vrc2010 tester manual 2015

VRC2010

Tester Manual

2015C

M

Y

CM

MY

CY

CMY

K

• Capable of testing A and B type regulators• Test 12 Volt type regulators at 0.5A and 3A• Test 24 Volt regulators at 1A field current• Universal power supply, 100 to 240 volts,

47-64hz• Voltmeter display• Short-circuit protected• Dual stator test capability• “C” function test• Choke test• Over voltage lamp test

• LIN/BSS test capability at 13,14 and 15 Volts

• Ford PCM test capability 13, 14, 15 Volts• Test PD type regulators• Robust and stackable metal box • Universal tester adapter plus VRC2010-002

(included)• Additional tester adapter plugs available for

testing Bosch, Denso, Ford, Mando, Marelli, Mitsubishi, Valeo type voltage regulators

VRC2010-003

VRC2010-001VRC2010-005

VRC2010-002

VRC2010-004VRC2010-006

Voltage Regulator Tester & Harnesses

VRC2010

for

TRANSPO TESTER INSTRUCTIONStype regulatorsCHRYSLER

VOLTFLD SET POINTPART NO.

C8312

C8313

C8315

A

A

A

12

12

12

14.3

14.2

14.2


3. Amendments or Additional Tests:

1. POWER OFF:

2. POWER ON:

Set ‘FLD’ switch and ‘Voltage Range’ switch to compatible setting. Connect the Voltage Regulatoras indicated in the diagram or as described in the ‘Amendments or Additional Test’ notes.

Tester field lamp should blink and tester meter should indicate the approximiate Set PointVoltage noted in the table above.

N/A

11/21/2014Revision: Date :C-01Product Group1Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsCHRYSLER


C8010

C8012

B

B

12

12

14.3

14.0



1. POWER OFF:

2. POWER ON:



N/A

11/21/2014Revision: Date :C-02Product Group 3/12/19992Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsC.A.V.


CE520

CE520

CE520

A

A

A

24

24

24

HI 28.8

MID 27.8

LO 26.7



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :CE-01Product Group 3/10/19993Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsC.A.V.


CE301 A 12 14.3



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :CE-03Product Group 3/8/19994Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsDAEWOO


D403 A 12 14.7



1. POWER OFF:

2. POWER ON:



D403 Special Note: POWER ON field lamp may blink or illuminate steady-on to indicate a functional circuit.

D403 Special Note: POWER ON field lamp may blink or illuminate steady-on to indicate a functional circuit.

11/21/2014Revision: Date :DA-01Product Group 10/22/19075Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsDELCO


D32S

D10SE6

D105

D105HD

A

A

A

A

32

6

12

12

37.5

7.7

14.8

14.8


D10SE12

D101

D101HD

A

A

A

12

12

12

14.8

14.8

14.8


1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :D-02Product Group6Page

for



D17SE

D102HD

D30S

D27

A

A

A

A

12

12

24

12

14.2

13.7

27.5

13.7


D27S A 12 14.0


1. POWER OFF:

2. POWER ON:




for



D9212

D9212S

D9212C

D6374

B

B

B

B

12

12

12

12

14.2

14.2

14.2

14.6


D6378

D6377

D518

B

B

B

12

12

24

14.6

14.6

27.5


1. POWER OFF:

2. POWER ON:



On all above parts numbers except D6377, disconnect red test lead from the terminal marked with "S" Indicatorlight should turn on and the meter will indicate set point voltage.

11/21/2014Revision: Date :D-06Product Group 5/1/19978Page

for



D443

D447

D551

D597

B

B

B

B

12

24

12

24

14.2

27.5

14.2

27.5



1. POWER OFF:

2. POWER ON:




for



D551P

D597P

B

B

12

24

14.2

27.5



1. POWER OFF:

2. POWER ON:




for



D443P

D447P

B

B

12

24

14.2

27.5



1. POWER OFF:

2. POWER ON:




for



D437P

D559P

A

A

24

12

27.5

12.2



1. POWER OFF:

2. POWER ON:




for



D437

D559

A

A

24

12

27.5

14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked with (*) . Field lamp should turn off and the meter will indicate lowvoltage.


for



D408XHD

D411XHD

*D440G

B

B

B

12

12

12

14.8

14.8

14.7



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STATOR". The indicator light will turn on, field lamp will stay on and meter willindicate approximately 12V. Disconnect the test lead from "L" terminal. Regulator will turn off and the meter will indicate 12V.To check for over Voltage, push the “Over Voltage” switch and the “Lamp Indicator” will turn on between 16.0V and 17.1V.Push the choke drive and the “Choke Drive Indicator Lamp” will turn on, if present.

NOTE: On D440 regulator, both of the "L" and "I" terminals must be connected in order to conduct the test.


for



D412 *

D413

D440 **

D425

B

B

B

B

12

12

12

12

14.2

14.7

14.7

14.2


D446

D411SE

B

B

12

12

14.6

14.7


1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STATOR". The indicator light will turn on, field lamp will stay onand meter will indicate approximately 12V. Disconnect the test lead from "L" terminal. Regulator will turn off andthe meter will indicate 12V. On "I" type voltage regulators, connect the regulators as per diagram below except donot connect the indicator light to the "L" terminal. Connect red test lead to the terminal marked "I/F" and sameresults as step number 2 should be noticed.

*NOTE: On D412 regulator , an 1800 OHM pull-up resistor is required between "S" terminal of regulator and thetesters battery POS.**NOTE: On D440 regulator, both of the "L" and "I" terminals must be connected in order to conduct the test.


for



D812

D817

D824

A

A

A

12

12

24

14.2

14.2

27.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from the regulator's yellow wire. Field lamp should turn off and the meter will indicate lowvoltage. Also, connection the red test lead to "NO CONNECTION" terminal instead of regulator's red wire willresult in the same test data.


for



D710

D713

D173L

B

B

B

6

12

12

7.8

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator". Field lamp should turn off and the meter will indicate lowvoltage. On D713L regulator, removal of white test leads will also cause indicator light to turn on.


for



D590S

D591S

D593S

B

B

B

12

24

32

14.2

27.5

37.5



1. POWER OFF:

2. POWER ON:




for



D812

D812HD

D813

D813HD

A

A

A

A

12

12

12

12

14.2

14.2

14.2

14.2


D824

D824HD

D832

A

A

A

24

24

32

27.5

27.5

37.5


1. POWER OFF:

2. POWER ON:




for



D817

D817HD

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



D7018

D7019

A

A

12

24

14.2

27.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from regulator's wire marked "stator". Field lamp should turn off and the meter willindicate low voltage.


for



DE606

DE607

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



D424 B 12 14.7



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "stator". The indicator light will turn on, field lamp will stay on andmeter will indicate approximately 12V. Disconnect the test lead from "L" terminal . Regulator will turn off and themeter will indicate 12V.


for



D9206

D9207

B

B

6

6

7.8

7.8



1. POWER OFF:

2. POWER ON:



On D9207, remove test lead from the terminal marked "STA". Field lamp will turn off , indicator light will turn on,and the meter will indicate low voltage.


for



DE611

DE615

A

A

12

12

14.7

14.7



1. POWER OFF:

2. POWER ON:




for



D7050 B 12 14.7



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator". Regulator will turn off and the meter will indicate 12V.


for



DE701

DE701HD

A

A

12

12

14.7

14.7



1. POWER OFF:

2. POWER ON:




for



D702XHD

D703XHD

D705XHD

D706XHD

B

B

B

B

12

12

12

12

14.5

14.5

14.7

14.1



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator". The indicator light will turn on, field lamp will stay on andthe meter will indicate approximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



D33

D22

A

A

12

12

14.1

14.5



1. POWER OFF:

2. POWER ON:




for



D401 A 24 27.7



1. POWER OFF:

2. POWER ON:




for



D698

D699

B

B

12

24

14.2

27.5



1. POWER OFF:

2. POWER ON:




for



D445 B 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator. The indicator light will turn on, field lamp will stay on andthe meter will indicate approximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



D10AC

D22AC

B

B

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



D712

D718

D719

D729

B

B

B

B

12

12

12

12

14.6

14.7

14.75

14.75


D734

D749

D748

D752

B

B

B

B

12

12

12

12

14.6

14.6

14.8

14.7


1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator". the indicator light will turn on, field lamp will stay on andmeter will indicate approximately 12v. Disconnect the test lead from "L" terminal. Regulator will turn off and themeter will indicate 12v. On "I" type voltage regulators, connect the regulators as per diagram below except do notconnect the indicator light to the "L" terminal. Connect red test lead to the terminal marked "I/F" and same resultsas step number 2 should be noticed.


for



D198XHD

D200XHD

D201XHD

D202XHD

B

B

B

B

12

12

12

12

14.8

14.8

14.8

14.8


D203XHD B 12 14.8


1. POWER OFF:

2. POWER ON:



Remove Stator terminal, field light stays on voltage reads 12 volts and lamp light comes on. Remove lightterminal (and "I" terminal on PLIS type), voltage regulator turns off.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsFORD


F540

F540HD

F540S

F540SLD

B

B

B

B

12

12

12

12

14.3

14.2

14.3

14.2


F540SP

F540XHD

F782

F783

B

B

B

B

12

12

12

12

14.2

14.2

14.2

14.3


1. POWER OFF:

2. POWER ON:



Remove red lead from terminal marked "S". Indicator light should turn on and meter will still indicate set pointvoltage. Removal of test lead from "S" and "I" terminal will result in the field lamp turning off and the meterreading 12V. On Mechanical type regulators (F8512M), the "short circuit" light will also turn on due to theregulator's internal circuitry. Limit this test to a short time.

11/21/2014Revision: Date :F-01Product Group36Page

for



F784

F784HD

F794

F784B

A

A

A

A

12

12

12

12

14.6

14.6

14.6

14.6


F785

F786

F794B

F795

A

A

A

A

12

12

12

12

14.6

14.6

14.6

14.6


1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator light should turn on and the meter will still indicate theset point voltage. Removal of test of leads from "S" and " I" will result in field lamp turning off and the meterreading 12V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.

NOTE: On Transpo's F786 & F795 connect white test lead to terminal marked "S".

11/21/2014Revision: Date :F-03Product Group 4/26/190537Page

for



F733L B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "stator". Field lamp should turn off and the meter will indicate lowvoltage. On F733L regulator, removal of white test lead will result in indicator light turning on.

* NOTE: No Yellow wire for F733


for



FB123

FB303

FB309

B

B

B

12

12

12

14.2

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from blue wire of the regulator. Field lamp should turn off and the meter will indicate 12V.


for



F7078 B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked " Stator". Field lamp should turn off, indicator light will turn on andthe meter will indicate low voltage.


for



F796 A 12.0 14.6



1. POWER OFF:

2. POWER ON:



To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



F600 A 12.0 14.3



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked “Stator”, field light stays on, voltage remains at 14.3 volt andindicator light turns on. Remove green test lead from “Light” terminal, field light and 12.0 volt light turn off.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



F798 A 12.0 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from stator and voltage will remain the same and 12 volt lamp will come on.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



F602

F603

F605

F606

A

A

A

A

12.0

12.0

12.0

12.0

14.4

14.4

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked “Stator”, field light stays ON. On F602 voltage drops to 12.0 volts and indicatorlight turns ON. On F603 voltage stays at 14.4 volts and lamp turns ON. Remove green test lead from “Light” terminal, fieldlight and lamp turn OFF.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0V and 17.1V.Note: F605 Disconnect sense terminal, regulator should read aproximately 14.8V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsHARLEY


H0478

H0482

A

A

12

12

15.1

15.1



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :H-01Product Group45Page

for



H606

H614

A

A

6

12

7.5

15.1



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :H-02Product Group 5/28/190446Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsBOSCH


IB371 A 12 14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IB-01Product Group 5/18/190547Page

for



IB8315 A 12 14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IB-03Product Group48Page

for



IB303

IB303A

B

B

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:




for



IB375

IB376

IB377

IB378

A

A

A

A

12

24

12

12

14.4

27.5

14.4

14.4


IB379

IB374

A

A

24

24

28.1

27.5


1. POWER OFF:

2. POWER ON:




for



IB380

IB383

IB384

IB385

A

A

A

A

12

12

12

12

14.4

14.4

14.4

14.5


IB387 A 12 14.5


1. POWER OFF:

2. POWER ON:




for



IB033A B 24 28.3



1. POWER OFF:

2. POWER ON:




for



IB305

IB306

B

B

12

12

14.8

14.8



1. POWER OFF:

2. POWER ON:



NOTE: IB306 Superseded by IB305-1


for



IB308 B 24 28.0



1. POWER OFF:

2. POWER ON:




for



IB343 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STA"; meter will indicate set point and lamp light will come on. Reconnect thewhite test lead. Remove red test lead from the terminal marked "SENSE", the meter will indicate 12V, field lamp will stay onand lamp light will come on. Remove green test lead; field and lamp light will turn off.To check for over Voltage, push the “Over Voltage” switch and the “Lamp Indicator” will turn on between 16.0V and 17.1V.


for



IB348

IB350

IB351

IB352

A

A

A

A

12

12

12

12

15.0

14.1

14.5

14.1


IB353

IB354

IB355

IB356

A

A

A

A

12

12

12

12

14.5

14.1

14.5

14.8


1. POWER OFF:

2. POWER ON:




for



IB370

IB370A

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



IB365 A 24 28.5



1. POWER OFF:

2. POWER ON:




for



IB386 A 28 28



1. POWER OFF:

2. POWER ON:




for



IB398 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IB382

IB381

IB316

A

A

A

24

24

24

28.8

28.1

28.5



1. POWER OFF:

2. POWER ON:




for



IB511 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IB512 A 12 14.6



1. POWER OFF:

2. POWER ON:




for



IB388 A 12 14.0



1. POWER OFF:

2. POWER ON:




for



IB501 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IB399 A 12 14.2



1. POWER OFF:

2. POWER ON:




for



IB400 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IB360

IB368

IB362

IB363

A

A

A

A

12

12

24

24

14.1

14.1

28.00

28.5


IB364

IB369

IB366-1

A

A

A

24

24

24

29.0

28.0

28.5


1. POWER OFF:

2. POWER ON:




for



IB225

IB247

A

A

12

12

14.5

14.3



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.• Push the Choke switch and the "Choke Drive" will turn on.• Remove white test lead from terminal marked "Stator" - the Field light and Lamp will come on and

Voltage will show 12 volts.• Remove green test lead from "light" terminal , field light will go out and voltage stays at 12 volts.

