we are available 24/7...ball valves 2-piece bronze standard port ba-100 / ba-100s 600 wog 150 swp,...
TRANSCRIPT
Physical Address 1509 Riverport RoadKingsport, TN 37660
Physical Address 400 Natalie Boulevard
Loudon, TN 37774
Kingsport TN: 423-765-9991 | Loudon TN: 865-458-2333
FOR QUESTIONS OR TO REQUEST A QUOTE, VISIT WWW.PROCESSSUPPLY.COM OR CALL
W E A R E A V A I L A B L E 2 4 / 7
B A L L VA LV E S
2-PIECE BRONZEStandard Port
BA-100 / BA-100S600 WOG 150 SWP, MSS SP-110, Threaded, BA-100S with Stainless Steel Ball and Stem 1/4" thru 3"
BA-100ELD / BA-100SELD125 psig, MSS SP-110, Latch Lock Handle, Threaded with Exhaust Port, BA-100SELD with Stainless Steel Ball and Stem1/4" thru 2"
BA-100M600 WOG 150 SWP, MSS SP-110, Male x Female 1/4" thru 2"
BA-100 P2 / BA-100S P2200 psig @ 250°F, MSS SP-110, Press X Press, BA-100S P2 with Stainless Steel Ball and Stem 1/2" thru 2"
BA-150 / BA-150S600 WOG 150 SWP, MSS SP-110, Solder, BA-150S with Stainless Steel Ball & Stem3/8" thru 3"
Full Port
BA-100H 600 WOG, MSS SP-110, Threaded With Hose, Cap and Chain1/2" and 3/4"
BA-150H600 WOG, MSS SP-110, Solder With Hose, Cap and Chain 1/2" and 3/4"
BA-100H P1 / BA-100SH P1200 psig @ 250°F, MSS SP-110, Press X Hose, BA-100SH P1 with Stainless Steel Ball & Stem 1/2" and 3/4"
continued
2-PIECE BRONZEFull Port
BA-400 / BA-400S600 WOG 150 SWP, MSS SP-110, Threaded, BA-400S with Stainless Steel Ball & Stem1/4" thru 2"
BA-400 P2 / BA-400S P2200 psig @ 250°F, MSS SP-110, Press X Press, BA-400S with Stainless Steel Ball & Stem1/2" thru 2"
BA-400S3600 WOG, 250 SWP, MSS SP-110, Stainless Steel Ball & Stem, Threaded, Steam Seats 1/2" thru 2"
BA-450 / BA-450S600 WOG, 150 SWP, MSS SP-110, Solder, BA-450S with Stainless Steel Ball & Stem3/8" thru 2"
2-PIECEBRONZE LEAD-FREEBRONZE BALL VALVESFOR POTABLEWATER SERVICE*Standard Port
UPBA-100 / UPBA-100S 600 WOG, MSS SP-110, Threaded, UPBA-100S with Stainless Steel Ball & Stem1/4" thru 3"
UPBA-100 P2 / UPBA-100S P2200 psig @ 250°F, MSS SP-110, Press X Press, UPBA-100S with Stainless Steel Ball and Stem1/2" thru 3"
BA-100TIH
BA-100 P2
* Meets Senate law S3874. IAPMO tested and certified to NSF/ANSI 372 for “lead-free” compliance.
BA-450
UPBA-100 P2 XH
BA-100 P2 TIH
BA-150H
Options/AccessoriesBA-100/150 / UPBA-100/150INSULATOR Handle (TIH)Oval Handle (OH)Locking Oval Handle (LO)Stainless-Steel Handle (SH)Tee Handle (TH)Locking Handle (LD)Extension Handle (XH)Extension Handle w/Memory Stop (XM)Memory Stop (MS)Chain Lever (CL)
Options/AccessoriesBA-100/150 / UPBA-100/150BA-400/450 / UPBA-400/450 INSULATOR Handle (TIH)Oval Handle (OH)Locking Oval Handle (LO)Stainless-Steel Handle (SH)Tee Handle (TH)Locking Handle (LD)Extension Handle (XH)Extension Handle w/Memory Stop (XM)Memory Stop (MS)Chain Lever (CL)
S E C T I O N 1
continued
2-PIECEBRONZE LEAD-FREEBRONZE BALL VALVESFOR POTABLEWATER SERVICE*Standard Port
UPBA-150 / UPBA-150S600 WOG, MSS SP-110, Solder, UPBA-150S with Stainless Steel Ball & Stem 3/8" thru 3"
Full Port
UPBA-100H 600 WOG, MSS SP-110, Threaded With Hose, Cap and Chain1/2" and 3/4"
UPBA-150H 600 WOG, Solder with Hose, Cap and Chain 1/2" and 3/4"
UPBA-400 / UPBA-400S 600 WOG, MSS SP-110, Threaded, UPBA-400S with Stainless Steel Ball & Stem1/4" thru 2"
UPBA-100H P1200 psig @ 250°F, MSS SP-110, Press X Hose 1/2" and 3/4"
UPBA-400 P2 / UPBA-400S P2200 psig @ 250°F, MSS SP-110, Press X Press, UPBA-400S with Stainless Steel Ball and Stem1/2" thru 2"
UPBA-450 / UPBA-450S 600 WOG, MSS SP-110, Solder, UPBA-450S with Stainless Steel Ball & Stem1/2" thru 2"
2-PIECE FORGEDBRASSStandard Port
BA-200400 WOG 150 SWP, Threaded 1/4" thru 4"
BA-250400 WOG 150 SWP, Solder 3/8" thru 3"
Full Port
BA-475B 600 WOG (1/4" thru 3"), 400 WOG (4"), CSA/UL/FM/CGA Approved to 2", Threaded 1/4" thru 4"
BA-485B 600 WOG (1/2"thru 3"), 400 WOG (4"), Heavy Pattern, Solder 1/2" thru 4"
BA-480B / BA-480S 200 psig @ 250°F, Press X Press, BA-480S with Stainless Steel Ball & Stem1/2" thru 3"
BA-490B / BA-490S 200 psig @ 250°F, Press X Threaded, BA-490S with Stainless Steel Ball & Stem1/2" thru 2"
BA-480BH / BA-480SH200 psig @ 250°F, Press X Hose, BA-480SH with Stainless Steel Ball & Stem, 1/2" thru 3/4"
BA-481B200 psig @ 250°F, Press X Press, Extension Stem with Memory stop, 1/2" thru 3"
BA-491B 200 psig @ 250°F, Press X Threaded, Extension stem with Memory Stop, 1/2" thru 2"
* Meets Senate law S3874. IAPMO tested and certified to NSF/ANSI 372 for “lead-free” compliance.
UPBA-100H
UPBA-400 P2 TIH
UPBA-450S
BA-200
BA-475B
BA-480S
S E C T I O N 1
Options/AccessoriesBA-100/150 / UPBA-100/150 BA-400/450 / UPBA-400/450INSULATOR Handle (TIH)Oval Handle (OH)Locking Oval Handle (LO)Stainless-Steel Handle (SH)Tee Handle (TH)Locking Handle (LD)Extension Handle (XH)Extension Handle w/Memory Stop (XM)Memory Stop (MS)Chain Lever (CL)
Options/AccessoriesBA-200/250, BA-475B/485B / UPBA-475B/485BBA-480B/490B / UPBA-480B/490BINSULATOR Handle (TIH) (Except BA-200/250)Oval Handle (OH)Stainless-Steel Handle (SH)Tee Handle (TH) Extension Handle (XH)Extension Handle with Memory Stop (XM)Memory Stop (MS)
2-PIECELEAD-FREE FORGEDBRASS BALL VALVESFOR POTABLE WATERSERVICEFull Port
UPBA-475B * 600 WOG (1/4" thru 2") 400 WOG (2-1/2" thru 3") MSS SP-110, UL/CSA Rated to 2", Threaded1/4" thru 3"
UPBA-485B * 600 WOG (1/2" thru 2") 400 WOG (2-1/2" thru 3"), MSS SP-110, Solder1/2" thru 3"
UPBA-480B / UPBA-480S*200 psig @ 250°F, MSS SP-110, Press X Press, UPBA-480S with Stainless Steel Ball and Stem1/2" thru 4"
UPBA-480BH / UPBA-480SH *200 PSIG @ 250°F, Press X Hose, BA-480SH with Stainless Steel Ball & Stem, 1/2" and 3/4"
UPBA-481B / UPBA-481S *200 psig @ 250°F, MSS SP-110, Press X Press, Extension Stem With Memory Stop, UPBA-481S with Stainless Steel Ball and Stem1/2" thru 2"
UPBA-490B / UPBA-490S *200 psig @ 250°F, MSS SP-110, Press X Threaded, UPBA-490S with Stainless Steel Ball and Stem1/2" thru 2"
UPBA-491B / UPBA-491S *200 psig @ 250°F, MSS SP-110, Press X Threaded, Extension Stem With Memory Stop, UPBA-491S with Stainless Steel Ball and Stem1/2" thru 2"
2-PIECE BRASSCIRCULATOR-FLANGEBA-500 600 WOG, 150 SWP, Full Port, Sold in Pkg. of 2, Threaded3/4" thru 1-1/4"
BA-550 600 WOG, 150 SWP, Full Port, Sold in Pkg. of 2, Solder3/4" thru 1-1/4"
3-PIECE BRONZEBALL VALVESFull Port
BA-300 / BA-300S600 WOG, 150 SWP, MSS SP-110, Threaded, BA-300S with Stainless Steel Ball & Stem1/4" thru 3" *
BA-300SB / BA-300SBS600 WOG, 150 SWP Silbrazed, BA-300SBS with Stainless Steel Ball & Stem3/4" thru 2"
BA-350 / BA-350S600 WOG, 150 SWP, MSS SP-110, Solder, BA-350S with Stainless Steel Ball and Stem3/8" thru 3"
BA-300 P2 / BA-300S P2200 psig @ 250°F, MSS SP-110, Press X Press, BA-300S P2 with Stainless Steel Ball and Stem1/2" thru 2"
BA-350TE / BA-350STE **600 WOG, 150 SWP, Solder, BA-350STE with Stainless Steel Ball and Stem, Tube End1/2" thru 3"
* Meets Senate law S3874. Tested and certified by IAPMO R & T to NSF/ANSI 61 and NSF/ANSI 372 for “lead-free” compliance.** Available in various configurations such as gauge ports and oxygen cleaning for medical gas services
UPBA-475B
UPBA-480
UPBA-481B
BA-300TIH
BA-350TE
BA-500
B A L L VA LV E S
Options/AccessoriesBA-475B/485B / UPBA-475B/485BBA-480B/490B / UPBA-480B/490BINSULATOR Handle (TIH) (BA-480B/BA-490B only)Oval Handle (OH)Stainless-Steel Handle (SH)Tee Handle (TH) Extension Handle (XH)Extension Handle with Memory Stop (XM)Memory Stop (MS)
Options/AccessoriesBA-300/350 / UPBA-300/350INSULATOR Handle (TIH)Oval Handle (OH)Locking Oval Handle (LO)Stainless-Steel Handle (SH)Tee Handle (TH)Locking Handle (LD)Extension Handle (XH)Extension Handle w/Memory Stop (XM)Memory Stop (MS)Chain Lever (CL)
S E C T I O N 1
* Meets Senate law S3874. IAPMO tested and certified to NSF/ANSI 372 for “lead-free” compliance. TEFLON is a registered trademark of DuPont.
3-PIECELEAD-FREE BRONZEBALL VALVES FORPOTABLE WATERFull Port
UPBA-300 / UPBA-300S600 WOG, MSS SP-110, Threaded, UPBA-300S with Stainless Steel Ball & Stem1/4" thru 3"
UPBA-350 / UPBA-350S600 WOG, MSS SP-110, Solder, UPBA-350S with Stainless Steel Ball & Stem 3/8" thru 3"
UPBA-300 P2 / UPBA-300S P2200 psig @ 250°F, MSS SP-110, Press X Press, UPBA-300S P2 with Stainless Steel Ball & Stem1/2" thru 2"
UNIBODY, FLANGED-ENDStandard Port
F90CS150R-N1 Class 150, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Actuator Mounting Pads1/2" thru 6"
F90CS300R-N1 Class 300, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Actuator Mounting Pads1/2" thru 6"
F90SS150R-N1Class 150, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Actuator Mounting Pads1/2" thru 6"
F90SS300R-N1Class 300, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Actuator Mounting Pads1/2" thru 6"
UNIBODY, FLANGED-END, FIRE-SAFEStandard Port
F91CS150R-N1Class 150, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Fire-Safe to API 607, Actuator Mounting Pads 1/2" thru 6"
F91CS300R-N1Class 300, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Fire-Safe to API 607, Actuator Mounting Pads 1/2" thru 6"
UPBA-350F90SS300R-N1
F90CS150R-N1
F91CS150R-N1
S E C T I O N 1
Options/AccessoriesBA-300/350 / UPBA-300/350INSULATOR Handle (TIH)Oval Handle (OH)Locking Oval Handle (LO)Stainless-Steel Handle (SH)Tee Handle (TH)Locking Handle (LD)Extension Handle (XH)Extension Handle w/Memory Stop (XM)Memory Stop (MS)Chain Lever (CL)
Options/AccessoriesF90/91Stainless Oval Handle (OS) Carbon Oval Handle (OH)Extended Handle (XH)Extended Locking Handle (XLH) Gear Operator (GO) Pneumatic ActuatorElectric ActuatorAssemble Dry (AD)Chlorine Cleaned (CC)Oxygen Cleaned OC) Grounded Ball (GB) Vented Ball (VB)
TEFLON is a registered trademark of DuPont
continued
UNIBODY, FLANGED-END, FIRE-SAFEStandard Port
F91SS150R-N1Class 150, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Fire-Safe to API 607, Actuator Mounting Pads 1/2" thru 6"
F91SS300R-N1Class 300, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Fire-Safe to API 607, Actuator Mounting Pads 1/2" thru 6"
UNIBODY, THREADED, FIRE-SAFEReduced Port
10CSOD-02-LL2000 WOG, Carbon Steel Body, Stainless Steel Ball & Stem, RPTFE Seats, Fire-Safe to API 607, Threaded1/4" thru 2"
10SSOD-02-LL2000 WOG, Stainless Steel Body, Stainless Steel Ball & Stem, RPTFE Seats, Fire-Safe to API 607, Threaded 1/4" thru 2"
2-PIECE, FLANGED-END, FIRE-SAFEF201CSN2Class 150, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Full Port, Live Loaded Graphite Packing, Actuator Mounting Pads, Fire-Safe to API 607 1" thru 12"
F203CSN2Class 300, TEFLON ® NXT-75 Seats, Carbon Steel Body, Stainless Steel Ball & Stem, Full Port, Live Loaded Graphite Packing, Actuator Mounting Pads, Fire-Safe to API 607 1" thru 12"
F201SSN2Class 150, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Full Port, Live Loaded Graphite Packing, Actuator Mounting Pads, Fire-Safe to API 6071" thru 12"
F203SSN2Class 300, TEFLON ® NXT-75 Seats, Stainless Steel Body, Stainless Steel Ball & Stem, Full Port, Live Loaded Graphite Packing, Actuator Mounting Pads, Fire-Safe to API 6071" thru 12"
DIVERTER VALVEStandard Port
BA3WDSLH 1000 WOG, Stainless Steel Body, Stainless Steel Ball & Stem, RPTFE Seats, 3-Way Port Diverter, Threaded Ends1/4" thru 2"
F91SS150R-N1
F201CSN2
F201SSN2
10SSOD-02-LL
B A L L VA LV E S
BA3WDSLH
Options/AccessoriesF91Stainless Oval Handle (OS) Carbon Oval Handle (OH)Extended Handle (XH)Extended Locking Handle (XLH) Gear Operator (GO) Pneumatic ActuatorElectric ActuatorAssemble Dry (AD)Chlorine Cleaned (CC)Oxygen Cleaned OC) Grounded Ball (GB) Vented Ball (VB)
Options/AccessoriesF20Lever Handle (2)Gear Operator (3)Pneumatic ActuatorElectric ActuatorAssemble Dry (A) Chlorine Cleaned (C) Oxygen Cleaned (O) Vented Ball (V) Flat-Faced Flange (F) PTFE Packing (T)
S E C T I O N 1
TEFLON is a registered trademark of DuPont
2-PIECE, THREADEDStandard Port
20BSOR-02600 WOG, Bronze Body, Stainless Steel Ball & Stem, RPTFE Seats, Actuator Mounting Pads, Threaded1/4" thru 2"
20BBOR-02600 WOG, Bronze Body, Chrome Plated Ball, Bronze Stem, RPTFE Seats, Actuator Mounting Pads, Threaded1/4" thru 2"
20CSOR-N1Carbon Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Actuator Mounting Pads, Threaded2000 WOG 1/4" thru 1", 1500 WOG 1-1/4" thru 2"
20SSOR-N1Stainless Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Actuator Mounting Pads, Threaded2000 WOG 1/4" thru 1"1500 WOG 1-1/4" thru 2"
Full Port
BA-2601000 WOG, Stainless Steel Body and Ball, RPTFE Seats, Locking Handle, Threaded1/4" thru 3"
HIGH-PRESSURE, SEAL-WELDED, FIRE-SAFEFull Port
41CSOF-02-LLCarbon Steel Body, Stainless Steel Ball & Stem, Available with Socket-Weld, Extended Butt-Weld Ends and 3,000-lb. Configuration (Consult Factory), Actuator Mounting Pads, ThreadedClass 900 1/2" thru 1-1/2"Class 600 2"
41SSOF-02-LLStainless Steel Body, Stainless Steel Ball & Stem, Available with Socket-Weld, Extended Butt-Weld Ends and 3,000-lb. Configuration (Consult Factory), Actuator Mounting Pads, ThreadedClass 900 1/2" thru 1-1/2"Class 600 2"
2-PIECE,SEAL-WELDEDStandard Port
22CSOR-N1Carbon Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Actuator Mounting Pads, Threaded 2000 WOG 1/4" thru 1"1500 WOG 1-1/4" thru 2"
22SSOR-N1Stainless Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Actuator Mounting Pads, Threaded 2000 WOG 1/4" thru 1"1500 WOG 1-1/4" thru 2"
20SS0R-N1
BA-260
22SSOR-N1
41CSOF-02-LL
41SSOF-02-LL
S E C T I O N 1
20BSOR-02
Options/Accessories20 seriesStainless Oval Handle (OS) Stainless Latch Lock Handle (LL) Stainless-Steel Spring-Loaded Oval Handle (LO) Extended Handle (XH) Stainless Spring Latch-Lock Handle (LS) Pneumatic ActuatorElectric ActuatorAssemble Dry (AD) Grounded Ball (GB) Grounded Stem (GS) Vented Ball (VB)
Options/Accessories22 seriesStainless Oval Handle (OS) Stainless Latch Lock Handle (LL) Stainless-Steel Spring-Loaded Oval Handle (LO) Extended Handle (XH) Stainless Spring Latch-Lock Handle (LS) Pneumatic ActuatorElectric ActuatorAssemble Dry (AD) Grounded Ball (GB) Grounded Stem (GS) Vented Ball (VB)
41 SeriesStainless Handle (SH) Stainless Oval Handle (OS) Stainless Latch Lock Handle (LL) Carbon-Steel Oval Handle (OH) Locking Spring-Return Stainless-Steel Oval Handle (LO) Extended Handle (XH) Stainless Spring Latch Lock Handle (LS)
3-PIECE, THREADEDFull Port
30BBOF-02600 WOG, Bronze Body, Chrome Plated Ball & Stem, RPTFE Seats, PTFE V-Ring Packing, Threaded, Available with Solder, Actuator Mounting Pads 1/4" thru 2"
30BSOF-02600 WOG, Bronze Body, Stainless Steel Ball & Stem, RPTFE Seats, PTFE V-Ring Packing, Actuator Mounting Pads, Threaded, Available with Solder1/4" thru 2"
30CSOF-021000 WOG, Carbon Steel Body, Stainless Steel Ball & Stem, RPTFE Seats, PTFE V-Ring Packing, Actuator Mounting Pads, Threaded, Available with Socket-Weld 1/4" thru 2"
30SSOF-021000 WOG, Stainless Steel Body, Stainless Steel Ball & Stem, RPTFE Seats, PTFE V-Ring Packing, Actuator Mounting Pads, Threaded, Available with Socket-Weld1/4" thru 2"
3-PIECE,ENCLOSED-BOLT,FIRE-SAFEStandard Port
35RCS0N-LL2000 WOG, Carbon Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Fire-Safe to API 607, Live Loaded Graphite Packing, Actuator Mounting Pads, Threaded, Available with Socket-Weld1/4" thru 2"
35RSSON-LL2000 WOG, Stainless Steel Body, Stainless Steel Ball & Stem, Live Loaded Flexible Graphite Packing, TEFLON® NXT-75 Seats, Fire-Safe to API 607, Actuator Mounting Pads, Threaded, Available with Socket-Weld 1/4" thru 2"
Full Port
35FCSON-LL2000 WOG, Carbon Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Fire-Safe to API 607, Live Loaded Graphite Packing, Actuator Mounting Pads, Threaded, Available with Socket-Weld 1/4" thru 2"
35FSSON-LL2000 WOG, Stainless Steel Body, Stainless Steel Ball & Stem, TEFLON® NXT-75 Seats, Fire-Safe to API 607, Live Loaded Graphite Packing, Actuator Mounting Pads, Threaded, Available with Socket-Weld1/4" thru 2"
30SSOF-02
30BSOF-02
30CSOF-02
35RCS0N-LL
30SSOF-02-LO
35RCS0N-LL
TEFLON is a registered trademark of DuPont
B A L L VA LV E S
Options/Accessories30 SeriesStainless Latch Lock Handle (LL)Locking Stainless-Steel Oval Handle (LO)Stainless-Steel Latch Lock Spring- Loaded Handle (LS) Stainless-Steel Oval Handle (OS) Extended Handle 2" (XH) Extended Handle 4 1/2" (XLH) Extended Handle (XH)Pneumatic ActuatorElectric ActuatorAssemble Dry (AD) Grounded Ball (GB) Grounded Stem (GS) Vented Ball (VB)
Options/Accessories35 seriesLatch Lock Handle (LL) Locking Stainless-Steel Oval (LO) Extended Handle (XH) Pneumatic ActuatorElectric ActuatorAssemble Dry (A) Chlorine Cleaned (Stainless Only) (C) Oxygen Cleaned (O)
S E C T I O N 1
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
UNIBODY, SCREWED END,DOUBLE REDUCED PORTBALL VALVEAPI-607 FIRESAFE 4th Ed.
2000 WOG10 SERIES 1
4 -"/ 2 "FED. SPEC. WW-V-35C, II, Style 3
MSS SP-110
MATERIALS LIST
GNIKROW
ERUSSERP-p
is
WORKING TEMPERATURE - F
200
800
400600
10001200
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPk
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
1400160018002000
SaturatedSteam
1380
5520
27604140
690082809660110401242013800
232
DIMENSIONS
D
H
A
CB
1098
7
6
5
4
3 2
1
ITEM PART MODEL MATERIALS MAT. SPEC.10CSOD-02-LL Carbon Steel A 216-WCB10SSOD-02-LL Stainless Steel A 351-CF8M10CSOD-02-LL Carbon Steel A 216-WCB10SSOD-02-LL Stainless Steel A 351-CF8M10CSOD-02-LL Stainless Steel 316 SS10SSOD-02-LL Stainless Steel 316 SS10CSOD-02-LL10SSOD-02-LL10CSOD-02-LL10SSOD-02-LL10CSOD-02-LL10SSOD-02-LL10CSOD-02-LL10SSOD-02-LL10CSOD-02-LL Carbon Steel A 283 CS10SSOD-02-LL Stainless Steel 316 SS10CSOD-02-LL Carbon Steel A 283 CS10SSOD-02-LL Stainless Steel 304 SS10CSOD-02-LL Carbon Steel A 283 CS10SSOD-02-LL Stainless Steel 304 SS
10SERM TLS.xls
_GRAPHOIL
Stainless Steel 316 SS
_
_RTFE
RTFE
8
9
10HandleNut
Handle
Gland
6ThrustWasher
7StemPacking
1 Body
5 Seat
3 Ball
4 Stem
2BallRetainer
150 1035
Pressure RatingTemperature Range -20Body
Sizes 1/4”-2”2000 WOG / 150 WSP
to 450 F.Material WCB or CF8M.
Body materials meet specifications.RPTFE Seats Standard.One Piece Investment Cast BodyValves are and includegraphite stem-packing.
All valves are tested in accordance with latest.
