vento series - blauberg north america · vento expert a50-1 pro heat recovery singe-room unts...

26
Single-room heat recovery units VENTO Series

Upload: others

Post on 22-Oct-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

  • Single-room heat recovery units

    VENTOSeries

  • 2

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • CONTENT

    VENTO Expert A50-1 Pro 4

    VENTO Expert A50-1 W 8

    VENTO Expert DUO A30-1 Pro 12

    VENTO Expert DUO A30-1 W 16

    VENTO ECO2 A50 Pro 20

    3SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 Pro

    Heat recovery efficiency: up to 97 %

    Power: from 3.61 WSFP: from 0.75 W/l/s

    Noise level: from 11 dBA

    FeaturesArrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises.Reducing heat losses caused by ventilation due to heat recovery.Humidity balance and regulated air exchange create individually controlled microclimate.Coordinated network based on several integrated single-room ventilation units with central control.

    Design

    Filters MERV6

    Decorative front panel

    Ceramic energy core

    Filter MERV14(optional)

    Reversible EC fan

    Sensor operation mode switches

    Air duct

    Sound insulating material Outer ventilation

    hood

    Remote control

    Easy maintenance.Indoor unit is opened by pressing the latches on both sides.

    One of the best regeneration efficiency on the market due to innovative hexagonal structure of the heat core cells.

    Integrated automatic air shutters prevent air back drafting.

    The specially designedfront panel can be closed manually to ensure 100 % air tightness and protect against wind impact.

    Designation key

    Model Air duct Nominal air flow [m³/h] Front panel Hood type Control

    VENTO Expert A: round air duct 50 -1: flat front panel _: hood for standard walls (by default)

    S: metal hood for thin walls

    Pro: remote control

    Air flow: up to 29 CFM 14 l/s

    4

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 Pro

    Heat and moisture regeneration

    ControlControl of the unit operation mode is performed by means of sensor control panel located on the unit casing or a remote controller.

    UNIT OPERATING LOGIC IN WINTER PERIOD

    Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers its heat energy and moisture to it. As the ceramic regenerator gets warmed up, the unit switches to the supply mode.

    Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.When the ceramic regenerator is cooled down, the unit switches to the extract air mode.

    INDOOR

    +68°F

    19°F 14°F

    +62°F

    OUTSIDE OUTSIDE

    Phase 1 (70 seconds)Air extraction from the premise

    Phase 2 (70 seconds)Air supply to the room

    Heat regeneration mode

    Speed selection and OFF button

    Heat regeneration mode

    Ventilation mode

    ON/OFF button

    3 unit speeds

    Ventilation mode

    Party timer: high speed for 4 hours

    Night timer: low speed for 8 hours

    The unit is equipped with a humidity sensor for indoor humidity control.Connection of the units in series ensures balanced ventilation. First unit in the chain becomes the master one.

    Ventilation mode of the entire system can be controlled by means of the control panel on the master unit. A signal from the remote control is received by the master unit only.

    VENTO Expert A50-1 Pro VENTO Expert A50-1 Pro VENTO Expert A50-1 Pro VENTO Expert A50-1 Pro

    ~ 100-230 V

    Remotecontrol

    Control line

    Power line

    Control line

    Power line

    Control line

    Power line

    5SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 Pro

    MountingThe unit is designed for through-the-wall installation inside a prepared hole in an outer wall of the building.The best ventilation solution is pairwise installation of reverse phase connected units. Some units ensure supply of fresh air to the room and the other units extract air from the premise. This way the most efficient balanced ventilation is arranged.

    In case of brand new construction, units are mounted in two stages:• Pre-installation at the stage of the indoor finishing and outer

    decorative wall finishing. It includes installation of an air duct, an outer ventilation hood and cable installation.

    • Final mounting before commissioning of a house. It includes installation of a regenerator with a fan and filters and mounting and wiring of an indoor unit with a controller and shutters.

