LEED Report6/3/2010

Project Name:   Created By:   Project Location:   Firm/Company Name:  

This document contains sustainability information for the following USG product(s):

• Aspen ceiling panel   Item Number: 650• Astro ClimaPlus ceiling panel   Item Number: 8122• Brio ClimaPlus ceiling panel   Item Number: 308• Clean Room ClimaPlus ceiling panel   Item Number: 56091• Clean Room ClimaPlus 10M-100M ceiling panel   Item Number: 56060• Eclipse ClimaPlus ceiling panel   Item Number: 70073• Eclipse ClimaPlus Illusions and Pedestals ceiling panel   Item Number: 72015• F Fissured ceiling panel   Item Number: 101• Fissured ceiling panel   Item Number: 506• Fresco ClimaPlus ceiling panel   Item Number: 608• Frost ceiling panel   Item Number: 400• Frost ClimaPlus ceiling panel   Item Number: 414• Frost ClimaPlus High-NRC, High-CAC ceiling panel   Item Number: 484• Glacier ceiling panel   Item Number: 701• Halcyon ClimaPlus ceiling panel   Item Number: 88221• Halcyon ClimaPlus Planks and Large Sizes ceiling panel   Item Number: 98445• Mars ClimaPlus ceiling panel   Item Number: 86185• Mars Climaplus High NRC ceiling panel   Item Number: 86100• Millennia ClimaPlus ceiling panel   Item Number: 70003• Millennia ClimaPlus High NRC ceiling panel   Item Number: 76201• Olympia Micro ClimaPlus ceiling panel

   Item Number: 4211• Pebbled ClimaPlus ceiling panel   Item Number: 4800• Premier Hi-Lite ClimaPlus ceiling panel   Item Number: 7050G• Premier Nubby ClimaPlus ceiling panel   Item Number: 7000G• Radar ceiling panel   Item Number: 2110• Radar Ceramic ClimaPlus ceiling panel   Item Number: 56644• Radar ClimaPlus ceiling panel   Item Number: 2207• Radar ClimaPlus High CAC, High NRC ceiling panel   Item Number: 22111• Radar ClimaPlus Illusion ceiling panel   Item Number: 2842• Radar Illusion ceiling panel   Item Number: 2742• Rock Face ClimaPlus ceiling panel   Item Number: 55483• Sandrift Climaplus ceiling panel   Item Number: 808• Sheetrock Brand Lay-In Ceiling Panel ClimaPlus ceiling panel   Item Number: 3200• Sheetrock Lay-In Panels ClimaPlus, PVC Free ceiling panel   Item Number: 3220• Summit ClimaPlus ceiling panel   Item Number: 990• Touchstone ClimaPlus ceiling panel   Item Number: 5893 LEED® is a guideline for building solutions established by the USGBC – Products are NOT “LEED certified”, however they can assist in obtaining LEED credits/points for a project.USG Corporation is a founding member of the U.S. Green Building Council.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Aspen #650Edge Type: Shadowline Tapered

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.87Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

16% + 1/2 (13%) x    material cost = 0.225 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.87 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Astro ClimaPlus #8122Edge Type: Square EdgePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.86Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (69%) x    material cost = 0.345 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 3%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.86 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Brio ClimaPlus #308Edge Type: ShadowlinePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.81Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.81 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Clean Room ClimaPlus #56091Edge Type: Square EdgePanel Size: 2' x 4' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.79Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

1% + 1/2 (50%) x    material cost = 0.26 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.79 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Clean Room ClimaPlus 10M-100M #56060Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.79Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

1% + 1/2 (50%) x    material cost = 0.26 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.79 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Eclipse ClimaPlus #70073Edge Type: BESK

Panel Size: 12" x 12" x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.86Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (77%) x    material cost = 0.385 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 1-2%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.86 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.6 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Eclipse ClimaPlus Illusions and Pedestals #72015Edge Type: Pedestals Interline Tapered

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.84Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (77%) x    material cost = 0.385 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 1-2%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.84 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.65 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

F Fissured #101Edge Type: SESK

Panel Size: 12" x 12" x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.79Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.79 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Fissured #506Edge Type: Shadowline Tapered

Panel Size: 2' x 2' x 5/8" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.81Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

17.5% + 1/2 (7.5%) x    material cost = 0.2125 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MSCloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 7%Cloquet, MN - 6-7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.81 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Fresco ClimaPlus #608Edge Type: ShadowlinePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.83Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.83 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Frost #400Edge Type: Pedestals Interline

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.85Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.85 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Frost ClimaPlus #414Edge Type: Shadowline Bevel

