vauxhall viva owner's manual...or front or back, always relate to the direction of travel....

Vauxhall VivaOwner's Manual

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 31Storage ........................................ 49Instruments and controls ............. 56Lighting ........................................ 88Climate control ............................. 94Driving and operating ................. 103Vehicle care ............................... 131Service and maintenance .......... 169Technical data ........................... 172Customer information ................ 183Index .......................................... 190

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.Disregarding the description given inthis manual may affect your warranty.

When this Owner's Manual refers to aworkshop visit, we recommend yourVauxhall Authorised Repairer.For gas vehicles, we recommend aVauxhall Authorised Repairerlicensed to service gas vehicles.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual● This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to modelvariant, country specifications,special equipment oraccessories.

● The "In brief" section will give youan initial overview.

● The table of contents at thebeginning of this manual andwithin each section shows wherethe information is located.

● The index will enable you tosearch for specific information.

● This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drivevehicles.

● The Owner's Manual uses theengine identifier code. Thecorresponding sales designationcan be found in the section"Technical data".

● Directional data, e.g. left or right,or front or back, always relate tothe direction of travel.

● Displays may not support yourspecific language.

● Display messages and interiorlabelling are written in boldletters.

4 Introduction

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Page references and index entriesrefer to the indented headings givenin the section table of content.Chronological order to select menuentries in the vehicle personalisationis indicated with I.Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press c to unlock the doors and loadcompartment. Open the doors bypulling the handles.

To open the tailgate, push the switchon the underside of the brandemblem.Radio remote control 3 20, Centrallocking system 3 21, Loadcompartment 3 24.

In brief 7

Seat adjustmentLongitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.Seat position 3 32, Seat adjustment3 33.

Backrest inclination

Pull lever, adjust inclination andrelease lever. Allow the seat toengage audibly.Seat position 3 32, Seat adjustment3 33.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Seat position 3 32, Seat adjustment3 33.

8 In brief

Head restraint adjustment

Press release button, adjust heightand engage.Head restraints 3 31.

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25 °).To release belt, press red button onbelt buckle.Seat position 3 32, Seat belts3 35, Airbag system 3 37.

Mirror adjustmentInterior mirror

To adjust the mirror, move the mirrorhousing in the desired direction.Manual anti-dazzle interior mirror3 27.

In brief 9

Exterior mirrors

Select the relevant exterior mirror andadjust it.Exterior mirrors 3 26, Electricadjustment 3 26, Folding exteriormirrors 3 26.Heated exterior mirrors 3 26.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 37, Ignitionpositions 3 104.

10 In brief

Instrument panel overview

In brief 11

1 Power windows ..................... 28

Central locking system .......... 212 Exterior mirrors ..................... 263 Cruise control ..................... 119

Speed limiter ...................... 121Heated steering wheel .......... 57

4 Turn and lane-changesignals, headlight flash,low beam and high beam ...... 90

Exit lighting ........................... 93

Parking lights ........................ 915 Side air vents ...................... 1006 Instruments .......................... 617 Driver Information Centre ...... 738 Steering wheel controls ....... 579 Windscreen wiper,

windscreen washersystem, rear windowwiper, rear window washersystem ................................... 58

10 Centre air vents .................. 10011 Hazard warning flashers ...... 8912 Info-Display ........................... 78

13 Anti-theft alarm systemstatus LED ........................... 25

14 Infotainment system15 Glovebox .............................. 4916 Climate control system .......... 9417 AUX input, USB input18 Selector lever, manual

transmission ....................... 110Selector lever, manualtransmission automated ...... 111

19 Seat heating .......................... 3420 Parking brake ...................... 11521 Ignition switch with

steering wheel lock ............ 10422 Horn ..................................... 58

Driver airbag ........................ 4023 Bonnet release lever .......... 13324 Steering wheel adjustment . . 5725 Fuse box ............................ 14726 Traction Control system ..... 116

City mode ............................ 118Stop-start system ................ 106Fuel selector ......................... 63Lane departure warning ..... 123

Electronic Stability Control . 11727 Light switch .......................... 88

Headlight rangeadjustment ........................... 89Front fog light ........................ 90Rear fog light ........................ 90

Brightness of instrumentpanel illumination .................. 91

12 In brief

Exterior lightingLight switch

Turn light switch:7 : lights off8 : sidelights9 : headlights

Fog lightsPress button in light switch:> : front fog lights

r : rear fog light

Headlight flash, high beam andlow beam

headlight flash : pull leverhigh beam : push leverlow beam : push or pull lever

High beam 3 88, Headlight flash3 88.

Turn and lane-change signals

lever up : right turn signallever down : left turn signal

Turn and lane-change signals3 90, Parking lights 3 91.

In brief 13

Hazard warning flashers

Operated by pressing ¨.Hazard warning flashers 3 89.

Horn

Press j.

Washer and wiper systemsWindscreen wiper

HI : fastLO : slowE : interval wipingOFF : off

For single wipe when the wiper is off,press lever down to position 2.Windscreen wiper 3 58.

14 In brief

Windscreen washer

Pull lever.Windscreen washer system 3 58,Washer fluid 3 135, Wiper bladereplacement 3 138.

Rear window wiper

Press the rocker switch to activate therear window wiper:upper switch : continuous

operationlower switch : intermittent

operationmiddle position : off

Rear window washer

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.Rear window wiper/washer 3 59.

In brief 15

Climate controlHeated rear window

The heating is operated by pressingÜ.Heated rear window 3 29.

Heated exterior mirrorsPressing Ü also activates the heatedexterior mirrors.Heated exterior mirrors 3 26.

Demisting and defrosting thewindows

● Press V.● Set temperature control to

warmest level.● Set fan speed to highest level.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

Climate control system 3 94.

