KVS-TT-280 tripod turnstile

Operation & Maintenance Manual---KVS-TT-280 tripod turnstile

Version V8.1

KVS-TT-280 tripod turnstile

1.Introduction1.1General

Please read this manual carefully, it contains information that will assist you with all aspects of

installation and Maintenance including unpacking. Correct installation & Maintenance will ensure

smooth functionality and increase the life-span of components.

KAVASS security tech limited makes every effort to ensure that this manual is reviewed

whenever significant changes are made to the design. However, our policy of continuous

improvement may result in some small differences between the unit supplied and the description

in this document.

Enquiries in this respect should, in the first instance, be directed to our Technical Department.

Telephone +86 (571) 88790663, E-mail Kavasssupport01@ikavass.com

1.2Electrical WarningsThe electrical power used in this equipment is at a voltage high enough to endanger life. Before

carrying out maintenance or repair, you must ensure that the equipment is isolated from the electrical

supply and tests made to verify that the isolation is complete.

When the supply cannot be disconnected, functional testing, maintenance and repair of the

electrical units is to be undertaken only by persons fully aware of the danger involved and who have

taken adequate precautions and training.

1.3ErrorsReports on errors, comments and suggestions concerning this manual are requested and

encouraged. They should be submitted to:

Technical Department, KAVASS SECURITY TECH LIMITED

6th F, T5 EFC, 89# Lianchuang St.,Yuhang Dist., Hangzhou Zhejiang China.

Telephone +86 (571) 88790663.

E-mail Kavasssupport01@ikavass.com

1.4Good PracticesEquipment being installed must not be left unattended unless all potential mechanical and

electrical hazards have been made safe. A competent person must be left in charge when the

equipment is to be left while potentially unsafe.

The following points indicate good practice that will contribute to safety and avoid equipment

damage.

Ensure that all electrical power supplies are turned OFF and disconnected before working on

KVS-TT-280 tripod turnstileany of the equipment.

Never leave the equipment in a potentially dangerous state.

Use only the correct tools for the task in hand.

When working on the equipment, remove any personal jewellery that may be conductive, or

clothing that may become entangled with mechanical parts.

1.5Equipment Safety SystemsSafety systems and controls, such as interlocks, covers and guards, must not be overridden or

bypassed by personnel other than authorised staff who are qualified to carry out prescribed actions

within specified Warnings.

1.6Important notice

KVS-TT-280 is a security product; any children or minors using the automatic tripod turnstile must

be supervised and accompanied by a responsible adult. KAVASS SECURITY TECH LIMITED does not

accept any liability if this rule is not enforced.

2. Product Description2.1 Brief Introduction KVS-TT-280 Full-automatic tripod turnstile is a kind of 2-way speed access control equipment

designed for places with security requirements. It can be easily integrated with IC card, ID card, two-

dimensional code, fingerprint, face recognition and other identification equipment, can achieve the

channel of intelligent, efficient management.Full-automatic tripod turnstiles are fully applicable to a

high traffic flow places like school, station, airport,subway ,office building, scenic spot and other

places.

2.2 Functions & Features Varied pass mode can be chosen flexibly.

• Unlock Mode. - All persons are allowed transit.

• Lock Mode. - Transit is forbidden.

• Reader Control Mode. - Transit is only allowed for persons who have been given permission

by a badge reader.

Standard signal input port(Relay signal input), can be connected with most of the access control

board, fingerprint device and scanner and so on.

The turnstile has automatic reset function, if people swipe the authorized card, but don’t pass

through within the settled time, it need to swipe card again for entry.

Card memory function can be set.

Conten ts

In tr oduc

tio

Instruc

tions

f oruse

Technica

l Information

I

n

st

a

ll

a

ti

o

n

KVS-TT-280 tripod turnstile Arm automatically lock when in forced push without permissions, and automatic reset function.

Highlight LED indicator , displaying passing status.

When power off or emergency signal input, the arm fall down automatically.

Self diagnostic and alarm function for convenient maintenance and use.

2.3 Technical SpecificationItem Description

Cabinet 304 stainless steel

Reliability of the core 3million, no fault

Weight 55Kg(bridge type)

Arm length 510(mm)

Max thrust capacity 60Kg

Driving force of arms 3Kg

Driving mode digital

Direction of rotation Unidirectional/ Bidirectional (controllable)

Indicator lamp Green means passage

Power supply for core： AC220V ±10％（AC24V,DV12V）Voltage of drop arm device: DC12V ±5％Method of arm dropping It will drop when the electricity is cut off.

Method of positioning the lock arm: It can be positioned manually or automatically.

Operational voltage DC 24V ±5％Voltage of indicator lamp： DC12V ±5％(standard)

Power consumption 10W

Working environment Indoors or outdoors(outdoor is optional)

Working temperature -30℃～60℃

Humidity 5％～90％Waterproof IP31≧

Installation interfaces for card readers： 2

Control interface relay signal input

Time needed for opening 0.2 seconds

Passing speed 30~45 persons/min

3. Install Instruction3.1 Unpacking

Product Description

KVS-TT-280 tripod turnstileOn receipt of the KVS-TT-280 tripod turnstile,pls check all items are delivered complete and

undamaged. If for any reason transit damage has occurred, ensure the extent of any damage is

recorded and if considered necessary, report the incident to KAVASS SECURITY TECH LIMITED.