• To check IB247 for Over Voltage using VRC2010, push the “Over Voltage” switch and the “Lamp Indicator” willturn on between 16.0V and 17.1V.• L-FR Terminals • With LRC and Soft Start • Active Lamp Circuit - with OutputNOTE: VRC101-34 adapter shown for enhance stator signal, not all late model regulators need enhance signal


for



IB392

IB391

A

A

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove Red test lead from terminal marked "STA". lamp comes on and the meter will indicate set point voltage.Reconnect the white test lead. Remove red test lead from the terminal marked "S", field lamp will turn on, theindicator light will turn on and the meter will indicate 12V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsDELCO STAR II & STAR


D7011

D7012

D7014

D7016

B

B

B

B

6

8

12

24

7.8

9.6

14.2

27.5



1. POWER OFF:

2. POWER ON:



Disconnect white test lead (Stator) from regulator's yellow wire. Field lamp should turn "OFF" and the meter willindicate the original voltage range in step one.

Note: Indicator light will turn "ON" on part numbers: D7011, D7014, D7016, D7041.

Regulator Wire Test Lead Wire FunctionRed Red Battery PositiveBlack Black Battery NegativeGreen Yellow FieldYellow White Stator

11/21/2014Revision: Date :ST-D-42Product Group71Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsDELCO STAR II & STAR


D7044

D7024

B

B

12

12

14.7

14.2



1. POWER OFF:

2. POWER ON:



Disconnect white test lead (Stator) from regulator's yellow wire. Field lamp should turn "OFF" and the meter willindicate the original voltage range in step one.

Note: Indicator light will turn "ON" on part numbers: D7044, D7021, D7024, D7026.

Regulator Wire Test Lead FunctionRed Red Battery PositiveBlack Black Battery NegativeGreen Yellow FieldYellow White Stator

11/21/2014Revision: Date :ST-D-43Product Group72Page

for



IB241 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator" volts will drop to 12 volts; field light and lamp light willcome on. Remove green test lead from terminal marked "light", field and lamp light will go out and voltageremains at 12 volts.To check for over Voltage, push the “Over Voltage” switch and the “Lamp Indicator” will turn on between 16.0Vand 17.1V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsDUCELLIER


ID1006

ID1010

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from the blue wire of the regulator. Indicator light should turn on and the meter will stillindicate the set point voltage.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.

11/21/2014Revision: Date :ID-01Product Group 4/26/190574Page

for



ID4009 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



ID1015 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



ID1004

ID1016

A

A

14

14

14.3

14.4



1. POWER OFF:

2. POWER ON:



Disconnect red test lead from stator (blue) wire indicator lamp will come on regulator will continue to read14.4/14.5 volts. Reconnect stator lead and lamp will go out.


for



ID1007 A 12 14.4



1. POWER OFF:

2. POWER ON:



Disconnect red test lead from stator (blue) wire indicator lamp will come on regulator will continue to read14.4/14.5 volts. Reconnect stator lead and lamp will go out.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



ID1011 A 12 14.4



1. POWER OFF:

2. POWER ON:



Disconnect red test lead from stator (blue) wire indicator lamp will come on regulator will continue to read14.4/14.5 volts. Reconnect stator lead and lamp will go out.


for



ID1018 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from the blue wire of the regulator. Indicator light should turn on the meter will still indicatethe set point voltage.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsFEMSA


IF8603

IF8607

A

A

12

12

14.7

14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IF-01Product Group 5/1/199781Page

for



IF5442 A 12 14.2



1. POWER OFF:

2. POWER ON:



Remove red lead from terminal marked stator. Indicator light will come on, reconnect. Light shuts off.


for



IF1692 A 12 14.7



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsHITACHI


IH605 B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from the terminal marked "STA". Warning light will turn on and meter should set pointvoltage.

11/21/2014Revision: Date :IH-01Product Group84Page

for



IH209

IH210

IH210HD

IH211

A

A

A

A

12

12

12

12

14.7

14.3

14.2

14.7


IH212

IH213

A

A

12

12

14.3

14.3


1. POWER OFF:

2. POWER ON:




for



IH201

IH202

IH203

A

A

A

12

12

12

14.3

14.3

14.3



1. POWER OFF:

2. POWER ON:




for



IH214

IH215

IH707

A

A

A

12

12

24

14.4

14.2

28.5



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IH-04Product Group 10/27/190087Page

for



IH811

IH814

IH820

B

B

B

12

12

12

14.3

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove test lead from terminal marked "STA" Indicator light should turn on and the meter will still indicate theset point voltage.


for



IH237

IH238

IH239

A

A

A

12

12

12

14.6

14.6

14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 15.5V.


for



IH833 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove test lead from terminal marked "STA". Indicator light should turn on and the meter will still indicate theset point voltage.


for



IH815

IH816

IH830

B

B

B

12

12

12

14.3

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove test lead from terminal marked "STA" Indicator light should turn on and the meter will still indicate the setpoint voltage.


for



IH240 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" Field lamp should still blink and the meter will indicateapproximately 15.5V.


for



IH245 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal "S" Field lamp should still blink and the meter will indicate approximately 15.5V.


for



IH241

IH244

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:





for



IH243

IH246

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:





for



IH242 A 12 14.6



1. POWER OFF:

2. POWER ON:





for



IH247 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STA". Indicator light should turn on, field lamp will remain on andmeter will indicate approximately 12V. Remove red test lead from terminal marked "IG". Field lamp should turnoff.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH248 A 12 14.4



1. POWER OFF:

2. POWER ON:





for



IH832 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove black test lead from terminal marked "STA". Indicator lamp should turn on and the meter will still indicatethe set point voltage.


for



IH717 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IH250 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 1 volt higher than set point.


for



IH708 A 24 28.7



1. POWER OFF:

2. POWER ON:



Connect a red test lead to the terminal marked "C". The field lamp should still blink and the meter will indicateapproximately 26.3 V.


for



IH760 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Filed lamp should still blink and the meter will indicateapproximately 15.5 volts.


for



IH761 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator". 12V lamp should illuminate and the meter will indicateapproximately 12.0 V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH249 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should blink and the meter will indicate approximately15.5V.


for



IH251 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should blink and the meter will indicate approximately15.5V.


for



IH252 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove sense. Voltage goes to 15.6V and field light stays on.


for



IH762 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STA". Field lamp will remain fully on and the meter should indicate12V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH765

IH767

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator". 12V lamp should illuminate and the meter will indicateapproximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH205 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove (Red) Sense lead, voltage should go to 15.5V.


for



IH254 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove (Red) lead from sense , Field lamp will stay on, voltage will rise between 15.5V and 15.9V.


for



IH766 A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect "S", Voltage stays the same , 12V lamp comes on and field lamp continues to be on and field lampcontinues to be on.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH770 A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect "S", voltage goes to approximately 15.2V Field lamp stays on.


for



IH776 A 12 14.2



1. POWER OFF:

2. POWER ON:



Remove white lead from stator, field circuit lamp will stay on. 12V lamp will come on and voltage will drop to 12V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH782 A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect (white ) lead from stator, voltage drops to 12V and lamp comes on. Disconnect (Red) lead fromsense, lamp comes on and rises to 15.5V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH763 A 12 14.2



1. POWER OFF:

2. POWER ON:



Remove red lead from terminal marked "S" and voltage will rise to approximately 15.5V. Remove stator and lampcomes on and voltage drops to 12V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IH772 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove stator and lamp comes on. Apply ground to "C" Terminal and voltage will drop to 12.5 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsISKRA


IK404 A 24 28.0



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IK-01Product Group 3/12/1999118Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsISKRA


IK401 A 12 14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IK-02Product Group 3/12/1999119Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsLUCAS


IL211

IL213

IL217

A

A

A

12

12

12

14.2

14.2

14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IL-01Product Group 5/1/1997120Page

for



IL214

IL215

IL216

IL218

A

A

A

A

12

12

12

12

14.2

14.2

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



IL223

IL225

IL223CN-B128

A

A

A

12

24

12

14.3

28.1

14.3



1. POWER OFF:

2. POWER ON:




for



IL224 A 12 12.5



1. POWER OFF:

2. POWER ON:




for



IL219

IL220

IL221

IL222

A

A

A

A

12

12

12

12

14.3

14.3

12.3

14.3



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IL-05Product Group124Page

for



IL1292 B 12 14.3



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsMITSUBISHI


IM204

IM204HD

IM205

IM225

A

A

A

A

12

12

12

12

14.6

14.6

14.6

14.3



1. POWER OFF:

2. POWER ON:



On IM225 regulator, remove red test lead from terminal marked "*". Field lamp should still blink and the meterwill indicate approximately 15.4V.

11/21/2014Revision: Date :IM-01Product Group 8/15/1997126Page

for



IM224 A 12 14.2



1. POWER OFF:

2. POWER ON:



Connect another black test lead to terminal marker "Quick Start". Field lamp should still blink and the meter willindicate approximately 13.0V.

11/21/2014Revision: Date :IM-02Product Group127Page

for



IM216

IM216HD

IM289

IM217HD

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.3


IM217 A 12 14.3


1. POWER OFF:

2. POWER ON:



On IM217 Regulator, remove red test lead from terminal marked "*". Field lamp should still blink and the meterwill indicate approximately 15.4V.


for



IM268

IM270

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



On IM268, removal of red test lead from terminal marked "A" should result in the indicator light to turn on and themeter will indicate approximately 15.7V. On IM270, Removal of test lead "A" terminal should result in the meterto indicate approximately 15.7V.


for



IM542

IM951

IM954

IM952

B

B

B

B

12

12

12

12

14.3

14.3

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove Red test lead from terminal marked "STA". Indicator light should turn on and the meter will indicate theset point voltage.


for



IM261

IM269

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



On IM261, remove red test lead from the terminal marked "*". Field lamp should still blink and the meter willindicated approximately 15.4 v.

IM261: S-L TerminalsIM269: R-L Terminals


for



IM604 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "STA". Indicator light should turn on and the meter will indicate setpoint voltage.


for



IM262

IM263

IM265

IM265HD

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 1.5V above the set point voltage.


for



IM266

IM266HD

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



IM267 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "C" and connect a black test lead to it . Field lamp should still blinkand the meter will indicate approximately 12.5V.


for



IM271 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink, indicator light turn on and the meterwill indicate approximately 15.5V.


for



IM272 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "A". Field lamp should still blink , indicator light will turn on and themeter will indicate approximately 15.5V.


for



IM274 A 12 14.4



1. POWER OFF:

2. POWER ON:





for



IM277

IM278

IM279

A

A

A

12

12

12

14.5

14.5

14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 15.5V. (on IM277 & IM279 indicator light will turn on.)


for



IM226 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IM215 A 24 28.5



1. POWER OFF:

2. POWER ON:




for



IM227 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IM207

IM213

A

A

12

24

14.5

28.4



1. POWER OFF:

2. POWER ON:




for



IM212

IM208

A

A

24

12

28.4

14.5



1. POWER OFF:

2. POWER ON:




for



IM214 A 24 28.7



1. POWER OFF:

2. POWER ON:




for



IM206 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IM273

IM839

IM835

A

A

A

12

12

12

14.4

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "TRIO". field lamp should still blink indicator light will turn on andmeter will indicate the set point voltage.

Reconnect red test lead to terminal marked "Trio". Connect black test lead to "C" terminal. Field lamp should stillblink and meter will indicate approximately 12.5V.


for



IM282

IM281

A

A

12

12

14.4

14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". field lamp should still blink and the meter will indicatedapproximately 15.5V.


for



IM280

IM837

A

A

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" Indicator lamp should turn on, will still blink, and the meter willindicate approximately 15.5V.Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for



IM209 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" field lamp will still blink, and the meter will indicate approximately15.5V.


for



IM210 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp will still blink, and the meter will indicateapproximately 15.5V.


for



IM276 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator light will turn on, Field lamp will still blink, and themeter will indicate approximately 15.5V.


for



IM287 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". The meter will indicate approximately 15.5V.


for



IM283 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IM829 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator lamp should turn on, field lamp will still blink, and themeter will indicate approximately 15.5V.


for



IM830 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator lamp should turn on, field lamp will still blink, and themeter will indicate approximately 15.5V. and the lamp will turn on.


for



IM285 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 15.5 volts.


for



IM288 A 12 14.6



1. POWER OFF:

2. POWER ON:





for



IM291 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" Indicator lamp should turn on, field lamp will still blink, and themeter will indicate approximately 15.5V.


for



IM292 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" field lamp will still blink, and the meter will indicate approximately15.5V.


for



IM832 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator lamp should turn on, field lamp will still blink, and themeter will indicate approximately 15.5V.


for



IM275

IM834

A

A

12

12

14.7

14.7



1. POWER OFF:

2. POWER ON:




for



IM836 A 14 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "A". Field lamp should still blink, indicator light will turn on and themeter will indicate approximately 15.5V.


for



IM290 A 12 14.7



1. POWER OFF:

2. POWER ON:




for



IM830HD A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink, indicator light will turn on and themeter will indicate approximately 15.5 volts.


for



IM840 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red sense lead & indicator light will turn on & Voltage will rise to 15.5 volts.


for



IM293 A 12 14.7



1. POWER OFF:

2. POWER ON:




for



IM831 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Field lamp should still blink and the meter will indicateapproximately 15.5 volts.


for



IM845 A 12 14.7



1. POWER OFF:

2. POWER ON:



Disconnect sense & voltage should rise to approximately 15.5 volts and light come on. Reconnect sense.Connect black test lead to "C", voltage should drop to approximately 12.5 volts.Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for



IM286

IM294

A

A

24

12

28.7

14.6



1. POWER OFF:

2. POWER ON:




for



IM318 A 12 14.4



1. POWER OFF:

2. POWER ON:



Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for



IM850 A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect "C" terminal to tester, push Computer button and voltage will drop to approximately 12.5V. field lampstays on.Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for



IM232 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IM211 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IM381 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove white test lead and lamp comes on, voltage drops to 12.0 volts and field light stays on . Remove greentest lead from light and field light goes off.Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsNIPPONDENSO


IN209

IN210

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IN-01Product Group 3/26/1998176Page

for



IN234 A 12 14.3



1. POWER OFF:

2. POWER ON:




11/21/2014Revision: Date :IN-02Product Group177Page

for



IN229

IN229HD

A

A

12

12

14.1

14.1



1. POWER OFF:

2. POWER ON:



NOTE: When testing the Transpo IN229 or the Original Equipment voltage regulators, the short circuit light mayflash and the meter will indicate the set point voltage.


for



IN218

IN217

A

A

12

24

14.2

27.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "B+.". The meter should indicate approximately 17V on the IN218regulator and 28V on the IN236 regulator.


for



IN235 A 12 14.1



1. POWER OFF:

2. POWER ON:




for



IN231

IN232

A

A

12

12

14.4

14.3



1. POWER OFF:

2. POWER ON:




for



IN223 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove test lead from terminal marked "P" Indicator light should turn on, field lamp will remain on, and the meterwill indicate approximately 12.0V.


for



IN550 A 12 14.2



1. POWER OFF:

2. POWER ON:




for



IN551

IN558

IN560

IN562

B

B

B

B

12

12

12

12

14.3

14.3

14.3

14.3


IN822

IN579

B

B

12

12

14.3

14.3


1. POWER OFF:

2. POWER ON:



Remove black test lead from terminal marked "STA". Indicator light should turn on and the meter will indicate theset point voltage.


for



IN569

IN578

IN589

B

B

B

12

12

12

14.3

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove black test lead from terminal marked "STA". Indicator light should turn on and the meter will indicate theset point voltage.


for



IN233 A 24 28



1. POWER OFF:

2. POWER ON:




for



IN441 A 14 14.3



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked Stator. Indicator light will turn on and meter will indicate 12V; Fieldcircuit light stays on. Reconnect. Remove red test lead from terminal marked "IG"; field lamp should turn offmeter will indicate 12V.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.

