522 - Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings.

1.3.1.11 ASTM D523 - Standard Test Method for Specular Gloss.1.3.1.12 ASTM D635 - Standard Test Method for Rate of Burning and/or Extent and Time

of Burning of Plastics in a Horizontal Position.

09 67 23 -2

1.3.1.13 ASTM D638 - Standard Test Method for Tensile Properties of Plastics.1.3.1.14 ASTM D695 - Standard Test Method for Compressive Properties of Rigid

Plastics.1.3.1.15 ASTM D882 - Standard Test Method for Tensile Properties of Thin Plastic

Sheeting.1.3.1.16 ASTM D1044 - Standard Test Method for Resistance of Transparent Plastics to

Surface Abrasion.1.3.1.17 ASTM D1211 - Standard Test Method for Temperature-Change Resistance of

Clear Nitrocellulose Lacquer Films Applied to Wood.1.3.1.18 ASTM D1308 - Standard Test Method for Effect of Household Chemicals on

Clear and Pigmented Organic Finishes.1.3.1.19 ASTM D1737 - Standard Test Method for Elongation of Attached Organic

Coatings with Cylindrical Mandrel Apparatus.1.3.1.20 ASTM D2047 - Standard Test Method for Static Coefficient of Friction of Polish-

Coated Flooring Surfaces as Measured by the James Machine.1.3.1.21 ASTM D2240 - Standard Test Method for Rubber Property-Durometer Hardness.1.3.1.22 ASTM D2370 - Standard Test Method for Tensile Properties of Organic

Coatings.1.3.1.23 ASTM D2794 - Standard Test Method for Resistance of Organic Coatings to the

Effects of Rapid Deformation (Impact).1.3.1.24 ASTM D3359 - Standard Test Method for Rating Adhesion by Tape Test.1.3.1.25 ASTM D3363 - Standard Test Method for Film Hardness by Pencil Test.1.3.1.26 ASTM D4060 - Standard Test Method for Abrasion Resistance of Organic

Coatings by the Taber Abraser.1.3.1.27 ASDTM D4541 - Standard Test Method for Pull-Off Strength of Coatings Using

Portable Adhesion Testers.1.3.1.28 ASTM E84 - Standard Test Method for Surface Burning Characteristics of

Building Materials.1.3.1.29 ASTM E96 - Standard Test Methods for Water Vapor Transmission of Materials.1.3.1.30 ASTM E162 - Standard Test Method for Surface Flammability of Materials Using

a Radiant Heat Energy Source.1.3.1.31 ASTM E648 - Standard Test Method for Critical Radiant Flux of Floor-Covering

Systems Using a Radiant Heat Energy Source.1.3.1.32 ASTM F150 - Standard Test Method for Electrical Resistance of Conductive and

Static Dissipative Resilient Flooring.1.3.1.33 ASTM F609 - Standard Test Method for Using a Horizontal Pull Slipmeter (HPS).1.3.1.34 ASTM F1679 - Standard Test Method for Using a Variable Incidence Tribometer

(VIT).1.3.1.35 ASTM F1869 - Standard Test Method for Measuring Moisture Vapor Emission

Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.1.3.1.36 ASTM F2170 - Standard Test Method for Determining Relative Humidity in

Concrete Floor Slabs Using in situ Probes11.3.1.37 ASTM G21 - Standard Practice for Determining Resistance of Synthetic

Polymeric Materials to Fungi.

1.3.2 American Concrete Institute (ACI):1.3.2.1 ACI 503.1 - Standard Specification for Bonding Hardened Concrete, Steel,

Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive.

1.3.2.2 ACI 503.R - Use of Epoxy Compounds with Concrete.

1.3.3 American National Standards Institute (ANSI):1.3.3.1 ANSI A1264 - American National Standard for the Provision of Slip Resistance

on Walking/Working Surfaces.1.3.3.2 ANSI/ESD S 6.1 - For The Protection of Electrostatic Discharge Susceptible

Items - Grounding.

09 67 23 -3

1.3.4 International Concrete Repair Institute (ICRI):1.3.4.1 ICRI - 310.25 Selecting and Specifying Concrete Surface Preparation.

1.3.5 National fire Protection Association (NFPA):1.3.5.1 NFPA 56A - Standard for the Use of Inhalation Anesthetics.

1.3.6 Society of Protective Coatings (SSPC):1.3.6.1 SSPC - Monitoring and Controlling Ambient Condition During Coating

operations.1.3.6.2 SSPC TU-10 - Procedures For Applying Thick Film Coatings and Surfacings

Over Concrete Floors.1.3.6.3 SSPC TR-5 - Design, Installation, and Maintenance of Protective Polymer

Flooring Systems for Concrete.1.3.6.4 SSPC TECHNOLOGY GUIDE NO. 10 - Guide to Specifying Coatings

Conforming to Volatile Organic Compound (VOC) Content Requirements.1.3.6.5 SSPC-SP 13/NACE No. 6 - Surface Preparation of Concrete.

1.3.7 United States Defense Standard (MIL):1.3.7.1 MIL-D-3134 - Deck Covering Materials.1.3.7.2 MIL-PRF-3135 - Performance Specification: Deck Covering Underlay Materials.1.3.7.3 Typical installation methods.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data:1.4.2.1 Manufacturer's data sheets on each product to be used.1.4.2.2 Preparation instructions and recommendations.1.4.2.3 Storage and handling requirements and recommendations.

1.4.3 Verification Samples: For products specified, two samples, 6 inches (150 mm) square representing actual product, color, Texture and patterns.

1.4.4 Shop Drawings: Details of materials, construction and finish. Include relationship with adjacent construction.

1.4.5 Contractor Certification: Manufacturer letter certifying installer is properly trained in application of materials being installed, and is acceptable to materials manufacturer.

1.4.6 Certification: CA Department of Public Health 01350 Method for Testing and Evaluation of Volatile Organic Chemical Emissions From Indoor Sources Using Environmental Chambers.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with ISO certification and a minimum ten years documented experience.

1.5.2 Installer Qualifications: Specializes in installations to that required for Project with five years' experience. Engage an SSPC Concrete Coatings Inspector certified to perform inspections on Project. Installer will be acceptable to materials manufacturer.

1.5.3 Source Limitations: Each product type from single manufacturer ensuring uniformity.

1.5.4 Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.1.5.4.1 Intent of mock-up is to demonstrate quality of workmanship and visual

09 67 23 -4

appearance.1.5.4.2 If mock-up is not acceptable, rebuild mock-up until satisfactory results are

achieved.1.5.4.3 Retain mock-up during construction as standard for comparison with completed

work.1.5.4.4 Do not alter or remove mock-up until work is completed or removal is authorized.

1.6 PRE-INSTALLATION CONFERENCE

1.6.1 Pre-installation Meetings: Coordinate work of this Section, with related work.1.6.1.1 Attendance: Subcontractor performing work and manufacturers and fabricators

involved, or affected by, installation. Coordinate installations that precede or follow.

1.6.1.2 Agenda: Review progress of construction activities and preparations for the particular activity under consideration. Agenda shall include schedule, drain and floor sink interface, detailing, door thresholds, responsibilities, critical path items, and approvals.

1.6.1.3 Record, agreements, and disagreements, and corrective measures and actions.1.6.1.4 Reporting: Distribute minutes to each party present and others requiring

information.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Deliver materials in original packages and containers with unbroken seals and bearing manufacturer's labels with date of manufacture and production lot number. Store and handle in strict compliance with manufacturer's written instructions and recommendations.

1.7.2 Protect from damage due to weather, excessive temperature, and construction operations.

1.7.3 When practical stage materials in area of Work 48 hours prior to beginning of Work.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, surface temperature, material temperature and ventilation) within limits recommended by manufacturer during installation and cure. Do not install under conditions outside manufacturer's recommended limits.

1.8.2 Restrict access to Work area except installing contractor and site supervision during preparation, installation and cure period.

1.8.3 Lighting: Permanent lighting shall be in place prior to flooring installation.

1.9 WARRANTY

1.9.1 Manufacturer's Warranty: Manufacturer's standard limited warranty for the specified term.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer:2.1.1.1 Address: Crossfield Products Corporation, which is located at: 3000 E. Harcourt

Street; Rancho Dominguez, CA 90221; ASD Phone: 310-886-9100; Fax: 310-886-9119; Email: [email protected]; Web: www.dexotex.com.

2.1.1.2 Address: Crossfield Products Corporation, which is located at: 140 Valley Road; Roselle Park, NJ 07204; ASD Phone: 908-245-2800; Fax: 908-245-0659; Email: [email protected]; Web: www.dexotex.com.

2.1.1.3 Address: Crossfield Products Corporation, which is located at: 128 Industrial

09 67 23 -5

Drive, Cibolo, TX 78108; ASD Phone: 210-888-0449; Email: [email protected]; Web: www.dexotex.com.

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions must be submitted two weeks prior to bid date. Substitution request received after will not be considered. Request will be considered per Section 01 60 00 - Product Requirements.

