vm-3-mpm1 - american communication systems · 2015. 12. 16. · motorola cdm-750, cdm-1250, gm-140,...

1

VM-3-MPM1

Voice Storage Module for Motorola Mobile Two-Way Radios

2BManual Revision: 2014-11-30

Covers Firmware Revisions: VS-1xxx: 1.62.00 and Higher

Covers Hardware Revisions: VS-MPx1: 7701D & Higher

This manual supports the following Motorola Mobile Two-Way Radios:

North America: CDM-750, CDM-1250, CDM-1550-LS+ EMEA Region: GM-140, GM-160, GM-340, GM-360, GM-380, GM-640, GM-660, GM-1280 Asia: GM-328, GM-338, GM-338-LS, GM-339, GM-398, GM-399, MCX-720, MCX-760, MCX-780 Latin America: PRO-3100, PRO-5100, PRO-7100, PRO-7200

2

HARDWARE SPECIFICATIONS Operating Voltage 4.75-8.2 VDC Operating Current Power Save Mode (COR Operation) 2.5 mA typical Power Save Mode (VOX Operation) 10 mA typical Normal Operation 17.5 mA typical Average w/COR Power Save (80-10-10 cycle) <5 mA Average w/COR Power Save (90-5-5 cycle) <4 mA Operating Temperature -30 - +60 C Frequency Response 300-3000 Hz Input Impedance >45 k Input Level (TX) 0.05-2.5 VPP Input Level (RX) 0.05-2.5 VPP Audio Output Impedance < 1200 Ohm

INSTALLATION OVERVIEW

1. Test the radio for functionality. 2. Program the radio per the Radio Programming Section of this manual. 3. Install the unit into the radio per the Hardware Installation Section of this manual. 4. Program the unit per the Product Programming Section of this manual. Note: Midian is not responsible for any damage/loss resulting from the use of Midian’s products.

3

GENERAL INFORMATION Midian’s VM-3 is a voice storage module for use in two-way radios. The VM-3 can record approximately 3 minutes of voice messages. Recording of voice messages occurs based on a COR/CTCSS/Talk Group indication from the radio or from an indication in the radio that a selective call has occurred (if available). A button on the radio can then be used to play back what was recorded. In addition to the long recording time, one of the main benefits of the VM-3 voice storage module is that the recording blocks are not set in stone like most other voice storage modules. If the radio transmission is only 5 seconds in length the recording block only uses 5 seconds of the 180 seconds. Some competitive units have recording blocks of 30 seconds. If the recording is 5 seconds the other 25 seconds are lost, thus greatly reducing the actual total recording time.

4

RADIO PROGRAMMING Motorola CDM-750, CDM-1250, GM-140, GM-160, GM-328, GM-338, GM-398, PRO-3100, PRO-5100, PRO-7100 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable. 1. In the Radio Configuration Window under the Option Board Tab, select Advanced Option Interface as the

Option Board Type. Do not check the Option Board Configuration Download box.

2. When programming the “Conventional Personality”, check the Option Board Feature box for all channels that

require voice storage.

5

Motorola GM-339, GM-340, GM-360, GM-380, GM-399, PRO-7200 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable. 1. In the Per Radio Miscellaneous Window under the Global Tab, select “Advanced” as the “Option Board Type”

and set the RX Audio (Accessory Connector) to “Filtered Squelched”. Note: The Accessory Connector is the rear accessory connector, but this setting also affects the audio going to the options connector.



6

Motorola CDM-1550-LS+, GM-338-LS Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable. Conventional Programming: 1. In the Radio Configuration Window under the Option Board Tab, select Advanced Option Interface as the

Option Board Type. Do not check the Option Board Configuration Download box.



7

LTR Programming: 1. In the LS Trunking Personality window, check the Option Board Feature box for each personality. Check the

Option Board Feature box for all channels that require the voice storage.

8

Motorola GM-640, GM-660, GM-1280, MCX-720, MCX-760, MCX-780 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable. 1. In the Per Radio Parameters Window set the “Option Board Fitted Mode” as “Advanced”.

2. Edit the ‘MPT Personality’. In the “Options” window, check the “Option Board Enable” box. Check Option

Board Enable for all channels that require the voice storage.

9

3. If using conventional channels, edit the ‘Conventional Personality Data’. In the “Conventional Personality”

window, check the “Option Board Enable” box.

10

HARDWARE INSTALLATION

Be certain to follow standard anti-static procedures when handling any of Midian’s products. Radio Firmware: Midian recommends installing the module into the radio with the existing firmware of the radio provided the firmware is at least R03.01.00. If the radio has a firmware version older than R03.01.00, it must be upgraded. If there are any issues with the firmware then the firmware should be upgraded to the latest. Verifying the firmware version can be done several ways. On most radios, this information is on a label on the back of the radio. For keypad & display radios, selecting the SoftwareVer# option from the utility menu will report the version. Consult Motorola if you cannot determine the firmware version. Disassembling the Radio: Complete disassembly instructions are available in Motorola’s Basic Service Manual.