Electrical installation must be carried out by authorised staff. The placing, installation and

specifications of all cables must comply with the instructions given in this document.

KAVASS SECURITY TECH LIMITED does not accept responsibility for any injury or damage incurred

due to departure from the instructions in this Technical Manual.

3.2 Tools Required

1 A set of hexagon spanner 5Screw driver and other common wiring

tool

2 Cross screwdriver 6mm 6 Millimeter

3 Open spanner 17-19mm 7 M12x100 Expansion screws 8pcs

4

Impact drill(including D16 and

D14 drills)8 Cable Tester

3.3 Electrical Connections Before installation, below the turnstile installed position need embed two tube , one is 220V,3 x 1.5

single-phase power lines ,the other is 4 x 0.5 shielding line.Pls refer to below drawing PIC9.1

PIC9.13.4 Unit PositioningThe following guidelines are given to ensure that the unit is positioned correctly.

KVS-TT-280 tripod turnstile Mark the floor fixing positions carefully as shown on following drawing PIC9.2 and check the

conduit risers are correct.

Stand the unit over the marked positions and check that the bolt and conduit holes in the base of

the unit match the floor markings.

Check all clearances to adjoining turnstile or Wall.

PIC9.23.5 Floor Drilling

When satisfied that all is correct, move the unit away and drill the floor. Fit the anchor bolts.

3.6 Installation Re-position the units and anchor them to the floor by means of the anchor fixings.

Make sure that the frame is perfectly level, checking in transverse and longitudinal direction, use

shims and all other necessary measures to obtain the required result.

In the open position the edge of the wing must be parallel with the casework.

4.Board and parameter instruction4.1 Board instruction

KVS-TT-280 tripod turnstile

4.1.1 Port instructionNo. Port Sign Instructions

1 VDD +12V power Output

2 BUTT Manual button for arm drop down

3 OP-L +12 V Entry opening signal input

4 CNT-L +12 V Entry counter signal output

5 DIR-L12V power Output to Light bar, counter and so on

6 GND

7 +24V Output for entry square solenoid, normally 0v t, when board recieve open

singal,This port will be 24v output8 LOCK1

KVS-TT-280 tripod turnstile

9 +24V Output for exit square solenoid, normally 0v t, when board recieve open

singal,This port will be 24v output10 LOCK2

11 +24V+24 V power supply for arm drop down circular solenoid

12 LOCK3

13 PCAC18V/24DC

14 PD

15 VDD +12V power Output

16 CUI-R Reset switch

17 OPE-R +12 V Exit opening signal input

18 CNT-R +12 V Exit counter signal output

19 DIR-R12V power Output to Light bar, counter and so on

20 GND

21 TA/RX 485 communication TA

22 TB/TX 485 communication TB

4.1.2 Push button instructionNo. Item Instructions

1 In test Left way test

2 Out Test Right way test

3 INC

When it is in the normal working state,press INC,then the left solenoid pull-in;

When it is in programming state,it is used for setting.

Means parameter values plus 1.

4 SET Enter or exitprogramming state

5 DEC

When it is in the normal working state,press INC,then the right solenoid pull-in;

When it is in programming state,it is used for setting.

Means parameter values minus 1.

4.1.3 Light instructionNo. Item Instructions

KVS-TT-280 tripod turnstile

L1Safty fuse

Left way test

L3 Power Supply

L4 Arm drop down

L6 Exit opening

L7 Reset signal

L9 Entry square solenoid power connected

L10 Exit square solenoid power connected

5.Daily maintenance and trouble shooting5.1 General indications The tripod turnstile should be inspected and cleaned at regular intervals in order to maintain the

components in good working order and to check for signs of wear. The following indications refer to

the installation where the average number of transits per year is equal to two million. When the tripod

turnstile is used in a dusty area, the regular interval for inspection should be shortened. If used in the

subway or the light rail station, the inspection interval is recommended to be 6 months. The users are

also encouraged to determine the interval according to their own situation.

To avoid the risk of electric shock, always ensure that the electrical power is disconnected before

inspecting the mechanism.

5.2 ComponentLock arms and solenoids (Operation to be carried out with the power supply disconnected.): —

Grease the pins of the lock arms that slide on the solenoid shaft.—Grease the solenoid shaft and

spring, and do not grease the core of the solenoid—check that the shaft/lock arm assembly moves

freely.

5.3 Oil pressure of the damperOperation should be carried out with the power supply disconnected ： --check whether the

damper oil spills; --check whether the force exerted by the spring is enough ； -- The force exerted by

the spring should match that exerted by the damper. Generally speaking, the former need to be

slightly more powerful.

