vbo diagnostic tools manual (dx350lc-3/dx380lc-3)autocd.info/vbomanualen.pdf · 1 joystick check -...
TRANSCRIPT
![Page 1: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/1.jpg)
VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)
Corporate Research & Development Division
Electrical & Electronics Center
Distribution Date : 2013. 12. 30
Ver. 3.0
![Page 2: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/2.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
2
![Page 3: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/3.jpg)
VBO Diagnostic Tools Run
Click [Tools - VBO Diagnostic Tools] or Press F4 for the VBO system diagnosis
3
![Page 4: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/4.jpg)
VBO Diagnostic Tools Run
<VBO Diagnostic Tools Main Screen>
4
![Page 5: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/5.jpg)
VBO Diagnostic Tools Run
No Name Function
1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In, Arm Out, Bucket Crowd, Bucket Dump, Travel Right, Travel Left, Swing Pressure
2 Swash Plate Angle Check - Swash Plate Angle Check - Front pump Angle volt, Rear Pump Angle volt
3 EPPR V/V Check - EPPR V/V Check - Power Shift P/V 1, Power Shift P/V2
4 Main Pump Pressure Check
- Main Pump Pressure Check - Front Pump Pressure, Rear Pump Pressure
5 Relief Pressure Check - Relief Pressure Check - Front Pump Pressure, Rear Pump Pressure
5
![Page 6: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/6.jpg)
VBO Diagnostic Check List
Contents Reference Green Red
Max 30 bar Reference ↓ Reference ↑
Min 5 bar Reference ↓ Reference ↑
Rising Time (Min to Max)
0.5 sec Reference ↓ Reference ↑
Falling Time (Max to Min)
0.5 sec Reference ↓ Reference ↑
criteria Green Yellow Red
Max (4450 mV)
±10 mV +20mV -120mV
> Yellow
Min (600mV)
±10 mV +100mV -140mV
> Yellow
Rising Time (current(400
mA) to 4V) 1.2 sec Reference ↓ Reference ↑
Reference Green Yellow Red
100 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
200 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
300 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
500 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
700 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
800 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
850 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
Command (bar)
Reference(bar)
Green Yellow Red
45
±3
±25
>Yellow
100 ±24
200 ±22.5
250 ±21.5
300 ±21
350 ±20
Joystick Check List
Swash Plate Angle Check List
EPPR V/V Current Check List
Main Pump Pressure Check List
6
![Page 7: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/7.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
7
![Page 8: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/8.jpg)
1. Joystick Check
(3)
(1)
(2) (2)
(4)
No Name Function
(1) Test Contents • Select the Joystick Operation Test
(2) Graph • The graph displays real-time operation • Tests are marked with different colors
(3) Status Before the test
• Display The Engine RPM, Battery Voltage, Hydraulic Temp
(4) Status and results of tests
• Status of the Results of the operation - Minimum Pressure, Maximum Pressure - Up Time, Down Time. - Coloring for Pass / Fail
Joystick Check Screen Description
※ Test Result
Contents Reference Green Red
Max 30 bar Reference ↓ Reference ↑
Min 5 bar Reference ↓ Reference ↑
Up Time 0.5 sec Reference ↓ Reference ↑
Down Time 0.5 sec Reference ↓ Reference ↑
8
![Page 9: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/9.jpg)
1. Joystick Check
Pop-Up creation if doesn't check the Engine RPM ,safety lever
Pop-Up creation if doesn't check the safety lever
Pop-Up creation if the engine RPM is low
Settings before the test
Over Engine RPM1800 (Auto idle OFF)
Put the Safety lever up (Bypass Cut S/V Off)
Read the current fault information,
Check the pressure sensor failure
Settings before the Joystick Check test
Maintain the battery Voltage is 27.0V or more
Maintain the oil temperature is 20 degrees or more
9
![Page 10: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/10.jpg)
1. Joystick Check
Boom Up
Boom Down
Joystick Lever
<Boom Up Pressure[F1]>
STEP 1 – Select the Test
Click or press F1
STEP 2 – Tests performed actions
The progress of the Joystick Check test
Joystick Lever Boom Up Quickly
Return to neutral Waiting one second
10
![Page 11: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/11.jpg)
1. Joystick Check
STEP 3 – Display Test results and Status
<Boom Up Pressure[F1]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 11
The progress of the Joystick Check test
![Page 12: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/12.jpg)
1. Joystick Check
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
※ Etc.