NOTE on Stator: Transpo (White test lead) / OE (Red test lead)


for



IN442 A 12 14.1



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked stator. Indicator light will come on.


for



IN601 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN602 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove black test lead from terminal marked "STA". Indicator light turn on and the meter will indicator lightshould turn on and the meter will indicate the set point voltage.


for



IN567 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN8315 A 12 14.2



1. POWER OFF:

2. POWER ON:




for



IN554 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN228 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN230 A 12 14.1



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator light will come on and voltage will rise to approximately16 volts.

NOTE: When testing the Transpo IN230 or the Original Equipment voltage regulators, the short circuit light mayflash and the meter will indicate the set point voltage.


for



IN568 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN821 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove black test lead from the terminal marked "STA". The indicator light should turn on and the meter willindicate the set point voltage.


for



IN220

IN226

IN250

IN256

A

A

A

A

12

12

12

12

14.4

14.4

14.4

14.4


IN436

IN437

IN439

IN444

A

A

A

A

12

12

12

12

14.0

14.4

14.4

14.4


1. POWER OFF:

2. POWER ON:



Remove test lead from the terminal marked "*". The indicator light will turn on and the meter will indicateapproximately 12V and the field lamp will remain fully on (this is the soft start mode of the regulator).To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.



for



IN434

IN438

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:



Remove test lead from the terminal marked "*". The indicator light will turn on and the meter will indicateapproximately 12V and the field lamp will remain fully on (this is the soft start mode of the regulator).To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.



for



IN920 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove the white test lead from the terminal marked stator, the indicator light will turn on and the meter willindicate approximately 12V. The field lamp will remain fully on . (This is the soft -start mode of the regulator)

NOTE: Transpo (White test lead) / OE (Red test lead)


for



IN555 B 12 14.3



1. POWER OFF:

2. POWER ON:



Remove the white test lead from the terminal marked stator, The indicate approximately 12V. The field lamp willremain fully on, (This is the soft-start mode of the regulator.)


for



IN220E A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove test lead from the terminal marked "*". The indicator light will turn on and the meter will indicateapproximately 14.6v. and the field lamp will remain fully on.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.


for



IN450 A 12 14.4



1. POWER OFF:

2. POWER ON:




* NOTE: On OE Regulator connect a Red test lead to stator (STA)


for



IN445 A 12 14.5



1. POWER OFF:

2. POWER ON:



* With regulator ‘ON’, connect "C" terminal to tester, push Computer button on tester and Voltage should drop to12.5 volts.To check for over Voltage, push the "Over Voltage" button and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IN453 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white lead from stator and voltage should drop to 12.0V and 12V lamp should come on. Field circuitlamp stays on.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IN455 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S" and lamp turns on and voltage remains the same.


for



IN277 A 12 14.5



1. POWER OFF:

2. POWER ON:



Disconnect “Stator” terminal, “Light” comes on, voltage goes to 12 Volts and field light stays on. Remove “Light”terminal, Volts will read 12 Volts and field light will go off.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsPARIS RHONE


IP125

IP126

IP955

IP125NV

A

A

A

A

12

24

24

12

14.6

28.4

28.4

14.6



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IP-01Product Group 7/8/1998208Page

for



IP127 A 12 14.7



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IP-02Product Group209Page

for



IP135

IP135B

IP129B

A

A

A

12

12

24

14.3

14.3

27.5



1. POWER OFF:

2. POWER ON:




for



IP122

IP152

IP1639

IP1655

A

A

A

A

12

12

12

12

14.4

14.2

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove black test lead from the blue wire of the regulator . Indicator light should turn on and meter will stillindicate the set point voltage.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IP137

IP1903

IP2700

A

A

A

12

12

12

14.6

14.6

14.6



1. POWER OFF:

2. POWER ON:




for



IP735B

IP729B

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:




for



IP130 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from the stator wire of the regulator. indicator light should turn on and meter will stillindicate the set point voltage.


for



IP1926 A 12 14.6



1. POWER OFF:

2. POWER ON:




for



IP736 A 12 14.2



1. POWER OFF:

2. POWER ON:




for



IP123 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove black test lead from blue wire. Indicator light should turn on and voltage will remain the same.


for



IP1652 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from the blue wire of the regulator. Indicator light should turn on and meter will readapproximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsLADA


IR674 A 12 14.6



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IR-01Product Group219Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsSEV MARCHAL


IS219

IS219A

B

B

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IS-01Product Group220Page

for



IS222 B 12 14.3



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IS-02Product Group 10/27/1900221Page

for



IS301 B 12 14.2



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IS-03Product Group222Page

for



IS223 B 12 14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IS-04Product Group 10/27/1900223Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsMAGNETI-MARELLI


IX106

IX107

IX108

IX109

A

A

A

A

12

12

24

24

14.2

14.2

28.0

28.0



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IX-01Product Group 11/22/1900224Page

for



IX110

IX111

A

A

12

24

14.5

28.5



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IX-02Product Group225Page

for



IX4004 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



IX121 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from stator terminal. Indicator light will come on. Field light will stay on and meter willread approximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IX127

IX128

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from stator terminal . Indicator light will come on. Field light will stay on and meter willread approximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



IX123

IX123S-B64

A

A

12

12

14.1

14.1



1. POWER OFF:

2. POWER ON:



Remove white test lead from stator terminal. Indicator light will come on. Field light will stay on and meter willread approximately 12 volts.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.


for



IX118 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red lead from stator and voltage will remain the same. Field lamp will flicker and 12V lamp come on.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsMANDO


IY785

IY786

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IY-01Product Group231Page

for



IY510 A 12 14.5



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IY-02Product Group 3/9/1999232Page

for



IY422 A 12 14.5



1. POWER OFF:

2. POWER ON:



Disconnect sense (Red) lead, voltage should go to 15.5V.


for



IY058 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from "S" terminal. Voltage will go up to approximately 15.5V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsNIKKO


IZ226

IZ227

A

A

24

12

27.5

14.6



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :IZ-01Product Group235Page

for

TRANSPO TESTER INSTRUCTIONStype regulatorsLEECE NEVILLE


L79000

L79000HD

L79000HDP

L79000LH

A

A

A

A

12

12

12

12

14.2

14.2

14.2

14.2


L79000S

L79000X

L95019

L96852

A

A

A

A

12

12

12

24

14.2

14.2

14.2

27.5


1. POWER OFF:

2. POWER ON:



Remove red test lead from regulator wire marked "TRIO". Filed lamp should turn off and the meter will indicatelow voltage.

11/21/2014Revision: Date :L-01Product Group 10/30/1900236Page

for



L79350S

L97050S

A

A

24

32

27.5

37.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from regulator wire marked "TRIO". Filed lamp should turn off and the meter will indicatelow voltage.


for



L79000AC

L96345AC

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from regulator wire marked "Stator". Filed lamp should turn off and the meter will indicatelow voltage.

11/21/2014Revision: Date :L-03Product Group238Page

for



L95300S

L99500S

L99825S

L99850S

A

A

A

A

24

12

24

32

28.0

14.2

27.5

37.5



1. POWER OFF:

2. POWER ON:



NOTE: Connect B+ to the three stator Terminals if no IGN terminal is used


for



L77973AC

L97300AC

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from the regulator's stud marked "Stator". Field lamp should turn off and the meter willindicate low voltage.


for



L77973S

L78855S

L78935S

L97300S

A

A

A

A

12

24

32

12

14.2

27.5

37.5

14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from regulator's stud marked "TRIO" or "IGN". Field lamp should turn off and the meterwill indicate low voltage.


for



L5022

L5042

L5062

L5078

A

A

A

A

12

24

32

12

14.2

27.5

37.5

14.2


L5042HD A 24 27.5


1. POWER OFF:

2. POWER ON:




for



L5016

L5028

B

B

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



L5003 B 12 14.2



1. POWER OFF:

2. POWER ON:




for



L99920

L99920HD

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from “Stator” terminal and regulator turns off.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsMOTOROLA


M5-156A

M5-157A

M5-161A

M5-163A

B

B

B

B

12

24

24

24

14.2

29.2

28.4

28.0


M5-177A

M5-191A

M5-211A

M5-232A

B

B

B

B

24

12

12

12

28.0

14.2

14.2

14.4


1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :M5-02Product Group246Page

for



M5-239A

M5-274A

B

B

12

36

13.8

38.4



1. POWER OFF:

2. POWER ON:




for



M5-130A

M5-130

B

B

12

12

15.2

15.2



1. POWER OFF:

2. POWER ON:



NOTE: * Regulators with One (1) yellow wire: M5-30A, M5-42A, M5-130A, M5-135, M5-141A** Regulators with Two (2) yellow wires: M5-28A, M5-50A


for



M5-143A

M5-150A

M5-206A

M5-218A

B

B

B

B

12

12

12

12

14.2

14.2

15.3

15.3


M5-222A

M5-185A

B

B

12

24

15.3

29.2


1. POWER OFF:

2. POWER ON:



NOTE: * Regulators with One (1) Yellow wire: M5-143A, M5-150A, M5-206A, M5-218A, M5-222A, M5-185A


for



M5-137A

M5-142A

M5-184A

B

B

B

12

12

24

15.2

14.2

29.2



1. POWER OFF:

2. POWER ON:




for



M5-113A

M5-122A

M5-216A

B

B

B

12

12

12

14.2

14.4

14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from yellow wire of the regulator. Indicator light should turn on and the meter will indicatethe set point voltage.


for



M5-204A B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked with "*". Field lamp should still blink and the meter will indicateapproximately 15.3 v.


for



M5-228A

M5-138A

M5-174A

M5-205A

B

B

B

B

12

12

12

12

14.1

15.2

14.1

14.1


M5-223A B 12 13.8


1. POWER OFF:

2. POWER ON:




for



M5-230A B 12 14.1



1. POWER OFF:

2. POWER ON:




for



M5-196A B 12 14.2



1. POWER OFF:

2. POWER ON:




for



M5-159A

M5-227A

B

B

24

12

29.2

14.2



1. POWER OFF:

2. POWER ON:




for



M5-146

M5-146A

B

B

12

12

15.2

15.2



1. POWER OFF:

2. POWER ON:




for



M5-197A

M5-207A

M5-250A

B

B

B

12

12

12

15.0

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



M5-198A

M5-200A

M5-244A

B

B

B

12

12

12

15.0

14.2

13.3



1. POWER OFF:

2. POWER ON:




for



M5-200SA6

M5-200SA8

M5-200SA12

M5-200SA24

B

B

B

B

6

8

12

24

7.8

9.5

14.2

27.5


M5-200SA32 B 32 37.5


1. POWER OFF:

2. POWER ON:



Remove white test lead from the yellow wire of the regulator marked "Stator ". Field lamp should turn off and themeter will indicate low voltage. On regulators with indicator light, light should also turn on when stator is removedfrom the regulator.

* NOTE: Not used on 24V & 32V Regulators


for



M5-226A A 12 14.4



1. POWER OFF:

2. POWER ON:




for



M5-208A

M5-209A

B

B

24

24

29.2

28.0



1. POWER OFF:

2. POWER ON:



Measure between regulator's yellow and red wire using an ohm meter (without a connection to the voltageregulator tester). Approximately 150 Ohms must be measured.


for



M5-225A

M5-225

A

A

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :M5-24Product Group 7/29/1997263Page

for



M5-217A B 12 14.2



1. POWER OFF:

2. POWER ON:




for



M5-203A B 12 14.2



1. POWER OFF:

2. POWER ON:




for



M5-233A B 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from yellow wire of the regulator marked as "Stator". Field lamp should turn off and themeter will indicate low voltage.


for



M5-224A

M5-245A

B

B

12

12

14.4

13.8



1. POWER OFF:

2. POWER ON:





for



M5-181A

M5-192A

M5-201A

B

B

B

12

12

12

15.0

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



M5-172A

M5-169A

B

B

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:




for



M5-149A B 24 28.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". field lamp should still blink and the meter will indicateapproximately 29.5v.


for



M5-215A A 12 14.4



1. POWER OFF:

2. POWER ON:




for



M5-193A

M5-214A

M5-240A

B

B

B

12

12

12

14.4

14.4

14.4



1. POWER OFF:

2. POWER ON:




for



M5-237A B 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from stator wires. The field lamp should stay on and the meter will indicate high voltage.Connect red test lead to the post marked "no connection". Regulator will regulate at the specified set pointvoltage.


for



M5-292A A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator". Field lamp should turn off and the meter will indicateapproximately 12v.


for



M5-329A A 12 14.2



1. POWER OFF:

2. POWER ON:




for



M5-247A B 24 27.6



1. POWER OFF:

2. POWER ON:




NOTE: Original Equipment Regulator no. 5-247 is an "A" circuit compared to Transpo's "B" circuit.


for



M5-249A B 24 28.0



1. POWER OFF:

2. POWER ON:




NOTE: Original Equipment Regulator no. 5-249 is an "A" circuit compared to Transpo's "B" circuit.


for



M5-050A A 12 14.5



1. POWER OFF:

2. POWER ON:





for



M5-280A A 12 14.2



1. POWER OFF:

2. POWER ON:





for



M5-29A

M5-48A

M5-63A

M5-151A

B

B

B

B

12

24

24

12

15.0

29.2

29.2

15.0


M5-152A

M5-182A

M5-242(A)

M5-248A

B

B

B

B

12

24

12

24

14.2

29.2

14.2

28.4


1. POWER OFF:

2. POWER ON:




for



M5-151SA6

M5-151SA8

M5-151SA12

M5-151SA24

B

B

B

B

6

8

12

24

7.8

9.6

14.2

27.5


M5-151SA32 B 32 37.5


1. POWER OFF:

2. POWER ON:



Remove the white test lead from the yellow wire of the regulator marked "stator". Field lamp should turn off andthe meter will indicate low voltage. On models with indicator light connection, removal of stator lead formregulator should cause the light to turn on and meter indicates low voltage.