1. Remove the antenna, knobs, and battery.

2. With a Chassis Opener tool from Motorola or a 3/16” flat blade screwdriver, gently insert the tool into the space between the case and the radio chassis at the bottom of the radio. Gently pull the tool downwards, separating the bottom of the chassis from the case. Make certain the rubber seal does not get damaged.

3. Pull the bottom of the chassis downward until the knob switches are clear from the case. Flip the chassis

open so that the bottom of the case and the bottom of the chassis are end to end. Be careful when opening; as there are flex cables installed.

4. Lift the latches on the main board to release the 40-pin flex cable and the Speaker’s 20-pin flex cable

from their connectors.

5. Remove the RF shield in the front cover. This is done by inserting a flat blade screwdriver or a scribe behind the arm tab, pushing down, and then prying inwards. The tab should pop out. NOTE: Do not pry upwards from underneath the arm as damage could occur to the keypad electronics or the unit if already installed. After releasing all 4 arm tabs, gently lift the bottom of the RF shield and then pull downward to get the 2 top tabs clear of the case.

Installation:

1. For radios without a keypad and display, there may be a plastic piece in the front cover that should be removed, leave the rubber piece (if present) installed. For radios with a keypad and display, unlatch the flex connectors from the keypad electronics, remove the flex cables, and remove the keypad electronics.

2. Insert the 40-pin flex cable into the 40-pin flex connector on the unit, making certain it is seated properly,

then close the latch. Install the unit with the 40-pin connector towards the bottom facing up.

11

3. Reinstall the display flex and close the latch. Insert the other side of the 40-pin flex cable into the 40-pin flex connector on the radio’s main board. Reinstall the speaker flex and close the latch.

Reassembling the Radio: Complete reassembly instructions are available in Motorola’s Basic Service Manual.

1. Reinstall the RF shield over the Midian board, by first inserting the 2 top tabs and then snapping the 4 arm tabs back into place with a small flat blade screwdriver. Be certain the board is squarely aligned and not to damage the flex cables. The RF shield may bulge slightly in the center; this is normal.

2. Place the chassis into the front cover. Be certain the O-ring seal is properly aligned and does not get damaged. Push the chassis up into the case and then push the bottom down until it snaps.

3. Replace the knobs, antenna and battery.

12

PRODUCT PROGRAMMING

Install the MPS programming software if you have not done so already. The units are programmed through the radio using the Motorola RIB box and cable or RIBless cable and our MPS software. Start the MPS. From the product selection screen in the software, locate and select the desired unit model and click OK. Configure the programming software by selecting File->Preferences and make certain there is a check mark next to ‘Rib Box Enable’ by clicking on it. Also select the appropriate COM port. Set the parameters of the software to fit the application. If any clarifications on a feature are required, move the mouse cursor over the feature name until the question mark appears and right click, an on-line help for that feature will be shown. The programming software always defaults to “MDC Portable” as the radio type. On the basic settings tab it is necessary to select the proper radio type. After entering the parameters, save the file by going to File - Save As. Enter the file name in the File Name block and click Save. Saving the file will allow for quick and easy reprogramming of units. Turn power on to the radio and then the RIB. Click ProgramUnit! in the software. To read the parameters from the unit, Click on ReadUnit!. The radio and RIB should be powered down for 5 seconds after reading or programming.

Unit Information This information area is updated when a unit is read or programmed. It will also be updated when a data file is loaded from a previous unit read and then saved. Below is a summary of the fields: Product - Shows a more detailed description of the product model within the series. uP #1 Firmware Version - Indicates the reported Firmware Version of the microcontroller of this product. uP #1 Loader Version - Indicates the reported Loader Version of the microcontroller of this product.

13

Power Up: Enables a short beep sequence that takes place immediately after power-up. Error: This beep may be triggered by any input event if programmed to do so. For example, if a long press on the Mode Input is not assigned to a function, it may be configured to generate the error beep. Mode: This is used to indicate to the user when a mode has been enabled or disabled. Voice Compression: If checked the VM-3 can store up to 3-minutes of voice. If left un checked the VM-3 can store up to 2.25 minutes of voice, but with a higher level of audio quality.

