view hickory saw catalog (pdf - 47mb)
TRANSCRIPT
HICKORY SAW & TOOL, INC.
406 9th Street S.E., Hickory, N.C. 28602 P.O. Box 2407, Hickory, N.C. 28603
Telephone: (828) 324-5585 1-800-762-9899 Fax: (828) 324-5588 1-800-762-6845
www.hickorysawandtool.com
Table of Contents Cover page……………………………………………………………………….……..1-2 Dedicated Insert raised panel cutters……………………………..……………….…….3-4 Stile & rail cutter sets…………………………………………………………….……..5-6 Multi-profile cutters……………………………………………………………….…….7-8 Finger joint cutters………………………………………………………………….……..9 Pricing on Service work, saw blades, dado sets……………………………………...10-16 ICK Inserts……………………………………………………………………………17-18 Panel saws……………………………………………………………………………….19 Split scoring & conic scoring saws………………………………………………………20 Hogging units…………………………………………………………………….…..21-22 Type “C” four flute countersinks………………………………………………...………23 Woodworking drills, countersinks, multi-spur and boring bits………………………24-51 Diamond tipped cutters and router bits……………………………………………….52-53 Hydraulic and straight bore moulder heads…………………………………………..54-55 HSS, jointer and planer knives……………………………………………………….56-57 Tool holders & collets .…………………………………..…………………………..58-59 ONSRUD ……..………………………………………………………………….…60-126 Solid carbide bits……..……………………………………………………………127-130 Carbide tipped straight bits………………………………………………………...131-132 Stagger tooth & mortise bits…………………………………………………………....133 Round and half-round bits ………………………………………………………….….134 V-Groove, Panel, and cove bits…………………………………………………….…..135 Rabbeting, round-over, ogee, flush, and Laminate bits………………….………..136-140 Solid Surface and T-Slot bits……………………………………………………...141-142 Edge profile bits…………………………………………………………………...143-145 Handrail & Molding bits……………………………………………………………..…146 Glue joint bits……………………………………………………………………...147-148 Groove profiles…………………………………………………………………………149 MDF door profiles…………………………………………………………………...…150 Stile & rail router bits………………………………………………………………......151 Raised panel router bits……………………………………………………………..….152 Cabinet, Door & Drawer, Window Sash bits……………………………………...153-155 Dovetail bits…………………………………………………………………………….156Spoilboard & Slotting....................……………………………………………………..157 Dowel drills & Boring Bits.................................... …………………………………….158 Bearings & Accessories……………………………………………………………159-160 Pricing for pages (127-160)………………………………………………………..161-166 Conversion Charts…………………………………………………………………167-169
Page 2
RAISED PANEL CUTTERS
DETAILS Available with solid carbide or S-Alloy inserts. Has a constant cutting circle for the elimination of set ups, because inserts bolt against precision machined seats. All inserts have been designed for soft and hardwood, compound board and exotic hardwoods.
TECHNICAL SPECIFICATIONS: DIAMETER: 6” CUTTING CIRCLE BORE: 1-1/4” WINGS: 3 Clockwise or Counterclockwise rotation; material runs face down; “T” Bushings for ¾” spindle available upon request. Ball bearing rub collars are available upon request.
CUSTOM PROFILES AVAILABLE
Send us your pattern, and we will produce the tool to cut that profile. Hickory Saw and Tool can produce cutting tools to your exact specifications from wood samples, drawings, sketches, or existing tools.
MADE IN THE USA
These insert heads are produced in our Hickory, NC facility. Each cutting tool is specifically designed for your needs according to your specifications to achieve the best possible results.
Page 3Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
RAISED PANEL CUTTERS
Page 4
STILE AND RAIL CUTTER SETS
DETAILS Available with solid carbide or S-Alloy inserts. Has a constant cutting circle for the elimination of set ups, because inserts bolt against precision machined seats. All inserts have been designed for soft and hardwood, compound board and exotic hardwoods.
TECHNICAL SPECIFICATIONS: DIAMETER: 4” SMALL CUTTING CIRCLE BORE: 1-1/4” WINGS: 3 Clockwise or Counterclockwise rotation; material runs face down; “T” Bushings for ¾” spindle available upon request. Ball bearing rub collars are available upon request.
CUSTOM PROFILES AVAILABLE
Send us your pattern, and we will produce the tool to cut that profile. Hickory Saw and Tool can produce cutting tools to your exact specifications from wood samples, drawings, sketches, or existing tools.
MADE IN THE USA
These insert heads are produced in our Hickory, NC facility. Each cutting tool is specifically designed for your needs according to your specifications to achieve the best possible results.
Page 5Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
STILE AND RAIL CUTTER SETS
Page 6
MULTI-PROFILE CUTTERS
DETAILS Available with solid carbide or S-Alloy inserts. Has a constant cutting circle for the elimination of set ups. Utilizes HSS corrugated back backing plates so multiples of profiles can be achieved using only one cutter by just changing the inserts and backers. All inserts have been designed for soft and hardwood, compound board and exotic hardwoods.
TECHNICAL SPECIFICATIONS: DIAMETER: 4” SMALL CUTTING CIRCLE BORE: 1-1/4” WINGS: 3 Available in 40mm or 60mm wide; Clockwise or Counterclockwise rotation achieved with same cutter; material runs face down; “T” Bushings for ¾” spindle available upon request. Ball bearing rub collars are available upon request.
MOULDER & TENON HEADS ALSO AVAILABLE
These insert cutters can be supplied in any diameter and bore size per your requirements. Hickory Saw and Tool can produce cutting tools to your exact specifications from wood samples, drawings, sketches, or existing tools.
MADE IN THE USA These insert heads are produced in our Hickory, NC facility. Each cutting tool is specifically designed for your needs according to your specifications to achieve the best possible results.
Page 7Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
MULTI-PROFILE CUTTERS
Page 8
Page 9Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
PRICE LIST FOR C.T. CIRCULAR SAW BLADES =======================================================================
#OF TEETH DIA. > 0 TO 18" OVER 18" UP TO 36" ------------------------------------------------------------------------------------------------------------------------------- 0 - 29 . . . . . . . . . . . . . . . . . . . $10 . 00 . . . . . . . . . . .$16 . 00 30 - 40 . . . . . . . . . . . . . . . . . . . $14 . 00 . . . . . . . . . . .$24 . 00 41 - 60. . . . . . . . . . . . . . . . . . . . $15 . 00 . . . . . . . . . . . $25 . 00 61- 100. . . . . . . . . . . . . . . . . . . .$16 . 00 . . . . . . . . . . . $27 . 00 101 - 120. . . . . . . . . . . . . . . . . . $17 . 00 . . . . . . . . . . . $30 . 00 TIP REPLACEMENT =================== U P TO .220 KERF . . . . . . . . . . . . . . . . . . . . . . . .$1 . 50 EA. TIP OVER .220 KERF. . . . . . . . . . . . . . . . . . . . . . . SEE GROOVER TIP PRICE
COMPLETE RETIP ===================
TIP PRICE (X) NUMBER OF TEETH (NO SHARPENING CHARGE)
================================================================== DADO SETS ================== DADO SAWS . . . . . . . . . . . . . . . . . . . . . . . . . . SEE SHARPENING PRICES DADO FILLERS: KERF SHARPENING TIP REPLACEMENT
------------------------------------------------------------------------------------------------------------------------------------ 1 / 16 . . . . . . . . . . . . . . . . . . . . $ 6 . 00 . . . . . . . . . . . . . . . . . . $4 . 00 (EA. TIP) 1 / 8 . . . . . . . . . . . . . . . . . . . . $ 6 . 00 . . . . . . . . . . . . . . . . . . $4 . 00 (EA. TIP) 3 / 1 6 . . . . . . . . . . . . . . . . . $ 6 . 00 . . . . . . . . . . . . . . . . . . $4 . 00 (EA TIP) 1 / 4 . . . . . . . . . . . . . . . . . . . $ 8 . 00 . . . . . . . . . . . . . . . . . . $5 . 00 (EA. TIP) 5 / 16 . . . . . . . . . . . . . . . . . . . .$ 8 . 00 . . . . . . . . . . . . . . . . . . $6 . 00 (EA. TIP) 3 / 8 . . . . . . . . . . . . . . . . . . . . $ 8 . 00 . . . . . . . . . . . . . . . . . . $7 . 00 (EA. TIP) 1 / 2 . . . . . . . . . . . . . . . . . . . . $10. 00 . . . . . . . . . . . . . . . . . . $8 . 00 (EA. TIP) RETIP. . . . . . . . . . . . . . . . .#OF TIPS (X) TIP PRICE (NO SHARPENING CHARGE) =================================================================== MISCELLANEOUS SAW CHARGES OPENING BORE CHARGES ============================ UP TO 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$ 15 . 00 1" TO 1 1/2". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$ 20 . 00 1 1/2" TO 2 1/2". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$ 25 . 00 OVER 2 1/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 30 . 00 KEYWAYS BUSHINGS $20.00 EA UP TO 1". . . . . .$ 15 .00 1" TO 2". . . . . .$ 20 .00 2 TO 3" . . . . .$ 25 .00 HAMMER AND ROLL FOR TENSION AND STRAIGHTNESS UP TO 18" . . . . . . . . . . . . . . . . .$2 . 00 PER INCH OF DIAMETER OVER 18" . . . . . . . . . . . . . . . . .$3 . 00 PER INCH OF DIAMETER
Page 10
PRICE LIST FOR SHARPENING CARBIDE TIPPED WING CUTTER =========================================================================
# OF WINGS CUTTING EDGE WIDTH 1 / 2" 1" 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4- 1/2" ========================================================================= 2 $16.00 $16.00 $17.50 $17.50 $17.50 $20.50 $20.50 20.50 $22.50 3 $19.00 $19.00 $20.50 $23.00 $23.00 $23.00 $25.00 $25.00 $25.00 4 $20.00 $20.00 $22.50 $25.00 $25.00 $25.00 $27.50 $27.50 $27.50 6 $22.00 $22.00 $25.50 $29.00 $29.00 $29.00 $30.50 $30.50 $30.50 8 $25.00 $25.00 $28.00 $33.00 $33.00 $33.50 $35.50 $35.50 $35.50 10 $28.00 $28.00 $31.50 $36.00 $36.00 $36.50 $39.00 $39.00 $39.50 12 $28.00 $28.00 $31.50 $36.00 $36.00 $36.50 $39.00 $39.00 $39.50 (PRICE FOR OVER 4-1/2" WIDE: ADD $3.00 PER EACH 1/2" LARGER WIDTH) (RETIP PRICES QUOTED UPON REQUEST PER CUTTER) ========================================================================
PRICE LIST FOR GROOVERS # OF WINGS===== KERF> 1 / 4" 3 / 8" 1 / 2" 5 / 8" 3 / 4" ========================================================================= 2 ............................... $9.50 $10.00 $10.00 $11.50 $12.75 3 ............................... $11.50 $11.75 $12.50 $13.25 $14.25 4 ............................... $12.00 $12.25 $13.25 $14.00 $15.00 6 ............................... $13.75 $14.50 $16.00 $16.50 $15.75 8 ............................... $15.00 $15.75 $17.00 $18.00 $20.25 10 ............................... $16.50 $17.25 $18.75 $19.75 $21.50 12 ............................... $19.00 $20.50 $22.50 $23.00 $24.50 18 ............................... $22.00 $23.50 $25.25 $26.00 $28.00 24 ............................... $25.25 $26.50 $29.00 $30.00 $31.75
FOR KERFS OVER 3 / 4" GO TO CUTTER PRICE TIP REPLACEMENT FOR GROOVERS
1 / 4" 3 / 8" 1 / 2" 5 / 8" 3 / 4" $8.00 $8.00 $10.00 $12.00 $15.00
COMPLETE RETIP=+ #OF TIPS --NO SHARPENING CHARGE
Page 11Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
PRICE LIST FOR SHARPENING PROFILE HEADS =========================================================================
# OF WINGS UP TO 6" LONG OVER 6" LONG
-------------------------- --------------------------- -------------------------- 2 $22.50 $24.00
4 $24.50 $26.00
6 $24.50 $32.00
8 $27.50 $32.00
FOR MORE WINGS GO TO MOULDER HEAD PRICE
==================================================================== TIP REPLACEMENT IN PROFILE HEADS
===================================== 1 / 4" 3 / 8" 1 / 2" 5 / 8" 3 / 4" $8.00 $9.00 $10.00 $11.00 $13.00 COMPLETE RETIP = # OF TIPS NO SHARPENING CHARGE ======================================================================== PRICE LIST FOR SHARPENING SPIRAL PROFILE HEADS UP TO 6" LONG......$34.50 OVER 6" LONG.......$49.00 TIP REPLACEMENT ON SPIRALS QUOTED PER HEAD ========================================================================= PRICE LIST FOR SHARPENING STAGGERED TOOTH MOULDER HEADS
WIDTH ROWS OF TEETH PRICE 4 4 $31.50 4 6 $33.50 4 8 $36.50 4 12 $43.50 6 6 $41.50 6 8 $49.00 6 12 $53.00 8 6 $55.00 8 8 $60.00 8 12 $70.00 10 6 $61.50 10 8 $65.00 10 12 $75.50 12 8 $83.00 12 12 $93.00
Page 12
PRICE LIST FOR MISC. ITEMS
=========================================================================
HSS AND C.T. CARVING CUTTERS WIDTH: 0 TO 2" CEL. SHARPEN AND TURN DOWN COLLARS ------------------- $45.00 =========================================================================
HSS AND CT ROUTER BITS STRAIGHT CUT ...................................................................................... $8.00 GROUND TO PATTERN 2 WING.......................................................... $19.00 GROUND TO PATTERN 4 WINGBUC....................................................$22.00 REGRIND ENDS .................................................................................... $ 2.50 CUT OFF ................................................................................................ $ 3.50 REPROFILE 2 X SHARPENING PRICE ================================================================
HAUNCHING CUTTERS ------SHARPENING 2 PC. X 3" MAX CEL.. ...................................................$ 35.00 3 PC. OR 3" PLUS CEL. ...............................................$ 47.50 RETIP - - 3/4" TO 1-1/2" ..................................................$ 105.00 EA. PC. 1- 9/16" TO 3" ..................................................$ 150.00 EA. PC. ========================================================================
STRAIGHT CUTTING EDGE CORR.BACK MOULDER KNIVES HSS $1.00 PER INCH OF CEL. C. T. $2.70 PER INCH OF CEL. =========================================================================
GROUND TO PATTERN SHAPER & MOULDER KNIVES PER KNIFE SHARPEN & REPROFILE - COST PLUS $10.00 TEMPLATE CHARGE
HSS WIDTH OF KNIFE: 1" - - - - - - - - - -2" - - - - - - - - - -3" - - - - - - - - - -4" $13.00 - - - - - -$17.00 - - - - - $21.00- - - - - - -$22.00 -------------------------------------------------------------------------------------------- REPROFILE ONLY - - - - - - - - - - - - - - $13.00 TEMPLATE CHARGE -------------------------------------------------------------------------------------------- C. T. WIDTH OF KNIFE: 1" - - - - - - - - - -2" - - - - - - - - - -3" - - - - - - - - - -4" $19.00 - - - - - - $21.00 - - - - - - $23.00 - - - - - - -$25.00
Page 13Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
PRICE LIST FOR MISC. ITEMS ========================================================================= DRILL SHARPENING HSS. AND C.T. CARBIDE TIPPED HSS BRADPOINT 1 / 8 " TO 1 / 2 " - - - $4.50 = = = = = = = = = == = = = UP TO 5 / 16 " - - - - - - - $2.00 33 / 64 " TO 1" - - - - - $5.50 = = = = = = = = = = = = = = 11 / 32 " TO 1 / 2" $3.00 9 / 16 "TO 3 / 4" $4.50 13 / 16 " TO 1-1 / 8 " - - - $6.50 =========================================================================
MULTI SPUR BIT SHARPENING HSS SHARPENING C.T. SHARPENING UP TO 1-1 / 2 " DIA. - - - - - - $8.00 EA. . . . . . . . . . . . . . . . . . . . . . . . . . . $9.50 EA. 1 - 9 / 16 " TO 2 - 1 / 2 " - - $9.50 EA. . . . . . . . . . . . . . . . . . . . . . . . . . . $11.00 EA. 2 - 9 / 16 " TO 3 - 1 / 2 " - - $10.00 EA . . . . . . . . . . . . . . . . . . . . . . . . . . $12.50 EA. OVER 3 - 1 / 2" - - - - - - - -$14.00 EA .. . . . . . . . . . . . . . . . . . . . . . . . . . $16.00 EA. MULTI SPUR TIP REPLACEMENT - - - - - - - - -1 - 4 TIPS . . . . . . .$ 10.00 EA. TIP 5 + TIPS . . . . . . . . . . .$ 9.00 EA. TIP CHIP LIFTERS. . . . . . . . .$ 25.00 EA. TIP =========================================================================
STEEL MOULDER FEED WHEEL SHARPENING UP TO 2 " - - - - -$65.00 EA - - - - - - - - - -2 " TO 3 " - - - - - - - - - -$80.00 EA. OVER 3 " WIDE ADD $10.00 PER INCH OF WIDTH (STANDARD FEED WHEELS ONLY - OTHERS QUOTED UPON REQUEST) REMILLING GROOVES IN FEED WHEELS - - - - - - - - - - - -$60.00 EA. REHARDENING FEEDWHEELS - - - - - - - - - - - - - - - - - - - -$35.00 EA. =========================================================================
BANDSAW GUIDE WHEELS # 0 WHEELS - - - -$ 110.00 EA . . . . . . . . . . . . . . .# 1 WHEELS - - - -$ 120.00 EA. =========================================================================
BANDSAW GUIDE JAWS PLAIN JAWS C. T. JAWS # 0 - - $80.00 EACH SET OF 4 PCS....................0 - - $ 110.00 EACH SET OF 4 PCS. # 1 - - $90.00 EACH SET OF 4 PCS....................1 - - $ 120.00 EACH SET OF 4 PCS. RETIP BANDSAW GUIDE PRICE - - - - - -$ 10.00 PER END TANNEWITZ R - 84 AND R- 84A JAWS PLAIN AND CT ARE AVAILABLE BANDSAW THROAT PLATES - - - - -SQUARE $ 38.00 EA. ROUND $48.00 EA. =========================================================================
Page 14
PRICE LIST FOR BANDSAW BLADES AND ROLL STOCK ===================================================================
LENGTH WIDTH (IN FEET)--- 1 / 8 3 / 16 1 / 4 3 / 8 1 / 2 3 / 4
------------------------------------------------------------------------------------------------------------------------------------ 9 10.50 10.50 10.50 10.50 10.50 13.00
-------------------------------------------------------------------------------------------------------------------------------------- 10 11.00 11.00 11.00 11.00 11.00 13.00
-------------------------------------------------------------------------------------------------------------------------------------- 11 11.50 11.50 11.50 11.50 11.50 15.00
-------------------------------------------------------------------------------------------------------------------------------------- 12 12.00 12.00 11.50 11.50 11.50 15.00
-------------------------------------------------------------------------------------------------------------------------------------- 13 12.50 12.50 11.50 11.50 11.50 16.00
-------------------------------------------------------------------------------------------------------------------------------------- 14 13.00 13.00 12.50 12.50 12.00 16.00
-------------------------------------------------------------------------------------------------------------------------------------- 15 13.50 13.50 12.25 12.25 12.25 17.00
-------------------------------------------------------------------------------------------------------------------------------------- 16 14.00 14.00 13.00 13.50 14.00 18.00
-------------------------------------------------------------------------------------------------------------------------------------- 17 14.00 14.00 13.00 13.50 14.00 19.00
-------------------------------------------------------------------------------------------------------------------------------------- 18 15.00 15.00 13.50 14.50 14.50 20.00
-------------------------------------------------------------------------------------------------------------------------------------- 19 16.50 16.50 15.00 15.50 16.00 22.00
-------------------------------------------------------------------------------------------------------------------------------------- 20 17.00 17.00 15.00 15.50 16.00 22.00
-------------------------------------------------------------------------------------------------------------------------------------- 21 17.50 17.50 16.00 16.50 17.00 22.00
-------------------------------------------------------------------------------------------------------------------------------------- 22 18.00 18.50 16.00 17.50 17.00 22.00
-------------------------------------------------------------------------------------------------------------------------------------- FOR IN BETWEEN SIZES GO TO THE NEXT LONGER SIZE
ALL WOOD CUTTING BLADES UP TO 8' LONG - - -$9.00 EA STANDARD METAL CUTTING 64-1/2" X 1 / 2 - - -$10.00 EA
BANDSAW STOCK ROLL PRICES .025 OR .032 THICK
1 / 4 - - - -$125.00 3 / 8 - - - -$139.00 1 / 2 - - - -$167.00 3 / 4 - - - -$175.00
WELD PRICES
UP TO 1 / 2 WIDE - - - -$4.00 OVER 1 / 2 WIDE - - - -$5.00 BI-METAL BLADES - - - $10.00
SHARPENING CHARGE FOR BLADES UP TO 3 / 4 WIDE - - - -$4.50 OVER 3 / 4 WIDE - - - -$9.00
SHARPENING CHARGE FOR SPIRAL ROUTER BITS UP TO 1/2"DIA. 2 WING UPCUT OR DOWNCUT ...........$10.00 5/8"DIA. AND UP................................................$15.00 3 WING AND UP (ANYSIZE)..................................$15.00 SPIRAL COMPRESSION......2 FLUTE......$15.00 ......4FLUTE........$25.00
Page 15Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
NEW CARBIDE TIPPED SAWS (FLAT A.T.B. & T. CHIP) =========================================================================
DIAMETER
NO. TEETH 8" 10" 12" 14" 16" 18" =========================================================================
20 $70.25 72.75 $78.75 82.75 $87.00 $90.50 24 $77.00 78.75 $89.00 92.75 $95.25 $100.50 30 $92.50 95.00 $96.50 98.00 $102.50 $106.50 36 $100.00 102.00 $103.75 106.00 $110.00 $112.50 40 $104.75 106.25 $108.50 112.50 $118.25 $121.75 48 $114.25 116.00 $118.25 122.25 $128.25 $132.00 60 $128.25 129.75 $133.75 137.75 $139.25 $145.00 72 $143.00 144.50 $148.75 152.50 $156.50 $159.75 80 $163.50 165.50 $167.75 173.50 $177.00 $180.50 90 -------- ---------- $187.25 191.25 $195.00 $198.50 96 ------- --------- $194.25 198.25 $202.00 $206.00 100 -------- --------- $204.75 210.75 $214.50 $217.50
120 --------- ------- --------- 235.25 $243.00 $243.00
DADO HEADS
DADO SAWS------PER ABOVE SAW SCHEDULE
NEW DADO FILLERS:
1 / 16" 1 / 8" 1 / 4" ===================================================================
10” X 5/8 OR 1” BORE…. $34.50 $35.25 $47.25 12” X 1” BORE…………... $36.50 $37.00 $60.50 14” X 1” BORE…………. $41.25 $56.50 $68.25
(Providing filler blanks are available)
BORING CHARGES FOR NEW SAWS ONLY
UP TO 1” ..................................... $15.00
1” TO 1- 1 / 2 “................................ $20.00 1- 1 / 2” TO 2- 1 / 2 “....................... $25.00
Page 16
L W T a T04F T03SMG T10MG TL15 T08SMGmm mm mm mm
20.0 9.0 1.5 13195
24.0 9.0 1.5 14.0 1319730.0 9.0 1.5 14.0 1319940.0 9.0 1.5 26.0 1320050.0 9.0 1.5 26.0 13201
L W T a T08MF T03SMG T10MG TL15 T08SMGmm mm mm mm
80.0 13.0 2.2 60.0 12008 13841 13997 13755100.0 13.0 2.2 60.0 12009 30831 13998 13756120.0 13.0 2.2 60.0 12010 30832 13999 13757
L W T a T04F T03SMG T10MG TL15 T08SMG
mm mm mm mm
7.5 12.0 1.5 12001 13811 13963 13734 142258.6 12.0 1.5 131829.0 12.0 1.5 12043
9.6 12.0 1.5 12015 13850 14010 3083310.0 12.0 1.5 1316510.5 12.0 1.5 13167
11.0 12.0 1.5 1316811.6 12.0 1.5 1318313.0 12.0 1.5 13170
13.6 12.0 1.5 1318514.6 12.0 1.5 1318615.0 12.0 1.5 12003 13819 13972 13741 14232
15.7 12.0 1.5 1317216.0 12.0 1.5 1320317.0 12.0 1.5 13173
18.0 12.0 1.5 13174
19.0 12.0 1.5 1317520.0 12.0 1.5 12004 13823 13977 13745 1423525.0 12.0 1.5 12025 13853 14013 13766
25.0 12.0 1.5 14.0 12011 13843 14001 1375930.0 12.0 1.5 14.0 12005 13828 13982 13749 1423935.0 12.0 1.5 26.0 13208
40.0 12.0 1.5 26.0 12014 13847 14006 13763 1425550.0 12.0 1.5 26.0 12006 13834 13987 13753 1424460.0 12.0 1.5 26.0 12007 13839 13994 13754 14248
Standard reversible knivesStandard WendeschneidplattenPlaquettes reversibiles standardColtelli reversibili standardCuchillas reversibles standard
35°
Page 17Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Standard reversible knivesStandard WendeschneidplattenPlaquettes reversibiles standardColtelli reversibili standardCuchillas reversibles standard
L W T d T08MF T04F T03SMG T10MG TL15
mm mm mm mm
10.5 10.5 1.5 35° 4.0 13259 13863 14027 1376912.0 12.0 1.5 35° 4.0 12002 13815 13968 1373713.0 13.0 2.5 35° 4.0 13328
17.0 17.0 2.0 35° 3.0 16565 1656417.0 17.0 2.0 35° 4.0 13266 13265 13864 30830 1377019.0 19.0 2.0 35° 4.0 13264 30838 30827 30826
10.5 10.5 1.5 35° 4034313.0 13.0 2.5 30° 1332413.6 13.6 2.0 30° 1329913.6 13.6 2.0 45° 37522
14.0 14.0 1.2 30° 1329514.0 14.0 1.7 22° 1329714.0 14.0 1.7 30° 1330714.0 14.0 2.0 30° 13273 13260 13865 14028 13771
14.0 14.0 1.2 30° 13303
14.3 14.3 2.5 35° 1332914.6 14.6 2.5 30° 1331415.0 15.0 2.5 30° 13315
14.0 14.0 2.0 30° 1327615.0 15.0 2.5 30° R=50 4389515.0 15.0 2.5 30° R=150 13320
15.0 15.0 2.5 30° 44289
14.0 14.0 2.0 30° 44486
21.0 21.0 5.5 40° 22695
For Holz-Her system*
Page 18
Page 19Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 20
Page 21Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 22
Fuller Countersinks · Counterbores · Tapered Drills · Plug Cutters · Step Drills · Stop Collars
Type �C� Four Flute Countersinks
C4
Ta r
STCdDlac
Shown abThis combthrough thother typeordinary sown hole othread alloScrew Cha Drills are on pages 3of screw, u
For left haL to stock Price inclustop collarkeys. Also see Taper Po
C8
Stock Sizes
Stock Number
Cutting Diameter
Drill Hole Size
Overall Length
C2 1/4 5/64 3/4 C3 1/4 3/32 3/4 C4 5/16 7/64 7/8 C44 5/16 1/8 7/8 C65 5/16 9/64 7/8 C410 5/16 5/32 7/8 C411 5/16 11/64 7/8 C43 5/16 3/16 7/8 C56 3/8 3/32 7/8 C57 3/8 7/64 7/8
* C5 3/8 1/8 7/8 * C6 3/8 9/64 7/8
Used to countersink and counterbore for heads of screws in woods,plastics and non-ferrous materials. Heat treated for long tool life. (see explanation on page 3 and size recommendations on page 4)
he countersink is held in place with two hex-socket screws and is easily djustable up and down the drill so only one countersink and length of drill isequired for one screw size.
C92 * C7 3/8 5/32 7/8 * C8 3/8 11/64 7/8 * C9 3/8 3/16 7/8
C913 3/8 13/64 7/8 C97 3/8 7/32 7/8 C105 7/16 5/32 7/8 C1011 7/16 11/64 7/8 C103 7/16 3/16 7/8
* C10 7/16 13/64 7/8 C1014 7/16 7/32 7/8
hown above Mounted on a Taper Point Drill with Stop Collar: his combination of Tapered Drill and Countersink, drills, ountersinks and Counterbores in one quick operation. Makes riving screws easier and assures the best possible holding power. esigned for clean cutting and hardened for long wear. Complete
ist of Taper Point Drills shown on page 6 & 7. Stop Collar (shown bove mounted on Type �C� Countersink) can be furnished to ontrol depth of cut. Stop Collar sizes are shown on page 6.
C16
C104 7/16 1/4 7/8 C122 1/2 1/8 7/8
ove Mountedination can bee material for s of screws. Thtraight twist drr by using cowing shank ofrt on page 4 f
not included u6 through 42.se matching P
Special snd cutting add number.
des two hex-s. See page 118
page 117 forint Drills (an
C129 1/2 9/64 7/8 C125 1/2 5/32 7/8 C1211 1/2 11/64 7/8
on a Brad or Regular Poi used to drill and countersiscrews and bolts or to drill e Countersinks can also beills allowing the screw thre
rrect pilot drill size for root screw to force its way intoor screw sizes.
nless specified. Types and To cut wood plug to fit inlug Cutter shown on page
izes - Quotation on request 50% to prices shown in pr
ocket set screws. Does not &119 for replacement set
all sizes of Countersinksd Stop Collars if required
C244
C324
nt Drill: nk clearance pilot holes for mounted on ad to cut its diameter of the wood. See
sizes are shown hole over head 9.
. ice list and add
include drill or screws and hex
mounted on ).
* C92 1/2 3/16 7/8 * C102 1/2 13/64 7/8 * C12 1/2 7/32 7/8
C1415 1/2 15/64 7/8 * C14 1/2 1/4 7/8
C145 5/8 5/32 1-1/16 * C143 5/8 3/16 1-1/16
C167 5/8 7/32 1-1/16 * C16 5/8 1/4 1-1/16
C1617 5/8 17/64 1-1/16 * C169 5/8 9/32 1-1/16
C1619 5/8 19/64 1-1/16 * C18 5/8 5/16 1-1/16
C243 3/4 3/16 1-1/8 C247 3/4 7/32 1-1/8 C244 3/4 1/4 1-1/8 C245 3/4 5/16 1-1/8 C20 3/4 21/64 1-1/8 C24 3/4 3/8 1-1/4 C284 7/8 1/4 1-1/4 C285 7/8 5/16 1-1/4 C286 7/8 3/8 1-1/4 C287 7/8 7/16 1-3/8 C324 1 1/4 1-3/8 C326 1 3/8 1-3/8 C328 1 1/2 1-1/2
*
Page 23Hick
Indicates most popular sizes contained in sets.
ory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
COUNTERBORES AND COUNTERSINKS
STYLE 5 ADJUSTABLE COUNTERBORES
For Flat bottom holes 3" Long Twist 1/2" Shank
Split Shank 4-1/2" Overall
Stock No Size10501...................................... 3/8 X 1/8 10502.................................... 3/8 x 5/32 10503.................................... 3/8 x 3/16 10504.................................. 7/16 x 5/32 10505.................................. 7/16 x 3/16 10506.................................. 7/16 x 7/32 10507.................................... 7/16 x 1/4 10508...................................... 1/2x1/8 10509.................................... 1/2 x 5/32 10510.................................. 1/2x11/64 10511 .................................... 1/2x3/16 10512.................................. 1/2 x 13/64 10513.................................... 1/2 x 7/32 10514...................................... 1/2 x 1/4 10516.................................. 9/16x3/16 10517.................................. 9/16x7/32 10518.................................... 9/16 x 1/4 10519.................................. 9/16 x 9/32 10520.................................... 5/8 x 5/32 10521 .................................... 5/8x3/16 10522.................................... 5/8 x 7/32 10523......................................5/8 x 1/4 10524.................................... 5/8 x 9/32 10525.................................... 5/8 x 5/16 10526.................................. 11/16x1/4 10527................................ 11/16x9/32 10528................................ 11/16x5/16 10529....................................3/4x3/16 10530.................................... 3/4 x 7/32 10531 ......................................3/4 x 1/4 10532.................................... 3/4 x 9/32 10533....................................3/4 x 5/16 10534......................................3/4 x 3/8 10535................................ 13/16 x 3/16 10536................................. 13/16 x 1/4 10537................................ 13/16 x 9/32 10538................................ 13/16 x 5/16 10539....................................7/8x3/16 10540....................................7/8 x 7/32 10541 ......................................7/8x1/4 10542....................................7/8 x 5/16 10543......................................7/8 x 3/8 10544......................................... 1 x1/4 10545........................................1 X5/16 10546......................................... 1 x3/8 10547...................................1-1/8 x 1/4 10548................................. 1-1/8x5/16 10549...................................1-1/8x3/8 10550...................................1-1/4 x 1/4 10551.................................. 1-1/4x5/16 10552...................................1-1/4 x 3/8
Countersink drills are not included in above prices. Countersink drill held with split shank and set screw.
Tapered head to bore for Flat head screws
3" Long Twist 1/2" Shank
Split shank 4-1/2" Overall
Stock No. Size15101 ......................................3/8 x 1/8 15102....................................3/8 x 5/32 15103....................................3/8x3/16 15104.................................. 7/16x5/32 15105.................................. 7/16x3/16 15106.................................. 7/16x7/32 15107....................................7/16x1/4 15108...................................... 1/2 x 1/8 15109.................................... 1/2 x 5/32 15110.................................. 1/2x11/64 15111..................................... 1/2x3/16 15112.................................. 1/2x13/64 15113.................................... 1/2 x 7/32 15114...................................... 1/2x1/4
Countersink drills are not included in above prices. Countersink drill held with split shank and set screw.
STYLE 5C SHORT LENGTH COUNTERSINKS
Tapered Head to bore for Flat
head screws
1-1/2" Long Twist 1-1/2" Shank
Split Shank 3" Overall
Stock No Size15201 1/2x3/16 15202 1/2x7/32 15203 1/2x1/4
Countersink drills are not included in above prices. Countersink drill held with split shank and set screw.
Order by Stock Number
For Flat bottom holes
3" Long Twist 4-1/2" Overall 7/16-14 Shank
Stock No SizeRight Hand15401.......................................3/8x1/8 15402 ....................................3/8 x 5/32 15403...................................... 3/8 x 3/16 15404 ..................................7/16 X 5/32 15405 ..................................7/16 x 3/16 15406 ..................................7/16x7/32 15407 ....................................7/16 x 1/4 15408 .................................... 1/2 x 5/32 15409 .................................... 1/2x3/16 15410 .................................... 1/2 x 7/32 15411 ..................................... 1/2x1/4 15412 ....................................5/8 x 3/16 15413.................................... 3/4x3/16 15414 ....................................3/4 x 7/32 15415...................................... 3/4x1/4 Left Hand15416 ................................... 3/8 x 5/32 15417.................................... 3/8 x 3/16 15418...................................7/16x3/16 15419.................................... 1/2 x 5/32 15420.................................... 1/2x3/16 15421 ................................... 1/2x7/32 15422...................................... 1/2 x 1/4 15423.................................... 5/8x3/16 15424.................................... 3/4x3/16 15425.................................... 3/4 x 7/32 15426...................................... 3/4 x 1/4
Countersink drills are not included in above prices.
STYLE 514C SCREW SHANK COUNTERSINKS
Taper Head
3" Twist 4-1/2" Overall 7/16-14 Shank
SizeStock No Right Hand15427.................................... 3/8x3/16 15428.................................... 1/2x3/16 15429.................................... 1/2 x 7/32 15430...................................... 1/2 x 1/4 Left Hand15431 .................................... 3/8x3/16 15432.................................... 1/2x3/16 15433.................................... 1/2 x 7/32 15434...................................... 1/2 x 1/4
Countersink drills are not included in above prices.
STYLE 5C ADJUSTABLE COUNTERSINKS
STYLE 514 SCREW SHANK COUNTERBORES
Page 24
STYLE 5A ADJUSTABLE COUNTERBORES
STYLE 5E SOLID COUNTERSINKS
STYLE 814 SCREW SHANK TAPER COUNTERSINKS
5/8" dia. and under are 1-1/2" Overall
Larger sizes are 2" Overall Set Screw Adjustment
Stock No.15301 .................................... 3/8x3/16 15302 .................................... 1/2 x 3/16 15303.................................... 1/2 x 7/32 15304 ...................................... 1/2 x 1/4 15305 ......................................5/8 x 1/4 15306.................................... 5/8x5/16 15307 ......................................3/4 x 1/4 15308 ....................................3/4 x 5/16 15309 ......................................7/8 x 1/4 15310 ....................................7/8 x 5/16 15311 ......................................7/8x3/8 15312 ....................................7/8 x 7/16 15313 ..........................................1 x1/4 15314 ........................................1 X5/16 15315 ..........................................1 X3/8 15316 ........................................1 X7/16 15317 ......................................... 1 x1/2 15318 ................................. 1-1/8x5/16 15319 ...................................1-1/8 x 3/8 15320 ................................. 1-1/8x7/16 15321.................................... 1-1/8x1/2 15322.................................. 1-1/4 x 5/16 15323....................................1-1/4 x 3/8 15324 .................................1-1/4x7/16 15325....................................1-1/4 x 1/2 15326....................................1-3/8 x 3/8 15327..................................1-3/8 x 7/16 15328....................................1-3/8 x 1/2 15329....................................1-1/2x3/8 15330..................................1-1/2 x 7/16 15331 ...................................1-1/2x1/2 15332 .................................1-1/2x9/16 15333....................................1-1/2 x 5/8 15334....................................1-5/8 x 1/2 15335....................................1-3/4 x 1/2 15336....................................1-7/8 x 1/2 15337.......................................... 2 x 1/2
Drills are not included in above prices.