Blow-out Proof StemLow Torque SeatsStandard Locking Handle
ASTM
API 607 Fire-Safe
ASME B16.34 specifications
1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"DN6 DN10 DN15 DN20 DN25 DN32 DN40 DN50
INCHES 2.28 2.28 2.60 2.83 3.23 3.54 3.86 4.33mm 57.9 57.9 66.0 71.9 82.0 89.9 98.0 110.0
INCHES 1.10 1.10 1.10 1.34 1.61 1.97 2.24 2.76mm 27.9 27.9 27.9 34.0 40.9 50.0 56.9 70.1
INCHES 0.31 0.31 0.31 0.48 0.63 0.81 1.00 1.25mm 7.9 7.9 7.9 12.2 16.0 20.6 25.4 31.8
INCHES 4.17 4.17 4.17 4.17 5.71 5.71 7.24 7.24mm 105.9 105.9 105.9 105.9 145.0 145.0 183.9 183.9
INCHES 1.97 1.97 1.97 2.20 2.56 2.76 3.29 3.49mm 50.0 50.0 50.0 55.9 65.0 70.1 83.6 88.6
F THREADSIZE 1/4" NPT 3/8" NPT 1/2" NPT 3/4" NPT 1" NPT 1-1/4" NPT 1-1/2" NPT 2" NPT
Cv 3 4 5 9 14 22 50 8110SERDIM .xls
UNITS
Note: DN (Diameter Nominal) = Metric equivalent size.
H
A
B
C
D
Rev. 3
Rev. 4
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
20/22 Series Ball Valve Milwaukee Valve Company 20CC/CS/SS and 22CC/CS/SS
2 Piece Standard Port NPT Ball Valve
Features and Benefits • Locking lever for safety lockout• Multiple V-ring stem packing arrangement for longer packing life• Vent hole in ball slot for cavity venting• Mounting pad for easy actuation• PTFE body seal/except on 22 series• NACE Compliant for sour gas service• Blow-out proof stem• Cantilever seat design for low operating torque• 22 series offers sealed welded body to tailpiece construction• Meets latest ASME, MSS-SP and ASTM specifications
Operators Available • Locking lever handle and ovals• Pneumatic and Electric Actuation
Materials of Construction • WCB Carbon steel or CF8M Stainless Steel• Ball: 316 Stainless• Stem: 316 Stainless• Seats: Teflon®-75 (M-PTFE)• Packing: PTFE/Graphite• Handles: Stainless Steel/Carbon Steel
Specifications Pressure Ratings: • Valves Sizes 1/4” through 2.0”
1/4” through 1” 2000 psi • Meets MSS-SP-110
1-1/4” through 2.0” 1500 PSI • Valves meet NACE MRO175
Valve is rated 150 psi steam @ 365°F• 250 psi steam rating w/ 03 Multifil seats
Torque & CV Values
0 500 750 1000 1000 1500 2000
DelrinKel-F 300 265 247 230 230 195 159 124 89 54 19 0Virgin Teflon 400 333 275 217 217 100 0Glass Fld TFE 450 333 275 217 217 100 0Multifil 500 400 360 325 325 270 200Loperm 475 400 360 325 325 270 200Endurofil 550 550 550 540 540 520 500 419 339 259 179 0
Nylon 200 189.9 183.5 179.2 179.2 168.5 157.9 149.3 138.7 129.1 119.5 0FEP 400 247.5 177.1 100 0
0
500
1000
1500
2000
2500
0 100 200 300 400 500 600
Pres
sure
PSI
G
Temperature Degrees Fahrenheit
1/4" to 1" 2000 #
Milwaukee Valve Company16550 West Stratton DriveNew Berlin, WI 53151Phone 262 432 2800Fax 262 432 2701
Milwaukee Valve 20 Series Top Level Matrix
Revision B
Series Body Material Ball / Stem Material End Connection Type Port Size Seat Material External Options Internal Options SizeXXXXXXXXXXXXXXXX
20 - Two piece Adaptor Loaded C - Carbon Steel (WCB) S - Stainless Steel (316) 0 - FNPT R - Reduced N1 - NXT Standard seat LL - Stainless Latch-Lock Handle AD- Assemble Dry - 014 - 1/4" - 10)M8FC( leetS sselniatS - SdedleW-laeS eceip owT -22 Virgin PTFE LS- SS Spring Loaded Latch Lock GB- Grounded Ball 038 - 3/8"
02 - Reinforced PTFE (15% Gls.) LO- SS Locking Spring Loaded Oval GS- Grounded Stem 012 - 1/2"03 - Multi-Fill PTFE (steam seat OS - Stainless Oval Handle VB - Vented Ball 034 - 3/4"
"1 - 001)"2( eldnaH dednetxE - HX) isp 052 114 - 1-1/4"112 - 1-1/2"200 - 2"
How To Order Milwaukee Valve 20 Series Two Piece Ball Valve
20CSOR-N1-LL 34 (3/4" Two Piece Adaptor Loaded Reduced Port Carbon Steel Body, Stainless Trim, Female NPT End Pieces, NXT. Seats, SS Latch-Lock Handle,)20CSOR-N1-LL-VB 34 (3/4" Two Piece Adaptor Loaded Reduced Port Carbon Steel Body, Stainless Trim, Female NPT End Pieces, NXT. Seats, SS Latch-Lock Handle, Vented Ball)
Example Product Numbers
Milwaukee Valve ConfidentialMTV 20 SERIES PRODUCT MATRIX.xls 7/26/06 Page 1
C - Carbon Steel
VALVE SIZE
MAXIMUM BREAKAWAY
TORQUE (in lbs.)Cv
1/4 - 3/8 20 6.81/2 40 9.83/4 50 25
1 100 351 - 1/4 140 471 - 1/2 190 81
2 240 105
20/22 Series Ball Valve Milwaukee Valve Company 20CC/CS/SS and 22CC/CS/SS
2 Piece Standard Port NPT Ball Valve
Features and Benefits • Locking lever for safety lockout• Multiple V-ring stem packing arrangement for longer packing life• Vent hole in ball slot for cavity venting• Mounting pad for easy actuation• PTFE body seal/except on 22 series• NACE Compliant for sour gas service• Blow-out proof stem• Cantilever seat design for low operating torque• 22 series offers sealed welded body to tailpiece construction• Meets latest ASME, MSS-SP and ASTM specifications
Operators Available • Locking lever handle and ovals• Pneumatic and Electric Actuation
Materials of Construction • WCB Carbon steel or CF8M Stainless Steel• Ball: 316 Stainless• Stem: 316 Stainless• Seats: Teflon®-75 (M-PTFE)• Packing: PTFE/Graphite• Handles: Stainless Steel/Carbon Steel
Specifications Pressure Ratings: • Valves Sizes 1/4” through 2.0”
1/4” through 1” 2000 psi • Meets MSS-SP-110
1-1/4” through 2.0” 1500 PSI • Valves meet NACE MRO175
Valve is rated 150 psi steam @ 365°F• 250 psi steam rating w/ 03 Multifil seats
Torque & CV Values
PSI20001500
Pressure Ratings:1/4" through 1"1-1/4" through 2"Valve is rated 150 psi steam @ 365°F
Tefl on is a registered trademark of Dupont.
Rev 3
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
20CC/CS/SS and 22CC/CS/SSNPT Ball Valve
Material List
Material ListItem Description 20/22/SS 20/22/CC 20/22/CS
1 BodyASTM A351/A744
CF8MCarbon Steel
ASTM A216 WCBCarbon Steel
ASTM A216 WCB
2 TailpieceASTM A351/A744
CF8MCarbon Steel
ASTM A216 WCBCarbon Steel
ASTM A216 WCB
3 StemStainless Steel
ASTM A276 Type 316
Stainless SteelASTM A276 Type
316
Stainless SteelASTM A276 Type
316
4 BallStainless Steel
ASTM A276 Type 316
Carbon SteelAISI-12L14 Hard Chrome Plated
Stainless SteelASTM A276 Type
316
5 Handle NutStainless Steel
18-8Stainless Steel
18-8Stainless Steel
18-8
6 Handle AssemblyStainless Steel
Type 304Carbon SteelZinc Plated
Stainless SteelType 304
7 Lock WasherStainless Steel
Type 304Stainless Steel
Type 304Stainless Steel
Type 304
8 Packing NutStainless Steel
ASTM 276 Type 316
Carbon SteelAISI-12L14
Carbon SteelAISI-12L14
9 Seat NXT75 NXT75 NXT7510 Thrust Washer NXT75 NXT75 NXT7511 Packing PTFE PTFE PTFE12 Body Seal* PTFE PTFE PTFE
IN0.3752.0901.6500.8204.1870.5001.120
0.1960.3900.875
ABCDEFGHJKL
SIZE
DIMENSIONS - INCHES AND MILLIMETERS (20/22 - SERIES BALL VAVLES)
IN0.3752.0901.6500.8204.1870.5001.120
0.1960.3900.875
IN0.5002.3601.7701.0604.1870.5001.120
0.1960.3901.000
MM9.5353.0941.9120.83106.3512.728.45
4.989.9122.23
MM9.53053.09041.91020.830106.35012.70028.450
4.9809.91022.230
MM12.7059.9444.9626.92106.3512.7028.45
4.989.91
24.40
MM17.4571.1252.0734.04
146.0522.0134.80
6.9914.2231.75
MM22.2382.0456.9041.15
146.0522.0134.80
6.9914.2231.75
MM25.4091.9562.9947.75
193.6823.6238.10
9.0216.5134.93
MM31.75
103.1268.0757.15
193.6823.6238.10
9.0216.5134.93
MM38.10
118.1173.9169.85
193.6823.6238.10
9.0216.5134.93
IN0.6872.8002.0501.3405.7500.8701.370
0.2750.5601.250
IN0.8753.2502.2401.6205.7500.8701.370
0.2750.5601.250
IN1.0003.6202.4801.8807.6250.9301.500
0.3550.6501.375
IN1.2504.0602.6802.2507.6250.9301.500
0.3550.6501.375
IN1.5004.6502.9102.7507.6250.9301.500
0.3550.6501.375
10-24NC 10-24NC 10-24NC 10-24NC 10-24NC 1/4-20NC 1/4-20NC 1/4-20NC
1/4” 3/8” 1/2” 3/4” 1” 1-1/4” 1-1/2” 2”
Rev 3
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
Tefl on is a registered trademark of Dupont.
30 Series Ball ValveMilwaukee Valve Company30CC/CS/SS
3 Piece Full Port Ball Valve
Features and Benefits • Locking lever for safety lockout • Multiple V-ring stem packing arrangement
for longer packing life • Vent hold in ball slot for cavity venting • Mounting pad for easy actuation • TFE/Graphite Body Seal • NACE Compliant for sour gas service • Blow-out proof stem • Cantilever seat design for low operating torque • Meets ASME, MSS-SP and ASTM specifictions
Operators Available • Locking lever handle and ovals • Pneumatic and Electric Actuation
Materials of Construction • Body: WCB Carbon steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Stainless • Seats: PTFE, RPTFE, Multi-Fil • Packing: PTFE/Graphite • Handles: Stainless Steel/Carbon Steel
Specifications and Product Range • Valve Sizes 1/4” through 2” • Meets MSS-SP-110 • Valves meet NACE MRO175 • Socket Weld and NPT Connections
Pressure Ratings: PSI1/4” throught 2” 1000
Valve is rated 150 psi steam @ 365°F with RPTFE seats
Series: Body: Ball/Stem Material: End Connection Type: Port Size: Seat Material: External Options: Internal Options: Size30-Three Piece 1000 WOG C = Carbon Steel (WCB) S = Stainless Steel (316) 0 = NPT Female F = Full Port 01 = Virgin PTFE LL = Stainless Latch-Lock Handle AD = Assembly Dry 014 - 1/4"
S= Stainless Steel (CF8M) C= Carbons Steel Plated 1 = Socket-Weld 02 = Reinforced PTFE (15% Gls.) LS = Stainless Latch-Lock Handle-Spring-Loaded GB = Grounded Ball 038-3/8"6 = FNPT/Socket-Weld 03 = Multi-Fill PTFE (steam seat 250 psi) LO = Locking Stainless Oval Handle-Spring-Loaded GS = Grounded Stem 012 - 1/2"
OS = Stainless Oval Handle VB = Vented Ball 034-3/4"XH = Extended Handle (2" ) 100-1"XLH = Extended Handle (4 1/2" ) 114-11/4"
112-11/2"200-2"
30CSOF-02-LL - 34 (3/4" Three Piece Full Port Carbon Steel Body, Stainless Trim, Female NPT End Pieces, RPTFE Seats, SS Latch-Lock Handle)30CSOF-02-LL-VB - 34 (3/4" Three Piece Full Port Carbon Steel Body, Stainless Trim, Female NPT End Pieces, RPTFE Seats, SS Latch-Lock Handle,Vented Ball)
HowtoOrderMilwaukeeValve30SeriesThreePieceBallvalve
Example Product Numbers
VALVESIZE
MAXIMUMBREAKAWAY
TORQUE (in lbs)Cv(GPM)
1/4-3/8 30 91/2 50 103/4 70 311 125 49
1-1/4 210 851-1/2 360 110
2 600 360
Rev 0918
Torque & Cv Values
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
30CC/CS/SS3-Piece Full Port Ball Valve
DESCRIPTION
1. Body
2. Endcap
3. Stem
4. Ball
5. Handle Nut
6. Handle Assembly
7. Lock Washer
8. Packing Nut
9. Body Capscrews
10. Body Nuts
11. Seats (02)
12. Thrust Washer
13. Packing
14. Body Seal
30CCOF-02Carbon Steel
ASTM A216, WCBCarbon Steel
ASTM A216, WCBCarbon SteelAISI - 12L14Carbon Steel AISI -12L14
Low Carbon Steel Zinc-Plated
AISI 1010 Steel Zinc-Plated
Carbon Steel Plated
Carbon SteelAISI - 12L14
SAE J429 Gr.8 Zinc-Plated
SAE J429 Gr.8 Zinc-Plated
15% Glass-Filled,Reinforced PTFE
PTFE
PTFE
PTFE (01)Graphoil (03)
30CSOF-02Carbon Steel
ASTM A216, WCBCarbon Steel
ASTM A216, WCBStainless Steel
ASTM A276, Type 316Stainless Steel
ASTM A276, Type 316Stainless Steel
18-8Stainless Steel
18-8Stainless Steel
Type 304Carbon SteelAISI - 12L14
SAE J429 Gr.8 Zinc-Plated
SAE J429 Gr.8 Zinc-Plated
15% Glass-Filled,Reinforced PTFE
PTFE
PTFE
PTFE (01)Graphoil (03)
30SSOF-02Stainless Steel
ASTM A351/744, CF8MStainless Steel
ASTM A351/744, CF3MStainless Steel
ASTM A276, Type 316Stainless Steel
ASTM A276, Type 316Stainless Steel
18-8Stainless Steel
18-8Stainless Steel
Type 304Stainless Steel
ASTM A276, Type 316ASTM F593
Gr. CASTM F593
Gr. C15% Glass-FilledReinforced PTFE
PTFE
PTFE
PTFE (01)Graphoil (03)
DIMENSIONS
* These dimensions apply only to socket-weld end valves.
L
N = NUMBER OF ACTUATOR MOUNTING PADS HOLES
M
MATERIAL LIST
Rev 0918
35 Series Ball Valve Milwaukee Valve Company 35RSS/35RCS AND 35FSS/35FCS 3 Piece Enclosed Bolt Fire-Safe Full & Standard Port Ball Valve Features and Benefits
• Locking lever for safety lockout • Live-loaded adjustable stem packing arrangement
for longer packing life • Vent hole in ball slot for cavity venting • Standard grounded ball and stem • ISO 5211 mounting pad for easy actuation • Flexible graphite body seals • NACE Compliant for sour gas service • Blow-out proof stem • Fire-safe to API 607 6th Ed • Cantilever seat design for low operating torques • Meets the latest: API, ASTM/ASME standards
Product Range • Full and Standard port available • Socket weld and NPT connections • Size Range 1/4”-2.0”
Operators Available • Locking lever and oval handle • Pneumatic and Electric Actuation
Materials of Construction • Carbon Steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Stainless • Seats: NXT 75/M-PTFE • Seat options: Multi-Fill, PEEK • Packing: Graphite/PTFE
Specifications
• Valves Sizes 1/4” through 2” • Meets MSS-SP-110 • Meets ASME B16.34 design • Valves meet API 608 • Valves meet API 607 6th Ed for Fire safe testing • Valves tested to API 598 and MSS SP-72 • Valves meet NACE MRO175
Milwaukee Valve Company16550 West Stratton DriveNew Berlin, WI 53151Phone 262 432 2800Fax 262 432 2701
Milwaukee Valve 35 Series Top Level Matrix
Revision B
Series Port Size Body Material Ball / Stem Material End Piece Configuration Seat Material External Options Internal Options SizeXXXXXXXXXXXXXXX
yrD elbmessA - AeldnaH kcoL-hctaL sselniatS - LLdtS TXN - NTPNF - 0)613( leetS sselniatS - S)BCW( leetS nobraC - CdradnatS-R53 - 014 - 1/4""8/3 - 830llaB detneV - VeldnaH lavO sselniatS - OLEFTP nigriV - 1dleW tekcoS - 1)M8FC( leetS sselniatS - SlluF - F"2/1 - 210* naelC negyxO - O)"4( eldnaH dednetxE - HX).slG %51( EFTP decrofnieR - 2** dleW ttuB dednetxE - 2 "4/3 - 430naelC enirolhC - CEFTP lliF-itluM - 3** dleW tekcoS dednetxE - 3
"1 - 001ylno sselniatS *** keeP - 6TPNF / dleW tekcoS - 67 - Extended Socket Weld / FNPT** ** Contact Factory 114 - 1-1/4"** Contact Factory 112 - 1-1/2"
200 - 2"
How To Order Milwaukee Valve 35 Series Three Piece Enclosed Bolt Ball Valve
35RCS02LL -034 (3/4" Standard Port Carbon Steel Body, Stainless Trim, Female NPT End Pieces, Gls. Fld Seats, SS Latch-Lock Handle,)35FSS13LL -100 (1" Full Port Stainless Steel Body, Stainless Trim, Socket Weld End Pieces, Multi-Fill PTFE Seats, SS Latch-Lock Handle,)35RSS02LLV -034 (3/4" Standard Port Stainless Steel Body, Stainless Trim, Female NPT End Pieces, Gls. Fld Seats, SS Latch-Lock Handle, Vented Ball)
Example Product Numbers
Milwaukee Valve ConfidentialMTV 35 3pc Enclosed Bolt Ball Valve Top Level Matrix rev 2 cat info.xlsx 7/26/06 Page 1
Pressure Ratings: Class 800Carbon Steel 2000 psiStainless Steel 2000 psiValve is rated 150 steam @ 365 degrees F.
0 500 750 1000 1000 1500 2000
DelrinKel-F 300 265 247 230 230 195 159 124 89 54 19 0EndurofilGlass Fld TFE 450 333 275 217 217 100 0Multifil 500 400 360 325 325 270 200Loperm 475 400 360 325 325 270 200Endurofil 550 550 550 540 540 520 500 419 339 259 179 0
Nylon 200 189.9 183.5 179.2 179.2 168.5 157.9 149.3 138.7 129.1 119.5 0FEP 400 247.5 177.1 100 0
0
500
1000
1500
2000
2500
0 100 200 300 400 500 600
Pres
sure
PSI
G
Temperature Degrees Fahrenheit
1/4 -2" Body Rating
35 Series Ball Valve Milwaukee Valve Company 35RSS/35RCS AND 35FSS/35FCS 3 Piece Enclosed Bolt Fire-Safe Full & Standard Port Ball Valve Features and Benefits
• Locking lever for safety lockout • Live-loaded adjustable stem packing arrangement
for longer packing life • Vent hole in ball slot for cavity venting • Standard grounded ball and stem • ISO 5211 mounting pad for easy actuation • Flexible graphite body seals • NACE Compliant for sour gas service • Blow-out proof stem • Fire-safe to API 607 6th Ed • Cantilever seat design for low operating torques • Meets the latest: API, ASTM/ASME standards
Product Range • Full and Standard port available • Socket weld and NPT connections • Size Range 1/4”-2.0”
Operators Available • Locking lever and oval handle • Pneumatic and Electric Actuation
Materials of Construction • Carbon Steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Stainless • Seats: NXT 75/M-PTFE • Seat options: Multi-Fill, PEEK • Packing: Graphite/PTFE
Specifications
• Valves Sizes 1/4” through 2” • Meets MSS-SP-110 • Meets ASME B16.34 design • Valves meet API 608 • Valves meet API 607 6th Ed for Fire safe testing • Valves tested to API 598 and MSS SP-72 • Valves meet NACE MRO175
VALVE SIZE
STD PORT
MAXIMUM BREAK AWAY
TORQUE (in.lbs.)
CV
VALVE SIZE FULL PORT
MAXIMUM BREAK AWAY
TORQUE (in.lbs.)
CV
1/4 50 53/8 50 51/2 50 15 1/2 55 153/4 55 25 3/4 135 50
1 135 40 1 200 601 1/4 200 50 1 1/4 350 1101 1/2 340 75 1 1/2 400 1302 420 120 2 550 360
TORQUES AND CV RATINGS
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
Rev 0918
35RSS/35RCS 1/4” to 2” and 35FSS/35FCS 1/2” to 1-1/2”
ITEM DESCRIPTION MATERIAL
1 BODY MACHINED CS ASTM A216 GR WCBSS ASTM A351 GR CF8M
3 END CAP MACHINED CS ASTM A216 GR WCBSS ASTM A351 GR CF8M
5 BALL SS ASTM A351 CF8M6 STEM ASTM A479 TYPE 3167 SEAT NXT 75/M-PTFE8 THRUST WASHER NXT 75/M-PTFE9 FOLLOWER ASTM A479 TYPR 316
10 STEM PACKING GRAPHITE11 BODY SEAL FLEXIBLE GRAPHITE12 STEM NUT ASTM A194 GR8 TYPE 30413 DISC SPRING ASTM A276 TYPE 30414 HANDLE ASSY 304 SS
15 COLLAR, NUT RETAINING ASTM A276 TYPE 304
16 LOCK WASHER ASTM A276 TYPE 30417 BOLT,SHCS ASTM A193-BB TYPE 30418 STOP PIN ASTM A276 TYPE 304
Size Units A B (Port) C D E F G (NPT) G1 (SW) G2 (SW) H J K L
1/2Inches
mm1.35 34.2
.57 14.5
1.98 50.2
1.44 50.2
1.37 34.8
2.74 69.6
1/4"-18NPT.87
22.00.38 9.6
2.62 66.6
2.15 54.7
1.42 36.0
4.21 107.0
3/4Inches
mm1.88 47.7
.81 20.6
2.23 56.7
1.61 41.0
1.59 40.4
3.19 81.0
3/4"-14NPT1.07 27.3
0.5 12.7
3.18 80.7
2.59 65.9
1.65 42.0
5.00 127.0
1 Inches
mm1.88 47.7
.98 24.9
2.58 65.5
1.84 46.8
1.87 47.5
3.74 95.0
1.0"-11 1/2NPT1.34 34.0
0.5 12.7
3.35 85.1
2.96 75.1
1.61 41.0
6.02 152.9
1 1/4 Inches
mm2.25 57.0
1.25 31.8
3.23 82.0
2.07 52.6
2.13 54.1
4.26 108.2
1 1/4"-11 1/2NPT1.69 42.9
0.5 12.7
3.77 95.8
3.41 86.6
1.97 50.0
7.80 198.1
1 1/2Inches
mm2.69 68.2
1.50 38.1
3.51 89.2
2.33 59.1
2.52 64.0
5.04 128.0
1 1/2"-11 1/2NPT1.92 48.9
0.5 12.7
4.00 101.5
4.14 105.1
1.97 50.0
7.80 198.1
Size Units A B (Port) C D E F G (NPT) G1 (SW) G2 (SW) H J K L
1/4Inches
mm1.17 29.6
.43 11.0
1.83 46.4
1.28 32.5
1.36 34.5
2.72 69.0
1/4"-18NPT.57
14.40.38 9.6
2.45 62.1
1.91 48.4
1.42 36.0
4.21 107.0
3/8Inches
mm1.17 29.6
.43 11.0
1.83 46.4
1.28 32.5
1.36 34.5
2.72 69.0
3/8"-18NPT.70
17.80.38 9.6
2.45 62.1
1.91 48.4
1.42 36.0
4.21 107.0
1/2Inches
mm1.35 34.2
.57 14.5
1.98 50.2
1.44 36.5
1.37 34.8
2.74 69.6
1/2"-18NPT.87
22.00.38 9.6
2.59 65.8
2.15 54.7
1.42 36.0
4.21 107.0
3/4Inches
mm1.55 39.5
.57 14.5
1.93 49.0
1.44 36.5
1.45 36.9
2.90 73.7
3/4"-14NPT1.07 27.3
0.5 12.7
2.59 65.8
2.15 54.7
1.42 36.0
4.21 107.0
1Inches
mm1.88 47.7
.81 20.6
2.25 57.0
1.61 41.0
1.59 40.4
3.19 81.0
1.0"-11 1/2NPT1.34 34.0
0.5 12.7
3.14 79.7
2.59 65.9
1.65 42.0
5.00 127.0
1 1/4Inches
mm2.25 57.0
.98 24.9
2.58 65.5
1.84 46.8
1.87 47.5
3.74 95.0
1 1/4"-11 1/2NPT1.69 42.8
0.5 12.7
3.31 84.1
2.96 75.1
1.61 41.0
6.02 152.9
1 1/2Inches
mm2.58 65.5
1.25 31.8
3.23 82.0
2.07 52.6
2.13 54.1
4.26 108.2
1 1/2"-11 1/2NPT1.93 48.9
0.5 12.7
3.71 94.3
3.41 86.6
1.97 50.0
7.80 187.1
2Inches
mm3.18 80.8
1.50 38.1
3.51 89.2
2.33 59.1
2.52 64.0
5.04 128.0
2.0"-11 1/2NPT2.42 61.5
0.6 15.2
3.97 100.8
4.14 105.1
1.97 50.0
7.80 198.1
Full Port
For 2" Full Port dimension see next page
The 1/4, 3/8, 1/2 Valves are full port
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
Rev 0918
35FSS/35FCS 2”
Size Units A B (Port) C D E F G (NPT) G1 (SW) G2 (SW) H K L
2 Inches
mm5.20
132.02.00 50.8
4.34 110.3
3.11 79.0
2.81 71.5
5.63 143.0
2.0"-11 1/2NPT2.42 61.5
0.6 15.2
5.44 138.2
5.20 132.0
11.54 293.0
Full Port
LAIRETAMNOITPIRCSEDMETI
1 BODY MACHINED SS ASTM A351 GR CF8MCS ASTM A216 GR WCB
2 END CAP MACHINED SS ASTM A351 GR CF8MCS ASTM A216 GR WCB
3 BALL STAINLESS STEEL ASTM A351 GR CF8M4 STEM ASTM A479 TYPE 316
NXT 75/M-PTFETAES56 THRUST WASHER NXT 75/M-PTFE7 FOLLOWER ASTM A479 TYPE 3168 STEM PACKING GRAPHITE9 BODY SEAL FLEXIBLE GRAPHITE
10 STEM NUT ASTM A194 GR8 TYPE 30411 DISC SPRING ASTM A479 TYPE 304
SS 403YSSA ELDNAH2113 LOCK TAB ASTM A276 TYPE 30414 LOCK WASHER ASTM A582 TYPE 30315 BOLT,SHCS ASTM A193-B8 TYPE 30416 STOP PIN ASTM A276 TYPE 30417 SEAT SHEATH ASTM A479 TYPE 316
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
Rev 0918
41SS/41CS SERIES BALL VALVESMilwaukee Valve CompanyFull Port Seal-Welded Fire-Safe Ball Valve
Rev 09/18
IN EVERY VALVE
Features and Benefi ts • Locking lever for safety lockout• V-ring stem packing arrangement for longer packing life • Vented ball in ball slot for cavity venting• Four bolt actuator mounting pad for easy actuation• Blow-out proof stem design• Extended ends allow welding in line w/o disassembly • Optional Seat materials offer 3000 psig (Peek/Delrin)• Meets API, ASTM, ASME and MSS standards
Materials of Construction• Body: Carbon Steel or CF8M Stainless Steel • Ball: 316 Stainless• Stem: 316 Stainless• Seats: PTFE, RPTFE, Multi Filled,
Peek, Delrin• Packing: Graphite or PTFE
Operators Available• Locking lever handle, Oval handles, Stem Extension • Pneumatic and Electric Actuation
Example Product Numbers: 41SS0F-02-LL-100 - (1” 41 Series Stainless Steel Body, 316 Stainless Ball and Stem, Full Port, Reinforced PTFE seats, Stainless Latch-Lock Handle)
Torque Ratings and CVValve SizeFull Port
Maximum Breakaway Torque (in lbs.) Cv.