1. Results Unit indicates until the second decimal point. 2. Sampling time is less than the 20 ms. 3. test result data subsequently can use the TMS server transfer function.
<Boom Up Pressure[F1]>
12
The progress of the Joystick Check test
![Page 13: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/13.jpg)
1. Joystick Check
Boom Up
Boom Down
Joystick Lever
<Boom Down Pressure[F2]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Return to neutral after waiting one second after Joystick Lever Boom Down Quickly
Click or press F2
Joystick Lever Boom Down Quickly
Return to neutral Waiting one second
13
The progress of the Joystick Check test
![Page 14: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/14.jpg)
1. Joystick Check
<Boom Down Pressure[F2]>
STEP 3 – Display Test results and Status
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 14
The progress of the Joystick Check test
![Page 15: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/15.jpg)
1. Joystick Check
<Boom Down Pressure[F2]>
STEP 4 – Move the test menu
Click at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
15
The progress of the Joystick Check test
![Page 16: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/16.jpg)
1. Joystick Check
Arm In
Arm
Out
Joystick Lever
<Arm In Pressure[F3]>
STEP 1 STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F3
Joystick Lever Arm In Quickly
Return to neutral Waiting one second
16
The progress of the Joystick Check test
![Page 17: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/17.jpg)
1. Joystick Check
<Arm In Pressure[F3]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
※ Shown in red on fail
Display the Status Test Results
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure
STEP 3 – Display Test results and Status
17
The progress of the Joystick Check test
![Page 18: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/18.jpg)
1. Joystick Check
STEP 4 – Move the test menu
<Arm In Pressure[F3]>
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
18
The progress of the Joystick Check test
![Page 19: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/19.jpg)
1. Joystick Check
Arm In
Arm Out
Joystick Lever
<Arm Out Pressure[F4]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F4
Joystick Lever Arm Out Quickly
Return to neutral Waiting one second
19
The progress of the Joystick Check test
![Page 20: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/20.jpg)
1. Joystick Check
<Arm Out Pressure[F4]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 20
The progress of the Joystick Check test
![Page 21: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/21.jpg)
1. Joystick Check
<Arm Out Pressure[F4]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
21
The progress of the Joystick Check test
![Page 22: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/22.jpg)
1. Joystick Check
Bucket Crowd
Bucket
Dump
Joystick Lever
<Bucket crowd Pressure[F5]>
STEP 2 – Tests performed actions
STEP 1 – Select the Test
Click or press F5
Joystick Lever Bucket Crowd Quickly
Return to neutral Waiting one second
22
The progress of the Joystick Check test
![Page 23: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/23.jpg)
1. Joystick Check
<Bucket crowd Pressure[F5]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 23
The progress of the Joystick Check test
![Page 24: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/24.jpg)
1. Joystick Check
<Bucket crowd Pressure[F5]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
24
The progress of the Joystick Check test
![Page 25: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/25.jpg)
1. Joystick Check
Bucket Crowd
Bucket
Dump
Joystick Lever
<Bucket Dump Pressure[F6]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F6
Joystick Lever Bucket Dump Quickly
Return to neutral Waiting one second
25
The progress of the Joystick Check test
![Page 26: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/26.jpg)
1. Joystick Check
<Bucket Dump Pressure[F6]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 26
The progress of the Joystick Check test
![Page 27: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/27.jpg)
1. Joystick Check
<Bucket Dump Pressure[F6]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
27
The progress of the Joystick Check test
![Page 28: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/28.jpg)
1. Joystick Check
Joystick Lever[Pedal]
<Travel Right Pressure[F7]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F7
Operate Joystick Lever[Pedal] Travel Right Quickly
Return to neutral Waiting one second
Travel Right
Travel Left
28
The progress of the Joystick Check test
![Page 29: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/29.jpg)
1. Joystick Check
<Travel Right Pressure[F7]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 29
The progress of the Joystick Check test
![Page 30: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/30.jpg)
1. Joystick Check
<Travel Right Pressure[F7]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