2.2 DECORATIVE RESINOUS FLOORING

2.2.1 Troweled Epoxy Resin Composition Flooring:2.2.1.1 Basis of Design: Dex-O-Tex Cheminert CFS by Crossfield Products.2.2.1.2 Physical Properties:

2.2.1.2.1 Compressive Strength (ASTM C579): 11,000 psi (75.8 MPa).2.2.1.2.2 Tensile Strength (ASTM C307): 2084 psi (14.37 MPa).2.2.1.2.3 Flexural Modulus of Elasticity (ASTM C580): 4300 psi (29.6 MPa).2.2.1.2.4 Water Absorption (MIL-PRF-3134): Less than 1 percent.2.2.1.2.5 Surface Hardness (ASTM D2240) 85 Durometer "D".2.2.1.2.6 Abrasion Resistance (ASTM D4060): 0.04 gr.2.2.1.2.7 Impact Resistance (MIL-PRF-3134, Paragraph 4.7.3): 0.024 inch (0.61

mm) maximum, no chipping, cracking, or loss of adhesion.2.2.1.2.8 Impact Resistance (Gardner Impact Tester): No chipping, cracking, or

delamination and not more than 0.014 inch (0.36 mm) indentation.2.2.1.2.9 Adhesion (ACI 503.1): 400 psi (2.76 MPa), 100 percent failure in concrete.2.2.1.2.10 Electrical Conductivity (NFPA 56A): Di-electric.2.2.1.2.11 Flammability-Critical Radiant Flux (ASTM E648): Greater than 1.07

watts/sq.cm.2.2.1.3 Total Thickness: 1/4 inch (6 mm).2.2.1.4 Body Coat: 1/8 inch (3 mm) thick with broadcast ceramic quartz aggregate.2.2.1.5 Colors: _____.2.2.1.6 Colors: To be selected by Architect from manufacturer's standard colors.2.2.1.7 Colors: As indicated on Drawings.2.2.1.8 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.1.9 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.1.10 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac

epoxy.2.2.1.11 Top Coat: Quik-Glaze Clear Gloss. UV and abrasion resistant High build

Polyaspartic.2.2.1.12 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.1.13 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.1.14 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.1.15 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.2.1.16 Waterproofing Membrane: Type recommended by flooring manufacturer for type

of service and floor condition indicated.2.2.1.17 Vapor Control Primer Membrane: Type recommended by flooring manufacturer

for type of service and floor condition indicated.2.2.1.18 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer

for service condition of underlayment.

2.2.2 Decorative Flake Polymeric Floor Coating:2.2.2.1 Basis of Design: Dex-O-Tex Colorflake L by Crossfield Products.2.2.2.2 Physical Properties:

2.2.2.2.1 Pencil Hardness (ASTM D3363): 3H.2.2.2.2.2 Impact Resistance (ASTM D2794): Direct 50 in-lbs. (5.65 Nm), Reverse 10

in-lbs. (1.13 Nm).2.2.2.2.3 Thermal Shock (ASTM D1211): Complies.

09 67 23 -6

2.2.2.2.4 Chemical Resistance (ASTM D1308):2.2.2.2.4.1 Gasoline: No Effect.2.2.2.2.4.2 Kerosene: No Effect.2.2.2.2.4.3 Skydrol: No Effect.2.2.2.2.4.4 Isopropyl Alcohol: No Effect.2.2.2.2.4.5 Toluene: No Effect.2.2.2.2.4.6 Hydrogen Peroxide: Slight Stain.2.2.2.2.4.7 Hydrochloric Acid (25 percent): No Effect.

2.2.2.3 Total Thickness: 15 to 21 mils (0.38 to 0.53 mm).2.2.2.4 Body Coat: 8 to 12 mil (0.20 to 0.30 mm) thick.2.2.2.5 Colorflake: Broadcast PVC color chip.2.2.2.6 Colors: _____.2.2.2.7 Colors: To be selected by Architect from manufacturer's standard colors.2.2.2.8 Colors: As indicated on Drawings.2.2.2.9 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.2.10 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.2.11 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac



of service and floor condition indicated.2.2.2.18 Vapor Control Primer Membrane: Type recommended or produced by

manufacturer of flooring system for type of service and floor condition indicated.2.2.2.19 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.2.3 Decorative Colored Flake Flooring and Waterproof Membrane:2.2.3.1 Basis of Design: Dex-O-Tex Elastaflake RFS by Crossfield Products.2.2.3.2 Membrane Properties:

2.2.3.2.1 Tensile Strength: 1500 psi (10.3 KPa) at 77 degrees F (25 degrees C).2.2.3.2.2 Tensile Elongation: 17,150 psi (118.2 KPa).2.2.3.2.3 Tear Strength: 120.

2.2.3.3 Physical Properties:2.2.3.3.1 Compressive Strength (ASTM D695): 9,000 psi (62.1 MPa).2.2.3.3.2 Tensile Strength (ASTM D638): 1,200 psi (8.27 MPa).2.2.3.3.3 Hardness (ASTM D2240, Shore D): 80 to 85.2.2.3.3.4 Impact Resistance (ASTM D2794): Passes.2.2.3.3.5 Flexibility (ASTM D1737, 180 degree bend, 3/4 inch (19 mm) Mandrel):

Passes.2.2.3.3.6 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in

concrete.2.2.3.3.7 Thermal Shock Resistance (ASTM D1211), Cycle of immersion in boiling

water 10 minutes followed by ice water 10 minutes: Passes 6 cycles.2.2.3.3.8 Co-efficient of Static Friction (ASTM F609): Dry-Rubber 0.68, Leather 0.71.2.2.3.3.9 Microbial Resistance (ASTM G21): Passes, Rating 1.2.2.3.3.10 Chemical Resistance (ASTM D1308):

2.2.3.3.10.1 Betadine: Slight Stain.2.2.3.3.10.2 Gasoline: No Effect.2.2.3.3.10.3 Hydraulic Fluid: No Effect.2.2.3.3.10.4 Hydrochloric Acid (30 percent): No Effect.2.2.3.3.10.5 Hydrogen Peroxide (50 percent): No Effect.

09 67 23 -7

2.2.3.3.10.6 Isopropyl Alcohol: No Effect.2.2.3.3.10.7 Motor Oil: No Effect.2.2.3.3.10.8 Nitric Acid (20 percent): No Effect.2.2.3.3.10.9 Phosphoric Acid (20 percent): No Effect.2.2.3.3.10.10 Salt Water: No Effect.2.2.3.3.10.11 Skydrol: No Effect.2.2.3.3.10.12 Sodium Hypochlorite (15 percent): No Effect.2.2.3.3.10.13 Sodium Hydroxide (50 percent): No Effect.2.2.3.3.10.14 Sulfuric Acid (50 percent): No Effect.2.2.3.3.10.15 Toluene (Toluol): No Effect.

2.2.3.4 Total Thickness: 0.125 inch (3.2 mm).2.2.3.5 Body Coat: 80 mils ( mm) thick.2.2.3.6 Colors: _____.2.2.3.7 Colors: To be selected by Architect from manufacturer's standard colors.2.2.3.8 Colors: As indicated on Drawings.2.2.3.9 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.3.10 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.3.11 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac






2.2.4 Troweled Epoxy Mosaic Composition Flooring:2.2.4.1 Basis of Design: Dex-O-Tex Cheminert Terracolor with chemical resistant top

finish by Crossfield Products.2.2.4.2 Physical Properties:

2.2.4.2.1 Compressive Strength (ASTM C579): 8,576 psi (59.1 MPa).2.2.4.2.2 Tensile Strength (ASTM C307): 1,619 psi (11.2 MPa).2.2.4.2.3 Flexural Modulus of Elasticity (ASTM C580): 4300 psi (29.6 MPa).2.2.4.2.4 Surface Hardness (ASTM D2240) 81 Durometer "D".2.2.4.2.5 Abrasion Resistance (ASTM D1044): 0.0 gr. loss.2.2.4.2.6 Indentation (MIL-PRF-3134): Greater than 1 percent.2.2.4.2.7 Impact Resistance (Gardner Impact Tester): No chipping, cracking, or

delamination and not more than 0.014 inch (0.36 mm) indentation.2.2.4.2.8 Adhesion (ACI 503.1): 400 psi (2.76 MPa), 100 percent failure in concrete.2.2.4.2.9 Electrical Conductivity (NFPA 56A): Di-electric.2.2.4.2.10 Flammability-Critical Radiant Flux (ASTM E648): 1.07 watts/sq cm

minimum.2.2.4.3 Total Thickness: 1/4 inch (6 mm).2.2.4.4 Colors: _____.2.2.4.5 Colors: To be selected by Architect from manufacturer's standard colors.2.2.4.6 Colors: As indicated on Drawings.2.2.4.7 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.4.8 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.4.9 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac

epoxy.

09 67 23 -8

2.2.4.10 Top Coat: Quik-Glaze Clear Gloss. UV and abrasion resistant High build Polyaspartic.

2.2.4.11 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.4.12 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.4.13 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.4.14 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.2.4.15 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.2.5 Polymerized Cementitious Coating:2.2.5.1 Basis of Design: Dex-O-Tex Resistite Micro Topping with chemical resistant top

finish by Crossfield Products.2.2.5.2 Physical Properties:

2.2.5.2.1 Compressive Strength (ASTM C109): 2,440 psi (16.8 MPa).2.2.5.2.2 Tensile Strength (ASTM C109): 430 psi (2.96 MPa).2.2.5.2.3 Flammability (ASTM E84): Flame Spread 4, Smoke Density 0.2.2.5.2.4 Salt Spray Resistance (ASTM B117): 1000 hours, no visible degradation.2.2.5.2.5 Freeze-Thaw Resistance (ASTM C672): Thirty-two cycles, "O" Scaling.2.2.5.2.6 Surface Hardness (ASTM D2240) 82 Durometer "A".2.2.5.2.7 Water Vapor Permeability (ASTM E96): 1.95 perms/inch.2.2.5.2.8 Absorption: Less than 2 percent.

2.2.5.3 Colors: _____.2.2.5.4 Colors: To be selected by Architect from manufacturer's standard colors.2.2.5.5 Colors: As indicated on Drawings.2.2.5.6 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.5.7 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.5.8 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.2.5.10 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.5.11 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.5.12 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.5.13 Total Thickness: 1/16 inch (1.8 mm).2.2.5.14 Total Thickness: 3/32 inch (2.4 mm).2.2.5.15 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.2.5.16 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.2.6 Metallic and Pearlescent Color System:2.2.6.1 Basis of Design: Dex-O-Tex Metallic Luster with chemical resistant top finish by

Crossfield Products.2.2.6.2 Physical Properties:

2.2.6.2.1 Viscosity (mixed): 750 cps.2.2.6.2.2 Solids Content: 100 percent.2.2.6.2.3 Pot Live: Approximately 30 minutes.2.2.6.2.4 Compressive Strength (ASTM D695): 12,900 psi (88.9 MPa).2.2.6.2.5 Tensile Strength (ASTM D638): 4,400 psi (30.3 MPa).

