viva e57 quickstar

7/24/2019 VIVA E57 QuickStar

1/10

VIVA 4G LTE Mini Router

Quick Start Guide


2/10

Thank you for choosing the VIVA 4G LTE Mini

Router (hereinafter referred to as the E57)

The supported functions and actual appearance are subject to the product purchased.The following pictures are displayed for illustration purposes only. For the product

selection details, consult your service provider.

This guide briey describes the functions of the E57. For details about how to set the

management parameters, see the Help section on the Web Management page.

If the E57 is placed in an environment with poor ventilation, it will become warm after

extended use. When the E57 temperature reaches a certain high tempreature, it will

switch off or disconnect from the network automatically to protect itself. If this happens,

please place the E57 in a well-ventilated area for heat dissipation and then restart it.


3/10

1

2

3

Application Scenarios

The Wi-Fi device or computer can connect to the internet through the E57. The

actual connection procedure depends on the operating system of the Wi-Fi device or

computer. You can perform the connection operations as prompted.

Scenario connecting multiple devices through Wi-Fi

Scenario connecting a single device through USB

Scenario multi-device access via Wi-Fi and USB atthe same time


4/10


5/10

1

2

3

4

5

6

: Signal strength from weak to strong.

: Battery level from low to high.

Screen

Signal strength

Network type

Wi-Fi

SIM card slot

SMS

Internet connection is set up

Wi-Fi is On.

Number of connected Wi-Fi devices.

2G/3G/4G: Connected to a 2G/3G/LTE network.

R: Data roaming is On.

New messages.

Number of new messages.

Network connection status.

Trafc statistics.

Data trafc information.

Connection time.

Note:

Wi-Fi: wireless connection quality.

WPS: protected setup. Data trafc information is for your reference only. For more accurate data trafc

information, please consult your service provider.


6/10

Before You Start Installing the SIM Cardand the BatteryInsert the SIM card in the card slot. Ensure the SIM card is facing in the right direction,

as shown in the gure below, and then slide the SIM card into the slot.

Note: When removing the SIM card, open the tab and gently press the SIM card in, then

release. The card will automatically pop out.

Do not remove the SIM card when it is in use. Otherwise, the card and the Wi-Fi may

be damaged, and data stored on the card may be lost.

Do not remove the SIM card when it is in use. Doing so will affect the performance

of your Mobile WiFi and data stored on the SIM card may be lost.

Installing the microSD CardInsert the MicroSD as shown below.

Note: The MicroSD card is an optional accessory. If a MicroSD card is not provided in

the package, you may buy one.

To remove the MicroSD card, press the card in gently. The MicroSD card will pop

out for removal.

Do not remove the MicroSD card when it is in use. Otherwise, the card and

the E57 may be damaged, and data stored on the card may be lost.


7/10

Charging the BatteryNote:If the battery has not been used for a long time, it must be recharged rst.

Method 1: Using the charger

Caution:Only use the charger compatible with the E57 and provided by the designated

manufacturer. If a charger incompatible with the device model or provided by other

manufacturers or vendors is used, the E57 may fail to work and damage to the device

may occur. At the same time, any national regulations on communications products or

warranty applicable to the E57 will be canceled. The charger is an optional accessory, if

the charger is not provided in the package you can contact your local dealer to buy one.

Method 2: Connecting to a PC for charging

Connect the Mobile Wi-Fi to a PC using a compatible data cable.


8/10

Accessing the Internet via Wi-Fi ConnectionNote:By default, management parameters are preset on the E57 according to the

requirements of VIVA, the service provider. You may follow the steps below to quickly

access the Internet. For details about how to set management parameters, see the Helpsection on the Web Management page.

Step1: Power on the E57Press and hold until the screen lights up. The E57 is powered on.

Note:Press and hold to power off the E57.

Step 2: Establish a Wi-Fi Connection (Below exampleuses Windows XP OS)1. Make sure that the Wi-Fi is enabled.