1/4-1/2 60 9.8
3/4 110 35
1 130 47
1-1/4 260 81
1-1/2 330 105
2 550 330
41 Series
Specifi cations• ASME/ANSI Class 900 • Meets ASME B16.34 design• Valves meet API 608 • Valves meet API 607 4th edition for fi re safe testing• Valves tested to API 598 and MSS SP-72• Valve is rated 150 steam @ 365 degrees F with
RPTFE Seats • Valves meet NACE MRO175• End Connections: Threaded/Socket-Weld/Ext.
Butt-Weld Ends • Size Range 1/4”-2”
How To Order Milwaukee Valve 41 Series Seal Welded 2 Piece Ball ValveSeries Body
MaterialBall / Stem Material
End Piece Confi guration
Port Size
Seat Material External Options Internal Options
Size
XX X X X X X XX XX XXX
41 C - Carbon Steel (WCB)S - Stainless Steel (CF8M)
S - Stainless Steel (316)
0 - FNPT1 - Socket Weld6 - Socket/FNPTB - Extended Butt Welded Sch 40 -4” Tube Extension
F - Full 01 - Virgin PTFE02 - Reinforced PTFE (15% Gls.)03 - Multi-Fill PTFE04 - UHMWPE05 - PEEK07 - Delrin
LL - Stainless Latch-Lock HandleOH - Carbon Steel Oval HandleOS - Stainless Oval HandleLO - Locking SS Oval HandleXH - Extended Handle (2.5”)
AD - Assembly DryGB - Grounded BallVB - Vented Ball (Uni-Directional)
014 - 1/4”038 - 3/8”012 - 1/2”034 - 3/4”100 - 1”114 - 1-1/4”112 - 1-1/2”200 - 2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
41SS/41CS SERIES BALL VALVESMaterial List
Part 41SS 41CS
1. BodyStainless SteelASTM A351/A744 CF3M
Carbon SteelASTM-A216 GR, WCB
2. TailpieceStainless SteelASTM A351/A744CF3M
Carbon SteelASTM-A216 GR, WCB
3. Ball Seal Reinforced PTFE 15% Glass Filled
Reinforced PTFE 15% Glass Filled
4. Body/ Tailpiece Seal
PTFE PTFE
5. Ball Stainless SteelASTM A276, Type 316
Stainless SteelASTM A276, Type 316
6. Stem Stainless SteelASTM A276, Type 316
Stainless SteelASTM A276, Type 316
7. Handle Nut
Stainless Steel18-8 Commercial
Stainles Steel18-8 Commercial
8. Gland Stainless STeelASTM A276, Type 316
Stainless Steel ASTM A276, Type 316
9. Packing Graphite Graphite
10. Thrust Washer
Reinforced PTFE25% Glass Filled
Reinforced PTFE25% Glass Filled
11. Handle-Oval
Carbon Steel1010 Commercial
Carbon Steel1010 Commercial
11A. Handle-Latch-Lock
Stainless Steel Stainless Steel
12. Lockwasher Stainless Steel Stainless Steel
Dimensions ChartFull Port A B C D D1 E E1 F F1 G G1 H H1 J J1 K L P R S
1/4, 3/8, 1/2
.50 1.52 2.72 - 2.41 2.08 2.89 5.8 4.6 - 1.56 - 1.00 - .28 - 5.1 1.34 .275 .32
3/4 .87 2.38 3.37 1.71 - 2.65 2.78 7.6 4.9 2.56 - .578 - 1/4-20 - .28MIN 6.5 1.97 .355 .60
1 1.00 2.51 3.69 1.65 - 2.79 3.91 7.6 4.9 2.83 - .953 - 1/4-20 - .28MIN 6.9 2.31 .355 .60
1-1/4 1.25 3.08 3.93 1.88 - 3.51 - 10.0 - 2.83 - .953 - 1/4-20 - .28MIN 7.2 2.63 .451 .63
1-1/2 1.50 3.32 5.00 1.82 - 3.75 - 10.0 - 2.75 - 1.719 - 1/4-20 - .28MIN 8.5 3.25 .451 .63
2 2.00 3.73 5.57 1.79 - 4.16 - 10.0 - 2.75 - 1.719 - 1/4-20 - .28MIN 9.4 3.81 .451 .63
BAL-5
Rev 09/18
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
34F20CS/F20SS Class 150/300 8" - 12"
Features & BenefitsF20CS/F20SS Class 150/300 1" - 3"F20CS/F20SS Class 150/300 4" - 6"
IndexF20 Series Ball Valve
12
34F20CS/F20SS Class 150/300 8" - 12"
Features & BenefitsF20CS/F20SS Class 150/300 1" - 3"F20CS/F20SS Class 150/300 4" - 6"
IndexF20 Series Ball Valve
12
Rev. 09/18
MILWAUKEE VALVE
1
F20 Series Ball ValveMilwaukee Valve CompanyF20CS/F20SS CLASS 150/300
2 Piece Full Port Flanged Ball Valve
Features and Benefits • Locking lever for safety lockout • Live loaded packing for extended service• Vented ball in ball slot for cavity venting • Standard grounded ball and stem • ISO 5211 mounting pad for easy actuation • Spiral wound graphite and stainless body seal • NACE compliant fasteners for sour gas service • Blow-out proof stem • Fire-safe to API 607 6th edition latest revision • Pressure relieving seat design • Meets all of the latest: API, ASTM/ASME
standards
Operators Available • Locking Lever Handle • Gear operated • Pneumatic and Electric Actuation
Materials of Construction • Carbon steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Body: WCB Stainless • Seats: Reinforced PTFE/or NXT (M-PTFE) • Packing: Graphite
Specification• Valve Sizes 1” thru 12” * • ASME/ANSI Class 150/300 • B.16.34 design • API 608 design • API 607 Firesafe 6th edition • API 598, MSS SP-72 • NACE MR0175
Pressure Ratings: Class 150 Class 300 Carbon Steel 285 psi 740 psi Stainless Steel 275 psi 720 psi
Valve is rated 150 steam @ 365 degrees F.
0
100
200
300
400
500
600
700
800
0 100 200 300 400 500 600
Pres
sure
PSI
G
Temperature Degrees Fahrenheit
Pressure/Temperature Chart
PEEKSEAT
Milwaukee Valve Company16550 West Stratton DriveNew Berlin, WI 53151Phone 262 432 2800Fax 262 432 2701
Milwaukee Valve F20 Top Level Matrix
Revision C
Milwaukee Valve ConfidentialMTV F20 2pc Flg Ball Valve Top Level Matrix rev 0213 LP.xlsx 7/26/06 Page 1
SeriesANSI Class Body Material Ball / Stem Material Seat Material Operator Internal Options Size
XXX X X X X X XXX XXXXF20 1-150 C-Carbon Steel (WCB) S-Stainless Steel (316) N-NXT 2-Lever A-Assemble Dry 100 - 1"
3-300 S-Stainless Steel (CF8M) M-Monel (400) 1-Virgin PTFE 3-Gear Operator V-Vented Ball 112 - 1-1/2" 2-Reinforced PTFE O-Oxygen Clean 200 - 2"
3-Multi-Fill PTFE C-Chlorine Clean 212 - 2-1/2"F- Flat Faced Flg. 300 - 3"T - PTFE Pkg. 400 - 4"
600 - 6"800 - 8"1000 - 10"1200 - 12"
F20 1 C S N 3 A 100
How To Order Milwaukee Valve F20 Series Full Port Two Piece Flanged Ball Valve
150 Class, Carbon Steel Body,Stainless Steel Ball & Stem, NXT Seats, Gear Operator,Assembled Dry 1"
* 1/2" & 3/4" - See F90/91 Series
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
2
Material ListItem Qty. Description F20 Class 150/300
SS ATSM A351 GR CF8MCS ASTM A216 GR WCB
2 1 Ball SS ASTM A351 GR CF8M3 1 Stem ASTM A479 Type 316
CS ASTM A216 GR WCBSS ASTM A351 GR CF8M
NXT M-PTFE03-MULTI FILLED/TFE/GRAPHITE
02-RPTFE6 1 Thrust Washer7 3 Graphite Packing Graphite8 1 Packing Gland ASTM A479 Type 3169 1 Body Seal ASTM A240 TY 304 & Graphite
10 1 Handle Assy Stainless Steel10.1 1 Handle ASTM A276 Type 30410.2 1 Latch ASTM A276 Type 30411 1 Lock Tab ASTM A276 Type 30412 4 Body Stud ASTM A194 GR8 Type 30413 4 Body Stud Nut ASTM A193 GR B8 Type 30414 2 Belleville Washer ASTM A276 Type 30415 1 Lock Washer ASTM A582 Type 30316 2 Stem Nut ASTM A194 GR8 Type 30417 2 Packing End Ring Graphite18 2 Stop Pin ASTM A276 Type 304
Body
Tail Pieces
Seat Materials
11
4 1
5 2
NXT M-PTFE
Class 150 # DimensionsSize Dim. A B C D E F G H J (B.C.) K (BORE) L (QTY) M N
in. 6.2 2.56 4.33 2.3 5 2.36 3.34 4.31 3.13 1 0.63 (4)mm. 157.5 65 110 58.5 127 60 84.9 109.4 79.4 25.4 15.9in. 8.91 3.54 4.92 2.85 6.5 2.95 4.07 4.95 3.87 1.5 0.63 (4)
mm. 226.4 90 125 72.5 165 75 103.4 125.7 98.4 38.1 15.9in. 8.91 3.54 5.91 3.09 7.01 3.54 4.66 5.54 4.75 2 0.75 (4)
mm. 226.4 90 150 78.5 178 90 118.4 140.7 120.7 50.8 19.1in. 8.95 3.54 7.09 3.35 7.48 3.94 5.29 6.11 5.5 2.5 0.75 (4)
mm. 227.3 90 180 85 190 100 134.4 155.2 139.7 63.5 19.1in. 8.95 3.54 7.48 3.41 8 4.72 6.09 6.94 6 3 0.75 (4)
mm. 227.3 90 190 86.5 203 120 154.6 176.3 152.4 76.2 19.5
Class 300 # DimensionsSize Dim. A B C D E F G H J(B.C) K (BORE) L (QTY) M N
in. 6.2 2.56 4.92 3.25 6.5 2.36 3.34 4.17 3.5 1 0.75 (4)mm. 157.5 65 125 82.5 165 60 84.9 106 88.9 25.4 19.1in. 8.91 3.54 6.1 3.35 7.51 2.95 4.07 4.86 4.55 1.5 0.88 (4)
mm. 226.4 90 155 85 190.7 75 103.4 123.5 114.3 38.1 22.2in. 8.91 3.54 6.5 3.31 8.5 3.54 4.66 5.59 5 2 0.75 (8)
mm. 226.4 90 165 84 216 90 118.4 142 127 50.8 19.1in. 8.95 3.54 7.48 4.74 9.49 3.94 5.29 6.15 5.87 2.5 0.88 (8)
mm. 227.3 90 190 120.5 241 100 134.4 156.3 149.2 63.5 22.2in. 8.95 3.54 8.27 5.55 11.1 4.72 6.09 6.6 6.63 3 0.88 (8)
mm. 227.3 90 210 141 282 120 154.6 174.1 168.3 76.2 22.23
1
1 1/2
2
2 1/2
3
2
2 1/2
2X45.0 8x90
2X45.0 8x90
1
1 1/2
2X45.0
2X45.0
2X45.0
8x90
8x90
8x90
16X45
16X45
2X45.0
2X45.0
2X22.5
2X22.5
2X22.5
8x90
8x90
16X45
Class 150 # DimensionsSize Dim. A B C D E F G H J (B.C.) K (BORE) L (QTY) M N
in. 6.2 2.56 4.33 2.3 5 2.36 3.34 4.31 3.13 1 0.63 (4)mm. 157.5 65 110 58.5 127 60 84.9 109.4 79.4 25.4 15.9in. 8.91 3.54 4.92 2.85 6.5 2.95 4.07 4.95 3.87 1.5 0.63 (4)
mm. 226.4 90 125 72.5 165 75 103.4 125.7 98.4 38.1 15.9in. 8.91 3.54 5.91 3.09 7.01 3.54 4.66 5.54 4.75 2 0.75 (4)
mm. 226.4 90 150 78.5 178 90 118.4 140.7 120.7 50.8 19.1in. 8.95 3.54 7.09 3.35 7.48 3.94 5.29 6.11 5.5 2.5 0.75 (4)
mm. 227.3 90 180 85 190 100 134.4 155.2 139.7 63.5 19.1in. 8.95 3.54 7.48 3.41 8 4.72 6.09 6.94 6 3 0.75 (4)
mm. 227.3 90 190 86.5 203 120 154.6 176.3 152.4 76.2 19.5
Class 300 # DimensionsSize Dim. A B C D E F G H J(B.C) K (BORE) L (QTY) M N
in. 6.2 2.56 4.92 3.25 6.5 2.36 3.34 4.17 3.5 1 0.75 (4)mm. 157.5 65 125 82.5 165 60 84.9 106 88.9 25.4 19.1in. 8.91 3.54 6.1 3.35 7.51 2.95 4.07 4.86 4.55 1.5 0.88 (4)
mm. 226.4 90 155 85 190.7 75 103.4 123.5 114.3 38.1 22.2in. 8.91 3.54 6.5 3.31 8.5 3.54 4.66 5.59 5 2 0.75 (8)
mm. 226.4 90 165 84 216 90 118.4 142 127 50.8 19.1in. 8.95 3.54 7.48 4.74 9.49 3.94 5.29 6.15 5.87 2.5 0.88 (8)
mm. 227.3 90 190 120.5 241 100 134.4 156.3 149.2 63.5 22.2in. 8.95 3.54 8.27 5.55 11.1 4.72 6.09 6.6 6.63 3 0.88 (8)
mm. 227.3 90 210 141 282 120 154.6 174.1 168.3 76.2 22.23
1
1 1/2
2
2 1/2
3
2
2 1/2
2X45.0 8x90
2X45.0 8x90
1
1 1/2
2X45.0
2X45.0
2X45.0
8x90
8x90
8x90
16X45
16X45
2X45.0
2X45.0
2X22.5
2X22.5
2X22.5
8x90
8x90
16X45
F20CS/F20SS CLASS 150/300 1"-3"
Rev. 4
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
3
Material ListItem Qty. Description F20 Class 150/300
Stainless Steel A351 GR CF8MCS ASTM A216 GR WCB
2 1 Ball SS ASTM A351 GR CF8M3 1 Stem ASTM A479 Type 316
SS ASTM A351 GR CF8MCS ASTM A216 GR WCB
NXT M-PTFE03-MULTI FILLED/TFE/GRAPHITE
02-RPTFE6 1 Thrust Washer7 4 Graphite Packing Graphite8 1 Packing Gland ASTM A479 Type 3169 1 Body Seal ASTM A240 TY 304 & Graphite
10 1 Handle Assy Ductile Iron ASTM A536 GR. 65-45-1211 1 Snap Ring ASTM A276 Type 30412 8 Body Stud ASTM A193 GR B8 Type 30413 8 Body Stud Nut ASTM A194 GR 8 Type 30414 1 Lock Washer ASTM A582 Type 30315 2 Gland Bolt ASTM A193 GR B8 Type 30416 1 Stop SS ASTM A240 TY30417 2 Packing End Ring Graphite18 1 Packing Plate SS ASTM A351 GR CF8M19 1 Stem Nut ASTM A194 GR8 Type 30420 4 Belleville Washer ASTM A276 Type 304
Body
Tail pieces
Seat Materials
1 1
4 1
5 2
NXT M-PTFE
Class 150 # DimensionsSize Dim. A B C D E F G H J (B.C.) K BORE L (QTY) M N
in. 14.3 3.78 9.06 4.11 9.02 5.83 8.2 9.67 7.5 4 0.75 (8)mm. 358.8 96 230 104.5 229 148 208.4 245.7 190.5 101.6 19in. 25.13 4.92 11.02 7.76 15.51 7.87 10.6 11.79 9.5 6 0.88 (8)
mm. 25.13 125 280 197 394 200 269.2 299.4 241.3 152.4 22.2
Class 300 # DimensionsSize Dim. A B C D E F G H J (B.C.) K BORE L (QTY) M N
in. 14.3 3.78 10.04 6 12.01 5.83 8.2 9.7 7.87 4 0.88 (8)mm. 358.8 96 255 152.5 305 148 208.4 246.3 200 101.6 22.2in. 25.13 4.92 12.6 7.93 15.8 15.87 10.56 10.56 10.63 6 1.03 (8)
mm. 25.13 125 320 201.5 403 403 268.2 268.2 269.9 152.4 26
4
6
6
4 2X22.5
2X22.5
16X45
16X45
2X22.5 16X45
2X22.5 16X45
Class 150 # DimensionsSize Dim. A B C D E F G H J (B.C.) K BORE L (QTY) M N
in. 14.3 3.78 9.06 4.11 9.02 5.83 8.2 9.67 7.5 4 0.75 (8)mm. 358.8 96 230 104.5 229 148 208.4 245.7 190.5 101.6 19in. 25.13 4.92 11.02 7.76 15.51 7.87 10.6 11.79 9.5 6 0.88 (8)
mm. 25.13 125 280 197 394 200 269.2 299.4 241.3 152.4 22.2
Class 300 # DimensionsSize Dim. A B C D E F G H J (B.C.) K BORE L (QTY) M N
in. 14.3 3.78 10.04 6 12.01 5.83 8.2 9.7 7.87 4 0.88 (8)mm. 358.8 96 255 152.5 305 148 208.4 246.3 200 101.6 22.2in. 25.13 4.92 12.6 7.93 15.8 15.87 10.56 10.56 10.63 6 1.03 (8)
mm. 25.13 125 320 201.5 403 403 268.2 268.2 269.9 152.4 26
4
6
6
4 2X22.5
2X22.5
16X45
16X45
2X22.5 16X45
2X22.5 16X45
F20CS/F20SS CLASS 150/300 4"-6"
Rev. 3
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
4
Material list003/051 ssalC 02FnoitpircseDytQmetI
1 1 BODY STAINLESS STEEL A351 GR CF8MCARBON STEEL ASTM A216 GR WCB
M8FC RG 153A MTSA SSLLAB12613 EPYT 974A MTSAMETS13
4 1 TAIL PIECE STAINLESS STEEL A351 GR CF8MCARBON STEEL ASTM A216 GR WCB
5 2 SEAT NXT 75 M-PTFE03-MULTI FILLED/TFE/GRAPHITE
EFTP-M 57 TXN REHSAW TSURHT16ETIHPARGGNIKCAP METS47
613 EPYT 974A MTSADNALG189 1 BODY SEAL ASTM A240 TYPE 304 & GRAPHITE
LEETS NOBRACRAEG10111 1 STEM KEY C.D.STEEL-11L41, 1045 ANNEALED12 SET STUD BOLT ASTM A193 GR B8 TYPE 304
403 RPYT 8 RG 491A MTSATUNTES3114 4 WASHER CHROME-VANADIUM STEEL GR. 6150
613 EPYT 672A MTSAREHSAW KCOLTES51613 EPYT 672A MTSATLOBTES61
17 2 GLAND BOLT ASTM A193 GR B8 TYPE 304ETIHPARGGNIR DNE GNIKCAP281
19 1 PACKING PLATE SS ASTM A351 GR CF8M20 1 GEAR BRACKET CS; ASTM A216 GR WCB
21 1 BALL SUPPORT BOOSTER BEARING 15%GLASS FILLED REINFORCE TEFLON
22 1 BALL SUPPORT HOLDER ASTM A276 TYPE 316
23 1 BALL SUPPORT BOOSTER 15% GLASS FILLED REINFORCE TEFLON
ETIHPARGGNIKCAP ETIHPARG14225 1 BALL SUPPORT GLAND ASTM A276 TYPE 31626 1 BODY STUD NUT ASTM A194 GR 8 TYPE 30427 1 BALL SUPPORT BOLT ASTM A193 GR B8
Class 150 # DimensionsSize Dim. A B C D E F G H J K L M N (B.C.) P (QTY) Q R
in. 6.77 13.58 7.72 8 8.52 17.99 9.96 17.25 6.14 18.36 7.91 11.81 11.75 1.16 (16)mm. 172 245 196 203.2 216.5 457 253.1 438.2 156 466.4 200.9 300 298.5 29.4in. 10.16 15.94 11.34 10 9.86 20.98 12.31 20.96 6.14 21.63 12.6 1425 14.25 1.16 (24)
mm. 258 405 288 254 250.5 533 312.8 532.4 156 549.4 320.1 362 362 29.4in. 10.24 19.09 11.34 11.63 24.02 24.02 13.96 22.35 6.14 25.84 12.28 17 17 1.16 (24)
mm. 260 485 288 295.5 610 610 610 567.7 156 656.3 311.9 431.8 431.8 29.4
Class 300 # DimensionsSize Dim. A B C D E F G H J K L M N (B.C.) P (QTY) Q R
in. 6.77 14.96 7.72 8 9.11 19.76 9.96 17.25 6.14 18.64 7.91 13 13 1.16 (24)mm. 172 380 196 203.2 231.5 502 253.1 438.2 156 473.4 200.9 330.2 330.2 29.4in. 10.16 12.75 11.34 10 10.26 22.36 12.31 20.96 6.14 21.94 12.6 15.25 15.25 1.28 (32)
mm. 258 323.8 288 254 260.5 568 312.8 532.4 156 557.4 320.1 387.4 387.4 32.6in. 10.24 15 11.34 11.63 12.24 25.51 13.96 22.35 6.14 26.1 12.28 17.75 17.75 1.41 (32)
mm. 260 381 288 295.5 311 648 610 567.7 156 665.3 311.9 450.8 450.8 35.7
10
12
8
8
10
12
2X11.25
16X45
24X30
24X30
24X30
32X22.5
32X2.5
2X22.5
2X15
2X15
2X15
2X11.25
Class 150 # DimensionsSize Dim. A B C D E F G H J K L M N (B.C.) P (QTY) Q R
in. 6.77 13.58 7.72 8 8.52 17.99 9.96 17.25 6.14 18.36 7.91 11.81 11.75 1.16 (16)mm. 172 245 196 203.2 216.5 457 253.1 438.2 156 466.4 200.9 300 298.5 29.4in. 10.16 15.94 11.34 10 9.86 20.98 12.31 20.96 6.14 21.63 12.6 1425 14.25 1.16 (24)
mm. 258 405 288 254 250.5 533 312.8 532.4 156 549.4 320.1 362 362 29.4in. 10.24 19.09 11.34 11.63 24.02 24.02 13.96 22.35 6.14 25.84 12.28 17 17 1.16 (24)
mm. 260 485 288 295.5 610 610 610 567.7 156 656.3 311.9 431.8 431.8 29.4
Class 300 # DimensionsSize Dim. A B C D E F G H J K L M N (B.C.) P (QTY) Q R
in. 6.77 14.96 7.72 8 9.11 19.76 9.96 17.25 6.14 18.64 7.91 13 13 1.16 (24)mm. 172 380 196 203.2 231.5 502 253.1 438.2 156 473.4 200.9 330.2 330.2 29.4in. 10.16 12.75 11.34 10 10.26 22.36 12.31 20.96 6.14 21.94 12.6 15.25 15.25 1.28 (32)
mm. 258 323.8 288 254 260.5 568 312.8 532.4 156 557.4 320.1 387.4 387.4 32.6in. 10.24 15 11.34 11.63 12.24 25.51 13.96 22.35 6.14 26.1 12.28 17.75 17.75 1.41 (32)
mm. 260 381 288 295.5 311 648 610 567.7 156 665.3 311.9 450.8 450.8 35.7
10
12
8
8
10
12
2X11.25
16X45
24X30
24X30
24X30
32X22.5
32X2.5
2X22.5
2X15
2X15
2X15
2X11.25
F20CS/F20SS CLASS 150/300 8"-12"
Rev. 2
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
0
100
200
300
400
500
600
700
800
0 100 200 300 400 500 600
Pres
sure
PSI
G
Temperature Degrees Fahrenheit
Pressure/Temperature Chart
PEEKSEAT
Pressure Ratings: Class 150 Class 300Carbon Steel 285 psi 740 psiStainless Steel 275 psi 720 psi
Milwaukee Valve Company16550 West Stratton DriveNew Berlin, WI 53151Phone 262 432 2800Fax 262 432 2701
Milwaukee Valve F20 Top Level Matrix
Revision C