STYLE 5D SOLID COUNTERBORES
Spur Cut 1 -1/2" Long Small Dia. 1/2x2" Shank 5-1/2" Overall
Stock No Size155004.................................. 3/8 X 3/16 15501 ..................................... 1/2x3/16 15502..................................... 1/2 x 7/32 15503...................................... 1/2 x 1/4
Bevel Cut 1-1 /2" Long Small Dia. 1/2x2" Shank 5-1/2" Overall
Stock No15600.................................... 3/8X3~/16 15601 .................................... 1/2x3/16 15602.................................... 1/2 x 7/32 15603...................................... 1/2x1/4
TAPER COUNTERSINKS
STYLE 4 TAPER SHELL COUNTERSINKS
1 -1/4" Overall Set Screw Adjustment
Stock No. Size10401 .................................... 3/8x3/16 10402 ...................................... 1/2 x 1/8 10403.................................... 1/2x9/64 10404.................................... 1/2 x 5/32 10405.................................. 1/2x11/64 10406 .................................... 1/2 x 3/16 10407 .................................. 1/2 x 13/64 10408 .................................... 1/2 x 7/32 10409 ...................................... 1/2 x 1/4 10410 ......................................5/8x1/4 10411 ....................................5/8x5/16 10412 ....................................3/4x5/16 10413 ......................................3/4 x 3/8
Drills not included in above prices.
STYLE 8 TAPER COUNTERSINKS
1/2" Shank 3" Overall Split Shank & Set Screw Adjustment
Stock No. Size10801.....................................3/8x3/16 10802 .................................... 1/2 x 3/32 10803 ......................................1/2 x 1/8 10804 .................................... 1/2 x 9/64 10805 .................................... 1/2 x 5/32 10806 .................................. 1/2 x 11/64 10807 .................................... 1/2x3/16 10808 .................................. 1/2 x 13/64 10809 .................................... 1/2 x 7/32 10810 ..................................... 1/2 x 1/4 10811 ..................................9/16x3/16 10812...................................9/16 x 7/32 10813 ....................................9/16x1/4 10814 ....................................5/8 x 7/32 10815...................................... 5/8 x 1/4 10816...................................5/8 x 19/64 10817 ....................................5/8 x 5/16 10818.....................................3/4x3/16 10819...................................... 3/4 x 1/4 10820.................................... 3/4 x 5/16 10821 ..................................... 3/4x3/8 Countersink drills are not included in above prices.
3" Overall 7/16-14 Shank
Right Hand
Stock No. Size81401 ..................................... 1/2 x1/8 81402.................................... 1/2 x 5/32 81403.................................... 1/2x3/16 81404.................................... 1/2 x 7/32 81405...................................... 1/2x1/4
Left Hand and 5/16-18 Shank Countersinks on Application. Countersink drills are
not included in above prices.
STYLE 184 MULTI SPUR COUNTERBORES
Stock No. Size18401 ......................................... 1 x1/2 18402................................... 1-1/8 x 1/2 18403................................... 1-1/4 x 1/2 18404...................................1-3/8 x 1/2 18405...................................1-1/2 x 1/2 A 18406...................................1-5/8 x 1/2 18407................................... 1-3/4x1/2 18408 ...................................1-7/8 x 1/2 18409 ......................................... 2 x 1/2 18410 ...................................2-1/8x1/2 18411 ...................................2-1/4x1/2 18412 ...................................2-1/2 x 1/2
Drills are not included in above prices
CARBIDE TIPPED COUNTERSINKS
STYLE 5CT COUNTERBORES
CARBIDE TIPPED
3" Twist 4-1/2" Overall 1/2x1-1/2" Shank Split
Shank & Set Screw
Stock No. Size15701 ....................................3/8 x 3/16 15702.................................... 1/2x3/16 I 15703.................................... 1/2 x 7/32 15704...................................... 1/2 x 1/4 Countersink drills are not included in above prices.
Page 25Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
STYLE 5CT TAPER POINT COUNTERSINKS
COUNTERSINK DRILLS
STYLE 5-7 COUNTERSINK DRILLS
CARBIDE TIPPED
3" Twist 4-1/2" Overall 1/2x1-1/2" Shank
Split Shank & Set Screw
Stock No. Size15801 ................................... 3/8 X 3/16 15802.................................... 1/2 X 3/16 15803.................................... 1/2 x 7/32 15804...................................... 1/2 x 1/4
Countersink drills are not included in above prices.
STYLE 514CT COUNTERBORES
CARBIDE TIPPED
3" Twist 4-1/2" Overall 7/16-14 Shank
Right HandStock No. Size15901 ................................... 3/8x3/16 15902..................................... 1/2 x 3/16 15903.................................... 1/2 x 7/32 15904...................................... 1/2x1/4
Left Hand15905.................................... 3/8 x 3/16 15906.................................... 1/2 x 3/16 15907.................................... 1/2 x 7/32 15908...................................... 1/2 x 1/4
Countersink drills are not included in above prices.
STYLE 4CT COUNTERSINKS
CARBIDE TIPPED
1-1/4" Overall Set Screw Adjustment
Stock No. Size14401.................................... 1/2x3/16 14402.................................... 1/2 x 7/32 14403...................................... 1/2 x 1/4
Countersink drills are not included in above prices.
STYLE 5 COUNTERSINK DRILLS
2-1/2" Long Twist
Stock No. Size50101............................................. 3/32 50102............................................... 1/8 50103............................................. 5/32 50104........................................... 11/64 50105............................................. 3/16 50106............................................. 13/64 50107............................................. 7/32 50108........................................... 15/64 50109............................................... 1/4 50110........................................... 17/64 50111............................................. 9/32 50112........................................... 19/64 50113............................................. 5/16 50114........................................... 11/32 50115... ...3/8
STYLE 5HS COUNTERSINK DRILLS
HIGH SPEED STEEL
2-1/2" Long Twist 6" Overall
Stock No. Size50201 ............................................... 1/8 50202............................................. 5/32 50203........................................... 11/64 50204.............................................3/16 50205........................................... 13/64 50206............................................. 7/32 50207............................................... 1/4 50208........................................... 17/64 50209............................................. 9/32 50210........................................... 19/64 50211 .............................................5/16 50212............................................... 3/8
STYLE 5HSLH COUNTERSINK DRILLS
3" Long Twist 7" Overall
Stock No. Size6" Overall 50701 ............................................3/16 50702............................................. 7/32 50703................................................. 1/4
STYLE 5-7BPHS COUNTERSINK DRILLS
HIGH SPEED STEEL Brad
Point
3" Long Twist 7" Overall
Stock No. Size50704............................................ 3/16 50705............................................ 7/32 50706............................. .. 1/4
STYLE 5-8 COUNTERSINK DRILLS
4" Long Twist 8" Overall
Stock No. Size50801............................................... 3/16 50802............................................ 7/32 50803........................... .. 1/4
STYLE 5-8BPHS COUNTERSINK DRILLS
STYLE 8CT COUNTERSINKS
CARBIDE TIPPED
3" Overall 1/2 x 1-1/2" Shank Split Shank & Set Screw
Stock No. Size 18801.................................... 1/2x3/16 18802.................................... 1/2 x 7/32 18803...................................... 1/2 x 1/4
Countersink drills are not included in above prices.
HIGH SPEED STEEL
Left Hand 2-1/2" Long Twist 6" Overall
Stock No. Size50213............................................ 3/16 50214............................................ 7/32 50215... ..1/4
HIGH SPEED STEEL
Brad Point
4" Long Twist 8" Overall
Stock No. Size50804 ............................................3/16 50805 ............................................ 7/32 50806 ......... ..1/4
Page 26
Page 27Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 28
Page 29Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 30
MH-20 BRAD POINT DRILL SET
CARBON STEEL
This set contains one each of the following sizes of drills: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/ 7/8",
and 1". Sizes 7/16" and under can be used 1 in 3/8" chucks. 1/2" and over have shanks to fit 1/2" chucks. Each set is furnished with a solid mahogany case.
12 Drills with Case
MH-21 BRAD POINT DRILL SET
HIGH SPEED STEEL This set contains one each of the following sizes of drills: 1/8", 5/ 32", 3/16", 7/32", 1/4", 5/16", 3/8", 7/16", and 1/2". Sizes 5/16 thru 1/2" have 1/4" shanks. Stop collars are fur-nished for each of the above sizes with three Hex Wrenches. These are cased in a fitted Solid Mahogany Case.
21 Piece Set With Case
STYLE 12 SCREW SHANK DRILL POINT DRILLS
CARBON STEEL
3" Long Twist 4-1/2" Overall 7/16-14 Shank
Stock No. Stock No. SIZE Right Hand Left Hand1/8................... 12001R 3/16 ................. 12002R 7/32 ................. 12003R 1/4................... 12004R 12004L 9/32 ................. 12005R 5/16 ................. 12006R 12006L 11/32 ............... 12007R 12007L 3/8 ................... 12008R 12008L 7/16 ................. 12009R 12009L 15/32 ............... 12010R 1/2 ................... 12011R 12011L 9/16 ................. 12012R 5/8 ................... 12013R 3/4 ................... 12014R
HIGH SPEED STEEL
3" Long Twist 4-1/2" Overall 7/16-14 Shank
Stock No. Stock No.Right Hand Left Hand
1/4 ...................... 12101R 12101L 9/32 .................... 12102R 12102L 5/16 .................... 12103R 12103L 11/32 .................. 12104R 12104L 3/8 ...................... 12105R 12105L 25/64 .................. 12106R 12106L 7/16 .................... 12107R 12107L 1 /2 . . . . . . 12108R 12108L
STYLE 14 SCREW SHANK BRAD POINT DRILLS
CARBON STEEL
3" Long Twist 4-1/2" Overall
7/16-14 Shank
Stock No. Stock No.Right Hand Left Hand
1/8 ...................14001R 14001L 5/32..................14002R 14002L 3/16..................14003R 14003L 7/32.................. 14004R 14004L 1/4.................... 14005R 14005L 17/64................14006R 14006L 9/32..................14007R 14007L 5/16.................. 14008R 14008L 11/32................14009R 14009L 3/8....................14010R 14010L 25/64................14011R 14011L 13/32................14012R 14012L 7/16..................14013R 14013L 29/64................14014R 14014L 15/32................ 14015R 14015L 1/2.................... 14016R 14016L 33/64................ 14017R 14017L 9/16..................14018R 14018L 5/8 ...................14019R 14019L 11/16................14020R 14020L 3/4.................... 14021R 14021L 7/8.................... 14022R 14022L 1 .. .. 14023R 14023L
HIGH SPEED STEEL
3" Long Twist 4-1/2" Overall 7/16-14 Shank
Stock No. Stock No.Right Hand Left Hand
3/16 .................14101R 14101L 7/32 .................14102R 14102L 6MM................. 141022R 141022L 1/4 ................... 14103R 14103L 9/32 .................14104R 14104L 5/16 ................. 14105R 14105L 8MM................. 141053R 141053L 11/32 ............... 14106R 14106L 3/8 ................... 14107R 14107L 25/64 ............... 14108R 14108L 10MM...............1410800R 1410800L 7/16 .................14109R 14109L 29/64 ............... 14110R 14110L 12MM............... 1411021R 1411021L 1/2 ................... 14111R 14111L 13MM............... 1411104R 1411104L 33/64 ...............141111R 141111L 9/16 ................. 14112R 14112L 5/8 ................... 14113R 14113L 11/16 ...............141131R 141131L 3/4 ................... 14114R 14114L 13/16 ...............141141R 141141L 7/8 ................... 14115R 14115L 1 .. .. 14116R 14116L
STYLE 14A SCREW SHANK
BRAD POINT DRILLS
STYLE 12HS SCREW SHANK DRILL POINT DRILLS
STYLE 14HS SCREW SHANK BRAD POINT DRILLS
2", 9/16", 5/8", 3/4"
CARBON STEEL
2-1/4" Twist 3-1/2" Overall 7/16-14 Shank
1/49/32 5/16 3/8 25/647/16 29/641/2
Stock No.Right Hand14024R 14025R 14026R 14027R 14028R 14029R 14030R 14031R
Stock No.Left Hand
14024L 14025L 14026L 14027L 14028L 14029L 14030L 14031L
Page 31Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
STYLE 14AHS SCREW SHANK BRAD POINT DRILLS
HIGH SPEED STEEL
2-1/4" Twist 3-1/2" Overall 7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand6MM................ 141170R 141170L 1/4................... 14117R 14117L 9/32................. 14118R 14118L 5/16................. 14119R 14119L 8MM................ 141191R 141191L 3/8................... 14120R 14120L 25/64............... 14121R 14121L 10MM.............. 141212R 141212L 7/16................. 14122R 14122L 12MM.............. 1412201R 1412201L 1/2................... 14123R 14123L 13MM.............. 1412301R 1412301L 5/8................... 14124R 14124L 3/4................... 14125R 14125L
STYLE 14B SCREW SHANK BRAD POINT DRILLS
CARBON STEEL
1 -3/4" Long Twist 3" Overall 7/16-14 Shank
Stock No.Right Hand14032R 14033R 14034R 14035R 14036R 14037R 14038R 14039R
HIGH SPEED STEEL
1 -3/4" Long Twist 3" Overall 7/16-14 Shank
Stock No. Stock No.Right Hand Left Hand
1/4 ................... 14126R 14126L 9/32 .................14127R 14127L 5/16 .................14128R 14128L 3/8 ...................14129R 14129L 25/64 ...............14130R 14130L 7/16 .................14131R 14131L 1/2 ................... 14132R 14132L 5/8 ...................14133R 14133L 3/4... .. 14134R 14134L
STYLE 14ES EXTENDED SCREW SHANK BRAD
POINT DRILLS
CARBON STEEL
1 -1/2" Long Twist 4-1/8" Overall 7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand1/4 ................... 14040R 14040L 5/16 .................14041R 14041L 3/8 ...................14042R 14042L 7/16 .................14043R 14043L 1/2 ...................14044R 14044L
STYLE 14ES-L
Stock No. Stock No.SIZE Right Hand Left Hand1/4................... 14045R 14045L 5/16................. 14046R 14046L 3/8................... 14047R 14047L 7/16................. 14048R 14048L 1/2... .. 14049R 14049L
STYLE 14ESHS EXTENDED STYLE 14BHS SCREW SHANK BRAD POINT DRILLS SCREW SHANK BRAD
POINT DRILLS
HIGH SPEED STEEL
1 -1/2" Long Twist 4-1/8" Overall 7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand1/4................... 14135R 14135L 5/16 ................. 14136R 14136L 3/8 ...................14137R 14137L 25/64 ............... 14138R 14138L 7/16 .................14139R 14139L 1/2... .. 14140R 14140L
STYLE14ESHS-L
1 -7/8" Twist 4-1 /8" Overall
Stock No. Stock No.SIZE Right Hand Left Hand1/4 ................... 14141R 14141L 5/16 ................. 14142R 14142L 3/8 ...................14143R 14143L 25/64 ...............14144R 14144L 7/16 ................. 14145R 14145L 1/2 ...................14146R 14146L
STYLE 14R SCREW SHANK BRAD POINT DRILLS
HIGH SPEED STEEL
1 -5/8" Long Twist 2-1/2" Overall 7/16-14 Shank
Stock No.Left Hand 14032L 14033L 14034L 14035L 14036L 14037L 14038L 14039L
Stock No. Stock No.SIZE Right Hand Left HandSIZE
1/4 9/32 5/16 3/8 25/64 7/16 29/64 1/2
1/4 ................... 14147R 14147L 9/32..................14148R 14148L 5/16 ................ 14149R 14149L 11/32............... 14150R 14150L 3/8 ...................14151R 14150L 25/64................14152R 14152L 7/16..................14153R 14153L 1/2 ...................14154R 14154L 9/16................. 14155R 14155L 5/8... ... 14156R 14156L
Page 32
3" Long Twist 4-1/2" Overall 7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand6MM................. 14200R 14200L 1/4 ...................14201R 14201L 9/32.................. 14202R 14202L 5/16 .................14203R 14203L 8MM.................142031R 142031L 3/8 ...................14204R 14204L 25/64 ............... 14205R 14205L 10MM...............142051R 142051L 7/16 ................. 14206R 14206L 12MM............... 142064R 142064L 1/2 ................... 14207R 14207L 13MM...............1420703R 1420703L 5/8 ...................14208R 14208L 3/4 ...................14209R 14209L 1"... .. 14210R 14210L
STYLE 14ACT SCREW
SHANK BRAD POINT DRILLS 2-1/4" Twist 3-1/2" Overall
7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand1/4 ................... 14211R 14211L 5/16 ................. 14212R 14212L 3/8 ................... 14213R 14213L 25/64 ............... 14214R 14214L 7/16 ................. 14215R 14215L 1/2 ................... 14216R 14216L
STYLE 29
Size Stock No.1/64................................................29001 1/32................................................29002 3/64................................................29003 1/16................................................29004 5/64................................................29005 3/32................................................29006 7/64................................................29007 1/8..................................................29008 9/64................................................29009 5/32................................................29010 11/64..............................................29011 3/16................................................29012 13/64..............................................29013 7/32................................................29014 15/64..............................................29015 1/4..................................................29016 17/64..............................................29017 9/32................................................29018 19/64..............................................29019 5/16................................................29020 21/64..............................................29021 11/32..............................................29022 23/64..............................................29023 3/8..................................................29024 25/64..............................................29025 13/32..............................................29026 27/64..............................................29027 7/16................................................29028 29/64.............................................. 29029 15/32.............................................. 29030 31/64.............................................. 29031 1/2... ....................29032
STYLE 29LH
LENGTH Stock No. OVERALL
.................................................... 3/4" 29002L............................................ 1-3/8" 29003L............................................ 1-3/4" 29004L............................................ 1-7/8" 29005L.................................................. 2" 29006L ........................................... 2-1/4" 29007L ........................................... 2-5/8" 29008L ........................................... 2-3/4" 29009L ........................................... 2-7/8" 29010L ........................................... 3-1/8" 29011L ........................................... 3-1/4" 29012L ........................................... 3-1/2" 29013L ........................................... 3-5/8" 29014L ........................................... 3-3/4" 29015L ........................................... 3-7/8" 29016L ................................................. 4" 29017L ........................................... 4-1/8" 29018L ........................................... 4-1/4" 29019L ........................................... 4-3/8" 29020L ........................................... 4-1/2" 29021L ........................................... 4-5/8" 29022L ........................................... 4-3/4" 29023L ........................................... 4-7/8" 29024L ................................................. 5" 29025L ........................................... 5-1/8" 29026L ........................................... 5-1/4" 29027L ........................................... 5-3/8" 29028L ........................................... 5-1/2" 29029L ........................................... 5-5/8" 29030L ........................................... 5-3/4" 29031L ........................................... 5-7/8" 29032L .. ... 6"
STYLE 14ESCT EXTENDED SCREW SHANK BRAD
POINT DRILLS 1 -7/8" Long Twist 4-1/2" Overall
7/16-14 Shank
Stock No. Stock No.SIZE Right Hand Left Hand1/4 ................... 14217R 14217L 5/16 ................. 14218R 14218L 3/8 ................... 14219R 14219L 25/64 ............... 14220R 14220L 7/16................. 14221R 14221L 1/2................... 14222R 14222L
GENERAL PURPOSE JOBBERS DRILL SETS
Complete with folding metal case
HIGH SPEED STEEL
Number of Drills
JS13M.................................... 13 JS21M....................................21 JS29M... ......29
STYLE 14CT SCREW SHANK BRAD POINT DRILLS
STYLE 29 GENERAL PURPOSE
JOBBER LENGTH DRILLS
STYLE 29LH LEFT HAND
JOBBER LENGTH DRILLS
CARBIDE TIPPED HIGH SPEED STEEL
CARBIDE TIPPED
CARBIDE TIPPED
Stock No
Page 33Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 34
Page 35Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 36
Page 37Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 38
Page 39Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 40
Page 41Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 42
Page 43Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 44
Page 45Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 46
Page 47Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 48
Page 49Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 50
Page 51Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 52
Page 53Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 54
Page 55Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 56
Page 57Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Page 58
Page 59Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
11-00 Single & Double Edge - HighSpeed Steel O Flute Straight
PART # CED CEL SHK DIA OAL
10-06 1⁄4 3⁄4 1⁄4 21⁄8
10-07 1⁄4 1 1⁄4 23⁄8
10-78 1⁄4 11⁄4 1⁄4 25⁄8
10-18 5⁄16 1 5⁄16 23⁄8
10-11 3⁄8 1 1⁄2 21⁄2
10-13 1⁄2 11⁄4 1⁄2 23⁄4
10-00 Single Edge - High SpeedSteel O Flute Straight
Combines an open flute design withsingle edge geometry to provide opti-mum chip removal at fast feed rates.Excellent for hand-fed operations.
■ Usage ABS, polycarbonate, polyethylene, PVC,PVC, polypropylene, polystyrene, extrudedacrylic, HDPE, UHMW, and natural wood
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
10-00 1⁄163⁄16 1⁄4 2
10-01 3⁄323⁄8 1⁄4 2
10-02 1⁄8 3⁄8 1⁄4 2
10-20 1⁄8 1⁄2 1⁄4 2
10-04 3⁄165⁄8 1⁄4 2
10-22 3⁄163⁄4 1⁄4 2
10-24 1⁄4 5⁄8 1⁄4 21⁄8
SW SP
PART # CED CEL SHK DIA OAL
11-00 3⁄16 5⁄8 1⁄4 2
11-02 1⁄4 3⁄4 1⁄4 21⁄8
11-72* 1⁄4 3⁄4 1⁄4 31⁄4
11-76* 1⁄4 3⁄4 1⁄4 33⁄4
11-04 1⁄4 1 1⁄4 23⁄8
11-78* 1⁄4 2 1⁄4 31⁄4
11-06 3⁄8 1 3⁄8 21⁄2
11-74* 3⁄8 1 3⁄8 31⁄2
*These tools are designed and toleranced for Air Routers with guide bushing.
Designed for cutting softer more flexibleplastics. Single edge for faster feedrates. Double edge for smoother finish.Excellent for hand-fed operations.
■ Usage ABS, polycarbonate,polyethylene, polystyrene,PVC, polypropylene extruded acrylic, HDPE, UHMW
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
11-01 1⁄8 1⁄2 1⁄4 2
11-75* 1⁄8 5⁄8 1⁄4 31⁄4
11-03 3⁄16 5⁄8 1⁄4 2
11-77* 3⁄16 3⁄4 1⁄4 31⁄4
11-05 1⁄4 3⁄4 1⁄4 21⁄8
11-71* 1⁄4 3⁄4 1⁄4 31⁄4
11-07 1⁄4 1 1⁄4 23⁄8
11-09 3⁄8 1 3⁄8 21⁄2
SP HP
SINGLE EDGE DOUBLE EDGE
Single Edge
Double Edge
Page 60
13-50 Single Edge - Carbide TippedStraight Opposite Shear
CW LWFP
PART # CED CEL SHK DIA OAL
13-52 1⁄2 21⁄4 1⁄2 41⁄4
13-55 3⁄4 2 3⁄4 4
Opposite shearing action tools designedto minimize chipping or tear out on bothsides of laminated or veneered stock.Excellent for sink cutouts.
■ Usage Wood composites, laminate, veneer & foam
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
13-53 1⁄2 11⁄4 1⁄2 23⁄4
13-54 1⁄2 11⁄2 1⁄2 3
13-50 1⁄2 2 1⁄2 4
SHEER ANGLE ≈ 3° - 6°
■ Usage Natural wood and aluminum
■ Material See Selection Guide - pg. 2 - 12SW A
15-00 Single Edge - High SpeedSteel Downcut Spiral
PART # CED CEL SHK DIA OAL
15-05 1⁄2 21⁄2 1⁄2 51⁄2
Designed to rout thick laminated stockof aluminum and wood and to makestraight through cuts in thick stock ofeither material.
PART # CED CEL SHK DIA OAL
15-03 1⁄2 21⁄4 1⁄2 51⁄4
HELIX ANGLE ≈ 18° - 32°
12-00 Double Edge - High SpeedSteel V Flute Straight
PART # CED CEL SHK DIA OAL
12-26 3⁄8 11⁄4 1⁄2 31⁄4
12-10 1⁄2 11⁄4 1⁄2 23⁄4
12-11 1⁄2 11⁄2 1⁄2 31⁄2
12-51 1⁄2 2 1⁄2 4
12-12 9⁄16 11⁄4 1⁄2 23⁄4
12-13 5⁄8 11⁄4 1⁄2 23⁄4
12-14 3⁄4 11⁄4 1⁄2 23⁄4
12-16 7⁄8 11⁄4 1⁄2 23⁄4
12-17 1 11⁄4 1⁄2 23⁄4
* These tools are designed and toleranced for Air Routers with guide bushing.
These V flutes are often selectedwhen a balanced tool is critical forsmooth finish. A universal tool used inmany environments. Excellent forhand-fed applications.
■ Usage Foam and natural wood
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
12-32 3⁄163⁄4 1⁄4 2
12-00 1⁄4 3⁄4 1⁄4 21⁄8
12-01 1⁄4 1 1⁄4 23⁄8
12-79* 1⁄4 1 1⁄4 31⁄4
12-35 1⁄4 1 1⁄2 21⁄2
12-37* 1⁄4 11⁄4 1⁄4 31⁄4
12-03 5⁄16 1 3⁄8 3
12-36 5⁄16 1 1⁄2 21⁄2
12-05 3⁄8 1 3⁄8 21⁄2
12-06 3⁄8 1 1⁄2 21⁄2
HW FP
Page 61Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Wood panels, vinyl coated panels, wallboard and aluminum layered materials
■ Material See Selection Guide - pg. 2 - 12CM
DW
18-00 Single Edge - High Speed SteelStraight Pilot
PART # CED CEL SHK DIA OAL
18-03 1⁄2 1 1⁄2 31⁄2
Straight flute tools with boring pointsand pilots are the workhorse of themobile home, modular home and RVindustries.
PART # CED CEL SHK DIA OAL
18-00 1⁄4 3⁄4 1⁄4 23⁄4
18-02 3⁄8 7⁄8 3⁄8 27⁄8
TITANIUM COATED
■ Usage Metal clad doors (15-50 and TIN15-50)Fiberglass doors (TIN15-50)
■ Material See Selection Guide - pg. 2 - 12D
15-50 Single Edge - High Speed SteelDor-Bits
PART # CED CEL SHK DIA OAL DOOR MACHINE
TIN15-52 1⁄2 21⁄4 1⁄2 51⁄4 RUVO
TIN15-53 1⁄2 21⁄2 1⁄2 51⁄2 RUVO
TIN15-54 1⁄2 21⁄2 1⁄2 5 ACE
TIN15-55* 1⁄2 21⁄2 1⁄2 51⁄2 FALCON
TIN15-57* 1⁄2 21⁄2 1⁄2 51⁄2 NORFIELD
TIN15-60 1⁄2 21⁄2 1⁄2 51⁄2 RUVO
TIN15-61* 1⁄2 21⁄2 1⁄2 51⁄2*Have Flats
Designed to rout steel doors.
PART # CED CEL SHK DIA OAL DOOR MACHINE
15-52 1⁄2 21⁄4 1⁄2 51⁄4 RUVO
15-53 1⁄2 21⁄2 1⁄2 51⁄2 RUVO
15-54 1⁄2 21⁄2 1⁄2 5 ACE
15-55* 1⁄2 21⁄2 1⁄2 51⁄2 FALCON
15-57* 1⁄2 21⁄2 1⁄2 51⁄2 NORFIELD
15-60 1⁄2 21⁄2 1⁄2 51⁄2 RUVO
15-61* 1⁄2 21⁄2 1⁄2 51⁄2
HELIX ANGLE ≈ 18° - 32° *Have Flats
TITANIUM COATED
■ Usage Metal clad or fiberglass doors
■ Material See Selection Guide - pg. 2 - 12D
15-75 Three Edge - High Speed SteelCNC Dor-Bits
PART # CED CEL SHK DIA OAL DOOR MACHINE
TIN15-75 1⁄2 3 1⁄2 6 KVAL
HELIX ANGLE ≈ 18°
Downcut tools designed specifically formachining metal clad doors in a CNCenvironment. The tool geometry facilitatespiercing steel and produces a superior cutfor door lites and hardware openings.
Page 62
■ Usage Aluminum and plywood sandwich panels,vinyl coated panels, wall board, drywalland layered material
■ Material See Selection Guide - pg. 2 - 12CM
DW
20-00 Single Edge - High Speed SteelDowncut Spiral Pilot
PART # CED CEL SHK DIA OAL
20-03 1⁄2 11⁄4 1⁄2 4
Spiral tools designed to push chipsaway from the operator in mobilehome and RV manufacturing plants.
PART # CED CEL SHK DIA OAL
20-00 1⁄4 3⁄4 1⁄4 3
20-02 3⁄8 1 3⁄8 37⁄16
HELIX ANGLE ≈ 21° - 38°
■ Usage Drywall cut outs
■ Material See Selection Guide - pg. 2 - 12CM
DW
20-10 Single Edge - High Speed SteelDrywall Bit
PART # CED CEL SHK DIA OAL
20-12 1⁄8 51⁄641⁄8 21⁄2
20-15 1⁄8 1 1⁄8 21⁄2
Spiral flute tools designed to make cutouts in drywall. Used in manufacturedhousing and on site construction.
PART # CED CEL SHK DIA OAL
20-10 3⁄16 1 1⁄4 31⁄4
20-11 1⁄8 3⁄4 1⁄8 21⁄2
HELIX ANGLE ≈ 30° - 41°
27-00 Single Edge - Solid CarbideLaminate Trim
■ Usage Trimming laminate counter tops andtrimming plastic parts
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL STYLE
27-03 1⁄4 3⁄8 1⁄4 11⁄2 Flush
27-04 1⁄4 3⁄8 1⁄4 11⁄2 7° Bevel/Flush
Designed to trim counter tops. Thepilot bears on the finished surface andacts as a guide to trim flush or with abevel. Available with boring point ifnecessary to plunge and rout.
PART # CED CEL SHK DIA OAL STYLE
27-00 1⁄4 1⁄4 1⁄4 11⁄2 Flush
27-01 1⁄4 1⁄4 1⁄4 11⁄2 7° Bevel
LW
Page 63Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
27-50 Double Edge - Solid CarbideLaminate Trim
■ Usage Trimming laminate counter topsand trimming plastic parts
■ Material See Selection Guide - pg. 2 - 12
Tools with a pilot designed to givea satin smooth finish when trimminglaminate counter tops.
PART # CED CEL SHK DIA OAL STYLE
27-50 1⁄4 7⁄161⁄4 15⁄8 Flush
LW
28-20 Solid CarbideDouble-Bearing Plastic Trim
■ Usage Trimming stacked sheets plastic & laminates
■ Material See Selection Guide - pg. 2 - 12
REPLACEMENT BEARING KITS FOR SERIES 28-20
Solid Carbide Double Bearing Plastic Trim Tool Kits
28-89 KIT for 28-20 Tool
28-88 KIT for 28-25 Tool
28-88 KIT for 28-30 Tool
Spirals designed to trim stacked sheetsof plastic in hand-fed applications. Theyuse a double bearing guide to ensuresmooth cutting action around a template.
PART # CED CEL SHK DIA OAL FLUTE
28-20 1⁄4 3⁄4 1⁄4 3 2
28-25 1⁄2 11⁄8 1⁄2 4 2
28-30* 1⁄2 11⁄8 1⁄2 4 3
HELIX ANGLE ≈ 11° - 30° * Up/Down Spiral Compression
SP HPDouble Edge
Three Edge
28-50 Carbide TippedFlush Trim
■ Usage Natural wood, wood composites,laminated and veneered
■ Material See Selection Guide - pg. 2 - 12
Designed to provide a smooth finishededge on dense, abrasive and laminatedmaterials. A ball bearing guide assistsfree cutting action. Excellent for hand-fedapplications.
PART # CED CEL SHK DIA OAL FLUTES REP. BEARING KIT
28-55 1⁄4 1 1⁄4 21⁄2 2 28-80
28-51 3⁄8 1⁄2 1⁄4 21⁄4 2 28-79
28-50 3⁄8 1 1⁄4 23⁄4 2 28-79
28-53 1⁄2 1⁄2 1⁄4 2 2 28-78
28-52 1⁄2 1 1⁄4 23⁄4 2 28-78
28-57 1⁄2 1 1⁄4 23⁄4 3 28-78
28-56 1⁄2 1 3⁄8 3 2 28-78
28-54 1⁄2 1 1⁄2 31⁄4 2 28-78
28-59 1⁄2 11⁄2 1⁄2 41⁄4 3 28-78
28-63 1⁄2 11⁄2 1⁄2 41⁄4 2 28-78
28-64 1⁄2 2 1⁄2 41⁄4 2 28-78
SW HW CW LW
Page 64
28-75 Bearings Kits For Bearing Tools
KIT NO. BEARING SIZE DESCRIPTION
28-79 3⁄8”O.D. x 3⁄16”I.D. Bearing, Washer & Screw
28-86 21⁄2”O.D 2 Bearings w/Hardware
■ Bearing kits which include bearing, washer and locknut or screw as required.
KIT NO. BEARING SIZE DESCRIPTION
28-78 1⁄2”O.D. x 3⁄16”I.D. Bearing, Washer & Screw
28-80 1⁄4”O.D. x 1⁄8”I.D. Bearing & Screw
PART# KIT# PART# KIT# PART# KIT# PART# KIT# PART# KIT# PART# KIT#28-50 28-7928-51 28-7928-52 28-7828-53 28-7828-54 28-78
28-55 28-8028-56 28-7828-57 28-7828-59 28-7828-63 28-78
28-64 28-7829-51 28-7829-52 28-7829-53 28-7842-01 28-78
42-02 28-7842-03 28-7842-04 28-7842-05 28-7842-06 28-78
42-07 28-7842-08 28-7842-09 28-7842-10 28-7842-11 28-78
42-12 28-7842-13 28-7843-52 28-78
Each Onsrud Cutter bearing tool is listed with applicable replacement bearing kit.
29-50 Double Edge - Carbide TippedChamfer
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART# BEVEL CEL SHK DIA OAL BEARINGKIT
29-53 25° 3⁄8 1⁄4 17⁄8 28-78
Provides a beveled or decorative edgeon finished parts.
PART# BEVEL CEL SHK DIA OAL BEARINGKIT
29-51 45° 1⁄2 1⁄4 2 28-78
29-52 45° 1⁄2 1⁄2 21⁄2 28-78
SW HW CW
Right Hand
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
36-00 Double Edge - Carbide TippedDovetail
PART# LG SM CEL ANGLE SHK OALDIA DIA PER SIDE DIA
36-07 1⁄2 1⁄4 1⁄2 14°2’ 1⁄2 21⁄8
36-12 3⁄4 1⁄2 3⁄4 9°28’ 1⁄2 21⁄4
HELIX ANGLE ≈ 5° - 10° Shear
The best mechanical all wood methodof joining two right angle members, adovetail joint.
PART# LG SM CEL ANGLE SHK OALDIA DIA PER SIDE DIA
36-03 3⁄8 3⁄163⁄8 14°2’ 1⁄4 13⁄4
36-05 3⁄8 1⁄4 3⁄8 9°28’ 1⁄2 17⁄8
SW HW CW MTDT
Page 65Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
CARBIDE TIPPEDSOLID CARBIDE
■ Usage Plastic and solid surface, composites,laminated and veneer
■ MaterialSee SelectionGuide - pg. 2 - 12
37-50 Double Edge - V Bottom37-60
PART # CED CEL SHK DIA OAL
37-61 1⁄2 13⁄32 1⁄4 125⁄32
37-62 3⁄4 1⁄2 1⁄2 21⁄8
37-63 1 27⁄32 1⁄2 227⁄32
Designed for V grooving or beveling90°.
PART # CED CEL SHK DIA OAL
37-50 3⁄16 5⁄8 1⁄4 2
37-51 1⁄4 3⁄4 1⁄4 2
37-52 3⁄8 3⁄4 3⁄8 21⁄2
HELIX ANGLE ≈ 3° - 5° Shear
SW HW CW LWSP HP SSP
■ Usage Wood, plastic, aluminum andsolid surface
■ Material See SelectionGuide - pg. 2 - 12
37-00 Single Edge - Solid Carbide37-20 Engraving Tools
PART # TIP ANGLE SHK DIA OAL
37-21 0.005 30 1⁄4 2
37-23 0.010 30 1⁄4 2
37-25 0.020 30 1⁄4 2
37-27 0.030 30 1⁄4 2
37-29 0.040 30 1⁄4 2
37-31 0.060 30 1⁄4 2
37-35 0.090 30 1⁄4 2
37-39 30 Degree Kit
The half round engraving tools are offeredwith a wide range of tip sizes and anglesto accommodate many engraving styles.
PART # TIP ANGLE SHK DIA OAL
37-01 0.005 60 1⁄4 2
37-03 0.010 60 1⁄4 2
37-05 0.020 60 1⁄4 2
37-07 0.030 60 1⁄4 2
37-09 0.040 60 1⁄4 2
37-11 0.060 60 1⁄4 2
37-15 0.090 60 1⁄4 2
37-19 60 Degree Kit
SW HW SP HP SSP
■ Usage Aluminum/plastic sandwich materials
■ Material See Selection Guide - pg. 2 - 12
37-70 Double Edge - Carbide TippedFolding Tool for Dibond/Alucobond
PART # CED CEL SHK DIA OAL
37-72 1⁄2 3⁄8 1⁄2 2
Designed for cutting aluminum/plasticsandwich materials with 90° angle andflat bottom.
PART # CED CEL SHK DIA OAL
37-71 1⁄2 3⁄8 1⁄4 2
90° angle and .090 flat for folding material
A
A
Page 66
CARBIDE TIPPEDSOLID CARBIDE
■ Usage Natural wood, wood composites, laminatedand veneered, plastic and solid surface
■ Material See SelectionGuide - pg. 2 - 12
38-50 Double Edge - Round Bottom 38-60
PART # CED CEL SHK DIA OAL
38-53 3⁄8 3⁄4 3⁄8 21⁄4
38-61 1⁄2 11⁄321⁄4 2
Round bottom tools featuring upshearaction for grooving and decorativeface cutting.
PART # CED CEL SHK DIA OAL
38-50 1⁄8 3⁄8 1⁄4 2
38-51 3⁄165⁄8 1⁄4 2
38-52 1⁄4 3⁄4 1⁄4 2
HELIX ANGLE ≈ 2° - 4° Shear
SW HW CW LWSP HP SSP
■ Usage Natural wood, wood composites,plastic and solid surface
■ Material See SelectionGuide - pg. 2 - 12
40-50 Double Edge - Carbide Tipped Round & Rout
PART# CED SM CEL SHK OAL CE CED DIA RAD
40-53 11⁄8 1⁄2 1.437 1⁄2 311⁄161⁄4
40-54 13⁄8 1⁄2 .938 1⁄2 33⁄163⁄8
40-55 13⁄8 1⁄2 1.437 1⁄2 311⁄163⁄8
Designed to put a radius on the edgeand dress the stock. They will providea smooth finish.