    Kitchen Bathroom Room

    Room Room

    Hall

    Balcony

    Overall dimensions [in]

    11

    9 3/16

    11 3

    /16

    11 13

    /16

    9 7/16 - 19 11/16

    2 1/2

    Ø6 5/

    16

    9 3/16

    11 3

    /16

    Ø6 5/

    16

    12 3/16

    10 1/

    4

    5 15/16 - 19 11/16

    2 1/2

    VENTO Expert A50-1 Pro VENTO Expert A50-1 S Pro (for thin walls)

    Angular mounting into a wall with standard thickness usingKIT BlauPlast white 160 / KIT BlauPlast chrome 160

    6

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 Pro

    Technical data

    Parameters VENTO Expert A50-1 Pro

    Speed I II III

    Voltage [V / 50 (60) Hz] 100-230

    Power [W] 3.61 4.15 5.20

    Current [A] 0.025 0.030 0.039

    RPM [min⁻1] 800 1300 1900

    Air flow in ventilation mode [CFM (l/s)] 9 (4) 18 (8) 29 (14)

    Air flow in heat recovery mode [CFM (l/s)] 5 (2) 9 (4) 15 (7)

    SFP [W/l/s] 1.73 1.00 0.75

    Filter MERV6 (Option: MERV14 PM2.5 > 99 %*)

    Transported air temperature [°F] +5…+104

    Sound pressure level at 1 ft [dBA (Sones)] 20 (0.6) 27 (1.0) 30 (1.2)

    Sound pressure level at 3 ft [dBA (Sones)] 11 (0.3) 18 (0.5) 21 (0.6)

    Outdoor sound pressure attenuation [dBA (Sones)] in accordance wi th DIN EN 20140 42 (2.5)

    Regeneration efficiency [%] in accordance with DIBt LÜ-A 20 97 90 82

    SEC Class A

    Ingress Protection Rating IP24* maximum air flow 24 CFM

    BLAUBERG VENTO Expert A50-1Pro

    38dB

    25 m³/h

    2017

    Accessories

    Name Description

    Pre-installation Kit VENTO Expert A50-1Pre-installation kit for mounting into a wall with standard thickness. Includes: • Air duct; • AH 160 outer ventilation hood; • Plastic foam plug.

    Pre-installation Kit VENTO Expert A50-1 SPre-installation kit for mounting into a thin wall. Includes: • Air duct; • AH-S 160 outer ventilation hood; • Plastic foam plug.

    Completion Kit VENTO Expert A50-1Final mounting kit. Includes: • Internal unit with a heat regenerator, a fan and MERV6 filters; • Indoor unit with a controller and shutters; • Remote control.

    FP VENTO Expert A50 G3 MERV6 filters (2 pcs.)

    FP VENTO Expert A50 F8

    Includes: • Plastic frame (1 pc.); • MERV4 pre-filter (1 pc.); • MERV14 filter (1 pc.). Filtration rate PM2.5 99 %. • MERV14 filter reduces airflow of the unit down to 24 CFM

    FB-Vento Expert Remote control

    KIT BlauPlast white 160 Mounting kit for angular installation in walls with standard thickness

    KIT BlauPlast chrome 160 Kit for angular mounting with stainless stees outer grille

    PP 160 Plastic outer grille with pipe for mounting from indoor

    CD-1 CO2 sensor with LED indication and On/Off button

    CD-2 CO2 sensor

    7SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 W

    Heat recovery efficiency: up to 97 %

    Power: from 4.45 WSFP: from 1.02 W/l/s

    Noise level: from 11 dBA

    FeaturesArrangement of efficient energy-saving, supply and exhaust, single-room ventilation in f lats , houses, cottages, social and commercial premises.Reducing heat losses caused by ventilation due to heat recovery.Humidity balance and regulated air exchange create individually controlled microclimate.Wi-F i communication between several single-room ventilation units for coordinated operation.Controlled by Android or iOS smartphone or tablet.

    Filters MERV6

    Decorative front panel

    Ceramic energy core

    Filter MERV14(optional)

    Fan with reversible EC motor

    WLAN antenna

    Air duct

    Sound insulating material

    Externalventilation hood

    One of the best regeneration efficiency on the market due to innovative hexagonal structure of the heat core cells.