2. Select Start > Control Panel > Network Connections > Wireless Network Connection.

Note:To set up a Wi-Fi connection, the PC must have a wireless network adapter installed.

If Wireless Network Connectionis displayed, a wireless network adapter is available.

Otherwise, check to make sure you have a wireless network adapter installed.

3. Click View available (wireless networks) to display a list of wireless networks available.

4. Select a network indicated by the SSID of the E57, and then click Connect.

Note: If the encryption parameter is already set for the E57, the Wireless Network

Connectiondialog box is displayed. Enter the network password in the dialog box.

The SSID and network key label are afxed to your E57. Press the WPS button twice

to view the current SSID and wireless network encryption key on the screen. Wait until the wireless connection icon is displayed in the status area in the lower right

corner of the PC screen.


9/10

Mode

Auto

Manual

Operations

After the E57 is powered on, it can automatically connect to theinternet when data transmission is required. If data transmission is notperformed over a period of time, the E57 automatically disconnectsfrom the Internet connection.Launch the Web Management page and follow the prompts to connectto or disconnect from the network.

Step 3: Access the InternetAfter you establish a Wi-Fi connection successfully, you can access the Internet using

the following modes. By default, the mode is Auto.

Note: Launch the Web Management page to select the mode for accessing the Internet.

If the E57 accesses the roaming network, the E57 automatically disconnects fromthe established network connection. If you need to access the Internet from the new

network, you must re-establish a network connection.

Accessing the Web Management Page1. Make sure that the connection between the E57 and the device is properly established.

2. Start the Internet browser and enter http://192.168.1.1 in the address bar.

3. Enter the password and log in to the web management page.

Note:The default password is admin.

Create a Secure Connection1. Launch the web browser and enter http://192.168.1.1 in the address bar.

2. Enter the password and click login. The default password is admin.

3. Click on Settings.

4. Click on Quick setup. A message Welcome to the quick setup wizard will be shown.

5. Click on Next. A message Congure Prole Settings will be shown.

6. Click on Next. A message Congure Dial-up Settings will be shown.

7. Click on Next. A message Congure WLAN settings will be shown. Insert thedesired router name in the Name (SSID) eld

8. Click on Next. For the Authentication select Auto, for the Encryption mode

select WEP. Enter the desired network key in the Network key 1 eld. This key will

be requested every time a user tries to access this connection.

9. Click on Next

10. Click on Finish. A message The action will disconnect your connection, are you

sure to proceed? will be shown

11. Click on Ok.

Note:The password that you will set for your device should be in numerical format

(example 123456).


10/10

Daily UsePower Saving ModeIf no operation is performed on the E57 for a while, the screen turns off. Press any key to

light up the screen.

If the E57 is powered by the battery only, choose whether to enable the E57 to turn offWi-Fi automatically. If this function is enabled and no Wi-Fi devices access the E57 for a

set period, the E57 turns off Wi-Fi automatically. You can press any key to turn on Wi-Fi

again.

Establishing a WPSConnectionIf a Wi-Fi client connected to the E57

supports the WPS function, a network

key will be automatically generatedwithout manual input. To establish a WPS

connection, perform the following steps:

1. Power on the E57.

2. Start the client.

3. Enable the WPS function of the E57.

4. Enable the WPS function of the client.

Note: After Wi-Fi is enabled, press and hold the WPS button to enable the WPS function of

the E57.

For WPS operations on the client, see the user guide of the client.

Restoring Factory DefaultsIf you forget the changes you have made to some

parameters, you may restore factory defaults and

recongure the E57.

To restore the factory defaults: press and hold the

RESET button until the screen turns off. All factory

default settings will be successfully restored.

Note:Restoring factory defaults deletes all personal conguration settings and restores all

web-based management settings and parameters to their default values.

TipsIf you are experiencing difculties using the E57, try the following:

See the (Help) section on the Web Management page.

Restart the E57.

Restore the factory defaults.

Contact your service provider.

viva e57 quickstar

Documents