09 67 23 -9

2.2.6.2.6 Adhesion (ASTM D4541): 400 psi (2.76 MPa).2.2.6.2.7 Water Absorption (MIL-D-3134): Less than 1.0 percent.2.2.6.2.8 Abrasion Resistance (ASTM D4060): 0.09 gr.2.2.6.2.9 Flammability (ASTM D635): Self-extinguishing bonded to concrete.2.2.6.2.10 VOC Content: 3 g/L.2.2.6.2.11 Microbial Resistance (ASTM G21): Passes, Rating 1.

2.2.6.3 Colors: _____.2.2.6.4 Colors: To be selected by Architect from manufacturer's standard colors.2.2.6.5 Colors: As indicated on Drawings.2.2.6.6 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.6.7 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.6.8 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.2.6.10 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.6.11 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.6.12 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.6.13 Clear Coat: Type recommended by manufacturer of flooring system for type of

service and floor condition indicated.2.2.6.14 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.2.7 Decorative Quartz Epoxy Flooring:2.2.7.1 Basis of Design: Dex-O-Tex Decor-Flor by Crossfield Products.2.2.7.2 Physical Properties:

2.2.7.2.1 Compressive Strength, Complete System (ASTM C109): 8,556 psi (59.0 MPa).

2.2.7.2.2 Compressive Strength, Resin Component (ASTM D695): 12,900 psi (88.9 MPa).

2.2.7.2.3 Surface Hardness (ASTM D2240) 85.5 Durometer "D".2.2.7.2.4 Aggregate Hardness (Moh's Mineral Scale): 6-1/2 to 7.2.2.7.2.5 Indentation, Steadily Applied Load (MIL-PRF-3134, Paragraph 4.7.4.2.1):

0.005 indentation.2.2.7.2.6 Impact Resistance (MIL-PRF-3134, Paragraph 4.7.3): 0.011 indentation,

no cracking or loss of adhesion.2.2.7.2.7 Adhesion (ACI 503.1): 345 psi (2.38 MPa), 100 percent failure in concrete.2.2.7.2.8 Water Absorption (MIL-PRF-3134): Less than 1 percent.2.2.7.2.9 Abrasion Resistance (ASTM C501: 19 Wear Index (H-22 Wheel).2.2.7.2.10 Tensile Strength (ASTM D638): 4,400 psi (30.3 MPa).2.2.7.2.11 Elongation (ASTM D638): 19.6 percent.

2.2.7.3 Colors: _____.2.2.7.4 Colors: To be selected by Architect from manufacturer's standard colors.2.2.7.5 Colors: As indicated on Drawings.2.2.7.6 Broadcast: Ceramic coated quartz aggregate.2.2.7.7 Thickness: 1/16 - 1/8 inch (1.6 to 3 mm).2.2.7.8 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.7.9 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.7.10 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.

09 67 23 -10

2.2.7.12 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.7.13 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.7.14 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.7.15 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.2.7.16 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.2.8 Decorative Colored Quartz Troweled Epoxy Flooring:2.2.8.1 Basis of Design: Dex-O-Tex Troweled Decor-Flor by Crossfield Products.2.2.8.2 Physical Properties:

2.2.8.2.1 Compressive Strength, Complete System (ASTM C579): 10,500 psi (738 kg/sq.cm).

2.2.8.2.2 Compressive Strength, Resin and Hardener (ASTM D695): 12,900 psi (907 kg/sq.cm).

2.2.8.2.3 Tensile Strength, Complete System (ASTM C307): 1,800 psi (127 kg/sq.cm).

2.2.8.2.4 Tensile Strength, Resin and Hardener (ASTM D638): 5,000 psi (352 kg/sq.cm).

2.2.8.2.5 Flexural Strength (ASTM C580): 4,000 psi (281 kg/sq.cm).2.2.8.2.6 Surface Hardness (ASTM D2240) 80-85 Durometer "D".2.2.8.2.7 Aggregate Hardness (Moh's Mineral Scale): 6-1/2 to 7.2.2.8.2.8 Indentation, Steadily Applied Load (MIL-PRF-3134, Paragraph 4.7.4.2.1):

0.005 indentation.2.2.8.2.9 Impact Resistance (MIL-PRF-3134, Paragraph 4.7.3): 0.011 indentation,

no cracking or loss of adhesion.2.2.8.2.10 Adhesion (ACI 503.1): 400 psi (28.1 kg/sq.cm), 100 percent failure in

concrete.2.2.8.2.11 Water Absorption (MIL-PRF-3134): Less than 1 percent.2.2.8.2.12 Abrasion Resistance (ASTM D4060): 0.04 gr.2.2.8.2.13 Antimicrobial Resistance (ASTM G21): Passes.2.2.8.2.14 Flammability (ASTM D635): Self-extinguishing, bonded to concrete.

2.2.8.3 Thickness: 3/16 to 1/4 inch (5 to 6 mm).2.2.8.4 Colors: _____.2.2.8.5 Colors: To be selected by Architect from manufacturer's standard colors.2.2.8.6 Colors: As indicated on Drawings.2.2.8.7 Top Coat: Cheminert Clearsealer. High performance epoxy.2.2.8.8 Top Coat: Decor-Flor. Clear high performance epoxy.2.2.8.9 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.2.8.11 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.2.8.12 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.2.8.13 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.2.8.14 Moisture Mitigation System: Concrete, especially slab on grade should be tested

per ASTM F1869. If pounds exceed flooring limit remedial action must be taken.2.2.8.15 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.2.8.16 Waterproofing Membrane: Type recommended by flooring manufacturer for type



09 67 23 -11


2.3 URETHANE CONCRETE FLOORING

2.3.1 Troweled Urethane Cement Composition Flooring:2.3.1.1 Basis of Design: Dex-O-Tex Tek-Crete TT by Crossfield Products.2.3.1.2 Physical Properties:

2.3.1.2.1 Compressive Strength (ASTM C579): 7,100 psi (49.0 MPa).2.3.1.2.2 Density (ASTM C905): 130 pcf (20.4 kN/cu.m).2.3.1.2.3 Water Absorption (MIL-PRF-3134): 0.64 percent.2.3.1.2.4 Surface Hardness (ASTM D2240) 85.5 Durometer "D".2.3.1.2.5 Abrasion Resistance (ASTM D1044): 0.0 gr.2.3.1.2.6 Adhesion (ASTM D4541): 675 psi (4.65 MPa), 100 percent failure in

concrete.2.3.1.2.7 Flammability-Critical Radiant Flux (ASTM E648): 1.07 watts/sq.cm.2.3.1.2.8 Resistance to Fungal Growth (ASTM G21): Passes.

2.3.1.3 Body Coat: 3/8 inch (9.5 mm) thick.2.3.1.4 Colors: _____.2.3.1.5 Colors: To be selected by Architect from manufacturer's standard colors.2.3.1.6 Colors: As indicated on Drawings.2.3.1.7 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.3.1.8 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.1.9 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.3.2 Troweled Slurry Urethane Cement Composition Flooring:2.3.2.1 Basis of Design: Dex-O-Tex Tek-Crete SL by Crossfield Products.2.3.2.2 Physical Properties:

2.3.2.2.1 Compressive Strength (ASTM C579): 8,100 psi (55.8 MPa).2.3.2.2.2 Density (ASTM C905): 130 pcf (20.4 kN/cu.m).2.3.2.2.3 Water Absorption (MIL-PRF-3134): 0.64 percent.2.3.2.2.4 Surface Hardness (ASTM D2240) 85-90 Durometer "D".2.3.2.2.5 Abrasion Resistance (ASTM D1044): 0.0 gr.2.3.2.2.6 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in

concrete.2.3.2.2.7 Flammability-Critical Radiant Flux (ASTM E648): 1.07 watts/sq.cm.2.3.2.2.8 Resistance to Fungal Growth (ASTM G21): Passes, Rating 1.

2.3.2.3 Body Coat: 3/16 to 1/4 inch (5 to 6 mm) thick.2.3.2.4 Colors: _____.2.3.2.5 Colors: To be selected by Architect from manufacturer's standard colors.2.3.2.6 Colors: As indicated on Drawings.2.3.2.7 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.3.2.9 Top Coat: Quik-Glaze Pigmented. UV and abrasion resistant High build

Polyaspartic.2.3.2.10 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.3.2.11 Top Coat: Posi-Tred CR Pigmented. Heat and chemical resistant Novolac epoxy.2.3.2.12 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.2.13 Waterproofing Membrane: Type recommended by flooring manufacturer for type

of service and floor condition indicated.

09 67 23 -12

2.3.2.14 Vapor Control Primer Membrane: Type recommended by flooring manufacturer for type of service and floor condition indicated.

2.3.2.15 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer for service condition of underlayment.