PART# CED SM CEL SHK OAL CE CED DIA RAD
40-50 1 1⁄2 .938 1⁄2 33⁄163⁄16
40-51 1 1⁄2 1.437 1⁄2 311⁄163⁄16
40-52 11⁄8 1⁄2 .937 1⁄2 33⁄161⁄4
SW HW CW SP HP SSP
PART # CED CEL SHK DIA OAL ANGLE
37-92 2 0.577 1⁄2 27⁄8 120º
37-97 2 0.363 1⁄2 25⁄8 140º
37-80 Double Edge - Carbide TippedNEW Lettering Bits
Designed for V grooving or bevelingedges of parts. The tools are designedto cut a wide variety of wood productsand produce a clean edge.
■ Usage Wood
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL ANGLE
37-82 1 0.856 1⁄2 31⁄2 60º
37-87 11⁄2 0.750 1⁄2 3 90º
SW CWHW
Page 67Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Natural wood, wood compositesand solid surface
■ Material See Selection Guide - pg. 2 - 12
42-00 Double Edge - Carbide Tipped Corner Round
PART# RADIUS CED CEL SHK OAL BEARINGDIA KIT
42-04 5⁄16 11⁄8 9⁄161⁄4 21⁄4 28-78
42-05 3⁄8 11⁄4 5⁄8 1⁄4 21⁄32 28-78
42-13 3⁄8 11⁄4 11⁄161⁄2 25⁄8 28-78
42-06 1⁄2 11⁄2 3⁄4 1⁄4 25⁄32 28-78
42-07 1⁄2 11⁄2 3⁄4 1⁄2 211⁄16 28-78
42-08 3⁄4 2 11⁄321⁄2 3 28-78
Quarter round profile tools feature upshear geometry for better finishes.
PART# RADIUS CED CEL SHK OAL BEARINGDIA KIT
42-09 1⁄1611⁄16
5⁄161⁄4 115⁄16 28-78
42-11 1⁄8 3⁄4 5⁄161⁄2 23⁄16 28-78
42-10 1⁄8 3⁄4 3⁄8 1⁄4 21⁄8 28-78
42-03 5⁄3213⁄16
15⁄321⁄4 23⁄32 28-78
42-01 3⁄167⁄8 1⁄2 1⁄4 2 28-78
42-02 1⁄4 1 7⁄161⁄4 129⁄32 28-78
42-12 1⁄4 1 9⁄161⁄2 25⁄8 28-78
SW HW CW SSP
47-00 Double Edge - Carbide TippedNEW MDF Panel Tools
These cutters can create 12 cabinetcombinations by combining differentstile and panel cutters to get thedesired shape in MDF material.
■ Usage MDF
■ Material See Selection Guide - pg. 2 - 12
PART # CED SHANK OAL DESCRIPTION
47-02 7⁄8 1⁄2 21⁄2 Bead Profile - Stile Bits
47-04 11⁄4 1⁄2 21⁄2 Traditional Profile - Stile Bits
47-06 11⁄4 1⁄2 21⁄2 Ogee Profile - Stile Bits
47-08 11⁄4 1⁄2 21⁄2 Straight Profile - Stile Bits
47-10 11⁄2 1⁄2 21⁄2 Cove Profile - Panel Bits
47-12 11⁄2 1⁄2 21⁄2 Straight Profile - Panel Bits
47-14 11⁄2 1⁄2 21⁄2 Ogee Profile - Panel Bits
CW
STILE BITS
PANEL BITS
TOOL COMBINATIONS47-02 & 47-1247-02 & 47-10 47-02 & 47-14
47-04 & 47-1247-04 & 47-10 47-04 & 47-14
47-06 & 47-1247-06 & 47-10 47-06 & 47-14
47-08 & 47-1247-08 & 47-10 47-08 & 47-14
Page 68
HIGH SPEED STEEL SOLID CARBIDE
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
90-00 T Slot
PART # CED CEL NECK SHK DIA OAL FLUTES
90-06 3⁄8 3⁄8 3⁄16 1⁄4 15⁄8 2
Designed to bore a hole and rout a Tshape slot for plaques and frames toprovide for built in wall mountingcapabilities.
PART # CED CEL NECK SHK DIA OAL FLUTES
90-02 3⁄8 5⁄16 3⁄16 1⁄2 2 2
SW HW CW
■ Usage Natural wood
■ Material See Selection Guide - pg. 2 - 12
24-300 Four Edge - High Speed Steel Straight Mortising
PART # CED CEL SHK DIA OAL
24-350 1⁄2 2 13 mm 41⁄2
24-370 5⁄8 2 13 mm 41⁄2
Designed with updated geometry for European oscillating mortisingmachines. Tools can be used in aright or left hand rotation.
PART # CED CEL SHK DIA OAL
24-310 1⁄4 13⁄4 13 mm 41⁄2
24-330 3⁄8 13⁄4 13 mm 41⁄2
SW HW MTDT
PART # CED CEL SHK DIA OAL
29-012 5⁄8 27⁄8 5⁄8 5
29-015 3⁄4 27⁄8 3⁄4 5
29-000 HSS Hollow Core CuttersNEW
This specialized cutter is designedto vertically cut the honeycomb cellsproducing a clean, flag free edge.The core material will remainattached at the bottom and can beremoved using one of our valve stylehoneycomb cutters. This product alongwith our 31-100 or 30-000 series toolsis an effective combination to createpockets in honeycomb core and geta perfectly clean edge.
PART # CED CEL SHK DIA OAL
29-003 1⁄4 11⁄2 1⁄4 33⁄4
29-006 3⁄8 17⁄8 3⁄8 33⁄4
29-009 1⁄2 27⁄8 1⁄2 5
■ Usage Honeycomb
■ Material See Selection Guide - pg. 2 - 12CP
Page 69Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
These tools are for contouring, carving and chamferingcuts of .25" or less. The unique patented holding systemprevents the solid carbide blades from coming out of theholder if it is fractured.
The HSS saw blades and the diamond plated blades dish on the bottom so they clear the cut core finish like the hollowground solid carbide style rings. The solid carbide rings may be reground several times at the factory making them veryeconomical to use.
The HSS saw and diamond plated blades are disposable, offering the convenience of a constant diameter.
30-300 PM-HSS Integral ShankHoneycomb Hogger CutterSuper PM High Speed Steel Hoggers • High Speed Replaceable Saw Blade Solid Carbide Replaceable Blade • Diamond Plated Replaceable Blade
Shan
k D
iam
eter
Cutting Diameter
Diameter
Hog
ger
Dep
th
OAL
PART # CUTTING HOGGER SHANK OAL DIA SOLID SOLID CARBIDE DIAMOND HSS SAW REPLACEMENTDIAMETER DEPTH DIAMETER CARBIDE W/TEETH PLATED SCREW
30-310 7⁄8 11⁄2 1⁄2 31⁄2 1" 30-012 30-313 30-113 30-213 30-011-2
30-315 11⁄4 11⁄2 1⁄2 31⁄2 1.5" 30-014 30-314 30-114 30-214 30-020-4
30-321 13⁄4 11⁄2 1⁄2 31⁄2 2" 30-022 30-322 30-122 30-222 30-020-4
30-331 23⁄4 1 1⁄2 31⁄2 3" 30-032 30-332 30-132 30-232 30-030-4
30-341 33⁄4 1 3⁄4 31⁄2 4" 30-042 30-342 30-142 30-242 30-040-4
FEEDS & SPEEDS30-000/30-300
PM-HSS HOGGER CUTTERS (body only)
CUTTING BLADE OPTIONS
CUTTING BLADE OPTIONS
FEEDRATES
SPINDLESPEED
30-000 Replaceable Ring Type Honeycomb Cutter
SHANK BLADE SOLID SOLID CARBIDE DIAMOND HSS SAW REPLACEMENTASSEMBLY DIAMETER CARBIDE W/TEETH PLATED SCREW
30-011 1” 30-012 30-313 30-112 30-213 30-011-2
30-021 2” 30-022 30-322 30-122 30-222 30-020-4
30-031 3” 30-032 30-332 30-132 30-232 30-030-4
30-041 4” 30-042 30-342 30-142 30-242 30-040-4
CORE TYPE SOLID SOLID CARBIDE DIAMOND HSSCARBIDE W/TEETH SAW
Aluminum, Less than 5#/cuft 100 100 NR 150
Aluminum, More than 5#/cuft 100 100 NR 100
Paper based 400 400 NR 250
Paper, based with Fiber Reinforcement 800 800 400 150
Fiberglass 600 600 600 NR
Phenolic 200 200 400 NR
Polycarbonate NR NR 800 NR
Aramid, Less than 5#/cuft 800 800 400 150
Aramid, More than 5#/cuft 800 800 400 NR
Feedrate = Inches Per Minute (IPM)
NOTE: 30-300 assembly requires one (1) hogger and one (1) blade
MAXDIA RPM
1 25000
11⁄2 25000
2 18000
3 15000
4 12000
■ Usage For contouring, carving and chamfering cuts
■ Material See Selection Guide - pg. 2 - 12CP
The spiral hogger geometry ground integralto the shank allows for faster feed rates anddeeper cuts than any previous cutter. Theavailability of several different blades makesthis cutter suitable for most core types. Thenew hogger design also imparts less forceas it evacuates and shreds scrap.
■ Usage CNC machining of honeycomb core
■ Material See Selection Guide - pg. 2 - 12CP
Solid Carbide
Diamond Plated
HSSSaw
Page 70
CORE TYPE RATING
Aluminum, Lo Density (Less than 5#/cuft) 1
Aluminum, Hi Density (More than 5#/cuft) 2
Paper 2
Paper, Reinforced N
Fiberglass N
Phenolic N
Polycarbonate N
Aramid N
1 - Excellent, 2 - Good, N - Not Recommended
31-000 High Speed Steel Cutter
PART # CED SHK DIA OAL
31-010 1⁄2 1⁄4 21⁄16
31-015 3⁄4 1⁄4 23⁄32
31-020 1 1⁄4 21⁄831-025 11⁄2 1⁄2 21⁄431-030 2 1⁄2 2 3⁄431-040 3 1⁄2 215⁄16
■ Usage Aluminum Core
■ Material See Selection Guide - pg. 2 - 12
This cutter is designed primarily for use on aluminum core, offering theversatility of smaller sizes for use on hand-held machines in field ormaintenance type repairs. This cutter offers the strength of an integralshank and blade that has an edge sharpness unattainable with any othermaterial. This sharpness and the relieved bottom yield part surfaces thatrequire a minimum of preparation before bonding operation.
CP
PART # CED SHK DIA OAL
31-106TCN 5⁄8 1⁄4 3
31-108TCN 3⁄4 1⁄4 3
31-100 High Speed SteelNEW Honeycomb Cutter With Teeth
The small diameter honeycombcutters were designed to offer theflexibility of cutting small slots orpockets in honeycomb core. The toolsare versatile and can be used on CNCmachines or hand held machines forfield or maintenance type repairs.
■ Usage For contouring, carving, pocketing, andchamfer cuts
■ Material See Selection Guide - pg. 2 - 12
PART # CED SHK DIA OAL
31-102TCN 3⁄8 1⁄4 3
31-104TCN 1⁄2 1⁄4 3
CP
Page 71Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
MAXDIA RPM3⁄8 350001⁄2 350003⁄4 35000
1 30000
11⁄2 25000
13⁄4 25000
2 20000
21⁄2 20000
3 20000
Solid Carbide
Diamond Plated
FEEDS AND SPEEDSAvailable Cutting Blades for 31-000 and 32-000 Series.
Hogger
Shank
1/2”
32-000 PM High Speed Steel Hogger
PART # HOGGER HOGGER SHANK BLADE SOLID DIAMOND HSS HSS SAW ADAPTER FORDIAMETER DEPTH PART # DIAMETER CARBIDE PLATED WAVY RING HSS SAW
32-022 (44mm) (16mm) 32-021 (45mm) 1.77” 32-026 - 32-023 - -
1.73 ” 0.63 “ (50mm) 1.97” - 32-029* - 32-027* 32-028
32-032 (61.5mm) (16mm) 32-031 (63mm) 2.48” 32-036 - 32-033 - -
2.42 “ 0.63 “ (75mm) 2.95” - 32-039* - 32-037* 32-038
PM-HSS HOGGER CUTTING BLADE OPTIONSSHK
(All Shanks are 1/2” Diameter) 32-100 Wrench for 32-000 Series Tools * Requires adapter for saws
HSS Saw
PM-HSSWavy Ring
FEEDRATES
SPINDLESPEED
CORE TYPE SOLID DIAMOND HSS HSS HSS HSSCARBIDE PLATED SAW WAVY (31-000) (31-100)
Aluminum, Less than 5#/cuft 100 NR 150 100 100-140 90-140
Aluminum, More than 5#/cuft 100 NR 100 100 70 70
Paper based 300 NR 200 300 50 50
Paper, based w/Fiber Reinforcement 400 300 600 300 100-150 100-150
Fiberglass NR 600 NR NR NR NR
Phenolic NR 600 NR NR NR NR
Polycarbonate NR 800 NR NR NR NR
Aramid, Less than 5#/cuft 200 NR 150 200 100-150 100-150
Aramid, More than 5#/cuft 200 400 NR NR NR NR
Feedrate = Inches Per Minute (IPM)
■ Usage Fast removal of excess core
■ Material See Selection Guide - pg. 2 - 12
These cutters are specifically designed for fast (lowforce) removal of excess core followed by a finalfinish pass to obtain excellent finishes with one tool.These cutters enable cuts of up to .60” depths in asingle pass. The availability of several differentblades makes this cutter suitable for most core types.
All assemblies require a shank, hogger and blade.
CP
Page 72
34-000 Aircraft Panel ToolsNEW
This modular tool is designed to produce slots in compositepanels so potting compound can be applied to strengthenthe edge. This tool consists of a PCD arbor which accepts adiamond grit or HSS under cutting tool to be screwed into it.
■ Usage Composites
■ Material See Selection Guide - pg. 2 - 12CP
PART # CED CEL SHK DIA
34-010 1⁄2 1⁄4 1⁄2 PCD Arbor
34-022 7⁄8 0.130 n/a Diamond Grit Cutter
34-024 7⁄8 0.250 n/a Diamond Grit Cutter
34-026 7⁄8 0.380 n/a Diamond Grit Cutter
34-028 7⁄8 0.500 n/a Diamond Grit Cutter
34-030 7⁄8 0.630 n/a Diamond Grit Cutter
34-042 7⁄8 0.130 n/a HSS Saw
34-044 7⁄8 0.250 n/a HSS Saw
34-046 7⁄8 0.380 n/a HSS Saw
34-048 7⁄8 0.500 n/a HSS Saw
34-050 7⁄8 0.630 n/a HSS Saw
CORE TYPE CUTTER RPM FEEDRATE CUT DIRECTION
Fiberglass panels with paper core (Nomex) Diamond Grit 18,000 220 lpm Conventional
Aluminum panels with aluminum core HSS Saw 16,000 120 lpm Conventional
■ Usage Natural wood, sheet and stacked aluminum
■ Material See Selection Guide - pg. 2 - 12
40-000 Single Edge - High SpeedSteel Upcut Spiral
PART # CED CEL SHK DIA OAL
40-021 5⁄16 3⁄4 1⁄2 31⁄4
40-023 5⁄16 1 1⁄2 31⁄2
40-025 21⁄64 3⁄4 1⁄2 31⁄4
40-031 3⁄8 1 3⁄8 3
40-033 3⁄8 1 1⁄2 31⁄2
40-035 3⁄8 11⁄4 1⁄2 33⁄4
40-037 1⁄2 11⁄4 1⁄2 31⁄4
40-039 1⁄2 11⁄2 1⁄2 31⁄2
40-041 1⁄2 11⁄2 1⁄2 41⁄2
Designed for routing applicationswhere speed and chip removal areprimary considerations. They arealso recommended when grooving,slotting or blind routing.
PART # CED CEL SHK DIA OAL
40-001 1⁄8 3⁄8 1⁄4 25⁄8
40-003 3⁄16 5⁄8 1⁄4 27⁄8
40-053 7⁄32 7⁄8 1⁄4 3
40-005 1⁄4 5⁄8 1⁄4 23⁄4
40-007 1⁄4 3⁄4 1⁄4 23⁄4
40-009 1⁄4 3⁄4 1⁄2 31⁄4
40-011* 1⁄4 1 1⁄4 3
40-015 5⁄16 1 5⁄16 3
40-019 5⁄16 1 3⁄8 3
HELIX ANGLE ≈19° - 32° Shear
* These tools are designed and toleranced for air routers with guide bushings.
SW HW A
Page 73Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Natural wood and sheet aluminum
■ Material See Selection Guide - pg. 2 - 12
40-000 Single Edge - High SpeedSteel Downcut Spiral
PART # CED CEL SHK DIA OAL
40-024 5⁄16 1 1⁄2 31⁄2
40-028 21⁄64 1 1⁄2 31⁄2
40-032* 3⁄8 1 3⁄8 3
40-034 3⁄8 1 1⁄2 31⁄2
40-036 3⁄8 11⁄4 1⁄2 33⁄4
40-040 1⁄2 11⁄2 1⁄2 31⁄2
Designed for through cut routingoperations where speed is the primaryconcern and fixturing is such thatboth chips and material are betteroff forced down.
PART # CED CEL SHK DIA OAL
40-002 1⁄8 3⁄8 1⁄4 25⁄8
40-004 3⁄16 5⁄8 1⁄4 27⁄8
40-008 1⁄4 3⁄4 1⁄4 23⁄4
40-010 1⁄4 3⁄4 1⁄2 31⁄4
40-012 1⁄4 1 1⁄4 3
40-022 5⁄16 3⁄4 1⁄2 31⁄4
HELIX ANGLE ≈ 19° - 32° Shear
* These tools are designed and toleranced for air routers with guide bushings.
SW HW A
■ Usage Natural wood sheet, block & plate aluminum
■ Material See Selection Guide - pg. 2 - 12
40-100 Double Edge - High SpeedSteel Upcut Spiral
PART # CED CEL SHK DIA OAL
40-115 5⁄16 1 5⁄16 3
40-123 5⁄16 1 1⁄2 31⁄2
40-131* 3⁄8 1 3⁄8 3
40-133 3⁄8 1 1⁄2 31⁄2
40-135 3⁄8 11⁄4 1⁄2 33⁄4
40-143 1⁄2 1 1⁄2 3
40-137 1⁄2 11⁄4 1⁄2 31⁄4
40-139 1⁄2 11⁄2 1⁄2 31⁄2
40-141 3⁄4 11⁄4 1⁄2 31⁄4
Provides a smoother finish whengrooving, slotting or blind routing thando single edge tools. Recommendedwhen fixturing requires upward chipremoval.
PART # CED CEL SHK DIA OAL
40-101 1⁄8 3⁄8 1⁄4 25⁄8
40-103 3⁄16 5⁄8 1⁄4 27⁄8
40-153 7⁄32 7⁄8 1⁄4 3
40-105 1⁄4 5⁄8 1⁄4 23⁄4
40-107 1⁄4 3⁄4 1⁄4 23⁄4
40-109 1⁄4 3⁄4 1⁄2 31⁄4
40-111* 1⁄4 1 1⁄4 3
40-121 5⁄16 3⁄4 1⁄2 31⁄4
40-117 5⁄16 3⁄4 3⁄8 3
HELIX ANGLE ≈ 19° - 32° Shear
* These tools are designed and toleranced for air routers with guide bushings.
SW HW A
Page 74
■ Usage Natural wood, sheet & aluminum extrusions
■ Material See Selection Guide - pg. 2 - 12
40-100 Double Edge - High SpeedSteel Downcut Spiral
PART # CED CEL SHK DIA OAL
40-116 5⁄16 1 5⁄16 3
40-124 5⁄16 1 1⁄2 31⁄2
40-132* 3⁄8 1 3⁄8 3
40-134 3⁄8 1 1⁄2 31⁄2
40-136 3⁄8 11⁄4 1⁄2 33⁄4
40-138 1⁄2 11⁄4 1⁄2 31⁄4
40-140 1⁄2 11⁄2 1⁄2 31⁄2
40-142 3⁄4 11⁄4 1⁄2 31⁄4
Provides a smoother finish than singleedge in trimming and sizing.Recommended when chip flow shouldbe directed down to protect the finishon the top of the material being cut.
PART # CED CEL SHK DIA OAL
40-102 1⁄8 5⁄16 1⁄4 25⁄8
40-104 3⁄165⁄8 1⁄4 27⁄8
40-106 1⁄4 5⁄8 1⁄4 23⁄4
40-108 1⁄4 3⁄4 1⁄4 23⁄4
40-110 1⁄4 3⁄4 1⁄2 31⁄4
40-112* 1⁄4 1 1⁄4 3
40-158* 1⁄4 1 1⁄4 31⁄4
40-122 5⁄163⁄4 1⁄2 31⁄4
HELIX ANGLE ≈ 19° - 32° Shear
* These tools are designed and toleranced for air routers with guide bushings.
SW HW A
■ Usage Foam Boards
■ Material See Selection Guide - pg. 2 - 12
40-550 Four Edge - High Speed SteelUpcut Spiral Foam Cutters
PART # CED CEL SHK DIA OAL
40-564 1⁄2 41⁄8 1⁄2 61⁄2
HELIX ANGLE ≈ 25°
Designed to cut thick foam withupward chipflow.
PART # CED CEL SHK DIA OAL
40-562 1⁄2 35⁄8 1⁄2 6
HELIX ANGLE ≈ 25°
FP
■ Usage Natural wood, wood composites,composite plastic and foam
■ Material See Selection Guide - pg. 2 - 12
48-000 Single Edge - Carbide TippedStraight
PART # CED CEL SHK DIA OAL
48-056 3⁄8 11⁄4 1⁄2 23⁄4
48-065 1⁄2 11⁄4 1⁄2 23⁄4
48-069 1⁄2 11⁄2 1⁄2 3
48-070 1⁄2 2 1⁄2 4
48-075 1⁄2 2 1⁄2 5
Designed for general usage wherefaster feed rates, free cutting actionand long tool life are essential.
PART # CED CEL SHK DIA OAL
48-005 1⁄4 7⁄8 1⁄4 23⁄8
48-007 1⁄4 1 1⁄4 23⁄8
48-079* 1⁄4 1 1⁄4 31⁄4
48-031 1⁄4 1 1⁄2 21⁄2
48-155* 3⁄8 11⁄4 3⁄8 3
HW CW CP FP
Page 75Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
48-500 Double Edge - Carbide TippedStraight Left Hand
PART # CED CEL SHK DIA OAL
48-576 1⁄2 11⁄4 1⁄2 23⁄4
48-580 1⁄2 11⁄2 1⁄2 3
Carbide tipped tools in popular sizeswhere left hand rotation is required.
PART # CED CEL SHK DIA OAL
48-506 1⁄4 7⁄8 1⁄4 23⁄8
48-557 3⁄8 1 1⁄2 21⁄2
HW CW
■ Usage Natural wood, wood composites,composite plastic and foam
■ Material See Selection Guide - pg. 2 - 12
48-000 Double Edge - Carbide TippedStraight
PART # CED CEL SHK DIA OAL
48-183 1⁄2 21⁄2 1⁄2 41⁄2
48-083 17⁄32 11⁄4 1⁄2 23⁄4
48-182 9⁄16 1 1⁄4 21⁄4
48-082 9⁄16 11⁄4 1⁄2 23⁄4
48-015 5⁄8 1 1⁄4 21⁄4
48-086 5⁄8 11⁄4 1⁄2 23⁄4
48-187 11⁄16 1 1⁄4 23⁄8
48-087 11⁄16 11⁄4 1⁄2 23⁄4
48-016 3⁄4 1 1⁄4 21⁄4
48-088 3⁄4 11⁄4 1⁄2 3
48-089 3⁄4 11⁄2 1⁄2 3
48-215 3⁄4 2 3⁄4 4
48-189 25⁄32 11⁄4 1⁄2 23⁄4
48-090 13⁄16 11⁄4 1⁄2 23⁄4
48-096 7⁄8 11⁄4 1⁄2 23⁄4
48-115 15⁄16 11⁄4 1⁄2 23⁄4
48-100 1 11⁄4 1⁄2 23⁄4
48-250 1 2 3⁄4 4
48-120 11⁄8 11⁄4 1⁄2 23⁄4
48-150 11⁄4 11⁄4 1⁄2 23⁄4
48-156 13⁄8 11⁄4 1⁄2 23⁄4
48-160 11⁄2 11⁄4 1⁄2 23⁄4
48-170 15⁄8 11⁄4 1⁄2 23⁄4
48-200 2 11⁄4 1⁄2 23⁄4
*These tools are designed and toleranced for Air Routers with guide bushings.
Designed for general usage wheresuperior balance and vibration freecutting provides a smoother finishalong with long tool life.
PART # CED CEL SHK DIA OAL
48-008+ 1⁄8 5⁄16 1⁄4 2
48-000 3⁄16 1⁄2 1⁄4 2
48-004 1⁄4 5⁄8 1⁄4 21⁄8
48-006 1⁄4 7⁄8 1⁄4 23⁄8
48-018 1⁄4 7⁄8 1⁄2 21⁄2
48-106 1⁄4 1 1⁄4 23⁄8
48-179* 1⁄4 1 1⁄4 31⁄4
48-017 5⁄163⁄4 1⁄2 21⁄4
48-010 5⁄16 1 1⁄4 21⁄2
48-122 5⁄16 1 5⁄16 21⁄2
48-012 3⁄8 3⁄4 1⁄4 21⁄4
48-154 3⁄8 3⁄4 1⁄2 21⁄4
48-013 3⁄8 1 1⁄4 23⁄8
48-036* 3⁄8 1 3⁄8 21⁄2
48-057 3⁄8 1 1⁄2 21⁄2
48-058* 3⁄8 11⁄4 3⁄8 3
48-158 3⁄8 11⁄4 1⁄2 23⁄4
48-014 1⁄2 3⁄4 1⁄4 21⁄8
48-072 1⁄2 1 1⁄2 21⁄2
48-044 1⁄2 11⁄4 3⁄8 23⁄4
48-076 1⁄2 11⁄4 1⁄2 23⁄4
48-080 1⁄2 11⁄2 1⁄2 3
48-081 1⁄2 2 1⁄2 4
48-181 1⁄2 21⁄4 1⁄2 41⁄4
+ Solid Carbide
HW CW CP FP
Page 76
Single Edge
Double Edge
SINGLE EDGE DOUBLE EDGE
■ Usage Plastic and composite plastic
■ Material See Selection Guide - pg. 2 - 12
48-600 Single & Double Edge - CarbideTipped Straight
PART # CED CEL SHK DIA OAL
48-652 1⁄4 3⁄4 1⁄4 21⁄8
48-679* 1⁄4 3⁄4 1⁄4 31⁄4
48-656 3⁄8 1 3⁄8 21⁄2
48-658 1⁄2 11⁄4 1⁄2 23⁄4
Designed specifically for cuttingharder, more rigid plastics. Singleedge for faster feed rates. Doubleedge for smoother finish.
PART # CED CEL SHK DIA OAL
48-603 1⁄4 3⁄4 1⁄4 21⁄8
48-607 3⁄8 1 3⁄8 21⁄2
48-635* 3⁄8 1 3⁄8 31⁄2
* These tools are designed and toleranced for air routers with guide bushings.
HP CP
■ Usage Wood composites
■ Material See Selection Guide - pg. 2 - 12
48-700 Double Edge - Carbide TippedCNC & MDF
PART # CED CEL SHK DIA OAL
48-710 3⁄4 15⁄8 3⁄4 4
48-703 3⁄4 21⁄8 3⁄4 4
48-704 3⁄4 25⁄8 3⁄4 41⁄2
48-711 3⁄4 3 3⁄4 53⁄8
48-712 1 21⁄8 3⁄4 41⁄4
48-713 1 3 3⁄4 51⁄8
Designed with special carbide,stiffer tool bodies and superior edgegeometry to withstand the rigor ofCNC routing of MDF materials.
PART # CED CEL SHK DIA OAL
48-700 1⁄4 7⁄8 1⁄4 31⁄4
48-706 3⁄8 1 1⁄2 33⁄8
48-707 1⁄2 1 1⁄2 31⁄4
48-714 1⁄2 11⁄4 1⁄2 23⁄4
48-702 1⁄2 11⁄4 1⁄2 31⁄2
48-708 1⁄2 2 1⁄2 43⁄8
48-709 5⁄8 2 5⁄8 41⁄4
CW
■ Usage Aluminum and non-abrasive plastics
■ Material See Selection Guide - pg. 2 - 12
49-000 Double Edge - High Speed SteelDowncut
PART # CED CEL SHK DIA OAL
49-002 5⁄16 3⁄4 5⁄16 21⁄2
49-003 3⁄8 3⁄4 3⁄8 21⁄2
These double edge downcuts with adrill type point were developed initiallyas “Aircraft Throwaway” tools. Theyhave many uses in trimming and routingprimarily with hand held routers.
PART # CED CEL SHK DIA OAL
49-005 1⁄4 9⁄16 1⁄4 21⁄2
49-001 1⁄4 9⁄16 1⁄4 23⁄4
49-007 1⁄4 9⁄16 1⁄4 31⁄4
THESE TOOLS ARE DESIGNED AND TOLERANCEDFOR AIR ROUTERS WITH GUIDE BUSHINGS, + .000 - .006
HELIX ANGLE ≈ 24°
A
Page 77Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Fiberglass, phenolic, acetal, solid surfaceand aluminum slab
■ Material See Selection Guide - pg. 2 - 12
52-000 Double Edge - Solid CarbideUpcut Spiral
PART # CED CEL SHK DIA OAL
52-100 5⁄16 13⁄163⁄8 21⁄2
52-120 3⁄8 7⁄8 3⁄8 21⁄2
52-140 7⁄16 1 1⁄2 3
52-160 1⁄2 1 1⁄2 3
Designed as a general purpose spiralwith several times the life of their highspeed steel counterparts. They areused when upward chip flow is preferred.
PART # CED CEL SHK DIA OAL
52-040 1⁄8 1⁄2 1⁄4 2
52-050 5⁄32 9⁄16 1⁄4 2
52-060 3⁄165⁄8 1⁄4 2
52-080 1⁄4 3⁄4 1⁄4 21⁄2
52-090 9⁄323⁄4 3⁄8 21⁄2
HELIX ANGLE ≈ 30°
CP SSPA
■ Usage Natural wood, wood compositessolid surface, and some plastic
■ Material See Selection Guide - pg. 2 - 12
52-200 Double Edge - Solid CarbideUpcut Spiral Wood Rout
PART # CED CEL SHK DIA OAL
52-320 3⁄8 11⁄8 3⁄8 3
52-325 3⁄8 11⁄4 3⁄8 3
52-325L 3⁄8 11⁄4 3⁄8 3
52-330 3⁄8 11⁄4 1⁄2 3
52-340 7⁄16 1 1⁄2 3
52-360 1⁄2 11⁄8 1⁄2 3
52-361(S) 1⁄2 11⁄8 1⁄2 3
52-362 1⁄2 11⁄4 1⁄2 31⁄2
52-365 1⁄2 15⁄8 1⁄2 31⁄2
52-365L 1⁄2 15⁄8 1⁄2 31⁄2
52-366(S) 1⁄2 15⁄8 1⁄2 31⁄2
52-367 1⁄2 21⁄8 1⁄2 4
52-370 17⁄32 11⁄8 1⁄2 3
52-380 5⁄8 15⁄8 5⁄8 31⁄2
52-385 5⁄8 21⁄8 5⁄8 4
52-385L 5⁄8 21⁄8 5⁄8 4
52-390 3⁄4 15⁄8 3⁄4 4
52-395 3⁄4 21⁄8 3⁄4 4
52-395L 3⁄4 21⁄8 3⁄4 4
Designed for routing where upwardchip removal, tool rigidity, long life andhigh quality finish is desired.
PART # CED CEL SHK DIA OAL
52-244 1⁄8 1⁄2 1⁄8 2
52-240 1⁄8 1⁄2 1⁄4 2
52-240L 1⁄8 1⁄2 1⁄4 2
52-250 5⁄325⁄8 1⁄4 2
52-260 3⁄163⁄4 1⁄4 2
52-260L 3⁄163⁄4 1⁄4 2
52-261 3⁄163⁄4 1⁄4 21⁄2
52-270 7⁄323⁄4 1⁄4 21⁄2
52-271 7⁄32 1 1⁄4 21⁄2
52-280 1⁄4 7⁄8 1⁄4 21⁄2
52-281(S) 1⁄4 7⁄8 1⁄4 21⁄2
52-285 1⁄4 1 1⁄4 21⁄2
52-285L 1⁄4 1 1⁄4 21⁄2
52-287 1⁄4 11⁄8 1⁄4 3
52-290 9⁄32 1 5⁄16 21⁄2
52-300 5⁄16 11⁄8 5⁄16 3
52-310 5⁄16 11⁄8 1⁄2 3
52-310L 5⁄16 11⁄8 1⁄2 3
52-318* 3⁄8 1 3⁄8 3
HELIX ANGLE ≈ 30° L = Left Hand Rotation
* Special Point(S) = Soft Wood Geometry
SW HW CW SP SSP
Page 78
■ Usage Plastic, solid surface, block & platealuminum natural wood and wood composite
■ Material
52-200B/BL Double Edge - Solid CarbideUpcut Spiral Ball Nose
PART # CED CEL SHK DIA OAL
52-320B 3⁄8 11⁄8 3⁄8 3
52-360B 1⁄2 11⁄8 1⁄2 3
52-386B 5⁄8 21⁄4 5⁄8 4
52-397B 3⁄4 21⁄2 3⁄4 5
Designed for carving and modelingoperations. Their improved tip geometrygives a superior cut compared to mostballnose endmills.
PART # CED CEL SHK DIA OAL
52-235B 1⁄16 1⁄4 1⁄8 2
52-244B 1⁄8 1⁄2 1⁄8 2
52-240B 1⁄8 1⁄2 1⁄4 2
52-260B 3⁄163⁄4 1⁄4 2
52-280B 1⁄4 7⁄8 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
PART # CED CEL ERL SHK DIA OAL
52-320BL 3⁄8 11⁄4 25⁄8 3⁄8 4
52-360BL 1⁄2 11⁄2 35⁄8 1⁄2 5
52-386BL 5⁄8 21⁄2 35⁄8 5⁄8 5
52-397BL 3⁄4 3 45⁄8 3⁄4 6
PART # CED CEL ERL SHK DIA OAL
52-235BL 1⁄16 1⁄4 - 1⁄8 3
52-244BL 1⁄8 1⁄2 15⁄8 1⁄8 3
52-240BL 1⁄8 1⁄2 15⁄8 1⁄4 3
52-260BL 3⁄163⁄4 15⁄8 1⁄4 3
52-280BL 1⁄4 1 25⁄8 1⁄4 4
HELIX ANGLE ≈ 30°
EXTENDED LENGTH EXTENDED LENGTH
SW HW CW SP HP SSPASee SelectionGuide - pg. 2 - 12
■ Usage Natural wood, wood composites,plastic and solid surface
■ Material See Selection Guide - pg. 2 - 12
52-400 Double Edge - Solid CarbideUpcut Spiral Wood Rout
PART # CED CEL SHK DIA OAL
52-420 14 mm 50 mm 14 mm 88 mm
52-422 16 mm 55 mm 16 mm 100 mm
52-424 18 mm 60 mm 18 mm 120 mm
52-426 20 mm 60 mm 20 mm 120 mm
Designed for routing where upwardchip removal, tool rigidity, long life andhigh quality finish is desired.
PART # CED CEL SHK DIA OAL
52-410 4 mm 16 mm 6 mm 64 mm
52-411 5 mm 20 mm 6 mm 64 mm
52-412 6 mm 25 mm 6 mm 64 mm
52-414 8 mm 25 mm 8 mm 64 mm
52-416 10 mm 35 mm 10 mm 76 mm
52-418 12 mm 35 mm 12 mm 76 mm
HELIX ANGLE ≈ 30°
SW HW CW SP SSP
METRIC METRIC
■ Usage Foam
■ Material See Selection Guide - pg. 2 - 12
52-550 Double Edge - Solid CarbideFoam Cutters
PART # CED CEL SHK DIA OAL
52-564 1⁄4 21⁄4 1⁄4 4
52-570 5⁄16 31⁄8 5⁄16 41⁄2
52-574 3⁄8 31⁄2 3⁄8 5
Foam cutters for thick material withupward chip flow.
PART # CED CEL SHK DIA OAL
52-554 1⁄8 11⁄8 1⁄4 21⁄2
52-558 3⁄16 11⁄8 3⁄16 21⁄2
52-560 3⁄16 15⁄8 3⁄16 3
HELIX ANGLE ≈ 25°
FP
Page 79Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Soft and hard plastic, acrylic, nylon, ABS,PE, acetal, PET, HDPE, UHMW,polycarbonate and solid surface
■ Material See Selection Guide - pg. 2 - 12
52-600 Double Edge - Solid CarbideUpcut Spiral O Flute
PART # CED CEL SHK DIA OAL
52-652 1⁄2 15⁄8 1⁄2 31⁄2
52-655 1⁄2 21⁄8 1⁄2 41⁄2
52-660 5⁄8 21⁄8 5⁄8 5
52-664 3⁄4 31⁄8 3⁄4 6
Low helix geometry designed to cutsoft and hard plastic with a smoothfinish and upward chip flow.
PART # CED CEL SHK DIA OAL
52-622 1⁄4 3⁄8 1⁄4 21⁄2
52-624 1⁄4 3⁄4 1⁄4 21⁄2
52-638 3⁄8 1 3⁄8 3
52-650 1⁄2 11⁄8 1⁄2 31⁄2
HELIX ANGLE ≈ 11°
SP HP SSP
■ Usage Soft plastic, extruded acrylic, nylon, ABS,PE, acetal, PET, HDPE, UHMW,polycarbonate and solid surface.
■ Material See Selection Guide - pg. 2 - 12
52-700 Double Edge - Solid CarbideUpcut Spiral O Flute
PART # CED CEL SHK DIA OAL
52-742 12mm 35mm 12mm 100mm
52-744 12mm 45mm 12mm 100mm
52-746 12mm 55mm 12mm 100mm
52-752 16mm 45mm 16 mm 120mm
52-754 16mm 55mm 16mm 120mm
52-764 20mm 65mm 20mm 125mm
High helix geometry designed to cutsoft plastic with a smooth finish andupward chip flow. Special point geom-etry for improved bottom finish.