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.83Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.83 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Frost ClimaPlus High-NRC, High-CAC #484Edge Type: Shadowline Bevel

Panel Size: 2' x 2' x 7/8" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.88Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.88 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.75 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Glacier #701Edge Type: SESK

Panel Size: 12" x 12" x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.7Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.7 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.65 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Halcyon ClimaPlus #88221Edge Type: Square EdgePanel Size: 2' x 2' x 1"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.88Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

40% + 1/2 (1%) x    material cost = 0.405 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS  

*If more than one location is listed, verify which plant this product comes from. EQ 8.1; Daylight & Views Published Light Reflectance value of 0.88 to extend the daylight effectiveness into the

space. ID 1.1; Innovation Credits NRC value of 0.9 - higher than typical ceiling panels and a lifetime 30 year warranty

which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Halcyon ClimaPlus Planks and Large Sizes #98445Edge Type: Fineline

Panel Size: 4' x 4' x 1" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.88Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

40% + 1/2 (1%) x    material cost = 0.405 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS  

*If more than one location is listed, verify which plant this product comes from. EQ 8.1; Daylight & Views Published Light Reflectance value of 0.88 to extend the daylight effectiveness into the

space. ID 1.1; Innovation Credits NRC value of 0.95 - higher than typical ceiling panels and a lifetime 30 year warranty

which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Mars ClimaPlus #86185Edge Type: Square EdgePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.89Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (76%) x    material cost = 0.38 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 2%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.89 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Mars Climaplus High NRC #86100Edge Type: Square EdgePanel Size: 2' x 2' x 7/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.89Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (77%) x    material cost = 0.385 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 2%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.89 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.8 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Millennia ClimaPlus #70003Edge Type: BESK

Panel Size: 12" x 12" x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.85Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (75%) x    material cost = 0.375 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 1-3%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.85 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.6 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Millennia ClimaPlus High NRC #76201Edge Type: Shadowline Tapered

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.87Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (75%) x    material cost = 0.375 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer%) from Red Wing, MN; 5% polymer emulsion (local), starch (Rapid Renew %) from Clinton, MN; Firecode panels 20% clay from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 1-3%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.87 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.75 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Olympia Micro ClimaPlus #4211Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.87Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

13% + 1/2 (39%) x    material cost = 0.325 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 8%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.87 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Pebbled ClimaPlus #4800Edge Type: Square EdgePanel Size: 2' x 4' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.86Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

17% + 1/2 (17%) x    material cost = 0.255 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 6.5%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.86 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Premier Hi-Lite ClimaPlus #7050GEdge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.76Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

8% + 1/2 (23%) x    material cost = 0.195 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS  

*If more than one location is listed, verify which plant this product comes from. EQ 8.1; Daylight & Views Published Light Reflectance value of 0.76 to extend the daylight effectiveness into the

space. ID 1.1; Innovation Credits NRC value of 0.75 - higher than typical ceiling panels and a lifetime 30 year warranty

which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Premier Nubby ClimaPlus #7000GEdge Type: Square EdgePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.87Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

29% + 1/2 (0%) x    material cost = 0.29 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS  

*If more than one location is listed, verify which plant this product comes from. EQ 8.1; Daylight & Views Published Light Reflectance value of 0.87 to extend the daylight effectiveness into the

space. ID 1.1; Innovation Credits NRC value of 0.85 - higher than typical ceiling panels and a lifetime 30 year warranty

which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar #2110Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.85Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

17.5% + 1/2 (7.5%) x    material cost = 0.2125 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TNGreenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6-7%Greenville, MS - 7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.85 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar Ceramic ClimaPlus #56644Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.82Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (45%) x    material cost = 0.225 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 2%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.82 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar ClimaPlus #2207Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.84Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

14.5% + 1/2 (22%) x    material cost = 0.255 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TNGreenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6-10%Greenville, MS - 7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.84 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar ClimaPlus High CAC, High NRC #22111Edge Type: Square EdgePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.84Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

1% + 1/2 (57%) x    material cost = 0.295 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TN

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 10%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.84 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar ClimaPlus Illusion #2842Edge Type: Shadowline Tapered

Panel Size: 2' x 4' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.84Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

14.5% + 1/2 (22%) x    material cost = 0.255 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TNGreenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6-10%Greenville, MS - 7%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.84 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Radar Illusion #2742Edge Type: Shadowline Tapered

Panel Size: 2' x 4' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.89Luminaires may be reduced to meet required ASHRAE standards.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