2.3.3 Troweled Urethane Cement Composition Flooring with Slip Resistant Broadcast:2.3.3.1 Basis of Design: Dex-O-Tex Tek-Crete SL-B by Crossfield Products.2.3.3.2 Physical Properties:

2.3.3.2.1 Compressive Strength (ASTM C579): 8,100 psi (55.8 MPa).2.3.3.2.2 Thermal Distortion (350 degrees F Emersion): Passes.2.3.3.2.3 Tensile Strength (ASTM C307): 1,000 psi (6.89 MPa).2.3.3.2.4 Flexural Strength (ASTM C580): 2,000 psi (13.8 MPa).2.3.3.2.5 Thermal Co-Efficient of Thermal Expansion (ASTM C531): 1.5 x 10E5.2.3.3.2.6 Density (ASTM C905): 130 pcf (20.4 kN/cu.m).2.3.3.2.7 Water Absorption (MIL-PRF-3134): 0.64 percent.2.3.3.2.8 Surface Hardness (ASTM D2240) 85-90 Durometer "D".2.3.3.2.9 Abrasion Resistance (ASTM D1044): 0.0 gr.2.3.3.2.10 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in


2.3.3.3 Body Coat: 3/16 to 1/4 inch (5 to 6 mm) thick with slip resistant aggregate.2.3.3.4 Colors: _____.2.3.3.5 Colors: To be selected by Architect from manufacturer's standard colors.2.3.3.6 Colors: As indicated on Drawings.2.3.3.7 Top Coat: Posi-Tred CR Pigmented. Heat and chemical resistant Novolac epoxy.2.3.3.8 Top Coat: Quik-Glaze Pigmented. UV and abrasion resistant High build

Polyaspartic.2.3.3.9 Top Coat: Tek-Crete Sealer CP.2.3.3.10 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.3.11 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.3.4 Troweled Urethane Cement Composition Flooring with Decorative Color Flake Broadcast:2.3.4.1 Basis of Design: Dex-O-Tex Tek-Crete SL-CF by Crossfield Products.2.3.4.2 Physical Properties:



2.3.4.3 Body Coat: 3/16 to 1/4 inch (5 to 6 mm) thick with color flake chip broadcast.2.3.4.4 Colors: _____.2.3.4.5 Colors: To be selected by Architect from manufacturer's standard colors.

09 67 23 -13

2.3.4.6 Colors: As indicated on Drawings.2.3.4.7 Top Coat: Cheminert Clearsealer. High performance epoxy.2.3.4.8 Top Coat: Decor-Flor. Clear high performance epoxy.2.3.4.9 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.3.4.11 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.3.4.12 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.4.13 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.3.5 Troweled Urethane Cement Composition Flooring with Decorative Color Quartz Broadcast:2.3.5.1 Basis of Design: Dex-O-Tex Tek-Crete SL-CQ by Crossfield Products.2.3.5.2 Physical Properties:



2.3.5.3 Colors: _____.2.3.5.4 Colors: To be selected by Architect from manufacturer's standard colors.2.3.5.5 Colors: As indicated on Drawings.2.3.5.6 Body Coat: 3/16 to 1/4 inch (5 to 6 mm) thick with colored quartz broadcast.2.3.5.7 Body Coat: 1/4 inch (6 mm) thick with colored quartz broadcast.2.3.5.8 Body Coat: 3/8 inch (9.5 mm) thick with colored quartz broadcast.2.3.5.9 Top Coat: Cheminert Clearsealer. High performance epoxy.2.3.5.10 Top Coat: Decor-Flor. Clear high performance epoxy.2.3.5.11 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac


Polyaspartic.2.3.5.13 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.3.5.14 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.5.15 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.3.6 UV Stable Polyurethane Composition Sealer:2.3.6.1 Basis of Design: Dex-O-Tex Tek-Crete Sealer CP by Crossfield Products.2.3.6.2 Colors: _____.

09 67 23 -14

2.3.6.3 Colors: To be selected by Architect from manufacturer's standard colors.2.3.6.4 Colors: As indicated on Drawings.2.3.6.5 UV stable.2.3.6.6 Withstands heavy and abusive service.2.3.6.7 Excellent chemical resistance.2.3.6.8 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.6.9 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.3.7 Skim Coat:2.3.7.1 Basis of Design: Dex-O-Tex Tek-Crete Skim Coat by Crossfield Products. Three

component urethane concrete coating.2.3.7.2 Thickness: 8 to 16 mils (0.203 to 0.406 mm).2.3.7.3 Colors: _____.2.3.7.4 Colors: To be selected by Architect from manufacturer's standard colors.2.3.7.5 Colors: As indicated on Drawings.2.3.7.6 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.3.7.7 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4 EPOXY FLOORING AND COATINGS

2.4.1 Troweled Epoxy Resin High-Density Flooring:2.4.1.1 Basis of Design: Dex-O-Tex Cheminert HD by Crossfield Products.2.4.1.2 Physical Properties:

2.4.1.2.1 Compressive Strength (ASTM C579): 11,000 psi (75.8 MPa).2.4.1.2.2 Tensile Strength (ASTM C307): 1,643 psi (11.3 MPa).2.4.1.2.3 Flexural Modulus of Elasticity (ASTM C580): 4,300 psi (29.6 MPa).2.4.1.2.4 Water Absorption (MIL-PRF-3134): 0.3 percent maximum.2.4.1.2.5 Surface Hardness (ASTM D2240) 85.5 Durometer "D".2.4.1.2.6 Abrasion Resistance (ASTM D1044): 0.0 gr.2.4.1.2.7 Impact Resistance (MIL-PRF-3134, Paragraph 4.7.3): 0.024 inch (0.61


delamination and not more than 0.014 inch (0.36 mm) indentation.2.4.1.2.9 Adhesion (ACI 503.1): 400 psi (2.76 MPa), 100 percent failure in concrete.2.4.1.2.10 Electrical Conductivity (NFPA 56A): Di-electric.2.4.1.2.11 Flammability-Critical Radiant Flux (ASTM E648): 1.07 watts/sq.cm.

2.4.1.3 Colors: _____.2.4.1.4 Colors: To be selected by Architect from manufacturer's standard colors.2.4.1.5 Colors: As indicated on Drawings.2.4.1.6 Thickness: 1/8 inch (3 mm).2.4.1.7 Thickness: 3/16 inch (5 mm).2.4.1.8 Thickness: 1/4 inch (6 mm).2.4.1.9 Top Coat: Quik-Glaze Clear Gloss. UV and abrasion resistant High build


Polyaspartic.

09 67 23 -15

2.4.1.11 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.4.1.12 Top Coat: Posi-Tred O Pigmented. Heat and chemical resistant Novolac epoxy.2.4.1.13 Top Coat: Posi-Tred CR Pigmented. Heat and chemical resistant Novolac epoxy.2.4.1.14 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac

epoxy.2.4.1.15 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.4.1.16 Top Coat: Aero-Flor 100 Pigmented. Polyurethane enamel UV resistant Sealer.2.4.1.17 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.4.1.18 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.1.19 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.2 Troweled Epoxy Resin High-Density Flooring:2.4.2.1 Basis of Design: Dex-O-Tex Cheminert K by Crossfield Products.2.4.2.2 Physical Properties:

2.4.2.2.1 Compressive Strength (ASTM C579): 11,000 psi (75.8 MPa).2.4.2.2.2 Tensile Strength (ASTM C307): 1,643 psi (11.3 MPa).2.4.2.2.3 Flexural Modulus of Elasticity (ASTM C580): 4,300 psi (29.6 MPa).2.4.2.2.4 Water Absorption (MIL-PRF-3134): 0.3 percent maximum.2.4.2.2.5 Surface Hardness (ASTM D2240) 85.5 Durometer "D".2.4.2.2.6 Abrasion Resistance (ASTM D1044): 0.04 gr.2.4.2.2.7 Impact Resistance (MIL-PRF-3134, Paragraph 4.7.3): 0.024 inch (0.61


delamination and not more than 0.014 inch (0.36 mm) indentation.2.4.2.2.9 Adhesion (ACI 503.1): 400 psi (2.76 MPa), 100 percent failure in concrete.2.4.2.2.10 Electrical Conductivity (NFPA 56A): Di-electric.2.4.2.2.11 Flammability-Critical Radiant Flux (ASTM E648): Greater than 1.07

watts/sq.cm.2.4.2.2.12 Co-efficient of Friction (MIL-PRF-3134 procedure - rubber shoe surface):

2.4.2.2.12.1 Fine Profile, Static Friction: Saltwater Solution on Surface: 0.95, Oil on Surface: 0.75.

2.4.2.2.12.2 Fine Profile, Sliding Friction: Saltwater Solution on Surface: 0.89, Oil on Surface: 0.44.

2.4.2.2.12.3 Medium Profile, Static Friction: Saltwater Solution on Surface: 1.03, Oil on Surface: 0.75.

2.4.2.2.12.4 Medium Profile, Sliding Friction: Saltwater Solution on Surface: 0.95, Oil on Surface: 0.45.

2.4.2.2.12.5 Coarse Profile, Static Friction: Saltwater Solution on Surface: 1.09, Oil on Surface: 0.85.

2.4.2.2.12.6 Coarse Profile, Sliding Friction: Saltwater Solution on Surface: 1.00, Oil on Surface: 0.56.

2.4.2.2.12.7 Very Coarse Profile, Static Friction: Saltwater Solution on Surface: 1.24, Oil on Surface: 0.78.

2.4.2.2.12.8 Very Coarse Profile, Sliding Friction: Saltwater Solution on Surface: 1.04, Oil on Surface: 0.59.

2.4.2.3 Thickness: 1/4 inch (6 mm).2.4.2.4 Colors: _____.2.4.2.5 Colors: To be selected by Architect from manufacturer's standard colors.2.4.2.6 Colors: As indicated on Drawings.2.4.2.7 Top Coat: Quik-Glaze Clear Gloss. UV and abrasion resistant High build

Polyaspartic.

09 67 23 -16

2.4.2.8 Top Coat: Quik-Glaze Pigmented. UV and abrasion resistant High build Polyaspartic.

2.4.2.9 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.4.2.10 Top Coat: Posi-Tred O Pigmented. Heat and chemical resistant Novolac epoxy.2.4.2.11 Top Coat: Posi-Tred CR Pigmented. Heat and chemical resistant Novolac epoxy.2.4.2.12 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac

epoxy.2.4.2.13 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.4.2.14 Top Coat: Aero-Flor 100 Pigmented. Polyurethane enamel UV resistant Sealer.2.4.2.15 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.2.16 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.3 Conductive, Troweled Epoxy Flooring:2.4.3.1 Basis of Design: Dex-O-Tex Conductive Cheminert K by Crossfield Products.2.4.3.2 Physical Properties:

2.4.3.2.1 Electrical Conductivity: Complies with the Following: NFPA 56, NFPA 99, US Army AMCR 385-100, and US Army NAVSEA OP-5: Complies.