TransmissionManual transmission

Reverse: with the vehicle stationary,depress clutch pedal and press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 110.

16 In brief

Manual transmission automated

R : reverse, engage only whenvehicle is stationary

N : neutralD : automatic modeM : manual mode< : upshift in manual mode] : downshift in manual mode

Manual transmission automated3 111.

Starting offCheck before starting off● Tyre pressure and condition

3 150, 3 182.● Engine oil level and fluid levels

3 134.● All windows, mirrors, exterior

lighting and number plates arefree from dirt, snow and ice andare operational.

● Proper position of mirrors, seats,and seat belts 3 26, 3 32,3 36.

● Brake function at low speed,particularly if the brakes are wet.

Starting the engine

● Turn key to position 1.● Move the steering wheel slightly

to release the steering wheellock.

● Manual transmission: operateclutch and brake pedal.Manual transmission automated:operate brake pedal.Automatic transmission: operatebrake pedal and move selectorlever to P or N.

● Do not operate accelerator pedal.● Turn key to position 3 and

release.

In brief 17

Starting the engine 3 105. Stop-start system

If the vehicle is at a low speed or at astandstill and certain conditions arefulfilled, activate an Autostop asfollows:

Vehicles with manual transmission:● Depress the clutch pedal.● Set the lever to neutral.● Release the clutch pedal.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.To restart the engine, depress theclutch pedal again.

Vehicles with manual transmissionautomated:If the vehicle is at a standstill with thebrake pedal depressed, Autostop isactivated automatically, indicated bythe needle at the AUTOSTOPposition in the tachometer.Release the brake pedal or moveselector lever out of D to restart theengine.Stop-start system 3 106.

18 In brief

Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the manualparking brake without pressingthe release button. Apply asfirmly as possible on a downhillslope or uphill slope. Depressbrake pedal at the same time toreduce operating force.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear before removing theignition key. On an uphill slope,turn the front wheels away fromthe kerb.If the vehicle is on a downhillslope, engage reverse gearbefore removing the ignition

key. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. Turn thesteering wheel until thesteering wheel lock is felt toengage.

For vehicles with manualtransmission automated, the keycan only be removed from theignition switch when the parkingbrake is applied.

● Lock the vehicle by pressing e onthe radio remote control.Activate the anti-theft alarmsystem 3 25.

● The engine cooling fans may runafter the engine has beenswitched off 3 133.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a lowload or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

Keys, locks 3 19, Laying-up thevehicle for a long period of time3 132.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Keys .......................................... 19Radio remote control ................. 20Memorised settings ................... 21Central locking system .............. 21Child locks ................................. 23

Doors ........................................... 24Load compartment .................... 24

Vehicle security ............................ 25Anti-theft alarm system .............. 25Immobiliser ................................ 25

Exterior mirrors ............................ 26Mirrors ....................................... 26Electric adjustment .................... 26Folding mirrors .......................... 26Heated mirrors ........................... 26

Interior mirrors ............................. 27Manual anti-dazzle .................... 27

Windows ...................................... 27Windscreen ............................... 27Manual windows ........................ 27Power windows ......................... 28

Heated rear window .................. 29Sun visors .................................. 29

Roof ............................................. 29Sunroof ...................................... 29

Keys, locksKeys

Caution

Do not attach heavy or bulky itemsto the ignition key.

Replacement keysThe key number is specified in theCar Pass or on a detachable tag.The key number must be quotedwhen ordering replacement keys, asit is a component of the immobilisersystem.Locks 3 166.The code number of the adapter forthe locking wheel bolts is specified ona card. It must be quoted whenordering a replacement adapter.Wheel changing 3 159.

20 Keys, doors and windows

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key and then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Radio remote control

Used to operate:● central locking system● anti-theft alarm system

The radio remote control has a rangeof approx. 20 metres. It can berestricted by external influences. Thehazard warning flashers confirmoperation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:● The range is exceeded.● The battery voltage is too low.● Frequent, repeated operation of

the radio remote control while notin range, which will require re-synchronisation.

● Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time.

● Interference from higher-powerradio waves from other sources.

Unlocking 3 21.

Radio remote control batteryreplacementReplace the battery as soon as therange reduces.


Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Key with foldaway key section

Extend the key and open the unitsideways. Replace the battery(battery type CR 2032), payingattention to the installation position.Close the unit and synchronise.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when the ignition isswitched on.

Memorised settingsWhenever the key is removed fromthe ignition switch, the followingsettings are automatically memorisedby the key:● lighting● presets for Infotainment system● central locking system● comfort settings

The saved settings are automaticallyused the next time the memorised keyis inserted into the ignition switch andturned to position 1 3 104.A precondition is that PersonalizationBy Driver is activated in the personalsettings of the Info-Display.This must be set for each key used.Vehicle personalisation 3 82.

Central locking systemUnlocks and locks doors and loadcompartment.NoticeIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.

Unlocking

Press c.


Two settings are selectable in theInfo-Display:● To unlock only the driver's door,

press c once. To unlock all doorsand load compartment, press ctwice.

● Press c once to unlock all doorsand load compartment.

The setting can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 82.The setting can be saved for the keybeing used.Memorised settings 3 21.

LockingClose doors, load compartment andfuel filler flap.

Press e.If the driver's door is not closedproperly, the central locking systemwill not work.

Central locking buttonsLocks or unlocks doors and the loadcompartment from inside thepassenger compartment.

Press e to lock.Press c to unlock.


Fault in radio remote controlsystem

Unlocking

Manually unlock the driver's door byturning the key in the lock. Switch onthe ignition and press the centrallocking button c to unlock the otherdoors and load compartment.By switching on the ignition, the anti-theft alarm system is deactivated.