14

Enable Call LED: Enables voice mailbox control of the Call LED output. When record mode is started and there are no messages, the Call LED will glow steadily. After messages have been recorded, the Call LED will blink to indicate the number of messages that have been recorded. For example, if there are three messages waiting, the LED will blink in the following pattern: blink-blink-blink-pause-blink-blink-blink-pause… If there are 10 or more messages the LED will blink only 10 times. If during record mode the voice mailbox is filled to capacity, additional messages will be missed. In that case, the Call LED will blink rapidly until the voice mailbox is no longer full. Receiver Stops Playback: Unless this box is checked, transmissions received off the air will not be heard while the unit is in playback mode. If this box is checked, playback mode will be stopped when COR (or VOX) becomes active so that receiver audio can be heard. The message playing at the time playback is stopped will not be erased. PTT Stops Record Mode: If this box is checked, pressing PTT will cause record mode to be stopped. Otherwise, pressing PTT will suspend record mode during the time PTT is pressed and resume record mode when it is released.

15

Beep Volume: Adjust the slider for the desired beep volume. This level is expressed as a percentage of max voice audio level. Over-The-Air-Signal Modulation: Adjust the slider for the desired beep volume. This level is expressed as a percentage of max voice audio level. For these radios Midian recommends using 78%.

Playback Level: This sets the volume level of the recorded voice to the radio’s speaker. Transmit Level: Not used in this product.

16

Short Press: This is a press and immediate release press. Long Press: This is a press, hold until beeps are heard and release press. The buttons can be programmed for record start/stop, playback start/stop, etc.

17

Radio Type: Select from the list the Radio Type that matches your radio. For example if the radio is a CDM-1250 or GM-140 you would select Conventional MDC Mobile or if the radio is a GM-640 you would select MPT Mobile.

The “Enable Audio PA Control” box must be checked. Otherwise please only adjust the parameters of this screen when advised to by Midian.

18

AUDIO LEVELS ALIGNMENT

This section describes how to determine and set the audio levels. Audio Levels Overview: To ensure the best audio quality, the unit must be configured to match the audio levels used by the radio. The unit uses programmable gain amplifiers to accomplish this. Determining the gain settings for these amplifiers is an involved process, so Midian simplified this process by developing an algorithm that requires the technician to make only four voltage measurements. From these four measurements, all of the many internal settings are determined. Still, getting the best audio quality will likely require a bit of trial and error. The unit only has control of audio voltage levels, not input and output impedances. These impedances can dramatically influence the levels. The Four Voltage Measurements: An oscilloscope and a communications test set/service monitor are required for the measurements. It is recommended that the measurements be recorded in units of mV peak-to-peak. Each measurement must be taken with system modulation at either 60% or 100%, but Midian recommends using 60% These measurements must be taken within 15 seconds of powering the unit on. This is because the unit will enter power saving mode after that time. Measurements made while the unit is in power saving mode will not be valid. TX Alignment Set-Up: A method for controlling transmit modulation is required for accurate measurements in the TX mode. A small speaker held in place near the microphone by a rubber band can serve this purpose in most cases. Use a sine-wave generator to inject a 1000 Hz tone into the speaker. Adjust the output of the sine wave generator so that the transmitter produces 60% of rated modulation while PTT is pressed. Note that if the audio source (such as a speaker) is moved even slightly, the TX modulation may change significantly. Care must be taken to avoid changing the TX modulation while taking the measurements. RX Alignment Set-Up: Using a service monitor send a fully quieting signal (-50 dBm) to the receiver with a 1000 Hz tone at 60% modulation, adjust the volume of the receiver to a comfortable listening level and measure the audio level at the speaker using an AC coupled oscilloscope. Once the volume is adjusted and the measurement taken do not adjust the volume control during the remainder of the alignment. 1. TX Input: The goal of this procedure is to determine the audio level that the unit board will see at the TX

audio pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP1 on the unit.

2. RX Input: The goal of this procedure is to determine the audio level that the unit board will see at the RX audio pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP2 on the unit.

3. In the programming software under audio levels set the TX In to the same level as measured in step 1 and for a preliminary adjustment set the TX Out for the same level. Set the RX In to the same level as measured in step 2 and for a preliminary adjustment set the RX Out for the same level. Program the unit.

4. RX Output: The goal of this procedure is to determine the audio level that would normally appear at the RX audio insertion point in an unmodified radio. Using the same RX Alignment Set-Up procedure verify the audio level at the speaker is still at the same level measured initially in the RX Alignment Set-Up procedure. If not adjust the RX Out level accordingly.

5. TX Output: The goal of this procedure is to determine the audio level that would normally appear at the TX audio insertion point in an unmodified radio. Using the same TX Alignment Set-Up procedure verify the modulation is still at 60%, if not adjust the TX Out level accordingly.

