vayo-nexim accelerator (vfna) quick guide data source: asm ... vayo-nexim accelerator 4/19 3. flow...

Vayo-Nexim Accelerator (VFNA)

Quick Guide

Data Source: ASM Program (*.sipro,*.xml)

Version: V1.0 Data updated: 2017/12/27

www.vayoinfo.com

http://www.vayoinfo.com/

Vayo-Nexim Accelerator

www.vayoinfo.com 2/19

Table of Contents

1. About Vayo-Nexim Accelerator ........................................ 3

2. Data Source Requirement ............................................... 3

3. Flow Chart (Step by step guide) ...................................... 4

3.1. Default work flow chart: .............................................................................. 4

3.2. Explanation of Flow Chat ............................................................................ 4

3.3. Required procedures for ASM’s program data source ................................ 6

4. How to generate Nexim job with ASM’s program ............ 7

4.1. Create New Vayo Job with program input .................................................. 7

4.2. Gerber Import (Optional) ........................................................................... 10

4.3. Mark Setting (Optional) ............................................................................. 10

4.4. Part Data Editor (Optional) ....................................................................... 11

4.5. PCB Orientation Setting (Optional) ........................................................... 12

4.6. Parts Verification (Optional) ...................................................................... 13

4.7. Generate Nexim Job ................................................................................. 14

5. How to get support ......................................................... 19




1. About Vayo-Nexim Accelerator

Vayo-Nexim Accelerator (VFNA) software accelerates Nexim programming with intelligent, automatic & no-brainer approach. Nexim Accelerator enables Nexim to import varies PCB CAD/Gerber & BOM, SMT Programs; utilizes design information in maximum; intelligently match existing part data & create new part data; automatic correct parts angle & position; generate output directly to Nexim Job. It leverages the whole placement programming process, which reduce programming cycle reduce machine occupy time to new product introduction. Therefore it saves manufacturing and labor cost.

2. Data Source Requirement

Data source: 2.1: ASM/SiPlace’s program which is from Siplace pro programming system of ASM 2.2: Sample data is located at: \Vayo-Nexim Accelerator\Data\SampleData\3_ASM_Program

2.2.1: Sipro File: Vayo1152084.sipro 2.2.2: XML File: N011360-PANEL_B.xml

How to export ASM’s program from Siplace Pro system: 1) Open SIPLACE Pro Desk software, select the desired output of the program in Job Tree View, or

Recipe Tree View interface, right-select "Data Model Export ...";

2) Select the output path, click "Save". (“*.Sipro” is the format of output program with version of Pro

V7.0 or higher than Pro V7.0, “* xml” is the format of output program with version lower than Pro V7.0.)

Note: If the picture is used to infringe the copyright owners, please notify us in time, I will promptly delete!




3. Flow Chart (Step by step guide)

3.1. Default work flow chart:

Note:

1. There are total 11 steps according to diffirent data source input;

2. For Gerber Input step,it’s optional according to your data source,if you import pcb CAD or SMT program data, maybe you need to skip this step.

3. It supports to customized flow chart if needed, but get Vayo’s support.

3.2. Explanation of Flow Chat

A step by step flow chart is offered to ease the operation (Ctrl+F1 to show flow chart if close); the default flow chart appears as below: Flow chart file name: VFA-process-EN.txt, or refer below picture:




1 - Flow chart name; 2 - Flag upon the step has already been accomplished; 3 - Step name; 4 - Function button (Click to execute this step.); 5 - Help information (Instructions for selected step).

Note: To switch to different flow chat, go to menu Process-> Select Process Flow.

3.3. Required procedures for ASM’s program data source

1. Create new job with program input step 1: Program Import

2. Import Gerber layer for reference (Optional) step 2: Gerber Import

3. Confirm or set Mark point (Optional) step 7: Mark Setting

4. Smart to assign PD and correct angle for parts: step 5: Part Data Editor

6. Set PCB reflow orientation: step 6: PCB Board Orientation

7. Finally verify PD/Polarity/Position of parts: step 8: Parts Verification

8. Generate Nexim Job: step 9: Generate Nexim Job to Nexim System

1

2

3

4

5




step 10: Generate Nexim Job to Hard Disk.