NOTE * Not used for 24V and 32V


for



M5-26A

M5-27A

M5-92A

M5-93A

B

B

B

B

12

24

12

24

15.2

29.2

15.2

29.2


M5-153A

M5-183A

B

B

12

24

15.0

29.2


1. POWER OFF:

2. POWER ON:




for



M5-104A

M5-121A

M5-179A

A

A

A

12

12

24

14.2

14.2

28.4



1. POWER OFF:

2. POWER ON:



NOTE:The above are "SCR" type regulators. They cannot be tested on Transpo's regulator tester due to a requirementof an adapter. To test them simply install them in the appropriate alternator and check for regulation.


for



M5-164A

M5-167A

B

B

24

12

28.4

14.2



1. POWER OFF:

2. POWER ON:




for



M5-265

M5-266

M5-269

M5-270

A

A

A

A

12

12

24

24

14.4

14.4

28.4

28.4



1. POWER OFF:

2. POWER ON:




for



M5-123A

M5-128A

M5-234A

A

B

B

24

32

12

28.0

38.4

14.2



1. POWER OFF:

2. POWER ON:




for



M5-158A

M5-162A

M5-166A

B

B

B

24

24

24

29.2

28.4

28.4



1. POWER OFF:

2. POWER ON:




for



M5-160A B 24 29.1



1. POWER OFF:

2. POWER ON:



REGULATOR CONNECTION TEST LEAD FUNCTIONBLACK BLACK BATTERY NEGATIVERED RED TRIO, IGNITION, AUXGREEN YELLOW FIELDYELLOW NO CONNECTION


for



M5-165A B 12 14.4



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsVALEO / MOTOROLA


M5-508 B 12 14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :M-01Product Group 10/20/1997290Page

for



M5-509 B 12 14.1



1. POWER OFF:

2. POWER ON:




for



M5-515 B 12 14.5



1. POWER OFF:

2. POWER ON:



Remove black test lead from terminal marked "D+". Indicator will come on.


for



M5-170A

M5-742A

B

B

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :M-04Product Group293Page

for



M5-762 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



M5-180A

M5-241A

M5-763A

M5-764A

B

B

B

B

12

12

12

12

14.2

14.2

14.1

14.2



1. POWER OFF:

2. POWER ON:




for



M5-768 B 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "D+". Indicator light will come on.


for



M506

M508

A

A

12

12

14.1

15.0



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



M507 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



M509

M510

A

A

12

12

14.4

14.4



1. POWER OFF:

2. POWER ON:




for



M511 A 14 14.5



1. POWER OFF:

2. POWER ON:




for



M512 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove white lead from stator and voltage should drop to 12.0v. lamp should come on. Field circuit lamp stayson.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



M513 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove white lead from stator and voltage should drop to 12.0v and 12V lamp should come on. Field circuit lampstays on.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V.


for



M5-036 B 12 14.4



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsNIEHOFF


NA2-101

NA2-102

NA2-103

A

A

A

24

12

32

27.5

14.2

37.5



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :N-01Product Group304Page

for



N9013

N9015

A

A

12

24

14.3

27.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from blue wire of the regulator. Field lamp should turn off and the meter will indicate lowvoltage.

11/21/2014Revision: Date :N-02Product Group 5/1/1997305Page

for



N9014 A 12 14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from blue wire of the regulator. Field lamp should turn off and the meter will indicate lowvoltage and indicator light will turn on.


for



NA2-111

NA2-110

A

A

24

12

28.0

14.0



1. POWER OFF:

2. POWER ON:



Remove red test lead from the terminal marked "IGNITION". Field lamp should turn off and the meter will indicateapproximately 12V. For NA2-111. For NA2-110.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsMAGNETON-PAL


MP293

MP291

A

A

14

12

28.4

14.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :PAL-01Product Group 8/22/1902308Page

for



MP417 B 12 14.3



1. POWER OFF:

2. POWER ON:




for



MP419 B 12 14.3



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsPRESTOLITE


P8-328

P8-328A

P8-379

P8-379A

B

B

B

B

12

12

12

12

14.2

14.2

15.0

15.0


P8-407

P8-407A

P8-406

P8-406A

B

B

B

B

12

12

12

12

15.0

15.0

15.0

15.0


1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :P8-01Product Group 5/1/1997311Page

for



P8-403

P8-403A

P8-404

P8-404A

B

B

B

B

12

12

12

12

14.2

14.2

14.2

14.2


P8-410

P8-410A

P8-343

P8-343A

B

B

B

B

12

12

12

12

14.2

14.2

15.0

15.0


1. POWER OFF:

2. POWER ON:




for



P8-354

P8-354A

P8-355

P8-355A

B

B

B

B

12

12

12

12

14.2

14.2

14.2

14.2


P8-357

P8-357A

P8-352

P8-352A

B

B

B

B

12

12

12

12

14.2

14.2

14.2

14.2


1. POWER OFF:

2. POWER ON:




for



P8-368

P8-368A

P8-405

P8-405A

B

B

B

B

12

12

12

12

15.0

15.0

14.2

14.2


P8-393

P8-393A

B

B

24

24

27.5

27.5


1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsTE REPAIR CIRCUIT


TRI100

TRI110

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :TRI-01Product Group315Page

for



TRI400R

TRI400S

TRI405

TRI406

A

A

A

A

12

12

12

12

14.5

14.5

14.4

14.4


TRI410

TRI420

TRI421

A

A

A

12

12

12

14.6

14.6

14.6


1. POWER OFF:

2. POWER ON:



TESTER CONNECTION CHART B ... RED TEST RED (B+) S ... RED TEST LEAD (SENSE)R ... RED TEST LEAD (IG) T ... RES TEST LEAD (TRIO) F ... YELLOW TEST LEAD (FLD)L ... RED TEST LEAD (INDICATOR LIGHT) E ... BLACK TEST LEAD (GROUND)

NOTE: Regulators shown with circuit up (Epoxy side)NOTE: After repair circuit installation, refer to complete regulator assembly procedure.

REFER TO PRODUCT GROUP TRI-04, PAGE 376-A, FOR REGULATOR'S DIAGRAM

11/21/2014Revision: Date :TRI-02Product Group 6/2/1905316Page

for



TRI422

TRI430

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:



TESTER CONNECTION CHART B ... RED TEST RED (B+) S ... RED TEST LEAD (SENSE)R ... RED TEST LEAD (IG) T ... RED TEST LEAD (TRIO) F ... YELLOW TEST LEAD (FLD)L ... RED TEST LEAD (INDICATOR LIGHT) E ... BLACK TEST LEAD (GROUND)




for



TRI219

TRI220

TRI221

TRI222

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


TRI224

TRI225

TRI226

TRI227

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


1. POWER OFF:

2. POWER ON:



Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.




for



TRI250

TRI251

TRI252

TRI253

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


TRI254

TRI255

A

A

12

12

14.5

14.5


1. POWER OFF:

2. POWER ON:



Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.




for



TRI10DN B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove white test lead from regulator's connection marked "STA". Field lamp should turn off and the meter willindicate 12V.


for



TRI268

TRI270

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



TESTER CONNECTION CHART NOTE: This instruction does not apply to TRI270B ... RED TEST RED (B+) I ... GREEN TEST LEAD (I.L.) T ... RED TEST LEAD (TRIO)E ... BLACK TEST LEAD (B-) F ... YELLOW TEST LEAD (FLD) A ... RED TEST LEAD (SENSE)Remove the red test lead from the wire marked "sense". The field light will still blink, the meter will indicate from15v to 16v and the indicator lamp will remain on.

NOTE: Instruction #3 Does not apply to TRI270


for



TRI247 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from wire marked "STA". Indicator light should turn on, field lamp will remain on and themeter will indicate 12V. Remove red test lead from wire marked "IG". Field lamp should turn off.Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V.


for



TRI248 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



TRI275

TRI285

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



TRI278 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove red test lead from the wire marked as "S". Field lamp should still blink and the meter will indicateapproximately 15.5V.


for



TRI233 A 24 27.5



1. POWER OFF:

2. POWER ON:




for



TRI267 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove red test lead from the wire marked as "C" and connect a black test lead to the "C" terminal. Field lampshould still blink and the meter will indicate approximately 12.5v.


for



TRI839

TRI273

TRI835

A

A

A

12

12

12

14.4

14.4

14.4



1. POWER OFF:

2. POWER ON:



1. Remove red test lead from terminal marked "TRIO". Field lamp should still blink, the meter will indicate the setpoint voltage and the indicator light will turn on.2. Reconnect red test to "TRIO". Connector a black test lead to terminal marked "C". Field lamp should still blinkand the meter will indicate approximately 12.5v.


for



TRI423 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "TRIO". Field lamp should still blink and the meter will indicateapproximately 15.5v.


for



TRI271

TRI276

TRI836

TRI837

A

A

A

A

12

12

12

12

14.5

14.4

14.4

14.4



1. POWER OFF:

2. POWER ON:



Remove the red test lead from the wire marked as "SENSE". The field light will still blink the meter will indicatefrom 15V. to 16V, and the indicator lamp will remain on.Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V.


for



TRI257 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white lead from terminal marked "stator". The indicator light will turn on and the meter will indicateapproximately 12 volts and the field lamp will remain fully on.Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.


for



TRI232 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



F8512

F8512M

F8512S

B

B

B

12

12

12

14.2

14.3

14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Indicator light should turn on meter will still indicate set pointvoltage. Removal of test lead from "S" and "I" terminal will result in the field lamp turning off and the meterreading 12v. On mechanical type on due to the regulator's internal circuitry. Limit this test to a short time.


for



IM284 A 12 14.4



1. POWER OFF:

2. POWER ON:





for



IN449

IN440

A

A

12

12

14.5

14.0



1. POWER OFF:

2. POWER ON:



Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V.


for



L1666280 A 12 13.8



1. POWER OFF:

2. POWER ON:




for



IM345 A 12 14.3



1. POWER OFF:

2. POWER ON:



Caution - Note:• Connect DRIVER to tester “PD”• IM345 has D-P terminal functions: D=Drive, P=Phase.• D-P Type Regulators are immediately damaged if tested using procedure typical to common S-L typeregulators, where B+ Voltage would be applied to the D terminal position.


for



IH758 A 12 14.4



1. POWER OFF:

2. POWER ON:



Caution - Note:• IH758 has D-P terminal functions: D=Drive, P=Phase.• D-P Type Regulators are immediately damaged if tested using procedure typical to common S-L typeregulators, where B+ Voltage would be applied to the D terminal position.


for



IB392BG A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "STA". Field lamp remain fully on and the meter will indicateapproximately 12V. Reconnect the white test lead. Remove red test lead from the terminal marked "S", field lampwill turn off, the indicator light will turn on and the meter will indicate 12V.Using VRC2010: To check for over Voltage, push the “Over Voltage” switch and the “Lamp Indicator” will turn onbetween 16.0V and 17.1V.

NOTE: Connect B- (black) test lead last, already having turned on the tester "ON" switch.• 20 ampere 60 volt field transistor voltage saturation test @ 5 amps 13.50 volts = 150 to 250 milli-volts• Undervoltage Lamp Indication = 8.50 volts to 10.00 volts• Overvoltage Lamp Indication = 16.00 volts to 17.10 volts• Current Leakage = 2.0 milli-amps


for



D3101 B 12 14.2



1. POWER OFF:

2. POWER ON:



Remove WHITE TEST LEAD from terminal marked "STATOR", 12 volt Lamp will turn on and Field light will turnoff.


for



IH258 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IH769 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white lead from stator; 12 volt lamp will come on and voltage will read 12.0 volts. Field lamp will be on.



for



IM843 A 24 28.5



1. POWER OFF:

2. POWER ON:




for



IM369 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator" field and lamp light comes on. Remove green test leadfrom terminal marked "Light" field and lamp light goes off.

Using VRC2010: Connect external 3 Watt Lamp from Tester Battery Positive to the Voltage Regulator lampconnection. Do not use the VRC2010 Lamp connection.


for



IM851 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked "Stator" field and lamp light comes on and voltage will indicate 12 volts.Remove green test lead from terminal marked "Lamp" and lamp light goes off. Remove red test lead from terminal marked"Ignition" and field light goes off.* Connect black lead to "C" computer terminal and field lamp will stay on and voltage will read approximately 12.7 voltsUsing VRC2010: Push the choke drive switch and the "Choke Drive Indicator Lamp" will turn on between 16.0V and 17.1V.


for



D432 B 12 14.7



1. POWER OFF:

2. POWER ON:



Remove the white test lead from terminal marked "STATOR". The indicator light will turn on, field lamp will stay on and meterwill indicate approximately 12V. Disconnect the test lead from "L" terminal. Regulator will turn off and the meter will indicate12V.Using VRC2010: To check for over Voltage, push the “Over Voltage” switch and the “Lamp Indicator” will turn on between16.0V and 17.1V. Push the choke drive and the “Choke Drive Indicator Lamp” will turn on, if present.


for



IN219

IN221

IN222

IN224

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


IN225

IN227

IN251

IN252

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


1. POWER OFF:

2. POWER ON:





for



IN253

IN254

IN255

IN429

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


IN431

IN435

IN254CN

IN255CN

A

A

A

A

12

12

12

12

14.5

14.5

14.5

14.5


1. POWER OFF:

2. POWER ON:





for



IM757 A 12 14.70



1. POWER OFF:

2. POWER ON:




for



IH744 A 12.0 14.4



1. POWER OFF:

2. POWER ON:



Remove sense lead and voltage rises to approximately 15.5 volts, reconnect sense lead. Remove white test leadfrom stator, 12 volt lamp comes on, voltage drops to 12 volts and field LED stays on (soft start).



for



IH738 A 12 14.5



1. POWER OFF:

2. POWER ON:






for



D404 A 12 14.6



1. POWER OFF:

2. POWER ON:




for



IM848 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove sense lead and voltage rises to approximately 15.4 volts, reconnect sense lead. Remove white test leadfrom stator, 12 volt lamp comes on, voltage drops to 12 volts and field LED stays on (soft start). Remove Lightlead field light and Lamp light turn off.


for



M519 B 12 14.5



1. POWER OFF:

2. POWER ON:



Remove “White” lead from “Stator”, meter will read 12.0 volts field light will come on and 12 volt lamp will comeon. Remove “Lamp” terminal and field light will go out and lamp light will go out.


for



IH774 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove white lead from stator, field circuit lamp will stay on. 12V lamp will come on and voltage will drop to 12V.



for



IH742 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove sense lead and voltage rises to approximately 15.5 volts, reconnect sense lead. Remove white test leadfrom stator, voltage remains the same and lamp comes on.