5.4 Upper positioning camOperation should be carried out with the power supply disconnected.—Loosen the spring of the

KVS-TT-280 tripod turnstilepositioning lever.—Check the guide way in the cam is clean and not excessively worn. –check some

metal powder or the like sticks to the solenoid—Check the guide pin of the positioning lever for

excessive play.—Check the magnetic strip is perfectly attached to the edge of the cam——Refit the

cam -- adjust the spring of the positioning lever.

5.5 Tripod Operation should be carried out with the power supply disconnected. Check tightness of the three

securing the base plate to the mechanism shaft.

5.6 Emergency Drop Arm DeviceClean all dust from the arm detents, the arm drop lever and the relative solenoid. Do not lubricate

these parts.

5.7 Cable and ConnectorsOperation should be carried out with the power supply disconnected：

--Check that the wire connectors are firmly attached.

--Check that the terminals are fully tightened.

--Check that the insulation of the wires is in good condition and that no conductors are exposed.

5.8 Tips and trouble shooting:Q1: Passing two or three people after swipe card at a time.

Reasons: 1. The limited switch didn’t be touched by the right screw cap when the turn plate rotating.

(Or didn’t receive the effective signal even touched)

2. The access controller set delay time, when the driver board received the close signal, which the gate

will waiting for delay time over, then close gate.

3. The middle lock arm of square solenoid got stuck, then flexing insensitively

4. The driver board fault.

Solution: 1.Adjusting the position of limited switch and the right screw cap, made both of them can

connected.(Checking the circuit of limited switch or change the limited switch)

2. Setting the delay time to 0

3. Changing the square electromagnet.

4. Changing the driver board.

Q2: Got chuck when rotating to the half way.

Reasons: That drop arm device is effect turn plate move route.

KVS-TT-280 tripod turnstileSolution：1. Checking if the screw of boom support is loose, if yes, should raise it up by hand,Then put

it in the middle position and tightening.

2. Checking if whether the solenoid of drop arm attract the below plate or not, if didn’t, need to adjust

upper the below plate manually, making the solenoid attract the plate (If manual adjusted failed.

Firstly, checking if there have clutter between the solenoid and the below plate patch so that informed

a gap. As won’t attract closely if exist gap; Second, checking if the solenoid wire has been correct

connected and if have something damage of electromagnet. )

3. The screw didn’t loose and the solenoid attracts with below plate, which need to tightening, then

doing according to first step.

Q3:Didn’t drop arm automatically when power failure

Reasons: The drop arm device is putting too high so that the solenoid attracts plate, which button can

not press arm lock parts.

Solution: Firstly, adjusting drop arm device upper by hand, making the solenoid attract plate, then

unscrew the four screws on the drop arm device and press them down (normally attach the arm lock

parts is ok),at last , tightening the screw and circle dropout test.

Q4:The arm won’t operate when power on.

Reasons: 1. The drop arm device is putting too high, raising the arm up by manual, but arm lock will

push drop arm device bottom, but solenoid can’t reach to the position which attract plate.

2.The drop arm device is putting too low, raising the arm up by manual, the arm lock will push drop

arm device bottom, after solenoid attract plate, the arm haven’t be fixed to the balance position, so

the bottom of drop arm device pressed the arm lock ,can’t be closed.

Solution: Firstly, pressed the bottom of drop arm device ,making the solenoid attracts plate, then

loosen the four screws which are fixed on the drop arm device, the reasons to made the situation is

that the drop arm device so high or too low. So that need to adjust the drop arm device to a suit

position.

Q5: The arm device is not vertical.

Reasons: The drop arm device is putting too low, when power off, the circle solenoid desorbs

automatically. When drop arm device is downing, which will push arm detent to release lock arm,

during the dropping the lock arm will push-back, when drop arm device at higher position, but arm

bar still no finish drop down, so will not vertical.

Solutions: Loosening the four screws on the drop arm device, then upper the arm manually and

moving it up to the distance which against bar lock from 0.2~0.5mm ,tightening the four screws.

KVS-TT-280 tripod turnstile

Q6:The rotating speed is too slow or fast.

Reasons: Too slow is because the shock absorber over tight, and too fast is too loose.

Solution: Adjusting the shock absorber, if no much effective, will need to check the machine core

spring of positioning lever (which local in near position cam ), whether got chuck or damage, if yes,

will need to change the pedestal.

Q7: The gap between turnplate and housing is bigger

Reasons:1.The screws which used to fix the machine core is loose, making fall down.

2.The shaft of machine core loose weld and nut is loose.

3.The screws which used to fix turn plate is loose, making fall down.

Solutions: 1.Raising the machine core up to the position which the distance between turn plate and

machine body is from 1mm to 3mm,then tightening the screws.

2. Twisting down the three screws which used to fix turn plate, taking the screws out and tightening

the circle nut which under the machine core, adding the screw glue and fixed the turn plate again.

3. Tightening directly the screws which used to fix the turn plate.

Q8: Other questions

Solution: Changing the driver PCB board or other spare parts, like electric leakage, which need to

change transformer, or power supply, and so on.

Date of delivery Turnstile model

KVS-TT-280 tripod turnstile

Maintain record

Service

Dates

Trouble descriptions Solution Service People Sign and

stamp