19

Programming the Audio Levels: After determining the audio levels at the audio hookup points, it will be necessary to program the unit to match these levels. In the programming software, there is a slider control on the Audio Levels Screen for each of the of four audio hookup points. Locate the column that corresponds to the modulation and units of measurement for each of the audio hookup points. Adjust the slider bar such that the value appearing in the appropriate column matches what was measured as closely as possible. Radio Model RX In TX In RX Out TX Out CDM-750, CDM-1250, GM-140, GM-160, GM-328, GM-338, GM-398, PRO-3100, PRO-5100, PRO-7100

876 216 192 222

GM-340, GM-360, GM-380, GM-339, GM-399, PRO-7200 1044 222 240 216 GM-338-LS, CDM-1550-LS+ 678 138 150 138 GM-640, GM-660, GM-1280, MCX-720, MCX-760, MCX-780

20

OPERATION

Record Mode:

Pressing the button assigned in programming as Record Start, Toggle Record Start/Stop or Playback Stop/Record Start will cause the unit to record incoming transmissions when COR is detected. Pressing the button assigned in programming as Record Stop or Toggle Record Start/Stop will stop the record mode.

Playback Mode:

Pressing the button assigned in programming as Playback Start, Toggle Playback Start/Stop or Record Stop/Playback Start will cause the unit to start the playback of recorded transmissions. When the message is done playing you will hear three medium tone beeps followed by a high tone beep, once these beeps are done being generated the previous message will be deleted. To replay the message before it is deleted press the Playback Start button and the message will start over. This can be done anytime during the message. If during a message you wish to delete the current message and advance to the next message press the button assigned as Playback Advance.

TECHNICAL NOTES

Radio Compatibility: Midian has taken the utmost care to ensure the option board integrates into the radio with minimal impact to the features of the radio. However, some features may not be available in the radio when an option board is used. If a feature is not available, please contact Midian to see if the feature can be added.

Radio Firmware: Midian recommends installing the module into the radio with the existing firmware of the radio provided the firmware is at least R03.01.00. If the radio has a firmware version older than R03.01.00, it must be upgraded. If there are any issues with the firmware then the firmware should be upgraded to the latest. However, it should be noted that occasionally firmware updates may cause a conflict with proper option board/radio communications. This may appear that the unit is not working properly, but it is a conflict in the serial communication between the option board and radio.

For installation into MPT-1327 capable radios Midian recommends a minimum radio firmware version of R02.04.00. Firmware versions prior to this did not allow option board operation in both conventional and trunked modes.

Option Board Feature: Enabling the option board feature tells the radio to report events such as button press, PTT press, carrier detect, etc. to the option board. This feature enables communication between the option board and the radio. On display models, the following icon appears on the LCD when option board mode is on:

MIDIAN CONTACT INFORMATION

MIDIAN ELECTRONICS, INC. 2302 East 22nd Street Tucson, Arizona 85713 USA

Toll-Free: 1-800-MIDIANS Main: 520-884-7981 E-mail: [email protected] Web: HUwww.midians.comU

1

1

2

2

3

3

4

4

5

5

6

6

D D

C C

B B

A A

47KR2

+3.3V

560pC1

+3.3V

560pC2

47KR7

47KR6

560pC4

100KR15

100KR14

+3.3VDD.1uC7

2RR49

2RR50

2RR51

+3.3V

+3.3VA

+3.3VDD

8.2KR16

27KR13

.1uC10

.01uC9

4.7KR8

+3.3V

VAN

.0068uC15

.0068uC16 56K

R18

36KR21

.001uC18

75KR19

VAN

1.2MR20

VAN

10KR9.1u

C12

VAN

100pC14

10K1%R11

10K1%R12

10KR10

39pC44

+3.3V+3.3V

.1uC25

.01uC21

560pC19VAN

TP8

TP18

TP7

TP6

TP17

TP5

TP12

TP3

TP4

TP1

TP2

.01uC45

P4:1

P4:2

P4:3

P4:4

P4:5

P4:6

.1uC28

.1uC29

.1uC30

.1uC31

10uC36

10uC35

10uC32

12pC38

100pC39

32 KHzY1

+3.3V

+3.3V

+3.3VDD

+3.3VA

+3.3V

VDDD

4.7KR30

+3.3V

47KR31

+3.3V

VDDD

VDDD

100KR34

100KR35

560pC37

.1uC41

10uC40+3.3V

SW_B+

SRD_SND

SCK_SND

100pC617

VDDD

0RR32

PTT_IN_OUT

4001Q1

4001Q2

*Q6

0RR52

SB1D1

SB1D2

SB1D4

SB1D3

560pC11

0RR57

0RCR58

47KR36 +3.3V

+3.3V .1uC43

SB1D6

.1uC42

RESET

CP

CJS2009-03-25 AWS

2014-26-08

F-1

1 of 2 7701SCHEMATIC

Copyright © 2014

MIDIAN ELECTRONICS, INC.DATE:DESIGN:

UPD BY:REV:

APPR

REV

SHEET PROJECT NUMBER

DOCUMENT NAMEVS SERIES PRO

2.2uC13

SERIES VR2 VR3 U3 U6 U10VS-1200/110/1100 Y Y Y * *

VS-1000VS-1050

SVR-1/VM-3TS-120VAE-1

* * * * ** * * * Y* * * Y ** * * * Y* * * Y Y

* = NOT INSTALLEDY = INSTALLED

R570R0R0R0R0R225

R580R0R0R0R0R

*****

*R1

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206 3.3V

VR1

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206

VR2

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206

VR3

.01uC47

.22uC33

0RL1

2.2uC27

2.2uC26

22pC24

3.3KR24

*R17

2.2uC20

*C52

-

+

2

31

411

LMV324U7:1-

+

6

57

LMV324U7:2

-

+

9

108

LMV324

U7:3

-

+

13

1214

LMV324U7:4

3

1

2

4

5 6

U5

7 482 5

16 3

U4

16

13

42

11

9

4

3

37

8

47

28

24

27

20

18

36

43

46

48

45

416

44

1 2 3840 39

34

21

227

35

17

19

29

25

2326

12

10

5

15

14

33323031

49

U1

CS1

SO2

SI5

SCK6

VCC 8

HOLD 7

WP 3

GND 4

AT26DF081AU6

CS7

SO12

SI13

SCK14

DVDD 1

INT29 INT18

GND 2

AVDD 6

GND 5

IADDR0 431011

MMA7455LU10

16

15

33

35

36

37

38

3

11

12

20

46

21

2

39

40

41

42

32 31 13 10 45 1743

30

29

26

27

28

5 14 34 44

1

4

67

8

9

18

19

22

23

24

25

47

48

U3

*C17

*C48

*C51

4.7KR54

4.7KR55

RDY

MISO

TX OUT

RX OUT

EXT MIC

OPT ENA

TX IN

RX IN

DIS IN

PTT_IN_OUT

VDDD

SW_B+

GND

-

+

33

114

52

LM321U12

1KR87

+3.3VA

.01uC85

47pC84

36KR88

120KR89

22KR28

130K1%R3

130K1%R4

.0068uC3

.0068uC6

27KR5

10KR23

10KR22

FLAT TX OUT

VDDD

22pC8

P3

:1

P3:2

P3:3

P3:4

P3:5

TABLE 1R3

CJS CT-1 * * * * *

******

R5 R29*******

Y* 0R

*R29

Y

1

2PROG IN

PROG OUT

P2

225*

+

10uC5

U12Y******

PIC101

PIC102COC1

PIC201

PIC202COC2

PIC301

PIC302COC3

PIC401

PIC402COC4

PIC501

PIC502COC5

PIC601

PIC602COC6

PIC701

PIC702COC7

PIC801

PIC802COC8

PIC901 PIC902

COC9

PIC1001

PIC1002COC10

PIC1101 PIC1102

COC11

PIC1201 PIC1202

COC12

PIC1301

PIC1302COC13

PIC1401

PIC1402COC14

PIC1501 PIC1502

COC15

PIC1601 PIC1602

COC16

PIC1701 PIC1702

COC17

PIC1801PIC1802

COC18

PIC1901

PIC1902COC19 PIC2001

PIC2002COC20

PIC2101 PIC2102

COC21

PIC2401

PIC2402COC24

PIC2501 PIC2502

COC25

PIC2601

PIC2602COC26PIC2701

PIC2702COC27

PIC2801 PIC2802

COC28

PIC2901 PIC2902

COC29

PIC3001 PIC3002

COC30

PIC3101


PIC3202COC32

PIC3301 PIC3302

COC33

PIC3501 PIC3502

COC35

PIC3601 PIC3602

COC36

PIC3701

PIC3702COC37

PIC3801

PIC3802COC38

PIC3901

PIC3902COC39

PIC4001 PIC4002

COC40

PIC4101 PIC4102

COC41

PIC4201 PIC4202

COC42

PIC4301 PIC4302

COC43

PIC4401

PIC4402COC44

PIC4501

PIC4502COC45

PIC4701 PIC4702

COC47

PIC4801 PIC4802

COC48

PIC5101


PIC5202COC52

PIC8401

PIC8402COC84

PIC8501

PIC8502COC85

PIC61701

PIC61702COC617

PICR5801 PICR5802

COCR58

PID101PID102

COD1

PID201PID202

COD2

PID301PID302

COD3

PID401PID402

COD4

PID601PID602

COD6

PIL101