LockingClose all doors. Open the driver'sdoor and press the central lockingbutton. The vehicle is locked.

Close the driver's door. Manually lockthe driver's door by turning the key.

Fault in central locking system

UnlockingManually unlock the driver's door byturning the key in the lock. From theinside of the vehicle the doors can beunlocked by pulling up the lock buttonon the respective door. The loadcompartment cannot be unlocked.

Automatic door lockingIf no door is opened or the position ofignition key is not located in position1 or position 2 within three minutesafter unlocking with the radio remotecontrol, all the doors are locked andthe anti-theft alarm system isactivated automatically.

Child locks

9 Warning

Use the child locks wheneverchildren are occupying the rearseats.

Move the pin in the rear door to thefront. The door cannot be openedfrom inside.


DoorsLoad compartmentTailgate

Opening

To open the tailgate, push the switchon the underside of the brandemblem.

Closing

Use interior handle.Do not press the touchpad switchwhilst closing as this will unlock thetailgate again.Central locking system 3 21.

General hints for operatingtailgate

9 Danger

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaust

gases, which cannot be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate, checkoverhead obstructions, e.g. agarage door, to avoid damage tothe tailgate. Always check themoving area above and behind thetailgate.

NoticeThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.


Vehicle securityAnti-theft alarm systemThe anti-theft alarm system iscombined with the central lockingsystem.It monitors:● doors, tailgate, bonnet● ignition

Status LED

Status LED is integrated in the sensoron top of the instrument panel.

Status during the first 30 seconds ofanti-theft alarm system activation:LED illuminates : test, arming delayLED flashesquickly

: doors, tailgate orbonnet notcompletely closed,or system fault

Seek the assistance of a workshop inthe event of faults.

DeactivationUnlocking the vehicle by pressing cdeactivates anti-theft alarm system.

AlarmWhen triggered, the alarm hornsounds and the hazard warning lightsflash simultaneously. The numberand duration of alarm signals arestipulated by legislation.The alarm can be silenced bypressing any button on the radioremote control or by switching on theignition.The anti-theft alarm system can onlybe deactivated by pressing c on theradio remote control or by switchingon the ignition.

Vehicle messages 3 79.

ImmobiliserThe system is part of the ignitionswitch and checks whether thevehicle is allowed to be started withthe key being used.The immobiliser is activatedautomatically after the key has beenremoved from the ignition switch.If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and repeat thestart attempt.If the control indicator continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.NoticeThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it.Switch on the anti-theft alarmsystem 3 21, 3 25.

Control indicator d 3 72.


Exterior mirrorsMirrorsThe shape of the mirrors makesobjects appear smaller, which willaffect the ability to estimatedistances.

Electric adjustment

Select the relevant exterior mirror byturning the control to left (L) or right(R). Then swivel the control to adjustthe mirror.In position 0 no mirror is selected.

Folding mirrorsFor pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.

Heated mirrors

Operated by pressing Ü.Mirror heating works with the enginerunning.It is switched off automatically after ashort time.


Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.

WindowsWindscreenWindscreen stickersDo not attach stickers, e.g. toll roadstickers or similar, on the windscreenin the area of the interior mirror.Otherwise the detection zone of thesensor in the mirror housing could berestricted.

Windscreen replacement

Caution

If the vehicle has a front-lookingcamera sensor for the driverassistance systems, it is veryimportant that any windscreenreplacement is performedaccurately according to Vauxhallspecifications. Otherwise, thesesystems may not work properlyand there is a risk of unexpectedbehaviour and/or messages fromthese systems.

Manual windows

The windows can be opened orclosed manually with the windowcranks.


Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.Be careful when closing thewindows. Ensure that nothingbecomes trapped in them as theymove.

Operable with ignition on (position 2)3 104.Retained power off 3 105.

Operate the switch in the door trim forthe respective window by pushing toopen or pulling to close.

OpenShort push: window opens in stages.Long push: window opensautomatically up to end position. Tostop movement, move switch inopposite direction.

CloseShort pull: window closes in stages.Longer pull: window closesautomatically up to end position. Tostop movement, move switch inopposite direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, switch on theignition, then pull the switch severaltimes to close the windows in stages.

Child safety system for rearwindows

Press z to deactivate rear doorpower windows; the LED illuminates.To activate, press z again.


OverloadIf the windows are repeatedlyoperated at short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be opened orclosed automatically (e.g. afterdisconnecting the vehicle battery),activate the window electronics asfollows:1. Close the doors.2. Switch on ignition.3. Close the window completely and

operate the button for anadditional two seconds.

4. Repeat this procedure for eachwindow.

Heated rear window

Operated by pressing Ü.Rear window heating works with theengine running.It is switched off automatically after ashort time.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.The integral mirrors should be closedwhen driving.

RoofSunroof

9 Warning

Take care when operating thesunroof. Risk of injury, particularlyto children.Keep a close watch on themovable parts when operatingthem. Ensure that nothingbecomes trapped in them as theymove.

Operable via a rocker switch withignition on (position 2) 3 104.Retained power off 3 105.


RaiseHold switch p depressed until thesunroof is raised at the rear.

OpenFrom raised position press andrelease switch p: the sunroof isopened automatically up to endposition. To stop movement beforeend position, operate switch oncemore.

CloseHold switch r depressed from anyposition until sunroof is closedcompletely. Releasing the switchstops movement in any position.NoticeIf the top of the roof is wet, tiltsunroof, allow water to run off andthen open sunroof.

Do not affix any stickers to sunroof.

SunblindThe sunblind is manually operated.Close or open the sunblind by sliding.When the sunroof is open, thesunblind is always open.