17.5% + 1/2 (7.5%) x    material cost = 0.2125 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Cloquet, MN - Mineral wool (Pre-consumer %) from Red Wing, MN, perlite 20-50% from Soccorro, NM; recycled paper (Post-consumer %) local; starch (Rapid Renew %) from Clinton, MN; clay 2-12% from Gleason, TNGreenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Cloquet, MN - 6-7%Greenville, MS - 7%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.89 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Rock Face ClimaPlus #55483Edge Type: Shadowline Tapered

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.86Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

6% + 1/2 (43%) x    material cost = 0.275 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.86 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Sandrift Climaplus #808Edge Type: ShadowlinePanel Size: 2' x 2' x 3/4"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.83Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (71%) x    material cost = 0.355 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 12.5%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.83 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Sheetrock Brand Lay-In Ceiling Panel ClimaPlus #3200Edge Type: Square EdgePanel Size: 2' x 4' x 1/2"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.77Luminaires may be reduced to meet required ASHRAE standards.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (23%) x    material cost = 0.115 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Shoals, IN; Sweetwater, TX; Stony Point, NY; and Plaster City, CA (SHEETROCK Lay-In Ceiling Panel ClimaPlus Clean Room manufactured at Sweetwater, TX only)

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Shoals, IN; Sweetwater, TX; Stony Point, NY; and Plaster City, CA - 1%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.77 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Sheetrock Lay-In Panels ClimaPlus, PVC Free #3220Edge Type: Square EdgePanel Size: 2' x 2' x 1/2"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.85Luminaires may be reduced to meet required ASHRAE standards.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

5% + 1/2 (51%) x    material cost = 0.305 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Shoals, IN  

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Shoals, IN - 9%

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.85 to extend the daylight effectiveness into the space.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Summit ClimaPlus #990Edge Type: Shadowline Bevel

Panel Size: 2' x 2' x 3/4" 

Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.81Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Zero-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Class A

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

0% + 1/2 (63%) x    material cost = 0.315 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Walworth, WI - Slag wool (Pre-consumer %) made onsite, slag within 100 miles, starch (Rapid Renew %) from Clinton, IA; Class A panels 10% plaster of paris East Chicago, IN; Firecode panels 14% clay from Macon, GA

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Walworth, WI - 11%

EQ 3.2; CHPS Pass/Zero EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.81 to extend the daylight effectiveness into the space.

ID 1.1; Innovation Credits NRC value of 0.7 - higher than typical ceiling panels and a lifetime 30 year warranty which may provide innovation credits in acoustical performance.

  LEED Report

Acoustical Ceiling Panels

6/3/2010

The following lists several LEED® prerequisites and information about the USG product you are specifying that may assist you in obtaining LEED credits.

Touchstone ClimaPlus #5893Edge Type: Square EdgePanel Size: 2' x 2' x 5/8"

  Possible LEED Credit: EA 1; Optimize Energy Performance

Published Light Reflectance value of 0.86Luminaires may be reduced to meet required ASHRAE standards.

IEQ 3.1 & 3.2 IAQ; Management Plan

Low-Emitting panels can help qualify for LEED credits.

MR 2.1 & 2.2; Construction Waste Management

USG offers an Acoustical Ceilings Recycling Program for qualified renovation projects. Mineral fiber ceiling panels may qualify for recycling.

MR 4.1 & 4.2; RecycledContent (% by weight)

Firecode

Post-Consumer   Pre-Consumer Material Cost   Total Combined Value

5% + 1/2 (43%) x    material cost = 0.265 x material cost

MR 5.1 & 5.2; Regional Materials

This product is manufactured in the following locations:Greenville, MS - Mineral wool (Pre-consumer %) railed from Red Wing, MN; perlite 20-50% railed from Soccorro, NM; Recycled paper (Post-consumer %) from Senatobia, MS; Starch (Rapid Renew %) from Decatur, AL; and clay 2-12% from Crenshaw, MS

*If more than one location is listed, verify which plant this product comes from. MR 6; Rapidly Renewable Materials

Greenville, MS - 7%

EQ 3.2; CHPS Pass EQ 4; Low-Emitting Materials Pre-finished acoustical ceiling panels meet CA/DHS/EHLB/R-174 requirements for

emissions of Toxic Volatile Organic Chemicals (VOCs) for use in the Collaborative of High Performance Schools (CHPS).

EQ 8.1; Daylight & Views Published Light Reflectance value of 0.86 to extend the daylight effectiveness into the space.