PIL102

COL1

PIP201

PIP202

COP2

PIP301

COP3:1PIP302

COP3:2PIP303

COP3:3PIP304

COP3:4PIP305

COP3:5

PIP401 COP4:1

PIP402 COP4:2

PIP403 COP4:3

PIP404 COP4:4

PIP405 COP4:5

PIP406 COP4:6

PIQ10DPIQ10G

PIQ10S

COQ1

PIQ20DPIQ20G

PIQ20S

COQ2

PIQ60DPIQ60G

PIQ60S

COQ6

PIR101 PIR102

COR1

PIR201 PIR202

COR2

PIR301 PIR302

COR3

PIR401 PIR402

COR4

PIR501 PIR502

COR5

PIR601 PIR602

COR6

PIR701 PIR702

COR7

PIR801 PIR802

COR8

PIR901 PIR902

COR9 PIR1001 PIR1002

COR10

PIR1101 PIR1102

COR11 PIR1201 PIR1202

COR12

PIR1301

PIR1302

COR13

PIR1401

PIR1402

COR14

PIR1501

PIR1502

COR15 PIR1601

PIR1602

COR16

PIR1701 PIR1702

COR17

PIR1801 PIR1802

COR18PIR1901 PIR1902

COR19

PIR2001 PIR2002

COR20

PIR2101 PIR2102

COR21

PIR2201

PIR2202

COR22

PIR2301

PIR2302


COR24

PIR2801 PIR2802

COR28

PIR2901 PIR2902

COR29

PIR3001

PIR3002

COR30

PIR3101

PIR3102

COR31

PIR3201 PIR3202

COR32

PIR3401 PIR3402

COR34

PIR3501 PIR3502

COR35

PIR3601 PIR3602

COR36

PIR4901 PIR4902

COR49

PIR5001 PIR5002

COR50

PIR5101 PIR5102

COR51

PIR5201 PIR5202

COR52

PIR5401 PIR5402

COR54

PIR5501 PIR5502

COR55

PIR5701 PIR5702

COR57

PIR8701

PIR8702


COR88

PIR8901 PIR8902

COR89

COtb0sch1

PITP101

COTP1

PITP201

COTP2

PITP301

COTP3

PITP401

COTP4

PITP501

COTP5

PITP601

COTP6

PITP701

COTP7

PITP801

COTP8

PITP1201

COTP12

PITP1701

COTP17

PITP1801

COTP18

COTxt1

PIU101 PIU102

PIU103

PIU104

PIU105

PIU106

PIU107

PIU108

PIU109

PIU1010

PIU1011

PIU1012

PIU1013

PIU1014

PIU1015

PIU1016

PIU1017

PIU1018

PIU1019

PIU1020

PIU1021

PIU1022

PIU1023

PIU1024

PIU1025

PIU1026

PIU1027

PIU1028

PIU1029

PIU1030

PIU1031

PIU1032

PIU1033

PIU1034

PIU1035

PIU1036

PIU1037

PIU1038PIU1039PIU1040

PIU1041

PIU1042

PIU1043

PIU1044

PIU1045

PIU1046

PIU1047

PIU1048

PIU1049

COU1

PIU301

PIU302

PIU303

PIU304

PIU305

PIU306

PIU307

PIU308

PIU309

PIU3010

PIU3011

PIU3012

PIU3013

PIU3014

PIU3015

PIU3016

PIU3017PIU3018

PIU3019

PIU3020

PIU3021

PIU3022

PIU3023

PIU3024

PIU3025

PIU3026

PIU3027

PIU3028

PIU3029

PIU3030

PIU3031PIU3032

PIU3033 PIU3034

PIU3035

PIU3036

PIU3037

PIU3038

PIU3039

PIU3040

PIU3041

PIU3042

PIU3043

PIU3044

PIU3045

PIU3046

PIU3047

PIU3048

COU3

PIU401

PIU402

PIU403

PIU404

PIU405

PIU406

PIU407PIU408

COU4

PIU501

PIU502

PIU503

PIU504

PIU505 PIU506

COU5

PIU601

PIU602

PIU603

PIU604

PIU605

PIU606

PIU607

PIU608

COU6

PIU701

PIU702

PIU703PIU704

PIU7011COU7:1

PIU705

PIU706

PIU707COU7:2

PIU708

PIU709

PIU7010

COU7:3

PIU7012

PIU7013

PIU7014COU7:4

PIU1001

PIU1002

PIU1003

PIU1004

PIU1005

PIU1006

PIU1007

PIU1008

PIU1009

PIU10010

PIU10011

PIU10012

PIU10013

PIU10014

COU10

PIU1201

PIU1202

PIU1203

PIU1204

PIU1205COU12

PIVR101

PIVR102

PIVR103

PIVR104

PIVR105

COVR1

PIVR201

PIVR202

PIVR203

PIVR204