Valve Series Body Material Ball/Stem Material End Connection Port Size Seat Material External Options Internal Options SizeXXX X X XXX X XX XXX XX XXX
F90 Non-fire-safe C-Carbon Steel (WCB) C-Carbon Steel (WCB) 150 = ANSI 150 Flanged R = Standard Port N1 -NXT OS-Stainless Oval AD-Assemble Dry 1/2F91 Fire safe S-Stainless Steel (CF8M) S-Stainless Steel (CF8M) 300 = ANSI 300 Flanged 01-Virgin PTFE XH-Extended Handle CC-Chlorine Cleaned 3/4
M-Monel M-Monel 02-Reinforced PTFEOH-Carbon Oval OC-Oxygen Cleaned 1H-Hastalloy-C H-Hastalloy-C 03-Multi-Fill PTFE XLH-Extended Locking GB-Grounded Ball 112
06-Peek GO- Gear Operator VB-Vented Ball 2346
How To Order Milwaukee Valve F90/F91 Series Unibody Flanged Ball Valve
F91CS150RN1 100 - (1" Class Fire-safe, Flanged 150 Carbon Steel Body, Stainless Trim, NXT Seats, Lever)Example Product Numbers
Milwaukee Valve ConfidentialMTV F91 1pc Flg Ball Valve Top Level Matrix LP.xls 7/26/06 Page 1
F90/91 SERIES Ball Valve Milwaukee Valve Company F90/91CS/SS Class 150/300 Unibody Standard Port Flanged Ball Valve
Features and Benefits
• Locking lever for safety lockout • 2 bolt adjustable stem packing arrangement for longer packing life • Vented ball in ball slot for cavity venting • Optional grounded ball and stem • Four bolt actuator mounting pad for easy actuation • NACE Compliant for sour gas service • Blow-out proof stem design • Fire-safe to API 607 (F91) • Pressure relieving seat design • Meets API, ASTM, ASME and MSS standards
Operators Available
• Locking lever handle, Oval handle, Gear operated • Pneumatic and Electric Actuation
Materials of Construction
• Body: Carbon steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Stainless • Seats: STD (NXT-75) or ME-PTFE • Packing: Graphite or PTFE
Specifications
• Valves Sizes 1/2” through 6” • ASME/ANSI Class 150/300 • Meets ASME B16.34 design • Valves meet API 608 • Valves meet API 607 for Fire safe testing (F91) • Valves tested to API 598 and MSS SP-72 Valve is rated 150 steam @ 365 degrees F • Valves meet NACE MRO175
F90/91 SERIES Ball Valve Milwaukee Valve Company F90/91CS/SS Class 150/300 Unibody Standard Port Flanged Ball Valve
Features and Benefits
• Locking lever for safety lockout • 2 bolt adjustable stem packing arrangement for longer packing life • Vented ball in ball slot for cavity venting • Optional grounded ball and stem • Four bolt actuator mounting pad for easy actuation • NACE Compliant for sour gas service • Blow-out proof stem design • Fire-safe to API 607 (F91) • Pressure relieving seat design • Meets API, ASTM, ASME and MSS standards
Operators Available
• Locking lever handle, Oval handle, Gear operated • Pneumatic and Electric Actuation
Materials of Construction
• Body: Carbon steel or CF8M Stainless Steel • Ball: 316 Stainless • Stem: 316 Stainless • Seats: STD (NXT-75) or ME-PTFE • Packing: Graphite or PTFE
Specifications
• Valves Sizes 1/2” through 6” • ASME/ANSI Class 150/300 • Meets ASME B16.34 design • Valves meet API 608 • Valves meet API 607 for Fire safe testing (F91) • Valves tested to API 598 and MSS SP-72 Valve is rated 150 steam @ 365 degrees F • Valves meet NACE MRO175
Valve Size
Class 150(0-300 PSID)
Recommended Actuator Torque
(in. lbs. Nm)
Class 150(0-300 PSID)
Recommended Actuator Torque
(in. lbs. Nm)
Class 300 (301-740 PSID) Recommended
Actuator Torque
(in. lbs. Nm)
Cv Valve Size
Class 300 (301-740 PSID) Recommended
Actuator Torque
(in. lbs. Nm)
Cv
1/240 4.5
40 4.5
15 2240 27.1
300 33.9
120
3/460 6.8
60 6.8
25 3500 56.6
750 84.8
460
1125 14.1
125 14.1
37 4900
101.81000 113.1
640
1 1/2190 21.5
190 21.5
90 61900 214.9
3525 398.8
1025
Class 150(0-300 PSID)
Recommended Actuator Torque
(in. lbs. Nm)
Class 150(0-300 PSID)
Recommended Actuator Torque
(in. lbs. Nm)
TORQUE & CV VALUES
Rev 09/18
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
NIN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM
1/2" 0.50 13 4.25 108 2.50 64 3.50 89 5.06 129 0.81 21 1.75 44 0.71 18 0.20 5 0.32 8 2.88 73 1.88 48 5/16 - 183/4" 0.69 18 4.62 117 3.65 93 3.88 99 5.97 152 0.94 24 1.75 44 0.57 15 0.28 7 0.48 12 3.13 80 2.06 52 5/16 - 181" 0.88 22 5.00 127 3.80 97 4.25 108 5.97 152 1.25 32 1.75 44 0.82 21 0.28 7 0.48 12 4.19 106 2.46 63 5/16 - 18
1-1/2" 1.25 32 6.50 165 4.77 121 5.00 127 8.85 225 1.81 46 1.75 44 0.06 2 0.45 12 0.63 16 5.63 143 2.50 64 5/16 - 182" 1.50 38 7.00 178 4.72 120 6.00 152 8.85 225 2.07 52 2.25 57 0.31 8 0.45 12 0.63 16 6.19 157 3.00 76 5/16 - 183" 2.31 59 8.00 203 6.80 172 7.50 191 11.00 279 3.09 79 3.50 89 0.34 9 0.45 12 1.20 31 7.13 181 3.75 95 3/8 - 164" 3.12 79 9.00 229 7.96 202 9.00 229 14.12 359 3.92 100 4.00 102 0.30 8 0.66 17 1.35 34 8.00 203 5.27 134 7/16 - 146" 4.50 114 10.50 267 9.44 240 11.00 279 18.00 457 4.70 119 4.00 102 0.58 15 0.91 23 1.88 48 9.44 240 6.63 168 7/16 - 14
NIN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM
1/2" 0.50 13 5.50 140 2.50 64 3.75 95 5.06 129 0.81 21 1.75 44 0.71 18 0.20 5 0.32 8 4.00 102 1.88 48 5/16 - 183/4" 0.69 18 6.00 152 3.65 93 4.62 117 5.97 152 0.94 24 1.75 44 0.84 21 0.28 7 0.48 12 4.38 111 2.31 59 5/16 - 181" 0.88 22 6.50 165 3.80 97 4.88 124 5.97 152 1.25 32 1.75 44 0.91 23 0.28 7 0.48 12 5.69 145 2.56 65 5/16 - 18
1-1/2" 1.25 32 7.50 191 4.77 121 6.12 155 8.85 225 1.81 46 1.75 44 0.62 16 0.45 12 0.63 16 6.56 167 3.06 78 5/16 - 182" 1.50 38 8.50 216 4.72 120 6.50 165 8.85 225 1.97 50 2.25 57 1.10 28 0.45 12 0.63 16 7.50 191 3.80 97 5/16 - 183" 2.31 59 11.12 282 6.80 172 8.25 209 11.00 279 2.91 74 3.50 89 1.18 30 0.45 12 1.20 31 9.88 251 4.60 117 3/8 - 164" 3.12 79 12.00 305 7.96 202 10.00 254 14.12 359 3.92 100 4.00 102 0.80 20 0.66 17 1.35 34 10.68 271 5.77 147 7/16 - 146" 4.50 114 15.88 403 9.44 240 12.50 318 18.00 457 4.70 119 4.00 102 1.11 28 0.91 23 1.88 48 14.38 365 7.38 188 7/16 - 14
L ME F G H J KSIZE
A B C D
ANSI 150 LB. - DIMENSIONS - INCHES AND MILLIMETERS (90/91 - SERIES BALL VALVES)
ANSI 300 LB. - DIMENSIONS - INCHES AND MILLIMETERS (90/91 - SERIES BALL VALVES)
SIZEA B C D E F G H J K L M
F90/91SS150/300, F90/91CC150/300 AND F90/91CS150/300 FLANGED-END BALL VALVE
F90/F91 Series
Item Qty. Description F90 Class 150/300M8FC RG 447A/153A MSTA SS11
CS ASTM A216 GR WCBM8FC RG 447A/153A MSTA SS12
CS ASTM A216 GR WCB3 1 Stem SS ASTM A276 Type 3164 1 Ball SS ASTM 276 Type 3165 1 Handle Nut SS 18-8
6 1Handle
1/2"-2" SS Type 3043"-6" Ductile Iron
7 1Packing Plate
1/2"-1" SS Type 3041-1/2"-6" ASTM A351 GR CF8M
8 1 Gland Follower SS Type 304
9 1Packing
(F90) PTFE(F91) Graphoil
10 1 Thrust Washer NXT 7511 2 Seat (NXT Standard) NXT 7512 1 Retainer Seal PTFE13 1 Ground Washer Graphite14 1 Bearing, Gland Follower RPTFE
Body
Ball Retainer
NIN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM
1/2" 0.50 13 4.25 108 2.50 64 3.50 89 5.06 129 0.81 21 1.75 44 0.71 18 0.20 5 0.32 8 2.88 73 1.88 48 5/16 - 183/4" 0.69 18 4.62 117 3.65 93 3.88 99 5.97 152 0.94 24 1.75 44 0.57 15 0.28 7 0.48 12 3.13 80 2.06 52 5/16 - 181" 0.88 22 5.00 127 3.80 97 4.25 108 5.97 152 1.25 32 1.75 44 0.82 21 0.28 7 0.48 12 4.19 106 2.46 63 5/16 - 18
1-1/2" 1.25 32 6.50 165 4.77 121 5.00 127 8.85 225 1.81 46 1.75 44 0.06 2 0.45 12 0.63 16 5.63 143 2.50 64 5/16 - 182" 1.50 38 7.00 178 4.72 120 6.00 152 8.85 225 2.07 52 2.25 57 0.31 8 0.45 12 0.63 16 6.19 157 3.00 76 5/16 - 183" 2.31 59 8.00 203 6.80 172 7.50 191 11.00 279 3.09 79 3.50 89 0.34 9 0.45 12 1.20 31 7.13 181 3.75 95 3/8 - 164" 3.12 79 9.00 229 7.96 202 9.00 229 14.12 359 3.92 100 4.00 102 0.30 8 0.66 17 1.35 34 8.00 203 5.27 134 7/16 - 146" 4.50 114 10.50 267 9.44 240 11.00 279 18.00 457 4.70 119 4.00 102 0.58 15 0.91 23 1.88 48 9.44 240 6.63 168 7/16 - 14
NIN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM IN MM
1/2" 0.50 13 5.50 140 2.50 64 3.75 95 5.06 129 0.81 21 1.75 44 0.71 18 0.20 5 0.32 8 4.00 102 1.88 48 5/16 - 183/4" 0.69 18 6.00 152 3.65 93 4.62 117 5.97 152 0.94 24 1.75 44 0.84 21 0.28 7 0.48 12 4.38 111 2.31 59 5/16 - 181" 0.88 22 6.50 165 3.80 97 4.88 124 5.97 152 1.25 32 1.75 44 0.91 23 0.28 7 0.48 12 5.69 145 2.56 65 5/16 - 18
1-1/2" 1.25 32 7.50 191 4.77 121 6.12 155 8.85 225 1.81 46 1.75 44 0.62 16 0.45 12 0.63 16 6.56 167 3.06 78 5/16 - 182" 1.50 38 8.50 216 4.72 120 6.50 165 8.85 225 1.97 50 2.25 57 1.10 28 0.45 12 0.63 16 7.50 191 3.80 97 5/16 - 183" 2.31 59 11.12 282 6.80 172 8.25 209 11.00 279 2.91 74 3.50 89 1.18 30 0.45 12 1.20 31 9.88 251 4.60 117 3/8 - 164" 3.12 79 12.00 305 7.96 202 10.00 254 14.12 359 3.92 100 4.00 102 0.80 20 0.66 17 1.35 34 10.68 271 5.77 147 7/16 - 146" 4.50 114 15.88 403 9.44 240 12.50 318 18.00 457 4.70 119 4.00 102 1.11 28 0.91 23 1.88 48 14.38 365 7.38 188 7/16 - 14
L ME F G H J KSIZE
A B C D
ANSI 150 LB. - DIMENSIONS - INCHES AND MILLIMETERS (90/91 - SERIES BALL VALVES)
ANSI 300 LB. - DIMENSIONS - INCHES AND MILLIMETERS (90/91 - SERIES BALL VALVES)
SIZEA B C D E F G H J K L M
Rev 09/18
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BRONZE AND BRASS BALL VALVES INDEX
BA-100/100S BV-1
BA-100/100S P2 BV-2
BA-100ELD/ BA100SELD BV-3
BA-100H/BA-150H BV-4
BA-100SH/BA150SH BV-5
BA-100H/BA100SH P1 BV-6
BA-100M BV-7
BA-100-TS BV-8
BA-150/150S BV-9
BA-200 BV-10
BA-250 BV-11
BA-300/300S BV-12
BA-300/300S P2 BV-13
BA-300SB/300SBS BV-14
BA-350/350S BV-15
BA-350TE/350STE BV-16
BA-350TE-G/350STE-G BV-17
BA-400/400S BV-18
BA-400/400S P2 BV-19
BA-400S3 BV-20
BA-450/450S BV-21
BA-475B BV-22
BA-485B BV-23
BA-500/550 BV-24
BA-480B BV-25
BA-480S BV-26
BA-480BH BV-27
BA-480SH BV-28
BA-481B BV-29
BA-481S BV-30
BA-490B BV-31
BA-490S BV-32
BA-491B BV-33
BA-491S BV-34
Insulator Handle/MS (TIH) BV-35 - 36
Options BA-100/150/300/350/400/450 BV-37
Options BA-200/250/475B/485B/480B/490B BV-38
Rev 09/18
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-1
*Not intended for use in potable water.MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16
316 Stainless Steel (2) A2764 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (2) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
(1) Milwaukee Valve Company recommends the use of Stainless steel ball and stem for steam applications. Please consult factory for more information. (2) Stem is stainless for BA-100S and 2-1/2”–3” BA-100
B
AD
C
E
34
567
8 11
F
2 1
910O P E N600
WO
G150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY, IN
CR
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE DATA
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
Saturated Steam
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.
232
DIMENSIONS
UNITS1/4”DN6
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
A (DIA)
INCHES 0.38 0.38 0.50 0.76 0.88 1.06 1.31 1.56 2.00 2.31mm 10 10 13 19 22 27 33 40 51 59
BINCHES 1.86 1.86 2.19 2.64 3.17 3.50 3.96 4.30 5.56 6.20mm 46 46 54 65 78 86 97 105 136 152
CINCHES 1.00 1.00 1.10 1.30 1.58 1.74 1.97 2.15 2.79 3.10mm 25 25 27 32 39 43 48 53 68 76
DINCHES 1.78 1.81 1.91 2.08 2.25 2.66 2.84 3.00 3.47 3.90mm 44 44 47 51 55 65 70 74 85 96
EINCHES 3.81 3.81 3.81 4.56 4.56 6.31 6.31 7.19 7.19 7.19mm 93 93 93 112 112 155 155 176 176 176
F THREADSIZE 1/4" NPT 3/8"NPT 1/2" NPT 3/4" NPT 1"NPT 1-1/4"
NPT1-1/2" NPT 2" NPT 2-1/2"
NPT 3" NPT
Cv 7 7 13 30 38 61 87 121 228 305Note: DN (Diameter Nominal) = Metric equivalent size.
Rev. 18
Bronze Ball ValveTwo Piece
Standard Port (1”-3”) Full Port (1/4”-3/4”)600 WOG/150 SWP (1)
Threaded EndsBlow-Out Proof Stem
MSS SP-110
BA-100/100S* ¼”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-2Rev. 4
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Standard Port (1”-3”) Full Port (1/2”-3/4”)200 psig @ 250°F†Press x Press Ends
Press x Threaded Ends Available (Consult Factory)Blow-Out Proof Stem
Conforms to MSS SP-110
BA-100/100S* P2 ½”-3”
/ 2BRONZE BALL VALVETWO-PIECE, FULL-PORT (1/4”-3/4”) STANDARD PORT (1”-2”)200 PSIG @ 250°FPRESS ENDSBLOW-OUT PROOF STEM
AD
E
2
34
567
8
910
11
DIMENSIONS
BA-100 400S* P2 12 -" "
1
MSS SP-110
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
(1) For steam service specify see BA400S3
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
With Press Ends B
12
Press End Adapter (4151 Series)
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
A (DIA)INCHES 0.50 0.76 1.06 1.31 1.56 2.00 2.00 2.31mm 13 19 27 33 40 51 51 59
STD Insertion
INCHES 0.87 0.98 0.98 1.02 1.42 1.58 1.80 2.10mm 22 25 25 26 36 40 46 53
BINCHES 5.19 6.22 7.17 7.57 8.44 10.30 12.02 13.94mm 132 158 182 192 214 262 305 354
DINCHES 1.91 2.32 2.68 2.82 3.00 3.36 3.47 3.88mm 47 59 68 72 76 85 88 99
EINCHES 3.82 4.55 6.33 6.33 6.33 7.19 7.19 7.19mm 94 116 161 161 161 183 183 183
Note: DN (Diameter Nominal)=Metric equivalent size. †Non-Shock
Note: 2 1/2” & 3” are built from BA-150/150S
12
13
1415
E
2
9 101
OP
EN 600
WOG150SWP MILWAUKEE VALVE COMPANY, INC
R
MATERIAL LISTITEM PART MATERIAL ASTM SPEC
1 Body Cast Bronze B584 C84400
2 Tailpiece
Brass B283C37700
Cast Bronze (1 1/4” & up) B584C84400
3 Ball
Brass w/Hard Chrome Plating
B283 C37700
316 Stainless Steel (1) A276 S31600
4 Seat RPTFE, 15% Glass filled
5 Stem
Brass B21 C46400
H02316 Stainless Steel (1) A276
S316006 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B16
C36000H02
9 Handle Steel w/Zinc Plating Commercial10 Handle Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
12 Press AdaptersBrass Fitting w/EPDM O-Ring (1/2" - 2")
B283
Copper (2 1/2” - 3”) B8813 O-Ring EPDM14 Backing Seal Acetal15 Backing Ring 304 Stainless Steel A276
(1) Ball and stem are stainless for BA100S P2
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-3
E
12
10
9
F
OPEN125 WO
G
LIM
WE
EK
UA
VL
AE
VP
MO
CY
NA
,C
NIR
Note: Handle is shown in theopen position. Ball is shownclosed to illustrate vent feature.
D
4
57 8
11
A
FLOWPORTVENT
(.125” DIA)
3
6
FLOWINDICATOR
B
C
C
M
Y
CM
MY
CY
CMY
K
BA100ELD_REV10.PDF 1 8/6/14 2:09 PM
PRESSURE - TEMPERATURE DATA
0 10TEMPERATURE -F
ER
USSERP
-GISP
25
30 40
50
50 60
75
70 80
100
150
125
90
175
20 100 110 120
RECOMMENDED FORXAM.G.I.S.P .521
C
M
Y
CM
MY
CY
CMY
K
DIMENSIONSUNITS
1/4”DN10
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.38 0.38 0.5 0.76 0.88 1.06 1.31 1.56mm 10 10 13 19 22 27 33 40
BINCHES 1.86 1.86 2.19 2.65 3.17 3.50 3.96 4.30mm 47 47 55 67 80 89 101 109
CINCHES 1 1 1.10 1.30 1.58 1.74 1.97 2.15mm 25 25 27 33 40 44 50 55
DINCHES 1.81 1.81 1.91 2.08 2.25 2.66 2.84 3.00mm 46 46 48 53 57 67 72 76
EINCHES 3.82 3.82 3.82 4.84 4.84 6.35 6.35 7.20mm 97 97 97 123 123 161 161 183
F THREADSIZE 1/4" NPT 3/8"NPT 1/2" NPT 3/4" NPT 1"NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 7 7 12 30 38 61 87 121Note: DN (Diameter Nominal) = Metric equivalent size.
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16
316 Stainless Steel (1) A2764 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (2) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
(1) Ball & Stem are stainless for BA-100SELD.
Rev. 16
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Standard Port (1”-2”) Full Port (1/4”-3/4”)Safety ExhaustLocking Handle
Blow-Out Proof StemMSS SP-110
BA-100ELD/BA-100SELD* ¼”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-4
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Bronze B5842 Tailpiece Brass B16
3 Ball Brass w/Hard Chrome Plating B16
4 Seat RPTFE, 15% Glass Filled5 Stem Brass B166 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial12 Dust Cap Polyproplyene13 Gasket EPDM14 Chain Brass Bead
NOTE: Pressure / Temperature ratings shown are for valve only. Hose side pressure and temperature limit is based on connected hose and is the users responsibility.
DIMENSIONSUNITS
1/2”DN15
3/4”DN20
ØAINCHES 0.50 0.76mm 13 19
B (BA-100)
INCHES 2.70 2.90mm 69 74
B’(BA-150)
INCHES 2.55 3.05mm 65 78
C(BA-100)
INCHES 1.10 1.30mm 28 33
C’(BA-150)
INCHES 1.10 1.45mm 28 37
DINCHES 1.88 2.14mm 48 54
EINCHES 3.81 4.62mm 97 117
F THREADEDINLET NPT NPT
Cv 13 30Note: DN (Diameter Nominal) = Metric equivalent size.