    Integrated automatic air shutters prevent air back drafting.

    Design

    Humidity sensor

    Speed 1/2/3 | Off

    Heat regeneration mode

    Ventilation mode

    Easy maintenance.Indoor unit is opened by pressing the latches on both sides.

    The specially designed front panel can be closed manually to ensure 100% air tightness and protect against wind impact.

    Built-in Wi-Fi for wireless communication between units and Android or iOS device control.

    Designation key

    Model Air duct Nominal air flow [m³/h] Front panel Hood type Control

    VENTO Expert A: round air duct 50 _: no flat front panel -1: flat front panel

    _: hood for standard walls (by default)

    S: metal hood for thin walls

    W: wireless control

    Air flow: up to 29 CFM 14 l/s

    8

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert A50-1 W

    Heat and moisture regeneration

    ControlThe units can be connected by Wi-Fi for synchronized operation.

    UNIT OPERATING LOGIC IN WINTER PERIOD

    Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers its heat energy and moisture to it. As the ceramic regenerator gets warmed up, the unit switches to the supply mode.

    Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.When the ceramic regenerator is cooled down, the unit switches to the extract air mode.

    INDOOR

    +68 °F

    19°F 14°F

    +62°F

    OUTSIDE OUTSIDE

    The units can be connected by Wi-Fi.Blauberg Vento app for Android or iOS devices is available at Google Play and App Store.

    The VENTO Expert A50-1 W unit can be connected to a laptop for advanced settings:• Master or slave • Supply or exhaust operation in ventilation mode • Connection through a Wi-Fi router or directly to a smartphone.

    Heat regeneration mode

    ON/OFF button

    Speed

    Ventilation mode

    Party timer: high speed for 4 hours

    Nigh timer:low speed for 8 hours

    Phase 1 (70 seconds)Air extraction from the premise

    Phase 2 (70 seconds)Air supply to the room

    9SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    MountingThe unit is designed for through-the-wall installation inside a prepared hole in an outer wall of the building.The best ventilation solution is pairwise installation of reverse phase synchronized units. Some units ensure supply of fresh air to the room and the other units extract air from the premise. This way the most efficient balanced ventilation is arranged.

    In case of brand new construction, units are mounted in two stages:• Pre-installation of an air duct and an outer ventilation hood at the

    stage of indoor finishing and outer decorative wall finishing.• Completion of the installation before commissioning of a house. It

    includes installation of the indoor unit with controller and shutters, the cartridge, the regenerator, the fan and the filters.

    VENTO Expert

    VENTOExpertDUO

    VENTOExpertDUO

    Bathroom Kitchen

    Balcony

    Room Room

    Room

    VENTO Expert

    VENTO Expert

    VENTO Expert

    Hall

    Overall dimensions [in]

    VENTO Expert A50-1 W VENTO Expert A50-1 S W (for thin walls)

    Angular mounting into a wall with standard thickness usingKIT BlauPlast white 160 / KIT BlauPlast chrome 160

    VENTO Expert A50-1 W

    11

    9 1/4

    11 1/

    4

    11 13

    /16

    9 13/16 - 19 11/16

    2 13/16

    Ø6 5/

    16

    9 1/4

    11 1/

    4

    Ø6 5/

    16

    12 3/16

    10 1/

    4

    5 15/16 - 19 11/16

    2 13/16

    10

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    Technical data

    Parameters VENTO Expert A50-1 W

    Speed I II III

    Voltage [V / 50 (60) Hz] 100-230

    Power [W] 4.45 5.08 7.06

    Current [A] 0.035 0.040 0.059

    RPM [min⁻1] 800 1300 1900

    Air flow in ventilation mode [CFM (l/s)] 9 (4) 18 (8) 29 (14)

    Air flow in heat recovery mode [CFM (l/s)] 5 (2) 9 (4) 15 (7)

    SFP [W/l/s] 2.14 1.22 1.02

    Filter MERV6 (Option: MERV14 PM2,5 > 99 %*)