Using VRC2010:To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V.


for



IM350 A 12 14.4



1. POWER OFF:

2. POWER ON:






for



IM341 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove sense lead and voltage rises to approximately 15.4 volts, reconnect sense lead. Connect C terminal ofregulator to C terminal on tester, and press Computer button, Voltage drops to 13.1 volts. Remove white test leadfrom stator, 12 volt lamp comes on, voltage drops to 12 volts and field LED stays on (soft start). Remove Lightlead field light and Lamp light turn off.


for



IN215

IN452

A

A

12

12

14.6

14.5



1. POWER OFF:

2. POWER ON:



Connect C terminal of regulator to C terminal on tester, and press Computer button, Voltage will read 12.6V.Remove white test lead to confirm charge indicator light function.To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn on between 16.0Vand 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.IN452 - No connection on black test lead labeled “C” on IN215, “D” on IN452.


for



IM358 A 12 14.4



1. POWER OFF:

2. POWER ON:



No additional test required.


for



D751 A 12 15.1



1. POWER OFF:

2. POWER ON:



IMPORTANT ... Tester FIELD LOAD Switch Must Be Set to 0.5 AMP !

Remove "White" test lead from terminal marked "Stator". The indicator light will turn on, field lamp will stay on andthe meter will indicate approximately 12 volts. Remove red test lead from Sense and light will come on. Remove"Green" test lead, lamp will go off and field lamp will go off.

IMPORTANT ... Tester FIELD LOAD Switch Must Be Set to 0.5 AMP !


for



IM853 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove white test lead from terminal marked “Stator” field, lamp light comes on and Voltage will incate 12 Volts.Remove green test lead from terminal marked “Lamp” and lamp light goes off. Remove red test lead fromterminal marked “Ignition” and the field light goes off.


for



D10SE132

D10SE138

A

A

12

12

14.8

14.8



1. POWER OFF:

2. POWER ON:




for



IY903 A 12 14.2



1. POWER OFF:

2. POWER ON:



Remove red test lead from "S" terminal. Voltage will go up to approximately 15.5V.


for



IM465 A 12 14.3



1. POWER OFF:

2. POWER ON:



• IM465 has D-P terminal functions: D=Drive, P=Phase.• D-P Type Regulators are immediately damaged if tested using procedure typical to common S-L typeregulators, where B+ Voltage would be applied to the D terminal position.

• IM465 field brush is top / outer brush; (unlike many other Mitsubishi regulators).


for



F797

F797HD

A

A

12

12

*14.0

*14.0



1. POWER OFF:

2. POWER ON:



Connect RC terminal of regulator to RCV regulator on tester. Connect LI terminal of regulator to LI terminal on tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 14.0V Set Point indicated above is the 'default VSet' (no vehicle PCM input).


for



F601

F601HD

A

A

12

12

14.0*

14.0*



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 14.0V Set Point indicate above is the 'default VSet' (no vehicle PCM input).

• AS-RC-LI Terminals• Regulation Voltage Controlled by Vehicle PCM


for



IX131

IX131HD

A

A

12

12

*14.0

*14.0



1. POWER OFF:

2. POWER ON:



Connect RC terminal of regulator to RCV terminal on tester. Connect LI terminal of regulator to LI terminal on tester1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 14.0V Set Point indicated above is the 'default VSet' (no vehicle PCM input).


for



M5-251 A 24 26.5



1. POWER OFF:

2. POWER ON:



DO NOT CONNECT BOTH SENSE LEADS AT THE SAME TIME.

• VSET1: Disconnect Sense (Purple Lead Wire) ... Voltage Regulation 28.00V +/- 0.5V

• VSET2: Connect Regulator as shown; Use Resistor 5K Ohm... Voltage Regulation 26.5V +/- 0.5V

NOTE: THE VOLTAGE IS BELOW METER RANGE WITHOUT USING A RESISTOR ON YELLOW WIRE.REGULATOR IS FACTORY SET AT 26.5V. WE DO NOT RECOMMEND TURNING VARIABLERESISTOR UNTIL INSTALLED ON VEHICLE.


for



TRI845 A 12 14.4



1. POWER OFF:

2. POWER ON:



Connect Computer (C) to Black (B-), voltage will read 12.5 voltsRemove Sense (Red), Lamp light will turn on.

* Connect only for Computer (C) function test


for



IM846 A 24 28.4



1. POWER OFF:

2. POWER ON:




for



M517 B 12 14.4



1. POWER OFF:

2. POWER ON:



Remove “White” lead from “Stator”, meter will read 12.0 volts field light will come on and 12 volt lamp will comeon. Remove “Lamp” terminal and field light will go out and lamp light will go out.


for



IB251 A 12 14.4



1. POWER OFF:

2. POWER ON:



Power On: Field light should blink and meter will indicate approximately the set point voltage indicated in the above table.Remove white test lead from terminal marked "Stator" field light and "Lamp" light will come on and voltage will show 12 volts.Reconnect "Stator" wire;Remove green test lead from "Light" terminal, field light will continue to blink and meter will indicateapproximately the set point voltage indicated in the above table. Reconnect "Lamp" wire;Remove ignition, field light willcontinue to blink, "Lamp" light will turn on and meter will indicate approximately the set point voltage indicated in the abovetable.


for



DE604

DE605

DE609

A

A

A

12

12

12

14.8

14.8

14.8



1. POWER OFF:

2. POWER ON:




for



DE708 B 12 14.8



1. POWER OFF:

2. POWER ON:



Remove "White" test lead from "Stator" lamp will come on and voltage will go to 12 volts.Reconnect "White" test Lead.Remove "Green" Lead from "Light" terminal regulator will go to 12 volts and "Field" light will stop blinking.


for



IB229 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove White Test lead from Stator Terminal, Lamp will come on, display will show 12 volts and field light willstay on. Remove Green Test lead and field light will turn off.


for



IB235 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove White Test Lead from Stator, Lamp Light comes on and Field Light stay on.Remove Green Test Lead from Light terminal, Lamp Light and Field Light turn off.

The voltage will drop when remove the stator lead.


for



M5-61A

M5-74A

M5-79A

M5-94A

B

B

B

B

24

32

12

32

28.0

39.2

14.2

38.4


M5-136A

M5-147A

M5-148A

M5-154A

B

B

B

B

12

12

24

12

14.2

15.00

28.0

14.2


1. POWER OFF:

2. POWER ON:




for



IB298 B 24 28.3



1. POWER OFF:

2. POWER ON:



Remove White test Lead from Stator Light comes on. Reconnect Stator.Remove Green test Lead from Lamp, voltage remains same. Reconnect Light.Remove White test Lead from Stator, Light and Ignition voltage goes to 24 volts.

• Note: IB298 without Loss of Sense Lamp Indication• W-L-15-S-DFM Terminals • OE Compliant Circuit Protection & Functions... 'With Stator Start,


for

TRANSPO TESTER INSTRUCTIONStype regulatorsSAWAFUJI


IW700

IW701

A

A

24

12

28.5

14.2



1. POWER OFF:

2. POWER ON:



Remove test lead from Stator terminal and light will come on; reconnect test lead to Stator terminal. Remove testlead from Ignition terminal, field light will stop flashing and voltage goes to default. (see note)

Note: Remove test lead from Ignition terminal, field light will stop flashing and voltage goes to 12V for (IW701)and 24V (IW700).

11/21/2014Revision: Date :IW-01Product Group 10/29/1907380Page

for



M515 B 12 14.8



1. POWER OFF:

2. POWER ON:




for



IM529 A 12 *14.0



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing, Connect RC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 14.0V Set Point indicate above is the 'default VSet' (no vehicle PCM input).


for



D3587 B 12 13.8*



1. POWER OFF:

2. POWER ON:



Connect RVC terminal of D3587 to RCV terminal on tester. Connect FR terminal of D3587 to LI terminal ontester.2. Adjust Comm Voltage switch to position 13, Setpoint is 11.8V.3. Adjust Comm Voltage switch to position 14, Setpoint is 13.3V.4. Adjust Comm Voltage switch to position 15, Setpoint is 14.7V.

• This is GM RCV type, ‘Regulated Voltage Control’ system regulator.• Regulated Voltage Control is provided by the vehicle’s PCM / ECU or GBCM (Generator Battery ControlModule) via a digital ‘PWM’ signal applied to the regulator L-terminal.

11/21/2014Revision: Date :Product Group383Page

for



IN369 A 12 14.3



1. POWER OFF:

2. POWER ON:



The FR terminal is not connected.Disconnect the Sense terminal, the light should be ON, and the set point will read approximately 14.5 volts.Push the Over Voltage button, the set point should read approximately 17.3 volts.


for



IN317 A 12 14.35



1. POWER OFF:

2. POWER ON:



No connection to the FM Out terminal.Push Over Voltage button, Light should turn ON, set point is approximately 17.2 volts.Push Choke button, Choke Light should turn ON.


for



IM545 A 12 14.4



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Disconnect the Stator terminal and the Light should turn ON.Reconnect the Stator terminal, push the Over Voltage button, the light should turn ON, the set point will beapproximately 17.2 volts.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsVALEO MOTOROLA


M526 B 12 14.8



1. POWER OFF:

2. POWER ON:



After applying power part requires about 10 seconds to start regulating.Must install a 1.5uF capacitor betweenStator terminal #2 and B-. Attach VRC2010 Stator lead to Stator terminal #1.Disconnect Sense lead and light turns ON.Push Choke button, choke light will turn ON.Reconnect Sense lead and push Over Voltage button, light should turn ON, set point is approximately 17.3 volts.


for



IB206 A 12 14.5



1. POWER OFF:

2. POWER ON:



Do not connect FR terminal.Push Choke button and Choke light should be ON.


for



IM476 A 12 14.6



1. POWER OFF:

2. POWER ON:



Disconnect Sense lead and Light should turn ON. Set Point will be approximately 15.6 volts.Reconnect the Sense lead and press the Over Voltage button. The light should be ON, and the set point will beapproximately 17.3 volts.


for



IN258 A 12 14.4



1. POWER OFF:

2. POWER ON:



• When Ignition wire is disconnected from the regulator, VSet reading drops to default 12V.• When both the Field and Stator connections are disconnected from regulator, lamp illuminates.

Note: This regulator’s light circuit functions when a combined condition exists ... Loss of the Stator signal and B+Voltage drops below 14.0V (approx).

• IN258 is an "A" circuit, low side drive regulator.• D-IG-L Terminals (D = dummy / no function)• VSet 14.4V (+/- 0.2V).• Field rating 5-Amps.• Ignition activated.


for



in257 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove test lead from the terminal marked "*". The indicator light will turn on and the meter will indicateapproximately 12V and the field lamp will remain fully on (this is the soft start mode of the regulator).Using VRC2010: To check for over Voltage, push the "Over Voltage" switch and the "Lamp Indicator" will turn onbetween 16.0V and 17.1V. Push the choke drive and the "Choke Drive Indicator Lamp" will turn on, if present.

NOTE on Stator: Transpo (White test lead) / OE (Red test lead)REFER TO PRODUCT GROUP IN-29, PAGE 341-A FOR REGULATOR'S DIAGRAM


for



IB558 B 24 25.5



1. POWER OFF:

2. POWER ON:



Power On: Note Set Point on VRC2010 digital display;Disconnect Sense terminal and note set point readingshould rise to approximately 28.5 volts.


for



IN6002 B 12 14.2



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.• Disconnect the Sense Lead and verify Light Turns On.• No over voltage lamp

• S-IG-L Terminals• Ignition Activated• Without LRC• Standard Lamp – No Output


for



IN6001 B 12 14.2



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.• Disconnect the Sense Lead and verify Light Turns On.

• S-IG-L Terminals• Ignition Activated.• Without LRC• Active Lamp – With Output


for



IN6301

IN6301CN

B

B

12

12

14.1

14.4



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.

• IG-S-L-M(FR) Terminals• Ignition Activated• LRC 6-Seconds, Full Range• Multi-Step TempCo• Standard Lamp – No Output


for



IN6335 B 12 14.5



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only• Connect the C Terminal to B-, the set point should drop to 12.7 Volts• Remove Stator wire and the Light should turn ON

• IG-C-L-FR Terminals• Ignition Activated• LRC 11-Seconds (to 400HZ)• Standard Lamp – No Output• Due to the long delay, automatic spin bench testers should be setup to be in the ‘Wait Always’ mode. Not doingso may result in an inaccurate performance reading.


for



IX110CN A 12 14.2



1. POWER OFF:

2. POWER ON:




for



M3118C

M3118

A

A

24

24

28.5

28.0



1. POWER OFF:

2. POWER ON:




for



IB236 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove White Test Lead from Stator, Lamp Light comes on and Field Light stay on.Remove Green Test Lead from Light terminal, Lamp Light and Field Light turn off.

•IG-S-L-DFM Terminals • With LRC 5-Seconds • External Sense(EXTS) • Ignition Activated but will Lamp Activateand Stator Start • Active Lamp Function -With Output • Field, Lamp, Choke Short Circuit Protection

11/21/2014Revision: Date :IB-Product Group 3/6/2009399Page

for



IN6004 B 12 14.5



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only* Connect C terminal to B-, verify Set-Point is 12.8 V +/- 0.2V

• IG-C-L-FR Terminals• Standard Lamp Function - No Output• No Output LRC


for



IN6302 B 12 14.1



1. POWER OFF:

2. POWER ON:



1.Set Field Load Switch to 0.5 Amp only.2.This regulator is not tested for Over Voltage Lamp or Loss of Sense3.The RLO Function is similar to the RC control function found in PCM controlled Ford 6G systems and GM RVCsystems.When the vehicl ECM takes command of the regulator’s RLO circuit,the alternator Voltage follows the PWM signalduty cycle;the regulation Voltage will range between 11.80V and 14.99V as needed

• IG-RLO-L-M Terminals• Ignition Activated• LRC 6-Seconds, Full Range• Multi-Step TempCo (unless in RLO mode)


for



D4476 B 24 28.0



1. POWER OFF:

2. POWER ON:



Disconnect Sense Lead, verify the setpoint is 28.0+/-0.2v, also verify the the Light is on.Disconnect Stator Lead, verify the Light is on and the part stops function.Push the OVER VOLTAGE button and verify the Light is on.

D4476 is Stator Activated.Load AMP switch is 0.5 position only.


for



D4152 B 12 14.2



1. POWER OFF:

2. POWER ON:



Disconnect Sense Lead and verify the setpoint is 14.2+/-0.2v.Disconnect Stator Lead and verify the Light is on.Push the OVER VOLTAGE button and verify the Light is on.

D4152 is Stator Activated.Load AMP switch is 0.5 position only.


for



IB520 A 12 14.1



1. POWER OFF:

2. POWER ON:



Disconnect Stator Lead and verify the Light is on.Push the CHOKE DRIVE button and verify the CHOKE DRIVE lamp is on.