PART # CED CEL SHK DIA OAL
52-703 1⁄8 1⁄2 1⁄4 2
52-705 1⁄4 3⁄8 1⁄4 21⁄2
52-707 1⁄4 7⁄8 1⁄4 3
52-700 1⁄4 11⁄4 1⁄4 3
52-709 3⁄8 1 3⁄8 3
52-701 3⁄8 11⁄2 3⁄8 4
52-702 1⁄2 11⁄4 1⁄2 4
52-704 1⁄2 13⁄4 1⁄2 4
52-706 1⁄2 21⁄8 1⁄2 4
52-712 5⁄8 13⁄4 5⁄8 5
52-714 5⁄8 21⁄4 5⁄8 5
52-726 3⁄4 13⁄4 3⁄4 5
52-724 3⁄4 21⁄2 3⁄4 5
52-728 3⁄4 4 3⁄4 6
52-734 1 4 1 6
HELIX ANGLE ≈ 22°
METRIC
SP
NEW TOOLS in BOLD
Page 80
■ Usage Natural wood andwood composites
■ Material See Selection Guide - pg. 2 - 12
52-900 Double Edge - Solid CarbideUpcut Extreme Heavy Duty Standard
PART # CED CEL SHK DIA OAL
52-924 3⁄8 11⁄4 3⁄8 3
52-936 1⁄2 11⁄4 1⁄2 3
Developed for demanding applicationswhere upward chip removal, tool rigidityand long life are essential to success.
PART # CED CEL SHK DIA OAL
52-910 1⁄4 7⁄8 1⁄4 21⁄2
52-914 1⁄4 11⁄4 1⁄4 3
52-923 3⁄8 11⁄8 3⁄8 3
HELIX ANGLE ≈ 30°
SW HW CW
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
53-000 Three Edge - Solid CarbideStraight
PART # CED CEL SHK DIA OAL
53-080 1⁄4 3⁄4 1⁄4 21⁄2
Designed for routing extremely hardmaterials or when spindle RPM islower than normal for routing.
PART # CED CEL SHK DIA OAL
53-040 1⁄8 1⁄2 1⁄4 2
CP
CP
■ Usage Fiberglass
■ Material See Selection Guide - pg. 2 - 12
54-300 Four Edge - Solid CarbideDowncut Spiral
PART # CED CEL SHK DIA OAL
54-360 1⁄2 5⁄8 1⁄2 31⁄2
54-365 1⁄2 11⁄8 1⁄2 31⁄2
HELIX ANGLE ≈ 30°
Designed to be equally adaptable to lowor high spindle speed applications in anyCNC machining environment. The freecutting action of the tools provides forbetter finishes.
PART # CED CEL SHK DIA OAL
54-320 3⁄8 5⁄8 3⁄8 3
54-325 3⁄8 11⁄8 3⁄8 3
HELIX ANGLE ≈ 30°
Page 81Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
CP
■ Usage Fiberglass
■ Material See Selection Guide - pg. 2 - 12
55-300 Four Edge - Solid CarbideUpcut Spiral
PART # CED CEL SHK DIA OAL
55-360 1⁄2 5⁄8 1⁄2 31⁄2
55-365 1⁄2 11⁄8 1⁄2 31⁄2
HELIX ANGLE ≈ 30°
Designed to be equally adaptable to lowor high spindle speed applications inany CNC machining environment. Thefree cutting action of the tools providesfor better finishes.
PART # CED CEL SHK DIA OAL
55-320 3⁄8 5⁄8 3⁄8 3
55-325 3⁄8 11⁄8 3⁄8 3
HELIX ANGLE ≈ 30°
PART # CED CEL SHK DIA OAL
55-040 1⁄8 1⁄2 1⁄4 2
55-050 5⁄32 9⁄16 1⁄4 2
55-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 15°
PART # CED CEL SHK DIA OAL
54-040 1⁄8 1⁄2 1⁄4 2
54-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
UPCUT DOWNCUT
54-000 Four Edge - Solid Carbide55-000 Spiral
Equally adaptable to low or highspindle speed applications in anyCNC machining environment.The free cutting action of the tools provides for better finishes.
■ Usage Composite plastic
■ Material See Selection Guide - pg. 2 - 12
56-000 Double Edge - Solid CarbideStraight
PART # CED CEL SHK DIA OAL
56-090 9⁄32 3⁄4 3⁄8 21⁄2
56-100 5⁄16 13⁄16 3⁄8 21⁄2
56-120 3⁄8 7⁄8 3⁄8 21⁄2
56-140 7⁄16 1 1⁄2 3
56-160 1⁄2 1 1⁄2 3
Designed to rout composite plastic
PART # CED CEL SHK DIA OAL
56-040 1⁄8 1⁄2 1⁄4 2
56-050 5⁄32 9⁄16 1⁄4 2
56-060 3⁄16 5⁄8 1⁄4 2
56-070 7⁄32 5⁄8 1⁄4 21⁄2
56-080 1⁄4 3⁄4 1⁄4 21⁄2
56-084* 1⁄4 3⁄4 1⁄4 31⁄4
* These tools are designed and toleranced for air routers with guide bushings.
HP CP SSP FP
CP
■ Usage Fiberglass
■ Material See Selection Guide - pg. 2 - 12
Page 82
56-000P Double Edge - Solid CarbideStraight
Designed specifically to rout harder,more rigid plastics.
■ Usage Foam, fiberglass, phenolic, acrylic, nylon,PVC, ABS, acetal and solid surface
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
56-121 3⁄8 5⁄8 3⁄8 21⁄2
56-122 3⁄8 7⁄8 3⁄8 21⁄2
56-122L 3⁄8 7⁄8 3⁄8 21⁄2
56-124* 3⁄8 15⁄8 3⁄8 6
56-162 1⁄2 1 1⁄2 3
56-162L 1⁄2 1 1⁄2 3
56-164* 1⁄2 21⁄8 1⁄2 6
* These tools are designed and toleranced for Air Routers with guide
PART # CED CEL SHK DIA OAL
56-041 1⁄8 1⁄4 1⁄4 2
56-061 3⁄16 3⁄8 1⁄4 2
56-062 3⁄16 5⁄8 1⁄4 2
56-062L 3⁄16 5⁄8 1⁄4 2
56-063* 3⁄16 5⁄8 1⁄4 4
56-081 1⁄4 3⁄8 1⁄4 21⁄2
56-082 1⁄4 3⁄4 1⁄4 21⁄2
56-082L 1⁄4 3⁄4 1⁄4 21⁄2
56-086* 1⁄4 11⁄4 1⁄4 4
L = Left Hand Rotation
HP CP SSP FP
PART # CED CEL SHK DIA OAL
56-330 3⁄8 11⁄4 1⁄2 3
56-340 7⁄16 1 1⁄2 3
56-360 1⁄2 11⁄8 1⁄2 3
56-361(S) 1⁄2 11⁄8 1⁄2 3
56-362 1⁄2 11⁄4 1⁄2 31⁄2
56-365 1⁄2 15⁄8 1⁄2 31⁄2
56-370 17⁄32 11⁄8 1⁄2 3
56-385 5⁄8 21⁄8 5⁄8 4
56-390 3⁄4 15⁄8 3⁄4 4
56-395 3⁄4 21⁄8 3⁄4 4
(S) For Soft Woods
56-200 Double Edge - Solid CarbideStraight Wood Rout
Provides a superior finish in a varietyof wood materials and optimum cutterlife.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
56-240 1⁄8 1⁄2 1⁄4 2
56-250 5⁄32 5⁄8 1⁄4 2
56-260 3⁄16 3⁄4 1⁄4 2
56-270 7⁄32 3⁄4 1⁄4 21⁄2
56-280 1⁄4 7⁄8 1⁄4 21⁄2
56-285 1⁄4 1 1⁄4 21⁄2
56-287 1⁄4 11⁄8 1⁄4 3
56-290 9⁄32 1 5⁄16 21⁄2
56-300 5⁄16 11⁄8 5⁄16 3
56-310 5⁄16 11⁄8 1⁄2 3
56-320 3⁄8 11⁄8 3⁄8 3
56-325 3⁄8 11⁄4 3⁄8 3
SW CWHW
56-430 Double Edge - Solid CarbideStraight O Flute
Designed with free cutting O flutegeometry along with a double flutedesign for smooth finish.
■ Usage Polycarbonate, ABS, HIPS, HDPE,PET, acrylic, polystyrene, polypropylene,PE, PVC, acetal, UHMW
■ Material See Selection Guide - pg. 2 - 12SP HP
PART # CED CEL SHK DIA OAL
56-436 10 mm 35 mm 10 mm 88 mm
56-438 12 mm 35 mm 12 mm 88 mm
PART # CED CEL SHK DIA OAL
56-430 4 mm 16 mm 6 mm 64 mm
56-431 5 mm 20 mm 6 mm 64 mm
56-432 6 mm 25 mm 6 mm 64 mm
56-434 8 mm 25 mm 8 mm 76 mm
METRIC METRIC
Page 83Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
56-450 Double Edge - Solid CarbideStraight
Designed specifically to rout harder,more rigid plastics
■ Usage Phenolic, acrylic, nylon, PVC, ABS, acetaland solid surface
■ Material See Selection Guide - pg. 2 - 12HP CP SSP
PART # CED CEL SHK DIA OAL
56-454 8 mm 25 mm 8 mm 76 mm
56-456 10 mm 35 mm 10 mm 88 mm
56-458 12 mm 35 mm 12 mm 88 mm
* These tools are designed and toleranced for Air Routers with guide
PART # CED CEL SHK DIA OAL
56-450 4 mm 16 mm 6 mm 64 mm
56-451 5 mm 20 mm 6 mm 64 mm
56-452 6 mm 25 mm 6 mm 64 mm
METRIC METRIC
56-600 Double Edge - Solid CarbideO Flute Straight
Designed with free cutting O flutegeometry along with a double flutedesign for smooth finish.
■ Usage Polycarbonate, ABS, HIPS, HDPE, PET,acrylic, polystyrene, polypropylene, PE,PVC, acetal, UHMW
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
56-626 1⁄4 1 1⁄4 31⁄4
56-628 1⁄4 11⁄4 1⁄4 4
56-638 3⁄8 7⁄8 3⁄8 21⁄2
56-639 3⁄8 1 3⁄8 4
56-650 1⁄2 1 1⁄2 3
56-652 1⁄2 1 1⁄2 4
56-654 1⁄2 13⁄4 1⁄2 4
56-655 1⁄2 21⁄8 1⁄2 6
L = Left Hand Rotation
PART # CED CEL SHK DIA OAL
56-610 1⁄8 5⁄16 1⁄4 2
56-612 1⁄8 1⁄2 1⁄4 2
56-614 1⁄8 5⁄8 1⁄4 4
56-616 3⁄16 3⁄8 1⁄4 2
56-618 3⁄16 5⁄8 1⁄4 2
56-620 3⁄16 1 1⁄4 4
56-624 1⁄4 3⁄8 1⁄4 21⁄2
56-625 1⁄4 1 1⁄4 21⁄2
56-625L 1⁄4 1 1⁄4 21⁄2
SP HP
57-000 Double Edge - Solid CarbideDowncut Spiral
Designed as a general purposespiral with several times the life oftheir high speed counterparts.They are used when a downwardchipflow action is preferred.
■ Usage Aluminum, composite plastic andsolid surface
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
57-040 1⁄8 1⁄2 1⁄4 2
57-050 5⁄32 9⁄16 1⁄4 2
57-060 3⁄16 5⁄8 1⁄4 2
57-080 1⁄4 3⁄4 1⁄4 21⁄2
57-090 9⁄32 3⁄4 3⁄8 21⁄2
HELIX ANGLE ≈ 30°
PART # CED CEL SHK DIA OAL
57-100 5⁄16 13⁄16 3⁄8 21⁄2
57-120 3⁄8 7⁄8 3⁄8 21⁄2
57-140 7⁄16 1 1⁄2 3
57-160 1⁄2 1 1⁄2 3
HELIX ANGLE ≈ 30°
CP SSPA
Page 84
57-200 Double Edge - Solid CarbideDowncut Spiral Wood Rout
PART # CED CEL SHK DIA OAL
57-330 3⁄8 11⁄4 1⁄2 3
57-340 7⁄16 1 1⁄2 3
57-360 1⁄2 11⁄8 1⁄2 3
57-361(S) 1⁄2 11⁄8 1⁄2 3
57-362 1⁄2 11⁄4 1⁄2 31⁄2
57-365 1⁄2 15⁄8 1⁄2 31⁄2
57-365L 1⁄2 15⁄8 1⁄2 31⁄2
57-366(S) 1⁄2 15⁄8 1⁄2 31⁄2
57-367 1⁄2 21⁄8 1⁄2 4
57-370 17⁄32 11⁄8 1⁄2 3
57-380 5⁄8 15⁄8 5⁄8 31⁄2
57-385 5⁄8 21⁄8 5⁄8 4
57-385L 5⁄8 21⁄8 5⁄8 4
57-390 3⁄4 15⁄8 3⁄4 4
57-395 3⁄4 21⁄8 3⁄4 4
57-395L 3⁄4 21⁄8 3⁄4 4
Designed for routing where downwardchip removal, tool rigidity, long life, andhigh quality finish is desired.
■ Usage Natural wood, wood composites,solid surface
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
57-244 1⁄8 1⁄2 1⁄8 2
57-240 1⁄8 1⁄2 1⁄4 2
57-240L 1⁄8 1⁄2 1⁄4 2
57-251 5⁄32 1⁄2 1⁄4 21⁄2
57-250 5⁄32 5⁄8 1⁄4 2
57-260 3⁄16 3⁄4 1⁄4 2
57-260L 3⁄16 3⁄4 1⁄4 2
57-261 3⁄16 3⁄4 1⁄4 21⁄2
57-270 7⁄32 3⁄4 1⁄4 21⁄2
57-271 7⁄32 1 1⁄4 21⁄2
57-280 1⁄4 7⁄8 1⁄4 21⁄2
57-281(S) 1⁄4 7⁄8 1⁄4 21⁄2
57-285 1⁄4 1 1⁄4 21⁄2
57-285L 1⁄4 1 1⁄4 21⁄2
57-287 1⁄4 11⁄8 1⁄4 3
57-290 9⁄32 1 5⁄16 21⁄2
57-300 5⁄16 11⁄8 5⁄16 3
57-310 5⁄16 11⁄8 1⁄2 3
57-310L 5⁄16 11⁄8 1⁄2 3
57-318* 3⁄8 1 3⁄8 3
57-320 3⁄8 11⁄8 3⁄8 3
57-325 3⁄8 11⁄4 3⁄8 3
57-325L 3⁄8 11⁄4 3⁄8 3
HELIX ANGLE ≈ 30° L = Left Hand Rotation
* Special Point (S) = Soft Wood Geometry
SW HW CW SSP
57-400 Double Edge - Solid CarbideDowncut Spiral Wood Rout
Designed for routing where downwardchip removal, tool rigidity, long life, andhigh quality finish is desired.
■ Usage Natural wood, wood composites and solid surface
■ Material See Selection Guide - pg. 2 - 12SW HW CW SSP
PART # CED CEL SHK DIA OAL
57-420 14 mm 50 mm 14 mm 88 mm
57-424 18 mm 60 mm 18 mm 120 mm
57-426 20 mm 60 mm 20 mm 120 mm
PART # CED CEL SHK DIA OAL
57-410 4 mm 16 mm 6 mm 64 mm
57-411 5 mm 20 mm 6 mm 64 mm
57-412 6 mm 25 mm 6 mm 64 mm
57-414 8 mm 25 mm 8 mm 64 mm
57-416 10 mm 35 mm 10 mm 76 mm
57-418 12 mm 35 mm 12 mm 76 mm
HELIX ANGLE ≈ 30°
METRIC METRIC
Page 85Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
57-600 Double Edge - Solid CarbideDowncut Spiral O Flute
Designed to cut plastic with a smoothfinish and downward chip flow.
■ Usage Acrylic, nylon, ABS, PE, acetal, PET,HDPE, UHMW, polycarbonate andsolid surface
■ Material See Selection Guide - pg. 2 - 12
METRIC
PART # CED CEL SHK DIA OAL
57-623 1⁄4 3⁄8 1⁄4 21⁄2
57-625 1⁄4 3⁄4 1⁄4 21⁄2
57-637 3⁄8 1 3⁄8 3
57-651 1⁄2 11⁄8 1⁄2 31⁄2
HELIX ANGLE ≈ 10-11°
PART # CED CEL SHK DIA OAL
57-627 6mm 25mm 6mm 64mm
57-639 8mm 25mm 8mm 76mm
57-643 10mm 25mm 10mm 76mm
57-645 12mm 35mm 12mm 88mm
SP HP SSP
57-900 Double Edge - Solid CarbideDowncut Extreme Heavy Duty Standard
PART # CED CEL SHK DIA OAL
57-924 3⁄8 11⁄4 3⁄8 3
57-936 1⁄2 11⁄4 1⁄2 3
57-940 1⁄2 15⁄8 1⁄2 31⁄2
Designed for routing where extremeloads are placed upon the cuttingtools and when extra part hold downis required.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
57-910 1⁄4 7⁄8 1⁄4 21⁄2
57-921 3⁄8 7⁄8 3⁄8 3
57-923 3⁄8 11⁄8 3⁄8 3
HELIX ANGLE ≈ 30°
SW HW CW
58-000 Three Edge - Solid Carbide59-000 Spiral
Designed to rout difficult to cutmaterial when horsepower or spindlespeed may be a problem. Theyemploy upcut router geometry ratherthan end mill geometry for better chipremoval and smoother finish.
■ Usage Composites, fiberglass and phenolic
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
58-040 1⁄8 1⁄2 1⁄4 2
58-060 3⁄16 5⁄8 1⁄4 2
58-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
PART # CED CEL SHK DIA OAL
59-040 1⁄8 1⁄2 1⁄4 2
59-060 3⁄16 5⁄8 1⁄4 2
59-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
CP
Page 86
60-000 Three Edge - Solid CarbideHigh Helix Hogger
Designed with unique scallopedcutting edge design for extremely fastmachining and roughing. Faster chipremoval with upcuts. Better hold downwith downcuts.
■ Usage Natural wood & wood composites,hard & soft plastic and plastic composites
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
60-002 3⁄8 11⁄8 3⁄8 31⁄2
60-006 1⁄2 11⁄8 1⁄2 31⁄2
60-008 1⁄2 15⁄8 1⁄2 4
60-010 5⁄8 15⁄8 5⁄8 4
60-012 5⁄8 21⁄8 5⁄8 5
60-018 3⁄4 15⁄8 3⁄4 4
60-020 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-001 3⁄8 11⁄8 3⁄8 31⁄2
60-005 1⁄2 11⁄8 1⁄2 31⁄2
60-007 1⁄2 15⁄8 1⁄2 4
60-009 5⁄8 15⁄8 5⁄8 4
60-011 5⁄8 21⁄8 5⁄8 5
60-017 3⁄4 15⁄8 3⁄4 4
60-019 3⁄4 21⁄8 3⁄4 5
HELIX ANGLE ≈ 30°
UPCUT METRIC DOWNCUT METRIC
PART # CED CEL SHK DIA OAL
60-004 12mm 25mm 12mm 76mm
60-014 16mm 55mm 16mm 120mm
60-016 18mm 60mm 18mm 120mm
PART # CED CEL SHK DIA OAL
60-003 12mm 25mm 12mm 76mm
60-013 16mm 55mm 16mm 120mm
60-015 18mm 60mm 18mm 120mm
HELIX ANGLE ≈ 30°
60-000 Three Edge - Solid CarbideLow Helix Hogger
Designed with unique scallopedcutting edge design for extremelyfast machining and roughing. Lowerhorsepower and longer tool life areadditional advantages.
■ Usage Natural wood & wood composites,hard & soft plastic and plastic composites
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
60-038 3⁄8 11⁄8 3⁄8 31⁄2
60-054 1⁄2 11⁄8 1⁄2 31⁄2
60-052 1⁄2 15⁄8 1⁄2 4
60-066 5⁄8 15⁄8 5⁄8 4
60-062 5⁄8 21⁄8 5⁄8 5
60-074 3⁄4 15⁄8 3⁄4 5
60-072 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-037 3⁄8 11⁄8 3⁄8 31⁄2
60-053 1⁄2 11⁄8 1⁄2 31⁄2
60-051 1⁄2 15⁄8 1⁄2 4
60-061 5⁄8 21⁄8 5⁄8 5
60-073 3⁄4 15⁄8 3⁄4 4
60-071 3⁄4 21⁄8 3⁄4 5
HELIX ANGLE ≈ 10°
UPCUT METRIC DOWNCUT METRIC
PART # CED CEL SHK DIA OAL
60-056 12mm 25mm 12mm 76mm
60-064 16mm 55mm 16mm 120mm
60-076 18mm 60mm 18mm 120mm
PART # CED CEL SHK DIA OAL
60-055 12mm 25mm 12mm 76mm
60-063 16mm 55mm 16mm 120mm
60-075 18mm 60mm 18mm 120mm
HELIX ANGLE ≈ 10°
SW HW CW
SW HW CW
Page 87Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
60-090 Three Edge - Solid CarbideUpcut Lock Mortise
PART # CED CEL MAX DOC SHK DIA OAL
60-091 16 mm 50 mm 114 mm 16 mm 170 mm
The scalloped upcut cutting edgedesign and extra spinback providefast material removal in deep cutsfor horizontal and vertical lockmortise routing.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL MAX DOC SHK DIA OAL
60-090 5⁄8 2 41⁄2 5⁄8 61⁄2
HELIX ANGLE ≈ 30°
SW HW CW MTDT
METRIC
LW
PART # CED CEL SHK DIA OAL
60-132 6mm 25mm 6mm 64mm
60-134 8mm 25mm 8mm 64mm
60-136 10mm 35mm 10mm 76mm
60-138 12mm 35mm 12mm 76mm
60-142 16mm 55mm 16mm 100mm
60-122 = Hard surface double laminate geometry.60-162 = Hard surface double laminate geometry.
PART # CED CEL SHK DIA OAL
60-102 1⁄8 3⁄8 1⁄4 21⁄2
60-106 3⁄16 5⁄8 1⁄4 21⁄2
60-110 1⁄4 7⁄8 1⁄4 21⁄2
60-122 3⁄8 1 3⁄8 3
60-120 3⁄8 11⁄8 3⁄8 3
60-120L 3⁄8 11⁄8 3⁄8 3
60-160 1⁄2 1 1⁄2 3
60-162* 1⁄2 1 1⁄2 3
60-167 1⁄2 11⁄8 1⁄2 3
60-170 1⁄2 13⁄8 1⁄2 31⁄2
60-165 1⁄2 15⁄8 1⁄2 31⁄2
60-165L 1⁄2 15⁄8 1⁄2 31⁄2
60-185 5⁄8 21⁄4 5⁄8 4
HELIX ANGLE ≈ 30°*HELIX ANGLE ≈ 20°
60-100SE Single Edge - Solid CarbideCompression Spiral
Compression design for fast feed ratesand optimum edge finish on both sidesof laminated materials. Designed forlow speed applications.
■ Usage Double sided laminated, veneered, naturalwood and wood composites
■ Material See Selection Guide - pg. 2 - 12CWHW
METRIC
Page 88
■ Usage Double sided laminated, veneered, naturalwood and wood composites
■ Material See Selection Guide - pg. 2 - 12LW
60-100DE Double Edge - Solid CarbideCompression Spiral
Compression design for fast feed ratesand optimum edge finish on both sidesof laminated materials.
CWHW
PART # CED CEL SHK DIA OAL
60-133 6 mm 25 mm 6 mm 64 mm
60-135 8 mm 25 mm 8 mm 64 mm
60-137 10 mm 35 mm 10 mm 76 mm
60-139 12 mm 35 mm 12 mm 76 mm
60-140 20 mm 50 mm 20 mm 100 mm
HELIX ANGLE ≈ 30°
L = Left Hand Rotation
PART # CED CEL SHK DIA OAL
60-112 1⁄4 7⁄8 1⁄4 21⁄2
60-124 3⁄8 11⁄8 3⁄8 3
60-164 1⁄2 1 1⁄2 3
60-171 1⁄2 13⁄8 1⁄2 31⁄2
60-169 1⁄2 11⁄8 1⁄2 3
60-172 1⁄2 15⁄8 1⁄2 4
60-172L 1⁄2 15⁄8 1⁄2 4
60-186 5⁄8 21⁄4 5⁄8 5
60-196 3⁄4 17⁄8 3⁄4 4
60-198 3⁄4 21⁄2 3⁄4 5
60-198L 3⁄4 21⁄2 3⁄4 5
METRIC
60-100C Double Edge - Solid CarbideChipbreaker/Finisher CompressionSpiral
PART # CED CEL SHK DIA OAL
60-135C 8 mm 25 mm 8 mm 64 mm
60-137C 10 mm 35 mm 10 mm 76 mm
60-139C 12 mm 35 mm 12 mm 76 mm
60-140C 20 mm 50 mm 20 mm 100 mm
Designed to give the optimum edgefinish of the compression spiral bitsalong with the increased feed ratesof the chipbreaker/finisher design.
■ Usage Double sided laminated,veneered, natural woodand wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
60-123C 3⁄8 7⁄8 3⁄8 3
60-124C 3⁄8 11⁄8 3⁄8 3
60-163C 1⁄2 7⁄8 1⁄2 3
60-164C 1⁄2 1 1⁄2 3
60-169C 1⁄2 11⁄8 1⁄2 3
60-171C 1⁄2 13⁄8 1⁄2 31⁄2
60-172C 1⁄2 15⁄8 1⁄2 4
60-186C 5⁄8 21⁄4 5⁄8 5
60-196C 3⁄4 17⁄8 3⁄4 4
HELIX ANGLE ≈ 30°
HW CW LW
METRIC
Page 89Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
LW
PART # CED CEL SHK DIA OAL
60-175 1⁄2 15⁄8 1⁄2 31⁄2
60-197 3⁄4 2 3⁄4 4
PART # CED CEL SHK DIA OAL
60-125 3⁄8 11⁄8 3⁄8 3
60-174 1⁄2 11⁄8 1⁄2 3
HELIX ANGLE ≈ 30°
60-100TE Three Edge - Solid CarbideCompression Spiral
Compression design for ultra high feedrates and optimum edge finish on bothsides of laminated material.
■ Usage Double sided laminated, veneered, naturalwood and wood composites
■ Material See Selection Guide - pg. 2 - 12CWHW
Single EdgeHW CW LWMT
DT
DOUBLE EDGE
PART # CED CEL UPCUT CEL SHK DIA OAL
60-113 1⁄4 7⁄8 0.188 1⁄4 21⁄2
60-123 3⁄8 7⁄8 0.188 3⁄8 3
60-127L 3⁄8 11⁄8 0.188 3⁄8 3
60-163 1⁄2 7⁄8 0.200 1⁄2 3
60-173 1⁄2 13⁄8 0.200 1⁄2 31⁄2
60-173L 1⁄2 13⁄8 0.200 1⁄2 31⁄2
PART # CED CEL UPCUT CEL SHK DIA OAL
60-111 1⁄4 7⁄8 0.175 1⁄4 21⁄2
60-121 3⁄8 7⁄8 0.188 3⁄8 3
60-161 1⁄2 7⁄8 0.200 1⁄2 3
60-161L 1⁄2 7⁄8 0.200 1⁄2 3
60-166 1⁄2 15⁄8 0.200 1⁄2 31⁄2
HELIX ANGLE ≈ 30°L = Left Hand Rotation
SINGLE EDGE
Double Edge Three Edge
THREE EDGE
PART # CED CEL UPCUT CEL SHK DIA OAL
60-126 3⁄8 7⁄8 0.200 3⁄8 3
60-176 1⁄2 7⁄8 0.200 1⁄2 3
60-177 1⁄2 13⁄8 0.200 1⁄2 31⁄2
60-199 3⁄4 2 0.200 3⁄4 4
60-100M Single, Double &Three Edge - Solid CarbideMortise Compression Spiral
Compression design for fast feed and excellent finish with shortupcut to allow mortise cut with downcut action.
■ Usage Double sided laminated, veneered, naturalwood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL UPCUT CEL SHK DIA OAL
60-152 6mm 22mm 4mm 6mm 64mm
60-154 8mm 22mm 4mm 8mm 64mm
60-156 10mm 22mm 4mm 10mm 76mm
60-158 12mm 22mm 4mm 12mm 76mm
HELIX ANGLE ≈ 30°L = Left Hand Rotation
SINGLE EDGE METRIC
DOUBLE EDGE METRIC
PART # CED CEL UPCUT CEL SHK DIA OAL
60-155 10mm 22mm 4mm 10mm 76mm
60-157 12mm 22mm 4mm 12mm 76mm
Page 90
60-100MW Single, Double & Three Edge -Solid Carbide Max LifeCompression Spiral
Designed for maximum life when cutting in high-wear applications.Unique geometries and carbidesimprove the wear characteristics ofthe tool under abrasive applicationswith superior part finish.
■ Usage Double sided laminatedand veneered materials
■ Material See Selection Guide - pg. 2 - 12LW
THREE EDGE
PART # CED CEL SHK DIA OAL
60-126MW* 3⁄8 7⁄8 3⁄8 3
*MORTISE COMPRESSION
PART # CED CEL SHK DIA OAL
60-120MW* 3⁄8 11⁄8 3⁄8 3
60-167MW* 1⁄2 11⁄8 1⁄2 3
HELIX ANGLE ≈ 30° *MORTISE COMPRESSION
SINGLE EDGE
Double Edge
Three Edge
PART # CED CEL SHK DIA OAL
60-123MW* 3⁄8 7⁄8 3⁄8 3
60-124MW 3⁄8 11⁄8 3⁄8 3
60-163MW* 1⁄2 7⁄8 1⁄2 3
60-169MW 1⁄2 11⁄8 1⁄2 3
60-171MW 1⁄2 13⁄8 1⁄2 31⁄2
60-172MW 1⁄2 15⁄8 1⁄2 4
60-173MW 1⁄2 13⁄8 1⁄2 31⁄2
60-179MW 1⁄2 11⁄2 1⁄2 4
60-181MW 1⁄2 21⁄8 1⁄2 5
60-196MW 3⁄4 17⁄8 3⁄4 4
60-194MW 3⁄4 21⁄4 3⁄4 5
HELIX ANGLE ≈ 30° *MORTISE COMPRESSION
DOUBLE EDGE
Single Edge
60-200 Three Edge - Solid CarbideLow Helix Finisher
Designed for perfect balanceand ultra smooth finish over awide speed range.
■ Usage Natural wood, plastic, compositeplastic and solid surface
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
60-239 1⁄4 3⁄8 1⁄4 3
60-241 1⁄4 7⁄8 1⁄4 3
60-243 3⁄8 5⁄8 3⁄8 3
60-245 3⁄8 11⁄8 3⁄8 3
60-249 1⁄2 11⁄8 1⁄2 31⁄2
60-253 1⁄2 15⁄8 1⁄2 4
60-251 1⁄2 21⁄8 1⁄2 41⁄2
60-269 3⁄4 15⁄8 3⁄4 4
60-271 3⁄4 21⁄8 3⁄4 5
60-277 3⁄4 31⁄8 3⁄4 6
HELIX ANGLE ≈ 10°
PART # CED CEL SHK DIA OAL
60-240 1⁄4 3⁄8 1⁄4 3
60-242 1⁄4 7⁄8 1⁄4 3
60-244 3⁄8 5⁄8 3⁄8 3
60-246 3⁄8 11⁄8 3⁄8 3
60-250 1⁄2 11⁄8 1⁄2 31⁄2
60-254 1⁄2 15⁄8 1⁄2 4
60-252 1⁄2 21⁄8 1⁄2 41⁄2
60-270 3⁄4 15⁄8 3⁄4 4
60-272 3⁄4 21⁄8 3⁄4 5
60-278 3⁄4 31⁄8 3⁄4 6
HELIX ANGLE ≈ 10°
SW HW CW HP SSP
MAX
Page 91Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
DOWNCUT
PART # CED CEL SHK DIA OAL
60-308 3⁄8 11⁄8 3⁄8 3
60-312 1⁄2 11⁄8 1⁄2 3
60-314 1⁄2 15⁄8 1⁄2 31⁄2
60-318 1⁄2 17⁄8 1⁄2 31⁄2
60-316 1⁄2 21⁄8 1⁄2 4
60-322 5⁄8 21⁄8 5⁄8 4
60-326 3⁄4 21⁄8 3⁄4 4
PART # CED CEL SHK DIA OAL
60-307 3⁄8 11⁄8 3⁄8 3
60-311 1⁄2 11⁄8 1⁄2 3
60-313 1⁄2 15⁄8 1⁄2 31⁄2
60-317 1⁄2 17⁄8 1⁄2 31⁄2
60-315 1⁄2 21⁄8 1⁄2 4
60-321 5⁄8 21⁄8 5⁄8 4
60-325 3⁄4 21⁄8 3⁄4 4
HELIX ANGLE ≈ 30°
UPCUT
60-300 Double Edge - Solid CarbideChipbreaker Finisher
For faster feed rates than a conventional two flute with a smooth finish.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12CWHW
DOWNCUT
PART # CED CEL SHK DIA OAL
60-338 3⁄8 11⁄8 3⁄8 3
60-350 1⁄2 11⁄8 1⁄2 3
60-354 1⁄2 13⁄8 1⁄2 31⁄2
60-352 1⁄2 15⁄8 1⁄2 31⁄2
60-360 5⁄8 15⁄8 5⁄8 4
60-370 3⁄4 15⁄8 3⁄4 4
60-372 3⁄4 21⁄4 3⁄4 5
60-374 3⁄4 31⁄8 3⁄4 6
PART # CED CEL SHK DIA OAL
60-337 3⁄8 11⁄8 3⁄8 3
60-351 1⁄2 11⁄8 1⁄2 3
60-355 1⁄2 13⁄8 1⁄2 31⁄2
60-353 1⁄2 15⁄8 1⁄2 31⁄2
60-361 5⁄8 15⁄8 5⁄8 4
60-371 3⁄4 15⁄8 3⁄4 4
60-373 3⁄4 21⁄4 3⁄4 4
60-375 3⁄4 31⁄8 3⁄4 6
HELIX ANGLE ≈ 30°
UPCUT
60-350 Three Edge - Solid CarbideChipbreaker Finisher
For additional balance at fast feedrates with a smooth finish.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
DOWNCUT METRIC
PART # CED CEL SHK DIA OAL
60-412 8 mm 25 mm 8 mm 64 mm
60-414 10 mm 35 mm 10 mm 76 mm
60-416 12 mm 35 mm 12 mm 76 mm
60-418 16 mm 55 mm 16 mm 100 mm
60-420 18 mm 60 mm 18 mm 120 mm
PART # CED CEL SHK DIA OAL
60-411 8 mm 25 mm 8 mm 64 mm
60-413 10 mm 35 mm 10 mm 76 mm
60-415 12 mm 35 mm 12 mm 76 mm
60-417 16 mm 55 mm 16 mm 100 mm
60-419 18 mm 60 mm 18 mm 120 mm
HELIX ANGLE ≈ 30°
UPCUT METRIC
60-400 Double Edge - Solid CarbideChipbreaker Finisher
For faster feed rates than a conventional two flute with a smooth finish.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
Page 92
LW
PART # CED CEL SHK DIA OAL
60-572 1⁄2 15⁄8 1⁄2 4
60-586 5⁄8 21⁄4 5⁄8 5
60-598 3⁄4 21⁄2 3⁄4 5
PART # CED CEL SHK DIA OAL
60-564 1⁄2 1 1⁄2 3
60-569 1⁄2 11⁄8 1⁄2 3
60-571 1⁄2 13⁄8 1⁄2 31⁄2
HELIX ANGLE ≈ 30°
60-500 Four Edge - Solid CarbideCompression Spiral
The ultimate in compression spiraltooling, these tools are designed torun on the newest generation CNCrouters. They produce extremely finefinishes at high feed rates.
■ Usage Double sided laminated and veneered,natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
DOWNCUT METRIC
PART # CED CEL SHK DIA OAL
60-432 8 mm 25 mm 8 mm 64 mm
60-434 10 mm 35 mm 10 mm 76 mm
60-436 12 mm 35 mm 12 mm 76 mm
60-438 16 mm 55 mm 16 mm 100 mm
60-440 18 mm 60 mm 18 mm 120 mm
PART # CED CEL SHK DIA OAL
60-431 8 mm 25 mm 8 mm 64 mm
60-433 10 mm 35 mm 10 mm 76 mm
60-435 12 mm 35 mm 12 mm 76 mm
60-437 16 mm 55 mm 16 mm 100 mm
60-439 18 mm 60 mm 18 mm 120 mm
HELIX ANGLE ≈ 30°
UPCUT METRIC
60-430 Three Edge - Solid CarbideChipbreaker Finisher
For additional balance at fast feedrates with a smooth finish.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
60-470 Three Edge - Solid CarbideLow Helix Finisher
Designed for perfect balanceand ultra smooth finish over awide speed range.
■ Usage Natural wood, wood, plastic, compositeplastic and solid surface
■ Material See Selection Guide - pg. 2 - 12
UPCUT METRIC DOWNCUT METRIC
PART # CED CEL SHK DIA OAL
60-482 6mm 25mm 6mm 76mm
60-472 8mm 25mm 8mm 76mm
60-474 10mm 35mm 10mm 76mm
60-476 12mm 35mm 12mm 88mm
60-484 14mm 45mm 14mm 110mm
60-478 16mm 55mm 16mm 120mm
60-480 18mm 60mm 18mm 120mm
HELIX ANGLE ≈ 10°
PART # CED CEL SHK DIA OAL
60-481 6mm 25mm 6mm 76mm
60-471 8mm 25mm 8mm 76mm
60-473 10mm 35mm 10mm 76mm
60-475 12mm 35mm 12mm 88mm
60-483 14mm 45mm 14mm 110mm
60-477 16mm 55mm 16mm 120mm
60-479 18mm 60mm 18mm 120mm
HELIX ANGLE ≈ 10°
HW HPCP SSP
Page 93Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
SW HW CW LWMTDT
PART # CED CEL UPCUT CEL SHK DIA OAL
60-573 1⁄2 13⁄8 0.200 1⁄2 31⁄2
PART # CED CEL UPCUT CEL SHK DIA OAL
60-563 1⁄2 7⁄8 0.200 1⁄2 3
HELIX ANGLE ≈ 30°
60-500M Four Edge - Solid CarbideMortise Compression Spiral
Compression design for fast feed and excellent finish with short upcut to allow mortise cuts with downcut action.