2.4.3.2.2 Electrical Transmission, Point-to-Point / Point-to-Ground: 2.5E4 to 1E6 ohms.

2.4.3.2.3 Compressive Strength (ASTM D695): 21,600 psi (149 MPa).2.4.3.2.4 Surface Hardness (ASTM D2240) 82 Durometer "D".2.4.3.2.5 Tensile Strength (ASTM D638): 6,680 psi (46.1 MPa).2.4.3.2.6 Tensile Elongation (ASTM D638): 5.9 percent.2.4.3.2.7 Flexural Strength (ASTM D790): 12,200 psi (84.1 MPa).2.4.3.2.8 Modulus of Elasticity (ASTM D790): 4.1 x 10E4.2.4.3.2.9 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in

concrete.2.4.3.2.10 Abrasion Resistance (ASTM D4060): 0.04 gr.2.4.3.2.11 Microbial Resistance (ASTM G21): Passes, Rating 1.2.4.3.2.12 Chemical Resistance (Federal Standard 406, Method 7011):

2.4.3.2.12.1 Acetic Acid: No effect.2.4.3.2.12.2 ASTM No. 3 Oil: No effect.2.4.3.2.12.3 Distilled Water: No effect.2.4.3.2.12.4 Ethanol: No effect.2.4.3.2.12.5 Hydrochloric Acid, 10 percent: No effect.2.4.3.2.12.6 Industrial Detergent, 0.025 percent: No effect.2.4.3.2.12.7 Isopropyl Alcohol: No effect.2.4.3.2.12.8 Lard: No effect.2.4.3.2.12.9 Mineral Oil: No effect.2.4.3.2.12.10 Sulfuric Acid, 30 percent: No effect.

2.4.3.3 Thickness: 3/16 to 1/4 inch (5 to 6 mm).2.4.3.4 Electrical Grounding and Strapping Points with Conductive Tape per ANSI/ESD

S 6.1: Grounding, specified by Electrical Engineer and connected by an electrician in appropriate Division 26 specifications.

2.4.3.5 Colors: _____.2.4.3.6 Colors: To be selected by Architect from manufacturer's standard colors.2.4.3.7 Colors: As indicated on Drawings.2.4.3.8 Top Coat: Electro-Flor CD.2.4.3.9 Top Coat: Conductive Chem Rez M.2.4.3.10 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.3.11 Waterproofing Membrane: Type recommended by flooring manufacturer for type

09 67 23 -17




2.4.4 Self-Leveling, Seamless Epoxy Flooring:2.4.4.1 Basis of Design: Dex-O-Tex Cheminert L by Crossfield Products.2.4.4.2 Physical Properties:

2.4.4.2.1 Compressive Strength:2.4.4.2.1.1 Complete System (ASTM C579): 9,000 psi (62.1 MPa).2.4.4.2.1.2 Resin and Hardener (ASTM D695): 10,000 psi (68.9 MPa).

2.4.4.2.2 Tensile Strength (ASTM C307): 1,600 psi (11.0 MPa).2.4.4.2.3 Flexural Strength (ASTM C580): 4,000 psi (27.6 MPa).2.4.4.2.4 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in

concrete.2.4.4.2.5 Surface Hardness (ASTM D2240) 80 to 85 Durometer "D".2.4.4.2.6 Water Absorption (MIL-PRF-3134): 0.58 percent.2.4.4.2.7 Abrasion Resistance (ASTM D4060): 0.04 gr.2.4.4.2.8 Impact Resistance (MIL-D-3134, Paragraph 4.7.3): 0.001 indentation, no

loosening or cracking.2.4.4.2.9 Impact Resistance (MIL-D-3134, Paragraph 4.7.4.2.1): 0.0008.2.4.4.2.10 Adhesion (MIL-D3134, Paragraph 4.7.14): Passes.2.4.4.2.11 Microbial Resistance (ASTM G21): Passes, Rating 1.

2.4.4.3 Thickness: 1/16 to 1/8 inch (1.6 to 3 mm).2.4.4.4 Colors: _____.2.4.4.5 Colors: To be selected by Architect from manufacturer's standard colors.2.4.4.6 Colors: As indicated on Drawings.2.4.4.7 Top Coat: Quik-Glaze Clear Gloss. UV and abrasion resistant High build


Polyaspartic.2.4.4.9 Top Coat: Quik-Glaze FC. UV and abrasion resistant High build Polyaspartic.2.4.4.10 Top Coat: Posi-Tred O Pigmented. Heat and chemical resistant Novolac epoxy.2.4.4.11 Top Coat: Posi-Tred CR Pigmented. Heat and chemical resistant Novolac epoxy.2.4.4.12 Top Coat: Posi-Tred CR Clear Amber. Heat and chemical resistant Novolac

epoxy.2.4.4.13 Top Coat: Aero-Flor 100 Clear Gloss. Polyurethane enamel UV resistant Sealer.2.4.4.14 Top Coat: Aero-Flor 100 Pigmented. Polyurethane enamel UV resistant Sealer.2.4.4.15 Top Coat: HPT. UV and abrasion resistant high gloss moisture cured urethane.2.4.4.16 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.4.17 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.5 Electro-Static Dissipative, Thin Film Self-Leveling Epoxy Resin Composition Flooring:2.4.5.1 Basis of Design: Dex-O-Tex Electro-Flor ESD by Crossfield Products.2.4.5.2 Physical Properties:

2.4.5.2.1 Electrical Transmission, Floor-to-Floor Resistance (ASTM F150): One million ohms to one billion ohms.

2.4.5.2.2 Surface Hardness (ASTM D2240) 85 Durometer "D".2.4.5.2.3 Impact Resistance (ASTM D2794): 160 in/lbs.2.4.5.2.4 Indentation (MIL-PRF-3134, Paragraph 4.7.4): Less than 0.0008.

09 67 23 -18

2.4.5.2.5 Adhesion (MIL-PRF-3134, Paragraph 4.7.14): 337 psi (2.32 MPa).2.4.5.2.6 Tensile Strength (ASTM D2370): 5000 psi (35 MPa).2.4.5.2.7 Water Absorption (MIL-PRF-3134, Paragraph 4.7.8): Less than 0.58

percent.2.4.5.2.8 Abrasion Resistance (ASTM D4060) 15 mg loss.

2.4.5.3 Colors: Gray.2.4.5.4 Colors: To be selected by Architect from manufacturer's standard colors.2.4.5.5 Colors: As indicated on Drawings.2.4.5.6 Body Coat: 6 mils (0.152 mm) dry film thickness.2.4.5.7 Top Coat: 6 mils (0.152 mm) dry film thickness.2.4.5.8 Electrical Grounding and Strapping Points with Conductive Tape per ANSI/ESD

S 6.1: Grounding specified by Electrical Engineer and connected by an electrician in appropriate Division 26 specifications.

2.4.5.9 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.5.10 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.6 Conductive, Thin Film Epoxy Resin Composition Flooring:2.4.6.1 Basis of Design: Dex-O-Tex Electro-Flor CD by Crossfield Products.2.4.6.2 Physical Properties:

2.4.6.2.1 Electrical Transmission, Floor-to-Floor Resistance (ASTM F150): 25E4 to 1E6 Twenty-Five Thousand ohms to one Million ohms.

2.4.6.2.2 Surface Hardness (ASTM D2240) 85 Durometer "D".2.4.6.2.3 Impact Resistance (ASTM D2794) 160 in/lbs.2.4.6.2.4 Indentation (MIL-PRF-3134, Paragraph 4.7.4): Less than 0.0008.2.4.6.2.5 Adhesion (MIL-PRF-3134, Paragraph 4.7.14): 337 psi (2.32 MPa).2.4.6.2.6 Tensile Strength (ASTM D2370): 5000 psi (35 MPa).2.4.6.2.7 Water Absorption (MIL-PRF-3134, Paragraph 4.7.8): Less than 0.58

percent2.4.6.2.8 Abrasion Resistance (ASTM D4060) 15 mg loss.

2.4.6.3 Colors: Gray.2.4.6.4 Colors: To be selected by Architect from manufacturer's standard colors.2.4.6.5 Colors: As indicated on Drawings.2.4.6.6 Body Coat: 6 mils (0.152 mm) dry film thickness.2.4.6.7 Top Coat: 6 mils (0.152 mm) dry film thickness.2.4.6.8 Electrical and Strapping Points with Conductive Tape per ANSI/ESD S 6.1.2.4.6.9 Grounding specified by Electrical Engineer and connected by an electrician in

appropriate Division 26 specifications.2.4.6.10 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.6.11 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.7 Conductive, Fluid Applied, Monolithic, High Solids Epoxy Flooring:2.4.7.1 Basis of Design: Dex-O-Tex Electro-Flor HS CD by Crossfield Products.2.4.7.2 Physical Properties:

2.4.7.2.1 VOC Content: Less than 100 g/L.2.4.7.2.2 Electrical Transmission, ESD Dissipative (SD) 7.1: 25E4 to 1E6 ohms.2.4.7.2.3 Impact Resistance (ASTM D2794): Passes.

09 67 23 -19

2.4.7.2.4 Flexibility, 1/8 inch Mandrel (ASTM D522): Passes.2.4.7.2.5 Adhesion (ASTM D3359): 5B.2.4.7.2.6 Abrasion Resistance, CS-1 wheels, 1 kgms, 1k cycles (ASTM D4060): 56

mg.2.4.7.2.7 Microbial Resistance (ASTM G21): Passes, Rating 1.