Seats, restraints 31

Seats, restraints

Head restraints ............................ 31Front seats ................................... 32

Seat position .............................. 32Seat adjustment ........................ 33Heating ...................................... 34

Seat belts ..................................... 35Three-point seat belt ................. 36

Airbag system .............................. 37Front airbag system ................... 40Side airbag system .................... 41Curtain airbag system ............... 41Airbag deactivation .................... 42

Child restraints ............................. 43Child restraint systems .............. 43Child restraint installationlocations ................................... 45

ISOFIX child restraint systems . . 48Top-tether fastening eyes .......... 48

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Front head restraints, heightadjustment

Press release button, adjust height,engage.

32 Seats, restraints

Rear head restraints, heightadjustment

Pull the head restraint upwards andlet engage. To move downwards,press the catch to release and pushthe head restraint downwards.

Removal of rear head restraintE.g. when using a child restraintsystem 3 43.

Press both catches, pull the headrestraint upwards and remove.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

9 Warning

Never store any objects under theseats.


● Sit with buttocks as far backagainst the backrest as possible.Adjust the distance between theseat and the pedals so that legsare slightly angled when fullypressing the pedals. Slide thefront passenger seat as far backas possible.

● Set seat height high enough tohave a clear field of vision on allsides and of all displayinstruments. There should be atleast one hand of clearancebetween head and the roofframe. Your thighs should restlightly on the seat withoutpressing into it.

● Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Donot angle the backrest too farback. We recommend amaximum rake of approx. 25°.

● Adjust seat and steering wheel ina way that the wrist rests on topof the steering wheel while thearm is fully extended andshoulders on the backrest.

● Adjust the steering wheel 3 57.● Adjust the head restraint 3 31.● Adjust the seat belt 3 36.

Seat adjustmentDrive only with engaged seats andbackrests.

Longitudinal adjustment

Pull handle, slide seat, releasehandle. Try to move the seat back andforth to ensure that the seat is lockedin place.


Backrest inclination

Pull lever, adjust inclination andrelease lever. Allow the backrest toengage audibly.

Seat height

Lever pumping motionup : seat higherdown : seat lower

Heating

Activate seat heating by pressing ßfor the respective front seat.The LED in the button illuminates toindicate activation.Pressing ß once more deactivatesseat heating.Seat heating is operational whenengine is running.During an Autostop, seat heating isalso operational.Stop-start system 3 106.


Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle holding the occupants inthe sitting position. Therefore the riskof injury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. Childrestraint system 3 43.Periodically check all parts of the beltsystem for damage, pollution andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoticeMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or are trapped. Prevent dirtfrom getting into the belt retractors.

Seat belt reminderFront seats are equipped with a seatbelt reminder, indicated for driver seatas control indicator X in thetachometer 3 68, and for frontpassenger seat as control indicatork in the Driver Information Centre3 65.

Belt force limitersStress on the body is reduced by thegradual release of the belt during acollision.

Belt pretensionersIn the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by continuous illuminationof control indicator v 3 68.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.NoticeDo not affix or install accessories orother objects that may interfere withthe operation of the beltpretensioners. Do not make any


modifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.

Three-point seat beltFasten

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into thebuckle. Tighten the lap belt regularlywhile driving by pulling the shoulderbelt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Seat belt reminder X 3 68.

Unfasten

To release belt, press red button onbelt buckle.


Using the seat belt while pregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Airbag systemThe airbag system consists of anumber of individual systemsdepending on the scope ofequipment.When triggered, the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

NoticeThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not affix any objects onto theairbag covers and do not cover themwith other materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it may be

necessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate escaping hotgases may cause burns.

FaultIf there is a fault in the airbag system,the control indicator v illuminates anda message or a warning codeappears in the Driver InformationCentre. The system is notoperational.Have the cause of the fault remediedby a workshop.Control indicator for airbag systems3 68.


Child restraint systems on frontpassenger seat with airbagsystems

EN: NEVER use a rearward-facingchild restraint on a seat protected byan ACTIVE AIRBAG in front of it;DEATH or SERIOUS INJURY to theCHILD can occur.DE: Nach hinten gerichteteKindersitze NIEMALS auf einem Sitzverwenden, der durch einen davorbefindlichen AKTIVEN AIRBAGgeschützt ist, da dies den TOD oderSCHWERE VERLETZUNGEN DESKINDES zur Folge haben kann.

FR: NE JAMAIS utiliser un sièged'enfant orienté vers l'arrière sur unsiège protégé par un COUSSINGONFLABLE ACTIF placé devant lui,sous peine d'infliger desBLESSURES GRAVES, voireMORTELLES à l'ENFANT.ES: NUNCA utilice un sistema deretención infantil orientado haciaatrás en un asiento protegido por unAIRBAG FRONTAL ACTIVO. Peligrode MUERTE o LESIONES GRAVESpara el NIÑO.RU: ЗАПРЕЩАЕТСЯустанавливать детскоеудерживающее устройство лицомназад на сиденье автомобиля,оборудованном фронтальнойподушкой безопасности, еслиПОДУШКА НЕ ОТКЛЮЧЕНА! Этоможет привести к СМЕРТИ илиСЕРЬЕЗНЫМ ТРАВМАМРЕБЕНКА.NL: Gebruik NOOIT een achterwaartsgericht kinderzitje op een stoel meteen ACTIEVE AIRBAG ervoor, omDODELIJK of ERNSTIG LETSEL vanhet KIND te voorkomen.