■ Usage Double sided laminated and veneered,natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
60-686 5⁄8 21⁄4 5⁄8 5
60-696 3⁄4 17⁄8 3⁄4 4
60-698 3⁄4 21⁄2 3⁄4 5
PART # CED CEL SHK DIA OAL
60-664 1⁄2 1 1⁄2 3
60-669 1⁄2 11⁄8 1⁄2 3
60-671 1⁄2 13⁄8 1⁄2 31⁄2
60-672 1⁄2 15⁄8 1⁄2 4
HELIX ANGLE ≈ 30°
60-600 Four Edge - Solid CarbideHigh Velocity CompressionSpiral
Combine a roughing and finishing cutin one tool for rapid feed rates with agood finish.
■ Usage High velocity routing of double sided laminated and veneered, natural woodand wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW LW
PART # CED CEL SHK DIA OAL
60-719 1⁄2 21⁄8 1⁄2 41⁄2
60-731 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-711 1⁄2 11⁄8 1⁄2 31⁄2
60-715 1⁄2 15⁄8 1⁄2 4
HELIX ANGLE ≈ 30°
60-700 Four Edge - Solid CarbideHigh Velocity Upcut Spiral
Combine a roughing and finishing cutwith upcut cutting action in one tool forrapid feed rates with a good finish.
■ Usage High velocity routing of natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
Page 94
PART # CED CEL SHK DIA OAL
60-720 5⁄8 21⁄8 5⁄8 5
60-730 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-710 1⁄2 11⁄8 1⁄2 31⁄2
60-714 1⁄2 15⁄8 1⁄2 4
60-718 1⁄2 21⁄8 1⁄2 41⁄2
HELIX ANGLE ≈ 30°
60-700 Four Edge - Solid CarbideHigh Velocity Downcut Spiral
Combine a roughing and finishing cutwith downcut cutting action in one toolfor rapid feed rates with a good finish.
■ Usage High velocity routing of natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
60-800 Double Edge - Solid CarbideRougher
Designed for use when faster feedrates cannot be achieved, or on lowhorsepower machines.
■ Usage Wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
60-816 3⁄8 13⁄8 3⁄8 31⁄2
60-826 1⁄2 13⁄8 1⁄2 31⁄2
60-830 1⁄2 17⁄8 1⁄2 4
60-842 5⁄8 25⁄8 5⁄8 5
60-848 3⁄4 27⁄8 3⁄4 6
PART # CED CEL SHK DIA OAL
60-815 3⁄8 13⁄8 3⁄8 31⁄2
60-825 1⁄2 13⁄8 1⁄2 31⁄2
60-829 1⁄2 17⁄8 1⁄2 4
60-841 5⁄8 25⁄8 5⁄8 5
60-847 3⁄4 27⁄8 3⁄4 6
HELIX ANGLE ≈ 20°
SW CWHW
60-850 Double Edge - Solid CarbideRougher Compression
Compression Rougher designallows for increased feedrates overa standard compression and providesa clean edge on the top and bottomsurfaces. This tool excels in single orstack sheet plywood where the edgeis hidden or covered.
■ Usage Double sided laminated, veneered,natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
60-867 1⁄2 13⁄4 1⁄2 5
PART # CED CEL SHK DIA OAL
60-855* 3⁄8 11⁄4 3⁄8 31⁄2
60-865* 1⁄2 11⁄4 1⁄2 5
HELIX ANGLE ≈ 30° * = Mortise Compression
LW CWHW
Page 95Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
60-900 Three Edge - Solid CarbideExtreme Heavy Duty Hogger
Designed for heavy material removaloperations where the cutter is subjectto excessive cutting forces and finishis not a primary concern.
■ Usage Natural wood, wood composites, hardand soft plastic and plastic composites
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
PART # CED CEL SHK DIA OAL
60-902 3⁄8 11⁄8 3⁄8 3
60-906 1⁄2 11⁄8 1⁄2 3
60-908 1⁄2 15⁄8 1⁄2 31⁄2
60-910 1⁄2 21⁄8 1⁄2 4
60-916 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-901 3⁄8 11⁄8 3⁄8 3
60-905 1⁄2 11⁄8 1⁄2 3
60-907 1⁄2 15⁄8 1⁄2 31⁄2
60-909 1⁄2 21⁄8 1⁄2 4
60-915 3⁄4 21⁄8 3⁄4 5
HELIX ANGLE ≈ 30°
DOWNCUT
PART # CED CEL SHK DIA OAL
60-950 3⁄8 11⁄8 3⁄8 3
60-954 1⁄2 11⁄8 1⁄2 3
60-956 1⁄2 15⁄8 1⁄2 31⁄2
60-958 1⁄2 21⁄8 1⁄2 4
60-966 3⁄4 21⁄8 3⁄4 5
PART # CED CEL SHK DIA OAL
60-951 3⁄8 11⁄8 3⁄8 3
60-955 1⁄2 11⁄8 1⁄2 3
60-957 1⁄2 15⁄8 1⁄2 31⁄2
60-959 1⁄2 21⁄8 1⁄2 4
60-965 3⁄4 21⁄8 3⁄4 5
HELIX ANGLE ≈ 30°
UPCUT
60-950 Double Edge - Solid CarbideExtreme Heavy DutyChipbreaker/Finisher
Designed to be fed very fast whilewithstanding excessive cutting forcesand at the same time leaving asmooth finish.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
SW CWHW
61-000 Single Edge - Solid CarbideStraight
Designed to combine the fast freecutting of O flute geometry with thetool life available from solid carbideparticularly in small diameters.
■ Usage Natural wood and aluminum
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
61-090 9⁄32 3⁄4 3⁄8 21⁄2
61-100 5⁄16 13⁄16 3⁄8 21⁄2
61-120 3⁄8 7⁄8 3⁄8 21⁄2
61-140 7⁄16 1 1⁄2 3
61-160 1⁄2 1 1⁄2 3
PART # CED CEL SHK DIA OAL
61-040 1⁄8 1⁄2 1⁄4 2
61-050 5⁄32 9⁄16 1⁄4 2
61-060 3⁄16 5⁄8 1⁄4 2
61-070 7⁄32 5⁄8 1⁄4 21⁄2
61-080 1⁄4 3⁄4 1⁄4 21⁄2
ASW
Page 96
61-000P Single Edge - Solid CarbideStraight
Designed to combine the fast freecutting of O flute geometry with thetool life available from solid carbideparticularly in small diameters.
■ Usage Polycarbonate, polyethylene,polypropylene, polystyrene, PVC,extruded acrylic, HDPE, UHMW andhard plastic
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
61-081 1⁄4 3⁄8 1⁄4 21⁄2
61-082 1⁄4 3⁄4 1⁄4 21⁄2
61-082L 1⁄4 3⁄4 1⁄4 21⁄2
61-083* 1⁄4 3⁄4 1⁄4 31⁄4
61-083L* 1⁄4 3⁄4 1⁄4 31⁄4
61-085* 1⁄4 1 1⁄4 31⁄4
61-084* 1⁄4 11⁄4 1⁄4 4
61-121 3⁄8 5⁄8 3⁄8 21⁄2
61-122 3⁄8 7⁄8 3⁄8 21⁄2
61-123* 3⁄8 15⁄8 3⁄8 6
61-162 1⁄2 1 1⁄2 3
61-164 1⁄2 15⁄8 1⁄2 4
61-166 1⁄2 21⁄8 1⁄2 6
PART # CED CEL SHK DIA OAL
61-041 1⁄8 5⁄16 1⁄4 2
61-044 1⁄8 1⁄2 1⁄8 2
61-042 1⁄8 1⁄2 1⁄4 2
61-042L 1⁄8 1⁄2 1⁄4 2
61-045 1⁄8 5⁄8 1⁄8 3
61-043 1⁄8 5⁄8 1⁄4 4
61-052 5⁄32 9⁄16 1⁄4 2
61-061 3⁄16 3⁄8 1⁄4 2
61-064 3⁄16 5⁄8 3⁄16 21⁄2
61-062 3⁄16 5⁄8 1⁄4 2
61-062L 3⁄16 5⁄8 1⁄4 2
61-063* 3⁄16 1 1⁄4 4
61-072 7⁄32 5⁄8 1⁄4 21⁄2
* These tools are designed and toleranced for air routers with guide bushings.L= left hand rotation
SP HP
PART # CED CEL SHK DIA OAL
61-285 1⁄4 1 1⁄4 21⁄2
61-320 3⁄8 11⁄8 3⁄8 3
PART # CED CEL SHK DIA OAL
61-240 1⁄8 1⁄2 1⁄4 2
61-260 3⁄16 3⁄4 1⁄4 2
61-280 1⁄4 7⁄8 1⁄4 21⁄2
61-200 Single Edge - Solid CarbideStraight Wood Rout
Designed to enhance operationswhere the benefits of spiral actionare not needed. The single edge provides fast, free cutting with optimum cutter life.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
Page 97Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
SP HP
PART # CED CEL SHK DIA OAL
61-414 8 mm 25 mm 8 mm 64 mm
61-418 12 mm 35 mm 12 mm 88 mm
PART # CED CEL SHK DIA OAL
61-410 4 mm 16 mm 6 mm 64 mm
61-411 5 mm 20 mm 6 mm 64 mm
61-412 6 mm 25 mm 6 mm 64 mm
61-400 Single Edge - Solid CarbideStraight
Designed to combine the fast free cutting of O flute geometry with thetool life available from solid carbideparticularly in small diameters.
■ Usage Polycarbonate, polyethylene,polypropylene, polystyrene, PVC,extruded acrylic, HDPE, UHMW and hard plastic
■ Material See Selection Guide - pg. 2 - 12
METRICMETRIC
PART # CED CEL SHK DIA OAL
62-100 5⁄16 13⁄16 3⁄8 21⁄2
PART # CED CEL SHK DIA OAL
62-040 1⁄8 1⁄2 1⁄4 2
62-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
62-000 Single Edge - Solid CarbideDowncut Spiral
Good general purpose tools that hold up well in abrasive plastics and aluminum where downward chip flow is preferred.
■ Usage Fiberglass, phenolic and aluminum
■ Material See Selection Guide - pg. 2 - 12HWCP A
PART # CED CEL SHK DIA OAL
62-320 3⁄8 11⁄8 3⁄8 3
62-360 1⁄2 11⁄8 1⁄2 3
PART # CED CEL SHK DIA OAL
62-240 1⁄8 1⁄2 1⁄4 2
62-280 1⁄4 5⁄8 1⁄4 21⁄2
62-285 1⁄4 1 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
62-200 Single Edge - Solid CarbideDowncut Spiral Wood Rout
Designed for routing wood and wood composites where aggressive downward chip removal is necessary in hand-fed or CNC applications.Tool rigidity, long life, and high qualityfinish are also characteristic ofthese tools.
■ Usage Natural wood and wood composites
■ Material See Selection Guide - pg. 2 - 12SW CWHW
Page 98
62-600 Single Edge - Solid CarbideDowncut Spiral O Flute
High speed cutters for machiningaluminum sheet material. These toolsare optimized for use on high-speedCNC mills, high speed machiningcenters and CNC routers.
■ Usage Aluminum, plate, single & multi sheet
■ Material See Selection Guide - pg. 2 - 12A
PART # CED CEL SHK DIA OAL
62-602 1⁄16 1⁄4 1⁄8 11⁄2
62-604 1⁄8 1⁄4 1⁄8 11⁄2
62-606 1⁄8 1⁄4 1⁄4 2
62-610 1⁄8 1⁄2 1⁄4 2
62-612 3⁄16 3⁄8 3⁄16 11⁄2
62-614 3⁄16 3⁄8 1⁄4 2
62-618 3⁄16 5⁄8 1⁄4 2
HELIX ANGLE ≈ 22°
PART # CED CEL SHK DIA OAL
62-620 1⁄4 3⁄8 1⁄4 2
62-622 1⁄4 3⁄4 1⁄4 21⁄2
62-624 1⁄4 11⁄4 1⁄4 3
62-630 5⁄16 3⁄4 1⁄2 3
62-625 3⁄8 3⁄4 3⁄8 3
62-626 3⁄8 11⁄8 3⁄8 3
62-631 1⁄2 11⁄8 1⁄2 31⁄2
62-700 Single Edge - Solid Carbide62-750 Downcut Spiral O Flute62-80062-850
(HP) Designed to provide a smoothfinish in hard plastics with downwardchip removal.(SP) Designed to provide providea smooth finish in soft plastic withdownward chip removal.
■ Usage (HP): Acrylic, nylon, PVC, polycarbonateand solid surface(SP): HDPE, HIPS, UHMW, ABS,polycarbonate, PE, polystyrene,polypropylene, acetal, acrylic, PETand solid surface
■ Material 62-700 62-750
62-800 62-850See Selection Guide - pg. 2 - 12
HP SSP SP HP SSP
HP SSP SP HP SSP
PART # PART # CED CEL SHK DIA OAL
62-828 62-878 5mm 16mm 5mm 64 mm
62-830 62-880 5mm 16mm 6mm 64mm
62-832 62-882 5mm 30mm 5mm 64mm
62-834 62-884 6mm 8mm 6mm 64mm
62-836 62-886 6mm 12mm 6mm 64mm
62-838 62-888 6mm 20mm 6mm 64mm
62-840 62-890 6mm 30mm 6mm 76mm
62-842 62-892 6mm 38mm 6mm 76mm
62-844 62-894 8mm 25mm 8mm 64mm
62-846 62-896 8mm 38mm 8mm 76mm
62-848 62-898 10mm 30mm 10mm 76mm
62-849 62-899 10mm 35mm 10mm 76mm
62-847 62-897 12mm 38mm 12mm 76mm
PART # PART # CED CEL SHK DIA OAL
62-802 62-852 2mm 8mm 2mm 50mm
62-804 62-854 2mm 8mm 6mm 64mm
62-806 62-856 2.5mm 8mm 2.5mm 50mm
62-808 62-858 2.5mm 8mm 6mm 64mm
62-810 62-860 3mm 8mm 3mm 50mm
62-812 62-862 3mm 8mm 6mm 64mm
62-814 62-864 3mm 12mm 3mm 64mm
62-816 62-866 3mm 12mm 6mm 64mm
62-818 62-868 4mm 8mm 4mm 64mm
62-820 62-870 4mm 12mm 4mm 64mm
62-822 62-872 4mm 20mm 4mm 64mm
62-824 62-874 4mm 20mm 6mm 64mm
62-826 62-876 4mm 30mm 4mm 64mm
HELIX ANGLE ≈ 21°
METRIC
PART # PART # CED CEL SHK DIA OAL
62-725 62-775 1⁄4 3⁄4 1⁄4 21⁄2
62-726 62-776 1⁄4 11⁄4 1⁄4 3
62-727 1⁄4 11⁄2 1⁄4 3
62-733 62-783 3⁄8 11⁄8 3⁄8 33⁄8 15⁄8 3⁄8 31⁄2
62-740 62-790 1⁄2 15⁄8 1⁄2 31⁄2
PART # PART # CED CEL SHK DIA OAL
62-713 62-763 1⁄8 1⁄2 1⁄8 2
62-712 62-762 1⁄8 1⁄2 1⁄4 2
62-715 5⁄32 9⁄16 1⁄4 2
62-719 62-769 3⁄16 5⁄8 3⁄16 2
62-718 62-768 3⁄16 5⁄8 1⁄4 27⁄32 3⁄4 1⁄4 21⁄2
HARD PLASTIC
SOFTPLASTIC
HARD PLASTIC
SOFTPLASTIC
Page 99Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
62-900 Single Edge - Solid CarbideDowncut Spiral O Flute
High speed cutters for machiningaluminum sheet material. These toolsare optimized for use on high-speedCNC mills, high speed machiningcenters and CNC routers.
■ Usage Aluminum, plate, single & multi sheet
■ Material See Selection Guide - pg. 2 - 12A
PART # CED CEL SHK DIA OAL
62-902 2mm 6mm 2mm 50mm
62-904 2mm 6mm 6mm 64mm
62-906 2.5mm 6mm 2.5mm 50mm
62-908 2.5mm 6mm 6mm 64mm
62-910 3mm 8mm 3mm 50mm
62-912 3mm 8mm 6mm 64mm
62-914 3mm 12mm 3mm 64mm
62-916 3mm 12mm 6mm 64mm
62-918 4mm 8mm 4mm 64mm
62-920 4mm 12mm 4mm 64mm
62-922 4mm 20mm 4mm 64mm
62-924 4mm 20mm 6mm 64mm
62-926 4mm 30mm 4mm 64mm
HELIX ANGLE ≈ 22°
METRIC
PART # CED CEL SHK DIA OAL
62-928 5mm 16mm 5mm 64mm
62-930 5mm 16mm 6mm 64mm
62-932 5mm 30mm 5mm 64mm
62-934 6mm 8mm 6mm 64mm
62-936 6mm 12mm 6mm 64mm
62-938 6mm 20mm 6mm 64mm
62-940 6mm 30mm 6mm 76mm
62-942 6mm 38mm 6mm 76mm
62-944 8mm 25mm 8mm 64mm
62-946 8mm 38mm 8mm 76mm
62-948 10mm 30mm 10mm 76mm
62-950 12mm 38mm 12mm 76mm
METRIC
PART # CED CEL SHK DIA OAL
63-090 9⁄323⁄4 3⁄8 21⁄2
63-100 5⁄1613⁄16
3⁄8 21⁄2
63-120 3⁄8 7⁄8 3⁄8 21⁄2
63-160 1⁄2 1 1⁄2 3
PART # CED CEL SHK DIA OAL
63-040 1⁄8 1⁄2 1⁄4 2
63-050 5⁄329⁄16 1⁄4 2
63-060 3⁄165⁄8 1⁄4 2
63-080 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
63-000 Single Edge - Solid CarbideUpcut Spiral
Designed for routing where upwardchip removal, tool rigidity, long life, andhigh quality finish is desired.
■ Usage Fiberglass, phenolic and aluminum
■ Material See Selection Guide - pg. 2 - 12HWCP A
SW HW CW
PART # CED CEL SHK DIA OAL
63-300 5⁄16 11⁄8 5⁄16 3
63-320 3⁄8 11⁄8 3⁄8 3
63-360 1⁄2 11⁄8 1⁄2 3
PART # CED CEL SHK DIA OAL
63-240 1⁄8 1⁄2 1⁄4 2
63-260 3⁄16 3⁄4 1⁄4 2
63-280 1⁄4 7⁄8 1⁄4 21⁄2
63-285 1⁄4 1 1⁄4 21⁄2
HELIX ANGLE ≈ 30°
63-200 Single Edge - Solid CarbideUpcut Spiral Wood Rout
Designed for routing where aggressiveupward chip removal is necessary inhand-fed or CNC applications.Tool rigidity, long life, and high qualityfinish are characteristic of these tools.
■ Usage Natural wood andwood composites
■ Material See Selection Guide - pg. 2 - 12
Page 100
63-600 Single Edge - Solid CarbideUpcut Spiral O Flute
High speed cutters for machiningaluminum sheet and block material.These tools are optimized for use onhigh-speed CNC mills, high speedmachining centers and CNC routers.
■ Usage Aluminum plate and single/multi sheetaluminum
■ Material See Selection Guide - pg. 2 - 12A
PART # CED CEL SHK DIA OAL
63-602 1⁄16 1⁄4 1⁄8 11⁄2
63-603 3⁄32 1⁄4 1⁄8 2
63-604 1⁄8 1⁄4 1⁄8 11⁄2
63-606 1⁄8 1⁄4 1⁄4 2
63-610 1⁄8 1⁄2 1⁄4 2
63-611 5⁄32 5⁄16 3⁄16 2
63-612 3⁄16 3⁄8 3⁄16 11⁄2
63-614 3⁄16 3⁄8 1⁄4 2
63-618 3⁄16 5⁄8 1⁄4 2
63-619 7⁄32 7⁄16 1⁄4 21⁄2
63-620 1⁄4 3⁄8 1⁄4 2
63-622 1⁄4 3⁄4 1⁄4 21⁄2
HELIX ANGLE ≈ 22°
PART # CED CEL SHK DIA OAL
63-624 1⁄4 11⁄4 1⁄4 3
63-628 9⁄32 7⁄16 5⁄16 21⁄2
63-629 5⁄16 9⁄16 5⁄16 21⁄2
63-630 5⁄16 3⁄4 1⁄2 3
63-634 21⁄64 3⁄4 1⁄2 3
63-637 11⁄32 9⁄16 3⁄8 21⁄2
63-625 3⁄8 3⁄4 3⁄8 3
63-626 3⁄8 11⁄8 3⁄8 3
63-627 3⁄8 13⁄8 3⁄8 31⁄2
63-631 1⁄2 11⁄8 1⁄2 31⁄2
63-632 1⁄2 13⁄8 1⁄2 31⁄2
Page 101Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
63-700 Single Edge - Solid Carbide63-750 Upcut Spiral O Flute63-80063-850
(HP) Designed to provide a smoothfinish in hard plastics with upwardchip removal.(SP) Designed to provide providea smooth finish in soft plastic withupward chip removal.
■ Usage (HP): Acrylic, nylon, PVC, polycarbonateand solid surface(SP): HDPE, HIPS, UHMW, ABS,polycarbonate, PE, polystyrene,polypropylene, acetal, acrylic, PETand solid surface
■ Material 63-700
63-750
63-800
63-850 See Selection Guide - pg. 2 - 12
HP SSP
PART # PART # CED CEL SHK DIA OAL
63-802 63-852 2mm 8mm 2mm 50mm
63-804 63-854 2mm 8mm 6mm 64mm
63-806 63-856 2.5 mm 8mm 2.5mm 50mm
63-808 63-858 2.5 mm 8mm 6mm 64mm
63-810 63-860 3mm 8mm 3mm 50mm
63-812 63-862 3mm 8mm 6mm 64mm
63-814 63-864 3mm 12mm 3mm 64mm
63-816 63-866 3mm 12mm 6mm 64mm
63-818 63-868 4mm 8mm 4mm 64mm
63-820 63-870 4mm 12mm 4mm 64mm
63-822 63-872 4mm 20mm 4mm 64mm
63-824 63-874 4mm 20mm 6mm 64mm
63-826 63-876 4mm 30mm 4mm 64mm
HELIX ANGLE ≈ 21°
PART # PART # CED CEL SHK DIA OAL
63-701 63-751 1⁄16 1⁄4 1⁄8 2
63-700 63-750 1⁄16 1⁄4 1⁄4 2
63-711 63-761 1⁄8 1⁄4 1⁄8 2
63-710 63-760 1⁄8 1⁄4 1⁄4 2
63-713 63-763 1⁄8 1⁄2 1⁄8 2
63-712 63-762 1⁄8 1⁄2 1⁄4 2
63-743* 63-793* 1⁄8 1⁄2 1⁄4 2
63-715 5⁄32 9⁄16 1⁄4 2
63-716 63-766 3⁄163⁄8 3⁄16 2
63-717 63-767 3⁄16 3⁄8 1⁄4 2
63-719 63-769 3⁄16 5⁄8 3⁄16 2
63-718 63-768 3⁄16 5⁄8 1⁄4 2
HELIX ANGLE ≈ 21° * Special Point for Improved Bottom Finish
METRIC METRIC
PART # PART # CED CEL SHK DIA OAL
63-720 7⁄32 3⁄4 1⁄4 21⁄2
63-724 63-774 1⁄4 3⁄8 1⁄4 2
63-744* 63-794* 1⁄4 3⁄4 1⁄4 21⁄2
63-725 63-775 1⁄4 3⁄4 1⁄4 21⁄2
63-726 63-776 1⁄4 11⁄4 1⁄4 3
63-727 63-777 1⁄4 11⁄2 1⁄4 3
63-730 63-780 3⁄8 5⁄8 3⁄8 21⁄2
63-731 63-781 3⁄8 3⁄4 3⁄8 3
63-733 63-783 3⁄8 11⁄8 3⁄8 3
63-735 63-785 3⁄8 15⁄8 3⁄8 31⁄2
63-745* 63-795* 3⁄8 15⁄8 3⁄8 31⁄2
63-740 63-790 1⁄2 15⁄8 1⁄2 31⁄2
63-746* 63-796* 1⁄2 15⁄8 1⁄2 31⁄2
HARD PLASTIC
SOFTPLASTIC
HARD PLASTIC
SOFTPLASTIC
HARD PLASTIC
SOFTPLASTIC
HARD PLASTIC
SOFTPLASTIC
PART # PART # CED CEL SHK DIA OAL
63-828 63-878 5mm 16mm 5mm 64mm
63-830 63-880 5mm 16mm 6mm 64mm
63-832 63-882 5mm 30mm 5mm 64mm
63-834 63-884 6mm 8mm 6mm 64mm
63-836 63-886 6mm 12mm 6mm 64mm
63-838 63-888 6mm 20mm 6mm 64mm
63-840 63-890 6mm 30mm 6mm 76mm
63-842 63-892 6mm 38mm 6mm 76mm
63-844 63-894 8mm 25mm 8mm 64mm
63-846 63-896 8mm 38mm 8mm 76mm
63-848 63-898 10mm 30mm 10mm 76mm
63-849 63-899 10mm 35mm 10mm 76mm
63-847 63-897 12mm 38mm 12mm 76mm
SP HP SSP
HP SSP
SP HP SSP
Page 102
■ Usage Plastic, wood, aluminum and solid surface
■ Material
63-900 Single Edge - Solid CarbideUpcut Spiral O Flute
High speed cutters for machiningaluminum sheet and block material.These tools are optimized for use onhigh-speed CNC mills, high speedmachining centers and CNC routers.
■ Usage Aluminum plate and single/multi sheetaluminum
■ Material See Selection Guide - pg. 2 - 12A
A
PART # CED CEL SHK DIA OAL
63-902 2mm 6mm 2mm 50mm
63-904 2mm 6mm 6mm 64mm
63-906 2.5mm 6mm 2.5mm 50mm
63-908 2.5mm 6mm 6mm 64mm
63-910 3mm 8mm 3mm 50mm
63-912 3mm 8mm 6mm 64mm
63-914 3mm 12mm 3mm 64mm
63-916 3mm 12mm 6mm 64mm
63-918 4mm 8mm 4mm 64mm
63-920 4mm 12mm 4mm 64mm
63-922 4mm 20mm 4mm 64mm
63-924 4mm 20mm 6mm 64mm
63-926 4mm 30mm 4mm 64mm
HELIX ANGLE ≈ 22°
METRIC
PART # CED CEL SHK DIA OAL
63-928 5mm 16mm 5mm 64mm
63-930 5mm 16mm 6mm 64mm
63-932 5mm 30mm 5mm 64mm
63-934 6mm 8mm 6mm 64mm
63-936 6mm 12mm 6mm 64mm
63-938 6mm 20mm 6mm 64mm
63-940 6mm 30mm 6mm 76mm
63-942 6mm 38mm 6mm 76mm
63-944 8mm 25mm 8mm 64mm
63-946 8mm 38mm 8mm 76mm
63-948 10mm 30mm 10mm 76mm
63-950 12mm 38mm 12mm 76mm
METRIC
PART # CED CEL SHK DIA OAL
64-025 1⁄4 3⁄4 1⁄4 2
64-026 1⁄4 11⁄4 1⁄4 3
64-031 3⁄8 3⁄4 3⁄8 3
64-033 3⁄8 11⁄8 3⁄8 3
64-000 Single Edge - Solid CarbideDowncut Spiral O Flute
The polished flute allows for razor sharpcutting edge and easy chip evacuation.The tool is available in a down cut spiralfor improved part holding.
PART # CED CEL SHK DIA OAL
64-000 1⁄16 1⁄4 1⁄8 2
64-012 1⁄8 1⁄2 1⁄4 2
64-016 3⁄16 3⁄8 3⁄16 2
64-018 3⁄16 5⁄8 1⁄4 2
64-024 1⁄4 3⁄8 1⁄4 2
HELIX ANGLE ≈ 21°
PART # CED CEL SHK DIA OAL
65-020 3⁄16 11⁄4 1⁄4 3
65-023 1⁄4 5⁄8 1⁄4 2
65-025 1⁄4 7⁄8 1⁄4 21⁄2
65-026 1⁄4 11⁄4 1⁄4 3
65-027 1⁄4 11⁄2 1⁄4 3
65-033 3⁄8 11⁄8 3⁄8 3
65-000 Single Edge - Solid CarbideUpcut Spiral O Flute
The polished flute allows for razor sharpcutting edge and easy chip evacuation.The tool is available in a upcut spiral forimproved part holding.
■ Usage Plastic, wood, aluminum and solid surface
■ Material
PART # CED CEL SHK DIA OAL
65-000 1⁄16 1⁄4 1⁄8 2
65-010 1⁄8 1⁄4 1⁄4 2
65-013 1⁄8 1⁄2 1⁄8 2
65-012 1⁄8 1⁄2 1⁄4 2
65-019 3⁄165⁄8 3⁄16 2
65-018 3⁄165⁄8 1⁄4 2
HELIX ANGLE ≈ 21°
SW HW CW SP HP SSP See SelectionGuide - pg. 2 - 12
ASW HW CW SP HP SSP See SelectionGuide - pg. 2 - 12
Page 103Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Edge rounding of parts
■ Material See Selection Guide - pg. 2 - 12
66-000 Solid Carbide Edge RoundingDesigned for rounding the edge ofsheets or parts. They come in bothsingle edge and double edge.
SP HP SSP
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-120 3⁄8 3⁄8 3⁄8 21⁄2 5⁄32 1⁄8 .320 1⁄16 1⁄8
66-121 3⁄8 3⁄8 3⁄8 21⁄2 7⁄32 3⁄16 .305 1⁄16 3⁄16
66-122 3⁄8 3⁄8 3⁄8 21⁄2 9⁄32 1⁄4 .288 1⁄16 1⁄4
66-123 3⁄8 1⁄2 3⁄8 21⁄2 13⁄32 3⁄8 .255 1⁄16 3⁄8
66-160 1⁄2 3⁄8 1⁄2 3 5⁄32 1⁄8 .445 1⁄16 1⁄8
66-161 1⁄2 3⁄8 1⁄2 3 7⁄32 3⁄16 .430 1⁄16 3⁄16
66-162 1⁄2 3⁄8 1⁄2 3 9⁄32 1⁄4 .413 1⁄16 1⁄4
66-163 1⁄2 5⁄8 1⁄2 3 17⁄32 1⁄2 .347 1⁄16 1⁄2
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-082 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄8
66-083 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16
66-084 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4
SINGLE EDGE STRAIGHT 0-FLUTE
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-085 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄8
66-086 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16
66-087 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4
HELIX ANGLE ≈ 22°
SINGLE EDGE SPIRAL 0-FLUTE
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-092 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄8
66-093 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16
66-094 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4
DOUBLE EDGE STRAIGHT 0-FLUTE
DOUBLE EDGE STRAIGHT V-FLUTE
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-073 6mm 10mm 6mm 64mm 4mm 3mm 4.47mm 1.5mm 3mm
66-074 6mm 10mm 6mm 64mm 5mm 4mm 4.24mm 1.5mm 4mm
66-075 6mm 10mm 6mm 64mm 6mm 5mm 3.96mm 1.5mm 5mm
66-076 6mm 10mm 6mm 64mm 7mm 6mm 3.73mm 1.5mm 6mm
DOUBLE EDGE STRAIGHT 0-FLUTE METRIC
PART # CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE
66-077 8mm 12mm 8mm 64mm 9mm 8mm 5.21mm 1.5mm 8mm
66-078 10mm 14mm 10mm 70mm 11mm 10mm 6.68mm 1.5mm 10mm
66-079 12mm 16mm 12mm 76mm 13mm 12mm 8.18mm 1.5mm 12mm
DOUBLE EDGE STRAIGHT V-FLUTE METRIC
Opening
Tip toRadius
CED
CEL
Page 104
66-200 Double Edge - Solid CarbideRout and Chamfer
Designed to provide up to a 1/16” topface chamfer and a finished side edgeon plastic sheets or parts.
■ Usage Rout and chamfer in plastic
■ Material See Selection Guide - pg. 2 - 12SP HP
PART # CED CEL SHK DIA OAL MAT’L THICKNESS
66-200 1⁄4 3⁄16 3⁄8 21⁄4 1⁄8
66-204 1⁄4 1⁄4 3⁄8 21⁄4 3⁄16
HELIX ANGLE ≈ 0°
PART # CED CEL SHK DIA OAL MAT’L THICKNESS
66-210 3⁄8 5⁄16 1⁄2 3 1⁄4
66-300 Double Edge - Solid Carbide66-350 Upcut Bottom Surfacing
Designed for pocketing applicationswhere the bottom of the pocket mustbe smooth.
■ Usage Bottom surfacing for plastic and aluminum
■ Material See Selection Guide - pg. 2 - 12SP HP
PART # CED CORNER RADIUS CEL SHK DIA OAL
66-308 1⁄8 .020 1⁄4 1⁄4 2
66-309 1⁄8 .002 1⁄4 1⁄4 2
66-314 1⁄4 .030 3⁄8 1⁄4 2
66-315 1⁄4 .002 3⁄8 1⁄4 2
66-320 3⁄8 .030 5⁄8 3⁄8 21⁄2
66-321 3⁄8 .002 5⁄8 3⁄8 21⁄2
66-326 1⁄2 .030 7⁄8 1⁄2 3
66-327 1⁄2 .002 7⁄8 1⁄2 3
66-328 3⁄4 .040 11⁄8 3⁄4 4
HELIX ANGLE ≈ 30°
PART # CED CORNER RAD CEL SHK DIA OAL
66-356 3mm 1mm 6mm 3mm 40mm
66-358 3mm 1mm 6mm 6mm 51mm
66-364 6mm 1.25mm 10mm 6mm 51mm
66-370 8mm 1.25mm 12mm 8mm 64mm
66-376 12mm 1.25mm 20mm 12mm 76mm
HELIX ANGLE ≈ 30°
METRIC
Page 105Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
67-000 Solid Carbide67-250 Fiberglass Router
Designed as fiberglass routers.Their upcut/downcut diamond designeffectively shears fibrous materials.Certain tools in the line have beenfurther developed to cut aramidfiber composites.
■ Usage Fiberglass and phenolic
■ Material See Selection Guide - pg. 2 - 12
MEDIUM BURR W/PLUNGE POINT
DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-080 1⁄4 3⁄4 1⁄4 21⁄2 67-080DFC
67-120 3⁄8 7⁄8 3⁄8 21⁄2 67-120DFC
67-160 1⁄2 1 1⁄2 3 67-160DFC
METRIC DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-090 4mm 16mm 6mm 50mm 67-090DFC
67-091 6mm 19mm 6mm 63mm 67-091DFC
67-092 6mm 25mm 6mm 75mm 67-092DFC
67-093 8mm 25mm 8mm 63mm 67-093DFC
67-094 10mm 25mm 10mm 75mm 67-094DFC
67-095 12mm 25mm 12mm 75mm 67-095DFC
MEDIUM BURR W/END MILL POINT
DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-003 1⁄8 1 1⁄8 2 67-003DFC
67-010 1⁄4 3⁄4 1⁄4 21⁄2 67-010DFC
67-011 1⁄4 11⁄8 1⁄4 3 67-011DFC
67-012 1⁄4 11⁄4 1⁄4 3 67-012DFC
67-014 1⁄4 11⁄2 1⁄4 3 67-014DFC
67-017 1⁄4 21⁄8 1⁄4 4 67-017DFC
67-030 3⁄8 7⁄8 3⁄8 21⁄2 67-030DFC
MEDIUM BURR W/END MILL POINT
DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-023 3⁄8 15⁄8 3⁄8 3 67-023DFC
67-027 3⁄8 21⁄8 3⁄8 4 67-027DFC
67-031 1⁄2 11⁄8 1⁄2 3 67-031DFC
67-033 1⁄2 15⁄8 1⁄2 4 67-033DFC
67-037 1⁄2 21⁄8 1⁄2 4 67-037DFC
67-039 1⁄2 31⁄8 1⁄2 5 -
67-065 3⁄4 41⁄8 3⁄4 6 -
3/E DOWNCUT DIAMOND GRIT TOOL
PART # CED CEL SHK OALDIA
67-256 1⁄4 13⁄8 1⁄4 3
67-258 3⁄8 13⁄8 3⁄8 3
PART # CED CEL SHK OALDIA
67-254 1⁄4 11⁄8 1⁄4 3
ARAMID TOOL
PART # CED CEL SHK OALDIA
67-084 1⁄4 3⁄4 1⁄4 21⁄2
67-124 3⁄8 7⁄8 3⁄8 21⁄2
ARAMID TOOL
PART # CED CEL SHK OALDIA
67-164 1⁄2 1 1⁄2 3
2 FLUTE BURR
DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-082 1⁄4 3⁄4 1⁄4 21⁄2 67-082DFC
67-122 3⁄8 7⁄8 3⁄8 21⁄2 67-122DFC
2 FLUTE BURR
DIAMONDPART # CED CEL SHK OAL COATEDDIA PART #
67-162 1⁄2 1 1⁄2 3 67-162DFC
3/E DOWNCUT DIAMOND GRIT TOOL
MEDIUM BURR w/PLUNGEPOINT
CP
Page 106
■ Usage Composite panels and honeycomb core
■ Material See Selection Guide - pg. 2 - 12
UPCUT DOWNCUT
CP
CP
67-300 Double Edge - Solid CarbideCompression Spiral
Compression design for fast feedand excellent finish on both sidesof the material.
PART # CED CEL SHK DIA OAL DIAMOND COATED #
67-305 1⁄4 7⁄8 1⁄4 21⁄2 -
67-314 3⁄8 11⁄8 3⁄8 3 67-314DFC
* = Mortise Compression HELIX ANGLE ≈ 30°
PART # CED CEL SHK DIA OAL DIAMOND COATED #
67-320* 1⁄2 7⁄8 1⁄2 3 -
67-322 1⁄2 11⁄8 1⁄2 3 67-322DFC
67-400 Solid Carbide Un-Ruffer™PATENTED
The unique design allows for thecutting performance of a burr whileachieving a good surface finish.