2.4.7.3 Colors: _____.2.4.7.4 Colors: To be selected by Architect from manufacturer's standard colors.2.4.7.5 Colors: As indicated on Drawings.2.4.7.6 Skim Coat: 18 mils (mm) dry film thickness.2.4.7.7 Body Coat: 6 mils (0.152 mm) dry film thickness.2.4.7.8 Top Coat: 6 mils (0.152 mm) dry film thickness.2.4.7.9 Electrical Grounding and Strapping Points with Conductive Tape per ANSI/ESD

S 6.1: Grounding specified by Electrical Engineer and connected by an electrician in appropriate Division 26 specifications.

2.4.7.10 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.7.11 Vapor Control Primer Membrane: Type recommended by flooring manufacturer



2.4.8 Slip Retardant Epoxy Coating:2.4.8.1 Basis of Design: Dex-O-Tex Posi-Tred O by Crossfield Products.2.4.8.2 Physical Properties:

2.4.8.2.1 Co-efficient of Friction (MIL-PRF-3134e):2.4.8.2.1.1 Fine Profile, Static Friction: Saltwater Solution on Surface: 0.95,

Oil on Surface: 0.75.2.4.8.2.1.2 Fine Profile, Sliding Friction: Saltwater Solution on Surface: 0.89,

Oil on Surface: 0.44.2.4.8.2.1.3 Medium Profile, Static Friction: Saltwater Solution on Surface:

1.03, Oil on Surface: 0.75.2.4.8.2.1.4 Medium Profile, Sliding Friction: Saltwater Solution on Surface:

0.95, Oil on Surface: 0.45.2.4.8.2.1.5 Coarse Profile, Static Friction: Saltwater Solution on Surface:

1.09, Oil on Surface: 0.85.2.4.8.2.1.6 Coarse Profile, Sliding Friction: Saltwater Solution on Surface:

1.00, Oil on Surface: 0.56.2.4.8.2.1.7 Very Coarse Profile, Static Friction: Saltwater Solution on Surface:

1.24, Oil on Surface: 0.78.2.4.8.2.1.8 Very Coarse Profile, Sliding Friction: Saltwater Solution on

Surface: 1.04, Oil on Surface: 0.59.2.4.8.2.2 Chemical Resistance, Spot-Test Open 24 Hours (ASTM D1308):

2.4.8.2.2.1 Citric Acid, 70 Percent: No Effect.2.4.8.2.2.2 Hydrochloric Acid, 10 Percent: No Effect.2.4.8.2.2.3 Sulfuric Acid, 50 Percent: No Effect.2.4.8.2.2.4 Sodium Hydroxide, 5 Percent: No Effect.2.4.8.2.2.5 Lactic Acid: Discoloration.2.4.8.2.2.6 Beef and Bacon Fat: No Effect.2.4.8.2.2.7 Hydraulic Fluid: No Effect.2.4.8.2.2.8 Urine: No Effect.

2.4.8.2.3 Resistance to Immersion, SAE 10 Oil, Detergent Solution (MIL-PRF-3134, Paragraph 4.6.11): No softening, loss of adhesion, or other form of deterioration.

2.4.8.2.4 Fire Resistance (ASTM E162): Flame Spread Index 0, Smoke Deposited 2mg.

2.4.8.3 Colors: _____.2.4.8.4 Colors: To be selected by Architect from manufacturer's standard colors.

09 67 23 -20

2.4.8.5 Colors: As indicated on Drawings.2.4.8.6 Very Fine Profile, Texture: 12 mils (0.305 mm).2.4.8.7 Fine Profile, Texture: 18 mils (0.46 mm).2.4.8.8 Medium Profile, Texture: 32 mils (0.81 mm).2.4.8.9 Coarse Profile, Texture: 54 mils (1.37 mm).2.4.8.10 Very Coarse Profile, Texture: 90 mils (2.29 mm).2.4.8.11 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.8.12 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.4.9 Chemical, Heat, and Skid Resistant Epoxy Coating:2.4.9.1 Basis of Design: Dex-O-Tex Posi-Tred CR by Crossfield Products.2.4.9.2 Physical Properties:

2.4.9.2.1 Surface Hardness (ASTM D2240) 80-85 Durometer "D".2.4.9.2.2 Tensile Strength (ASTM 638): 1,200 psi (8.27 MPa).2.4.9.2.3 Flexibility (ASTM D1737): No loosening.2.4.9.2.4 Adhesion (ASTM D4541): Greater than 400 psi (2.76 MPa).2.4.9.2.5 Adhesion, Crosshatch (ASTM D3359): 5B, no loosening.2.4.9.2.6 Thermal Shock Resistance (ASTM D1211): No failure.2.4.9.2.7 Temperature Resistance: No measurable softening, deflection, or integrity

loss upon 8 hours immersion in boiling water.2.4.9.2.8 Water Absorption (MIL-D-3134, 7 day immersion): Nil.2.4.9.2.9 Co-efficient of Friction (MIL-PRF-3134):

2.4.9.2.9.1 Fine Profile, Static Friction: Saltwater on Surface: 0.95. Oil on Surface: 0.75.

2.4.9.2.9.2 Fine Profile, Sliding Friction: Saltwater on Surface: 0.8. Oil on Surface: 0.44.

2.4.9.2.9.3 Medium Profile, Static Friction: Saltwater on Surface: 1.03. Oil on Surface: 0.75.

2.4.9.2.9.4 Medium Profile, Sliding Friction: Saltwater on Surface: 0.95. Oil on Surface: 0.45.

2.4.9.2.9.5 Coarse Profile, Static Friction: Saltwater on Surface: 1.09. Oil on Surface: 0.85.

2.4.9.2.9.6 Coarse Profile, Sliding Friction: Saltwater on Surface: 1.00. Oil on Surface: 0.56.

2.4.9.2.9.7 Very Coarse Profile, Static Friction: Saltwater on Surface: 1.24. Oil on Surface: 0.88.

2.4.9.2.9.8 Very Coarse Profile, Sliding Friction: Saltwater on Surface: 1.04. Oil on Surface: 0.59.

2.4.9.2.10 Flammability-Critical Radiant Flux (ASTM E648): 1.07 watts/sq.cm.2.4.9.2.11 Microbial Resistance (ASTM G21): Passes, Rating 1.

2.4.9.3 Colors: _____.2.4.9.4 Colors: To be selected by Architect from manufacturer's standard colors.2.4.9.5 Colors: As indicated on Drawings.2.4.9.6 Very Fine Profile, Texture: 12 mils (0.305 mm).2.4.9.7 Fine Profile, Texture: 12 mils (0.30 mm).2.4.9.8 Medium Profile, Texture: 23 mils (0.58 mm).2.4.9.9 Coarse Profile, Texture: 50 mils (1.27 mm).2.4.9.10 Very Coarse Profile, Texture: 65 mils (1.65 mm).2.4.9.11 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.4.9.12 Waterproofing Membrane: Type recommended by flooring manufacturer for type

of service and floor condition indicated.

09 67 23 -21

2.4.9.13 Vapor Control Primer Membrane: Type recommended by flooring manufacturer for type of service and floor condition indicated.


2.5 POLYASPARTIC AND URETHANE COATINGS

2.5.1 Pigmented Urethane Coating:2.5.1.1 Basis of Design: Dex-O-Tex Aero-Flor 100 Pigmented by Crossfield Products.2.5.1.2 Physical Properties:

2.5.1.2.1 VOC Content: 100 g/L.2.5.1.2.2 Tensile Strength (ASTM C307): 8,600 psi (5.93 MPa).2.5.1.2.3 Elongation (ASTM D882): 10 percent.2.5.1.2.4 Coefficient of Friction (ASTM F1679): 0.62.2.5.1.2.5 Abrasion Resistance (ASTM D4060): 30 mg/loss.2.5.1.2.6 Gloss (ASTM D523): Minimum 95.

2.5.1.3 Colors: _____.2.5.1.4 Colors: To be selected by Architect from manufacturer's standard colors.2.5.1.5 Colors: As indicated on Drawings.2.5.1.6 Thickness: 15 mil (0.38 mm).2.5.1.7 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.5.1.8 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.5.2 Clear Gloss Urethane Coating:2.5.2.1 Basis of Design: Dex-O-Tex Aero-Flor 100 Clear Gloss by Crossfield Products.2.5.2.2 Physical Properties:

2.5.2.2.1 VOC Content: 100 g/L.2.5.2.2.2 Tensile Strength (ASTM C307): 8,600 psi (5.93 MPa).2.5.2.2.3 Elongation (ASTM D882): 10 percent.2.5.2.2.4 Coefficient of Friction (ASTM F1679): 0.62.2.5.2.2.5 Abrasion Resistance (ASTM D4060): 30 mg/loss.2.5.2.2.6 Gloss (ASTM D523): Minimum 95.

2.5.2.3 Color: Clear.2.5.2.4 Thickness: 15 mil (0.38 mm).2.5.2.5 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.5.2.6 Vapor Control Primer Membrane: Type recommended by flooring manufacturer



2.5.3 High Performance Polyurethane Topcoat:2.5.3.1 Basis of Design: Dex-O-Tex HPT by Crossfield Products.2.5.3.2 Color: Clear.2.5.3.3 Physical Properties:

2.5.3.3.1 Solids Content (ASTM D2369): 96 percent.2.5.3.3.2 VOC Content: Less than 50 g/L.2.5.3.3.3 Impact Resistance, Direct and Reverse (ASTM D2794): 160 in/lbs (18.1

Nm).2.5.3.3.4 Pot Life: 45 minutes.2.5.3.3.5 Tensile Strength (ASTM C2370): 5,000 psi (34.5 MPa).2.5.3.3.6 Elongation (ASTM D2370): 4 percent.