  LEED Report

6/3/2010

Test Protocols & Definitions

Recycled Content (Post-Consumer & Post-Industrial) per Federal Trade Commission Environmental Marketing Guides. Recycled-content products may contain some pre-consumer waste, some post-consumer waste or both. A product does not have to contain 100 percent recovered materials to be considered "recycled," but the higher the percentage of recycled content, the greater the amount of waste that is diverted from disposal.

Post-Industrial (Pre-Consumer) materials are generated by manufacturers and processors, and may consist of scrap, trimmings and other by-products that were never used in the consumer market. Post-Industrial and Pre-Consumer are one in the same under the USGBC LEED_ rating systems.

Post-Consumer material is an end product that has completed its life cycle as a consumer item and would otherwise have been disposed of as a solid waste. Post-consumer materials include recyclables collected in commercial and residential recycling programs, such as office paper, cardboard, aluminum cans, plastics and metals.

LR (Light Reflectance) tested per ASTM C1477

NRC (Noise Reduction Coefficient) tested per ASTM C423

CAC (Ceiling Attenuation Class) tested per ASTM 1414

TVOC (Total Volatile Organic Compound) emission measured per ASTM D 5116, State of Washington allows for 500 ug/m3

CHPS (Collaborative for High Performance Schools) follow EPA Section 01350 for VOC emission and determination on PASS.

Formaldehyde emissions measured during CHPS testing per Section 01350, for most products CHPS allows 13.5 ppb & state of Washington allows for 50 ppb.

Zero emissions is defined as the quantity less than test chamber background concentrations as required by Section 3.8.4.2 of the "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers, Supercedes previous versions of small-scale environmental chamber testing portion of California Specification 01350, July 15, 2004." Section 3.8.4.3 states "Background concentrations in the empty chamber ventilated at 1.0 air changes per hour shall not exceed 2 _g m-3 for any individual VOC, and 25 _g m-3 for TVOC."

  LEED Report

6/3/2010

LEED Credits

LEED® is a guideline for building solutions established by the USGBC – Products are NOT “LEED certified”, however they can assist in obtaining LEED credit/points for a project.

Energy & AtmosphereEA Credit 1 – Optimize Energy PerformanceHigh light reflectance (LR) of ceiling materials can reduce required luminaires of design space as required per ASHRAE and reduce the number of light fixtures needed, curbing energy consumption.

Materials & ResourcesMR Credit 2 – Construction Waste Management: Divert From Disposal2.1 – Divert 50% of project waste (by weight) from landfill2.2 – Divert another 25% of project waste (by weight) from landfillMR Credit 3 – Materials ReuseProducts may contain synthetic material and metal ceilings/components may include recycled aluminum3.1 – 5% of total materials use salvaged, refurbished, or reused materials (based on cost)3.2 – 10% of total materials use salvaged, refurbished, or reused materials (based on cost)MR Credit 4 – Recycled Content4.1 – 10% of project materials’ value (Post-Consumer + _ Post-Industrial)4.2 – 20% of project materials’ value (Post-Consumer + _ Post-Industrial)MR Credit 5 – Local/Regional Materials: Extracted, Processed & Manufactured Regionally5.1 – 10% of raw materials for above products obtained within 500 miles5.2 – 20% of raw materials for above products obtained within 500 milesMR Credit 6 – Rapidly Renewable MaterialsProducts may contain corn/ wheat starch binders, renewable alternatives to petroleum-based binders

Indoor Environmental QualityEQ Credit 4 – Low-Emitting Materials4.1, 4.2, 4.3, 4.4 – Products emit no formaldehyde or only a very low amountEQ Credit 8 – Daylight and Views8.1, 8.2 – High LR can improve the quality and quantity of natural light by enhancing indirect lightingEQ Credit 9 – Enhanced Acoustical PerformanceProducts used in tested assemblies may reduce sound transmission in spacesEQ Credit 10 – Mold PreventionProducts may contain ingredients that reduce the potential growth of mold

InnovationID Credit 1 – InnovationExceptional performance above LEED requirements can be awarded extra points

  LEED Report

6/3/2010

Resources

USGwww.usg.comwww.usgdesignstudio.comwww.sustainableceilings.comCustomer Service: (800) 950-3839

OTHERhttp://www.usgbc.orghttp://www.uli.orghttp://www.chps.nethttp://www.chps.net/manual/lem_table.htmhttp://www.ashrae.org/http://www.scscertified.com

For additional information or assistance, please contact: Your local USG architectural rep or USG4YOU at (800) 874-4968

©2009 United States Gypsum CompanyPrinted in U.S.A.

Manufactured byUSG Corporation550 West AdamsChicago, IL 60661