■ Usage Composite panels
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
67-410 1⁄8 1⁄2 1⁄8 11⁄2
67-423 1⁄4 3⁄4 1⁄4 2
67-426 1⁄4 1 1⁄4 21⁄2
Tools can be diamond coated upon request
PART # CED CEL SHK DIA OAL
67-428 1⁄4 1 1⁄4 3
67-435 3⁄8 1 3⁄8 3
67-445 1⁄2 1 1⁄2 3
■ Usage Phenolic
■ Material See Selection Guide - pg. 2 - 12
67-200 Three Edge - Solid CarbidePhenolic Cutter
CP
Equally adaptable to low or high spindle speed applications in any CNC machining environment. The freecutting action of the tools provides forbetter finishes and significantly lowernoise levels.
PART # CED CEL SHK DIA OAL
67-205 3⁄8 7⁄8 3⁄8 3
67-211 1⁄2 11⁄8 1⁄2 3
67-215 1⁄2 21⁄8 1⁄2 4
HELIX ANGLE ≈ 10°
PART # CED CEL SHK DIA OAL
67-206 3⁄8 7⁄8 3⁄8 3
67-212 1⁄2 11⁄8 1⁄2 31⁄2
67-216 1⁄2 21⁄8 1⁄2 41⁄2
Page 107Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Carbon graphite andcarbon fiber panels
■ Material See Selection Guide - pg. 2 - 12
67-500 Solid CarbideCG Tool (Carbon Graphite)
CP
The geometry of these tools increasesthe amount of effective cutting flutesresulting in superior performance overa standard burr.
PART # CED CEL SHK DIA OAL
67-505 1⁄8 1⁄2 1⁄8 2
67-508 3⁄16 5⁄8 3⁄16 2
67-511 1⁄4 3⁄4 1⁄4 3
67-514 1⁄4 11⁄2 1⁄4 3
PART # CED CEL SHK DIA OAL
67-520 3⁄8 11⁄8 3⁄8 3
67-523 1⁄2 11⁄8 1⁄2 31⁄2
67-526 1⁄2 21⁄8 1⁄2 4
■ Usage Carbon graphite,aramid, composite sheets
■ Material See Selection Guide - pg. 2 - 12
67-600 Solid CarbideFMR (Fiber Metal Router)
CP
Similar to the CG Tool, but theenhanced tooth design allows the toolto cut fiber metals and other abrasivematerials quickly and easily. The spe-cial clean out flutes allows the materialto be quickly removed from the cuttingarea improving the surface finish.
PART # CED CEL SHK DIA OAL
67-605 1⁄8 1⁄2 1⁄8 2
67-608 3⁄16 5⁄8 3⁄16 2
67-611 1⁄4 3⁄4 1⁄4 3
67-614 1⁄4 11⁄2 1⁄4 3
PART # CED CEL SHK DIA OAL
67-620 3⁄8 11⁄8 3⁄8 3
67-623 1⁄2 11⁄8 1⁄2 31⁄2
67-626 1⁄2 21⁄8 1⁄2 4
Page 108
PART# CED CEL SHK OALDIA
67-807 1⁄8 (0.125) 11⁄4 0.125 21⁄4
67-808 9⁄64 (0.140) 13⁄8 0.140 21⁄2
67-809 5⁄32 (0.156) 13⁄8 0.156 21⁄2
67-810 11⁄64 (0.172) 15⁄8 0.172 23⁄4
67-811 3⁄16 (0.188) 15⁄8 0.188 23⁄4
67-812 13⁄64 (0.203) 13⁄4 0.203 3
67-813 7⁄32 (0.219) 13⁄4 0.219 3
67-814 15⁄64 (0.234) 2 0.234 31⁄4
67-815 1⁄4 (0.250) 2 0.250 31⁄4
67-816 17⁄64 (0.266) 21⁄8 0.266 31⁄2
67-817 9⁄32 (0.281) 21⁄8 0.281 31⁄2
67-818 19⁄64 (0.297) 23⁄8 0.297 33⁄4
67-819 5⁄16 (0.313) 23⁄8 0.313 33⁄4
67-820 21⁄64 (0.328) 21⁄2 0.328 4
67-821 11⁄32 (0.344) 21⁄2 0.344 4
67-822 23⁄64 (0.359) 21⁄2 0.359 4
67-823 3⁄8 (0.375) 23⁄4 0.375 41⁄4
67-824 25⁄64 (0.391) 27⁄8 0.391 41⁄2
67-825 13⁄32 (0.406) 27⁄8 0.406 41⁄2
67-826 27⁄64 (0.422) 27⁄8 0.422 41⁄2
67-827 7⁄16 (0.438) 27⁄8 0.438 41⁄2
67-828 29⁄64 (0.453) 3 0.453 43⁄4
67-829 15⁄32 (0.469) 3 0.469 43⁄4
67-830 31⁄64 (0.484) 3 0.484 43⁄4
67-831 1⁄2 (0.500) 3 0.500 43⁄4
67-800 Solid Carbide 8 Facet DrillNEW
Designed to reduce cutting forces andeliminating delamination when exitingthe material.
■ Usage Carbon fiber and other composite material
■ Material See Selection Guide - pg. 2 - 12
FRACTIONAL DRILLS
PART# CED CEL SHK OALDIA
67-859 J (0.277) 21⁄8 0.277 31⁄2
67-860 K (0.281) 21⁄8 0.281 31⁄2
67-861 L (0.291) 21⁄8 0.291 31⁄2
67-862 M (0.295) 23⁄8 0.295 33⁄4
67-863 N (0.302) 23⁄8 0.302 33⁄4
67-864 O (0.316) 23⁄8 0.316 33⁄4
67-865 P (0.323) 23⁄8 0.323 33⁄4
67-866 Q (0.332) 21⁄2 0.332 4
67-867 R (0.339) 21⁄2 0.339 4
67-868 S (0.348) 21⁄2 0.348 4
67-869 T (0.358) 21⁄2 0.358 4
67-870 U (0.368) 23⁄4 0.368 41⁄4
67-871 V (0.377) 23⁄4 0.377 41⁄4
67-872 W (0.386) 27⁄8 0.386 41⁄2
67-873 X (0.397) 27⁄8 0.397 41⁄2
67-874 Y (0.404) 27⁄8 0.404 41⁄2
67-875 Z (0.413) 27⁄8 0.413 41⁄2
LETTER DRILLS (CONT.)
PART# CED CEL SHK OALDIA
67-850 A (0.234) 2 0.234 31⁄4
67-851 B (0.238) 2 0.238 31⁄4
67-852 C (0.242) 2 0.242 31⁄4
67-853 D (0.246) 2 0.246 31⁄4
67-854 E (0.250) 2 0.250 31⁄4
67-855 F (0.257) 2 0.257 31⁄4
67-856 G (0.261) 21⁄8 0.261 31⁄2
67-857 H (0.266) 21⁄8 0.266 31⁄2
67-858 I (0.272) 21⁄8 0.272 31⁄2
LETTER DRILLS
PART# CED CEL SHK OALDIA
67-876 1 (0.228) 13⁄4 0.228 3
67-877 2 (0.221) 13⁄4 0.221 3
67-878 3 (0.213) 13⁄4 0.213 3
67-879 4 (0.209) 13⁄4 0.209 3
67-880 5 (0.206) 13⁄4 0.206 3
67-881 6 (0.204) 13⁄4 0.204 3
67-882 7 (0.201) 13⁄4 0.201 3
67-883 8 (0.199) 13⁄4 0.199 3
67-884 9 (0.196) 13⁄4 0.196 3
67-885 10 (0.194) 15⁄8 0.194 23⁄4
67-886 11 (0.191) 15⁄8 0.191 23⁄4
67-887 12 (0.189) 15⁄8 0.189 23⁄4
67-888 13 (0.185) 15⁄8 0.185 23⁄4
67-889 14 (0.182) 15⁄8 0.182 23⁄4
67-890 15 (0.180) 15⁄8 0.180 23⁄4
67-891 16 (0.177) 15⁄8 0.177 23⁄4
67-892 17 (0.173) 15⁄8 0.173 23⁄4
NUMBER DRILLS
PART# CED CEL SHK OALDIA
67-961 3.00 (0.118) 11⁄4 3.00 21⁄4
67-962 3.50 (0.138) 13⁄8 3.50 21⁄2
67-963 4.00 (0.157) 13⁄8 4.00 21⁄2
67-964 4.50 (0.177) 15⁄8 4.50 23⁄4
67-965 5.00 (0.197) 13⁄4 5.00 3
67-966 5.50 (0.217) 13⁄4 5.50 3
67-967 6.00 (0.236) 2 6.00 31⁄4
67-968 6.50 (0.256) 2 6.50 31⁄4
67-969 7.00 (0.276) 21⁄8 7.00 31⁄2
67-970 7.50 (0.295) 23⁄8 7.50 33⁄4
67-971 8.00 (0.315) 23⁄8 8.00 33⁄4
67-972 8.50 (0.335) 21⁄2 8.50 4
67-973 9.00 (0.354) 21⁄2 9.00 4
67-974 9.50 (0.374) 23⁄4 9.50 41⁄4
67-975 10.00 (0.394) 27⁄8 10.00 41⁄2
67-976 10.50 (0.413) 27⁄8 10.50 41⁄2
67-977 11.00 (0.433) 27⁄8 11.00 4 1⁄2
67-978 11.50 (0.453) 3 11.50 43⁄4
67-979 12.00 (0.472) 3 12.00 43⁄4
METRIC DRILLS
PART# CED CEL SHK OALDIA
67-893 18 (0.170) 15⁄8 0.170 23⁄4
67-894 19 (0.166) 15⁄8 0.166 23⁄4
67-895 20 (0.161) 13⁄8 0.161 21⁄2
67-896 21 (0.159) 13⁄8 0.159 21⁄2
67-897 22 (0.157) 13⁄8 0.157 21⁄2
67-898 23 (0.154) 13⁄8 0.154 21⁄2
67-899 24 (0.152) 13⁄8 0.152 21⁄2
67-900 25 (0.150) 13⁄8 0.150 21⁄2
67-901 26 (0.147) 13⁄8 0.147 21⁄2
67-902 27 (0.144) 13⁄8 0.144 21⁄2
67-903 28 (0.141) 13⁄8 0.141 21⁄2
67-904 29 (0.136) 13⁄8 0.136 21⁄2
67-905 30 (0.129) 11⁄4 0.129 21⁄4
67-906 31 (0.120) 11⁄4 0.120 21⁄4
NUMBER DRILLS (CONT.)
CP
X∞
X∞WHAT IS AN 8 FACET DRILL?An 8 facet drill consists of 4 cuttingedges with 2 facets per cuttingedge. These facets consist of thelip relief and the lip clearance angle.
Page 109Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
■ Usage Composite panels and fiberglass
■ Material See Selection Guide - pg. 2 - 12
68-000 Double Edge - PCD TippedTooling
Designed for use in abrasivematerials where cut quality andtool life are important.
PART # CED CEL SHK DIA OAL
68-050 1⁄4 3⁄4 1⁄4 3
68-055 3⁄8 7⁄8 3⁄8 3
68-062 1⁄2 11⁄4 1⁄2 4
68-070 3⁄4 11⁄4 3⁄4 4
68-072 3⁄4 11⁄4 3⁄4 4Down Shear
PART # CED CEL SHK DIA OAL
68-005 1⁄4 3⁄4 1⁄4 3
68-010 3⁄8 3⁄4 3⁄8 3
68-020 1⁄2 3⁄4 1⁄2 4
68-030 3⁄4 1 3⁄4 4
HELIX ANGLE ≈ 0-3°
PCD TIPPED PCD FULL FACE
PCD TIPPED PCD FULL FACE
CP
68-100 Single Edge - PCD Compression ToolNEW
This economical PCD compression toolwill provide long tool life in abrasive woodproducts. The tools have a mortise tipallowing for through cuts and dado’sto be produced using one tool. Thecompression design ensures chip freeedges on the top and bottom.
■ Usage Composite wood
■ Material See Selection Guide - pg. 2 - 12
PART# CED CEL UPCUT SHANK OAL FLUTESCEL
68-104L* 5⁄8 1 0.200 5⁄8 31⁄2 1
68-110 5⁄8 15⁄8 0.200 5⁄8 4 1
68-110L* 5⁄8 15⁄8 0.200 5⁄8 4 1
68-106 3⁄4 1 0.200 3⁄4 4 1
68-106L* 3⁄4 1 0.200 3⁄4 4 1
68-112 3⁄4 15⁄8 0.200 3⁄4 4 1
68-112L* 3⁄4 15⁄8 0.200 3⁄4 4 1
L = Left Hand Rotation* = Tools are not stocked and must be special ordered. Approximately 4 week lead time.
CW
PART# CED CEL UPCUT SHANK OAL FLUTESCEL
68-101 3⁄8 1 0.188 3⁄8 3 1
68-101L 3⁄8 1 0.188 3⁄8 3 1
68-100 3⁄8 1 0.188 1⁄2 3 1
68-100L 3⁄8 1 0.188 1⁄2 3 1
68-102 1⁄2 1 0.200 1⁄2 3 1
68-102L 1⁄2 1 0.200 1⁄2 3 1
68-104 5⁄8 1 0.200 5⁄8 31⁄2 1
68-200 Double Edge - PCD SERF™ CutterNEW
This tool is designed to act like arougher and finishing tool in one. Theunique geometry reduces the cuttingforces resulting in longer tool life,higher feed rates and reduced noise.
■ Usage Composites
■ Material See Selection Guide - pg. 2 - 12CP
PART # CED CEL SHK DIA OAL
68-210 1⁄4 3⁄8 1⁄4 3
68-213 1⁄4 3⁄4 1⁄4 3
68-216 1⁄4 1 1⁄4 31⁄2
68-220 3⁄8 3⁄8 3⁄8 3
68-223 3⁄8 3⁄4 3⁄8 3
PART # CED CEL SHK DIA OAL
68-226 3⁄8 1 3⁄8 31⁄2
68-230 1⁄2 3⁄4 1⁄2 4
68-233 1⁄2 1 1⁄2 4
68-236 1⁄2 11⁄4 1⁄2 4
Page 110
68-900 PCD 8 Facet DrillsNEW The PCD 8 facet drill works well in
composite material where long tool lifeand a delamination free hole is required.The drill diameters are oversize allowingfor aircraft fasteners to extendthrough the holes.
■ Usage Composites
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
68-902 0.100 1 1⁄4 3
68-904 0.129 1 1⁄4 3
68-908 0.147 1 1⁄4 3
68-910 0.192 1 1⁄4 3
PART # CED CEL SHK DIA OAL
68-914 0.251 1 1⁄4 3
68-918 0.313 1 5⁄16 3
68-922 0.376 1 3⁄8 3
68-926 0.502 1 1⁄2 3
CP
70-100 Carbide TippedSaw and Arbor
Designed to trim and groove bothhard and soft plastics. These sawsrun in conjunction with the saw arbors.Saws are reversible for right or lefthand rotation cutting.
■ Usage Hard and soft plastic
■ Material See Selection Guide - pg. 2 - 12
PART # CED TEETH RAKE KERF GRIND
70-100 2 10 0° .095 TCG
70-102 21⁄2 10 0° .095 TCG
70-104 3 10 0° .095 TCG
70-108 4 10 0° .095 TCG
PART # CED TEETH RAKE KERF GRIND
70-120 2 16 0° .095 TCG
70-122 21⁄2 20 0° .095 TCG
70-124 3 20 0° .095 TCG
70-126 31⁄2 20 0° .095 TCG
70-128 4 20 0° .095 TCG
PART # CED TEETH RAKE KERF GRIND
70-160 2 16 -5° .095 TCG
70-162 21⁄2 20 -5° .095 TCG
70-164 3 20 -5° .095 TCG
70-166 31⁄2 20 -5° .095 TCG
70-168 4 20 -5° .095 TCG
TCG = Triple Chip Grind
SOFT PLASTIC - SLOW FEED HARD PLASTIC - FAST FEED
SOFT PLASTIC FAST FEED
PART # SHK DIA OAL
70-180 1⁄2 31⁄4
70-181 1⁄2 41⁄2
*SEE FEED & SPEED CHART ON PAGE 66.
SAW ARBOR - These saw arbors are designed to hold the carbide tipped saws.
SP HP
70-200 Solid CarbideSaw Flush Mount
These small diameter solid carbidearbor mounted saws are designed fortrimming and slotting plastics. Sawsare permanently attached to arborsand are not reversible.
■ Usage Hard and soft plastic
■ Material See Selection Guide - pg. 2 - 12
PART # CED COLLAR SHK DIA KERF OAL ROTATION
70-204 1 9⁄16 1⁄2 .062 4 Right Hand
70-224 11⁄4 5⁄8 1⁄2 .062 4 Right Hand
*SEE FEED & SPEED CHART ON PAGE 66.
SP HP
Page 111Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
70-300 Carbide TippedSaw Flush Mount
Designed for flush trimming andslotting of both hard and soft plastics.Saws are permanently attached toarbors and are not reversible.
■ Usage Hard and soft plastic
■ Material See Selection Guide - pg. 2 - 12
PART # CED TEETH RAKE SHK DIA KERF OAL GRIND ROTATION PLASTIC FEED
70-300 2 10 0° 1⁄2 .095 4 TCG RH Soft Slow
70-302 2 10 0° 1⁄2 .095 4 TCG LH Soft Slow
70-320 2 16 0° 1⁄2 .095 4 TCG RH Soft Fast
70-322 2 16 0° 1⁄2 .095 4 TCG LH Soft Fast
70-340 2 10 -5° 1⁄2 .095 4 TCG RH Hard Slow
70-342 2 10 -5° 1⁄2 .095 4 TCG LH Hard Slow
70-360 2 16 -5° 1⁄2 .095 4 TCG RH Hard Fast
70-362 2 16 -5° 1⁄2 .095 4 TCG LH Hard Fast
*SEE FEED & SPEED CHART BELOW
TCG = Triple Chip Grind
TOOL CED MAX RPM SOFT HARD FIBROUSSERIES PLASTIC PLASTIC REINFRC
70-100 2” 18,000 150 150 150
70-100 21⁄2” 16,000 150 150 150
70-100 3” 14,000 150 150 150
70-100 31⁄2” 12,000 150 150 150
70-100 4” 10,000 150 150 150
70-200 11⁄2” 14,000 150 150 150& Smaller
70-300 2” 16,000 150 150 150
INCHES PER MINUTE
FEEDS & SPEEDS FOR SAWS
SP HP
Page 112
70-400 Carbide Tipped Saws for PlasticNEW
Premium performance design resultsin cool, clean cutting without chippingor melting. Blade design is optimizedfor thick or thin material.
■ Usage Plastic, Composite Plastic
■ Material See Selection Guide - pg. 2 - 12SP
PART # MAT’L THICKNESS DIAMETER KERF PLATE
INCH MM INCH MM TEETH GRIND INCH MM INCH MM ARBOR
70-402 1⁄16 - 3⁄8 2-10 10” 250 60 MATB 0.126 3.2 0.087 2.2 5⁄8
70-404 3⁄8 - 4 10-100 10” 250 20 TCG 0.126 3.2 0.087 2.2 5⁄8
70-406 1⁄16 - 3⁄8 2-10 12” 300 72 MATB 0.126 3.2 0.087 2.2 1
70-408 3⁄8 - 4 10-100 12” 300 22 TCG 0.126 3.2 0.087 2.2 1
PART # MAT’L THICKNESS DIAMETER KERF PLATE
5/64”-13/64” 5/64”-13/64” 5/64”-13/64” 5/64”-13/64” 5/64”-13/64” 5/64”-13/64”MATERIAL 2-5MM 5-10MM 10-20MM 20-40MM 40-60MM 60-100MM
PA Nylon 2 2 1 1* 1* 1
PC Polycarbonate 2* 2* 2 1 1* 1*
PE Polyethylene 2 2 1 1* 1* 1*
PP Polypropylene 2 1 1 1* 1* 1*
PS Polysulfone 2 2 1 1* 1* 1
ABS Acrylonitrile-Butodiene-Slyrene 2 2 1* 1* 1* 1*
POM Acetol 2 1* 1* 1* 1 1
PVC Polyvinyl Chloride 2 2 1* 1 1* 1
PPO Polyphenylene Oxide 1* 1* 1* 1* 1* 1
PMMA Cast Acrylic 2 2 1 1* 1* 1*
HWG Cotton Laminate Phenolic 2 2* 2* 2 0 0
HP Paper Laminate Phenolic 2 2* 2* 2 0 0
PF Gloss Filled Phenolic 2 2* 2* 2 1 1
PUR Polyethylene 2* 2* 2 2 0 0
HFK Fiberglass 2 2 2 2 0 0
CFK Carbon-Fiber Reinforced Plastics 2 2 2 2 0 0
AFK Aramide Fiber Plastic 2 2 2 2 0 0
0 - Not Recommended20-22 Teeth 1 - Recommended 1* - Highly Recommended60-64 Teeth 2 - Recommended 2* - Highly Recommended
HP CP
Other features of the Onsrud product offering include:
Laser Cut Bodies - true running blade for accurate cutting
Laser Cut Expansion Slots - reduces harmonic vibration for low noise and clean cuts
Laser Cut and Polished Bore - true centering of the blade to the arbor for optimal performance
Recommended for use on table, miter and panel saws MATB - Modified Alternate Top BevelTCG - Triple Chip Grind
THICKNESS
THE
RM
OP
LAS
TIC
STH
ER
MO
SE
TTIN
G P
OLY
ME
RS
Page 113Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
70-500 HSS Plastic DrillNEW
Designed to produce holes in hard andsoft plastic while eliminating edgechipping and chip wrapping.
■ Usage Hard and soft plastic
■ Material See Selection Guide - pg. 2 - 12
FRACTIONAL DRILLS
SP HP
FRAC. DRILLS (CONT.)
LETTER DRILLS
WIRE DRILLS (CONT.)
PART# CED CEL SHK OALDIA70-643 14 (0.182) 23⁄16 0.182 33⁄870-644 15 (0.180) 23⁄16 0.180 33⁄870-645 16 (0.177) 23⁄16 0.177 33⁄870-646 17 (0.173) 23⁄16 0.173 33⁄870-647 18 (0.170) 21⁄8 0.170 31⁄470-648 19 (0.166) 21⁄8 0.166 31⁄470-649 20 (0.161) 21⁄8 0.161 31⁄470-650 21 (0.159) 21⁄8 0.159 31⁄470-651 22 (0.157) 2 0.157 31⁄870-652 23 (0.154) 2 0.154 31⁄870-653 24 (0.152) 2 0.152 31⁄870-654 25 (0.150) 17⁄8 0.150 370-655 26 (0.147) 17⁄8 0.147 370-656 27 (0.144) 17⁄8 0.144 370-657 28 (0.141) 13⁄4 0.141 27⁄870-658 29 (0.136) 13⁄4 0.136 27⁄870-659 30 (0.129) 15⁄8 0.129 23⁄470-660 31 (0.120) 15⁄8 0.120 23⁄4
PART# CED CEL SHK OALDIA70-600 A (0.234) 25⁄8 0.234 37⁄870-601 B (0.238) 23⁄4 0.238 470-602 C (0.242) 23⁄4 0.242 470-603 D (0.246) 23⁄4 0.246 470-604 E (0.250) 23⁄4 0.250 470-605 F (0.257) 27⁄8 0.257 41⁄870-606 G (0.261) 27⁄8 0.261 41⁄870-607 H (0.266) 27⁄8 0.266 41⁄870-608 I (0.272) 27⁄8 0.272 41⁄870-609 J (0.277) 27⁄8 0.277 41⁄870-610 K (0.281) 215⁄16 0.281 41⁄470-611 L (0.291) 215⁄16 0.291 41⁄470-612 M (0.295) 31⁄16 0.295 43⁄870-613 N (0.302) 31⁄16 0.302 43⁄870-614 O (0.316) 33⁄16 0.316 41⁄270-615 P (0.323) 35⁄16 0.323 45⁄870-616 Q (0.332) 37⁄16 0.332 43⁄470-617 R (0.339) 37⁄16 0.339 43⁄470-618 S (0.348) 31⁄2 0.348 47⁄870-619 T (0.358) 3 1⁄2 0.358 47⁄870-620 U (0.368) 35⁄8 0.368 570-621 V (0.377) 35⁄8 0.377 570-622 W (0.386) 33⁄4 0.386 51⁄870-623 X (0.397) 33⁄4 0.397 51⁄870-624 Y (0.404) 37⁄8 0.404 51⁄470-625 Z (0.413) 315⁄16 0.413 51⁄4
PART# CED CEL SHK OALDIA70-561 61⁄64 (0.953) 31⁄8 1⁄2 670-562 31⁄32 (0.969) 31⁄8 1⁄2 670-563 63⁄64 (0.984) 31⁄8 1⁄2 6
PART# CED CEL SHK OALDIA70-502 1⁄8 (0.125) 11⁄2 1⁄8 23⁄470-503 9⁄64 (0.141) 13⁄4 9⁄64 27⁄870-506 5⁄32 (0.156) 115⁄16 5⁄32 31⁄870-509 11⁄64 (0.172) 13⁄4 11⁄64 31⁄470-510 3⁄16 (0.188) 21⁄8 3⁄16 31⁄270-511 13⁄64 (0.203) 27⁄16 13⁄64 35⁄870-512 7⁄32 (0.219) 21⁄2 7⁄32 33⁄470-513 15⁄64 (0.234) 25⁄8 15⁄64 37⁄870-514 1⁄4 (0.250) 27⁄16 1⁄4 470-515 17⁄64 (0.266) 27⁄8 17⁄64 41⁄870-516 9⁄32 (0.281) 215⁄16 9⁄32 41⁄470-517 19⁄64 (0.297) 31⁄16 19⁄64 43⁄870-520 5⁄16 (0.313) 13⁄4 1⁄4 31⁄870-521 21⁄64 (0.328) 35⁄16 21⁄64 45⁄870-522 11⁄32 (0.344) 37⁄16 11⁄32 43⁄470-523 23⁄64 (0.359) 31⁄2 23⁄64 47⁄870-524 3⁄8 (0.375) 21⁄4 1⁄4 43⁄870-525 25⁄64 (0.391) 33⁄4 25⁄64 51⁄870-526 13⁄32 (0.406) 37⁄8 13⁄32 51⁄870-527 27⁄64 (0.422) 315⁄16 27⁄64 53⁄870-528 7⁄16 (0.438) 21⁄2 1⁄4 43⁄470-529 29⁄64 (0.453) 43⁄16 29⁄64 55⁄870-530 15⁄32 (0.469) 45⁄16 15⁄32 53⁄470-531 31⁄64 (0.484) 43⁄8 31⁄64 57⁄870-532 1⁄2 (0.500) 25⁄8 1⁄4 51⁄870-533 33⁄64 (0.516) 31⁄8 1⁄2 670-534 17⁄32 (0.531) 31⁄8 1⁄2 670-535 35⁄64 (0.547) 31⁄8 1⁄2 670-536 9⁄16 (0.563) 31⁄8 1⁄2 670-537 37⁄64 (0.578) 31⁄8 1⁄2 670-538 19⁄32 (0.594) 31⁄8 1⁄2 670-539 39⁄64 (0.609) 31⁄8 1⁄2 670-540 5⁄8 (0.625) 31⁄8 1⁄2 670-541 41⁄64 (0.641) 31⁄8 1⁄2 670-542 21⁄32 (0.656) 31⁄8 1⁄2 670-543 43⁄64 (0.672) 31⁄8 1⁄2 670-544 11⁄16 (0.688) 31⁄8 1⁄2 670-545 45⁄64 (0.703) 31⁄8 1⁄2 670-546 23⁄32 (0.719) 31⁄8 1⁄2 670-547 47⁄64 (0.734) 31⁄8 1⁄2 670-548 3⁄4 (0.750) 31⁄8 1⁄2 670-549 49⁄64 (0.766) 31⁄8 1⁄2 670-550 25⁄32 (0.781) 31⁄8 1⁄2 670-551 51⁄64 (0.797) 31⁄8 1⁄2 670-552 13⁄16 (0.813) 31⁄8 1⁄2 670-553 53⁄64 (0.828) 31⁄8 1⁄2 670-554 27⁄32 (0.844) 31⁄8 1⁄2 670-555 55⁄64 (0.859) 31⁄8 1⁄2 670-556 7⁄8 (0.875) 31⁄8 1⁄2 670-557 57⁄64 (0.891) 31⁄8 1⁄2 670-558 29⁄32 (0.906) 31⁄8 1⁄2 670-559 59⁄64 (0.922) 31⁄8 1⁄2 670-560 15⁄16 (0.938) 31⁄8 1⁄2 6
WIRE DRILLS
PART# CED CEL SHK OALDIA70-630 1 (0.228) 25⁄8 0.228 37⁄870-631 2 (0.221) 25⁄8 0.221 37⁄870-632 3 (0.213) 21⁄2 0.213 33⁄470-633 4 (0.209) 21⁄2 0.209 33⁄470-634 5 (0.206) 21⁄2 0.206 33⁄470-635 6 (0.204) 21⁄2 0.204 33⁄470-636 7 (0.201) 27⁄16 0.201 35⁄870-637 8 (0.199) 27⁄16 0.199 35⁄870-638 9 (0.196) 27⁄16 0.196 35⁄870-639 10 (0.194) 27⁄16 0.194 35⁄870-640 11 (0.191) 25⁄16 0.191 31⁄270-641 12 (0.189) 25⁄16 0.189 31⁄270-642 13 (0.185) 25⁄16 0.185 31⁄2
METRIC DRILLS
PART# CED CEL SHK OALDIA70-714 3.00 (0.118) 41 3.00 7070-715 3.50 (0.138) 44 3.50 7370-716 4.00 (0.157) 54 4.00 8370-717 4.50 (0.177) 56 4.50 8670-718 5.00 (0.197) 62 5.00 9270-719 5.50 (0.217) 64 5.50 9570-720 6.00 (0.236) 70 6.00 10270-721 6.50 (0.256) 73 6.50 10570-722 7.00 (0.276) 73 7.00 10570-723 7.50 (0.295) 78 7.50 11170-724 8.00 (0.315) 81 8.00 11470-725 8.50 (0.335) 87 8.50 12170-726 9.00 (0.354) 89 9.00 12470-727 9.50 (0.374) 92 9.50 12770-728 10.00 (0.394) 95 10.00 13070-729 10.50 (0.413) 98 10.50 13370-730 11.00 (0.433) 103 11.00 14070-731 11.50 (0.453) 106 11.50 14370-732 12.00 (0.472) 111 12.00 14970-733 12.50 (0.492) 114 12.50 15270-734 13.00 (0.512) 114 13.00 15270-735 13.50 (0.531) 122 13.50 16870-736 14.00 (0.551) 122 14.00 16870-737 14.50 (0.571) 122 14.50 16870-738 15.00 (0.591) 132 15.00 18170-739 15.50 (0.610) 132 15.50 18170-740 16.00 (0.630) 132 16.00 18170-741 16.50 (0.650) 132 16.50 18170-742 17.00 (0.669) 143 17.00 19470-743 17.50 (0.689) 143 17.50 194
NO Wrapping
NO Cleaning
NO Melting
NO SurfaceMarring
NO InterruptedOperation
Page 114
72-000 Solid Carbide Boring BitsNEW Two style of tools are available in this
series. The brad point drill is designed tocut blind holes and produce a clean edgeon the top surface. The 60° through drillis designed to produce through holeswhile providing clean edges on both sides.
■ Usage Wood
■ Material See Selection Guide - pg. 2 - 12
PART # CED SHANK OAL PART # CED SHANK OAL
72-001 3 10 57 72-021 3 10 70
72-005 5 10 57 72-025 5 10 70
72-009 6 10 57 72-029 6 10 70
72-013 8 10 57 72-033 8 10 70
ThroughHole
BradPoint
BRAD POINT - designed to produce a blind holewhile preventing fraying on the top edge.
HINGE BIT - This 35mm carbide tipped bit isdesigned to produce a flat bottom hole with cleanedges for hinge mounting.
Right Hand Rotation
PART # CED SHANK OAL PART # CED SHANK OAL
72-002 3 10 57 72-022 3 10 70
72-006 5 10 57 72-026 5 10 70
72-010 6 10 57 72-030 6 10 70
72-014 8 10 57 72-034 8 10 70
Left Hand Rotation
PART # CED SHANK OAL PART # CED SHANK OAL
72-053 3 10 57 72-075 3 10 70
72-057 5 10 57 72-079 5 10 70
72-061 6 10 57 72-083 6 10 70
72-065 8 10 57 72-087 8 10 70
THROUGH HOLE (60° POINT) - produces a throughhole and reduces fraying on the entry and exit edges.
Right Hand Rotation
PART # CED SHANK OAL PART # CED SHANK OAL
72-054 3 10 57 72-076 3 10 70
72-058 5 10 57 72-080 5 10 70
72-062 6 10 57 72-084 6 10 70
72-066 8 10 57 72-088 8 10 70
Left Hand Rotation
SW CWHW
PART # CED SHK OAL
72-097 35 10 57 Hinge
77-000 Single Edge - Solid CarbideNEW Top Loading Router Bit
Designed to produce fast, clean cutsin plastic and aluminum.
■ Usage Plastic and aluminum
■ Material See Selection Guide - pg. 2 - 12
77-000 SERIES - PLASTIC
PART # CED CEL SHK DIA OAL
77-002 1⁄165⁄16
11⁄64 61⁄2
77-004 1⁄8 5⁄1611⁄64 61⁄2
77-012 1⁄165⁄16
1⁄4 61⁄2
77-014 1⁄8 5⁄161⁄4 61⁄2
77-016 3⁄163⁄8 1⁄4 61⁄2
77-018 1⁄4 3⁄8 1⁄4 61⁄2
1/8" shank tools need to be custom ordered
SP HP A
77-025 SERIES - ALUMINUM
PART # CED CEL SHK DIA OAL
77-025 1⁄165⁄16
11⁄64 61⁄2
77-027 1⁄8 5⁄1611⁄64 61⁄2
77-033 1⁄165⁄16
1⁄4 61⁄2
77-035 1⁄8 5⁄161⁄4 61⁄2
77-037 3⁄163⁄8 1⁄4 61⁄2
77-039 1⁄4 3⁄8 1⁄4 61⁄2
Page 115Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
77-100 Double or Three EdgeNEW Solid Carbide Taper Tools
The taper tools are available with a variety of taper angles and come standard with a ball nose point.The tools are designed to produce a good edge finish in a wide variety of materials.
■ Usage Wood, plastic and aluminum
■ Material See Selection Guide - pg. 2 - 12SW HW SP HP A
PART# CED CEL SHK OAL ANGLE RADIUSPER SIDE
77-102 1⁄8 11⁄2 1⁄4 3 1° 1⁄16
77-104 1⁄8 1 1⁄4 3 3° 1⁄16
77-106 1⁄8 3⁄4 1⁄4 3 5° 1⁄16
77-108 1⁄8 1⁄2 1⁄4 3 7° 1⁄16
Custom tools can be made upon request
PART# CED CEL SHK OAL ANGLE RADIUSPER SIDE
77-112 1⁄4 2 1⁄2 4 3° 1⁄8
77-114 1⁄4 13⁄8 1⁄2 4 5° 1⁄8
77-116 1⁄4 1 1⁄2 4 7° 1⁄8
PART # CED CEL SHK DIA OAL
80-003 .165 11⁄16 .1875 21⁄2
80-000 High Speed SteelTaper Pin Router
These three flute upcuts with atapered flute are used for profilingand trimming primarily in aircraftassembly operations.
■ Usage Aluminum and non-abrasive hard plastics
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL
80-001 .081 3⁄4 .098 2
80-002 .110 7⁄8 .128 21⁄4
HELIX ANGLE ≈ 24°
81-000 Double Edge - High Speed SteelLo Helix
These lo helix upcut spirals weredeveloped for CNC routers usedprimarily in the aircraft industry.They are designed with maximumstrength of configuration to cutT, O or combined stacks ofaluminum-using coolant.
■ Usage Aluminum
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL SHK DIA OAL HELIX ALUM CONDITION
81-001 1⁄4 3⁄4 1⁄2 31⁄16 5° T
81-003 5⁄16 3⁄4 1⁄2 31⁄16 10° C
81-004S 5⁄16 3⁄4 1⁄2 31⁄16 10° O
81-007 21⁄64 3⁄4 1⁄2 31⁄16 10° C
81-005 3⁄8 3⁄4 1⁄2 31⁄16 5° T
S = Single Edge
A
A
Page 116
Designed for reduced vibrationproducing smoother finish cuts.Extended reach during side thinningand gage reduction. Longer tool lifeto reduce tool changes.
■ Usage Extrusion and sheet aluminum. Optimizedfor use on multi-head extrusion mills CNCmills and routers
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL ERL SHK DIA OAL HELIX & DIR FLUTES CNR RAD ALUMINUM MACH ENVCHAMFER CONDITION
Tolerance +.002 ±.03 +.0000 ±.03
81-103 5⁄16 13⁄16 - 1⁄2 3 10° RH 2 .02 x 45° C Wet
81-111 21⁄64 3⁄4 - 1⁄2 3 10° RH 2 .02 x 45° C Wet
81-104 3⁄8 13⁄16 - 1⁄2 3 10° RH 2 .02 x 45° O Wet
81-106 1⁄2 1 - 1⁄2 31⁄2 3° RH 2 .02 x 45° O Wet
81-108 5⁄8 1 - 5⁄8 31⁄2 3° RH 2 .02 x 45° C Wet
UPCUT
-.0005
81-100 Solid Carbide Spiral ExtrusionCutters
A
Page 117Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
81-200 Double Edge - Solid Carbide81-500 Upcut Spiral Cutters
Engineered for machining monolithicparts on CNC mills, CNC routersand multi-head machining centers -Slot cutters and high speed deepcavity cutting.
■ Usage Aluminum slabs or plates, thin walledstructures and supports
■ Material See Selection Guide - pg. 2 - 12
PART # CED CEL ERL SHK DIA OAL HELIX & DIR FLUTES CNR RAD MACH ENVCHAMFER
81-502 6mm 10mm 28 6mm 64mm 40° RH 2 .5mm Coolant Req.
81-504 8mm 10mm 28 8mm 64mm 40° RH 2 .5mm Coolant Req.
81-506 10mm 12mm 24 10mm 64mm 40° RH 2 .5mm Coolant Req.
81-508 12mm 19mm 31 12mm 76mm 40° RH 2 .5mm Coolant Req.
81-510 14mm 19mm 38 14mm 76mm 40° RH 2 .5mm Coolant Req.