09 67 23 -22

2.5.3.3.7 Abrasion Resistance (ASTM D4060): 15 mg/loss.2.5.3.3.8 Gloss (ASTM D2370): Minimum 85.

2.5.3.4 Thickness: 3 to 5 mil (0.076 to 0.127 mm).2.5.3.5 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.5.3.6 Vapor Control Primer Membrane: Type recommended by flooring manufacturer



2.5.4 Polymeric Floor Coating:2.5.4.1 Basis of Design: Dex-O-Tex Quik-Glaze by Crossfield Products.2.5.4.2 Color: Clear.2.5.4.3 Colors: _____.2.5.4.4 Colors: To be selected by Architect from manufacturer's standard colors.2.5.4.5 Colors: As indicated on Drawings.2.5.4.6 Physical Properties:

2.5.4.6.1 Tear Strength, Die C (ASTM D624): 879 psi (6.06 MPa).2.5.4.6.2 Flexibility, 180 degree bend, 1/8 inch Mandrel (ASTM D1737): Pass.2.5.4.6.3 Tensile Strength (ASTM D412): 2,400 psi (16.5 MPa).2.5.4.6.4 Abrasion Resistance (ASTM D4060): 8 mg/loss.2.5.4.6.5 Impact Resistance, Direct and Reverse (ASTM D2794): 160 in/lbs (18.1

Nm).2.5.4.6.6 Elongation (ASTM D412): 100 percent.2.5.4.6.7 Surface Hardness (ASTM D2240) 90 Durometer "A".2.5.4.6.8 Solids Content by Weight (ASTM D523): 90 percent.2.5.4.6.9 Coefficient of Friction (ASTM D2047): 0.67 dry, 0.82 wet.2.5.4.6.10 Chemical Resistance, 24 Hour Immersion (ASTM D543):

2.5.4.6.10.1 Citric Acid, 1 Percent: No Attack, 5 percent weight change.2.5.4.6.10.2 Lactic Acid, 10 percent: Deglossed but no physical attack, 17

percent weight change.2.5.4.6.10.3 Sulfuric Acid, 10 Percent: No Attack, 6 percent weight change.2.5.4.6.10.4 Sulfuric Acid, 30 Percent: Chemical Damage, 100 percent weight

change.2.5.4.6.10.5 Isopropyl Alcohol, 99 Percent: Chemical Damage, 90 percent

weight change.2.5.4.6.10.6 Sodium Hydroxide, 10 Percent: No Attack, 2 percent weight

change.2.5.4.6.10.7 Sodium Carbonate, 2 Percent: No Attack, 5 percent weight

change.2.5.4.6.10.8 Sodium Hydrochlorite, 5 Percent: No Attack, 3 percent weight

change.2.5.4.6.10.9 Mineral Oil: No Attack, less than 1 percent weight change.2.5.4.6.10.10 Vegetable Oil: No Attack, less than 1 percent weight change.2.5.4.6.10.11 Aviation Gasoline: No Attack, greater than 10 percent weight

change.2.5.4.6.10.12 Diesel Fuel: No Attack, greater than 4 percent weight change.

2.5.4.7 Thickness: 7 mil (0.178 mm).2.5.4.8 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.5.4.9 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.5.5 Clear Fast-Cure Coating and Topcoat:

09 67 23 -23

2.5.5.1 Basis of Design: Dex-O-Tex Quik-Glaze FC by Crossfield Products.2.5.5.2 Physical Properties:

2.5.5.2.1 Tear Strength, Die C (ASTM D624): 879 psi (6.06 MPa).2.5.5.2.2 Flexibility, 180 degree bend, 1/8 inch Mandrel (ASTM D1737): Pass.2.5.5.2.3 Tensile Strength (ASTM D412): 2,400 psi (16.5 MPa).2.5.5.2.4 Elongation (ASTM D412): 80 percent.2.5.5.2.5 Abrasion Resistance (ASTM D4060): 8 mg/loss.2.5.5.2.6 Impact Resistance, Direct and Reverse (ASTM D2794): 160 in/lbs (18.1

Nm).2.5.5.2.7 Surface Hardness (ASTM D2240) 80 to 85 Durometer "D".2.5.5.2.8 Solids Content by Weight: 99.9 percent.2.5.5.2.9 Gloss (ASTM D523): Minimum 88.2.5.5.2.10 Coefficient of Friction (ASTM D2047): 0.67 dry, 0.82 wet.2.5.5.2.11 Microbial Resistance (ASTM G21): Passes, Rating 1.2.5.5.2.12 Dry Time at 50 Percent RH: Surface Dry 1.5 hours, Hard Dry 2.0 hours.2.5.5.2.13 Pot Life at 50 Percent RH: 20 minutes.

2.5.5.3 Color: Clear.2.5.5.4 Thickness: 7 to 12 mils (0.178 to 0.305 mm).2.5.5.5 Anti-Microbial Additive: Prevents most bacteria, fungi, algae and actinomycetes.2.5.5.6 Waterproofing Membrane: Type recommended by flooring manufacturer for type




2.6 OVERHEAD, PATCHING, AND UNDERLAYMENT SYSTEMS

2.6.1 Trowel Applied Polyacrylate Resin Composition Underlayment:2.6.1.1 Basis of Design: Dex-O-Tex A-81 by Crossfield Products.2.6.1.2 Physical Properties:

2.6.1.2.1 Compressive Strength (ASTM C109): 5,140 psi (35.4 MPa).2.6.1.2.2 Flexural Strength (ASTM C78): 1,268 psi (8.74 MPa).2.6.1.2.3 Flexural Modulus of Elasticity (ASTM C580): 2,415 psi (16.7 MPa).2.6.1.2.4 Indentation (MIL-PRF-3134): 0.005 inch (0.127 mm) maximum.2.6.1.2.5 Impact Resistance (Gardner Impact Tester): No chipping, cracking, or

delamination and not more than 0.014 inch (0.356 mm) indentation.2.6.1.2.6 Adhesion (ACI 503.1): 400 psi (2.76 MPa), 100 percent failure in concrete.2.6.1.2.7 Shear Bond Strength (ASTM C882): 410 psi (2.83 MPa).

2.6.1.3 Thickness: 1/8 to 2 inches (3 to 51 mm).2.6.1.4 Thickness: _____.2.6.1.5 Thickness: As required to provide level floor.2.6.1.6 Thickness: As indicated on Drawings.2.6.1.7 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.6.2 Squeegee Applied Smoothing and Resurfacing Compound for Concrete:2.6.2.1 Basis of Design: Dex-O-Tex A-81 SQ by Crossfield Products.2.6.2.2 Physical Properties:

2.6.2.2.1 Compressive Strength (ASTM C109): 6,000 psi (41.4 MPa).2.6.2.2.2 Tensile Strength (ASTM C307): 900 psi (6.21 MPa).2.6.2.2.3 Flexural Strength (ASTM C580): 1,200 psi (8.27 MPa).2.6.2.2.4 Hardness (ASTM D2240) 70 to 75 Durometer "D".2.6.2.2.5 Adhesion (ASTM D4541): 400 psi (2.76 MPa), 100 percent failure in

concrete.2.6.2.2.6 Indentation (MIL-PRF-3134): 305 psi (2.10 MPa).

09 67 23 -24

2.6.2.2.7 Water Absorption (MIL-PRF-3134): 3.14 percent.2.6.2.2.8 Impact Resistance (Gardner Impact Tester): No chipping, cracking, or

delamination and not more than 0.014 inch (0.356 mm) indentation.2.6.2.3 Thickness: 1/16 to 1/2 inches (3 to 12.7 mm).2.6.2.4 Thickness: _____.2.6.2.5 Thickness: As required to provide level floor.2.6.2.6 Thickness: As indicated on Drawings.2.6.2.7 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.6.3 Cementitious Mortar:2.6.3.1 Basis of Design: Dex-O-Tex High Strength Mortar by Crossfield Products.2.6.3.2 Color: Grey.2.6.3.3 Physical Properties:

2.6.3.3.1 Compressive Strength, 28 Day (ASTM C109): 6,125 psi (42.2 MPa).2.6.3.3.2 Tensile Strength, 28 Day (ASTM C109): 585 psi (4.03 MPa).2.6.3.3.3 Flexural Strength, 28 Day (ASTM C348): 1,400 psi (9.65 MPa).2.6.3.3.4 Shrinkage (ASTM C157) Less than 0.04 percent.2.6.3.3.5 Adhesion (ACI 503.R): 290 psi (2.00 MPa), 100 percent failure in concrete.2.6.3.3.6 Initial Set (ASTM C191): 31 minutes.2.6.3.3.7 Final Set (ASTM C191): 39 minutes.

2.6.3.4 Thickness: 1/16 to 2 inches (1.6 to 51 mm).2.6.3.5 Thickness: _____.2.6.3.6 Thickness: As indicated on Drawings.2.6.3.7 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.6.4 Acoustical Flooring Underlayment:2.6.4.1 Basis of Design: Dex-O-Tex Acousti-Fill by Crossfield Products.2.6.4.2 Physical Properties:

2.6.4.2.1 Compressive Strength (ASTM C109): 250 psi (1.72 MPa).2.6.4.2.2 Hardness (ASTM D2240) 20 Durometer "D", 75 Durometer "A".2.6.4.2.3 Indentation (MIL-PRF-3134, Paragraph 4.7.3): No cracking or loss of bond,

indentation 0.047 inches (1.19 mm).2.6.4.2.4 Adhesion (MIL-PRF-3135, Paragraph 4.5.12): 125 psi (0.86 MPa).2.6.4.2.5 Resistance to Elevated Temp. (MIL-PRF-3135, Paragraph 4.5.5):

Complies.2.6.4.2.6 Density: 60 pcf (9425 N/cu.m).2.6.4.2.7 Weight: 5 psf (0.24 KPa).2.6.4.2.8 Impact Noise Radiation, at 1 inch (25 mm) thickness (ASTM E492): INR 0.2.6.4.2.9 Sound Transmission Class, at 1 inch (25 mm) thick (ASTM E413): STC 51.2.6.4.2.10 Sound Transmission Class, at 1/2 inch (13 mm) thickness over 6 inch (152

mm) thick concrete: STC 49.2.6.4.3 Thickness: 1 inch (25 mm).2.6.4.4 Thickness: _____.2.6.4.5 Thickness: As indicated on Drawings.2.6.4.6 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.6.5 Polymer Concrete Admixture:2.6.5.1 Basis of Design: Dex-O-Tex Contex by Crossfield Products.2.6.5.2 Physical Properties:

2.6.5.2.1 Compressive Strength (ASTM C109): 3,610 psi (24.9 MPa).2.6.5.2.2 Tensile Strength (ASTM C109): 817 psi (5.63 MPa).2.6.5.2.3 Flexural Strength (ASTM C580): 1,425 psi (9.83 MPa).2.6.5.2.4 Water Absorption (MIL-D-3134): Less than 3.5 percent.