PIVR205

COVR2

PIVR301

PIVR302

PIVR303

PIVR304

PIVR305

COVR3

PIY101

PIY102COY1

PAC101PAC102COC1

PAC201PAC202COC2

PAC302PAC301COC3

PAC401PAC402COC4

PAC501

PAC502COC5

PAC602

PAC601

COC6

PAC701

PAC702

COC7

PAC802

PAC801

COC8

PAC901

PAC902

COC9

PAC1001PAC1002COC10

PAC1101 PAC1102COC11

PAC1201

PAC1202COC12


PAC1401

PAC1402COC14

PAC1501

PAC1502

COC15PAC1601

PAC1602

COC16 PAC1701PAC1702COC17

PAC1801PAC1802COC18

PAC1901PAC1902COC19

PAC2001PAC2002COC20


PAC2401

PAC2402COC24




PAC2801PAC2802COC28

PAC2901PAC2902COC29

PAC3001PAC3002COC30

PAC3101

PAC3102

COC31 PAC3201

PAC3202

COC32

PAC3301

PAC3302COC33PAC3501

PAC3502COC35PAC3601

PAC3602COC36

PAC3701

PAC3702COC37

PAC3801

PAC3802

COC38PAC3901

PAC3902

COC39


PAC4101PAC4102COC41


PAC4301

PAC4302COC43

PAC4401PAC4402COC44

PAC4501

PAC4502

COC45

PAC4701

PAC4702

COC47

PAC4801PAC4802COC48

PAC5101

PAC5102COC51

PAC5201

PAC5202COC52

PAC8402

PAC8401

COC84PAC8502

PAC8501COC85

PAC60901

PAC60902COC609 PAC61001

PAC61002COC610

PAC61101

PAC61102COC611PAC61201

PAC61202

COC612

PAC61301PAC61302COC613

PAC61501

PAC61502

COC615PAC61601PAC61602COC616

PAC61701

PAC61702COC617

PACR5801 PACR5802COCR58

PAD101

PAD102

COD1

PAD201 PAD202COD2

PAD301

PAD302

COD3

PAD401 PAD402COD4

PAD601PAD602 COD6

PAJ601013

PAJ60106

PAJ601019

PAJ60101PAJ60102

PAJ60103PAJ60104

PAJ60105

PAJ60107PAJ60108

PAJ60109PAJ601010

PAJ601011PAJ601012

PAJ601014PAJ601015

PAJ601016PAJ601017

PAJ601018

PAJ601020PAJ601021

PAJ601022PAJ601023

PAJ601024PAJ601025

PAJ601026PAJ601027

PAJ601028PAJ601029

PAJ601030PAJ601031

PAJ601032PAJ601033

PAJ601034PAJ601035

PAJ601036PAJ601037

PAJ601038PAJ601039

PAJ601040

PAJ6010APAJ6010B

PAJ6010CPAJ6010DCOJ601

PAJ602018

PAJ602017

PAJ602016

PAJ602015

PAJ602014

PAJ602013

PAJ602012

PAJ602011

PAJ602010

PAJ60209

PAJ60208

PAJ60207

PAJ60206

PAJ60205

PAJ60204

PAJ60203

PAJ60202

PAJ60201

PAJ6020B

PAJ6020A

COJ602

PAL101

PAL102

COL1

PAP201PAP202 COP2 PAP304 PAP303PAP305 PAP302 PAP301COP3

PAP404PAP406 PAP403PAP405 PAP402 PAP401COP4

PAQ10SPAQ10D

PAQ10GCOQ1

PAQ20SPAQ20D

PAQ20G

COQ2

PAQ60SPAQ60D

PAQ60GCOQ6

PAQ6010BPAQ6010C

PAQ6010ECOQ601

PAQ6020BPAQ6020C

PAQ6020ECOQ602

PAQ6030BPAQ6030C

PAQ6030ECOQ603

PAR101

PAR102

COR1

PAR201

PAR202COR2

PAR302

PAR301COR3

PAR402PAR401COR4

PAR502PAR501COR5

PAR601

PAR602COR6

PAR701

PAR702COR7

PAR801 PAR802COR8

PAR901

PAR902COR9

PAR1001

PAR1002COR10PAR1101PAR1102COR11

PAR1201 PAR1202COR12

PAR1301

PAR1302

COR13


PAR1501

PAR1502COR15

PAR1601

PAR1602

COR16


PAR1801PAR1802COR18

PAR1901 PAR1902COR19 PAR2001

PAR2002

COR20PAR2101 PAR2102COR21 PAR2202

PAR2201COR22PAR2302PAR2301COR23

PAR2401PAR2402COR24

PAR2802

PAR2801

COR28

PAR2902PAR2901COR29

PAR3001

PAR3002

COR30 PAR3101 PAR3102COR31

PAR3201PAR3202COR32

PAR3401

PAR3402COR34