81-512 16mm 19mm 41 16mm 88mm 40° RH 2 .5mm Coolant Req.
81-514 18mm 22mm 44 18mm 100mm 40° RH 2 .5mm Coolant Req.
81-516 20mm 25mm 52 20mm 100mm 40° RH 2 .5mm Coolant Req.
HELIX ANGLE ≈ 40°
METRIC
PART # CED CEL ERL SHK DIA OAL CNR RAD
81-200S 1⁄8 1⁄4 1⁄2 1⁄8 2 0.002
81-203S 3⁄16 3⁄8 7⁄8 3⁄16 2 0.002
81-204S 1⁄4 3⁄8 11⁄8 1⁄4 21⁄2 0.002
81-208S 3⁄8 1⁄2 11⁄8 3⁄8 21⁄2 0.002
81-217S 1⁄2 3⁄4 11⁄2 1⁄2 3 0.002
81-224S 5⁄8 3⁄4 15⁄8 5⁄8 31⁄2 0.002
81-237S 3⁄4 11⁄4 2 3⁄4 4 0.002
81-238S 1 11⁄2 31⁄8 1 5 0.002
HELIX ANGLE ≈ 40°
PART # CED CEL ERL SHK DIA OAL CNR RAD
81-200 1⁄8 1⁄4 1⁄2 1⁄8 2 0.005
81-201 5⁄32 5⁄16 5⁄8 3⁄16 2 0.005
81-203 3⁄16 3⁄8 7⁄8 3⁄16 2 0.008
81-204 1⁄4 3⁄8 11⁄8 1⁄4 21⁄2 0.020
81-206 5⁄16 1⁄2 11⁄8 5⁄16 21⁄2 0.020
81-208 3⁄8 1⁄2 11⁄8 3⁄8 21⁄2 0.020
81-212 3⁄8 3⁄4 - 3⁄8 3 0.020
81-213 3⁄8 1⁄2 21⁄8 3⁄8 4 0.020
81-214 1⁄2 5⁄8 13⁄8 1⁄2 3 0.020
81-216 1⁄2 3⁄4 11⁄2 1⁄2 3 0.020
81-218 1⁄2 5⁄8 21⁄8 1⁄2 4 0.020
81-220 1⁄2 5⁄8 31⁄8 1⁄2 5 0.020
81-224 5⁄8 3⁄4 15⁄8 5⁄8 31⁄2 0.020
81-228 3⁄4 1 15⁄8 3⁄4 4 0.020
81-232 3⁄4 1 21⁄2 3⁄4 6 0.020
81-236 3⁄4 11⁄4 2 3⁄4 4 0.020
81-238 1 11⁄2 31⁄8 1 5 0.020
HELIX ANGLE ≈40°
A
Page 118
■ Usage Plastics and composites
■ Material See Selection Guide - pg. 2 - 12
82-100 Insert Milling Cutters
Designed for smooth finishes over awide range of materials.
DOUBLE EDGE END MILL
THREE EDGE END MILL
PART # CED CEL ARBOR DIA OAL FLUTES INSERT SCREW WRENCH
82-120 2 .590 3⁄4 21⁄8 3 82-022 82-054 82-055
82-122 21⁄2 .590 1 21⁄8 4 82-022 82-054 82-055
82-124 3 .590 1 21⁄8 5 82-022 82-054 82-055
SHELL MILL
PART # CED CEL ERL SHK DIA OAL INSERT SCREW WRENCH
82-104* 1 .530 2 1 41⁄4 82-016 82-052 82-055
82-106* 11⁄4 .530 2 11⁄4 41⁄4 82-016 82-052 82-055
82-105 1 .530 2 3⁄4 8 82-016 82-052 82-055
82-107 11⁄4 .530 2 1 8 82-016 82-052 82-055
* Supplied with Weldon Flats on the shank
PART # CED CEL ERL SHK DIA OAL INSERT SCREW WRENCH
82-108* 11⁄2 .530 2 11⁄4 47⁄8 82-016 82-052 82-055
82-109 11⁄2 .530 2 11⁄4 8 82-016 82-052 82-055
* Supplied with Weldon Flats on the shank
SP HP
PART # DESCRIPTION
33-155 ISO 30 x 3⁄4" Toolholder
33-157 ISO 30 x 1" Toolholder
33-165 HSK 63F x 3⁄4" Toolholder
33-167 HSK 63F x 1" Toolholder
SHELL MILL ARBOR
NEW TOOLS in BOLD
Page 119Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
82-200 Single Or Double Edge -NEW Indexable Insert CNC Insert Tooling
The offering consists of singleedge or double edge tools speciallydesigned to cut natural or compositewood products. An indexable insert tool offers the advantage of quicker setups, consistentdiameter after insert indexing, and eliminates the need to have tools resharpened.
■ Usage Wood
■ Material See Selection Guide - pg. 2 - 12SW CWHW
82-202/82-204 SINGLE EDGEPART # CED CEL SHK OAL DESCRIPTION
82-202 18mm 50mm 25mm 125mm 18mm RH Insert Cutter
82-240 Periphery Insert – 50 x 12 x 1.5 - 10 Pack
82-241 Periphery Insert 2 – 30 x 12 x 1.5 - 10 Pack
SPARE 82-260 Periphery Screw m4x5PARTS 82-246 Plunge Tip Insert – 7.5 x 12 x 1.5 - 10 Pack
82-261 Plunge Tip Screw – m4x5
Torx Size – Tx15
82-204 3⁄4 2 3⁄4 41⁄2 3⁄4 RH Insert Cutter
82-240 Periphery Insert – 50 x 12 x 1.5 - 10 Pack
82-241 Periphery Insert 2 – 30 x 12 x 1.5 - 10 Pack
SPARE 82-260 Periphery Screw m4x5PARTS 82-246 Plunge Tip Insert – 7.5 x 12 x 1.5 - 10 Pack
82-261 Plunge Tip Screw – m4x5
Torx Size – Tx15
82-224 DOUBLE EDGEPART # CED CEL SHK OAL DESCRIPTION
82-224 30mm 50mm 25mm 125mm 30mm DE Insert router bit with plunge tip RH
82-245 Periphery Insert – 50 x 12 x 1.5 - 10 Pack
SPARE82-260 Periphery Screw m4x5
PARTS 82-247 Plunge Tip Insert – 12 x 12 x 1.5 - 10 Pack
82-261 Plunge Tip Screw – m4x5
Torx Size – Tx15
Page 120
PART # CED CEL SHK DIA OAL
86-012 1⁄4 2 1⁄4 31⁄4
86-014 5⁄16 23⁄8 5⁄16 33⁄4
86-016 3⁄8 23⁄4 3⁄8 41⁄4
86-018 7⁄16 27⁄8 7⁄16 41⁄2
86-020 1⁄2 3 1⁄2 43⁄4
86-000 Solid Carbide Kevlar DrillNEW
This tool is designed to drill Aramidmaterials and produce a clean hole. Thespecific point design shears the aramidfibers eliminating whiskers or delamination.
PART # CED CEL SHK DIA OAL
86-002 #39 (.0995) 11⁄4 0.099 21⁄4
86-004 1⁄8 11⁄4 1⁄8 21⁄4
86-006 #30 (.129) 11⁄4 0.129 21⁄4
86-008 #26 (.147) 13⁄8 0.147 21⁄2
86-010 3⁄16 15⁄8 3⁄16 23⁄4
■ Usage Aramid materials
■ Material See Selection Guide - pg. 2 - 12CP
82-200 Single Edge -NEW Indexable Insert CNC Insert Tooling
82-206/82-220 SINGLE EDGEPART # CED CEL SHK OAL DESCRIPTION
82-206 5⁄16 25⁄32 1⁄2 23⁄8 5⁄16 Insert router bit RH
82-242 Periphery Insert – 20 x 4.1 x 1.1 - 10 PackSPARE
82-280 Clamping Wedge Torx Size – Tx8PARTS82-262 Clamping Wedge Screws – M2.5 x 5
82-208 3⁄8 25⁄32 1⁄2 23⁄8 3⁄8 Insert router bit RH
82-242 Periphery Insert – 20 x 4.1 x 1.1 - 10 PackSPARE
82-280 Clamping Wedge Torx Size – Tx8PARTS82-263 Clamping Wedge Screws – M2.5 x 5.5
82-210 1⁄2 23⁄16 1⁄2 27⁄8 1⁄2 Insert router bit RH
82-243 Periphery Insert – 30 x 5.5 x 1.1 - 10 PackSPARE
82-281 Clamping Wedge Torx Size – Tx8PARTS82-264 Clamping Wedge Screws – M3 x 7
82-212 5⁄8 2 1⁄2 311⁄16 5⁄8 Insert router bit RH
82-244 Periphery Insert – 50 x 5.5 x 1.1 - 10 PackSPARE
82-282 Clamping Wedge Torx Size – Tx15PARTS82-265 Clamping Wedge Screws – M4 x 11.5
82-214 3⁄4 2 1⁄2 311⁄16 3⁄4 Insert router bit RH
82-244 Periphery Insert – 50 x 5.5 x 1.1 - 10 PackSPARE
82-282 Clamping Wedge Torx Size – Tx15PARTS82-265 Clamping Wedge Screws – M4 x 11.5
82-216 3⁄8 25⁄32 1⁄2 23⁄8 3⁄8 Insert router bit LH
82-242 Periphery Insert – 20 x 4.1 x 1.1 - 10 PackSPARE
82-280 Clamping Wedge Torx Size – Tx8PARTS82-263 Clamping Wedge Screws – M2.5 x 5.5
82-218 1⁄2 13⁄16 1⁄2 23⁄4 1⁄2 Insert router bit LH
82-243 Periphery Insert – 30 x 5.5 x 1.1 - 10 PackSPARE
82-281 Clamping Wedge Torx Size – Tx8PARTS82-264 Clamping Wedge Screws – M3 x 7
82-220 3⁄4 131⁄32 3⁄4 41⁄4 3⁄4 Insert router bit LH
82-244 Periphery Insert – 50 x 5.5 x 1.1 - 10 PackSPARE
82-282 Clamping Wedge Torx Size – Tx15PARTS82-265 Clamping Wedge Screws – M4 x 11.5
The offering consists of singleedge or double edge tools speciallydesigned to cut natural or compositewood products. An indexable insert tool offers the advantage of quicker setups, consistentdiameter after insert indexing, and eliminates the need to have tools resharpened.
■ Usage Wood
■ Material See Selection Guide - pg. 2 - 12SW CWHW
Page 121Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
PART # CED SHK DIA SHK LNGTH # OF WINGS
91-000* 11⁄4 1⁄2 11⁄2 2
91-102 21⁄2 1⁄2 2 2
91-106 4 3⁄4 21⁄4 3
* = Carbide Tipped
Note: 90-002, 90-004, 90-006 & 90-008 use 91-125 insert and 91-130 screw90-014 use 91-127 insert and 91-130 screw
STRAIGHT UP-SHEAR
PART # CED SHK DIA SHK LNGTH # OF WINGS
91-104 21⁄2 1⁄2 2 2
91-108 4 3⁄4 21⁄4 3
91-114* 4 3⁄4 21⁄4 3
* Radius edges excellent for plastic and aluminum surfacing.
PART # DESCRIPTION
91-125 Insert 10/pk
91-127 Radius Insert 10/pk
91-130 Screw M4 (Old Version)
91-133 Screw M5
91-136 Wrench
These tools are dynamically balanced and approved for use on CNC routers. Max RPM 18,000 1⁄8” Depth of cut MAX.
* DOC = Maximum Depth of Cut Proper running speed for
Spoilboard Surfaces: 21⁄2” diameter tools should be fed at 200-600 IPM at 12,000-16,000 RPM. 4” diameter tools should be fed at 200-600 IPM at 12,000-14,000 RPM.
* Do Not Exceed 1/8” Depth Per Pass
NEW TOOLS in BOLD
■ Usage Aluminum, plastics and composite wood
■ Material See Selection Guide - pg. 2 - 12
91-000 Spoilboard Surfacing Cutters91-100NEW
Designed for surfacing MDF,particalboard and balsa core where“flow through” or “high flow” fixturingis employed using large capacityvacuum pumps. This method ofsurfacing spoilboards allows formuch faster table planing.
Insert Style
Carbide Tipped
SP HP A CW
ROUTER SELECTION GUIDEThe selection guide on pages 2 - 12 is a place to start making a bit selection or a place to check your current bit selection. You shouldtry several tools and more than one tool geometry before you settle on the best tool for you specific router, set-up, fixturing and otherenvironmental conditions.
How To Order – Onsrud Cutter products are sold solely through industrial distribution. You may place an order through the authorizeddistributor in you market area. Should you wish the name of that distributor, please call Onsrud Cutter.
Guarantee – Onsrud Cutter products are guaranteed against defects in material and quality of manufacture when used in the propermanner. Onsrud Cutter will repair or replace tools, which have been authorized for return, if upon inspection such tools are found to bedefective due to material or manufacture.
Router Laboratory – Customers, as a routine, send us panels (2’ x 2’) with router and feed specifications several weeks prior to thestart of a new run. (We are able to duplicate most production environments in the Router Laboratory.) Armed with material, router type,spindle speed, feed rate, set up and type of cut to be made, Onsrud Cutter can make a specific tool recommendation for test andevaluation in your operational environment. Should you have difficult-to-cut material or should you wish to verify your current toolselection, call the Onsrud Cutter Engineering Department and arrange for a Router Laboratory test.
GENERAL GUIDELINES FOR TOOL MATERIAL AND GEOMETRY
TOOL MATERIALS __________________________________________
Solid Carbide Use for fibrous or abrasive plastics.
Carbide Tipped Use for general plastic cutting applications.
High Speed Steel Use for optimum surface finish.
TOOL GEOMETRY __________________________________________
Straight Flute Use for plastic hand feed applications.
Spiral Flute Use for plastic automatic feed applications.
FLUTE GEOMETRY __________________________________________________________
Single Flute Use for faster feed rates in softer materials.
Double Flute Use for better finish in harder materials.
Upcut Spiral Use for grooving or slotting, for upward chip evacuation and best finish
on bottom side of piece part.
Downcut Spiral Use for downward chip flow, better hold down in fixture and best finishon top side of piece part.
Up/Down Spiral Use for double laminated material and best finish on top and bottomside of piece part.
Page 122
Technical Data
TOOL SELECTION
TOOL MATERIAL• Solid Carbide: Primarily used in CNC operations. Material provides best rigidity and long tool life.• Carbide Tipped: Incorporates the wear resistance of carbide and the toughness of a
HSS body-mainly hand held.• HSS: Primarily used in hand routing. Material provides a tough body and sharper
cutting edge. Good in CNC.
FLUTE GEOMETRY• Straight flute: Offers a neutral cutting action - highest force• Upcut flute: Provides the best surface finish and allows for good chip extraction.
May cause part lifting if vacuum or fixturing is not sufficient.• Downcut flute: Provides a downward force which helps eliminate part lifting. Chip rewelding
MAY occur if there is no space below the part for chip expansion.• Compression: Used for laminated materials, produces a good top and bottom finish on the part.
NUMBER OF FLUTES• Single Flute: Allows for larger chiploads in softer materials• Double Flute: Allows for better part finish in harder materials.• Multiple Flutes: Allows for an even better part finish in harder materials.
Note: As the number of cutting edges increase, your feed rate should increase to prevent burning and premature tool dulling.
OPTIMIZING SPEED AND FEEDS
1. Start off using the recommended chipload and RPM for the material you are cutting.2. Increase the feedrate until the part finish starts to decrease or you risk moving the part off the vacuum.
Decrease the feed by 10%.3. Next decrease your RPM by a set increment until your surface finish deteriorates again.
Once this happens increase your RPM until the finish is acceptable.4. You have now optimized your speed and feed by taking the largest chip possible.
Note: This should be done in the first sheet of material to prevent tool dulling due to excessive heat.
TOOL HEATIf a feed rate is too low, heat will be generated causing the cutting edge to break down and dull quickly. To check this,run a nest of parts and stop the spindle. When the spindle has stopped rotating, carefully feel the tool’s temperature.It should be at or near room temperature. If the tool is hot, review “Optimizing Speed and Feeds”.
OAL= overall length CEL= cutting edge lengthCED = cutting edge dia.
Basic Terms
Page 123Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Technical Data
FIXTURING METHODS
FLOW THROUGH VACUUMThis style uses LDF (Low Density Fiberboard) or MDF (Medium Density Fiberboard) as a sacrificial surfacefor sheet material to be cut on. The porous nature of LFD or MDF allows vacuum to pass through allowingthe material to be held in place for machining. As parts are cut out of the sheet material, vacuum loss startsto occur from the slot produced by the cutting tool. This can lead to part lifting or movement especially insmall parts. Cutter diameter will also influence part movement. A 1/2 diameter tool will exert 25% more lateralpressure than a 3/8 diameter tool.
When cutting small parts in sheet material, one may want to consider tab or skin cutting to prevent part movement.
DEDICATED SPOILBOARDDedicated spoilboards are used for reoccurringproduction runs where optimal cycle times areneeded. This work holding method creates vacuumchambers in the sacrificial board specifically to theshape of the parts being cut. This elimination of vacuumloss relates to improved cycle times and part finish.
STEPS TO CREATE A DEDICATED SPOILBOARD:1. Surface both sides of your MDF board2. Lay out the part pattern on the MDF and determine
quantity that will fit.3. Cut the part profile into the MDF board using a larger
diameter tool than would normally cut the part.Make your slot depth 1 to 1.5 times the cutter diameter.
4. A gasket groove must be cut next inside the part profileto create a vacuum seal. The groove should be 1/2 thegasket material thickness to allow for proper compression.
5. A grid pattern must then be cut inside the gasket groove todistribute the vacuum evenly through out the vacuum area.
6. Drill holes through out the pattern in the intersectionsof the vacuum grid until there is no resistance on yourvacuum gage on the machine table.
7. Seal the board using rubberized coatings, polyurethanesealers or a sanding sealer to prevent vacuum frompassing through the board in unwanted areas.
8. Apply the gasket tape.
This operations sounds time consuming. It will be for your first board. Once you become familiar making thesefixtures, you will make up for it in your cycle time reductions and part finish. A lot of headaches and problems can beresolved by using the proper work holding.
RAISED SPOILBOARDThis is generally used where secondary operations are needed and the spoilboard will interfere with the secondary tool.
Raised spoilboards are another type of fixturing that works well for routing parts such as circles from squares where the scrap or off-fall is of such a size to be potentially harmful to the tool and or operator when it is cut free. A raisedspoilboard should make sure the off-fall would not interfere with the first and second tool and that the off-fall would befree and clear of the tool path.
SURFACING SPOILBOARDSWhen creating new fixtures or using a new MDF sheet, the spoilboard must be surfaced to level the board to themachine table. This consists using a large diameter cutter (OC 91-100 series) to quickly level the entire surface.
The following benefits will be achieved by surfacing your spoilboard:• Leveling material to get consistent cuts.• Remove grooves caused by routing.• Reduce vacuum loss due to clogged pores at the material surface due to dust and chips.• Preventing material warpage caused by humidity in summer time.
Proper SpoilboardTechniques
Page 124
Technical Data
COLLETING
COLLET LIFE SPANCollets have a life span of 3 months if used 8 hours a day. Replacing the collets will ensure your operation runs consistentlyand prevents tool breakage. When inserting a tool into the collet make sure the flute fadeout does not enter the collet. Thiswill cause run out and potentially lead to tool breakage. To ensure proper clamping the tool shank should fill, at the minimum,80% of the depth of the collet. If this can not be achieved, use a collet life plug to ensure a proper clamping effect.
COLLET MAINTENANCECleaning is an essential part of collet maintenance. As material is cut it causes the collet, tool holder, collet nut and spindleto become dirty. This causes your tool to cut in an elliptical fashion which will decrease tool life and cause inconsistency inyour operation. Collets, tool holder, and collet nut should be cleaned daily using the Rust Free solvent and a brass brush(OC series 33-21 and 33-10). Refer to the critical areas diagram to see which surfaces must be clean.
CLEANING INSTRUCTIONS1. Spray the cleaner on the surface and allow it to soak for a minute2. Use a brass brush to clean the surface thoroughly.3. Rinse off using distilled alcohol. Feel the surface using your fingers
to make sure the surface is clean4. Apply a small amount of Lubricant T-9 to prevent rusting.
TOOL BREAKAGE
If a condition arises where multiple tools should break, follow these steps to solve your problem:1. Are you using the proper tool for the job?2. Make sure your collets and tool holders are clean and the tool is colleted properly.3. Check your speed and feed (is your tool hot?)4. Is your depth of cut too excessive for the material you’re cutting?5. Do you have any part movement?6. Do you have ample part hold down?7. Stop running parts and check with your distributor or Onsrud’s Technical Support.
If you have to contact your distributor or Technical Support, have the following information:1. Machine being used.2. Material being cut.3. Part number of tool along with the batch number which is below the part number.4. Speed / Feed / Depth of cut.5. Where did the tool break (flute, shank, or in the collet)?6. How long did the tool work before it broke?7. Have you done this operation in the past using this tool?
CRITICALCLEANAREAS CRITICAL
CLEANAREAS
INSIDETAPER
BEARING STYLE NUT BEARING STYLE NUT
STANDARD SPINDLE
QUICK CHANGEBT30 TOOL HOLDER
INSIDETAPER
Page 125Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Hard Wood Cutting Data
DEPTH OF CUT: 1 x D Use recommended chip load2 x D Reduce chip load by 25%3 x D Reduce chip load by 50%
APPLICATION GOOD BETTER BEST
Single Pass 82-200 52-200/57-200 60-300/60-350
Roughing 82-200 60-000 60-850
Finishing 60-300/60-350 60-200
HW
FORMULAS: Chip Load = Feed Rate / (RPM x # of cutting edges)Feed Rate (IPM) = RPM x # of cutting edges x chip loadSpeed (RPM) = Feed Rate / (# of cutting edges x chip load)
DEFINITIONS: IPM = Inches Per MinuteIPR = Inches Per Revolution
CHIP LOAD PER TOOTH
Cutting Edge DiameterSeries Cut 1/16 3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1 1/8 1 1/4 1 1/2 1 3/4 2
12-00 1 x D .002-.004 .002-.004 .002-.004 .003-.005 .003-.005 .004-.006 .004-.006 .005-.007 .005-.007 .005-.007 .006-.008 .007-.009 .010-.012 .011-.013 .012-.014 .013-.015 .014-.016 .015-.017 .016-.018
37-50/60 1/2 CED .002-.004 .002-.004 .002-.004 .003-.005 .005-.007 .007-.009
37-80 1 x D .004-.006 .004-.006* .004-.006**
38-50/60 1/2 CED .001-.003 .002-.004 .002-.004 .002-.004 .003-.005 .004-.006 .005-.007
40-50 1 1/2 .003-.005
40-000 1 x D .006-.008 .006-.008 .007-.009 .007-.009 .008-.010 .008-.010 .009-.007 .010-.012
40-100 1 x D .004-.006 .005-.007 .005-.007 .005-.007 .006-.008 .006-.008 .007-.009 .009-.011
48-000 1 x D .004-.006 .005-.007 .005-.007 .005-.007 .005-.007 .006-.008 .006-.008 .007-.009 .008-.010 .009-.011 .010-.012 .011-.013 .012-.014 .013-.015 .014-.016 .015-.017
48-500 1 x D .005-.007 .005-.007 .006-.008 .008-.010
52-200/
57-200 1 x D .003-.005 .003-.005 .004-.006 .004-.006 .005-.007 .005-.007 .006-.008 .006-.008 .007-.009 .007-.008 .008-.010 .009-.011
52-400/57-400 1 x D .004-.006 .004-.006 .005-.007 .005-.007 .006-.008 .007-.009 .007-.009 .008-.010 .009-.011 .010-.012
52-900 1 x D .006-.008 .007-.009 .007-.009
56-200 1 x D .003-.005 .003-.005 .004-.006 .004-.006 .005-.007 .005-.007 .006-.008 .006-.008 .007-.009 .008-.010 .009-.011
57-900 1 x D .005-.007 .006-.008 .007-.009
60-000 (LH) 1 x D .013-.015 .014-.016 .016-.018 .017-.019
60-000 (HH) 1 x D .015-.017 .017-.019 .019-.021 .021-.023
60-090 1 x D .005-.007
60-100 1 x D .010-.012 .012-.014 .014-.016 .016-.018 .018-.020 .020-.022 .022-.024
60-100DE 1 x D .014-.016 .016-.018 .018-.020 .020-.022 .022-.024
60-1003E 1 x D .016-.018 .018-.020 .022-.024
60-100C 1 x D .019-.021 .021-.023 .023-.025 .025-.027
60-200/67-470 1 x D .002-.004 .004-.006 .005-.007 .009-.011
60-300/60-400 1 x D .019-.021 .021-.023 .023-.025 .025-.027
60-350/60-430 1 x D .016-.018 .018-.020 .022-.024
60-500/500M 1 x D .013-.015 .015-.017 .016-.018
60-600 1 x D .018-.020 .020-.022 .022-.024
60-700 1 x D .018-.020 .020-.022 .022-.024
60-800 1 x D .017-.019 .019-.021 .021-.023 .023-.025
60-850 1 x D .017-.019 .019-.021
60-900 1 x D .015-.017 .017-.019
60-950 1 x D .019-.021 .021-.023
61-200 1 x D .007-.009 .008-.010 .009-.011 .009-.011 .010-.012 .011-.013
62-200/63-200 1 x D .010-.012 .011-.013 .012-.014 .012-.014 .013-.015 .014-.016
64-000/65-000 1 x D .001-.003 .002-.004 .003-.005 .004-.006 .005-.007
77-100 (DE) 1 x D .003-.005
77-100 (3E) 1 x D .005-.007
82-200 (SE) 1 x D .006-.008 .006-.008 .007-.009 .008-.010 .009-.011
82-200 (DE) 1 x D .007-.009
* = 16,000 RPM** = 15,000 RPM
Page 126
ClibPDF - www.fastio.comPage 127
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 128
ClibPDF - www.fastio.comPage 129
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 130
ClibPDF - www.fastio.comPage 131
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 132
ClibPDF - www.fastio.comPage 133
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 134
ClibPDF - www.fastio.comPage 135
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 136
ClibPDF - www.fastio.comPage 137
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 138
ClibPDF - www.fastio.comPage 139
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 140
ClibPDF - www.fastio.comPage 141
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 142
ClibPDF - www.fastio.comPage 143
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 144
ClibPDF - www.fastio.comPage 145
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 146
ClibPDF - www.fastio.comPage 147
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 148
ClibPDF - www.fastio.comPage 149
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 150
ClibPDF - www.fastio.comPage 151
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 152
ClibPDF - www.fastio.comPage 153
Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 154
Page 155Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 156
WHITESIDE MACHINE COMPANY
Part Cutting Bore Kerf No. Number Diameter Flutes
6800 1 1/4" 3/8"-24thd 3/16" 4 6801 1 1/4" 3/8"-24thd 3/16" 6 6804 1 1/4" 3/8"-24thd 1/4" 4 6805 1 1/4" 3/8"-24thd 1/4" 6
DRAWER SLOT CUTTERS(Jemco Machines)
DRAWER SLOT CUTTER ARBORS
SLOTTING CUTTER ARBORSIncludes B5 Bearing for 1/2" depth of cut. Part Shank Overall Number Size Length A200B 1/4" 2 3/8" A205B 3/8" 2 3/8" A210B 1/2" 2 3/8" A220B 1/2" 4"Note - A220B has an extra long shank for extended reach.All include B5 Bearing for 1/2" depth of cut. Use B20 Bearing for 9/16" depth of cut. Use B25 Bearing for 3/8" depth of cut. Use B26 Bearing for 1/4" depth of cut. Use B27 Bearing for 5/8" depth of cut.
PART #6705A
Part Number Kerf 3 wing 4 wing Decimal Fractional 6700A 6700B .062 1/16" 6701A .070 --- 6702A .080 --- 6703A 6703B .094 3/32" 6704A .100 --- 6704C .110 7/64" 6705A 6705B .125 1/8" 6708A .156 5/32" 6709A .187 3/16" 6709C .218 7/32" 6710A 6710B .250 1/4" 6712A .281 9/32"Special Sizes Available Upon Request
SLOTTING CUTTERS1 7/8"Cutting Diameter - 5/16" Bore
Part Shank Overall Thread Number Diameter Length
6890 1/4" 2" 3/8"-24 6891 3/8" 2" 3/8"-24 6892 1/2" 2" 3/8"-24 6896 3/8" 3 1/4" 3/8"-24
Part Size Number 6902 1/8" x 5/8" x 4" 6904 1/8" x 5/8" x 6" 6906 1/8" x 5/8" x 8" 6910 1/8" x 3/4" x 4" 6912 1/8" x 3/4" x 6" 6914 1/8" x 3/4" x 8"Sold Individually
POLISHED SOLID CARBIDE KNIVES
SPOILBOARD • SLOTTING
PART #6912
PART #6800
PART #6891
CNC SPOILBOARD SURFACING
Part Large Shank # of Number Diameter Size Wings
STRAIGHT CUT SB25-2 2 1/2" 1/2" 2 SB40-2 4" 3/4" 2 SB40-3 4" 3/4" 3
UP SHEAR CUT SBU25-2 2 1/2" 1/2" 2 SBU40-3 4" 3/4" 3
CARBIDE INSERTS INDEXABLE - 4 CUTTING EDGES Part Number Description Size
SB-Insert 10 Pc. Insert Pak 14 mm x 14mm x 2mm SB Screw Replacement Insert Screw M5x7 SB Wrench Insert Wrench T-15 Torx
PART # SB25-2
Part I.D. O.D. Overall Number Length 6400 1/4" 1/2" 1 1/4" 6400x8 8mm 1/2" 1 1/4" 6401 5/16" 1/2" 1 1/4" 6402 3/8" 1/2" 1 1/4" 6403 1/4" 3/4" 1 1/4" 6404 5/16" 3/4" 1 1/4" 6405 3/8" 3/4" 1 1/4" 6406 1/2" 3/4" 1 1/4"
STEEL ROUTER COLLETSReducer Bushings
PART #6406
Page 157Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
ClibPDF - www.fastio.comPage 158
WHITESIDE MACHINE COMPANY
W300 - SHIM WASHER KITUse these shim washers to fi ne adjust the spacing on any
arbor or assembly with a 5/16" diameter arbor (Slot Cutters, Stile & Rail, Window Sash, Tongue & Groove). Washers are 5/16" I.D. x 1/2" O.D. Includes three each of the following thicknesses: .004, .006, .008, .010, .012.
Part Shank Arbor Arbor Overall Number Diameter Diameter Length Length A200 1/4" 5/16" 7/8" 2 3/8" A205 3/8" 5/16" 7/8" 2 1/2" A210 1/2" 5/16" 7/8" 2 5/8" A220 1/2" 5/16" 7/8" 4" A250 1/4" 5/16" 1 3/16" 2 3/4" A260 1/2" 5/16" 1 3/16" 2 7/8" A300 1/4" 5/16" 1 7/16" 3" A310 1/2" 5/16" 1 7/16" 3 3/16" A375 1/2" 5/16" 1 3/4" 3 3/8" A550 1/2" 1/2" 1 7/8" 3 7/8" A552 1/2" 1/2" 2 1/8" 4 1/8" A560 1/2" 1/2" 2 3/8" 4 3/8"
Arbors include nut and washer.
ARBORS
ARBOR LENGTH
ACCESSORIES
QUICK CHANGE CHUCKSSwap router bits quickly and easily.
Cam-lock design clamps and loosens with a partial turn using a hex key wrench. Much simpler than the original two wrench method. Holds 1/2" shank bits. Order #6400 Router Collet for 1/4" shanks. Replace the factory collet with a Quick Change.
9750 - EXTENSION ADAPTERFor CNC Carving Machines
Used for light routing and veining on CNC carving machines. Allows deeper reach. Adapter is 1/2" shank. Accepts 1/4" shank bits only. Order Part #9750.
PART #A200
PART #9700
PART #9750
9600 - SQUARE CORNER CHISEL
Use this tool to square up the round corners left behind when routing hinge mortises. Hold unit in mortise corner and strike with hammer. Our chisel features a sharp 3/8" square hardened steel cutting blade. Made in USA by Whiteside Machine Company.
Our Square Gauge Blocks are a quick way to make many easy, accurate set-ups. A great way to make exact depth movements on plunge routers. On table routers, they're perfect for setting distances from the fence to the cutter, or for checking the bit height above the table. Supplied in 1/8", 3/16", 1/4", 3/8", and 1/2" squares. Blocks can be "stacked" to cover a wider range of sizes. A very helpful tool!
Part# Description 9800 5 pc. Set - 2 1/2" Long 9810 5 pc. Set - 4" Long
BRASS SET-UP GAUGE BLOCKS
9500 - SOLID BRASS INLAY KIT
Whiteside's brass inlay kit allows you to make perfect fi tting inlays for decoration or repairs. Simply cut your template from 1/4" thick material and trace it with your router to cut both the cavity in your workpiece and the matching inlay to be inserted. Instructions are included. Our kit includes a special centering pin to insure exact alignment with router spindle. Also includes a 1/8" Solid Carbide Spiral Router Bit (Part# RD1600).
9510 - BASE PLATE REDUCERS - SOLID BRASS
These solid brass inserts fi t into your router base plate to reduce the gap around the router bit. Not only is this safer, but it also reduces tearout and helps support smaller workpieces. Supplied in a set with openings of 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", and 1", plus retaining nut. Openings are slightly oversize for tool clearance. Fits any router with a standard 1 3/16" diameter recessed hole for template guides.
Part Description Number 9700 All 1/2" Porter-Cable (except #100) 9710 All 1/2" Bosch 9720 Dewalt 625/Elu 1/2"/Festool/Freud 9730 Dewalt 616, 618, 621
RetainingNut
Page 159Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
WHITESIDE MACHINE COMPANY
Part Thread Thread Hex Key Number Size Length Size 34825S 3-48 1/4" 5/64" 54025S 5-40 1/4" 3/32" 103238S 10-32 3/8" 5/32"Add BLK to part number for 100 pcs.
Socket Head Cap Screws - 10 pc. pack
SPARE PARTS LISTING
Hex Nuts - 10 pc. pack Part Thread Hex Number Size Width Size 1032N 10-32 1/4" 3/8" 31224N 5/16-24 1/4" 1/2" 5020N 1/2-20 7/16" 3/4"
Flat Washers - 10 pc. pack Part Inside Outside Number Diameter Diameter Thickness 31250W 5/16" 1/2" 1/16" 5088W 1/2" 7/8" 5/64"
Replacement Parts By Tool NumberReplacement Bearing sizes are listed in the catalog with each
tool. Most tools with bearing pilots on the end require only the 54025S Screw. Exceptions: 34825S Screw: 2400,2401,2404A 103238S Screw 2013-2016, 2410, 2560, 2570, 2575, 2580, 2900-2908, 3390 1032N Nut RFT5125, RFTD5125, RFT5200 RFTD5200, UDFT5152
BEARINGS
TOLL FREE 1-800-225-3982 • FAX: 1-828-459-1252
HEX KEY WRENCHES
Part Number Size Application HK-1/16 1/16" Bearing Lock Collars HK-5/64 5/64" 1/8" I.D. Bearings (3-48 Screw) * HK-3/32 3/32" 3/16" I.D. Bearings (5-40 Screw) HK-5/32 5/32" 1/4" I.D. Bearings (10-32 Screw)* Standard Size for Most Bits
Use this kit to vary the horizontal cutting depth of router bits with bearing pilots.
Great for stepping in to f inish depth by controlled increments.
Contains B2 (3/8"), B3 (1/2"), B7 (5/8"), B8 (3/4") Bearings and 3/32" Hex Key Wrench
BB501 - 5 PIECE BEARING CONVERSION KIT
BB600 - GENERAL BEARING REPAIR KITThis handy kit inludes spare bearings, screws, and wrench
to replace bearings on most bits.Includes fi ve B3 (1/2 x 3/16) and two B2 (3/8 x 3/16)
bearings, ten 54025S Screws, and a 3/32 Hex Key Wrench.
BB701 - ACCESSORY KITGreat for replacement bearings and screws - Plus this generous
bearing assortment allows you to vary your cutting depths and change your profi les. Also contains lock collars and bearings for adding bearing guides to the shanks of your standard bits for following templates.
Contains: 12 bearings — four B3 (1/2 x 3/16), one each of B2 (3/8 x 3/16), B7 (5/8 x 3/16), B8 (3/4 x 3/16), B9 (1/2x 1/4), B6 (5/8 x 1/4), B4 (3/4 x 1/4), B5 (7/8 x 5/16) and B11 (1 1/8 x 1/2);two each 1/4" lock collars (LC-1/4) and 1/2" lock collars (LC-1/2);one each 1/16, 5/64, 3/32 and 5/32 Hex Key wrenches; plus ten 54025S bearing screws.
Part Outside Inside Number Diameter Diameter Application B1A 1/4" 1/8" B1 3/8" 1/8" B2 3/8" 3/16" B3 1/2" 3/16" Standard B3BLK 1/2" 3/16" 100 pcs. bulk B3S 1/2" 3/16" Non-Mar Nylon Sleeve B3SQ 1/2" 3/16" Euro-Square (Pg. 15) B3T 1/2" 3/16" Tefl on® Shields B3U .490" 3/16" for resharps (undersize) B4 3/4" 1/4" B5 7/8" 5/16" B6 5/8" 1/4" B7 5/8" 3/16" B8 3/4" 3/16" B8SQ 3/4" 3/16" Euro-Square (Pg. 15) B9 1/2" 1/4" B9U .490" 1/4" for resharps (undersize) B11 1 1/8" 1/2" B12 7/8" 3/8" B14 11/16" 3/16" B15 13/16" 3/16" B16 1 1/4" 1/2" B17 1 3/8" 1/2" B18 1 1/2" 1/2" B19 3/4" 1/2" B20 3/4" 5/16" B21 7/8" 1/4" B24 1 7/8" 1/2" B25 1 1/8" 5/16" B26 1 3/8" 5/16" B27 5/8" 5/16" B28 7/8" 3/16" B29 1" 3/16" BB300 7/8" x 10° 3/16" Non-Mar Nylon Sleeve
BALL BEARINGS
Part Shank Outside Number Diameter Diameter LC-1/4 1/4" 7/16" LC-1/2 1/2" 11/16"Uses part # HK-1/16 Hex Key Wrench#LCS-Replacement Set Screw for Lock Collars
BEARING LOCK COLLARSRetaining Collars used when bearings are added to the
shanks of router bits for following templates.