    Transported air temperature [°F] +5…+104

    Sound pressure level at 1 ft [dBA (Sones)] 20 (0.6) 27 (1.0) 30 (1.2)

    Sound pressure level at 3 ft [dBA (Sones)] 11 (0.3) 18 (0.5) 21 (0.6)

    Outdoor sound pressure attenuation [dBA (Sones)] in accordance with DIN EN 20140 42 (2.5)

    Regeneration efficiency [%] in accordance with DIBt LÜ-A 20 97 90 82

    SEC Class A

    Ingress protection rating IP24* maximum air flow 24 CFM

    VENTO Expert A50-1 W

    BLAUBERG VENTO Expert A50-1W

    38dB

    25 m³/h

    2017

    Accessories

    Name Description

    Pre-installation Kit VENTO Expert A50-1Pre-installation kit for mounting into a wall with standard thickness. Includes: • Air duct; • AH 160 outer ventilation hood; • Plastic foam plug.

    Pre-installation Kit VENTO Expert A50-1 SPre-installation kit for mounting into a thin wall. Includes: • Air duct; • AH-S 160 outer ventilation hood; • Plastic foam plug.

    Completion Kit VENTO Expert A50-1Final mounting kit. Includes: • Internal unit with a heat regenerator, a fan and MERV6 filters; • Indoor unit with a controller and shutters; • Remote control.

    FP VENTO Expert A50 G3 MERV6 filters (2 pcs.)

    FP VENTO Expert A50 F8

    Includes: • Plastic frame (1 pc.); • MERV4 pre-filter (1 pc.); • MERV14 filter (1 pc.). Filtration rate PM2.5 99 %. • MERV14 filter reduces airflow of the unit down to 24 CFM

    FB-Vento Expert Remote control

    KIT BlauPlast white 160 Mounting kit for angular installation in walls with standard thickness

    KIT BlauPlast chrome 160 Kit for angular mounting with stainless stees outer grille

    PP 160 Plastic outer grille with pipe for mounting from indoor

    CD-1 CO2 sensor with LED indication and On/Off button

    CD-2 CO2 sensor

    11SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert DUO A30-1 Pro

    Heat recovery efficiency: up to 85 %

    Power: from 2.00 WSFP: from 0.67 W/l/s

    Noise level: from 24 dBA

    FeaturesArrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises. Reducing heat losses caused by ventilation due to heat recovery. Humidity balance and regulated air exchange create individually controlled microclimate. Coordinated network based on several integrated single-room ventilation units with central control.

    Reversible EC fans

    Decorative front panel

    Ceramic energy accumulator(regenerator)

    Air duct

    One of the best regeneration efficiency on the market due to innovative hexagonal structure of the heat exchanger cells.

    Outer ventilation hood

    Easy maintenance. Indoor unit is opened by pressing the latches on both sides.

    Design

    Remote control

    Air streams separator

    MERV6 filters

    Sensor operation mode switches

    Designation key

    Model Fans Air duct Nominal air flow [m³/h] Unit modification Control

    VENTO Expert DUO: two fans A: round air duct 30 1 Pro

    Air flow: up to 18 CFM 8 l/s

    12

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert DUO A30-1 Pro

    Heat and moisture regeneration

    ControlControl of the unit operation mode is performed by means of the sensor control panel located on the unit casing or the remote controller.

    UNIT OPERATING LOGIC IN WINTER PERIOD

    One fan supplies fresh and cold air from outdoor, which flows through the correspondent part of the ceramic regenerator and absorbs accumulated heat and humidity.At the same time, another fan extracts slate and warm air from indoor, that flows through the other part of the ceramic regenerator and transfers heat energy and moisture to it.

    After 70 seconds operation the fans change the rotation direction and opposite processes start.

    OUTDOOR

    +62°F

    INDOOR

    Phase 1 (70 seconds) Phase 2 (70 seconds)

    Heat regeneration mode

    Speed selection and OFF button

    Heat regeneration mode

    Ventilation mode

    ON/OFF button

    3 unit speeds

    Ventilation mode

    Party timer: high speed activation for 4 hours

    Night timer: low speed activation for 8 hours

    VENTO Expert DUO either can operate as independent unit or can be wired with other units in a house Vento Expert A50-1 to be controlled with a master unit. In this case, only the master unit receives a signal from the remote control.