IB520 is Stator Activated.Load AMP switch is 0.5 position only.


for



IY028 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IM854 A 12 14.5



1. POWER OFF:

2. POWER ON:



Disconnecting Sense turns light on.


for



D840 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the part stops regulating and the voltage goes down to 12.0v.


for



IN6322 B 12 14.1



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.• No Over Voltage Lamp• No RLO terminal test default voltage test only

• IG-RLO-L-M Terminals• Ignition Activated• LRC 6-Seconds, Full Range• Multi-Step TempCo (unless in RLO mode)


for



IN6304 B 12 14.1



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.• Disconnect the Sense Lead and verify Light Turns On (slight delay), reconnect Sense Lead.• Disconnect Ignition Lead, voltage goes to 12 volts, Field Light turns off and Lamp Light turns off.



for



IN6003 B 12 15.0V



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only• Disconnect the Sense Lead and verify Light Turns On with Delay• This Regulator without Over Voltage Lamp Indication

• S-F-L Terminals• Stator Activated.• LRC 9-Seconds (to 400HZ)• Standard Lamp – No Output


for



IN6009 B 12 14.8



1. POWER OFF:

2. POWER ON:



• Set Load Amperage Switch to 0.5 Position Only• No over voltage lamp• Regulator without Over Voltage Lamp Indication

• F-L Terminals• Lamp Activated.• LRC 2-Seconds (to 400HZ)• Standard Lamp Function – No Output


for



IN6304 B 12 14.1



1. POWER OFF:

2. POWER ON:



• Set Field Load Switch to 0.5 Amp only.• Disconnect the Sense Lead and verify Light Turns On

... Need to verify all !!!!



for



IB314

IB696

B

B

12

12

13.8*

13.8*



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 11.8V.2. Adjust Comm Voltage switch to position 14, Setpoint is 13.3V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.4V.Note: The Voltages listed above are approximate and may not exactly match your meter read out.

• This is an RVC type, ‘Regulated Voltage Control’ system regulator.• Regulated Voltage Control is provided by the vehicle’s PCM / ECU or GBCM (Generator Battery ControlModule) via a digital ‘PWM’ signal applied to the regulator L-terminal.


for



IB231 A 12 14.5



1. POWER OFF:

2. POWER ON:



VRC2010 Tests:• To check for presence of Active Lamp function - Press ‘Choke Drive’ button, choke lamp will illuminate• To check for presence of Over Voltage function - Press ‘Over Voltage’ button, indicator lamp will illuminate

IB231• With LRC and Soft Start• L (D+) Terminal M5


for

TRANSPO TESTER INSTRUCTIONStype regulators


D907 B 12 14.0



1. POWER OFF:

2. POWER ON:



Disconnect Stator Lead and verify the Light is on.

B-Circuit, Volt Set 14.0V• S-F-L-P Terminals• Stator Activated• Full Short Circuit Protection• Excellent Choice for 1-Wire System


for



M523 B 12 14.3



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ

• Terminal Designation 16E-15 (Lamp-Ignition) • Stator Activated • LRC 5-Seconds • OE Compliant SoftStart • Lamp-Choke, Field Short Circuit Protection


for



IB286 B 12 14.4



1. POWER OFF:

2. POWER ON:



• To check for presence of Active Lamp function - Press ‘Choke Drive’ button, choke lamp will illuminate

• L-DFM Terminals • LRC 2.5 Seconds, w/ Soft Start • Active Lamp Function – With OutputNOTE: VRC101-34 adapter shown for enhance stator signal, not all late model regulators need enhance signal


for



IB261

IB261S-B40

B

B

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.• Push the Choke switch and the "Choke Drive" will turn on.• Remove white test lead from terminal marked "Stator" - the Lamp will come on and

Voltage will show 12 volts.• Remove green test lead from "light" terminal, field light will go out and voltage stays at 12 volts.

• L-FR Terminals • Stator Activated• With Soft Start & LRC• TC -10mV/C• Active Lamp Circuit -With Output


for



IB201 A 12 14.4



1. POWER OFF:

2. POWER ON:



1 Remove white test lead from terminal marked "Stator" - the Field light and Lamp will come on andVoltage will show 12 volts.

2 Remove green test lead from "light" terminal , field light will go out and voltage stays at 12 volts.3 No Over Voltage and Lamp.4 Push choke drive button and choke drive lamp should be on.

• VSet 14.4 +/- 0.2• L-DFM Terminals• 2.5 Second LRC• Active Lamp Circuit - With Output• Ref. F-00M-225-401, 0-122-1AA-5BO, 0-122-9AA-0X0


for



M520 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



M524 B 12 14.6



1. POWER OFF:

2. POWER ON:




• F-L terminals• Lamp Activated• With FR Resistor


for



M536 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



IB252 B 12 14.4



1. POWER OFF:

2. POWER ON:



Remove White test Lead from Stator Light comes on. Reconnect Stator.Remove Red test Lead from Sense, Light comes on. Reconnect Sense.Remove Green test Lead from Lamp, voltage remains same. Reconnect Light.Remove White test Lead from Stator, Light and Ignition voltage goes to 12 volts.

• L-Terminal M5• Active Lamp Function - With Output• Lamp, Field, Choke Drive Short Circuit Protection


for



M528 B 12 14.4



1. POWER OFF:

2. POWER ON:




Stator Activated • OE Compliant Soft Start • Under Voltage Lamp • Field, Lamp, Choke - Short CircuitProtection


for



IB226 A 12 14.7



1. POWER OFF:

2. POWER ON:




for



IB297 B 24 28.3



1. POWER OFF:

2. POWER ON:



Connect FR to tester “LI”, Grey.

Remove White test Lead from Stator Light comes on. Reconnect Stator.Remove Red test Lead from Sense, Light comes on. Reconnect Sense.Remove Green test Lead from Lamp, voltage remains same. Reconnect Light.Remove White test Lead from Stator, Light and Ignition voltage goes to 12 volts.• W-L-15-S-DFM Terminals • OE Compliant Circuit Protection & Functions... 'With Stator Start,


for



F610 A 12 14.4



1. POWER OFF:

2. POWER ON:



To Check for presence of over voltage function-Press “over-voltage button”

• S-D-L Terminals (Sense-N/C-Light)• M3 Field Post• F610 noted to replace OE regulators having a white insert surrounding the heat sink.


for



F613 A 12 14.45



1. POWER OFF:

2. POWER ON:



To check presence of over voltage function- Press O.V. button

• AS-FR-IL Terminals• Soft Start• Over-Voltage Lamp Function• F613 noted to replace OE regulators having a green insert surrounding the heat sink.


for



IH768 A 12 14.6



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked "S". Filed lamp should still blink and the meter will indicateapproximately 15.5 volts.


for



IN460 A 24 28.0



1. POWER OFF:

2. POWER ON:



• Remove white lead from stator connection and note the following:... Indicator lamp should light and voltage stay the same

• Using VRC2010 to check for ‘Over Voltage’:... Push the ‘Field Diode’ switch and the ‘Field Diode Lamp’ will turn on.

• Ignition (IGN) activated.• Stator input turns off the Light.• Standard Lamp Circuit - No Output• Field Rating 3-Amps.• Typical Vsat 1.20-Volts, @ 3-Amps, 24-Volts.


for



IN6324 B 12 13.8



1. POWER OFF:

2. POWER ON:




Stator or RVC Activated.


for



M5-313 A 12V 14.2



1. POWER OFF:

2. POWER ON:



disconnect Sense, check the secondary voltage, it is 15.4+/-0.2V.

Light Activated.


for



IN447HD A 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect stator, the light is ON and the regulator is function.2. Push the Over Voltage Button on the pannel, the light will be ON.3. Push the Field Diode Button on the pannel, the field diode LED will be ON.

Ignition Activated.


for



IN453HD A 12 14.3



1. POWER OFF:

2. POWER ON:



1. Disconnect stator, the field light is ON and the regulator goes to 12V. Reconnect stator.2. Disconnect Sense, the setpoint is 14.5+/-0.2V and light comes on. Reconnect Sense.3. Push the Over Voltage Button on the pannel, the light will be ON.4. Push the Field Diode Button on the pannel, the field diode LED will be ON.

Ignition Activated. Remove Ignition, voltage goes to 12V and light is off.


for



IM342 A 12 14.6



1. POWER OFF:

2. POWER ON:



1. Disconnect SENSE, the set point is 15.6+/-0.2V.2. Disconnect Stator, the lamp light comes on, field light stays on and volts go to 12 volts..3. Disconnect Light, the part stops regulation.4. Push the Field Diode Button on the panel, the Field Diode LED is on.

Light Activated.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsCS130D


D9715 B 12 14.70



1. POWER OFF:

2. POWER ON:



1.POWER OFF: Set “Voltage Range” and “FLD” switches to desire settings; Connect the voltage regulatoras indicated in the diagram below, except for the “Computer” terminals.

2.POWER ON: Field lamp should blink and meter will indicate approximately the set point voltageindicated in the above table.

3.Connect black test lead to “Computer” terminal voltage goes to approx. 13.2 volts, Disconnect black test lead from“Computer” terminal. Disconnect “Stator” terminal, light comes on and voltage reads 12.0 volt and field light stays on.


for



IN3054 B 12 14.1



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the field lamp should blink, check the reading on the meter, it should be 13.9+/-0.2v.2. Disconnect Stator, the light should be ON, and voltage reads 12.0 volt and field light stays on.3. Disconnect Ignition, the part should stop regulation.4. Push the Field Diode Button on the panel, the Field Diode lamp should be on.

Ignition Activated.


for



IN302 A 12 14.3



1. POWER OFF:

2. POWER ON:



Remove red test lead from terminal marked “S”, lamp turns on and voltage remains the same. Reconnect.Remove white test lead from terminal marked stator, lamp light turns on an voltage goes to 12 volts with field lighton.


for



M5-313CN A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the set point should be 15.4+/-0.2V.

Light Activated.


for



IN6315 B 12 14.35



1. POWER OFF:

2. POWER ON:



1. Connect C terminal to the B- of VRC2010, the set point should be 12.7+/-0.2V.2. Remove C, disconnect Stator, the Light should be on, the regulator continues regulating.3. Connect Stator, disconnect Ignition, the regulator stops regulating.

Ignition Activated.


for



IN9252 A 12 14.2



1. POWER OFF:

2. POWER ON:



D+ Activated/Excited.


for



D2198 A 12 14.35



1. POWER OFF:

2. POWER ON:




for



IH701

IH701V

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:



Disconnect Stator, the light should comes on.

Light Activated


for



TRI744 A 12 14,4



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the set point should be 15.3+/-0.2v.2. Reconnect Sense, remove Stator, the Lamp comes on and the voltage goes to 12.0V.3. Reconnect Stator and push the ‘Over Voltage’ button on the panel, the Lamp comes on.

Stator Activated


for



IM498 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp comes on.2. Reconnect Stator, push the ‘Choke Drive’ button on the panel, the Lamp comes on.

Light Activated.


for



TRI341 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the set point should be 15.5+/-0.2v.2. Reconnect Sense, remove Stator, the Lamp comes on and the voltage goes to 12.0V.3. Reconnect Stator and push the ‘Over Voltage’ button on the panel, the Lamp comes on.

*Connect Black Test Lead to terminal marked “C”, voltage will drop to approximately 12.5v.


for



IB248 A 12 14.5



1. POWER OFF:

2. POWER ON:



Remove White Test lead from Stator Terminal, Lamp will come on, display will show 12 volts and field light willstay on. Remove Green Test lead and field light will turn off.


for



IM480 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect SENSE, the set point should be 15.6 +/- 0.2V, and the Light comes on.2. Reconnect SENSE, disconnect STATOR, the Light comes on.

Light Activated.


for



IN6343 B 12 13.5



1. POWER OFF:

2. POWER ON:



Disconnect Sense, the setpoint should be 13.85+/-0.2V, then reconnect.Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 13.5V Set Point indicate above is the 'default VSet' (no vehicle PCM input).

RC or STATOR activated


for



IN6349 B 12 13.5



1. POWER OFF:

2. POWER ON:



Disconnect Sense, the setpoint should be 13.85+/-0.2V, then reconnect.Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 13.5V Set Point indicate above is the 'default VSet' (no vehicle PCM input).

RC or STATOR activated


for



DE1650 B 12 14.3



1. POWER OFF:

2. POWER ON:



1. Push the Over Voltage button on the panel, the Lamp Light comes on.2. Push the Choke Drive button on the panel, the Choke Light comes on.

Stator Activated.


for



IN248 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Push the Choke Drive button on the panel, the Choke light comes on.

Ignition Activated


for

TRANSPO TESTER INSTRUCTIONStype regulatorsDELCO 5si


D850



1. POWER OFF:

2. POWER ON:




for



IY146 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect SENSE, the setpoint should be 15.3+/-0.2V,2, Reconnect SENSE, then connect C terminal to the B-, the setpoint should be 12.7+0.2v/-0.3v.

Light Activated.


for



IN330 A 12 14.5



1. POWER OFF:

2. POWER ON:



Ignition Activated.


for



D1332 B 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the set point should be 14.5 +/-0.2V.2. Reconnect Sense and disconnect Stator, the Light Lamp comes on, and the Field Lamp dims.3. Reconnect Stator, push the Over Voltage button on the panel, the Light Lamp comes on.4. Push the Choke Drive button on the panel, the Choke Lamp comes on.

• Stator Activated• Over Voltage Lamp• Under Voltage Lamp• Field, Lamp short circuit protection• Active Lamp – With Output


for



IB5369 B 12 14.6



1. POWER OFF:

2. POWER ON:



1. Push the Choke Drive button on the panel, the Choke Light comes on.2. Disconnect Stator, the Lamp Light comes on, the Field Lamp is dim.

Stator Activated


for



IN6015 B 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 13.9+/-0.2V and the Lamp Light comes on.2. Reconnect Sense, and disconnect Stator, the Lamp Light comes on, and the field Light is dim.

Ignition Activated.


for



IN9254 A 24 27.9



1. POWER OFF:

2. POWER ON:



D+ Activated/Excited.


for



IB200 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on and the Field Circuit LED should be dim.2. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.3. Push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

• VSet 14.4 +/- 0.2• 15-61E Terminals (15=IGN, 61E=IL/Lamp)• With Soft Start & LRC• Ignition, Lamp, or Stator Activated• Active Lamp – With Output


for



IN209

IN210

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



IB390 A A 14.5



1. POWER OFF:

2. POWER ON:




for



D2295 A 12 14.7



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the set point should be 15.55+/-0.2V.

Light or Ignition Activated.


for



TRI851HD A 12 14.5



1. POWER OFF:

2. POWER ON:



Do not conncet FR and C.1. Disconnect Stator, the Lamp Indicator comes on and the Field Circuit LED should be dim.2. Reconnect Stator, and connect the C terminal to B-, the set point should be 12.6+/-0.2V.3. Disconnect C terminal, push the Over Voltage button on the panel, the Lamp Indicator comes on.

