versadrill kmb .4 new october 2011, purchased for gallery ...versadrill kmb .4 new october 2011,...
TRANSCRIPT
VersaDrill KMB .4 New October 2011, Purchased for gallery drilling project for the USACE. Drilled 2850 LF of HQ Chucks capable of PQ Includes, water pump and spares
Drill Unit, Right Side Drill Unit, Front
Drill Unit, Left Side Drill Unit and Control Stand
Control Stand, Back Face of Control Stand
Power Pack, Right Side Power Pack, Rear
Triplex Water Pump, Head Power Pack, Left Side
Triplex Pump, Information Placard Triplex Pump, Hydraulic Motor, Inlet and Outlet
• Underground or surface version
• Heliportable
• Made in aluminium or steel
• Total weight in aluminium
4950 lb (2245 kg)
KmB .4Lightweight to save time
Surface Kit
KmB .4Technical specifi cations
199, St-Philippe RdVal-d’Or, QC • Canada - J9P 4N7
Phone: 819-738-4567 • Fax: 819-738-4568www.versadrillcanada.com
Hydraulic moduleFloating rotary head
Torque limit on rotary head
Hydraulic pump 65 US gal/min (246 l/min)@ 1800 RPM (max 4000 psi (275 bar))
Open loop hydraulic system
Hydraulic pressurized tank 34 US gal (128 l)
Oil heat exchangers Water cooling (Air cooler optional)
Drilling capacity
* Recommended size for maximum
performance
*A 1 3/4” (44,5 mm) 1550 ft (472 m)
*B 2 3/16” (55,6 mm) 1300 ft (400 m)
N 2 3/4” (69,9 mm) 655 ft (200 m)
H 3 1/2” (88,9 mm) 180 ft (55 m)
H casing 4 1/2” (114,3 mm) 98 ft (30 m)
Drilling capacity is calculated on a 90 degree down hole and will depend on in-hole tools, ground conditions, drilling techniques and equipment used.
Recommended electric engine: 100 HP ( 74,5 Kw) at 1800 RPMRecommended diesel engine: 100 HP ( 74,5 Kw) at 2100 RPM
Rotary head and rod holderHolding capacity 14000 lb (6350 kg)
Spindle interior dimension 4.9” (124 mm)
Chuck operation Spring closed and hydraulically opened
Final drive HV-60-2 chain in an oil bath
Hydraulic Motor 80 cc variable
Transmission HI-LO 2 speeds
Rotary Head Ratio 1:2
Lubrication Pump pressurized, fi lter and cooler
Fabrication Aluminium and Steel (all steel optional)
Speed 0 to 1500 RPM
Filtration10 micron absolute fi lter on return line
High pressure fi lter
One strainer inside the hydraulic tank connected to the suction
Feed frameHead stroke 5 ft 5 in (1,68 m)
Raising speed 300 ft/min (91 m/min)
Lowering speed 300 ft/min (91 m/min)
Pull capacity 9000 lb (4080 kg) @ 4000 psi
Push capacity 9000 lb (4080 kg) @ 4000 psi
Possible angle (Underground version) -90 to 90 degrees
Possible angle (Surface version) -8 to -90 degrees
Surface mastStroke 15 ft (4,57 m) on top of the head with cable
Pull speed 400 ft/min (121 m/min)
Speed of descent 780 ft/min (237 m/min)
Single line pull capacity 6500 lb (2950 kg) @ 4000 psi
Rod pull length 10 ft (3 m)
Wireline hoistCable capacity 3/16” (4,8 mm) 1500 ft (457 m)
Empty pull capacity 2000 lb (907 kg)
Full pull capacity 650 lb (295 kg)
Variable speed as needed
WeightElectric power unit 1352 lb (613 kg)
Diesel power unit 750 lb (340 kg)
Hydraulic pump and tank 584 lb (365 kg) dry884 lb (400 kg) wet
Control panel 214 lb (97 kg)
Drill head 550 lb (249 kg)
Drill head hydraulic motor 70 lb (32 kg)
Drill head transmission 85 lb (39 kg)
Rod holder 200 lb (90 kg)
Feed frame 595 lb (269 kg)
Mast base 400 lb (182 kg)
Surface mast 550 lb (250 kg)
Wireline 100 lb (45 kg)
Hydraulic hoses 800 lb (363 kg)
2 Speed transmissionSpeed Ratio RPM Maximum Torque
LO 3.46:1 0-361 2098 lb*ft (2840 N*m) @ 361 RPM
HI 1:1 0-1500 606 lb*ft (820 N*m) @ 1500 RPM
Speed and torque based on a 80 cc hydraulic motor at 4000 psi (275 bar)
The manufacturer reserves the right to make modifi cations without prior notice
53 in
(134
,62
cm)
20 in(50,8 cm)
24 in
(61 cm)
10,2
5 in
(26
cm)
105
in (2
66,7
cm)
Retra
cted
102
in (2
59 cm
)
Exte
nded
162
in (4
11,4
8 cm
)
33 in(83,82 cm)
68 in (172,72 cm
)
55 in
(139
.7 c
m)
30,5 in(77,4 cm)24 in
(61 cm)
30,5 in (77,5 cm)84 in (213,4 cm)
37 in (94 cm)
32 in (81,28 cm)56 in (1
42,24 cm)
58 in
(147
,32
cm)
Height when flat: 47 in (119,4 cm)
KmB .4Dimensions