PART #B5
Page 160
UD4125STANDARD SPIRAL BITS UD5150
RU/RD1600 $19.50 UP/DOWN CUT (2+2) I'"
RU/RD1700 $20.40 UD2102 $34.00RU/RD1800 $19.50 UD4102M $58.00
RU/RD1900 $20.00 UD4122 $58.00 SC29 $10.50
RU/RD2075 $18.76 UD5122 $75.00 SC29-BLK (100 pcs.) $7.24ea
RU/RD2100 $19.50 UD5122M $80.00 SC29A $17.00
RU/RD3100 $32.00 UD5152 $82.00 SC30 $11.50
RU/RD4075 $30.00 UD5162 $82.00 SC31 $12.75
RU/RD4100 $33.00 UD5202 $90.00 SC32 $12.50
RU/RD4125 $35.00 UD6152 $168.00 FLAT BOTTOM VEINING
RU/RD4675 $26.50 UD7202 $196.00 SC062 $15.00
RU/RD4700 $28.50 UP/DOWN FLUSH TRIM SC33 $14.25
RU/RD4800 $69.00 UDFT5152 $118.00 SC156 $14.60
RU/RD4850 $52.50 O-FLUTESRIRALBITS SC34 $15.20
RU/RD4875 $49.50 RU/RD2075A $22.50 SC35 $16.75
RU/RD4900 $52.50. ROUND BOTTOM VEINING
RU/RD4950 $52.00 O-FLUTE STRAIGHT BITS SC39 $17.40
RU/RD5100 $47.00 SA1600 $20.65 SC40 $16.90
RU/RD5125 $49.50 SA 1700 $25.00 SC41 $16.62
RU/RD5150 $53.00 SA1800 $20.65 CARVING UNER
RU/RD5200 $65.00 SA1900 $25.00 SC50 $25.00
RU/RD6150 $115.00 SA2075 $20.65 SC FIBERGLASS BIT
RU/RD6200 $124.00 SA2100 $26.00 SC90 $21.00
RU/RD7150 $116.00 SA4100 $42.00 SC90V $22.00
RU/RD7200 $125.00 SOUD CARBIDE 1 FLUTE . .
RU/RD7300 $170.00 SC062 $15.00 CNCROUTER BITS
RU/RD7306 $185.00 SC01 $21.00 C1052 $19.46
CHIPBREAKER SPIRAL BITS SCOlA $21.00 C1055 $24.00
RU/RD5125CB $62.00 SC02 $14.00 C1067 $20.58
RU/RD5150CB $65.00 SC03 $15.40 C1069 $22.64
RU/RD5200CB $77.00 SC04 $15.30 C1072 $32.00
FLUSH TRIM SPIRAL BITS SC05 $16.90 C6310 $29.50 I"
RFT/RFTD1600 $36.00 SC06 $18.12 C6320 $36.00RFT/RFTD2100 $40.00 SC07 $20.40 C7512 $29.50
RFT/RFTD5125 $79.00 SC08 $24.30 C7515 $32.00
RFT/RFTD5200 $94.00 SC17 $32.00 C7520 $38.00
UDFT5152 $118.00 SOliD CARBIDE 2 FLUTE C7520F $48.00
LEFT HAND SPIRAL BITS SC33 $14.25 C7520V $51.00
LU/LD1600 $24.00 SC09 $14.20 C7525 $42.00
LU/LD1800 $24.00 SC09A $15.00 C7525F $52.00
LU/LD2100 $22.50 SC156 $14.60 C8820V $42.00
LU/LD3100 $44.00 SC10 $15.03 C1108 $35.00
LU/LD4100 $44.00 SC10A $15.75 C1109 $44.00
LU/LD5125 $56.00 SC34 $15.20 LEFT HAND STRAIGHT BITS
W/LD5200 $80.00 SC11 $15.40 1014LH $24.56
LU/LD6150 $169.00 SC11A $16.20 1062LH $30.00
LU/LD6200 $218.00 SC12 $16.80 1066LH $32.50
LU/LD7150 $165.00 SC13 $17.49 1069LH $38.50
LU/LD7200 $175.00 SC3S $16.75 1072LH $46.00
SC14 $18.00 1085LH $38.00
ROUGHING SPIRAL BITS SC15 $21.77 1105LH $44.00
RU4000H $51.00 SC16 $25.74 1126LH $48.00
RU/RD4100H $55.00 SC17 $32.00 1128LH $50.00
RU/RD4125H $56.00 SC18 $32.42 1/4" SHANK STRAIGHT BITS
RU/RD5162H $110.00 SC19 $34.00 1004 $11.95
RU/RD5218H $142.00 SC19A $36.00 1005 $12.32RU/RD6200H $156.00 SC218 $25.00 1007 $12.60
RU/RD7200H $184.00 SC235 $25.00 1008 $13.35
RU/RD7325H $248.00 SC20 $26.50 1012 $14.20
THREE FLUTE SPIRAL BITS SC21 $28.50 1013 $14.00
RU/RD4125T $38.00 SC22 $36.00 1014 $14.50
RU/RD5125T $52.00 SC23 $42.00 1016 $15.50
RU/RD5200T $68.00 SC24 $45.00 1016-01 $16.40 I'RU/RD7200T $140.00 SC25 $45.00 1018 $16.40
SWW SPIRAL BITS SC26 $47.00 1019 $15.60
RU/RD4100S $42.00 SC27 $49.00 1020 $16.12
RU/RD5100S $54.00 LAMINATE TRIM 1020x8 $18.99
RU/RD5150S $60.00 SC28B $9.50 1021 $15.60
UP/DOWN CUT (1+1) SC28B-BLK (100 pcs.) $6.74ea 1022 $16.40
UD2100 $36.00 SC28 $10.50 1 2 1 96Page 161Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
I I
1024 $17.90 1093F $33.32 13-812 $24.201024A $18.00 1094 $26.74 13-875 $24.20
~ 1025 $16.00 1095 $36.50 13-937 $26.20
1026 $17.00 1096 $33.24 13-1000 $26.201027 $18.00 1304 $23.25 13-1125 $26.201027A $18.00 1097 $32.00 13-1250 $26.201028 $17.96 1098 $37.50 13-1250A $26.201029 $20.56 1099 $39.60 HEUX MORTISE ARBORS
1029A $20.56 1100 $57.00 HMA-1/4 $5.00
1030 $18.76 1101 $60.90 HMA-1/2 $5.001031 $20.90 DADO BITS HMA-1/4A $5.00
1033 $23.50 SC13 $17.49 HMA-1/2A $5.00
1303 $26.85 1024A $18.00. .3/8" SHANK STRAIGHT BITS 1027 A $18.00 BOWL & TRAY BITS
1035 $14.95 1029A $20.56 1370 $2400
1036 $17.60 SC218 $25.00 1372 $25'00
1039 $17.26 SC235 $25.00 1372B $29:50
1040 $18.40 1065A $15.90 1374 $25001041 $19.06 1075A $19.56 1376 $29:001043 $18.30 1083A $19.95 1376B $36.00
1045 $24.00 TEMPLATE BITS ROUND NOSE (CORE BOX)
3000A $22.50 SC39 $17.40
1/2" SHANK STRAIGHT BITS 3000 $21.50 SC40 $16 90
3002 $23.50$16'
621049 $14.95 3004 $2420 SC41 .
1050 $16.38 3006 $23'50 1403 $19.471051 $14.50 K41 $30'00 1404 $23.46
1052 $15.25 K43 $32'00 1405 $24.27
1054 $16.25 3008 $29'50 1406 $24.741055 $19.50 3010 $23'50 1407 $26.961055A $24.82 3012 $28'50 1408 $28.44
1058 $17.70 3014 $29'95 1410 $31.001059 $17.70 3015 $38'00 1411 $35.501060 $18.24 3016 $38'00 1412 $45.00
~ 1061 $15.65 3018 $42'50 1413 $46.00
1062 $17.26 3019 $55'00 1414 $50.001063 $18.96 3020 $32'00 1415 $65.001064 $17.40 3021 $34'00 1416 $94.001065 $17.62 3022 $37'50 1417 $99.001065L $18.72 . 1420 $82.00
1065A $16.40 3023 $46.00 ROUND NOSE W/BEARING
1066 $16.40 1404B $29.80
1067 $16.90 STAGGERTOOTH BITS 1405B $29.80
1067F $24.65 1200 $18.00 1406B $29.801069 $18.20 1201 $20.20 HALF ROUND (BULL NOSE)
1069DS $21.84 1202 $20.20 1425 $30.00
1070 $20.54 1203 $23.50 1426 $30.001071 $25.08 1205 $56.00 1427 $36.001072 $25.68 UP/DOWN STAGGERTOOTH BITS 1428 $46.00
1073 $33.32 1250 $36.00 1429 $30.001073-01 $36.00 1252 $39.00 1430 $30.001074 $19.95 1260 $52.00 1431 $35.001075 $18.60 1270 $52.00 1432 $45.001075A $19.56 MORTISE BITS 1432A $56.00
1076 $17.80 1300 $16.45 1433 $68.001076F $26.40 1301 $18.36 1433A $75.001077 $18.60 1302 $19.06 1434 $75.001078 $19.95 1302A $19.40 1434A $90.00
1079 $31.28 1303 $26.85 1435 $90.001080 $22.32 1304 $23.25 1436 $140.001082 $19.95 SCREWTYPEMORTISE PLUNGE CUT HAND GRIP
1083 $20.90 13-500 $23.05 1440 $52.001083A $19.95 13-515 $23.05 OVAL EDGE
1302A $19.40 13-531 $23.05 1474 $32.50
1084 $19.40 13-562 $23.05 1476 $42.50~ 1085 $19.95 13-625 $23.05 1478 $50.00
1085F $28.40 13-640 $23.05 1480 $62.001086 $22.60 13-656 $24.201087 $31.20 13-687 $24.20 90° VEE GROOVE
1088 $21.40 13-719 $24.20 1500 $15201090 $22.50 13-750 $24.20 1501 $17941091 $22.50 13-765 $24.20 1502 $21'001093 $24.92 13-781 $24.20 .
Page 162
1503 $22.00 2000 $23.50 CHAMFER/EDGE BEVEL
1504 $41.40 2001 $23.50 2298 $19.501505 $52.90 2002 $26.00 2300 $20.40 I'1507 $ 73.60 2003 $26.00 2300A $18.50
1508 $65.00 2004 $32.00 2301 $21.20600 VEE GROOVE 2005 $24.50 2302 $26.50
1540 $15.20 2005C $22.50 2305 $26.501541 $18.20 2006 $23.50 2306 $41.251550 $22.00 2007 $26.00 2307 $29.501560 $23.00 2008 $26.00 2308 $34.00
POINT CUT ROUNDOVER 2008A $35.00 2309 $31.00
1570 $21.00 2009 $32.00 2310 $78.001572 $22.50 2009A $52.00 2325 $28.00
1574 $28.50 2009B $42.00 ..
1580 $28.50 2010 $57.00 FLUSH TRIM TWO FLUTE
PANEL BITS 2011 $98.00 2400 $1690
1700 $11.96 2012 $109.72 2401 $16.081701 $16.00 2013 $142.00 2402 $16.901702 $16.00 2014 $148.00 2403 $16'081704 $23.20 2015 $162.00 2404A $18:001705 $23.20 2016 $162.00 2405 $17601706 $26.00 BEADING BITS 2406 $16. %
STAGGERTOOTH PANEL 2100A $25.00 2407 $2120
1726 $40.00 2100C $25.00 2408 $26.80
COVE BITS 2100D $27.00 2410 $24'80
1800A $26.00 2100 $25.00 2457 $42.50
1800 $26.00 2101 $25.40 2458 $48.001801 $28.50 2102 $28.00 FLUSH TRIM - DOWNSHEAR .
1802 $32.00 2103 $28.00 2602 $21 001803 $26.00 2104 $34.00 2605 $21'501804 $28.50 2105 $27.00 FLUSH TRIM V-GROOVE .
1805 $32.00 2105C $24.50 2425 $22 20
1806 $51.00 2106 $25.40 2426 $22201807 $58.00 2107 $28.00 OVERHANG TRIM BITS . I
1810 $90.00 2108 $28.00 2468 $19.50: . 2109 $34.00 2470 $1950
RABBET BITS 2 L 1 T 12 B 'r AD "'.T. G S 'r ~ $59.00 FLUSH TRIM THREE FLUTE.
1900 $24.50 MU 6.- ~ 6.J.. ~6. oJ 2500 $23.00
1951 $27.00 2040B $38.00 2501 $21.50
1901 $24.50 2042B $42.75 2502 $23.501954 $26.50 2044B $45.00 2503 $22.00
1959 $52.00 PLUNGE ROUNDOVER BITS 2504 $28.32
SWT & RABBET BITS 2050 $22.00 2505 $36.00
1904 $24.00 2051 $30.00 2554 $49.701906 $24.00 2052 $34.00 2555 $57.001908 $21.00 2055 $34.00 DOWNSHEAR FLUSH TRIM
1910 $21.00 2056 $37.50 2560 $26.001912 $22.50 2057 $42.75 2570 $30.001914 $22.50 2058 $44.00 2575 $34.001916 $25.00 2060 $52.00 2580 $39.601918 $25.00 2062 $66.00 2602 $21.001920 $27.50 2064 $72.00 2605 $21.501922 $27.50 2066 $79.001924 $31 00 ROUNDOVER & EDGE TRIM
BISCUIT JOINING KIT . 2068 $54.00 LAMINATE TRIM BITS
1940 $32 50 2070 $ 74.00 2401 $15.601945 $32.50 2072 $65.00 2298 $19.50
RABBET SETS . 2074 $84.00 2300A $18.50
1952 $5800 2076 $72.00 2301 $21.201955 $58:00 2078 $88.00 SC28B $9.50
1960 SC29 $10.50
.RO "~TTO OV 'rD COMBINATION FLUSH/BEVEL
. DOUBLE t.lJ , LA 2800 $16.60
ROUNDOVER BITS (SMALL PILOT) 2160 $56.00 2801 $16.60
1978 $25.00 2162 $56.00 EURO-SQUARE TRIMMERS
1980 $24.00 2164 $56.00 2640 $22.50 !
1982 $24.50 ROMANOGEE 2650 $29.90
1984 $27.00 2200 $34.50 2660 $29.90ROUNDOVER BITS 2201 $37.50 EURO-SQUARE BEARINGS
2000A $23.00 2202 $34.50 B3SQ $6.50
2000B $24.50 2203 $37.50 B8SQ $6.50
2000C $22.50 2210 $56.00
2000D 25.00 Page 163Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
3194SOLID SURFACE BITS 3196 $ 76.00--- 2006N $27.00 MULTI-BEADING $97.50
2009N $35.50 3200
2010N $60.50 3202 $46.74 DRAWER GLUE JOINTS
2030 $44.00 DOUBLE ROUND 3346 $34.00
2034 $82.00 3205 $38.80 3347 $36.002036 $112.00 3206 $42.00 3350 $53.122900-2908 $29.94 3207 $38.80 3352 $53.122929 $94.00 3208 $42.00 STANDARD GLUE JOINT
2930 $109.00 3354 $62.002944 $65.00 COVE&BEAD 45°WCKMITER
2945 $54.00 3209 $39.00 3360 $122.003210 $39.00 3362 $90.00
TEMPLATE BITS 3211 $39.00 WEDGE TONGUE & GROOVE
3000A $22.50 3212 $39.00 3370 $120.003000 $21.50 3282 $62.00 3370A-3370B $65.003002 $23.50 OGEE FILLET STRAIGHT T & G
3004 $24.20 3214 $37.80 3373 $120.003006 $23.50 3216 $37.80 3373A-3373B $65.00K41 $30.00 3218 $44.10
K43 $32.00 OGEE VEE PANEL T & G
3008 $29.50 3220 $37.94 3374 $145.003010 $23.50 3222 $37.94 3374A-3374B $77.503012 $28.50 3224 $41.00 T & G ASSEMBLY
3014 $29.95 3226 $41.00 3375 $56.003015 $38.00 3228 $48.00 3375G $25.003016 $38.00 CLASSICAL PATTERN FINE FINGER JOINT
3018 $42.50 3230 $39.60 3390 $116.003019 $55.00 3232 $39.60 MULTI SIDE BITS
3020 $32.00 3234 $43.70 3506 $47.003021 $34.00 3236 $43.70 3508 $47.00
~ 3022 $37.50 EDGE BEADING 3516 $47.00
3023 $46.00 3240 $29.80TEMPLATE BITS 3242 $29.80
WITH OVERSIZE BEARINGS 3244 $34 00 PLUNGE ROUNDOVER. 2051 $30.003025 $24.00 3246 $34.00 2055 $34 003028 $23.50 3248 $37.00 2057 $42 753032 $25.00 3250 $37.00 PLUNGE OGEE .
KEYHOLE BITS 3252 $39.00 3602 $24 00
3050 $14.00 3254 $39.00 3604 $26'003051 $16.00 3256 $41.00 3606 $26'703052 $18.00 3258 $41.00 3608 $34'003053 $18.80 3260 $51.00 CLASSIC ROUND BOTTOM .
T-SWTCUTTERS 3262 $56.00
3070 $55.00 FRENCH TRADITIONAL 3720 $29.50
3075 $62.00 3270 $48.86 3725 $32.00SWT & UNDERCUT BITS 3272 $48.86 3730 $34.00
3094 $18 90 3735 $34.00. 3740 $40.003094B $26.40 FRENCH PROVINCIAL 3750 $50 00
3098 $21.40$ 0 .
3098B $28 50 3280 88. 0 CLASSICAL FLAT BOTTOM
3110 $24.50 3282 $62.00 3770 $34.00. TABLE EDGE 3780 $50 00
3110B $31.75 3290 $38.00 MODEL TRAIN TRACK BITS.
3292 $38.00 3900 $28.00CLASSICAL COVE 3294 $ 78.00 3902 $49.50
3160 $35.50 3228 $48.00 3910 $28.003162 $40.00 32% $78.00 3915 $44.00
3164 $35.50 3298 $78.003166 $40.00 3300 $ 78.00 MDF DOOR BITS
WAVY EDGE 3302 $ 78.00 5610 $46 00
3170 $36.00 5620 $50'003172 $36.00 HANDRAIL 5630 $50'00
~ RADIUS FLUTE CUTTER 3304 $82.00 5645 $50:00
3180 $38.00 3305 $91.00 5710 $72 003181 $38.00 SPECIALTY MOLDING 5720 $72'00
3182 $38.00 3320 $4276 5725 $72.003183 $38.00
33 $ . .FULL BEAD 24 50.00 ",
3190 $38.00 3326 $50.00 MINI STILE & RAIL SETS
3192 $40.00 3330 $55.00 5740-5742 $140.00Page 164
I
D75-25 $21.70 6704A $19.20
STILE & RAIL SETS D8-250 $22.20 6704C $19.90
600l-6006 $128.00 D8-250x8 $28.00 6705A $18.86
INDIVIDUAL CUTTERS D8-312 $20.40 6705B $27.72
600lA-6006B $ 70.00 D8-312x8 $24.00 6708A $18.86
600lG $20.00 D8-375 $18.20 6709A $18.86
PLYWOOD:sTILE&RAIL D8-375x8 $21.00 6709C $19.90
6000X (KIt) $45.00 D8-437 $21.40 6710A $18.86
600lX-6002X $140.00 D8-437x8 $25.80 6710B $28.50
D8-500 $20.40 6712A $23.40
MINI RAISED PANEL BITS D8-500x8 $24.70 SLOT CUTTER ARBORS
5750-5751 $52.00 D8-687 $24.70 AZOOB $8.84
RAISED PANEL BITS D8-812 $26.50 A205B $10.84
5950-5954 $75.00 D9-312 $22.00 AZ10B $8.84
LARGE RAISED PANEL- 09-372 $19.95 A220B $16.34
TWO WING 09-373 $21.40 DRAWER SLOT CUTTERS
5900A-5900H $108.00 09-375 $21.40 6800 $25.00THREE WING 09-375LH $23.50 680l $30.00
6000A-6000H $126.00 09-376 $22.20 6804 $25.00LARGE RAISED PANELS WITH 09-376LH $24.70 6805 $30.00
BACK CUTTER 09-390 $21.40 ARBORS FOR
5920B-5920E $128.00 09-390LH $23.50 DRAWER SWT CUTTERS
010-50 $19.95 6890 $8.00010-50x8 $25.00 6891 $8.00010-55 $23.25 6892 $8.00014-375 $21.00 6896 $20.00014-50 $19.40 SOUD CARBIDE KNIVES
014-51 $20.40 6902 $46.00014-51x8 $24.40 6904 $66.00
DOOR EDGE BITS 014-55 $23.50 6906 $92.00
60l0 $65.00 014-531 $24.00 6910 $59.0060l5 $55.00 014-75 $22.60 6912 $76.0060l6 $65.62 014-100 $36.50 6914 $112.003290 $38.00 018-50 $19.95 ..3292 $38.00 D18-50x8 $24.90 DOWEL DRILLS.
6020 $46.00 1020 $16.12 BRAD POINT - iNCH SIZES
6021 $46.00 1020x8 $18.99 S7MMOAL C 1:
6022 $46.00 1064A $17.40 OB187-57(LH). $7.336023 $46.00 KELLER BITS OB218-57(LH) $7.33
DRAWER PULL K31 $35.00 OB250-57
( LH ) $7.336024 $54.00 K33 $36.00
6026 $59.50 K35 $4600 70 MM OAL-C.T.
6032 $34.50 K41 $ 30'00 OB187-70(LH) $7.92. DB218-70(LH) $7.92
WINDOWSILL EDGE K43 $32.00 OB250-70(LH) $7.92
6045 $49.00 30l5 $38.00 OB375-70(LH) $8.836046 $59.50 3032 $25.00 OB437-70(LH) $9.83. . , DB500-70(LH) $9.83
WINDOW SASH CNC SPOILBOARD SURFACING BRAD POINT - METRIC SIZES
6050 $102.00 SB25-2 $304.00 S7 MM OAL-C. T.
AKEDADOVETAILBITS SB40-2 $316.00 OB4-57(LH) $7.33
DA7-438 $28.16 SB40-3 $340.00 OB5-57(LH) $7.33DA9-438 $28.16 SBU25-2 $340.00 OB6-57(LH) $7.33OAll-438 $28.16 SBU40-3 $390.00 OB7-57(LH) $7.50OA14-438 $28.16 SB-INSERT (10 pcs.) $34.00 OB8-57(LH) $8.00OA20-438 $28.16 SB-SCREW $3.40 OB9-57(LH) $8.00
1020AKS $18.41 SB-WRENCH $8.00 OB10-57(LH) $8.00
1020AOS $18.41 ROUTER COLLETS OBll-57(LH) $9.08
1020AUS $18.41 6400 $12.50 OB12-57(LH) $8.75
1020ABJ $22.10 6400x8 $12.50 OB13-57(LH) $9.08
0102A (SET) $197.64 640l $12.50 DB14-57(LH) $9.67
DOVETAIL SETS 6402 $12.50 OB15-57(LH) $9.38
0101 (INCRA-1/4 shk) $98.00 6403 $18.00 OB16-57(LH) $9.67605 (INCRA-1/2shk) $110.00 6404 $18.00 70MMOAL-C.T.
m08 (LEIGH - 8mm shk) $110.00 6405 $18.00 OB4- 70(LH) $ 7 . 92
0116 (LEIGH-16" Ji -8mm shk) $98.00 6406 $15.00 OB5- 70(LH) $ 7.92
SWTTINGCUTTERS OB6-70(LH) $7.92
DOVETAIL BITS 6700A $15.00 OB7-70(LH) $8.08
07-531 $22.00 6700B $22.44 OB8-70(LH) $8.8307-625 $26.50 670lA $16.95 OB9-70(LH) $9.00
07-750 $30.00 6702A $16.95 OB10-70(LH) $9.00
07-875 $34.20 6703A $16.75 OBll-70(LH) $9.83
D7-875LH $39.60 6703B $25.14 OB12-70 LH $9.83
Page 165Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
DB13-70(LH) $9.83 DH30-57(LH) $22.92 B15 $9.50DB14-70(LH) $10.63 DH35-57(LH) $23.28 B16 $16.00
" , DB15-70(LH) $10.63 70 MMOAL B17 $16.00
DB16-70(LH) $10.63 DH15-70(LH) $22.13 B18 $16.00BRAD POINT DH20-70(LH) $22.58 B19 $12.50
57 MM OAL- SOUD CARBIDE DH25-70(LH) $23.12 B20 $10.00
DB3-57(LH)SC $16.25 DH30-70(LH) $23.57 B21 $14.00DB4-57(LH)SC $15.05 DH35-70(LH) $23.90 B24 $19.00DB5-57(LH)SC $15.16 BORING BITS B25 $15.00
DB6-57(LH)SC $18.08 6100 $102.00 B26 $15.00DB8-57(LH)SC $25.09 6140 $48.00 B27 $9.00
70 MM OAL- SOLID CARBIDE FACE FRAME C'BORES B28 $11.00
DB3-70(LH)SC $17.58 FF301 $34.00 B29 $11.00DB4-70(LH)SC $16.24 FF301SP $40.80 BB300 $18.90
DB5-70(LH)SC $15.95 FF302 $54.00 BEARINGWCK COLLARS
DB6-70(LH)SC $19.64 FF303 $5.80 LC-1/4 $3.25DB8-70(LH)SC $28.98 FF304 (Set Screw) $.28 LC-1/2 $3.25
THRU V-POINT -INCH SIZES BEARING KITS
57MMOAL-C.T.. BB501 $15.00DT250-57(LH) $20.75 BRASS INLAY KIT BB600 $21.00
70MMOAL-C.T. 9500 $39.00 BB701 $48.00
DT187 70(LH) $21 60 BASE PLATE REDUCERS HEX KEY WRENCHES
- . 9510 $42.00DT218-70(LH) $21.60 SQUARE CORNER CHISEL HK-1/16 $1.00
DT250-70(LH) $21.88 9600 $2700 HK-5/64 $1.00DT375-70(LH) $31.83 QUICK CHANGE CHUCK' HK-3/32 $1.00
DT437-70(LH) $35.97 9700 $6950 HK-5/32 $1.00DT500-70(LH) $38.05 9710 $76'00 SPARE PARTS:
THRU V-POINT - METRIC SIZES 9720 $ 76' 00 SOCKET HEAD SCREWS
57MMOAL-C.T. 9730 $76'00 34825S (10 pcs.) $4.00DT4-57(LH) $14.23 EXTENSION ADAPTER . 34825SBLK (100 pcs.) $24.00DT5-57(LH) $14.23 9750 $52.00 54025S (10 pcs.) $4.00DT6-57(LH) $14.43 SET UP GAUGE BWCKS 54025SBLK (100 pcs.) $24.00DT7-57(LH) $16.30 9800 $1100 103238S (10 pcs.) $4.00
" , DT8-57(LH) $15.33 9810 $16'00 103238SBLK (100 pcs.) $24.00DT9-57(LH) $21.15 ARBORS . HEX NUTS (10 PC. PACK)
DT10-57(LH) $18.38 A200 $450 1032N $5.00DTll-57(LH) $23.90 AZ05 $7'00 31224N $5.00DT12-57(LH) $25.28 AZ10 $4'50 5020N $6.00DT13-57(LH) $28.07 AZ20 $12'00 FLAT WASHERS (10 PACK)
DT14-57(LH) $30.82 A250 $6'00 31250W $8.00
DT15-57(LH) $33.58 AZ60 $6'00 5088W $10.0070MMOAL-C.T. A300 $6'50
DT4-70(LH) $15.00 A310 $6'00 RAISED PANEL SETS- WOOD BOX
DT5-70(LH) $15.00A37S $9 '
00 $DT6-70(LH) $1668 . 100 240.00DT7 - 70(LH) $18' 77 A550 $12.00 101 $240.00
DT8-70(LH) $17'63 A552 $14.00 120 $245.00DT9-70(LH) $24'03 A560 $16.00 121 $245.00
DT10-70(LH) $20'97 SHIM WASHER KIT 200 $290.00
DTll-70(LH) $27:12 W300 $12.00 201 $290.00DT12-70(LH) $28.63 220 $295.00DT13-70(LH) $31.72 BALL BEARINGS 221 $295.00
DT14-70(LH) $34.78 B1A $6.00DT15-70(LH) $37.87 B1 $5.00 ROUTERBITSETS-PLASllCCASE
THRU V-POINT B2 $4.50 401 $110.00
57 MM OAL- SOUD CARBIDE B3 $4.50 402 $110.00
DT3-57(LH)SC $17.10 B3-BLK (100 pcs.) $3.25ea 501 $110.00DT4-57(LH)SC $17.20 B3S $8.25 502 $110.00DT5-57(LH)SC $15.99 B3SQ $6.50 600 $210.00
DT6-57(LH)SC $18.24 B3T $5.50 605 $110.00DT8-57(LH)SC $25.09 B3U $5.50 I, .
70 MM OAL- SOUD CARBIDE B4 $4.00
DT3-70(LH)SC $20.14 B5 $4.00 CUSTOM BITS
DT4-70(LH)SC $17.56 B6 $4.00 Please copy and fill out the form on
~ DT5-70(LH)SC $16.99 B7 $4.40 the back of this price list.
DT6-70(LH)SC $20.36 B8 $6.00DT8-70(LH)SC $28.98 B8SQ $6.50
HINGE BORING BITS B9 $5.00
57MMOAL B9U $7.50
DH15-57(LH) $21.50 B11 $5.00
DH20-57(LH) $21.95 B12 $8.00DH25-57(LH) $22.48 B14 $8.50
Page 166
Fuller
Countersinks · Counterbores · Tapered Drills · Plug Cutters · Step Drills · Stop Collars
Decimal Equivalency Chart (Part 1) Inch Dec-
imal Wire mm Tap Sizes Inch Dec-
imal Wire mm Tap Sizes Inch Dec-
imal Wire mm Tap Sizes
.0059 97 .15 .0390 61 .1100 35 .0063 96 .16 .0394 1. .1102 2.8 .0067 95 .17 .0400 60 .1110 34 .0071 94 .18 .0410 59 .1130 33 #6-40 .0075 93 .19 .0413 1.05 .1142 2.9 .0079 92 .20 .0420 58 .1160 32 .0083 91 .21 .0430 57 .1181 3. .0087 90 .22 .0433 1.1 .1200 31 .0091 89 .23 .0453 1.15 .1220 3.1 .0094 .24 .0465 56 1/8 .1250 5/32-32NS .0095 88 3/64 .0469 #0-80 .1260 3.2 .0098 .25 .0472 1.2 .1280 3.25 .0100 87 .0492 1.25 .1285 30 5/32-36NS .0102 .26 .0512 1.3 .1299 3.3 .0105 86 .0520 55 .1339 3.4 .0106 .27 .0531 1.35 .1360 29 #8-32 .0110 85 .28 .0550 54 .1378 3.5 .0114 .29 .0551 1.4 .1405 28 .0015 84 .0571 1.45 9/64 .1406 .0118 .30 .0591 1.5 .1417 3.6 .0120 83 .0595 53 .1440 27 .0125 82 .0610 1.55 .1457 3.7 .0126 .32 1/16 .0625 #1-64 .1470 26 3/16-24NS .0130 81 .0630 1.6 .1476 3.75 .0134 .34 .0635 52 #1-72 .1495 25 #10-24 .0135 80 .0650 1.65 .1496 3.8 .0138 .35 .0669 1.7 .1520 24 .0142 .36 .0670 51 #2-56 .1535 3.9 .0145 79 .0689 1.75 .1540 23 .0150 .38 .0700 50 #2-64 5/32 .1562
1/64 .0156 .0709 1.8 .1570 22 3/16-32NS .0157 .4 .0728 1.85 .1575 4. .0160 78 .0730 49 .1590 21 #10-32 .0165 .42 .0748 1.9 .1610 20 .0173 .44 .0760 48 .1614 4.1 .0177 .45 .0768 1.95 .1654 4.2 .0180 77 5/64 .0781 #3-48 .1660 19 .0181 .46 .0785 47 .1673 4.25 .0189 .48 .0787 2. .1693 4.3 .0197 .5 .0807 2.05 .1695 18 .0200 76 .0810 46 #3-56 11/64 .1719 .0210 75 .0820 45 .1730 17 #12-24 .0217 .55 .0827 2.1 .1732 4.4 .0225 74 .0846 2.15 .1770 16 7/32-24NS .0236 .6 .0860 44 .1772 4.5 .0240 73 .0866 2.2 .1800 15 #12-28 .0250 72 .0886 2.25 .1811 4.6 .0256 .65 .0890 43 #4-40 .1820 14 .0260 71 .0906 2.3 .1850 13 .0276 .7 .0925 2.35 .1850 4.7 .0280 70 .0935 42 #4-48 .1870 4.75 .0292 69 3/32 .0938 3/16 .1875 .0295 .75 .0945 2.4 .1890 4.8 .0310 68 .0960 41 .1890 12 7/32-32NS
1/32 .0312 .0965 2.45 .1910 11 .0315 .8 .0980 40 .1929 4.9 .0320 67 .0984 2.5 .1935 10 .0330 66 .0995 39 #5-40 .1960 9 .0335 .85 .1015 38 .1969 5. .0350 65 .1024 2.6 .1990 8 1/4-20 .0354 .9 .1040 37 #5-44 .2008 5.1 .0360 64 .1063 2.7 .2010 7 .0370 63 .1065 36 #6-32 13/64 .2031 .0374 .95 .1083 2.75 .0380 62 7/64 .1094
Page 167Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845
Fuller Countersinks · Counterbores · Tapered Drills · Plug Cutters · Step Drills · Stop Collars
Decimal Equivalency Chart (Part 2)
Inch Dec- imal
Wire & Letter mm Tap
Sizes Inch Dec- imal
Wire & Letter mm Tap
Sizes Inch Dec- imal mm Tap
Sizes .2040 6 21/64 .3281 11/16 .6875 3/4-16NF .2047 5.2 .3307 8.4 .6890 17.5 .2055 5 .3320 Q 3/8-24NF 45/64 .7031 .2067 5.25 .3346 8.5 .7087 18. .2087 5.3 .3386 8.6 23/32 .7188 1/2-14 Pipe .2090 4 .3390 R 1/8-27 Pipe .7283 18.5 .2126 5.4 .3425 8.7 47/64 .7344 .2130 3 1/4-28 11/32 .3438 .7480 19. .2165 5.5 .3445 8.75 3/4 .7500
7/32 .2188 .3465 8.8 49/64 .7656 7/8-9NC .2205 5.6 .3480 S .7677 19.5 .2210 2 .3504 8.9 25/32 .7812 .2244 5.7 .3543 9. .7874 20. .2264 5.75 .3580 T 51/64 .7969 .2280 1 .3583 9.1 .8071 20.5 .2283 5.8 23/64 .3594 13/16 .8125 7/8-14NF .2323 5.9 .3622 9.2 .8268 21. .2340 A .3642 9.25 53/64 .8281
15/64 .2344 .3661 9.3 27/32 .8438 .2362 6. .3680 U 7/16-14NC .8465 21.5 .2380 B .3701 9.4 55/64 .8594 .2402 6.1 .3740 9.5 .8661 22. .2420 C 3/8 .3750 7/8 .8750 1-8NC .2441 6.2 .3770 V .8858 22.5 .2460 D .3780 9.6 57/64 .8906 .2461 6.25 .3819 9.7 .9055 23. .2480 6.3 .3839 9.75 29/32 .9062 1-12NF
1/4 .2500 E .3858 9.8 59/64 .9219 3/4-14 Pipe .2520 6.4 .3860 W 7/16-20 .9252 23.5 .2559 6.5 .3898 9.9 15/16 .9375 1-14NS .2570 F 5/16-18NC 25/64 .3906 .9449 24. .2598 6.6 .3937 10. 61/64 .9531 .2610 G .3970 X .9646 24.5 .2638 6.7 .4040 Y 31/32 .9688
17/64 .2656 13/32 .4062 .9843 25. .2657 6.75 .4130 Z 63/64 .9844 1-1/8-7NC .2660 H .4134 10.5 1 1.0000 .2677 6.8 27/64 .4219 1/2-13 1.0093 25.5 .2717 6.9 .4331 11. 1-1/64 1.0156 .2720 I 5/16-24NF 7/16 .4375 1/4-18 Pipe 1.0236 26. .2756 7. .4528 11.5 1-1/32 1.0312 .2770 J 29/64 .4531 1/2-20 1.0433 26.5 .2795 7.1 15/32 .4688 1-3/64 1.0469 1-1/8-12NF .2810 K .4724 12. 1-1/16 1.0625
9/32 .2812 5/16-32NS 31/64 .4844 9/16-12 1.0630 27. .2835 7.2 .4921 12.5 1-5/64 1.0781 .2854 7.25 1/2 .5000 1.0827 27.5 .2874 7.3 .5118 13. 1-3/32 1.0938 .2900 L 33/64 .5156 9/16-18 1.1024 28. .2913 7.4 17/32 .5312 1-7/64 1.1094 1-1/4-7NC .2950 M .5315 13.5 1.1220 28.5 .2953 7.5 35/64 .5469 1-1/8 1.1250
19/64 .2969 .5512 14. 5/8-11 1-9/64 1.1406 .2992 7.6 9/16 .5625 1.1417 29. .3020 N .5709 14.5 1-5/32 1.1562 1-11-1/2 Pipe .3031 7.7 37/64 .5781 5/8-18NF 1.1614 29.5 .3051 7.75 .5906 15. 3/8-18 Pipe 1-11/64 1.1719 1-1/4-12NF .3071 7.8 19/32 .5938 1.1811 30.0 .3110 7.9 39/64 .6094 1-3/16 1.1875 1-3/8 x 6
5/16 .3125 3/8-16NC .6102 15.5 1.2008 30.5 .3150 8. 5/8 .6250 11/16-16NS 1-13/64 1.2031 .3160 O .6299 16. 1-7/32 1.2188 .3189 8.1 41/64 .6406 1.2205 31.0 .3228 8.2 .6496 16.5 1-15/64 1.2344 .3230 P 21/32 .6562 3/4-10NC 1.2402 31.5 .3248 8.25 .6693 17. 1-1/4 1.2500 .3268 8.3 43/64 .6719
Page 168
Page 169Hickory Saw & Tool 1-800-762-8999 Fax 1-800-762-6845