DA: Brug ALDRIG en bagudvendtautostol på et forsæde med AKTIVAIRBAG, BARNET kan komme iLIVSFARE eller komme ALVORLIGTTIL SKADE.SV: Använd ALDRIG en bakåtvändbarnstol på ett säte som skyddas meden framförvarande AKTIV AIRBAG.DÖDSFALL eller ALLVARLIGASKADOR kan drabba BARNET.FI: ÄLÄ KOSKAAN sijoita taaksepäinsuunnattua lasten turvaistuintaistuimelle, jonka edessä onAKTIIVINEN TURVATYYNY, LAPSIVOI KUOLLA tai VAMMAUTUAVAKAVASTI.NO: Bakovervendtbarnesikringsutstyr må ALDRI brukespå et sete med AKTIVKOLLISJONSPUTE foran, da det kanføre til at BARNET utsettes forLIVSFARE og fare for ALVORLIGESKADER.PT: NUNCA use um sistema deretenção para crianças voltado paratrás num banco protegido com umAIRBAG ACTIVO na frente do


mesmo, poderá ocorrer a PERDA DEVIDA ou FERIMENTOS GRAVES naCRIANÇA.IT: Non usare mai un sistema disicurezza per bambini rivoltoall'indietro su un sedile protetto daAIRBAG ATTIVO di fronte ad esso:pericolo di MORTE o LESIONIGRAVI per il BAMBINO!EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικόκάθισμα ασφαλείας με φορά προς ταπίσω σε κάθισμα που προστατεύεταιαπό μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,διότι το παιδί μπορεί να υποστείΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟΤΡΑΥΜΑΤΙΣΜΟ.PL: NIE WOLNO montować fotelikadziecięcego zwróconego tyłem dokierunku jazdy na fotelu, przedktórym znajduje się WŁĄCZONAPODUSZKA POWIETRZNA.Niezastosowanie się do tegozalecenia może być przyczynąŚMIERCI lub POWAŻNYCHOBRAŻEŃ u DZIECKA.TR: Arkaya bakan bir çocuk emniyetsistemini KESİNLİKLE önünde birAKTİF HAVA YASTIĞI ilekorunmakta olan bir koltukta

kullanmayınız. ÇOCUK ÖLEBİLİRveya AĞIR ŞEKİLDEYARALANABİLİR.UK: НІКОЛИ не використовуйтесистему безпеки для дітей, щовстановлюється обличчям назад,на сидінні з УВІМКНЕНОЮПОДУШКОЮ БЕЗПЕКИ, інакше цеможе призвести до СМЕРТІ чиСЕРЙОЗНОГО ТРАВМУВАННЯДИТИНИ.HU: SOHA ne használjon hátrafelénéző biztonsági gyerekülést előlrőlAKTÍV LÉGZSÁKKAL védett ülésen,mert a GYERMEK HALÁLÁT vagyKOMOLY SÉRÜLÉSÉT okozhatja.HR: NIKADA nemojte koristiti sustavzadržavanja za djecu okrenut premanatrag na sjedalu s AKTIVNIMZRAČNIM JASTUKOM ispred njega,to bi moglo dovesti do SMRTI iliOZBILJNJIH OZLJEDA za DIJETE.SL: NIKOLI ne nameščajte otroškegavarnostnega sedeža, obrnjenega vnasprotni smeri vožnje, na sedež zAKTIVNO ČELNO ZRAČNOBLAZINO, saj pri tem obstajanevarnost RESNIH ali SMRTNIHPOŠKODB za OTROKA.

SR: NIKADA ne koristiti bezbednosnisistem za decu u kome su decaokrenuta unazad na sedištu saAKTIVNIM VAZDUŠNIMJASTUKOM ispred sedišta zato štoDETE može da NASTRADA ili da seTEŠKO POVREDI.MK: НИКОГАШ не користете детскоседиште свртено наназад наседиште заштитено со АКТИВНОВОЗДУШНО ПЕРНИЧЕ пред него,затоа што детето може ДА ЗАГИНЕили да биде ТЕШКО ПОВРЕДЕНО.BG: НИКОГА не използвайтедетска седалка, гледаща назад,върху седалка, която е защитеначрез АКТИВНА ВЪЗДУШНАВЪЗГЛАВНИЦА пред нея - може дасе стигне до СМЪРТ илиСЕРИОЗНО НАРАНЯВАНЕ наДЕТЕТО.RO: Nu utilizaţi NICIODATĂ un scaunpentru copil îndreptat spre partea dinspate a maşinii pe un scaun protejatde un AIRBAG ACTIV în faţa sa;acest lucru poate duce la DECESULsau VĂTĂMAREA GRAVĂ aCOPILULUI.


CS: NIKDY nepoužívejte dětskýzádržný systém instalovaný protisměru jízdy na sedadle, které jechráněno před sedadlem AKTIVNÍMAIRBAGEM. Mohlo by dojít kVÁŽNÉMU PORANĚNÍ nebo ÚMRTÍDÍTĚTE.SK: NIKDY nepoužívajte detskúsedačku otočenú vzad na sedadlechránenom AKTÍVNYM AIRBAGOM,pretože môže dôjsť k SMRTI aleboVÁŽNYM ZRANENIAM DIEŤAŤA.LT: JOKIU BŪDU nemontuokite atgalatgręžtos vaiko tvirtinimo sistemossėdynėje, prieš kurią įrengta AKTYVIORO PAGALVĖ, nes VAIKAS GALIŽŪTI arba RIMTAI SUSIŽALOTI.LV: NEKĀDĀ GADĪJUMĀneizmantojiet uz aizmuguri vērstubērnu sēdeklīti sēdvietā, kas tiekaizsargāta ar tās priekšā uzstādītuAKTĪVU DROŠĪBAS SPILVENU, jopretējā gadījumā BĒRNS var gūtSMAGAS TRAUMAS vai IET BOJĀ.ET: ÄRGE kasutage tahapoolesuunatud lapseturvaistet istmel, milleees on AKTIIVSE TURVAPADJAGA

kaitstud iste, sest see võibpõhjustada LAPSE SURMA võiTÕSISE VIGASTUSE.MT: QATT tuża trażżin għat-tfal lijħares lejn in-naħa ta’ wara fuq sitprotett b’AIRBAG ATTIV quddiemu;dan jista’ jikkawża l-MEWT jewĠRIEĦI SERJI lit-TFAL.Beyond the warning required byECE R94.02, for safety reasons aforward-facing child restraint systemmust only be used subject to theinstructions and restrictions in thetables 3 45.The airbag label is located on bothsides of the front passenger sun visor.Airbag deactivation 3 42.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. The location isidentified by the word AIRBAG.The front airbag system is triggered inthe event of a front-end impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position.Seat position 3 32.Keep the area in which the airbaginflates clear of obstructions.