    VENTO Expert DUO is equipped with a humidity sensor for indoor humidity control. If humidity increases above a set point, the unit boosts to the high speed independent of other units in the system.

    VENTO Expert A50-1 Pro VENTO Expert A50-1 Pro VENTO Expert DUO A30-1 Pro

    ~ 100-230 V

    Remote control

    Control line

    Power line

    Control line

    Power line

    +68°F

    14°F

    19°F

    +68°F

    INDOOR

    +62°F

    OUTDOOR

    19°F

    14°F

    13SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    MountingThe unit is designed for through-the-wall installation inside a prepared core hole in an outer wall of the building.

    VENTO Expert DUO must be installed in each room with high humidity like kitchen, bathroom to be ventilated while Vento Expert must be installed in each living room to be ventilated.

    VENTO Expert DUO A30-1 Pro

    Overall dimensions [in]

    VENTO Expert DUO A30-1 Pro

    VENTO Expert

    VENTOExpertDUO

    VENTOExpertDUO

    Bathroom Kitchen

    Balcony

    Room Room

    Room

    VENTO Expert

    VENTO Expert

    VENTO Expert

    Hall

    VENTO Expert A50-1 Pro

    VENTO Expert DUO A30-1 Pro

    9 1/4

    11 1/

    4

    Ø6 5/

    16

    12 3/16

    10 1/

    4

    11 - 19 11/16

    2 13/16

    14

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    Technical data

    Parameters VENTO EXPERT DUO A30-1 Pro

    Speed I II III

    Voltage [V / 50 (60) Hz] 100-240

    Power [W] 2.00 3.70 6.40

    Current [A] 0.027 0.043 0.067

    RPM [min⁻1] 1600 2200 2500

    Maximum air flow [CFM (l/s)] 6 (3) 12 (6) 18 (8)

    Air flow in humidity extract mode [CFM (l/s)] 35 (16)

    SFP [W/l/s] 0.72 0.67 0.77

    Filter MERV6

    Transported air temperature [°F] +5…+104

    Sound pressure level at 1 ft [dBA (Sones)] 33 (1.2) 40 (2.0) 43 (2.5)

    Sound pressure level at 3 ft [dBA (Sones)] 24 (0.5) 31 (1.0) 34 (1.2)

    Outdoor sound pressure attenuation [dBA (Sones)] in accordance with DIN EN 20140 42 (2.5)

    Regeneration efficiency [%] in accordance with DIBt LÜ-A 20 up to 85

    SEC Class A

    Ingress protection rating IP24

    Accessories

    Name Description

    FP Vento Expert DUO A50 G3 MERV6 filter kit (2 pcs.)

    FB Vento Expert A50 Remote control

    AH-5 white 160 DUO Stainless steel ventilation hood, painted white

    AH-5 chrome 160 DUO Bushed stainless steel ventilation hood

    AH chrome 160 DUO Bushed stainless steel ventilation hood

    AH white 160 DUO Aluminum ventilation hood, painted white

    PP 160/0.5 Outer ventilation hood for mounting from inside

    CD-1 CO2 sensor with LED indication and on/off button

    CD-2 CO2 sensor

    LST Vento Expert DUO Air stream separator

    BLAUBERG VENTO Expert DUOA30 -1 Pro

    51dB

    30 m³/h

    2017

    VENTO Expert DUO A30-1 Pro

    15SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO Expert DUO A30-1 W

    Heat recovery efficiency: up to 85 %

    Power: from 2.17 WSFP: from 0.66 W/l/s

    Noise level: from 24 dBA

    FeaturesArrangement of balanced energy saving, supply and exhaust, single-room ventilation in kitchen, bathroom and utility room.Reducing heat losses caused by ventilation due to heat recovery.Humidity balance and regulated air exchange create individually controlled microclimate.Wi-F i communication between several single-room ventilation units for coordinated operation.Controlled by Android or iOS smartphone or tablet.