30
The progress of the Joystick Check test
![Page 31: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/31.jpg)
1. Joystick Check
Joystick Lever[Pedal]
<Travel Left Pressure[F8]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F8
Operate Joystick Lever[Pedal] Travel Left Quickly
Return to neutral Waiting one second
Travel Right
Travel Left
31
The progress of the Joystick Check test
![Page 32: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/32.jpg)
1. Joystick Check
<Travel Left Pressure[F8]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 32
The progress of the Joystick Check test
![Page 33: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/33.jpg)
1. Joystick Check
<Travel Left Pressure[F8]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
33
The progress of the Joystick Check test
![Page 34: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/34.jpg)
1. Joystick Check
Swing
Joystick Lever
<Swing Pressure[F9]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F9
Joystick Lever Swing Quickly
Return to neutral Waiting one second
34
The progress of the Joystick Check test
![Page 35: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/35.jpg)
1. Joystick Check
<Swing Pressure[F9]>
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure 35
The progress of the Joystick Check test
![Page 36: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/36.jpg)
1. Joystick Check
<Swing Pressure[F9]>
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
36
The progress of the Joystick Check test
![Page 37: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/37.jpg)
1. Joystick Check
Joystick Lever
<Arti Boom Up Pressure[F10]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F10
Joystick Lever[Pedal] Articulated Boom Up Quickly
Return to neutral Waiting one second Articulated Boom Up
Articulated Boom Down
37
The progress of the Joystick Check test
![Page 38: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/38.jpg)
1. Joystick Check
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure
<Arti Boom Up Pressure[F10]>
38
The progress of the Joystick Check test
![Page 39: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/39.jpg)
1. Joystick Check
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
<Arti Boom Up Pressure[F10]>
39
The progress of the Joystick Check test
![Page 40: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/40.jpg)
1. Joystick Check
Joystick Lever
<Arti Boom Down Pressure[F11]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F11
Joystick Lever[Pedal] Articulated Boom Down Quickly
Return to neutral Waiting one second Articulated Boom Up
Articulated Boom Down
40
The progress of the Joystick Check test
![Page 41: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/41.jpg)
1. Joystick Check
※ Criteria Minimum pressure: 5 bar ↓, Maximum pressure: 30 bar ↑ Quick Operation (0.5 sec ↓) Operating: 0 ~ 30 bar
Display the test progress
Display the Status Test Results
※ Shown in red on fail
STEP 3 – Display Test results and Status
Boom Up Pressure Bucket Crowd Pressure
Boom Down Pressure Bucket Dump Pressure
Arm In Pressure Travel Right Pressure
Arm Out Pressure Travel Left Pressure
Swing Pressure Arti Boom Up Pressure
Arti Boom Down Pressure
<Arti Boom Down Pressure[F11]>
41
The progress of the Joystick Check test
![Page 42: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/42.jpg)
1. Joystick Check
STEP 4 – Move the test menu
Click on at the end of the Joystick Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(Swash Plate Angle Check), Click Move to Swash Plate Angle Check
<Arti Boom Down Pressure[F11]>
42
The progress of the Joystick Check test
![Page 43: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/43.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
43
![Page 44: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/44.jpg)
2. Swash Plate Angle Check
No Name Function
(1) Test Contents • Select the Angle Check Test
(2) Graph • The graph displays real-time operation • Tests are marked with different colors
(3) Status Before the test
• Display The Engine RPM, Battery Voltage, Hydraulic Temp
(4) Status and results of tests
• Status of the Results of the operation - Minimum Pressure, Maximum Pressure - Up Time, Down Time. - Coloring for Pass / Fail • Shown in red on fail
(3)
(2) (2) (4)
(1)
Swash Plate Angle Check Screen Description
※ Results Min, Max Value(Refer Value) Conversion Time (Refer Time)
criteria Green Yellow Red
Max (4450 mV)
±10 mV +20mV -120mV
> Yellow
Min (600mV)
±10 mV +100mV -140mV
> Yellow
44
![Page 45: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/45.jpg)
Settings before the test
Joystick lever neutral
Under Engine RPM1000 (Auto idle OFF)
Put the Safety lever down (Bypass Cut S/V ON)
Maintain the battery Voltage is 27.0V or more
Maintain the oil temperature is 20 degrees or more
Pop-Up creation if doesn't check the safety lever
2. Swash Plate Angle Check
Settings before the Angle Check test Pop-Up creation if doesn't check the Engine RPM ,safety lever and Alternator voltage.