Fit the seat belt correctly andengage securely. Only then is theairbag able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.The location is identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoticeOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. The location is identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of a side-on impact of acertain severity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event of aside-on impact considerably.


9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks on the handles in theroof frame are only suitable forhanging up light articles ofclothing, without coat hangers. Donot keep any items in theseclothes.

Airbag deactivationThe front passenger airbag systemmust be deactivated for a childrestraint system on the passengerseat according to the instructions inthe tables 3 45.The other airbag systems, the beltpretensioners and all driver airbagsystems will remain active.

Use the ignition key to choose theswitch position:*OFF : front passenger airbag is

deactivated and will notinflate in the event of acollision. Control indicator*OFF illuminatescontinuously

VON : front passenger airbag isactive

9 Danger

Deactivate passenger airbag onlyin combination with the use of achild restraint system, subject tothe instructions and restrictions inthe tables 3 45.Otherwise, there is a risk of fatalinjury for a person occupying aseat with a deactivated frontpassenger airbag.


If control indicator d illuminates forapprox. 60 seconds after the ignitionis switched on, the front passengerairbag system will inflate in the eventof a collision.If both control indicators areilluminated at the same time, there isa system failure. The status of thesystem is not discernible, thereforeno person is allowed to occupy thefront passenger seat. Contact aworkshop immediately.Change status only when the vehicleis stopped with the ignition off.Status remains until the next change.Control indicator for airbagdeactivation 3 68.

Child restraintsChild restraint systemsWe recommend Vauxhall childrestraint systems which are tailoredspecifically to the vehicle.The following child restraints arerecommended for the followingweight classes:● Group 0, Group 0+

Maxi Cosi Cabriofix with ISOFIXbase, for children up to 13 kg

● Group IDuo Plus with ISOFIX and Toptether, for children from 9 kg to18 kg in this group

● Group II, Group IIIKidfix with or without ISOFIX forchildren from 15 kg to 36 kg

When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.

Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

9 Danger

If using a rear-facing child restraintsystem on the front passengerseat, the airbag system for thefront passenger seat must bedeactivated. This also applies tocertain forward-facing childrestraint systems as indicated inthe tables 3 45.

Airbag deactivation 3 42.Airbag label 3 37.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This ensures that the child'sbackbone, which is still very weak, isunder less strain in the event of anaccident.


Only use suitable restraint systems,e.g. those that comply with validUN ECE regulations.Ensure that the child restraint systemto be installed is compatible with thevehicle type. Refer to the tables onthe following pages, the instructionssupplied with the child restraintsystem and the vehicle type list ofnon-universal child restraint systems.Ensure that the mounting location ofthe child restraint system within thevehicle is correct, see followingtables.Remove rear head restraint beforemounting a child restraint system ifrequired.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.Child restraint systems could befastened with ISOFIX mountingbrackets, Top-tether if available,and/or a three-point seat belt. Referto the following tables.

NoticeDo not affix anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.


Child restraint installation locationsPermissible options for fastening a child restraint system with a three-point seat belt

Weight and age classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1 U2 X

Group 0+: up to 13 kgor approx. 2 years

X U1 U2 X

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1 U2 X

Group II: 15 to 25 kgor approx. 3 to 7 years

X X U2 X

Group III: 22 to 36 kgor approx. 6 to 12 years

X X U2 X

U : universal suitability in conjunction with three-point seat beltX : no child restraint system permitted in this weight class1 : adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt runs forwards from

the upper anchorage point2 : move the driver and/or passenger seat forwards and adjust seat backrest inclination as far as necessary to a vertical

position to ensure that the child restraint system does not have any interference from the front seat backrest.


Permissible options for fitting an ISOFIX child restraint system

Weight class Size class FixtureOn front passenger

seatOn rear outboard

seats On rear centre seat

Group 0: up to 10 kgor approx. 10 months

F ISO/L1 X X X

G ISO/L2 X X X

E ISO/R1 X IL X

Group 0+: up to 13 kgor approx. 2 years

E ISO/R1 X IL X

D ISO/R2 X IL X

C ISO/R3 X IL1 X

Group I: 9 to 18 kgor approx. 8 months to 4 years

D ISO/R2 X IL X

C ISO/R3 X IL1 X

B ISO/F2 X IL, IUF X

B1 ISO/F2X X IL, IUF X

A ISO/F3 X IL, IUF X

Group II: 15 to 25 kgor approx. 3 to 7 years

X IL X

Group III: 22 to 36 kgor approx. 6 to 12 years

X IL X


IL : suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or "semi-universal" categories.The ISOFIX restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the childrestraint system)

IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight classX : no ISOFIX child restraint system approved for this weight class1 : only applicable for rear outer seat on passenger side with foremost seating position and backrest upright.

NoticeMove the driver and/or passenger seat forwards and adjust seat backrest inclination as far as necessary to a verticalposition to ensure that the child restraint system does not have any interference from the front seat backrest.