    Reversible EC fans

    Decorative front panel

    Ceramic energy accumulator(regenerator)

    Air duct

    One of the best regeneration efficiency on the market due to innovative hexagonal structure of the heat exchanger cells.

    Outer ventilation hood

    Built-in Wi-Fi for wireless communication between units and Android or iOS device control.

    Air streams separator

    MERV6 filters

    Design

    Heat regeneration mode

    ON/OFF button

    3 unit speeds

    Ventilation mode

    Party timer: high speed for 4 hours

    Night timer: low speed for 8 hours

    Speed selection and OFF button

    Heat regeneration mode

    Ventilation mode

    Operation mode switches

    Designation key

    Model Fans Air duct Nominal air flow [m³/h] Unit modification Control

    VENTO Expert DUO: two fans A: round air duct 30 1 W: wireless control

    Air flow: up to 18 CFM 8 l/s

    16

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    Party timer: high speed for 4 hours

    Night timer: low speed for 8 hours

    VENTO Expert DUO A30-1 W

    Heat and moisture regeneration

    UNIT OPERATING LOGIC IN WINTER PERIOD

    One fan supplies fresh and cold air from outdoor, which flows through the correspondent part of the ceramic regenerator and absorbs accumulated heat and humidity.At the same time, another fan extracts slate and warm air from indoor, that flows through the other part of the ceramic regenerator and transfers heat energy and moisture to it.

    After 70 second of operation, fans change their directions of rotations to the opposite ones, and everything happens vice versa.

    OUTDOOR

    +62°F

    INDOOR

    Phase 1 (70 seconds) Phase 2 (70 seconds)+68°F

    14°F

    19°F

    +68°F

    INDOOR

    +62°F

    19°F

    14°F

    ControlControl of the unit operation mode is performed by means of smartphone, sensor control panel located on the unit casing or a remote controller.

    The units can be connected by Wi-Fi. Blauberg Vento app for Android or iOS devices is available at Google Play and App Store.

    The VENTO Expert DUO A30-1 W unit can be connected to a laptop for advanced settings:• Master or slave; • Connection through a Wi-Fi router or directly to a smartphone.

    VENTO Expert DUO A30-1 W either can operate as independent unit, or can be connected with other units in a house to be controlled with a master unit. In this case, only the master unit receives a signal from the remote control.VENTO Expert DUO A30-1 W is equipped with a humidity sensor for indoor humidity control. If humidity will rise higher than set point, than the unit will boost to high speed independently from other units in the system.

    VENTO Expert A50-1 W

    VENTO Expert DUO A30-1 W

    OUTDOOR

    17SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    MountingVENTO Expert A50-1 W units should be installed in the living room and bedrooms while VENTO Expert DUO A30-1 W should be installed in kitchen, bathrooms and utility room.

    The unit is designed for through-the-wall installation inside a prepared hole in an outer wall of the building.

    Overall dimensions [in]

    VENTO Expert DUO A30-1 W

    VENTO Expert DUO A30-1 W

    VENTO Expert

    VENTOExpertDUO

    VENTOExpertDUO

    Bathroom Kitchen

    Balcony

    Room Room

    Room

    VENTO Expert

    VENTO Expert

    VENTO Expert

    Hall

    VENTO Expert A50-1 W

    VENTO Expert DUO A30-1 W

    9 1/4

    11 1/

    4

    Ø6 5/

    16

    12 3/16

    10 1/

    4

    11 - 19 11/16

    2 13/16

    18

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    BLAUBERG VENTO Expert DUOA30 -1 W

    51dB

    30 m³/h

    2017

    VENTO Expert DUO A30-1 W

    Technical data

    Parameters VENTO Expert DUO A30-1 W

    Speed I II III

    Voltage [V / 50 (60) Hz] 100-230

    Power [W] 2.17 3.66 6.62

    Current [A] 0.026 0.039 0.066

    RPM [min⁻1] 1600 2200 2500

    Maximum air flow [CFM (l/s)] 6 (3) 12 (6) 18 (8)