Do not pressurize cap.Pressure not to exceed 40 psi.
690
1380
2070
2760
4140
3450
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE DATA
100
200
300
400
600
500
0 50 150 200 250 300 350 400100
GNIKRO
WERUSSERP
-pKa
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material RatingJoint Limits fromANSI B16.18 for 95/5 Solder
93
450
232
(See Note)
BA100HA_REV10.PDF 10/9/2008 9:35:02 AM
BA100HA_REV10.PDF 1 3/4/14 9:22 AM
Rev. 17
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece Full Port
Threaded x 3/4” Hose End (BA100H)Solder x 3/4” Hose End (BA150H)
Dust Cap and ChainBlow-Out Proof Stem
MSS SP-110
BA-100H/150H* ½”-¾”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-5
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Bronze B5842 Tailpiece Brass B163 Ball 316 Stainless Steel A2764 Seat RPTFE, 15% Glass Filled5 Stem 316 Stainless Steel A2766 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial12 Dust Cap Polyproplyene13 Gasket EPDM14 Chain Brass Bead
NOTE: Pressure / Temperature ratings shown are for valve only. Hose side pressure and temperature limit is based on connected hose and is the users responsibility.
DIMENSIONSUNITS
1/2”DN15
3/4”DN20
ØAINCHES 0.50 0.76mm 13 19
B (BA-100)
INCHES 2.70 2.90mm 69 74
B’(BA-150)
INCHES 2.55 3.05mm 65 78
C(BA-100)
INCHES 1.10 1.30mm 28 33
C’(BA-150)
INCHES 1.10 1.45mm 28 37
DINCHES 1.88 2.14mm 48 54
EINCHES 3.81 4.62mm 97 117
F THREADEDINLET NPT NPT
Cv 13 30Note: DN (Diameter Nominal) = Metric equivalent size.
Do not pressurize cap.Pressure not to exceed 40 psi.
690
1380
2070
2760
4140
3450
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE DATA
100
200
300
400
600
500
0 50 150 200 250 300 350 400100
GNIKRO
WERUSSERP
-pKa
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material RatingJoint Limits fromANSI B16.18 for 95/5 Solder
93
450
232
(See Note)
BA100HA_REV10.PDF 10/9/2008 9:35:02 AM
BA100HA_REV10.PDF 1 3/4/14 9:22 AM
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece • Full Port
Threaded x 3/4” Hose End (BA100SH)Solder x 3/4” Hose End (BA150SH)
Dust Cap and ChainBlow-Out Proof Stem
MSS SP-110
BA-100SH/150SH* ½”-¾”
Rev. 2
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-6
B
Press End Adapter (4151 Series)
15
Do not pressurize cap.Pressure not to exceed 40 psi.
MATERIAL LISTITEM PART MATERIAL ASTM SPEC
1 Body Bronze B5842 Tailpiece Brass B16
3 BallBrass w/Hard Chrome Plating
B16
316 Stainless Steel (1) A2764 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (1) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial12 Dust Cap Polyproplyene13 Gasket EPDM14 Chain Brass Bead
15 Press Adapters Brass Fitting w/EPDM O-Ring B283
+NON-SHOCK(1) Ball & Stem are stainless steel for BA100SH P1
DIMENSIONS
UNITS1/2” 3/4”
DN15 DN20
A INCHESmm
0.50 13
.7619
B INCHESmm
2.7069
2.9074
STDINSERTION
DEPTH
INCHESmm
.8722
.9825
C INCHESmm
1.1028
1.3033
D INCHESmm
1.8848
2.1454
E INCHESmm
3.8197
4.62117
F THREAD INLET NPT NPT
Cv 13 30
Note: DN (Diameter Nominal) = Metric equivalent size.
Rev. 5
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece Full Port
200 psig @ 250°F†Press x Hose End
Dust Cap and ChainBlow-Out Proof Stem
Conforms to MSS SP-110
BA-100H/100SH P1 ½”-¾”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-7
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B5842 Tailpiece Brass/Bronze (1" & up) B16/B5843 Ball Brass w/Hard Chrome Plating B164 Seat RPTFE, 15% Glass Filled5 Stem Brass B166 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
* Please consult factory for more information regarding steam applications.
DIMENSIONS
UNITS1/4”DN6
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.38 0.38 0.50 0.76 0.88 1.06 1.31 1.56mm 10 10 13 19 22 27 33 40
BINCHES 2.50 2.52 2.80 3.22 3.64 4.24 4.69 4.95mm 64 64 71 82 93 108 119 126
CINCHES 1.00 1.00 1.09 1.30 1.59 1.75 1.97 2.15mm 25 25 28 33 40 45 50 55
DINCHES 1.76 1.76 1.87 2.20 2.28 2.67 2.77 3.00mm 45 45 48 56 58 68 70 77
EINCHES 3.79 3.79 3.80 4.55 4.54 6.32 6.32 7.20mm 96 96 96 116 115 161 161 183
F THREADSIZE 1/4" NPT 3/8"NPT 1/2" NPT 3/4" NPT 1"NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 11 11 17 30 40 52 90 115Note: DN (Diameter Nominal) = Metric equivalent size.
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE CHART
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.
232
FLOWPORT
B
AD
C
E
12
34
5 F6
7
8
910
11
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
Rev. 12
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Standard Port (1”-2”) Full Port (1/4”-3/4”)600 WOG/150 SWP*
FNPT x MNPT ConnectionsBlow-Out Proof Stem
MSS SP-110
BA-100-M* ¼”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-8
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B5842 Tailpiece Brass/Bronze (1" & up) B16/B5843 Ball Brass w/Hard Chrome Plating B164 Seat RPTFE, 15% Glass Filled5 Stem Brass B166 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
* Please consult factory for more information regarding steam applications.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.50 0.76 0.88 1.06 1.31 1.56mm 13 19 22 27 33 40
BINCHES 2.16 2.91 3.53 4.00 4.46 5.27mm 55 74 90 102 113 134
CINCHES 1.07 1.30 1.58 1.74 1.97 2.15mm 27 33 40 44 50 55
DINCHES 1.87 2.08 2.25 2.66 2.84 3.00mm 48 53 57 67 72 76
EINCHES 3.19 4.84 4.84 6.35 6.35 7.20mm 81 123 123 161 161 183
F THREADSIZE 1/2" NPT 3/4"NPT 1" NPT 1-1/4"
NPT1-1/2” NPT 2" NPT
Cv 13 30 40 52 90 115Note: DN (Diameter Nominal) = Metric equivalent size.
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE DATA
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.
232
FLOWPORT
B
AD
C
E
12
34
5 F6
7
8
910
11
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
C
M
Y
CM
MY
CY
CMY
K
BA100TS_REV9.PDF 1 11/16/15 9:06 AM
Rev. 19
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Standard Port (1”-2”) Full Port (1/2”-3/4”)600 WOG
Threaded x Solder EndsBlow-Out Proof Stem
MSS SP-110
BA-100-TS* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-9
DIMENSIONS
UNITS3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
A (DIA)
INCHES 0.38 0.50 0.76 0.88 1.06 1.31 1.56 2.00 2.31mm 10 13 19 22 27 33 40 51 59
BINCHES 2.10 2.39 3.05 3.71 4.54 5.00 6.25 7.34 8.16mm 52 59 75 91 111 123 153 180 200
CINCHES 0.90 1.07 1.56 1.76 2.27 2.50 3.13 3.67 4.07mm 22 26 38 43 56 61 77 90 100
DINCHES 1.80 1.89 2.13 2.29 2.67 2.85 3.02 3.47 3.88mm 44 46 52 56 65 70 74 85 95
EINCHES 3.81 3.81 4.56 4.56 6.31 6.31 7.19 7.19 7.19mm 93 93 112 112 155 155 176 176 176
F TUBESIZE 0.51 0.63 0.88 1.13 1.38 1.63 2.13 2.63 3.13
Cv 7 13 35 38 61 87 121 228 305Note: DN (Diameter Nominal) = Metric equivalent size.
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16
316 Stainless Steel (1) A2764 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (1) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
(1) Stem is stainless for BA-150S and 2-1/2”–3” BA-150.
505
270
485
395
210
325
175
0
100
200
300
400
500
600
700
0 50 100 150 200 250
PRESSURE
psig
TEMPERATURE, Degrees FSolder Joint And Service As Per ANSI B16.18
PRESSURE VS TEMP. (based on 95/5 solder)
3/8 thru 1"
1 1/4 thru 2"
2 1/2 thru 4"
600
4” Only
B
A
F
D
C
E
2
910
11
1
57
34
6
8
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
B
A
F
D
C
E
2
910
11
1
57
34
6
8
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
Rev. 18
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Standard Port (1”-3”) Full Port (3/8”-3/4”)600 WOG
Solder EndsBlow-Out Proof Stem
MSS SP-110
BA-150/150S* ⅜”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-10
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass,Forged B2832 Tailpiece Brass,Forged B283
3 BallBrass,CP B283Brass CP, Cast B584
4 Seat PTFE5 Stem Brass B1246 Thrust Washer PTFE7 Gland Nut Brass B168 Gland Packing PTFE9 Handle Steel w/Zinc Plating Commercial
10 Handle Nut Brass B16
DIMENSIONS
UNITS1/4”DN6
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
4”DN100
A (DIA)
INCHES 0.31 0.31 0.39 0.59 0.76 0.98 1.26 1.50 2.00 2.52 2.95mm 8 8 10 15 19 25 32 38 51 64 75
BINCHES 1.65 1.65 2.30 2.55 3.05 3.43 3.76 4.21 5.50 6.22 7.31mm 42 42 58 65 78 87 96 107 140 158 186
CINCHES 0.83 0.83 1.15 1.28 1.53 1.72 1.88 2.11 2.75 3.11 3.66mm 21 21 29 33 39 44 48 54 70 80 93
DINCHES 1.38 1.38 1.50 1.61 2.00 2.17 2.72 2.87 3.66 4.02 4.33mm 35 35 38 41 51 55 69 73 93 102 110
EINCHES 3.31 3.31 3.31 3.31 4.65 4.65 5.28 5.28 7.87 7.87 7.87mm 84 84 84 84 118 118 134 134 200 200 200
F THREADSIZE
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT 1" NPT 1-1/4"
NPT1-1/2" NPT 2" NPT 2-2/1"
NPT 3" NPT 4" NPT
Cv 9 9 12 18 40 72 112 161 287 448 645Note: DN (Diameter Nominal) = Metric equivalent size.
690
1380
2070
2760
3450
GNIKROW
ERUSSERPp-
si
WORKING TEMPERATURE - F
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
100
200
300
400
500
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438 93
Seat Material Rating
232
1
4 3
2
58
7 10
6
D
A
F
9
BC
ER
LIM
WE
EK
UA
VL
AE
VP
MO
CY
NA
004
GO
W
Rev. 16
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Standard Port (1/2”-4”) Full Port (1/4”-3/8”)400 WOG
Threaded EndsBlow-Out Proof Stem
MSS SP-110
BA-200* ¼”-4”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-11
690
1380
2070
2760
3450
p-ERUSSERP
GNIKROW
is
WORKING TEMPERATURE - F
100
200
300
400
500
0 50 150 200 250 300 350 400 450100
aPK-ERUSSERP
GNIKRO
W
Body / Seat Material Rating
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
10WORKING TEMPERATURE - C
66 121 149 177 20438 93 232
BC
1
43
2
5
8
7 10
6
D
E
A
F
9
R
PM
OC
EVL
AVE
EK
UA
WLI
MY
NA
004
GO
W
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass,Forged B2832 Tailpiece Brass,Forged B283
3 BallBrass,CP B283Brass CP, Cast B584
4 Seat PTFE5 Stem Brass B1246 Thrust Washer PTFE7 Gland Nut Brass B168 Gland Packing PTFE9 Handle Steel w/Zinc Plating Commercial
10 Handle Nut Brass B16
DIMENSIONS
UNITS3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
A (DIA)
INCHES 0.31 0.39 0.59 0.76 0.98 1.26 1.50 2.00 2.52mm 8 10 15 19 25 32 38 51 64
BINCHES 1.75 2.19 2.83 3.44 3.85 4.43 5.23 5.94 6.97mm 45 56 72 87 98 113 133 151 177
CINCHES 0.88 1.14 1.42 1.72 1.93 2.23 2.62 2.97 3.49mm 22 29 36 44 49 57 67 75 89
DINCHES 1.38 1.50 1.61 2.00 2.17 2.72 2.87 3.66 4.02mm 35 38 41 51 55 69 73 93 102
EINCHES 3.31 3.31 3.31 4.65 4.65 5.28 5.28 7.87 7.87mm 84 84 84 118 118 134 134 200 200
F TUBESIZEØ 0.51 0.63 0.88 1.13 1.38 1.63 2.13 2.63 3.13
Cv 9 12 18 40 72 112 161 287 448Note: DN (Diameter Nominal) = Metric equivalent size.
Rev. 15
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Standard Port400 WOG
Solder EndsBlow-Out Proof Stem
MSS SP-110
BA-250* ⅜”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-12
PRESSURE and TEMPERATURE CHART
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438 93 232
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.
Saturated Steam Limit
(1) Milwaukee Valve Company recommends the use
(2) Ball and stem are stainless for 300S.
of Stainless Steel ball and stem for steamapplications. Please consult factory for moreinformation.
11
12
1413
L
1 2
3
B
10
H7
8
5
4
69
W
A*
W
A
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B5842 End Cap Bronze B584
3 StemBrass B16316 Stainless Steel (2) A276
4 Packing Nut Brass B165 Packing PTFE6 Thrust Washer RPTFE, 25% Glass Filled
7 BallCP Brass B16316 Stainless Steel (2) A276
8 Seat RPTFE, 15% Glass Filled9 O-Ring Viton Commercial
10 Handle Steel w/Zinc Plating Commercial11 Handle Grip Vinyl Commercial12 Handle Nut Steel w/Zinc Plating Commercial13 Bolt Steel w/Zinc Plating Commercial14 Nut Steel w/Zinc Plating Commercial
(1) Milwaukee Valve Company recommends the use of Stainless Steel ball and stem for steam applications. Please consult factory for more information. (2) Ball and stem are stainless for 300S
DIMENSIONS
UNITS1/4”DN6
3/8”DN10
1/2”DN15
3/4”DN20
1”D25
1-1/4”D32
1-1/2”D40
2”D50
2-1/2”DN 65
3” *DN 80
AINCHES 0.50 0.50 0.50 0.75 1 1.25 1.50 2.00 2.50 2.50mm 13 13 13 19 25 32 38 51 64 64
BINCHES 3.03 3.03 3.03 3.65 3.82 4.86 5.06 6.00 7.00 7.00mm 77 77 77 90 97 123 129 152 178 178
HINCHES 1.65 1.65 1.65 2.24 2.65 2.86 3.03 3.26 4.09 4.09mm 42 42 42 57 67 73 77 83 104 104
LINCHES 4.03 4.03 4.06 4.58 6.30 6.32 7.20 7.20 8.00 8.00mm 102 102 103 116 160 161 183 183 203 203
WINCHES 1.95 1.95 1.95 2.19 2.48 3.00 3.13 3.78 6.25 6.25mm 50 50 50 56 63 76 80 96 159 159
F THREADSIZE
1/4” NPT
3/8”NPT
1/2”NPT
3/4”NPT 1” NPT 1-1/4”
NPT1-1/2”NPT 2” NPT 2-1/2”
NPT 3” NPT
Cv 7 7 17 31 60 110 185 360 390 390Note: DN (Diameter Nominal) = Metric equivalent size.* 3” is Standard Port.
Rev. 12
*Not intended for use in potable water.
Bronze Ball ValveThree Piece
Full Port600 WOG/150 SWP (1)
Threaded EndsBlow-Out Proof Stem
MSS SP-110
BA-300/300S* ¼”-3”
1/4”-2” Sizes 2-1/2”-3” Sizes
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-13
W
A*
11
12
1413
L
1 2
3
B
10
H7
8
5
4
69
With Press Ends
MATERIAL LISTITEM PART MATERIAL ASTM SPEC
1 Body Bronze B5842 End Cap Bronze B584
3 StemBrass B16316 Stainless Steel (2) A276
4 Packing Nut Brass B165 Packing PTFE6 Thrust Washer RPTFE, 25% Glass Filled
7 BallCP Brass B16316 Stainless Steel (1) A276
8 Seat RPTFE, 15% Glass Filled9 O’Ring Viton Commercial10 Handle Steel w/Zinc Plating Commercial11 Hand Grip Vinyl Commercial12 Handle Nut Steel w/Zinc Plating Commercial13 Bolt Steel w/Zinc Plating Commercial14 Nut Steel w/Zinc Plating Commercial
15 Press Adapters Brass Fitting w/EPDM O-Ring B283
(1) Ball & Stem are stainless steel for BA300S P2
Press End Adapter (4151 SERIES)
15
Rev. 4
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)INCHES 0.50 0.75 1.00 1.25 1.50 2.00mm 13 19 25 32 38 51
STD INSERTION
DEPTH
INCHES 0.87 0.98 0.98 1.02 1.42 1.58
mm 22 25 25 26 36 40
BINCHES 3.03 3.65 3.82 4.86 5.06 6.00mm 77 90 97 123 129 152
HINCHES 1.65 2.24 2.65 2.86 3.03 3.26mm 42 57 67 73 77 83
LINCHES 4.06 4.58 6.30 6.32 7.20 7.20mm 103 116 160 161 183 183
WINCHES 1.95 2.19 2.48 3.00 3.13 3.78mm 50 56 63 76 80 96
F THREAD SIZE
1/2" 3/4" 1" 1 1/4" 1 1/2" 2"
NPT NPT NPT NPT NPT NPTCv INCHES 17 31 60 110 185 360
Note: DN (Diameter Nominal) = Metric equivalent size. +Non-Shock
*Not intended for use in potable water.
Bronze Ball ValveThree Piece
Full Port200 psig @ 250°F†Press x Press Ends
Press x Threaded Ends Available (Consult Factory)Blow-Out Proof Stem
Conforms to MSS SP-110
BA-300/300S* P2 ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-14
L2
A*
1213
W
R
MILW
AU
KE
EVA
LVE
BA
-300
OPEN
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze ASTM B61/B62
2 End Cap Cast Bronze ASTM B61/B62
3 Stem 316 Stainless Steel ASTM A2764 Packing PTFE5 Packing Nut Brass ASTM B16
6 Thrust WasherRPTFE 25% Glass Reinforced
7 Ball Stainless Steel ASTM A276
8 SeatRPTFE 15% Glass Reinforced
9 O-ring Viton® Commercial10 Handle Stainless Steel Commercial11 Handle Grip Vinyl12 Handle Nut Stainless Steel Commercial13 Bolt Stainless Steel Type 304 ASTM F59314 Nut Stainless Steel Type 304 ASTM F594
(1) Milwaukee Valve Company recommends the use of Stainless Steel ball and stem for steam applications. Please consult factory for more information. (2) Ball and stem are stainless for 300SBS
** Pressure temperature charts contain valve seat and body ratings for standard valves using normal solder installation techniques. Solder end valves are de-rated by the lim-itations of the joint as specified in ASME 16.18. Brazing installations can have the same effect on the valve rating. Consult ASME 16.18 and the American Welding Society for the actual joint ratings of the material being used for the specific application.
DIMENSIONS
UNITS1/4”DN6
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
AINCHES 0.50 0.50 0.50 0.75 1.00 1.25 1.50 2.00mm 13 13 13 19 25 32 38 51
BINCHES 3.03 3.03 3.03 3.56 3.82 4.86 5.06 6.00mm 77 77 77 90 97 123 129 152
HINCHES 1.65 1.65 1.65 2.24 2.65 2.86 3.03 3.26mm 42 42 42 57 67 73 77 83
LINCHES 4.03 4.03 4.06 4.58 6.30 6.32 7.20 7.20mm 102 102 103 116 160 161 183 183
WINCHES 1.95 1.95 1.95 2.19 2.48 3.00 3.13 3.78mm 50 50 50 56 63 76 80 96
F THREADSIZE 1/4” NPT 3/8” NPT 1/2” NPT 3/4” NPT 1” NPT 1 1/4”
NPT1 1/2” NPT 2” NPT
Cv 7 7 17 31 60 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size.
Rev. 9
*Not intended for use in potable water.
Bronze Ball Valve***Three Piece
Full Port600 WOG/150 SWP (1)
Silbraze EndsBlow-Out Proof Stem
MSS SP-110
BA-300SB/300SBS** ¾”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-15
MATERIALS LISTITEM PART MODEL/SIZE MATERIALS ASTM SPEC.
1 Body 350 & 350S Cast Bronze B5842 Tailpiece 350 & 350S Bronze B584
3 Ball350 Chrome Plated Brass B16350S 316 Stainless Steel (1) A276
4 Packing350 Brass B16350S 316 Stainless Steel (1) A276
5 O-Ring 350 & 350S Viton MIL-R-832486 Seat 350 & 350S 15% Glass RPTFE7 Thrust, Washer 350 & 350S 25% Glass RPTFE
8Packing, Male 2-1/2”-3” PTFE (2 1/2" - 3")Packing 3/8”-2” PTFE ( 3/8" - 2")
9 Packing, “V” 350 & 350S PTFE 10 Packing, Female 350 & 350S PTFE11 Packing Follower 350 & 350S Brass B1612 Hex Jam Nut 350 & 350S Stainless Steel Commercial13 Nut Locker 350 & 350S S.S. Type 301/30214 Washer, Internal Tooth 350 & 350S Stainless Steel Commercial15 Belleville, Washer 350 & 350S S.S. 17-7 PH Commercial16 Hex Head Cap Screw 350 & 350S SAE, Grade 8 Commerical17 Socket Head Cap Screw 2-1/2”-3” Commercial Carbon Steel Zinc Plated18 Handle Assy 350 & 350S - -19 Gland Nut 3/8”-2” Brass B1620 Hex Nut 3/8”-2” Commercial SAE 5140
(1) Ball and stem are stainless for 350S
**
505
270
485
395
210
325
175
0
100
200
300
400
500
600
700
0 50 100 150 200 250
PRESSURE
psig
TEMPERATURE, Degrees FSolder Joint And Service As Per ANSI B16.18
PRESSURE VS TEMP. (based on 95/5 solder)
3/8 thru 1"
1 1/4 thru 2"
2 1/2 thru 4"
600
4” Only
BA-350/350S 12"/ - "
BRONZE-PIECE, FULL-PORT
600 WOGSOLDERED ENDSBLOW-OUT PROOF STEM
BALL VALVETHREE
MSS SP-110
(1) Ball and stem are stainless for 350S
PRESSURE and TEMPERATURE CHARTSeat Material RatingSolder Joints per ANSI B16.18
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.
3
DIMENSIONS
UNITS3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
AINCHES 2.68 3.02 3.56 3.81 4.66 5.00 5.70 7.01 7.01mm 68 77 90 97 118 127 145 178 178
BINCHES 0.44 0.51 0.76 0.92 0.98 1.10 1.35 1.48 1.67mm 11 13 19 23 25 28 34 38 42
CINCHES 1.85 1.85 2.20 2.65 2.79 2.97 3.47 5.44 5.44mm 47 47 56 67 71 75 88 138 138
DINCHES 0.45 0.50 0.75 1.00 1.25 1.50 2.00 2.50 2.50mm 11 13 19 25 32 38 51 64 64
EINCHES 1.32 1.32 2.13 2.41 2.94 3.13 3.86 5.74 5.74mm 34 34 54 61 75 80 98 146 146
FINCHES 3.80 3.80 4.55 6.32 6.32 6.32 7.20 8.10 8.10mm 96 96 116 160 160 160 183 206 206
GINCHES 1.92 1.92 2.13 2.41 2.94 3.13 3.86 6.31 6.31mm 49 49 54 61 75 80 98 160 160
Cv 7 17 31 60 110 185 360 390 390*3” is standard Port. **2-1/2” & 3” Only.
Rev. 13
*Not intended for use in potable water.
Bronze Ball ValveThree Piece
Full Port600 WOG
Solder EndsBlow-Out Proof Stem
MSS SP-110
BA-350/350S* ⅜”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-16
MATERIALS LISTITEM PART MODEL/SIZE MATERIALS ASTM SPEC.
