VERTICAL/WALLVERTICAL/WALLAPPLICATIONAPPLICATION

VERTICAL/WALLVERTICAL/WALLAPPLICATIONAPPLICATION

PRIMING YOUR WALLPRIMING YOUR WALL

PRIMER:PRIMER:

• MAY BE APPLIED DIRECTLY OVER MAY BE APPLIED DIRECTLY OVER DRYWALL, MASONRY, DRYWALL, MASONRY, CONCRETE, CONCRETE BLOCK, CONCRETE, CONCRETE BLOCK, OR ICF/STYROFOAM SUBSTRATESOR ICF/STYROFOAM SUBSTRATES

SCRATCH COATSCRATCH COAT

• CONCRETE, CONCRETE BLOCK, CONCRETE, CONCRETE BLOCK, AND OTHER WALLS MAY BE WIRED AND OTHER WALLS MAY BE WIRED TO ACCEPT THE APPLICATIONTO ACCEPT THE APPLICATION

• APPLY SCRATCH COAT TO SMOOTH OUT APPLY SCRATCH COAT TO SMOOTH OUT THE WALL, THEN BRUSH ROUGHTHE WALL, THEN BRUSH ROUGH

• CURE SCRATCH COAT CURE SCRATCH COAT FOR 24 HOURS MINIMUMFOR 24 HOURS MINIMUM

SCRATCH COAT:SCRATCH COAT:RECOMMENDED MIXRECOMMENDED MIX

SCRATCH COAT:SCRATCH COAT:

• WALLWALL MIX MIX

• AVAILABLE IN WHITE OR GRAYAVAILABLE IN WHITE OR GRAY

• 50 POUNDS COVERS UP TO50 POUNDS COVERS UP TO56 SQUARE FEET AT 1/8” THICK56 SQUARE FEET AT 1/8” THICK

• ALLOW TO DRY ALLOW TO DRY COMPLETELYCOMPLETELYBEFORE NEXT STEPBEFORE NEXT STEP

STENCILSTENCIL

BROWN COAT:BROWN COAT:

• RE-APPLY RE-APPLY PRIMER PRIMER WITH PUMP SPRAYERWITH PUMP SPRAYER

• USE THE SAMEUSE THE SAME WALL WALL MIXMIX

• WHILE BROWN COAT IS STILL TACKY WHILE BROWN COAT IS STILL TACKY ADHERE YOUR STENCIL TO THE BROWN ADHERE YOUR STENCIL TO THE BROWN COAT BY LIGHTLY TROWELINGCOAT BY LIGHTLY TROWELING

• ALLOW BROWN COAT TO SET SLIGHTLY ALLOW BROWN COAT TO SET SLIGHTLY (NO LONGER SOFT)(NO LONGER SOFT)

COLOR COAT/TOP COATCOLOR COAT/TOP COAT

COLORPAXCOLORPAX

• DRY PIGMENTDRY PIGMENT

• PRE-MEASUREDPRE-MEASURED

• MIXES DIRECTLY INTO WALL MIXMIXES DIRECTLY INTO WALL MIX

LIQUID COLORLIQUID COLOR

• LIQUID PIGMENTLIQUID PIGMENT

• MIXES DIRECTLY INTO WALL MIXMIXES DIRECTLY INTO WALL MIX

APPLYING COLOR COATAPPLYING COLOR COAT

• APPLY THE TOP COAT USING APPLY THE TOP COAT USING WALL MIX WALL MIX MIXED WITH MIXED WITH THE DESIRED COLORANTS THE DESIRED COLORANTS (LIQUID COLOR OR COLORPAX)(LIQUID COLOR OR COLORPAX)

• TROWEL OR SPRAY COLOR COAT TROWEL OR SPRAY COLOR COAT THINLY OVER THE SURFACE THINLY OVER THE SURFACE

• OUTLINE OF STENCIL SHOULD BE OUTLINE OF STENCIL SHOULD BE VISIBLE THROUGH THE FINISH COATVISIBLE THROUGH THE FINISH COAT

TEXTURINGTEXTURING

• RELEASE AGENT IS APPLIED RELEASE AGENT IS APPLIED AND THE SURFACE TEXTUREDAND THE SURFACE TEXTURED

• CLEAR LIQUID RELEASE OR CLEAR LIQUID RELEASE OR COLORED POWDER RELEASE COLORED POWDER RELEASE MAY BE USED MAY BE USED

• DO NOT ALLOW THE RELEASE AGENT DO NOT ALLOW THE RELEASE AGENT TO GET ON THE BASE COATTO GET ON THE BASE COAT

• TO ALLOW TEXTURING, RELEASE MUST TO ALLOW TEXTURING, RELEASE MUST BE APPLIED IMMEDIATELY AFTER THE BE APPLIED IMMEDIATELY AFTER THE TOPCOAT, BECAUSE IT SETS UP TOPCOAT, BECAUSE IT SETS UP QUICKLYQUICKLY

PULLING YOUR STENCILPULLING YOUR STENCIL

• REMOVE STENCIL AS SOON AS THE REMOVE STENCIL AS SOON AS THE OVERLAY CHIPS FREELY FROM OVERLAY CHIPS FREELY FROM THE STENCIL (SAME-DAY)THE STENCIL (SAME-DAY)

• USE A WIRE BRUSH TO DETAIL JOINTSUSE A WIRE BRUSH TO DETAIL JOINTS

• DO NOT LEAVE STENCIL IN OVERNIGHTDO NOT LEAVE STENCIL IN OVERNIGHT

• ALLOW TO CURE FOR 24 HOURS BEFORE ALLOW TO CURE FOR 24 HOURS BEFORE CLEANING YOUR SURFACECLEANING YOUR SURFACE

• CONTINUE WITH THE SAME STEPSCONTINUE WITH THE SAME STEPSAS FOR CAST-IN-PLACE — WITH THE AS FOR CAST-IN-PLACE — WITH THE EXCEPTION OF SEALINGEXCEPTION OF SEALING

• IT IS CRITICAL TO SEAL ACCORDING TO IT IS CRITICAL TO SEAL ACCORDING TO THE OVERLAY MANUFACTURER’S THE OVERLAY MANUFACTURER’S SPECIFICATIONSSPECIFICATIONS

CLEAN & SEALCLEAN & SEAL