    Air flow in humidity extract mode [CFM (l/s)] 35 (16)

    SFP [W/l/s] 0.78 0.66 0.79

    Filter MERV6

    Transported air temperature [°F] +5…+104

    Sound pressure level at 1 ft [dBA (Sones)] 33 (1.2) 40 (2.0) 43 (2.5)

    Sound pressure level at 3 ft [dBA (Sones)] 24 (0.5) 31 (1.0) 34 (1.2)

    Outdoor sound pressure attenuation [dBA] in accordance with DIN EN 20140 42 (2.5)

    Regeneration efficiency [%] in accordance with DIBt LÜ-A 20 up to 85

    SEC Class A

    Ingress protection rating IP24

    Accessories

    Name Description

    FP Vento Expert DUO A30 G3 MERV6 filter kit (2 pcs.)

    FB Vento Expert A50 Remote control

    AH-5 white 160 DUO Stainless steel ventilation hood, painted white

    AH-5 chrome 160 DUO Brushed stainless steel ventilation hood

    AH chrome 160 DUO Brushed stainless steel ventilation hood

    AH white 160 DUO Aluminum ventilation hood, painted white

    PP 160/0.5 Outer ventilation hood for mounting from inside

    CD-1 CO2 sensor with LED indication and on/off button

    CD-2 CO2 sensor

    LST Vento Expert DUO Air stream separator

    19SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO ECO2 A50 Pro

    Heat recovery efficiency: up to 92 %

    Power: from 2.07 WSFP: from 0.50 W/l/s

    Noise level: from 13 dBA

    FeaturesArrangement of efficient energy-saving supply and exhaust single-room ventilation in flats, houses, cottages, social and commercial premises.Air purification with optional MERV14 filter PM2.5 99 %.Protection from outdoor noise.Reducing heat losses caused by ventilation due to heat recovery.Humidity balance and regulated air exchange create individually controlled microclimate.

    Internal grille with manually actuated shutters and a decorative panel

    Air duct

    Ceramic energy accumulator (regenerator)

    Reversible fan with EC motor

    Outer grille

    Noise insulating layer

    MERV6 filter

    MERV6 filter

    Design

    Designation key

    Model Number of units, items Air duct Nominal air flow [m³/h] Hood type Control

    VENTO Eco 2 A: round air duct 50 S1: round metal grille S: metal hood for thin walls

    Pro: sensor control panel

    Air flow: up to 29 CFM 14 l/s

    20

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITSVENTO ECO2 A50 Pro

    Heat and moisture regeneration

    ControlControl of the unit operation mode is performed by means of sensor control panel located on the unit casing or a remote controller.

    UNIT OPERATING LOGIC IN WINTER PERIOD

    Warm stale air is extracted from the premise, flows through the ceramic regenerator and transfers its heat energy and moisture to it. As the ceramic regenerator gets warmed up, the unit switches to the supply mode.

    Clean cold intake air flows through the regenerator and absorbs accumulated heat and humidity.When the ceramic regenerator is cooled down, the unit switches to the extract air mode.

    INDOOR

    +68°F19°F 14°F+62°F

    OUTSIDE OUTSIDE

    “Night” timer: min speed for 8 hours

    Speed 1

    “Party” timer: max speed for 4 hours

    Speed 2

    Speed 3

    Alarm indication

    Ventilation mode

    Heat regeneration mode

    Filter maintenance indication

    Low voltage (12 V) power supply between control panel and VENTO Eco2 units.

    Phase 1 (70 seconds)Air extraction from the room

    Phase 2 (70 seconds)Air supply to the room

    ~ 100-230 V

    21SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    MountingThe unit is designed for through-the-wall installation inside a prepared hole in an outer wall of the building.VENTO Eco2 A50 allows arranging the most efficient balanced ventilation. Two units, connected to single control panel, operate in reverse phases. One unit ensures supply of fresh air to the room and the

    other unit provides air extract from the premise. In regeneration mode units change direction of air flow to opposite one every 70 seconds.