Pop-Up creation if the engine RPM is low
Pop-Up creation if doesn't check the Alternator voltage.
45
![Page 46: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/46.jpg)
<Front Pump Angle volt [F1]>
VBO diagnostic program will automatically run the Front Pump Angle Volt
2. Swash Plate Angle Check
The progress of the Angle Check test
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F1
46
![Page 47: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/47.jpg)
2. Swash Plate Angle Check
STEP 3 – Display Test results and Status
<Front Pump Angle volt [F1]>
The progress of the Angle Check test • Display the test progress
※ Criteria Min Voltage: 0.43V – 0.7V, Max Voltage: 4.33V - 4.47V Transition time(1.2sec , Forced Current (400mA) -> 4.0V))
• Display the Status Test Results
※ Results Min, Max Value(Refer Value) Conversion Time (Refer Time) Front Pump Angle Voltage
Rear Pump Angle Voltage criteria Green Yellow Red
Max (4450 mV)
±10 mV +20mV -120mV
> Yellow
Min (600mV)
±10 mV +100mV -140mV
> Yellow
47
![Page 48: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/48.jpg)
2. Swash Plate Angle Check
<Front Pump Angle volt [F1]>
STEP 4 – Move the test menu
The progress of the Angle Check test
Click on at the end of the Angle Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(EPPR V/V Check), Click Move to EPPR V/V Check
48
![Page 49: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/49.jpg)
<Rear Pump Angle volt [F2]>
2. Swash Plate Angle Check
STEP 1 – Select the Test
STEP 2 – Tests performed actions
The progress of the Angle Check test
Click or press F2
VBO diagnostic program will automatically run the Rear Pump Angle Volt
49
![Page 50: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/50.jpg)
2. Swash Plate Angle Check
<Rear Pump Angle volt [F2]>
STEP 3 – Display Test results and Status
The progress of the Angle Check test •Display the test progress
•Display the Status Test Results
※ Results Min, Max Value(Refer Value) Conversion Time (Refer Time) Front Pump Angle Voltage
Rear Pump Angle Voltage criteria Green Yellow Red
Max (4450 mV)
±10 mV +20mV -120mV
> Yellow
Min (600mV)
±10 mV +100mV -140mV
> Yellow
※ Criteria Min Voltage: 0.43V – 0.7V, Max Voltage: 4.33V - 4.47V Transition time(1.2sec , Forced Current (400mA) -> 4.0V))
50
![Page 51: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/51.jpg)
2. Swash Plate Angle Check
<Rear Pump Angle volt [F2]>
STEP 4 – Move the test menu
The progress of the Angle Check test
Click on at the end of the Angle Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test(EPPR V/V Check), Click Move to EPPR V/V Check
51
![Page 52: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/52.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
52
![Page 53: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/53.jpg)
3. EPPR V/V Check
No Name Function
(1) Test Contents • Select the EPPR V/V Check Test
(2) Graph • The graph displays real-time operation • Tests are marked with different colors
(3) Status Before the test
• Display The Engine RPM, Battery Voltage, Hydraulic Temp
(4) Status and results of tests
• Display The Engine RPM, Battery Voltage, Hydraulic Temp - Display to command , output, error for each command ※ Status
(3)
(1)
((2) 2)
(4)
EPPR V/V Check Screen Description
Reference Green Yellow Red
100 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
200 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
300 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
500 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
700 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
800 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
850 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
※ Status
53
![Page 54: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/54.jpg)
3. EPPR V/V Check
Settings before the test
Joystick lever neutral
Over Engine RPM 1800 (Start-up is ON)
Put the Safety lever down (Bypass Cut S/V ON)