1 Body BA350 & 350S Bronze B5842 Sil. Braised Stub, Male BA350 & 350S Bronze, Copper Tube
3 BallBA350 Chrome Plated Brass B16BA350S 316 Stainless Steel (1) A276
4 StemBA350 Brass B16BA350 & 350S 316 Stainless Steel (1) A276
5 Seat BA350 & 350S 15% Glass RPTFE6 O-Ring BA350 & 350S Viton MIL-R-832487 Washer, Thrust BA350 & 350S 25% Glass RPTFE
8Packing BA350 & 350S PTFE Packing, Male BA350 & 350S PTFE
9 Packing, “V” BA350 & 350S PTFE 10 Packing, Female BA350 & 350S PTFE11 Packing Follower BA350 & 350S Brass B1612 Washer, Belleville BA350 & 350S 17-7 PH S.S. Commercial13 Nut Locker BA350 & 350S S.S. 301 Commercial14 Handle Assy 350 & 350S -15 Hex Head Cap Screw BA350 & 350S SAE, Grade 8 Commerical16 Nut, Jam BA350 & 350S Steel, Zinc Plating Commercial17 Washer, Internal Tooth BA350 & 350S Stainless Steel Commercial18 Socket Head Cap Screw 2-1/2”-3” Commercial Carbon Steel Zinc Plated19 Gland Nut 1/2”-2” Brass B1620 Hex Nut 1/2”-2” Commercial SAE 5140
(1) Ball and stem are stainless for 350STE
DIMENSIONSUNITS 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3”
AINCHES 13.84 13.92 13.95 14.82 15.10 15.50 19.01 19.01mm 352 354 354 376 384 394 483 483
BINCHES 3.02 3.56 3.81 4.66 5.00 5.70 7.01 7.01mm 77 90 97 118 127 145 178 178
CINCHES 1.85 2.20 2.65 2.80 2.97 3.47 5.39 5.39mm 47 56 67 71 75 88 137 137
ØDINCHES 0.50 0.75 1.00 1.25 1.50 2.00 2.44 2.91mm 13 19 25 32 38 51 62 74
EINCHES 1.32 2.13 2.41 2.94 3.13 3.86 5.74 5.74mm 34 54 61 75 80 98 146 146
FINCHES 1.92 2.13 2.41 2.94 3.13 3.86 6.31 6.31mm 49 54 61 75 80 98 160 160
GINCHES 3.80 4.56 6.32 6.32 6.32 7.20 8.10 8.10mm 97 116 161 161 161 183 206 206
Cv 17 31 60 110 185 360 390 390Note: DN (Diameter Nominal) = Metric equivalent size. * Designed for soft solder or brazed installation without disassembly.
** Pressure temperature charts contain valve seat (1) Ball and stem are stainless for 350STE and body ratings for standard valves. Solder end valves are de-rated by the limitations of the joint as specified in ASME 16.18. Brazing installations can be likewise derated. Consult ASME 16.18 and the American Weld-ing Society for the actual joint ratings of the material being used for the specific application. Pressure and Temperature ratings may be further derated in accordance with the pressure rating associated with the type of copper tube used for the stub end. Call the factory for accurate application data.
Available Options• Male Tube Ends - Type “K” (Standard)• Female Tube Ends - Type “L” (-F)• Cleaned For Oxygen Service In Accordance
With NFPA 99C (-OC)• Stainless-Steel Ball And Stem (-S)• Stainless-Steel Locking Lever (-LD)• Oval Handle (-OH)• Oval Locking Handle (-LO)• Stem Extension (-XH)• Stainless-Steel Lever Handle (-SH)• Gauge Ports
Rev. 8
*Not intended for use in potable water.
Bronze Ball ValveThree Piece
Full Port600 WOG
Extended Tube EndsInline Repairable
Blow-Out Proof StemMSS SP-110
BA-350TE/350STE* ½”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-17
Available Options• Male Tube Ends - Type “K” (Standard)• Female Tube Ends - Type “L” (-F)• Cleaned For Oxygen Service In Accordance
With NFPA 99C (-OC)• Stainless-Steel Ball And Stem (-S)• Stainless-Steel Locking Lever (-LD)• Oval Handle (-OH)• Oval Locking Handle (-LO)• Stem Extension (-XH)• Stainless-Steel Lever Handle (-SH)
BA-350TE-G/350STE-GBRONZE
-PIECE, FULL-PORT600 WOG / 150 SWPEXTENDED TUBE ENDS WITH 1/8” NPT GAUGE PORTIN-LINE REPAIRABLEBLOW-OUT PROOF STEM
BALL VALVETHREE
BA350ste_rev2.CDR
MSS SP-110
* Designed for soft solder or brazed installationwithout disassembly.
Pressure temperature charts contain valve seatand body ratings for standard valves. Solderend valves are de-rated by the limitations of thejoint as specified in ASME 16.18. Brazinginstallations can be likewise derated. ConsultASME 16.18 and the American Welding Societyfor the actual joint ratings of the material beingused for the specific application.Pressure and Temperature ratings may befurther derated in accordance with the pressurerating associated with the type of copper tubeUsed for the stub end. Call the factory foraccurate application data.
1/2”-2”
Available Options.* Male Tube Ends-Type “K” (Standard)* Female Tube Ends-Type “L” (-F)* Cleaned For Oxygen Service
Accordance With NFPA 99 (-OC)* Stainless Steel Ball And Stem (-S)
* Oval Handle (-OH) * Oval Locking Handle (-LO)* Stem Extension (-XH)* Stainless Steel Lever Handle (-SH)
“W”
“ F”
MILWAUKEE VALVE
The information presented on this sheet is correct at the time of publication. Milwaukee Valve Company reserves the right to changedesign, and/or material specifications without notice. For the most current information access www.milwaukeevalve.com
“B”
“D”
“E”
“A”
“C”
1/2" 3/4" 1" 1-1/4" 1-1/2" 2"DN15 DN20 DN25 DN32 DN40 DN50
mm 533 533 533 533 533 533
mm 175 178 178 188 193 196C INCH 6.4 6.1 5.9 5.5 5.4 5
mm 163 155 150 140 137 127D INCH 3.8 4.8 4.8 6.5 7.4 7.4
mm 97 122 122 165 188 188E INCH 1.6 2.3 2.4 2.8 3.1 3.6
mm 41 58 61 71 79 91ØF INCH 0.5 0.75 1 1.25 1.5 2
mm 13 19 25 32 38 51
mm 48 56 64 76 76 102
Cv 17 31 60 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size
NCH 6.9 7 7 7.4 7.6 7.7
A INCH 21 21 21 21 21 21
* S tainless S teel Locking Lever (-LD)
W INCH 1.9 2.2 2. 5 3 3 4
UNITS
DIMENSIONS
Rev. 3
BA-350TE-G/350STE-GBRONZE
-PIECE, FULL-PORT600 WOG / 150 SWPEXTENDED TUBE ENDS WITH 1/8” NPT GAUGE PORTIN-LINE REPAIRABLEBLOW-OUT PROOF STEM
BALL VALVETHREE
BA350ste_rev2.CDR
MSS SP-110
* Designed for soft solder or brazed installationwithout disassembly.
Pressure temperature charts contain valve seatand body ratings for standard valves. Solderend valves are de-rated by the limitations of thejoint as specified in ASME 16.18. Brazinginstallations can be likewise derated. ConsultASME 16.18 and the American Welding Societyfor the actual joint ratings of the material beingused for the specific application.Pressure and Temperature ratings may befurther derated in accordance with the pressurerating associated with the type of copper tubeUsed for the stub end. Call the factory foraccurate application data.
1/2”-2”
Available Options.* Male Tube Ends-Type “K” (Standard)* Female Tube Ends-Type “L” (-F)* Cleaned For Oxygen Service
Accordance With NFPA 99 (-OC)* Stainless Steel Ball And Stem (-S)
* Oval Handle (-OH) * Oval Locking Handle (-LO)* Stem Extension (-XH)* Stainless Steel Lever Handle (-SH)
“W”
“ F”
MILWAUKEE VALVE
The information presented on this sheet is correct at the time of publication. Milwaukee Valve Company reserves the right to changedesign, and/or material specifications without notice. For the most current information access www.milwaukeevalve.com
“B”
“D”
“E”
“A”
“C”
1/2" 3/4" 1" 1-1/4" 1-1/2" 2"DN15 DN20 DN25 DN32 DN40 DN50
mm 533 533 533 533 533 533
mm 175 178 178 188 193 196C INCH 6.4 6.1 5.9 5.5 5.4 5
mm 163 155 150 140 137 127D INCH 3.8 4.8 4.8 6.5 7.4 7.4
mm 97 122 122 165 188 188E INCH 1.6 2.3 2.4 2.8 3.1 3.6
mm 41 58 61 71 79 91ØF INCH 0.5 0.75 1 1.25 1.5 2
mm 13 19 25 32 38 51
mm 48 56 64 76 76 102
Cv 17 31 60 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size
NCH 6.9 7 7 7.4 7.6 7.7
A INCH 21 21 21 21 21 21
* S tainless S teel Locking Lever (-LD)
W INCH 1.9 2.2 2. 5 3 3 4
UNITS
DIMENSIONS
Rev. 3
** Pressure temperature charts contain valve seat (1) Ball and stem are stainless for 350STE and body ratings for standard valves. Solder end valves are de-rated by the limitations of the joint as specified in ASME 16.18. Brazing installations can be likewise derated. Consult ASME 16.18 and the American Weld-ing Society for the actual joint ratings of the material being used for the specific application. Pressure and Temperature ratings may be further derated in accordance with the pressure rating associated with the type of copper tube used for the stub end. Call the factory for accurate application data.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
AINCHES 21.00 21.00 21.00 21.00 21.00 21.00mm 533 533 533 533 533 533
BINCHES 6.90 7.00 7.00 7.40 7.60 7.70mm 175 178 178 188 193 196
CINCHES 6.40 6.10 5.90 5.50 5.40 5.00mm 163 155 150 140 137 127
DINCHES 3.80 4.80 4.80 6.50 7.40 7.40mm 97 122 122 165 188 188
EINCHES 1.60 2.30 2.40 2.80 3.10 3.60mm 41 58 61 71 79 91
FINCHES 0.50 0.75 1.00 1.25 1.50 2.00mm 13 19 25 32 38 51
GINCHES 1.90 2.20 2.50 3.00 3.00 4.00mm 48 56 64 76 76 102
Cv 17 31 60 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size.
Rev. 5
*Not intended for use in potable water.
Bronze Ball ValveThree Piece
Full Port600 WOG
Extended Tube Ends with 1/8” NPT Gauge PortInline Repairable
Blow-Out Proof StemMSS SP-110
BA-350TE-G/350STE-G* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-18
690
1380
2070
2760
4140
3450
4830
WOR
KING
PRES
SURE
sip-
100
200
300
400
600
500
700
Saturated Steam
WORKING TEMPERATURE - F0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
AD
E
2
34
567
8
910
11
BC
1
F
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
DIMENSIONSUNITS
1/4”DN10
3/8”DN10
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.38 0.38 0.50 0.76 1.06 1.31 1.56 2.00mm 10 10 13 19 27 33 40 51
BINCHES 1.86 1.86 2.19 2.59 3.32 3.77 4.28 5.10mm 46 46 54 66 84 96 109 130
CINCHES 1.00 1.00 1.10 1.30 1.59 1.81 2.06 2.37mm 25 25 27 33 40 46 52 60
DINCHES 1.78 1.81 1.91 2.32 2.68 2.82 3.00 3.36mm 44 44 47 59 68 72 76 85
EINCHES 3.82 3.82 3.82 4.55 6.33 6.33 6.33 7.19mm 94 94 94 116 161 161 161 183
F THREADSIZE 1/4" NPT 3/8"NPT 1/2" NPT 3/4" NPT 1"NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 7 7 13 30 61 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size.
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16316 Stainless Steel (BA-400S) A276
4 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (BA-400S) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial
(1) For steam service please specify see BA400S3.
Rev. 16
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Full Port 600 WOG/150 SWP (1)
Threaded EndsBlow-Out Proof Stem
MSS SP-110
BA-400/400S* ¼”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-19
/ 2BRONZE BALL VALVETWO-PIECE, FULL-PORT200 PSIG @ 250°FPRESS ENDSBLOW-OUT PROOF STEM
AD
E
2
34
567
8
910
11
DIMENSIONS
BC
BA-400 400S* P2 12 -" "
1
F
MSS SP-110
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
(1) For steam service specify see BA400S3
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
BRONZE BALL VALVETWO-PIECE, FULL-PORT600 PSIG WOG / 150 PSIG SWP (1)THREADED ENDS
AD
E
2
34
567
8
910
11
DIMENSIONS
BC
BA-400 400S 14 -"/ 2 "
1
F
FED. SPEC. WW-V-35C, II, BZ, 3MSS SP-110
O P E N600W
OG
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
(1) Milwaukee Valve Company recommends the use of
(2) Ball and stem are stainless for 400S.(3) For steam service, specify stainless trim and multi-fil
seats, maximum stem pressure 150.
stainless steel ball and stem for steam applications.Please consult factory for more information.
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERP- p
is
WORKING TEMPERATURE - F
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438
Seat Material Rating
93
SaturatedSteam
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
B1
MATERIAL LISTITEM PART MATERIAL ASTM SPEC
1 Body Cast Bronze B5842 Tailpiece Brass B283
Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16316 Stainless Steel (BA-400S) A276
4 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (BA-400S) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl11 Handle Nut Steel w/Zinc Plating Commercial12 Press Adapters Brass Fitting w/EPDM O-Ring B283
(1) Ball & Stem are stainless steel for BA-400S P2
Press End Adapter (4151 Series)
12
Rev. 6
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Press Ends
Blow-Out Proof StemMSS SP-110
BA-400/400S* P2 ½”-2”
DIMENSIONSUNITS
1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A (DIA)INCHES 0.50 0.76 1.06 1.31 1.56 2.00mm 13 19 27 33 40 51
STD INSERTION
DEPTH
INCHES 0.87 0.98 0.98 1.02 1.42 1.58
mm 22 25 25 26 36 40
BINCHES 2.19 2.59 3.32 3.77 4.28 5.10mm 54 66 84 96 109 130
B1 INCHES 5.19 6.17 7.32 7.84 8.76 11.10mm 132 157 186 199 228 282
CINCHES 1.10 1.30 1.59 1.81 2.06 2.37mm 27 33 40 46 52 60
DINCHES 1.91 2.32 2.68 2.82 3.00 3.36mm 47 59 68 72 76 85
EINCHES 3.82 4.55 6.33 6.33 6.33 7.19mm 94 116 161 161 161 183
F THREAD SIZE 1/2" NPT 3/4" NPT 1"NPT 1-1/4" NPT 1-1/2" NPT 2" NPTCv 13 30 61 110 185 360
Note: DN (Diameter Nominal) = Metric equivalent size. †Non-Shock
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-20
BRONZE BALL VALVETWO-PIECE, FULL-PORT600 PSIG WOG /250 PSIG SWPTHREADED ENDSBLOW-OUT PROOF STEM
AD
E
2
34
567
8
910
11
DIMENSIONS
BC
BA-400S3 1 -"/ 2 "
1
F
MSS SP-110
O P E N
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
2
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 Ball 316 Stainless Steel A2764 Seat Multi-Fill PTFE
5 StemBrass B16316 Stainless Steel A276
6 Thrust Washer Multi-Fill PTFE7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial
10 Hand Grip Vinyl Commercial11 Handle Nut Steel w/Zinc Plating Commercial
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DM25
1-1/4”DM32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.50 0.76 1.06 1.31 1.56 2.00mm 13 19 27 33 40 51
BINCHES 2.19 2.59 3.32 3.77 4.28 5.10mm 54 66 84 96 109 130
CINCHES 1.10 1.30 1.59 1.81 2.06 2.37mm 27 33 40 46 52 60
DINCHES 1.91 2.32 2.68 2.82 3.00 3.36mm 47 59 68 72 76 85
EINCHES 3.82 4.55 6.33 6.33 6.33 7.19mm 94 116 161 161 161 183
F THREADSIZE 1/2" NPT 3/4"NPT 1"NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 13 30 61 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size.
PRESSURE/TEMPERATURE RATINGS
Steam Limit (03 Seat)
Rev. 4
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Full Port 600 W0G/250 SWP
Threaded EndsBlow-Out Proof Stem
MSS SP-110
BA-400S3* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-21
BRONZE BALL VALVETWO-PIECE, FULL-PORT600 PSIG WOGSOLDER ENDSBLOW-OUT PROOF STEM
DIMENSIONS
BA-450 38 -"/ 2 "MSS SP-110
B
A
F
D
C
E
2
910
11
1
57
34
6
8
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
(1) Ball and stem are stainless for 450S.
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Cast Bronze B584
2 TailpieceBrass B283Cast Bronze (1 1/4" & up) B584
3 BallBrass w/Hard Chrome Plating B16316 Stainless Steel (1) A276
4 Seat RPTFE, 15% Glass Filled
5 StemBrass B16316 Stainless Steel (1) A276
6 Thrust Washer RPTFE, 25% Glass Filled7 Packing PTFE8 Packing Nut Brass B169 Handle Steel w/Zinc Plating Commercial10 Hand Grip Vinyl Commercial11 Handle Nut Steel w/Zinc Plating Commercial
(1) Ball and stem are stainless for 450S.
DIMENSIONS
UNITS3/8”DN10
1/2”DN15
3/4”DN20
1”DM25
1-1/4”DM32
1-1/2”DN40
2”DN50
A (DIA)
INCHES 0.38 0.50 0.76 1.06 1.31 1.56 2.00mm 10 13 19 27 32 40 51
BINCHES 2.05 2.39 3.17 3.75 5.00 6.00 6.75mm 52 59 81 95 127 152 172
CINCHES 0.91 1.07 1.50 1.79 2.49 3.00 3.37mm 23 27 38 46 63 76 86
DINCHES 1.80 1.87 2.19 2.67 2.82 2.99 3.51mm 44 46 56 68 72 76 89
EINCHES 3.80 3.80 4.56 6.31 6.31 6.31 7.19mm 97 97 116 160 160 160 183
F TUBE SIZEØ 0.51 0.63 0.88 1.13 1.38 1.63 2.13
Cv 7 15 35 60 110 185 360Note: DN (Diameter Nominal) = Metric equivalent size.
BRONZE BALL VALVETWO-PIECE, FULL-PORT600 PSIG WOGSOLDER ENDSBLOW-OUT PROOF STEM
DIMENSIONS
BA-450 38 -"/ 2 "MSS SP-110
B
A
F
D
C
E
2
910
11
1
57
34
6
8
O P E N600W
OG
150S
WP
MILW
AU
KE
EVA
LVE
CO
MPA
NY,IN
CR
(1) Ball and stem are stainless for 450S.
VALVES RATED FOR VACUUM SERVICE TO 29 INCHES Hg.PRESSURE - TEMPERATURE DATA
505
270
485
395
210
0
100
200
300
400
500
600
700
0 50 100 150 200 250
PRESSURE
psig
PRESSURE VS TEMP. (based on 95/5 solder)
3/8 thru 1"
1 1/4 thru 2"
600
TEMPERATURE, Degrees FSolder Joint And Service As Per ANSI B16.18
Rev. 12
*Not intended for use in potable water.
Bronze Ball ValveTwo Piece
Full Port 600 WOG
Solder EndsBlow-Out Proof Stem
MSS SP-110
BA-450/450S* ⅜”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-22
BRASS BALL VALVE***
967
4
10
3
5
2
1
8 11
D
E
A
F
"BA-475B" 14 -"/ 4 "
RC US
UL 842UL 125ANSI Z 21.15a CGA 9.1a
ASME B16.44
R
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERPp-
si
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE CHART
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438 93
CB
Seat Material Rating
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 Ball CP Brass 3/8” - 1-1/4”CP Brass, Cast 1-1/2 - 4” B584
4 Ball Seal PTFE Commercial5 Stem Brass B1246 O-Ring Buna-N D20067 ThrustWasher PTFE Commercial8 Gland Nut Brass B169 Packing PTFE Commercial
10 Handle Zinc Plated Steel Commercial11 Handle Nut Zinc Plated Steel Commercial
DIMENSIONS
C US600 WOG (1/4”-3”) 400 WOG (4”)TWO-PIECE, FULL-PORT MSS-SP110
ASME A112.4.14
1/4” through 2” Only
Also Available BA-475B-LL (Locks Only In Closed Position)
THREADED ENDSBLOW-OUT PROOF STEM
*
*
B283
Not Suitable For Ammonia.Not intended for use in potable water.4” Valve Only
**
**
***
APPROVED1140
****12 Body Seal PTFE Commercial
****
4” Only
BRASS BALL VALVE***
967
4
10
3
5
2
1
8 11
D
E
A
F
"BA-475B" 14 -"/ 4 "
RC US
UL 842UL 125ANSI Z 21.15a CGA 9.1a
ASME B16.44
R
690
1380
2070
2760
4140
3450
4830
GNIKROW
ERUSSERPp-
si
WORKING TEMPERATURE - F
PRESSURE - TEMPERATURE CHART
100
200
300
400
600
500
700
0 50 150 200 250 300 350 400 450100
GNIKRO
WERUSSERP
-aPK
10WORKING TEMPERATURE - C
66 121 149 177 20438 93
CB
Seat Material Rating
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 Ball CP Brass 3/8” - 1-1/4”CP Brass, Cast 1-1/2 - 4” B584
4 Ball Seal PTFE Commercial5 Stem Brass B1246 O-Ring Buna-N D20067 ThrustWasher PTFE Commercial8 Gland Nut Brass B169 Packing PTFE Commercial
10 Handle Zinc Plated Steel Commercial11 Handle Nut Zinc Plated Steel Commercial
DIMENSIONS
C US600 WOG (1/4”-3”) 400 WOG (4”)TWO-PIECE, FULL-PORT MSS-SP110
ASME A112.4.14
1/4” through 2” Only
Also Available BA-475B-LL (Locks Only In Closed Position)
THREADED ENDSBLOW-OUT PROOF STEM
*
*
B283
Not Suitable For Ammonia.Not intended for use in potable water.4” Valve Only
**
**
***
APPROVED1140
****12 Body Seal PTFE Commercial
****
4” Only
DIMENSIONSUNITS 1/4” 3/8” 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4”
A (DIA)INCHES 0.39 0.39 0.51 0.76 1.00 1.26 1.50 2.00 2.48 2.95 3.94mm 10 10 13 19 25 32 38 51 63 75 100
BINCHES 1.87 1.87 2.25 2.62 3.06 3.50 3.75 4.38 5.16 6.00 8.20mm 47 47 57 67 78 89 95 111 131 152 208
CINCHES 0.95 0.95 1.12 1.31 1.91 2.21 1.87 2.19 2.58 3.00 4.11mm 24 24 28 33 49 56 47 56 66 76 104
DINCHES 1.42 1.42 1.46 1.93 2.10 2.33 2.52 2.96 3.94 4.37 5.93mm 36 36 37 49 53 59 64 75 100 111 151
EINCHES 3.14 3.14 3.14 4.35 4.35 5.00 5.00 6.90 7.87 7.87 9.65mm 80 80 80 110 110 127 127 175 200 200 245
F THREAD SIZE
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT 1" NPT 1-1/4"
NPT1-1/2" NPT 2" NPT 2-2/1"
NPT 3" NPT 4" NPT
Cv 12 12 18 40 72 112 161 287 307 323 584
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 BallCP Brass (3/8" - 1 1/4") B283CP Brass, Cast (1 1/2" - 4") B584
4 Ball Seal PTFE Commercial5 Stem Brass B1246 O-Ring Buna-N D20067 Thrust Washer PTFE Commercial8 Gland Nut Brass B169 Packing PTFE Commercial10 Handle Zinc Plated Steel Commercial11 Hand Grip Zinc Plated Steel Commercial
****12 Body Seal PTFE Commercial
Rev. 32
*Not intended for use in potable water.
*Also Available BA-475B-LL (Locks only in closed position)** Not Suitable For Ammonia Service***Not intended for use in potable water.****4” Valve Only
Brass Ball ValveTwo Piece
Full Port600 WOG (1/4”-3”) 400 WOG (4”)
Threaded EndsBlow-Out Proof Stem
MSS SP-110, ASME A112.4.14
“BA-475B”* ¼”-4”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-23
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 BallCP Brass (1/2" - 1 1/4") B283CP Brass, Cast (1 1/2" - 4") B584
4 Ball Seal PTFE Commercial5 Stem Brass B1246 O-Ring Buna-N D20067 Thrust Washer PTFE Commercial8 Gland Nut Brass B169 Packing PTFE Commercial10 Handle Zinc Plated Steel Commercial11 Hand Grip Zinc Plated Steel Commercial**12 Body Seal PTFE Commercial
DIMENSIONSUNITS 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4”
AINCHES 0.50 0.76 1.00 1.26 1.50 2.00 2.48 2.95 3.94mm 13 19 25 32 38 51 63 75 100
BINCHES 2.28 3.10 3.56 4.13 4.64 5.75 7.25 8.25 10.33mm 58 79 90 105 118 146 131 152 262
CINCHES 1.14 1.55 1.78 2.06 2.32 2.87 3.62 4.12 5.17mm 29 39 45 52 59 73 92 105 131
DINCHES 1.46 1.93 2.10 2.33 2.52 2.96 3.94 4.37 5.96mm 37 49 53 59 64 75 100 111 151
EINCHES 3.14 4.35 4.53 5.00 5.00 6.90 7.87 7.87 9.65mm 80 110 110 127 127 175 200 200 245
F TUBE SIZE 0.63 0.88 1.13 1.38 1.63 2.13 2.63 3.13 4.13
Cv 18 40 72 112 161 287 307 323 584
"BA-485B" 1/2" - 4"BRASS BALL VALVE MSS SP-110
ASME A112.4.14
SOLDERED ENDSBLOW-OUT PROOF STEM
600 PSIG WOG (1/2”-3”) 400 WOG (4”) TWO PIECE, FULL PORT
967
4
10
3
5
2
1
8 11
A
F
B
E
D
C
DIMENSIONS
PRESSURE - TEMPERATURE CHARTVACUUM SERVICE TO 29 INCHES Hg.