ISOFIX size class and seat deviceA – ISO/F3 : forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kgB – ISO/F2 : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgB1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kgC – ISO/R3 : rear-facing child restraint system for children of maximum size in the weight class up to 18 kgD – ISO/R2 : rear-facing child restraint system for smaller children in the weight class up to 18 kgE – ISO/R1 : rear-facing child restraint system for young children in the weight class up to 13 kgF - ISO/L1 : left lateral facing position CRS (carry cot) for smaller children in the weight class up to 10 kgG - ISO/L2 : right lateral facing position CRS (carry cot) for smaller children in the weight class up to 10 kg.


ISOFIX child restraintsystemsFasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the table byIL.

ISOFIX mounting brackets on therear seats are indicated by theISOFIX logo on the backrest.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.

Remove rear head restraint beforemounting a child restraint system, ifrequired 3 31.Route, attach, and tighten the toptether according to your child restraintinstructions.

Top-tether fastening eyesThe vehicle has two fastening eyeson the back of the rear seats.Top-tether fastening eyes are markedwith the symbol : for a child seat.

In addition to the ISOFIX mounting,fasten the Top-tether strap to theTop-tether fastening eyes.

Route, attach, and tighten the toptether according to your child restraintinstructions.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.Remove rear head restraint beforemounting a child restraint system, ifrequired 3 31.

Storage 49

Storage

Storage compartments ................ 49Glovebox ................................... 49Cupholders ................................ 49Centre console storage ............. 50

Load compartment ....................... 50Load compartment cover ........... 52Rear floor storage cover ............ 53Warning triangle ........................ 53First aid kit ................................. 54

Loading information ..................... 54

Storage compartments

9 Warning

Do not store heavy or sharpobjects in the storagecompartments. Otherwise, thestorage compartment lid couldopen and vehicle occupants couldbe injured by objects being thrownaround in the event of hardbraking, a sudden change indirection or an accident.

Glovebox

Pull lever to open the glovebox cover.The glovebox features an adapter forthe locking wheel bolts.The glovebox should be closed whilstdriving.

Cupholders

Cupholders are located in the centreconsole.

50 Storage

Centre console storage

The storage is used for small articles.

Load compartment

Load compartment extension

Caution

First fold up the rear seat cushionbefore folding the rear seatbackrest.Disregard may lead to damage tothe rear seat.

NoticeTo ensure sufficient room for rearseat cushion operation, slide thefront seats forward and move thefront seat backrest upright.

1. Pull up the front of the rear seatcushion to release it.

2. Guide the rear of the rear seatcushion to an upright position.

3. Remove the rear seat headrestraints 3 31.

Storage 51

4. Pull the release knob on top of therear backrest.

5. Fold down the backrest and insertthe rear seat head restraints intothe pockets.

6. Put the seat belts for the outboardseats into the belt guides.

7. Adjust the front seats to thedesired position.

To return the backrest to the originalposition:1. Lift the backrest up and pull out

the seat belt from the belt guides.Push backrest firmly into place.

9 Warning

When folding up, ensure thatbackrests are securely engaged inposition before driving. Failure todo so may result in personal injury

or damage to the load or vehicle inthe event of hard braking or acollision.

Ensure the seat belts are notpinched by the latch.

2. Reinstall the rear head restraints.3. Place the rear part of the seat

cushion in its original position.NoticeMake sure the seat belts are nottwisted or caught under the seatcushion.4. Push the front part of the seat

cushion down firmly until itlatches.

The centre rear seat belt may lockwhen you raise the backrest. If thishappens, allow the belt to go back allthe way and repeat operation.If the seat belt is still locked, fold downthe seat cushion and try again.To return the rear seat cushion, putthe rear part of the seat cushion in itsoriginal position ensuring that theseat belt buckle straps are not twisted

52 Storage

or caught under the seat cushion,then push the front part of the seatcushion firmly down until it latches.

Caution

When returning rear seat backrestto the upright position, place therear seat belt and bucklesbetween the rear seat backrestand one cushion. Make sure therear seat belt and buckles do notget pinched under the rear seatcushion.Ensure the seat belts are nottwisted or caught in the seatbackrest and are arranged in theirproper position.

To remove the rear seat cushion,push the hinges in direction of arrow.

Load compartment coverDo not place heavy objects on thecover.

RemovingUnhook retaining straps from tailgate.Lift cover at the rear and push itupwards at the front.Remove the cover.

StowingWhen the load compartment is fullyloaded, stow the load compartmentcover on the rear seats or removefrom vehicle.

FittingEngage cover in side guides and folddownwards. Attach retaining straps totailgate.

Storage 53

Rear floor storage coverRear floor cover

Lift up rear floor cover to gain accessto the tyre repair kit, vehicle tools andwarning triangle.On versions with spare wheel, thespare wheel is located under the rearfloor cover together with the vehicletools.Tools 3 149.

General hint

9 Warning

For safety reasons, stow all partsin the load compartment in itsposition, always drive with aclosed rear floor cover and, ifpossible, with folded up rearbackrests.Otherwise, vehicle occupantscould be injured by objects beingthrown around in the event ofsharp braking, a sudden change indirection or an accident.

Warning triangleVehicles with spare wheel

Stow the warning triangle in the loadcompartment.

54 Storage

Vehicles with tyre repair kit

Stow the warning triangle in thevehicle tool box below the floor overin the load compartment.

First aid kit

Stow the first-aid kit in the well in theload compartment.

Loading information● Heavy objects in the load

compartment should be placedagainst the seat backrests.Ensure that the backrests aresecurely engaged. If objects canbe stacked, heavier objectsshould be placed at the bottom.