Maintain the battery Voltage is 27.0V or more
Maintain the oil temperature is 20 degrees or more
Pop-Up creation if doesn't check the Engine RPM ,safety lever
Pop-Up creation if doesn't check the safety lever
Settings before the EPPR V/V Check test
54
![Page 55: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/55.jpg)
<Power Shift P/V 1[F1]>
3. EPPR V/V Check
The progress of the EPPR V/V Check test
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F1
VBO diagnostic program will automatically run the EPPR V/V Check
55
![Page 56: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/56.jpg)
※ Results - Display to command , output, error for each command ※ Status
3. EPPR V/V Check
<Power Shift P/V 1[F1]>
STEP 3 – Display Test results and Status
• Display the test progress
•Display the Status Test Results
The progress of the EPPR V/V Check test
Power Shift P/V 1
Power Shift P/V 2
Force Operation Command
Reference Green Yellow Red
100 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
200 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
300 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
500 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
700 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
800 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
850 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑ 56
![Page 57: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/57.jpg)
3. EPPR V/V Check
STEP 4 – Apply modified value
If you want to have to retake the modified values, click
Retest
STEP 5 – Retest results
Retested with the modified value (the test results confirmed changes)
Before Retest After Retest
Apply modified value
<Power Shift P/V 1[F1]>
The progress of the EPPR V/V Check test
57
![Page 58: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/58.jpg)
3. EPPR V/V Check
STEP 6 – Move the test menu
<Power Shift P/V 1[F1]>
The progress of the EPPR V/V Check test
Click on at the end of the EPPR V/V Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test (Main Pump Check ), Click Move to Main Pump Check
58
![Page 59: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/59.jpg)
3. EPPR V/V Check
<Power Shift P/V 2[F2]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
The progress of the EPPR V/V Check test
Click or press F2
VBO diagnostic program will automatically run the EPPR V/V Check
59
![Page 60: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/60.jpg)
3. EPPR V/V Check
<Power Shift P/V 2[F2]>
STEP 3 – Display Test results and Status
※ Results - Display to command , output, error for each command ※ Status
The progress of the EPPR V/V Check test • Display the test progress
•Display the Status Test Results
Power Shift P/V 1
Power Shift P/V 2
Force Operation Command
Reference Green Yellow Red
100 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
200 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
300 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
500 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
700 ± 3 mA ↓ ± 20 mA ↓ ± 20 mA ↑
800 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑
850 ± 5 mA ↓ ± 25 mA ↓ ± 25 mA ↑ 60
![Page 61: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/61.jpg)
3. EPPR V/V Check
Retest
Retested with the modified value (the test results confirmed changes)
Before Retest After Retest
<Power Shift P/V 2[F2]>
STEP 4 – Apply modified value
STEP 5 – Retest results
The progress of the EPPR V/V Check test
If you want to have to retake the modified values, click
Apply modified value
61
![Page 62: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/62.jpg)
3. EPPR V/V Check
<Power Shift P/V 2[F2]>
The progress of the EPPR V/V Check test
STEP 6 – Move the test menu
Click on at the end of the EPPR V/V Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test (Main Pump Check ), Click Move to Main Pump Check
62
![Page 63: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/63.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