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 Ball CP Brass 1/2” - 1-1/4”CP Brass, Cast 1-1/2 - 4” B584
4 Ball Seal PTFE Commercial5 Stem Brass B1246 O-Ring Buna-N D20067 ThrustWasher PTFE Commercial8 Gland Nut Brass B169 Packing PTFE Commercial
10 Handle Zinc Plated Steel Commercial11 Handle Nut Zinc Plated Steel Commercial
B283
**12 Body Seal PTFE Commercial
505
270
485
395
210
325
175
0
100
200
300
400
500
600
700
0 50 100 150 200 250
PRESSURE
psig
TEMPERATURE, Degrees FSolder Joint And Service As Per ANSI B16.18
PRESSURE VS TEMP. (based on 95/5 solder)
3/8 thru 1"
1 1/4 thru 2"
2 1/2 thru 4"
600
4” Only
Rev. 26
Brass Ball ValveTwo Piece
Full Port600 WOG (1/2”-3”) 400 WOG (4”)
Solder EndsBlow-Out Proof Stem
MSS SP-110, ASME A112.4.14
“BA-485B”* ½”-4”
*Not intended for use in potable water.**4” Valve Only
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-24
E - SWT
E - THD
E - SWT
E - THD
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass, Forged B283
3 Ball Brass with Nickel chrome Plating B283
4 Ball Seal PTFE Comercial5 Stem Brass B1246 O-Ring Buna-N D20067 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial10 Handle Zinc Plated Steel Commercial11 Hand Grip Zinc Plated Steel Commercial
DIMENSIONS
UNITS3/4”DN20
1”DN25
1-1/4”DN32
A O.V.L./THD
INCHES 2.50 2.81 2.99mm 64 71 76
A O.V.L./SWT
INCHES 2.69 3.13 3.38mm 68 80 86
BINCHES 1.24 1.32 1.32mm 31 34 34
CINCHES 1.95 2.12 2.31mm 50 54 59
DINCHES 3.29 3.29 3.29mm 84 84 84
E PORT DIA.
INCHES 0.75 1.00 1.25mm 19 25 32
F FLANGE DIA.
INCHES 4.33 4.33 4.33mm 110 110 110
GINCHES 4.72 4.72 4.72mm 120 120 120
H MTG. HOLE
INCHES 0.51 0.51 0.51mm 13 13 13
JINCHES 2.67 2.67 2.67mm 68 68 68
KINCHES 0.28 0.28 0.28mm 7 7 7
LINCHES 0.14 0.14 0.14mm 4 4 4
Rev. 7
*Not intended for use in potable water.
Brass Flange Ball ValveTwo Piece • Full Port
600 WOG BA-500 Threaded Ends/ BA-550 Solder Ends
Sold In Packages of 2Kit Includes 4 Bolts & Nuts, Plus T-Handle (1)
Blow-Out Proof StemMSS SP-110, ASME A112.4.14
BA-500/BA-550* ¾”-1¼”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-25
** 2 1/2” & 3” Requires XLC installation jaws.
13 1412**
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball CP Brass Ball B2834 Ball Seat PTFE Commercial5 Stem Brass B1246 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial10 Handle Steel w/Zinc Plating Commercial11 Handle Nut Steel w/Zinc Plating Commercial12 Tube O-Ring Plastic Commercial
13** Backing Ring EPDM Commercial14** Gripping Ring Stainless Steel Commercial* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
** For Installation Instructions please see engineering section on website.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
AINCHES 0.51 0.76 0.98 1.26 1.50 2.01 2.48 2.95mm 13 19 25 32 38 51 63 75
BINCHES 3.16 3.71 4.28 5.20 6.31 7.44 11.92 14.07mm 80 94 109 132 160 189 303 357
CINCHES 1.63 1.92 2.18 2.75 3.40 3.96 5.96 7.04mm 41 49 55 70 86 101 151 179
DINCHES 1.62 2.01 2.21 2.46 2.62 3.13 3.94 4.12mm 41 51 56 63 67 80 100 111
EINCHES 3.15 4.33 4.33 5.12 5.12 6.89 7.87 7.87mm 80 110 110 130 130 175 200 200
GINCHES 1.52 1.73 2.31 3.16 3.49 4.28 8.17 9.86mm 39 44 59 80 89 109 208 250
Cv 18 40 72 112 161 287 448 645
Rev. 17
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Press Ends
Blow-Out Proof Stem
BA-480B* ½”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-26
1/2" 3/4" 1" 1-1/4" 1-1/2" 2"
DN15 DN20 DN25 DN32 DN40 DN50
INCHES 0.51 0.76 0.98 1.26 1.50 2.01
mm 13 19.3 25 32 38 51
INCHES 3.16 3.71 4.28 5.20 6.31 7.44
mm 80 94 109 132 160 189
INCHES 1.63 1.92 2.18 2.75 3.40 3.96
mm 41.4 48.8 55.4 69.9 86.4 100.5
INCHES 1.62 2.01 2.21 2.46 2.62 3.13
mm 41.1 51.1 56.3 62.5 66.5 79.6
INCHES 3.15 4.33 4.33 5.12 5.12 6.89
mm 80 110 110 130 130 175
INCHES 1.52 1.73 2.31 3.16 3.49 4.28
mm 38.5 43.8 58.6 80.3 88.5 108.7
Cv 18 40 72 112 161 287
in-lb 19 58 69 89 124 210
N.m. 2.1 6.5 7.8 10 14 24
lbs. 0.46 0.84 1.16 1.88 2.82 5.52
grams 209 381 526 853 1279 2504
BA- 480S
DIMENSIONS
G
Torque
Weight
Size
A-PORTDIA
B
C
D
E
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball 316 S.S. A2764 Ball Seat PTFE Commercial5 Stem 316 S.S. A2766 Stem O-Ring Buna-N Commercial7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial10 Handle Steel w/Zinc Plating Commercial11 Handle Nut Steel w/Zinc Plating Commercial
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
** For Installation Instructions please see engineering section on website.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
AINCHES 0.51 0.76 0.98 1.26 1.50 2.01mm 13 19 25 32 38 51
BINCHES 3.16 3.71 4.28 5.20 6.31 7.44mm 80 94 109 132 160 189
CINCHES 1.63 1.92 2.18 2.75 3.40 3.96mm 41 49 55 70 86 101
DINCHES 1.62 2.01 2.21 2.46 2.62 3.13mm 41 51 56 63 67 80
EINCHES 3.15 4.33 4.33 5.12 5.12 6.89mm 80 110 110 130 130 175
GINCHES 1.52 1.73 2.31 3.16 3.49 4.28mm 39 44 59 80 89 109
Cv 18 40 72 112 161 287
Rev. 10
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Press Ends
Blow-Out Proof Stem
BA-480S* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-27
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball CP Brass Ball B2834 Ball Seat PTFE Commercial5 Stem Brass B1246 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial10 Handle Steel w/Zinc Plating Commercial11 Handle Nut Steel w/Zinc Plating Commercial12 Tube O-Ring Plastic Commercial13 Hose Cap Polypropylene14 Cap Gasket EPDM15 Chain Brass Bead
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
AINCHES 0.51 0.76mm 13 19
BINCHES 3.06 3.50mm 78 90
CINCHES 1.41 1.66mm 36 42
DINCHES 1.62 2.01mm 41 51
EINCHES 3.15 4.33mm 80 110
F-TUBE DIA
INCHES 0.82 0.99mm 21 25
Cv 18 40NOTE: Pressure / Temperature ratings shown are for valve only. Hose side pressure and temperature limit is based on connected hose and is the users responsibility.
Do not pressurize cap.Pressure not to exceed 40 psi.
Rev. 9
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Hose Ends
Blow-Out Proof Stem
BA-480BH* ½”-¾”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-28
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball 316 S.S. A2764 Ball Seat PTFE Commercial5 Stem 316 S.S. A2766 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial10 Handle Steel w/Zinc Plating Commercial11 Handle Nut Steel w/Zinc Plating Commercial12 Tube O-Ring Plastic Commercial13 Hose Cap Polypropylene14 Cap Gasket EPDM15 Chain Brass Bead
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
A-PORT DIA
INCHES 0.51 0.76mm 13 19
BINCHES 3.06 3.50mm 78 90
CINCHES 1.41 1.66mm 36 42
DINCHES 1.62 2.01mm 41 51
EINCHES 3.15 4.33mm 80 110
F-TUBE DIA
INCHES 0.82 0.99mm 21 25
Cv 18 40NOTE: Pressure / Temperature ratings shown are for valve only. Hose side pressure and temperature limit is based on connected hose and is the users responsibility.
Do not pressurize cap.Pressure not to exceed 40 psi.
Rev. 10
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Hose Ends
Blow-Out Proof Stem
BA-480SH* ½”-¾”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-29
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball CP Brass Ball B2834 Ball Seat PTFE Commercial5 Stem Brass B1246 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating B633
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring EPDM D2000 NSF61
13 Stem Stop Plate Steel w/Zinc Plating Commercial
14 Internal Extension Tube Steel w/Zinc Plating Commercial
15 External Extension Tube Steel w/Zinc Plating Commercial
16 Upper Stem Adaptor Steel w/Zinc Plating Commercial
17 Memory Stop Steel w/Zinc Plating Commercial
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K & L per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
2-1/2”DN65
3”DN80
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.01 2.48 2.95mm 13 19 25 32 38 51 63 75
BINCHES 3.16 3.71 4.28 5.20 6.31 7.44 11.92 14.07mm 80 94 109 132 160 189 303 357
CINCHES 1.63 1.92 2.18 2.75 3.40 3.96 5.96 7.04mm 41 49 55 70 86 101 151 179
DINCHES 3.87 4.26 4.46 4.71 4.87 5.38 6.19 6.37mm 98 108 113 120 124 137 157 162
EINCHES 3.15 4.33 4.33 5.12 5.12 6.89 7.87 7.87mm 80 110 110 130 130 175 200 200
GINCHES 1.52 1.73 2.31 3.16 3.49 4.28 8.17 9.86mm 39 44 59 80 89 109 208 250
Cv 18 40 72 112 161 287 448 645
B
A
F (TYP.)
G (TYP.)
D
E
C
SECTION A-A
11 16 17 14 15
10
1226534
7
1
9
8
11
Rev. 8
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Press Ends
With Extension Stem & Memory StopBlow-Out Proof Stem
BA-481B* ½”-3”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-30
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball 316 S.S. A2764 Ball Seat PTFE Commercial5 Stem 316 S.S. A2766 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating B633
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring EPDM D2000 NSF61
13 Stem Stop Plate Steel w/Zinc Plating Commercial
14 Internal Extension Tube Steel w/Zinc Plating Commercial
15 External Extension Tube Steel w/Zinc Plating Commercial
16 Upper Stem Adaptor Steel w/Zinc Plating Commercial
17 Memory Stop Steel w/Zinc Plating Commercial
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K & L per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.01mm 13 19 25 32 38 51
BINCHES 3.16 3.71 4.28 5.20 6.31 7.44mm 80 94 109 132 160 189
CINCHES 1.63 1.92 2.18 2.75 3.40 3.96mm 41 49 55 70 86 101
DINCHES 3.87 4.26 4.46 4.71 4.87 5.38mm 98 108 113 120 124 137
EINCHES 3.15 4.33 4.33 5.12 5.12 6.89mm 80 110 110 130 130 175
GINCHES 1.52 1.73 2.31 3.16 3.49 4.28mm 39 44 59 80 89 109
Cv 18 40 72 112 161 287
B
A
F (TYP.)
G (TYP.)
D
E
C
SECTION A-A
11 16 17 14 15
10
1226534
7
1
9
8
11
Rev. 7
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†Press x Press Ends
With Extension Stem & Memory StopBlow-Out Proof Stem
BA-481S* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-31
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball CP Brass Ball B2834 Ball Seat PTFE Commercial5 Stem Brass B1246 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating Commercial
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring Plastic D2000 NSF61* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.00mm 13 19 25 32 38 51
BINCHES 2.77 3.23 3.71 4.12 4.86 6.14mm 70 82 94 105 123 156
CINCHES 1.14 1.31 1.53 1.71 1.88 2.19mm 29 33 39 43 48 56
DINCHES 1.46 1.93 2.10 2.33 2.52 2.96mm 37 49 53 59 64 75
EINCHES 3.14 4.35 4.35 5.00 5.00 6.90mm 80 110 110 127 127 175
F-TUBE DIA
INCHES 0.63 0.88 1.13 1.38 1.63 2.13mm 15 20 25 32 40 50
F1 NPT INCHES 1/2"-14 3/4"-14 1"-11.5 1-1/4"-11.5
1-1/2"-11.5 2"-11.5
GINCHES 0.83 1.00 1.00 1.02 1.42 1.57mm 21 25 25 26 36 40
Cv 18 40 72 112 161 287
Rev. 9
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†
Press x Threaded EndsBlow-Out Proof Stem
BA-490B* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-32
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball 316 S.S. A2764 Ball Seat PTFE Commercial5 Stem 316 S.S. A2766 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating Commercial
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring EPDM D2000 NSF61* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.00mm 13 19 25 32 38 51
BINCHES 2.77 3.23 3.71 4.12 4.86 6.14mm 70 82 94 105 123 156
CINCHES 1.14 1.31 1.53 1.71 1.88 2.19mm 29 33 39 43 48 56
DINCHES 1.46 1.93 2.10 2.33 2.52 2.96mm 37 49 53 59 64 75
EINCHES 3.14 4.35 4.35 5.00 5.00 6.90mm 80 110 110 127 127 175
F-TUBE DIA
INCHES 0.63 0.88 1.13 1.38 1.63 2.13mm 15 20 25 32 40 50
F1 NPT Inches 1/2"-14 3/4"-14 1"-11.5 1-1/4"-11.5
1-1/2"-11.5 2"-11.5
GINCHES 0.83 1.00 1.00 1.02 1.42 1.57mm 21 25 25 26 36 40
Cv 18 40 72 112 161 287
Rev. 5
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†
Press x Threaded EndsBlow-Out Proof Stem
BA-490S* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-33
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball CP Brass Ball B2834 Ball Seat PTFE Commercial5 Stem Brass B1246 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating B633
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring EPDM D2000 NSF61
13 Stem Stop Plate Steel w/Zinc Plating Commercial
14 Internal Extension Tube Steel w/Zinc Plating Commercial
15 External Extension Tube Steel w/Zinc Plating Commercial
16 Upper Stem Adaptor Steel w/Zinc Plating Commercial
17 Memory Stop Steel w/Zinc Plating Commercial
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.01mm 13 19 25 32 38 51
BINCHES 2.76 3.58 3.98 4.51 5.50 6.44mm 70 91 101 115 140 164
CINCHES 1.63 1.92 2.18 2.75 3.46 3.46mm 41 49 55 70 88 88
DINCHES 3.55 4.08 4.28 4.53 4.65 5.13mm 90 104 109 115 118 130
EINCHES 3.28 4.38 4.38 4.38 6.97 6.97mm 83 111 111 111 177 177
F TUBE Ø
INCHES 0.63 0.88 1.13 1.38 1.64 2.13mm 16 22 29 35 42 54
GINCHES 0.83 0.99 0.99 1.02 1.42 1.58mm 21 25 25 26 36 40
H THRD SIZE 1/2" NPT 3/4" NPT 1" NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 18 40 72 112 161 287
Rev. 5
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†
Press x Threaded EndsWith Extension Stem & Memory Stop
Blow-Out Proof Stem
BA-491B* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-34
MATERIALS LISTITEM PART MATERIALS ASTM SPEC.
1 Body Brass, Forged B2832 Tailpiece Brass,Forged B2833 Ball 316 S.S. A2764 Ball Seat PTFE Commercial5 Stem 316 S.S. A2766 Stem O-Ring Buna-N7 Thrust Washer PTFE Commercial8 Gland Nut Brass B1249 Packing PTFE Commercial
10 Handle Steel w/Zinc Plating B633
11 Handle Bolt Steel w/Zinc Plating Commercial
12 Tube O-Ring EPDM D2000 NSF61
13 Stem Stop Plate Steel w/Zinc Plating Commercial
14 Internal Extension Tube Steel w/Zinc Plating Commercial
15 External Extension Tube Steel w/Zinc Plating Commercial
16 Upper Stem Adaptor Steel w/Zinc Plating Commercial
17 Memory Stop Steel w/Zinc Plating Commercial
* Ultra Press Valves are designed and qualified for use in copper tubing systems only, Types K, L, & M per ASTM B88.
DIMENSIONS
UNITS1/2”DN15
3/4”DN20
1”DN25
1-1/4”DN32
1-1/2”DN40
2”DN50
A-PORT DIA
INCHES 0.51 0.76 0.98 1.26 1.50 2.01mm 13 19 25 32 38 51
BINCHES 2.76 3.58 3.98 4.51 5.50 6.44mm 70 91 101 115 140 164
CINCHES 1.63 1.92 2.18 2.75 3.46 3.46mm 41 49 55 70 88 88
DINCHES 3.55 4.08 4.28 4.53 4.65 5.13mm 90 104 109 115 118 130
EINCHES 3.28 4.38 4.38 4.38 6.97 6.97mm 83 111 111 111 177 177
F TUBE Ø
INCHES 0.63 0.88 1.13 1.38 1.64 2.13mm 16 22 29 35 42 54
GINCHES 0.83 0.99 0.99 1.02 1.42 1.58mm 21 25 25 26 36 40
H THRD SIZE 1/2" NPT 3/4" NPT 1" NPT 1-1/4"
NPT1-1/2" NPT 2" NPT
Cv 18 40 72 112 161 287
Rev. 5
*Not intended for use in potable water.
Brass Ball ValveTwo Piece
Full Port 200 psig @ 250°F†
Press x Threaded EndsWith Extension Stem & Memory Stop
Blow-Out Proof Stem
BA-491S* ½”-2”
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-35MILWAUKEE VALVE
The information presented on this sheet is correct at the time of publication. Milwaukee Valve reserves the right to changedesign, and/or material specifications without notice. For the Installation, Operation and Maintenance Manual (IOM) see theengineering section on our website. For the most current information access www.milwaukeevalve.com
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
PART # SIZE(S) VALVE*Small TIH-C1-940 1/4", 3/8", 1/2" BA-475 / BA-485 / BA-480B / BA-490B Series
TIH-D-940 1/4", 3/8", 1/2" BA-100 / BA-150 / BA-400 / BA-450 SeriesTIH-D3-940 1/4", 3/8", 1/2" BA-300 / BA-350 Series
A - 4.50 1" BA-100 / BA-150 Series3/4" BA-100 / BA-150 / BA-400 / BA-450 Series
TIH-F3-940 3/4" BA-300 / BA-350 SeriesB - 3.06 TIH-H1-940 3/4",1",1 1/4", 1 1/2" BA-475 / BA-485 / BA-480B / BA-490B SeriesLarge 2" BA-100 / BA-150 Series
1 1/4", 1 1/2" BA-100 / BA-150/BA-400 / BA-450 Series1" BA-400 / BA-450 Series
A - 7.00 TIH-J1-940 2" BA-475 / BA-485 / BA-480B / BA-490B SeriesTIH-J3-940 1", 1 1/4", 1 1/2" BA-300 / BA-350 SeriesTIH-K-940 2" BA-400 / BA-450 Series
B - 3.44 TIH-K3-940 2" BA-300 / BA-350 Series
TIH-F-940
TIH-J-940
QTY. DESCRIPTION MATERIAL1 HOUSING FIRE RESISTANT ABS1 SLEEVE FIRE RESISTANT ABS1 CAP POLYETHYLENE1 INSULATION INSERT POLYSTYRENE1 SHIELD PLASTIC SLEEVE1 LOCK WASHER SS1 STOP PLATE & SCREWS SS1 MEMORY STOP ASSEMBLY SS
Bill of Material
R27752
To order factory assembled to the valve use suffix TIH (Threaded Only) Milwaukee Valve will not factory install (TIH) handle on solder end valves.*Will fit our equivalent Ultrapure Low Lead Valves.
Milwaukee Valve’s insulated extension handle is designed to prevent condensation and other extraneous moisture from entering your insulated piping system, while also minimizing thermal energy loss from the system via metal extension tubes, levers, and similar parts.
Our handle design incorporates a unique memory stop feature that requires no disassembly or removal of the handle to engage and make adjustments.
Rev. 7
Rev. 8
MILWAUKEE VALVE
The information presented on this sheet is correct at the time of publication. Milwaukee Valve reserves the right to changedesign, and/or material specifications without notice. For the Installation, Operation and Maintenance Manual (IOM) see theengineering section on our website. For the most current information access www.milwaukeevalve.com
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
NEW BERLIN, WI 53151-7301MILWAUKEE VALVE CO., INC.
DWN
CHKD
APVD
MDLD
REG APVL
TITLE
SHEET
in [mm]PRIMARY / SECONDARY
UNITS
THIS PRINT IS THE PROPERTY OF MILWAUKEE VALVE COMPANY, INC. AND REPRESENTS A PROPIETARY ARTICLE IN WHICH MILWAUKEE VALVE COMPANY, INC. RETAINS ANY
AND ALL PATENTS AND OTHER RIGHTS, INCLUDING EXCLUSIVE RIGHTS OF USE AND/OR MANUFACTURE AND/OR SALE. POSSESION OF THIS PRINT DOES NOT CONVEY ANY
PERMISSION TO REPRODUCE PRINT OR MANUFACTURE THE ARTICLE OR ARTICLES SHOWN THEREIN; SUCH PERMISSION
TO BE GRANTED ONLY BY SPECIFIC AUTHORIZATION IN WRITING, SIGNED BY AN OFFICER OR OTHER AUTHORIZED
AGENT OF MILWAUKEE VALVE COMPANY INC.
THIRD ANGLE PROJECTION
SCALE: 1:1 MASS UNITS:
INTL ECN12-472
DEPARTMENTENGINEERING
NAP8/28/13
08-27-2013 NAPPC NOREF NO
SIZE
DCAGE CODE
76364
CUT SHEET
DRAWING NO
TIH-X1 OF 1
REV
A
SMALL B
A
3.56 2.75
LARGE
13 1 SPRING SS
12 1 MS PLUNGER SS
11 2 WASHER SS
10 3 FLAT HEAD SCREW SS
9 2 BUTTON HEAD SCREW SS
8 1 RETAINING CLIP SS
7 1 STOP PLATE SS
6 1 LOCK WASHER SS
5 1 SHIELD CAB
4 1 INSULATION INSERT POLYSTYRENE
3 1 CAP POLYETHYLENE
2 1 SLEEVE FIRE RESISTANT ABS
1 1 HOUSING FIRE RESISTANT ABS
ITEM QTY. DESCRIPTION MATERIAL
REVISION HISTORY
REV DESCRIPTION ECN BY DATE CHKD
0 LARGE 3.44 7.00
TIH - K -940 2" BA-400 / BA-450 8301A/8311A
TIH - J1-940 2" BA-475 / BA-485 8901/8911
TIH - J -940
1" BA-400 / BA-450 8301A/8311A
1 1/4" , 1 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
2" BA-100 / BA-150 8501/8511
0 SMALL 3.06 4.50
TIH - H1-9401/2" BA-475 / BA-485 8901/8911
3/4",1", 1 1/4", 1 1/2" BA-475 / BA-485 8901/8911
TIH - F -9403/4" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
1" BA-100 / BA-150 8501/8511
TIH - D -940 1/4", 3/8", 1/2" BA-100 / BA-150 & BA-400 / BA-450 8501/8511 & 8301A/8311A
TIH - C1-940 1/4" , 3/8" BA-475 / BA-485 8901/8911
REV SIZE A B PART # SIZE(S) FITS MILWAUKEE LINE FITS HAMMOND LINE
NOTES:DIMENSIONS LISTED ARE IN ADDITION TO THE HEIGHT SHOWN IN THE CATALOG.1.DUE TO MANFACTURING PROCESSES, DIMENSIONS SHOWN ARE APPROXIMATE.2.