PAR3501

PAR3502COR35


PAR4901

PAR4902

COR49

PAR5001PAR5002COR50

PAR5101

PAR5102

COR51

PAR5201PAR5202COR52

PAR5401PAR5402COR54

PAR5501PAR5502COR55



PAR8802

PAR8801COR88PAR8902

PAR8901

COR89

PAR60101 PAR60102COR601

PAR60201

PAR60202

COR602PAR60301 PAR60302COR603

PAR60401PAR60402COR604

PAR60501 PAR60502COR605


PAR60701 PAR60702COR607


PAR60901 PAR60902COR609



PAR61201

PAR61202COR612PAR61301

PAR61302COR613

PAR61801

PAR61802COR618

PAR61901 PAR61902COR619



PAR62201 PAR62202COR622

PAR62301

PAR62302COR623

PAR62501 PAR62502COR625

PAR62901

PAR62902COR629

PAR63001

PAR63002COR630


PAR63201

PAR63202

COR632







COtb0sch1

PATP101 COTP1

PATP201 COTP2

PATP301COTP3

PATP401COTP4

PATP501COTP5

PATP601COTP6

PATP701

COTP7

PATP801 COTP8

PATP1201

COTP12

PATP1701COTP17

PATP1801

COTP18

PAU101PAU102

PAU103PAU104

PAU105PAU106

PAU107PAU108

PAU109PAU1010PAU1011

PAU1012

PAU1013PAU1014

PAU1015PAU1016

PAU1017PAU1018

PAU1019PAU1020


PAU1024 PAU1025PAU1026

PAU1027PAU1028

PAU1029PAU1030

PAU1031PAU1032

PAU1033PAU1034

PAU1035PAU1036

PAU1037PAU1038


PAU1042PAU1043

PAU1044PAU1045

PAU1046PAU1047

PAU1048

PAU1049COU1

PAU3048PAU3047PAU3046PAU3045PAU3044PAU3043PAU3042PAU3041PAU3040PAU3039PAU3038PAU3037PAU3036

PAU3035

PAU3034

PAU3033

PAU3032

PAU3031

PAU3030

PAU3029

PAU3028

PAU3027

PAU3026

PAU3025

PAU3024 PAU3023 PAU3022 PAU3021 PAU3020 PAU3019 PAU3018 PAU3017 PAU3016 PAU3015 PAU3014 PAU3013PAU3012

PAU3011

PAU3010

PAU309

PAU308

PAU307

PAU306

PAU305

PAU304

PAU303

PAU302

PAU301

COU3

PAU401

PAU402

PAU403

PAU404 PAU405

PAU406

PAU407

PAU408

COU4 PAU506

PAU505

PAU504PAU503

PAU502

PAU501

COU5

PAU601

PAU602

PAU603

PAU604 PAU605

PAU606

PAU607

PAU608

COU6

PAU7014

PAU7013

PAU7012

PAU7011

PAU7010

PAU709

PAU708PAU707

PAU706

PAU705

PAU704

PAU703

PAU702

PAU701

COU7

PAU10014PAU10013PAU10012PAU10011PAU10010PAU1009PAU1008 PAU1007 PAU1006

PAU1005PAU1004PAU1003PAU1002PAU1001

COU10PAU1204

PAU1203 PAU1202

PAU1205

PAU1201

COU12

PAU60203

PAU60201

PAU60204

PAU60202

PAU60205COU602

PAVO102 PAVO101

PAVO10E

PAVO10CPAVO10B

PAVO103

PAVO104

PAVO105

PAVO106

PAVO107

PAVO108

PAVO109

PAVO1010

PAVO1011

PAVO1012

PAVO1013PAVO1014PAVO1015PAVO1016PAVO1017PAVO1018PAVO1019PAVO1020PAVO1021PAVO1022PAVO1023PAVO1024PAVO1025

PAVO1026

PAVO1027

PAVO1028

PAVO1029

PAVO1030

PAVO1031

PAVO1032

PAVO1033

PAVO1034

PAVO1035

PAVO1036

PAVO1037 PAVO1038 PAVO1039 PAVO1040 PAVO1041 PAVO1042 PAVO1043 PAVO1044 PAVO1045 PAVO1046 PAVO1047 PAVO1048

PAVO10A

PAVO1049

PAVO10GPAVO10D

PAVO10S

COVO1

PAVR103

PAVR101

PAVR104

PAVR102

PAVR105

COVR1

PAVR203 PAVR201

PAVR204

PAVR202

PAVR205COVR2

PAVR303PAVR301

PAVR304

PAVR302

PAVR305

COVR3

PAY101PAY102COY1

vm-3-mpm1 - american communication systems · 2015. 12. 16. · motorola cdm-750, cdm-1250, gm-140,...

Documents