4. How to generate Nexim job with ASM’s program

4.1. Create New Vayo Job with program input

Menu: File->New Job To start a new project, you must create a Vayo Job firstly; all inputs shall be saved to this Job. 1) File-> New Job, or click on below icon to create a new Job;

2) Click “Select Files” to select program file, and it will auto give job name based on file name;




Note: if it does NOT identify the CAD/program format, please select the corresponding format

manually from the CAD/program Interface list. 3) Click “Import” to parse selected program and popup window:

4) Select one of list.

a. Select one recipe of list, If there is no recipe, please confirm the data source is right (VFNA only

support program exported by job and recipe). b. Tick “Add prefix “skip_” for skip components: skip_xxx” according to your need. c. Click “Load” to parse program data.




d. Click “Close” when you see “End!” from message box. 5) Click “Next” to save the inputted program data to the Job if graphic is correct.

To main Interface:




4.2. Gerber Import (Optional)

Note: Generally, Don’t need to do this step. You can import Gerber layer for reference if needed. Flow chart: Gerber Import Menu: Process-> Gerber&XY Import -> Gerber Import Please refer details of Gerber Import from manual “Vayo-Nexim Accelerator Quick Guide-EN-V1.0.pdf”

4.3. Mark Setting (Optional)

Note: Generally, Don’t need to do this step. The program must contain fiducial marks, if you want to double check them, please click this step to validate marks as below: Flow chart: Mark Setting Menu: Graphical-> Mark Origin-> Create Mark Shortcut Key: R




If there isn’t any mark, please do “Mark Setting” step to set fiducial marks for SMT/Placement program. Please refer details of Mark Setting from manual “Vayo-Nexim Accelerator Quick Guide-EN-V1.0.pdf”

4.4. Part Data Editor (Optional)

Note: Generally, Don’t need to do this step. You can double validate/re-assign part data if needed. Flow chart: Part Data Editor Menu: Process-> Part Data Editor




If you need to re-assign part data or package to Part number, please refer details of “Part data editor” section from manual “Vayo-Nexim Accelerator Quick Guide-EN-V1.0.pdf”

4.5. PCB Orientation Setting (Optional)

Note: Generally, don’t need to do this step. If you need to change the orientation, please do following procedure. Flow chart: PCB Board orientation Menu: Graphical-> PCB Orientation Setting




4.6. Parts Verification (Optional)

Note: Generally, Don’t need to do this step. You can double verify it, or import Gerber layers for reference. Flow chart: Parts Verification Menu: Process-> Parts Verification




Please refer details of Parts Verification from manual “Vayo-Nexim Accelerator Quick Guide-EN-V1.0.pdf”

4.7. Generate Nexim Job

Flow chart: Export Job To System Menu: Process-> Export Job to System-> Export Job to System Output the Job to Nexim directly When you first output Nexim job, please click ”Connect to Nexim” to set database connection, refer to 5.4.3 Nexim Connection Setting in “Vayo-Nexim Accelerator Quick Guide-EN-V1.0.pdf” Then select Job group, and assign Job name and its version, and click “OK”




Options setting for generation:




Note: please select options according to your needs.

Click “Output”




Once the output is completed successfully, you shall see the Job in Nexim Job list. Note: you might need to press shortcut key F5 to refresh the Job list in Nexim.




Flow chart: Export Job To Hard Disk Menu: Process-> Export Job to System-> Export Job to Disk

Output the Job to local disk:

If Accelerator is installed offline, then you can output a Nexim Job to your local disk and then copy and input it to Nexim system.




5. How to get support

You can contact your local vendor to get support or send an email to [email protected] Contact Information: Vayo (Shanghai) Technology Co., Ltd. Phone: +86-21-61182128 Email: [email protected] Visit us at www.vayoinfo.com


mailto:[email protected]


vayo-nexim accelerator (vfna) quick guide data source: asm ... vayo-nexim accelerator 4/19 3. flow...

Documents