• Lamp Activated• With soft start and LRC• Over Voltage Lamp function


for



IN373 A 24 28.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on, and the Field Circuit LED comes dim.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

Ignition ActivatedActive Lamp -- With OutputWith Soft Start


for



D10

D10SE8

D10SE24

DE608

A

A

A

A

12

8

24

12

14.8

9.6

27.5

14.7


D21

DE610

D30

A

A

A

12

12

24

14.0

14.7

27.5


1. POWER OFF:

2. POWER ON:




for



IY145 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.3+/-0.2v.

Light Activated.


for



IB5353 A 12 14.4



1. POWER OFF:

2. POWER ON:



Remove test lead from terminal marked "Stator" - the Field light and Lamp will come on andVoltage will show 12 volts.

Push the Choke Drive button on the panel, the Choke Drive Indicator will come on.

• L-FR Terminals• With LRC and Soft Start• Active Lamp Circuit - with Output• VRC101-34 adapter shown for enhance stator signal, not all late model regulators need enhance signal


for



IN6308 B 12 14.45



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on and the Field Circuit LED will dim.

Light ActivatedSoft Start2.2s LRC


for

TRANSPO TESTER INSTRUCTIONStype regulatorsVALEO


M512HD A 12 14.6



1. POWER OFF:

2. POWER ON:



1. Push the Over Voltage button on the panel, the Lamp Indicator comes on.2. Disconnect Stator, the Lamp Indicator comes on.

Ignition ActivatedWith Soft StartOver Voltage and Under Voltage lamp


for



IN348 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, Push the Choke Drive button on the panel, the Choke Drive Indicator should be on.

Ignition ActivatedSoft StartUnder Voltage LampP-IG-L Terminal FunctionActive Lamp -- With Output


for



IY289 A 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.6+/-0.2V.

Ignition Activated.


for



IB347 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IH743 A 12 14.3



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint is 15.3+/-0.2V2. Reconnect Sense, connected C to B-, the setpoint should be 12.75+0.25/-0.15V.3. Disconnect C, disconnect Stator, the Lamp Indicator comes on.4. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.

Lamp Activated.Over Voltage, Under Voltage Lamp.


for



IM844 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Connect C to B-, the setpoint should be 12.6-0.5/+0.4V.

Ignition Activated.Trio input turns off charge indicator lamp.


for



IN454 B 12 14.6



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the Lamp Indicator comes on.

Stator or Light Activated.Under Voltage LampSoft Start & LRC function.


for



M527 B 12 14.3



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. disconnect Stator, the Lamp Indicator comes on, and the Field Circuit led should be dim.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

Stator Activated.Soft Start & LRC functionActive Lamp -- With Output


for



IN6329 B 12 13.8



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing:1. Connect RC terminal to VRC2010 tester.2. Adjust Comm Voltage switch to position 13, Setpoint is 11.8.3. Adjust Comm Voltage switch to position 14, Setpoint is 13.3V.4. Adjust Comm Voltage switch to position 15, Setpoint is 14.4V.* The 13.8V Set Point indicate above is the 'default VSet' (no vehicle PCM input).

Stator or RVC Activated


for



D2206 A 12 14.6



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator should be on.3. Push the Field Diode button on the panel, the Field Diode LED should be on.

Soft Start & LRC functionIgnition or Light ActivatedOver Voltage and Under Voltage LampStandard Lamp -- Without output


for



IB861 B 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

Stator or Light Activated.Soft Start & LRC functionActive Lamp -- With Output


for



IM472HD A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.6+/-0.2V.2. Reconnect sense, and connect C to B-, the setpiont should be 12.7+/-0.2V.3. Disconnect C, Disconnect Stator, the Lamp Indicator comes on.4. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator should be on.

Light ActivatedSoft Start & LRC functionWith C-functionOver Voltage LampStandard Lamp -- Without Output


for



IB677 A 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.3. Push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

Light or Stator ActivatedSoft Start2 seconds LRCOver Voltage LampActive Lamp -- With Output


for



D3232 B 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 14.2+/-0.2V.2. Reconnect Sense,disconnect Stator, the Lamp Indicator comes on.3. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.

Light ActivatedSoft Start2.5s LRC functionOver Voltage, Under Voltage LampStandard Lamp -- Without Output


for



IB307BZ B 24 28.2



1. POWER OFF:

2. POWER ON:



Trio Excited.Trio connected to Light


for



IB308BZ B 24 28.2



1. POWER OFF:

2. POWER ON:



Trio Excited.Trio connected to Light.


for



IH741 A 12 14.3



1. POWER OFF:

2. POWER ON:



Connect the C terminal to VRC2010,push the COMPUTER button to check the C function.1. Disconnect Sense, the setpoint should be 15.2+/-0.2V2. Reconnect Sense, disconnect Stator, the Lamp Indicator comes on.3. Reconnect Stator, connect C to VRC2010, the setpoint should be 13.0+/-0.2V.

Light Activated.Soft start9s LRCField, Lamp short circuit protectionStandard Lamp, without output


for



IM545 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.

Soft Start2.5s LRCLight ActivatedOver Voltage, Under Voltage LampStandard Lamp -- Without Output


for



IM564 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.6V+/-0.2v, the Lamp Indicator comes on.2. Reconnect Sense, disconnect Stator, the Lamp Indicator should be on.3. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indicator comes on.

Light Activated.Soft Start function5.5s LRCOver Voltage LampStandard Lamp -- Without output


for



IH737 A 12 14.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.3+/-0.2V.2. Reconnect Sense, disconnect Stator, the Light should be on.

Light Activated.Soft Start9.2 seconds LRCStandard Lamp -- Without Output


for



IH745 A 12 14.4



1. POWER OFF:

2. POWER ON:




Light Activated.Soft Start9 seconds LRCStandard Lamp -- Without Output


for



H8615 A 12 15.3



1. POWER OFF:

2. POWER ON:




for



IB227 A 12 14.7



1. POWER OFF:

2. POWER ON:



1. Push the Over Voltage button on the panel, the Lamp Indicator comes on.2. Disconnect Stator, the Lamp Indicator comes on.

Light ActivatedSoft Start3 seconds LRCOV, UV Lamp


for



IM547 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should me 15.5+/-0.2V.2. Reconnect Sense, connect C to B-, the setpoint should be 13.1+/-0.2V.3. Disconnect C, disconnect Stator, the Lamp Indication comes on.4. Reconnect Stator, the Lamp Indication comes on

Light Activated.Soft Start function.6 seconds LRCField, Lamp short circuit protectionStandard Lamp -- Without Output


for



M550 B 12 14.45



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indicator comes on.

Stator or Light Activated.Soft Start function.4 seconds LRCUnder Voltage LampStandard Lamp -- Without Output


for



M511V A 12 14.5



1. POWER OFF:

2. POWER ON:



Trio Excited.


for



IN6365 B 12 14.35



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, connect C terminal to B-, the setpoint should be 12.7+/-0.2V.

Ignition Activated.C functionStandard Lamp Function -- Without Output.


for



IN6366 B 12 14.46



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, connect C terminal to B-, the setpoint should be 12.8+/-0.2V.

Ignition Activated.C function12 seconds LRCStandard Lamp -- Without Output


for



IN332 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indication comes on.

Ignition Activated.Soft start.9 seconds LRC.Under voltage Lamp


for



IB313 A 12 14.3



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indication comes on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indication comes on.

Soft Start function2 seconds LRCStator or Light ActivatedActive Lamp function -- With Output


for



M544 B 12 14.5



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect stator, the Lamp Indication comes on.

Stator Activated.Soft Start FunctionUnder Voltage Lamp.


for



IN265 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indication comes on.

Ignition Activated.


for



IM505 A 12 14.4



1. POWER OFF:

2. POWER ON:



Connect DRIVER to tester “PD”


for



IL7020JMP A 12 14.5



1. POWER OFF:

2. POWER ON:



TRIO Excited.


for



M564 B 12 14.5



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indication comes on.2. Reconnect Stator, Push “Choke Drive” on the panel, the Choke Drive Indication comes on.

Stator or Light ActivatedSoft Start Function5 seconds LRCUnder Voltage LampActive Lamp -- With Output


for



M546 B 12 14.4



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indication comes on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indication comes on.

Stator or Light Activated.Soft Start Function9 seconds LRCUnder Voltage LampActive Lamp -- With Output


for



IH784 A 12 14.4



1. POWER OFF:

2. POWER ON:



TRIO EXCITED


for



M6120 A 12 14.65



1. POWER OFF:

2. POWER ON:



TRIO excited.


for



M6132 A 12 14.65



1. POWER OFF:

2. POWER ON:



TRIO excited


for



IN266 A 24 28.3



1. POWER OFF:

2. POWER ON:



Ignition Activated.


for



M549 B 12 14.4



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indication comes on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indication comes on.

Stator or Light Activated.Soft Start Function9 seconds LRCUnder Voltage LampActive Lamp -- With Output


for



TRI738 A 12 14.5



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be 15.3+/-0.2V.2. Reconnect Sense, disconnect Stator, the Lamp Indication should be on.3. Reconnect Stator, push the Over Voltage button on the panel, the Lamp Indication should be on.

Soft Start Function3 seconds LRCOver Voltage, Under Voltage Lamp.


for



M564 B 12 14.5



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indication comes on.2. Reconnect Stator, Push “Choke Drive” on the panel, the Choke Drive Indication comes on.

Stator or Light ActivatedSoft Start Function5 seconds LRCUnder Voltage LampActive Lamp -- With Output


for



IL7044JMP A 12 14.5



1. POWER OFF:

2. POWER ON:



Trio Excited.


for



IL217 A 12 14.25



1. POWER OFF:

2. POWER ON:



Trio Excited.


for



M534 B 12 14.4



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Sense, the set point should be 14.3V, the Lamp Indication should be on.2. Reconnect Sense, Disconnect Stator, the Lamp Indication should be on.

Stator ActivatedSoft Start Function6s LRCUnder Voltage Lamp


for



M540 B 12 13.8



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect RVC terminal to VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 11.8V.2. Adjust Comm Voltage switch to position 14, Setpoint is 13.3V.3. Adjust Comm Voltage switch to position 15, Setpoint is 14.4V.

RC or Stator Activated.Soft Start FunctionVSet controlled by vehicle RVC system


for



M558 B 12 14.65



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indication should be on.

•B-Circuit, High side drive regulator•Stator or Lamp Activated•Soft Start•3 seconds LRC•Under Voltage Lamp


for



IB680 B 12 14.6



1. POWER OFF:

2. POWER ON:



1. Push the Choke Drive button on the panel, the Choke Drive Indicator comes on.2. Disconnect Stator, the Lamp Light comes on, the Field Lamp is dim.

soft start function8 seconds LRCActive Lamp function -- With OutputStator or Light Activated.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsMAGNETI MARELLI


IX124 A 12 14.2



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator should be on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indicator should be on.

IL or Stator Activated.Active Lamp -- With Output


for



M531 B 12 14.45



1. POWER OFF:

2. POWER ON:



Connect STA1 and STA2 to VRC2010. Turn the STATOR swicth to 150HZ.1. Disconnect Stator, the Lamp Indicator should be on.

Soft Start Function5 seconds LRCUnder Voltage LampStator Activated.


for



D104HD-264 A 24 26.4



1. POWER OFF:

2. POWER ON:



11/21/2014Revision: Date :1Product Group521Page

for



M5-332 A 12 14.3



1. POWER OFF:

2. POWER ON:



1. test with VRC2010 disconnect sense, the set point(DMM) is about 15.4V, the Lamp indicator is on

A circuit


for



IH746 A 12 14.4



1. POWER OFF:

2. POWER ON:




Light Activated.Soft Start9 seconds LRCStandard Lamp -- Without Output


for



IM264-2 A 12 14.5



1. POWER OFF:

2. POWER ON:



disconnect the SENSE, the setpoint(DMM reading) is about 15.2V


for



IN289 A 12 13.8



1. POWER OFF:

2. POWER ON:



1. Disconnect Sense, the setpoint should be about 14.5V. lamp on2. Reconnect Sense, disconnect Stator, the Light should be on.

A circuit, low side drivewith softstartwith LRCIGN actived


for



IH747 A 12 14.3



1. POWER OFF:

2. POWER ON:



disconnect the SENSE, the setpoint is about 15.2V, lamp is on

A circuit, low side drivelight activatedwith LRCwith soft startwith C function


for



M557 B 12 14.6



1. POWER OFF:

2. POWER ON:



disconnect the stator, lamp is on

B circuit, high side drivewith soft startwith under voltage


for



IB389 A 12 14.5



1. POWER OFF:

2. POWER ON:



A circuitwith LRC


for



IB160 B 12 14.4



1. POWER OFF:

2. POWER ON:



B circuit,low side driveSTA activated and light activated to softstartwithout LRCwith softstartwith F function


for



IX597 A 12 14.2



1. POWER OFF:

2. POWER ON:



A circuitwithout LRCwith choke drive


for



M5-2471 A 24 27.6



1. POWER OFF:

2. POWER ON:



A circuit,low side driveSTA actived


for



M556 B 12 14.4



1. POWER OFF:

2. POWER ON:



disconnect the SENSE,the setpiont is about 15.0V.

B circuit,high side drivelight/stator activatedwith LRCwith C functionwith soft start


for



IB266

IB266V

A

A

12

12

14.2

14.2



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Push the Choke switch and the "Choke Drive" will turn on.

A circuit,low side driveLight/Stator activatedwith softstartwith LRCwith FR function


for



F611 A 12V 14.0*



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing:1. Connect RC terminal to VRC2010 tester.2. Adjust Comm Voltage switch to position 13, Setpoint is 12.9V.3. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.4. Adjust Comm Voltage switch to position 15, Setpoint is 14.8V.* The 14.0V Set Point indicate above is the 'default VSet' (no vehicle PCM input).


for



IB5300 B 24 25.6



1. POWER OFF:

2. POWER ON:



B circuit,high side driveIgnition activatedwith softstartwith FR function


for



IN249 A 12 14.65



1. POWER OFF:

2. POWER ON:



A circuit,low side drive


for



M552 B 12 14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Disconnect the Stator terminal and the Lamp should turn ON.

B circuit, high side drivewith softstartwith LRCwith FR


for



DE708HD

DE708HD-B-V1

B

B

12

12

14.7

14.7



1. POWER OFF:

2. POWER ON:



B circuit, high side driveLight activedwith softstartwith LRC


for



D2262 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



IN462 A 24 28.5



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal and the Light should turn ON.Reconnect the Stator terminal, push the Over Voltage button, the light should turn ON.


for



IB9028 A 12 14.3



1. POWER OFF:

2. POWER ON:




for



M5-050AHD A 12 14.6



1. POWER OFF:

2. POWER ON:



Push the Choke switch and the "Choke Drive" will turn on.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsLEECE


L105746 A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IN373HD A 24 28.4



1. POWER OFF:

2. POWER ON:



1. Disconnect Stator, the Lamp Indicator comes on.2. Reconnect Stator, push the Choke Drive button on the panel, the Choke Drive Indicator comes on.