    One unit is able to ventilate a room up to 25 m2. For bigger rooms two or more units must be installed.

    Overall dimensions [in]

    9 7/16

    9 7/16

    1 11/16

    8 1/4 - 1

    9 11/1612 3

    /16 - 19

    11/16

    5 9/16

    ø7 7/8

    7 7/8

    ø6 5/16 ø6 5/16

    3 3/8

    3 3/8

    1 1/81/2

    VENTO ECO2 A50 S1 Pro VENTO ECO2 A50 S Pro

    VENTO ECO2 A50 Pro

    Kitchen Bathroom

    Room

    Room Room

    Hall

    Balcony VENTO ECO2 A50 Pro

    VENTO ECO2 A50 Pro

    VENTO ECO A50 Pro

    VENTO ECO A50 Pro

    VENTO ECO2 A50 S1 PRO

    VENTO ECO2 A50 S Pro

    22

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    Accessories

    Name Description

    Completion Kit VENTO Eco A50 Cartridge with heat regenerator, fan and MERV6 filters. Square and round indoor grille with manually actuated shutters

    SE VENTO Eco A50 Pro Sensor control panel (white)

    SE VENTO Eco A50 Pro black Sensor control panel (black)

    Duct 160-500 19 11/16" air duct

    Duct 160-700 27 9/16" air duct

    AH chrome 160 Outer hood made of brushed stainless steel

    AH-S chrome 160 Outer hood for thin wall made of brushed stainless steel

    Decor 150Fs An white Outer grille

    KIT BlauPlast white 160 Kit for angular mounting with white outer grille

    KIT BlauPlast chrome 160 Kit for angular mounting with stainless stees outer grille

    FP VENTO Eco A50 G3 MERV6 filters (2 pcs.)

    FP VENTO Eco A50 F8 MERV4 + MERV14 filters (1 pc.). Filtration rate PM2.5 99 %. Combination of MERV4 + MERV14 filters reduces air flow down to 24 CFM

    L VENTO Eco A50 Fan

    PP 160 Plastic outer grille with pipe for mounting from indoor

    Technical data

    Parameters VENTO ECO2 A50 Pro

    Speed I II III

    Voltage [V / 50 (60) Hz] 100-230

    Power [W] 2.07 4.15 10.10

    Current [A] 0.030 0.049 0.098

    RPM [min⁻1] 1030 1760 2690

    Air flow in ventilation mode [CFM (l/s)] 9 (4) 18 (8) 29 (14)

    Air flow in heat recovery mode [CFM (l/s)] 9 (4) 18 (8) 29 (14)

    SFP [W/l/s] 0.50 0.50 0.73

    Filter MERV6 (option: MERV14 PM2.5 > 99 %*)

    Transported air temperature [°F] -22…+122

    Sound pressure level at 1 ft [dBA] In accordance with ISO 3741: 2004 22 29 32

    Sound pressure level at 3 ft [dBA] In accordance with ISO 3741: 2004 13 20 23

    Outdoor sound pressure attenuation [dBA] according to DIN EN 20140 41

    Regeneration efficiency [%] In accordance with DIBt LÜ-A 20 92 86 78

    SEC Class A

    Ingress protection rating IP24* maximum air flow 24 CFM

    VENTO ECO2 A50 Pro

    BLAUBERG VENTO Eco2 A50 S1Pro

    40dB

    50 m³/h

    2017

    23SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • SINGLE-ROOM AIR HANDLING UNITSHEAT RECOVERY SINGLE-ROOM UNITS

    24

    2018 | SINGLE-ROOM HEAT RECOVERY UNITS

    www.blauberg.us

  • HEAT RECOVERY SINGLE-ROOM UNITS

    25SINGLE-ROOM HEAT RECOVERY UNITS | 2018

    www.blauberg.us

  • 11/2017

    Technical changes reserved.Illustrations and texts are non-binding.

    Blauberg Ventilatoren174 N. 36th Street

    Lafayette, IN 47905tel.: +1 765 780 7139

    [email protected]

    www.blaubergventilatoren.de