63
![Page 64: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/64.jpg)
Pop-Up creation if doesn't check the Engine RPM ,safety lever
Pop-Up creation if the engine RPM is low
4. Main Pump Pressure Check
Settings before the test
Joystick lever neutral
Over Engine RPM1800 (Auto idle OFF)
Maintain the oil temperature is 40 degrees or more
Check before the test
Bypass Cut Valve Check
Pump Pressure Sensor Check
Solenoid valve
Pressure sensor
Settings before the Main Pump Pressure Check test
64
![Page 65: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/65.jpg)
No Name Function
(1) Test Contents • Select the Joystick Operation Test
(2) Graph • The graph displays real-time operation • Tests are marked with different colors
(3) Status Before the test
• Display The Engine RPM, Battery Voltage, Hydraulic Temp
(4) Status and results of tests
• Display The Engine RPM, Battery Voltage, Hydraulic Temp -Display to command , output, error for each command ※ Status
(3)
(1)
(2) (2)
(4)
4. Main Pump Pressure Check Main Pump Pressure Check Screen Description
Command (bar)
Reference(bar)
Green Yellow Red
45
±3
±25
>Yellow
100 ±24
200 ±22.5
250 ±21.5
300 ±21
350 ±20
※ Status
※(1) Hyd .Temp : pump pressure decreases by Raising the temperature
-> A reference temperature set to 40 ℃.
(2) Correction of error : Yellow, (Complex tolerance of the vehicle.
Set up to by each single Pump tolerance)
65
![Page 66: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/66.jpg)
<Front Pump Pressure [F1]>
4. Main Pump Pressure Check The progress of the Main Pump Pressure Check
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F1
VBO diagnostic program will automatically run the Main Pressure Check
66
![Page 67: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/67.jpg)
• Display the Status Test Results
• Display the test progress
※ Display to command , output, error for each command
4. Main Pump Pressure Check
<Front Pump Pressure [F1]>
STEP 3 – Display Test results and Status
The progress of the Main Pump Pressure Check
Front Pump Pressure
Rear Pump Pressure
Force Operation Command
Command (bar)
Reference(bar)
Green Yellow Red
45
±3
±25
>Yellow
100 ±24
200 ±22.5
250 ±21.5
300 ±21
350 ±20
※ Status
67
![Page 68: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/68.jpg)
STEP 4 - Apply modified value
Retest
STEP 5 - Move the test menu
4. Main Pump Pressure Check
<Front Pump Pressure [F1]>
If you want to have to retake the modified values, click
Click at the end of the Main Pump Pressure Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test (Relief Pressure Check), Click Move to Relief Pressure Check
The progress of the Main Pump Pressure Check
※Correction of error : Yellow, (Complex tolerance of the vehicle. Set up to by each single Pump tolerance)
68
![Page 69: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/69.jpg)
4. Main Pump Pressure Check
<Rear Pump Pressure [F2]>
STEP 1 – Select the Test
STEP 2 – Tests performed actions
The progress of the Main Pump Pressure Check
Click or press F1
VBO diagnostic program will automatically run the Main Pressure Check
69
![Page 70: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/70.jpg)
• Display the Status Test Results
• Display the test progress
4. Main Pump Pressure Check
STEP 3 – Display Test results and Status
<Rear Pump Pressure [F2]>
The progress of the Main Pump Pressure Check
※ Display to command , output, error for each command
Front Pump Pressure
Rear Pump Pressure
Force Operation Command
Command (bar)
Reference(bar)
Green Yellow Red
45
±3
±25
>Yellow
100 ±24
200 ±22.5
250 ±21.5
300 ±21
350 ±20
※ Status
70
![Page 71: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/71.jpg)
4. Main Pump Pressure Check
<Rear Pump Pressure [F2]>
The progress of the Main Pump Pressure Check
STEP 4 - Apply modified value
Retest
STEP 5 - Move the test menu
If you want to have to retake the modified values, click