Ignition Activated


for

TRANSPO TESTER INSTRUCTIONStype regulatorsVALEO/MOTOROLA


M516SC-2 B 12 14.5



1. POWER OFF:

2. POWER ON:



Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.


for



IM688 A 24 28.45



1. POWER OFF:

2. POWER ON:



Push the choke drive and the "Choke Drive Indicator Lamp" will turn on.Disconnect the SENSE, Lamp will turn on.Reconnect SENSE, Lamp will turn off, disconnect the Stator, Lamp will turn on.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsValeo


M561 B 12 14.5



1. POWER OFF:

2. POWER ON:



Push the choke drive and the "Choke Drive Indicator Lamp" will turn on,Disconnect the Stator terminal, the Lamp should turn ON.


for



IX135 B 12 13.5*



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect C terminal to RCV of VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 13.0V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 15.0V.* The 13.5V Set Point indicate above is the 'default VSet' (no vehicle PCM input), disconnect the Sense, the set point will be13.9V +/-0.2V, and the Lamp Indicator comes on.


for



IY116 A 12 14.45



1. POWER OFF:

2. POWER ON:



Disconnect Sense, the Lamp Indicator comes on, and the set point will be 15.4V +/-0.2V.


for



IM558 A 12 14.7



1. POWER OFF:

2. POWER ON:



Connect IGNITION with B+, Connect COMPUTER terminal to C of VRC2010 tester. don’t connect FR.Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Push the "COMPUTER" switch and the Setpoint drops to 12.6V.Disconnect the Stator terminal and the Lamp should turn ON.


for



IH748 A 12 14.4



1. POWER OFF:

2. POWER ON:



Disconnect the Sense, the set point will be 15.4V +/-0.2V.Reconnect Sense, disconnect the Stator terminal and the Lamp should turn ON.


for



IM622 A 12 13.45



1. POWER OFF:

2. POWER ON:



Do not connect RC.Disconnect the Sense, the set point will be 14.0V +/-0.2V.Connect RC terminal to RCV of VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 13.0V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 15.0V.


for



IB6024 B 12 14.5



1. POWER OFF:

2. POWER ON:



Connect terminal to BSS of VRC2010, the SET POINT is adjustable and goes with the switch ‘COMMVOLTAGE’ to 13V, 14V or 15V, range is +/-0.2V.


for



IB321 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



IM992 A 12 14.4



1. POWER OFF:

2. POWER ON:



Disconnect the Sense, the set point will be 15.5V +/-0.3V.


for



IY727 A 12 14.4



1. POWER OFF:

2. POWER ON:



Connect TRIO and SENSE to B+.Disconnect the Sense, the set point will be 15.5V +/-0.3V.


for



IB362CN-2 A 24 28.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IN6601 A 12 13.4



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to RCV of VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 13.0V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 15.0V.


for



M530 B 12 14.4



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.


for



M560 B 12 14.8



1. POWER OFF:

2. POWER ON:



Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.


for



IN6315T B 12 14.35



1. POWER OFF:

2. POWER ON:



Connect terminal C with B-, Setpoint drops to 12.7+/-0.2V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsLingshan


IP129BCN A 24 28.3



1. POWER OFF:

2. POWER ON:




for



M524T B 12 14.65



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Disconnect the Stator terminal and the Lamp should turn ON.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsGauss


PG102

PG126

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:





for

TRANSPO TESTER INSTRUCTIONStype regulatorsDenso


IX137 B 12 13.5



1. POWER OFF:

2. POWER ON:



Use VRC2010 tester to complete RC voltage setpoint testing,Connect RC terminal to RCV of VRC2010 tester.1. Adjust Comm Voltage switch to position 13, Setpoint is 13.0V.2. Adjust Comm Voltage switch to position 14, Setpoint is 14.0V.3. Adjust Comm Voltage switch to position 15, Setpoint is 15.0V.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsNIKKO


IZ228 A 24 28.5



1. POWER OFF:

2. POWER ON:



Connect Sense, B+ and Trio to VRC B+.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsBosch


IB381HD A 24 28.05



1. POWER OFF:

2. POWER ON:




for

TRANSPO TESTER INSTRUCTIONStype regulatorsNIPPON Denso


IN6003SE B 12 15.0



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the set point will be 15.15V +/-0.2V, and the Lamp shouldturn ON.


for



IB368SE A 12 14.4



1. POWER OFF:

2. POWER ON:




for



M562 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



IB6026

IB6026CN

IB6026V

B

B

B

12

12

12

14.5

14.5

14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Push the choke drive and the "Choke Drive Indicator Lamp" will turn on.Disconnect the Stator terminal and the Light should turn ON.

Switch the STATOR to 450Hz.


for



M571 B 12 14.4



1. POWER OFF:

2. POWER ON:



Connect terminal to BSS of VRC2010, the SET POINT is adjustable and goes with the switch "COMMVOLTAGE" to 13V, 14V or 15V, range is +/-0.2V.


for



IX594 A 12 14.45



1. POWER OFF:

2. POWER ON:



Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.


for



M574 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



PG103 A 24 29.1



1. POWER OFF:

2. POWER ON:



Disconnect IGN, the setpoint should be 29.1+/-0.3V.Reconnect the IGN terminal, and disconnect TRIO, the setpoint will rise a little bit.


for



PG101 A 12 14.6



1. POWER OFF:

2. POWER ON:





for



PG133 A 24 28.6



1. POWER OFF:

2. POWER ON:





for



IB6056 B 12 13.9*



1. POWER OFF:

2. POWER ON:



Connect terminal to LIN of VRC2010, the SET POINT is adjustable and goes with the switch ‘COMMVOLTAGE’ to 13V, 14V or 15V, range is +/-0.2V.* The 13.9V Set Point indicate above is the 'default VSet' (no LIN input).


for



IB5356 A 12 14.4



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Booting time is 12.6s.Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.


for



IB387CN-B160 A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IN6011 B 12 14.45



1. POWER OFF:

2. POWER ON:



Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the set point will be 14.45V +/-0.2V.


for



IB238 A 12 14.5



1. POWER OFF:

2. POWER ON:





for



PG104 A 12 14.7



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+ of VRC2010.Disconnect the Sense, the set point will be 15.7V +/-0.2V.


for



IM295

IM295CN

A

A

12

12

14.8

14.8



1. POWER OFF:

2. POWER ON:



Connect TRIO and IGN to B+.


for



IB003 A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+ of VRC2010.


for



IN372 A 12 14.2



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Connect IGN and SENS to B+, the setpoint is 14.2+/-0.2V.Disconnect SENS, the setpoint goes to 14.5+/-0.2V and the Lamp should turn ON.


for



IB313

IB313S

A

A

12

12

14.5

14.5



1. POWER OFF:

2. POWER ON:





for



IB6037 B 12 14.5



1. POWER OFF:

2. POWER ON:



Connect terminal to LIN of VRC2010, the SET POINT is adjustable and goes with the switch ‘COMMVOLTAGE’ to 13V, 14V or 15V, range is +/-0.2V.


for



M543 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



D411HD-HM B 12 14.8



1. POWER OFF:

2. POWER ON:



Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the set point will be 14.8V +/-0.25V.


for



IB293 A 12 14.3



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Connect terminal to BSS of VRC2010, the SET POINT is adjustable and goes with the switch "COMM

VOLTAGE" to 13V, 14V or 15V, range is +/-0.2V.


for



IB6132 A 12 14.3



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Connect terminal to BSS of VRC2010, the SET POINT is adjustable and goes with the switch "COMM

VOLTAGE" to 13V, 14V or 15V, range is +/-0.2V.


for



IM473 A 12 14.6



1. POWER OFF:

2. POWER ON:



Disconnect SENSE, the Setpoint should be 15.6 +/-0.2V and the Lamp turn ON.Reconnect the SENSE terminal, disconnect the Stator terminal and the Lamp should turn ON.


for



M573 B 12 14.4



1. POWER OFF:

2. POWER ON:



Connect terminal to LIN of VRC2010, the SET POINT is adjustable and goes with the switch "COMMVOLTAGE" to 13V, 14V or 15V, range is +/-0.2V.


for



P8-393HD B 24 27.5



1. POWER OFF:

2. POWER ON:




for



M579 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



M5-329AHD A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal, the regulator should stop works.


for



IN437SERP A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IB6197 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



M576 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



IB5378 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



M5-280AHD A 12 14.2



1. POWER OFF:

2. POWER ON:





for



IB6135 B 12 14.4



1. POWER OFF:

2. POWER ON:





for

TRANSPO TESTER INSTRUCTIONStype regulatorsDenso


IX136 A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect the IGN terminal, the regulator should stop works.


for



M575 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



M572 B 12 14.7



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal and the Lamp should turn ON.


for



M5-338 A 12 14.3



1. POWER OFF:

2. POWER ON:





for



IM362 A 12 14.5



1. POWER OFF:

2. POWER ON:



Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the "Lamp Indicator" will turn on and the set point will be15.5V +/-0.2V.


for



IB885 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



IB059 A 12 14.3



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the Lamp should turn ON and set point will be 14.5V +/-0.2V.


for



IZ229 A 24 28.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB5289 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



IP2700V A 12 14.6



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



M568 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



D940-132 A 12 13.2



1. POWER OFF:

2. POWER ON:



Connect SENSE and TRIO to B+.


for



IM849 A 12 14.5



1. POWER OFF:

2. POWER ON:



Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Sense, the set point will be 15.7V +/-0.3V.


for



M566 A 12 13.6*



1. POWER OFF:

2. POWER ON:





for



M591 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



M542 B 12 14.5



1. POWER OFF:

2. POWER ON:





for



IP1903

IP1903V

A

A

12

12

14.6

14.6



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IN6335CN B 12 14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Connect C to B-, the setpoint should be 12.85+/-0.2V.Disconnect C, disconnect the Stator terminal and the Lamp should turn ON.


for



IN393 A 12 14.25



1. POWER OFF:

2. POWER ON:



Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator, disconnect Sense, the Lamp should turn ON and the set point will be 14.6V +/-0.2V.


for



IN456 A 12 14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR and C terminal.Push the Choke switch and the "Choke Drive" will turn on.Push the "Over Voltage" switch and the "Lamp Indicator" will turn on.Disconnect the Stator terminal and the Lamp should turn ON.Reconnect Stator, connect C with GND, the set point will be 12.6V +/-0.2V.


for



M578 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



IB6066 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



IM691 A 24 28.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.Push the Choke switch and the "Choke Drive" will turn on.Disconnect the Sense, the set point will be 28.5V +/-0.2V.Reconnect Sense, disconnect the Stator terminal and the Lamp should turn ON.


for



IB6011 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



M521 B 12 14.45



1. POWER OFF:

2. POWER ON:





for



IM847 A 12 14.4



1. POWER OFF:

2. POWER ON:





for



IB276 A 12 14.5



1. POWER OFF:

2. POWER ON:





for



IB678 A 12 14.3



1. POWER OFF:

2. POWER ON:





for



IB510 A 12 14.3



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.Disconnect the Sense, the set point will be 14.5V +/-0.3V.


for



M547 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



IB262 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



IB6866 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



IL225 A 24 28.5



1. POWER OFF:

2. POWER ON:




for



M545 B 12 14.6



1. POWER OFF:

2. POWER ON:





for



D805 B 24 28.3



1. POWER OFF:

2. POWER ON:



Disconnect the Sense, the set point will be 28.3V +/-0.3V.Disconnect the IGN, the regulator should stop works.


for



IP135BNV

IP135BN

A

A

12

12

14.3

14.3



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



M511V-G64 A 12 14.15



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IP729BNV

IP729BN

A

A

24

24

28.5

28.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IP129BNV

IP129BN

IP129BN-285V

IP129BN-285

A

A

A

A

24

24

24

24

27.5

27.5

28.5

28.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB5881 B 12 14.3



1. POWER OFF:

2. POWER ON:





for



IB6150 B 12 14.4



1. POWER OFF:

2. POWER ON:





for



IB363T A 24 28.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB351T A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB387T A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB385T A 12 14.5



1. POWER OFF:

2. POWER ON:



Connect TRIO to B+.


for



IB350T

IB353T

IB355T

A

A

A

12

12

12

14.2

14.5

14.5



1. POWER OFF:

2. POWER ON:




for



IB388T A 12 14.5



1. POWER OFF:

2. POWER ON:




for



IB5225 A 12 14.5



1. POWER OFF:

2. POWER ON:



Do not connect the FR terminal.• Push the Choke switch and the "Choke Drive" will turn on.• Remove white test lead from terminal marked "Stator" - the Field light and Lamp will come on and

Voltage will show 12 volts.• Remove green test lead from "light" terminal , field light will go out and voltage stays at 12 volts.


for

TRANSPO TESTER INSTRUCTIONStype regulatorsBosch


IB543 B 24 28.3



1. POWER OFF:

2. POWER ON:



Disconnect the Stator terminal and the Lamp should turn ON.Reconnect the Stator terminal, disconnect the Sense, the Lamp should turn ON.


for



D10ACBD B 12 14.0



1. POWER OFF:

2. POWER ON:





for



IX491 A 12 14.4



1. POWER OFF:

2. POWER ON:




for



IM569 A 12 14.7



1. POWER OFF:

2. POWER ON:



Connect terminal COMPUTER with B-, Setpoint drops to 12.8V.


Notes

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

_______________________________________________

CANADAMontréal4711 Boul. CoutureMontréal (St-Léonard), Québec, H1R 3H7 Tel: 514.324.7922Toll Free: 800.661.2962Fax: 514.328.1535

Toronto34 Alex AvenueVaughan, OntarioL4L 5X1 Tel: 416.740.9200Toll Free: 800.387.2807Fax: 416.740.5348

EUROPE WAI Europe b.v.Klappolder 2252665 MR BleiswijkThe NetherlandsTel: 31(0)10.524.1980Fax: 31(0)10.524.1981

CHINATranspo Electronics, Shanghai, LTDBuilding No. 32 215 De Bao RdWai Gao Qiao Free Trade ZonePudong, Shanghai 200131 Peoples Republic of ChinaTel: 86.21.5048.2700Fax: 86.21.5048.2722

USAWAIglobal USA411 Eagleview Blvd., Suite 100, Exton, PA 19341Tel: 484.875.6600Toll Free: 800.877.3340 Fax: 800.948.6121

BRAZIL WAIglobal Brazil Ltda Av. Coronel Marcos Konder, 1207-Sala 7088.301-303, Itajai-SCTel/Fax: (47)3046.1600

ww

w.w

aiglobal.comC

M

Y

CM

MY

CY

CMY

K

vrc2010 tester manual 2015

Documents