09 67 23 -25

2.6.5.2.5 Adhesion (ACI 403): 400 psi (2.76 MPa).2.6.5.3 Crack Isolation/Anti-Fracture Membrane: Type recommended by manufacturer


2.6.6 Flexible Polymer Modified Cementitious Repair Mortar and Underlayment:2.6.6.1 Basis of Design: Dex-O-Tex G-26 Underlayment and Repair Mortar by Crossfield

Products.2.6.6.2 Physical Properties:

2.6.6.2.1 Compressive Strength (ASTM C109): 2,115 psi (14.6 MPa).2.6.6.2.2 Tensile Strength (ASTM C307): 925 psi (6.38 MPa).2.6.6.2.3 Flexural Strength (ASTM C580): 2,415 psi (16.7 MPa).2.6.6.2.4 Flow at Elevated Temp. 300 degrees F (149 degrees C) for 4 hours: None.2.6.6.2.5 Corrosive Effect on Aluminum or Steel: None.2.6.6.2.6 Adhesion at up to 1/8 inch (3 mm) thick: 192 psi (1.32 MPa).2.6.6.2.7 Adhesion at up to 1/4 inch (6 mm) thick: 122 psi (0.84 MPa).2.6.6.2.8 Impact Resistance (2 pound (0.91 kg) steel ball dropped from 8 foot (2438

mm) height, samples on steel plate): No cracking or loss of adhesion. Indentation at up to 1/8 inch (3 mm) thick is 0.023 inches (0.58 mm). Indentation at up to 1/4 inch (6 mm) thick is 0.048 inches (1.22 mm).

2.6.6.3 Flexible synthetic rubber latex liquid blended with specially formulated cementitious component.


2.6.7 Polymerized Cementitious Self-Leveling Underlayment:2.6.7.1 Basis of Design: Dex-O-Tex SLU-50 by Crossfield Products.2.6.7.2 Physical Properties:

2.6.7.2.1 Compressive Strength, 28 Days: 4,600 psi (31.7 MPa).2.6.7.2.2 Tensile Strength, 28 Days: 390 psi (2.69 MPa).2.6.7.2.3 Taber Abrasion Resistance: 0.24 percent.2.6.7.2.4 Shrinkage After 28 Days: 0.046 percent.2.6.7.2.5 Absorption (21 days immersion in water): Less than 2 percent.

2.6.7.3 Waterproofing Membrane: Type recommended by manufacturer for type of service and floor condition indicated.


3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin preparation and installation until substrates are properly constructed and inspected complying with ACI 311.4R-05 Guide for Concrete Inspection. The General Contractor is to correct non-conformities if defects are discovered. Repair per ACI 546.R-04. Turn over work in broom clean condition free of debris and foreign matter.3.1.1.1 Substrate Inspection is to be performed by a certified SSPC CCI Inspector.

3.1.2 If substrate preparation is responsibility of another contractor, inspect per ACI 311.4R-05 Guide for Concrete Inspection by a certified SSPC CCI inspector. If preparation is not satisfactory or if surface is contaminated, notify Architect in writing. Do not proceed with the installation before the deficiencies have been satisfactorily corrected.

3.1.3 Perform moisture testing per ASTM F1869 and F2170. Document results per this specification. If MVER or RH exceeds manufactures recommend level for specified product. Apply vapor control primer before proceeding.

3.2 PREPARATION

09 67 23 -26

3.2.1 Clean surfaces thoroughly prior to commencement of the preparation and installation.

3.2.2 Prepare surfaces using methods recommended by manufacturer for achieving best result for substrate under project conditions.

3.2.3 Concrete Surfaces: Shot-blast, or diamond grind per SSPC SP-13/NACE 6. Remove material to provide a sound surface free of laitance, glaze, efflorescence, bond inhibiting curing compounds or form release agents. Remove grease, oil, and other penetrating contaminates. Repair damaged and deteriorated concrete to acceptable condition per ACI 546.R-04. Produce a surface profile equal to ICRI 310.25 CPS 2, CPS 3, or CPS 4. Leave surface free of dust, dirt, laitance, and efflorescence.

3.2.4 Verify proper surface profile per ICRI 310.25 CSP coupons. Perform water break test and tape dust cleanliness test per ISO 8502-3 to determine surface is acceptable to proceed.

3.3 INSTALLATION

3.3.1 Apply Flooring System components according to manufacturer's written instructions. Produce a uniform, monolithic wearing surface of thickness, color and texture indicated.3.3.1.1 Coordinate application of components. Provide optimum adhesion of coatings to

substrate, and optimum intercoat adhesion.3.3.1.2 Cure coatings per manufacturer's written instructions. Prevent contamination

during application and curing processes.3.3.1.3 Expansion and Isolation Joint Treatment: At substrate expansion and isolation

joints, comply with resinous flooring manufacturer's written instructions.3.3.1.4 Contractor shall keep daily logs recording the work performed and environmental

conditions as required by the materials manufacturer.

3.3.2 Vapor Control Primer Membrane: Apply over prepared substrate at required spreading rate.

3.3.3 Crack Isolation/Anti-Fracture Membrane: After Surface Preparation, route out cracks greater than 60 mils. Vacuum cracks and surrounding surface. Remove dust and debris. Fill cracks with flexibilized epoxy membrane. Strip with fabric reinforcement 2 inches (51 mm) on both sides of cracks or per manufacturer's recommendations.3.3.3.1 Application Location: Substrate cracks.3.3.3.2 Application Location: Entire substrate surface.

3.3.4 Waterproofing Membrane: Apply manufacturers recommended waterproof membrane at the required thickness to the area of work and up vertical surfaces to the height of the floorings integral cove base or a minimum of 2 inches (51 mm). Provide fabric reinforcement at all vertical horizontal transitions.3.3.4.1 Application Location: Where indicated on Drawings.3.3.4.2 Application Location: Over entire substrate surface.3.3.4.3 Application Location: ________.3.3.4.4 Membrane Thickness: 30 mils (0.762 mm).3.3.4.5 Membrane Thickness: 40 mils (1.016 mm).3.3.4.6 Membrane Thickness: Manufacturer's recommended thickness.

3.3.5 Divider and Control Joint Strips:3.3.5.1 Place divider strips in accordance with patterns detailed in the drawings.3.3.5.2 Place control joint strips at all control joint locations.3.3.5.3 Set strips into epoxy adhesive without voids present below the strips.

3.3.6 Integral Cove Base: Apply to vertical surfaces. 5/8 inch (16 mm) min. radius and as detailed in Drawings. Apply per manufacturer's recommendations when no details are provided.3.3.6.1 Integral Cove Base: 4 inches (100 mm) high.3.3.6.2 Integral Cove Base (in/mm): ________.

09 67 23 -27

3.3.6.3 Apply waterproofing membrane to all integral cove base substrates.

3.3.7 Self-Leveling Body Coats: Apply in thickness indicated for flooring system.3.3.7.1 Aggregates: Broadcast aggregates at rate recommended by manufacturer. After

resin cures, remove excess aggregates. Provide surface texture indicated.

3.3.8 Troweled or Screeded Body Coats: Apply in thickness indicated. Hand or power trowel and grout to fill voids.

3.3.9 Grout Coat: Apply type recommended by resinous flooring manufacturer, to fill voids in final body coat surface.

3.3.10 Top Coat: Cheminert Clearsealer. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.11 Top Coat: Decor-Flor. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.12 Top Coat: Tek-Crete Sealer CP. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.13 Top Coat: Posi-Tred CR Clear Amber. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.14 Top Coat: Posi-Tred CR Pigmented. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.15 Top Coat: Posi-Tred O Pigmented. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.16 Top Coat: Quik-Glaze FC Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.17 Top Coat: Quik-Glaze Clear Gloss. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.18 Top Coat: Quik-Glaze Pigmented. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.19 Top Coat: Aero-Flor 100 Clear Gloss. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.20 Top Coat: Aero-Flor 100 Pigmented. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.21 Top Coat: HPT. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.22 Top Coat: Electro-Flor CD. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.3.23 Top Coat: Conductive Chem Rez M. Apply in number indicated for flooring system and at spreading rates recommended by manufacturer to produce wearing surface indicated.

3.4 CLEANING AND PROTECTION

3.4.1 Clean products after 96 hours cure in accordance with the manufacturer's recommendations.

09 67 23 -28

3.4.2 Prohibit foot and wheel traffic over flooring for 24 hours. Light foot traffic is acceptable after 24 hours. Normal traffic after 48 hours.

3.4.3 Do not expose to harsh chemicals until full 7 days cure.

3.4.4 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

09 67 23 -29

€¦ · web viewsulfuric acid, 30 percent: no effect. thickness: 3/16 to 1/4 inch (5 to 6 mm)....

Documents