Click on at the end of the Main Pump Pressure Check Go to the VBO Diagnostic Tools Main Screen
In order to check the next Test (Relief Pressure Check), Click Move to Relief Pressure Check
※Correction of error : Yellow, (Complex tolerance of the vehicle. Set up to by each single Pump tolerance)
71
![Page 72: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/72.jpg)
Contents
1. Joystick Check
2. Angle Check
3. EPPR V/V Check
4. Main Pressure Check
5. Relief Pressure Check
72
![Page 73: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/73.jpg)
5. Relief Pressure Check Settings before the Relief Pressure Check Test
Pop-Up creation if doesn't check the Engine RPM ,safety lever
Pop-Up creation if the engine RPM is low
Settings before the test
Joystick lever neutral
Over Engine RPM1800 (Auto idle OFF)
Maintain the oil temperature is 40 degrees or more
Check before the test
Bypass Cut Valve Check
Pump Pressure Sensor Check
Solenoid valve
Pressure sensor
73
![Page 74: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/74.jpg)
No Name Function
(1) Test Contents • Select the Joystick Operation
Test
(2) Graph • The graph displays real-time operation • Tests are marked with different colors
(3) Status Before the test
• Display The Engine RPM, Battery Voltage, Hydraulic Temp
(4) Status and results of tests
• Status of the test operation - Reference(350Bar) Swash Plate Tilting Angle , Leakage and Relief Pressure
(3)
(1)
(2(2) )
(4)
5. Relief Pressure Check Relief Pressure Check Screen Description
74
![Page 75: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/75.jpg)
5. Relief Pressure Check
<Front Pump Pressure [F1]>
The progress of the Main Pump Pressure Check Test
STEP 1 – Select the Test
STEP 2 – Tests performed actions
Click or press F1
VBO diagnostic program will automatically run the Relief Pressure Check
75
![Page 76: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/76.jpg)
5. Relief Pressure Check
•Display the Status Test Results
※ Results - Reference(350Bar) Swash Plate Tilting Angle , Leakage and Relief Pressure
• Display the test progress
<Front Pump Pressure [F1]>
STEP 3 – Display Test results and Status
The progress of the Main Pump Pressure Check Test
Front Pump Pressure
Rear Pump Pressure
Front Pump Swash-plate angle Voltage
Rear Pump Swash-plate angle Voltage
76
![Page 77: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/77.jpg)
5. Relief Pressure Check
STEP 4 – Move the test menu
<Front Pump Pressure [F1]>
The progress of the Main Pump Pressure Check Test
Click on at the end of the Relief Pressure Check Go to the VBO Diagnostic Tools Main Screen
77
![Page 78: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/78.jpg)
5. Relief Pressure Check
<Rear Pump Pressure [F2]>
STEP 1 STEP 1 – Select the Test
STEP 2 – Tests performed actions
The progress of the Main Pump Pressure Check Test
Click or press F2
VBO diagnostic program will automatically run the Relief Pressure Check
78
![Page 79: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/79.jpg)
5. Relief Pressure Check
Display the Status Test Results
※ Results - Reference(350Bar) Swash Plate Tilting Angle , Leakage and Relief Pressure
• Display the test progress
<Rear Pump Pressure [F2]>
STEP 3 – Display Test results and Status
The progress of the Main Pump Pressure Check Test
Front Pump Pressure
Rear Pump Pressure
Front Pump Swash-plate angle Voltage
Rear Pump Swash-plate angle Voltage
79
![Page 80: VBO Diagnostic Tools Manual (DX350LC-3/DX380LC-3)autocd.info/VBOManualEn.pdf · 1 Joystick Check - Check the pressure depending on joystick operation - Boom Up, Boom Down, Arm In,](https://reader035.vdocuments.us/reader035/viewer/2022071403/60f72a79874122172f0c1ff0/html5/thumbnails/80.jpg)
5. Relief Pressure Check
<Rear Pump Pressure [F2]>
STEP 4 – Move the test menu
Click on at the end of the Relief Pressure Check Go to the VBO Diagnostic Tools Main Screen
The progress of the Main Pump Pressure Check Test
E.O.D. 80