PART # SIZE(S) VALVE*Small TIH-C1-940 1/4", 3/8", 1/2" BA-475 / BA-485 / BA-480B / BA-490B Series
TIH-D-940 1/4", 3/8", 1/2" BA-100 / BA-150 / BA-400 / BA-450 SeriesTIH-D3-940 1/4", 3/8", 1/2" BA-300 / BA-350 Series
A - 4.50 1" BA-100 / BA-150 Series3/4" BA-100 / BA-150 / BA-400 / BA-450 Series
TIH-F3-940 3/4" BA-300 / BA-350 SeriesB - 3.06 TIH-H1-940 3/4",1",1 1/4", 1 1/2" BA-475 / BA-485 / BA-480B / BA-490B SeriesLarge 2" BA-100 / BA-150 Series
1 1/4", 1 1/2" BA-100 / BA-150/BA-400 / BA-450 Series1" BA-400 / BA-450 Series
A - 7.00 TIH-J1-940 2" BA-475 / BA-485 / BA-480B / BA-490B SeriesTIH-J3-940 1", 1 1/4", 1 1/2" BA-300 / BA-350 SeriesTIH-K-940 2" BA-400 / BA-450 Series
B - 3.44 TIH-K3-940 2" BA-300 / BA-350 Series
TIH-F-940
TIH-J-940
QTY. DESCRIPTION MATERIAL1 HOUSING FIRE RESISTANT ABS1 SLEEVE FIRE RESISTANT ABS1 CAP POLYETHYLENE1 INSULATION INSERT POLYSTYRENE1 SHIELD PLASTIC SLEEVE1 LOCK WASHER SS1 STOP PLATE & SCREWS SS1 MEMORY STOP ASSEMBLY SS
Bill of Material
R27752
To order factory assembled to the valve use suffix TIH (Threaded Only) Milwaukee Valve will not factory install (TIH) handle on solder end valves.*Will fit our equivalent Ultrapure Low Lead Valves.
Milwaukee Valve’s insulated extension handle is designed to prevent condensation and other extraneous moisture from entering your insulated piping system, while also minimizing thermal energy loss from the system via metal extension tubes, levers, and similar parts.
Our handle design incorporates a unique memory stop feature that requires no disassembly or removal of the handle to engage and make adjustments.
Rev. 7
Bronze & Brass Ball Valves
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-36MILWAUKEE VALVE
The information presented on this sheet is correct at the time of publication. Milwaukee Valve reserves the right to changedesign, and/or material specifications without notice. For the Installation, Operation and Maintenance Manual (IOM) see theengineering section on our website. For the most current information access www.milwaukeevalve.com
HOUSINGAND PLASTIC
SHIELD
CAP
INSULATION INSERT
INNER HOUSING WITHCALIBRATED MEMORY STOP
WASHER
MEMORY SET SCREWS C
M
Y
CM
MY
CY
CMY
K
Isolation Handle Assembly Instructions.pdf 1 10/29/14 11:20 AM
Rev. 2
*
* To order factory assembled to the valve use suffix TIH (Threaded Only) Milwaukee Valve will not factory install (TIH) handle on solder end valves.
Rev. 3
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-37
OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450
OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450
OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450
O 3/8”, Both Ends
OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450
OPTIONS
LockingOvalHandle
ChainLever
TeeHandle
H
L
W
Milwaukee offers two styles of oval handles,standard oval and a padlocking oval design.
Oval handles are intended for several differentapplications, they can be installed where a standard leverhandle might encounter interference from adjoining piping.Oval handles can also prevent accidental valveoperations, since they have less projection than a leverhandle, and require more turning force to operate. OSHArequires the use of oval handles in many installations forsafety reasons. The locking handle design willaccommodate a standard 5/16” pad-lock or other types ofvalve lockouts. The standard ovalhandle can be field or factory mountedon BA100/300/400 series valves up to2”, and the locking oval handlecan be used on sizes up to 1”.
Chain lever handle kits are designedfor installations where overheadball valves need to be operatedon a regular basis. A lengthof chain is attached to eitherend of the handle, so that theoperator needs only to pull down on the appropriatechain to open or close the valve.
L
H
L
Tee handles offer the sameinstallation space savings as oval
handles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
OH & LO
OvalHandle
L
W
H
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
BA100/150BA300/350BA400/450
OPTIONS
ExtensionStem
The “XH” stem extension is simpleand effective design. This option isdesigned for installations where pipeinsulation would make standardhandles inoperable. The stemextension can also be used where ahandle needs to be raised above an
adjoining obstruction. Installations wherethe valve is mounted behind a panel can be
an ideal place for the “XH” stem extension. The external plasticshield helps to keep the insulation away from the stemextension, providing years of trouble free operation.
Extension Handlewith MemoryStop
The “XM” stem extension is all-metallicwith an adjustable memory stop. Thisoption is designed for installationswhere pipe insulation would makestandard handles inoperable. The
stem extension can also be usedwhere a handle needs to be raised above anadjoining obstruction. Installations where the valve ismounted behind a panel can be an ideal place for the“XM” stem extension. The adjustable memory stopallows the valve opening to be limited to a presetposition. This option can be ordered with or withoutthe memory stop.
0
45
90
0
45
90
MemoryStop
The “MS” Memory Stop offers theconvenience of a preset stopwhen the valve is used in a
balancing application. Thememory stop can be setfrom the full closed position,to any preset opening point.
The “LD”Locking Handleoffers the end userthe security of a padlockable handle. Thehandle can be locked in eitherthe full open position, or fullclosed by adding a standardpadlock. OSHA requires the use oflocking handles in manyinstallations for safety reasons.The locking handle design willaccommodate a standard 5/16”pad-lock or other types of valve lockouts. Thehandle and locking device are also manufactured ofstainless steel material for additional strength andcorrosion resistance.
LockingDevice
BA100/150BA300/350BA400/450
OPTIONS
ExtensionStem
The “XH” stem extension is simpleand effective design. This option isdesigned for installations where pipeinsulation would make standardhandles inoperable. The stemextension can also be used where ahandle needs to be raised above an
adjoining obstruction. Installations wherethe valve is mounted behind a panel can be
an ideal place for the “XH” stem extension. The external plasticshield helps to keep the insulation away from the stemextension, providing years of trouble free operation.
Extension Handlewith MemoryStop
The “XM” stem extension is all-metallicwith an adjustable memory stop. Thisoption is designed for installationswhere pipe insulation would makestandard handles inoperable. The
stem extension can also be usedwhere a handle needs to be raised above anadjoining obstruction. Installations where the valve ismounted behind a panel can be an ideal place for the“XM” stem extension. The adjustable memory stopallows the valve opening to be limited to a presetposition. This option can be ordered with or withoutthe memory stop.
0
45
90
0
4590
MemoryStop
The “MS” Memory Stop offers theconvenience of a preset stopwhen the valve is used in a
balancing application. Thememory stop can be setfrom the full closed position,to any preset opening point.
The “LD”Locking Handleoffers the end userthe security of a padlockable handle. Thehandle can be locked in eitherthe full open position, or fullclosed by adding a standardpadlock. OSHA requires the use oflocking handles in manyinstallations for safety reasons.The locking handle design willaccommodate a standard 5/16”pad-lock or other types of valve lockouts. Thehandle and locking device are also manufactured ofstainless steel material for additional strength andcorrosion resistance.
LockingDevice
BA100/150BA300/350BA400/450
OPTIONS
ExtensionStem
The “XH” stem extension is simpleand effective design. This option isdesigned for installations where pipeinsulation would make standardhandles inoperable. The stemextension can also be used where ahandle needs to be raised above an
adjoining obstruction. Installations wherethe valve is mounted behind a panel can be
an ideal place for the “XH” stem extension. The external plasticshield helps to keep the insulation away from the stemextension, providing years of trouble free operation.
Extension Handlewith MemoryStop
The “XM” stem extension is all-metallicwith an adjustable memory stop. Thisoption is designed for installationswhere pipe insulation would makestandard handles inoperable. The
stem extension can also be usedwhere a handle needs to be raised above anadjoining obstruction. Installations where the valve ismounted behind a panel can be an ideal place for the“XM” stem extension. The adjustable memory stopallows the valve opening to be limited to a presetposition. This option can be ordered with or withoutthe memory stop.
0
45
90
0
45
90
MemoryStop
The “MS” Memory Stop offers theconvenience of a preset stopwhen the valve is used in a
balancing application. Thememory stop can be setfrom the full closed position,to any preset opening point.
The “LD”Locking Handleoffers the end userthe security of a padlockable handle. Thehandle can be locked in eitherthe full open position, or fullclosed by adding a standardpadlock. OSHA requires the use oflocking handles in manyinstallations for safety reasons.The locking handle design willaccommodate a standard 5/16”pad-lock or other types of valve lockouts. Thehandle and locking device are also manufactured ofstainless steel material for additional strength andcorrosion resistance.
LockingDevice
BA100/150BA300/350BA400/450
2 1/4” Height
OPTIONS
ExtensionStem
The “XH” stem extension is simpleand effective design. This option isdesigned for installations where pipeinsulation would make standardhandles inoperable. The stemextension can also be used where ahandle needs to be raised above an
adjoining obstruction. Installations wherethe valve is mounted behind a panel can be
an ideal place for the “XH” stem extension. The external plasticshield helps to keep the insulation away from the stemextension, providing years of trouble free operation.
Extension Handlewith MemoryStop
The “XM” stem extension is all-metallicwith an adjustable memory stop. Thisoption is designed for installationswhere pipe insulation would makestandard handles inoperable. The
stem extension can also be usedwhere a handle needs to be raised above anadjoining obstruction. Installations where the valve ismounted behind a panel can be an ideal place for the“XM” stem extension. The adjustable memory stopallows the valve opening to be limited to a presetposition. This option can be ordered with or withoutthe memory stop.
0
45
90
0
45
90
MemoryStop
The “MS” Memory Stop offers theconvenience of a preset stopwhen the valve is used in a
balancing application. Thememory stop can be setfrom the full closed position,to any preset opening point.
The “LD”Locking Handleoffers the end userthe security of a padlockable handle. Thehandle can be locked in eitherthe full open position, or fullclosed by adding a standardpadlock. OSHA requires the use oflocking handles in manyinstallations for safety reasons.The locking handle design willaccommodate a standard 5/16”pad-lock or other types of valve lockouts. Thehandle and locking device are also manufactured ofstainless steel material for additional strength andcorrosion resistance.
LockingDevice
BA100/150BA300/350BA400/450
2 1/4” Height
Rev. 6
Valve Series Valve Size Length WidthBA-100/150 1/4” - 1/2” 8 3/8” 1 1/4”BA-100/150 3/4" - 1" 11 1/2" 1 1/2"BA-100/150 1 1/4" - 3" 15 1/4" 2"
*BA300/350/400/450 1/4" - 1/2" 8 3/8" 1 1/4"*BA300/350/400/450 3/4" 11 1/2" 1 1/2"*BA300/350/400/450 1" - 1 1/2" 15 1/4" 2"
* Not Available above 1 1/2"
The information presented on this sheet is correct at time of publication. Milwaukee Valve reserves the right to change design and/or materials without notice. For our Installation, Operation and Maintenance Manual and the most current product information go to www.milwaukeevalve.com.
State of California Prop 65 WARNING: Cancer and Reproductive Harm. For more information visit www.p65warnings.ca.gov.
BV-38
OPTIONS*BA200/250
BA480B/BA490BBA-475B/485B
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" MV279521" - 1-1/4" MV279531-1/2"-2" MV27954
BA200BA250
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" MV279523/4"-1" MV27953
MV27954
BA475BBA485B
2-1/2"- 4" MV27955
2"- 3"Rev. 1
MV27955
The “XH” stem extension is a simple and effective design.This option is designed for installations where pipeinsulation would make standard handles inoperable.The stem extension can also be used where a handleneeds to be raised above an adjoining obstruction.Installations where the valve is mounted behind a panelcan be an ideal place for the “XH” stem extension.
XH ExtensionHandle SH
MemoryStop
The “MS” Memory Stop pr ovides an adjustable stopwhen the valve is used in a balancing application. The memory stop can be set to any preset opening point.
ValveSeries Valve Size Memory Stop
Number1/4"-1/2" 8662-D-9403/4"-1" 8662-F-9401-1/4" - 2" 8662-J-940
BA475B
BA485B
ValveSeries Valve Size Memory Stop
Number1/4" - 3/4" 8662-D-9401" - 1-1/4" 8662-F-9401-1/2" - 2" 8662-J-940
BA200
BA2502-1/2" - 4" 8662-K-940
2-1/2" - 3" 8662-K-940
ValveSeries Valve Size Stem Extension
Number1/4" - 3/4" EXTEN15X * 3"1" - 1-1/4" EXTEN25X * 3"1-1/2" - 2" EXTEN38X * 3"
BA200
BA2502-1/2" - 4" EXTEN50X * 3"
2" - 3" EXTEN50X * 3"
Height
Height
Height
3.304.655.287.88
3.304.655.287.88
.67.871.001.00
.67.87
1.001.00
ValveSeries Valve Size Stem Extension
Number1/4" - 1/2" EXTEN15X * 3"3/4" - 1" EXTEN25X * 3"
1-1/4" - 1-1/2" EXTEN38X * 3"
BA475B
BA485B
* Kits will fit both old and new style, all hardware included. Rev. 3
1-1/4"- 1-1/2"
OPTIONS*BA200/250
BA480B/BA490BBA-475B/485B
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" MV279521" - 1-1/4" MV279531-1/2"-2" MV27954
BA200BA250
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" MV279523/4"-1" MV27953
MV27954
BA475BBA485B
2-1/2"- 4" MV27955
2"- 3"Rev. 1
MV27955
The “XH” stem extension is a simple and effective design.This option is designed for installations where pipeinsulation would make standard handles inoperable.The stem extension can also be used where a handleneeds to be raised above an adjoining obstruction.Installations where the valve is mounted behind a panelcan be an ideal place for the “XH” stem extension.
XH ExtensionHandle SH
MemoryStop
The “MS” Memory Stop pr ovides an adjustable stopwhen the valve is used in a balancing application. The memory stop can be set to any preset opening point.
ValveSeries Valve Size Memory Stop
Number1/4"-1/2" 8662-D-9403/4"-1" 8662-F-9401-1/4" - 2" 8662-J-940
BA475B
BA485B
ValveSeries Valve Size Memory Stop
Number1/4" - 3/4" 8662-D-9401" - 1-1/4" 8662-F-9401-1/2" - 2" 8662-J-940
BA200
BA2502-1/2" - 4" 8662-K-940
2-1/2" - 3" 8662-K-940
ValveSeries Valve Size Stem Extension
Number1/4" - 3/4" EXTEN15X * 3"1" - 1-1/4" EXTEN25X * 3"1-1/2" - 2" EXTEN38X * 3"
BA200
BA2502-1/2" - 4" EXTEN50X * 3"
2" - 3" EXTEN50X * 3"
Height
Height
Height
3.304.655.287.88
3.304.655.287.88
.67.871.001.00
.67.87
1.001.00
ValveSeries Valve Size Stem Extension
Number1/4" - 1/2" EXTEN15X * 3"3/4" - 1" EXTEN25X * 3"
1-1/4" - 1-1/2" EXTEN38X * 3"
BA475B
BA485B
* Kits will fit both old and new style, all hardware included. Rev. 3
1-1/4"- 1-1/2"
OPTIONS*BA200/250
BA480B/BA490BBA-475B/485B
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" MV279521" - 1-1/4" MV279531-1/2"-2" MV27954
BA200BA250
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" MV279523/4"-1" MV27953
MV27954
BA475BBA485B
2-1/2"- 4" MV27955
2"- 3"Rev. 1
MV27955
The “XH” stem extension is a simple and effective design.This option is designed for installations where pipeinsulation would make standard handles inoperable.The stem extension can also be used where a handleneeds to be raised above an adjoining obstruction.Installations where the valve is mounted behind a panelcan be an ideal place for the “XH” stem extension.
XH ExtensionHandle SH
MemoryStop
The “MS” Memory Stop pr ovides an adjustable stopwhen the valve is used in a balancing application. The memory stop can be set to any preset opening point.
ValveSeries Valve Size Memory Stop
Number1/4"-1/2" 8662-D-9403/4"-1" 8662-F-9401-1/4" - 2" 8662-J-940
BA475B
BA485B
ValveSeries Valve Size Memory Stop
Number1/4" - 3/4" 8662-D-9401" - 1-1/4" 8662-F-9401-1/2" - 2" 8662-J-940
BA200
BA2502-1/2" - 4" 8662-K-940
2-1/2" - 3" 8662-K-940
ValveSeries Valve Size Stem Extension
Number1/4" - 3/4" EXTEN15X * 3"1" - 1-1/4" EXTEN25X * 3"1-1/2" - 2" EXTEN38X * 3"
BA200
BA2502-1/2" - 4" EXTEN50X * 3"
2" - 3" EXTEN50X * 3"
Height
Height
Height
3.304.655.287.88
3.304.655.287.88
.67.871.001.00
.67.87
1.001.00
ValveSeries Valve Size Stem Extension
Number1/4" - 1/2" EXTEN15X * 3"3/4" - 1" EXTEN25X * 3"
1-1/4" - 1-1/2" EXTEN38X * 3"
BA475B
BA485B
* Kits will fit both old and new style, all hardware included. Rev. 3
1-1/4"- 1-1/2"
2 1/4” Height
OPTIONS*BA200/250
BA480B/BA490BBA-475B/485B
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" MV279521" - 1-1/4" MV279531-1/2"-2" MV27954
BA200BA250
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" MV279523/4"-1" MV27953
MV27954
BA475BBA485B
2-1/2"- 4" MV27955
2"- 3"Rev. 1
MV27955
The “XH” stem extension is a simple and effective design.This option is designed for installations where pipeinsulation would make standard handles inoperable.The stem extension can also be used where a handleneeds to be raised above an adjoining obstruction.Installations where the valve is mounted behind a panelcan be an ideal place for the “XH” stem extension.
XH ExtensionHandle SH
MemoryStop
The “MS” Memory Stop pr ovides an adjustable stopwhen the valve is used in a balancing application. The memory stop can be set to any preset opening point.
ValveSeries Valve Size Memory Stop
Number1/4"-1/2" 8662-D-9403/4"-1" 8662-F-9401-1/4" - 2" 8662-J-940
BA475B
BA485B
ValveSeries Valve Size Memory Stop
Number1/4" - 3/4" 8662-D-9401" - 1-1/4" 8662-F-9401-1/2" - 2" 8662-J-940
BA200
BA2502-1/2" - 4" 8662-K-940
2-1/2" - 3" 8662-K-940
ValveSeries Valve Size Stem Extension
Number1/4" - 3/4" EXTEN15X * 3"1" - 1-1/4" EXTEN25X * 3"1-1/2" - 2" EXTEN38X * 3"
BA200
BA2502-1/2" - 4" EXTEN50X * 3"
2" - 3" EXTEN50X * 3"
Height
Height
Height
3.304.655.287.88
3.304.655.287.88
.67.871.001.00
.67.87
1.001.00
ValveSeries Valve Size Stem Extension
Number1/4" - 1/2" EXTEN15X * 3"3/4" - 1" EXTEN25X * 3"
1-1/4" - 1-1/2" EXTEN38X * 3"
BA475B
BA485B
* Kits will fit both old and new style, all hardware included. Rev. 3
1-1/4"- 1-1/2"
OPTIONS*BA200/250
BA480B/BA490BBA-475B/485B
StainlessSteelHandle
The “SH” handle option adds a 316stainless steel handle and nut to astandard bronze ball valve. This option isintended for harsh environments likeareas subject to salt water spray, highhumidity, harsh cleaning chemicals, etc.
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" MV279521" - 1-1/4" MV279531-1/2"-2" MV27954
BA200BA250
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" MV279523/4"-1" MV27953
MV27954
BA475BBA485B
2-1/2"- 4" MV27955
2"- 3"Rev. 1
MV27955
The “XH” stem extension is a simple and effective design.This option is designed for installations where pipeinsulation would make standard handles inoperable.The stem extension can also be used where a handleneeds to be raised above an adjoining obstruction.Installations where the valve is mounted behind a panelcan be an ideal place for the “XH” stem extension.
XH ExtensionHandle SH
MemoryStop
The “MS” Memory Stop pr ovides an adjustable stopwhen the valve is used in a balancing application. The memory stop can be set to any preset opening point.
ValveSeries Valve Size Memory Stop
Number1/4"-1/2" 8662-D-9403/4"-1" 8662-F-9401-1/4" - 2" 8662-J-940
BA475B
BA485B
ValveSeries Valve Size Memory Stop
Number1/4" - 3/4" 8662-D-9401" - 1-1/4" 8662-F-9401-1/2" - 2" 8662-J-940
BA200
BA2502-1/2" - 4" 8662-K-940
2-1/2" - 3" 8662-K-940
ValveSeries Valve Size Stem Extension
Number1/4" - 3/4" EXTEN15X * 3"1" - 1-1/4" EXTEN25X * 3"1-1/2" - 2" EXTEN38X * 3"
BA200
BA2502-1/2" - 4" EXTEN50X * 3"
2" - 3" EXTEN50X * 3"
Height
Height
Height
3.304.655.287.88
3.304.655.287.88
.67.871.001.00
.67.87
1.001.00
ValveSeries Valve Size Stem Extension
Number1/4" - 1/2" EXTEN15X * 3"3/4" - 1" EXTEN25X * 3"
1-1/4" - 1-1/2" EXTEN38X * 3"
BA475B
BA485B
* Kits will fit both old and new style, all hardware included. Rev. 3
1-1/4"- 1-1/2"
OPTIONS BA200/250BA475B/485B
handle might encounter interference from adjoiningpiping. Oval handles can also prevent accidental valveoperations, since they have less projection than a lever
ValveSeries
ValveSize
HandlePart
Number Style Length Width Height1/4" - 3/4" 26561MV1" - 1-1/4" 26562MV1-1/2"-2" 26563MV1/4"-1/2" 26561MV3/4"-1" 26562MV
26563MV
BA475B
OvalBA200
OvalHandle
L
W
H
Oval handles can be installed where a standard lever
2.81 1.72 .664.38 2.72 .93
4.38 2.72 .933.58 2.26 .72
2.81 1.72 .663.58 2.26 .72
Oval
handle, and require more turning force to operate.The standard oval handle can be field or factory mountedon BA-200/BA-475B series valves up to 2”.
BA250
BA485B
TeeHandle
Tee handles offer the sameinstallation space savings as ovalhandles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" 26564MV3/4"-1" 26565MV
26566MV
BA475BBA485B
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" 26564MV1" - 1-1/4" 26565MV1-1/2" - 2" 26566MV
BA200BA250
2.903.804.00
.67
1.00.87
2.903.804.00
.67
.871.00
1-1/4"- 1-1/2"
1-1/4"- 1-1/2" Rev. 1
Rev. 1
OPTIONS BA200/250BA475B/485B
handle might encounter interference from adjoiningpiping. Oval handles can also prevent accidental valveoperations, since they have less projection than a lever
ValveSeries
ValveSize
HandlePart
Number Style Length Width Height1/4" - 3/4" 26561MV1" - 1-1/4" 26562MV1-1/2"-2" 26563MV1/4"-1/2" 26561MV3/4"-1" 26562MV
26563MV
BA475B
OvalBA200
OvalHandle
L
W
H
Oval handles can be installed where a standard lever
2.81 1.72 .664.38 2.72 .93
4.38 2.72 .933.58 2.26 .72
2.81 1.72 .663.58 2.26 .72
Oval
handle, and require more turning force to operate.The standard oval handle can be field or factory mountedon BA-200/BA-475B series valves up to 2”.
BA250
BA485B
TeeHandle
Tee handles offer the sameinstallation space savings as ovalhandles, with a slightly shorter endto end dimension. Tee handlesrequire more handle force tooperate, so accidental openings canbe reduced.
ValveSeries Valve Size Handle Part
Number Length Width
1/4"-1/2" 26564MV3/4"-1" 26565MV
26566MV
BA475BBA485B
ValveSeries Valve Size Handle Part
Number Length Width
1/4" - 3/4" 26564MV1" - 1-1/4" 26565MV1-1/2" - 2" 26566MV
BA200BA250
2.903.804.00
.67
1.00.87
2.903.804.00
.67
.871.00
1-1/4"- 1-1/2"
1-1/4"- 1-1/2" Rev. 1
Rev. 1
*Locking Lever Handle Is Available.
Rev. 2
Physical Address 1509 Riverport RoadKingsport, TN 37660
Physical Address 400 Natalie Boulevard
Loudon, TN 37774
Kingsport TN: 423-765-9991 | Loudon TN: 865-458-2333
FOR QUESTIONS OR TO REQUEST A QUOTE, VISIT WWW.PROCESSSUPPLY.COM OR CALL
W E A R E A V A I L A B L E 2 4 / 7