● Secure loose objects in the loadcompartment to prevent themfrom sliding.

● When transporting objects in theload compartment, the backrestsof the rear seats must not beangled forward.

● Do not allow the load to protrudeabove the upper edge of thebackrests.

● Do not place any objects on theload compartment cover or theinstrument panel, and do notcover the sensor on top of theinstrument panel.

● The load must not obstruct theoperation of the pedals, parkingbrake and gear selector lever, or

Storage 55

hinder the freedom of movementof the driver. Do not place anyunsecured objects in the interior.

● Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or vehicle.

● The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 173) and the EC kerbweight.To calculate the payload, enterthe data for your vehicle in theweights table at the front of thismanual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (fueltank 90% full).

Optional equipment andaccessories increase the kerbweight.

● Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has adetrimental effect on vehiclehandling due to the vehicle'shigher centre of gravity.Distribute the load evenly andsecure it properly with retainingstraps. Adjust the tyre pressureand vehicle speed according tothe load conditions. Check andretighten the straps frequently.

56 Instruments and controls

Instruments andcontrols

Controls ....................................... 57Steering wheel adjustment ........ 57Steering wheel controls ............. 57Heated steering wheel ............... 57Horn ........................................... 58Windscreen wiper/washer ......... 58Rear window wiper/washer ....... 59Outside temperature .................. 59Clock ......................................... 59Power outlets ............................. 61Cigarette lighter ......................... 61Ashtrays .................................... 61

Warning lights, gauges and indi‐cators ........................................... 61

Instrument cluster ...................... 61Speedometer ............................. 61Odometer .................................. 62Trip odometer ............................ 62Tachometer ............................... 62Fuel gauge ................................ 62Fuel selector .............................. 63Engine coolant temperaturegauge ....................................... 64

Service display .......................... 64

Control indicators ...................... 65Turn signal ................................. 67Seat belt reminder ..................... 68Airbag and belt tensioners ......... 68Airbag deactivation .................... 68Charging system ....................... 69Malfunction indicator light .......... 69Service vehicle soon ................. 69Brake and clutch system ........... 69Operate pedal ............................ 69Antilock brake system (ABS) ..... 70Gear shifting .............................. 70Power steering .......................... 70Lane departure warning ............ 70Ultrasonic parking assist ........... 70Electronic Stability Control off . . . 70Electronic Stability Control andTraction Control system ........... 70

Traction Control system off ....... 71Engine coolant temperature ...... 71Tyre pressure monitoringsystem ...................................... 71

Engine oil pressure .................... 71Low fuel ..................................... 72Immobiliser ................................ 72Reduced engine power ............. 72Exterior light .............................. 72High beam ................................. 72Fog light ..................................... 72Rear fog light ............................. 72

Cruise control ............................ 72Speed limiter ............................. 72Bonnet open .............................. 72Door open .................................. 73

Information displays ..................... 73Driver Information Centre .......... 73Info display ................................ 78

Vehicle messages ........................ 79Warning chimes ......................... 81Battery voltage .......................... 81

Vehicle personalisation ................ 82OnStar ......................................... 84

Instruments and controls 57

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

Driver Information Centre, somedriver assistance systems,Infotainment system and a connectedmobile phone can be operated via thecontrols on the steering wheel.Driver assistance systems 3 119.Further information is available in theInfotainment manual.

Heated steering wheel

Activate heating by pressing A.Activation is indicated by the LED inthe button.


The grip areas of the steering wheelare heated quicker and to a highertemperature than the other areas.Heating is operational when theengine is running and during anAutostop.Stop-start system 3 106.

Horn

Press j.

Windscreen wiper/washerWindscreen wiper

HI : fastLO : slowE : interval wipingOFF : off

For a single wipe when thewindscreen wiper is off, press thelever down to position 2.Do not use if the windscreen is frozen.Switch off in car washes.

Windscreen washer

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.Washer fluid 3 135


Rear window wiper/washer

Press the rocker switch to activate therear window wiper:upper position : continuous

operationlower position : intermittent

operationmiddle position : off

Push lever. Washer fluid is sprayedonto the rear window and the wiperwipes a few times.Do not use if the rear window isfrozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Washer fluid 3 135Vehicle personalisation 3 82.

Outside temperatureA drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above 0°C.

ClockDate and time are shown in theInfo-Display.Info-Display 3 78


Graphic-Info-DisplayPress MENU to open the respectiveaudio menu.

Select Time and Date.

Set TimeSelect Set Time to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjusthours and minutes.Repeatedly select 12-24 HR at thebottom of the screen to choose a timemode.If the 12-hour mode is selected, athird column for AM and PM selectionis displayed. Select the desiredoption.

Set DateSelect Set Date to enter therespective submenu.Select Auto Set at the bottom of thescreen. Activate either On - RDS orOff (Manual).If Off (Manual) is selected, adjust thedate settings.

7'' Colour-Info-DisplayPress ; and then select Settings.Select Time and Date to display therespective submenu.

Set Time FormatTo select the desired time format,touch the screen buttons 12 h or 24 h.

Set Date FormatTo select the desired date format,select Set Date Format and choosebetween the available options in thesubmenu.

Auto SetTo choose whether time and date areto be set automatically or manually,select Auto Set.For time and date to be setautomatically, select On - RDS.For time and date to be set manually,select Off - Manual. If Auto Set is setto Off - Manual, the submenu itemsSet Time and Set Date becomeavailable.

Set time and dateTo adjust the time and date settings,select Set Time or Set Date.Touch + and - to adjust the settings.


Power outlets

A 12 Volt power outlet is located in thecentre console.Do not exceed the maximum powerconsumption of 120 watts.With ignition off, the power outlet isdeactivated. Additionally, the poweroutlet is deactivated in the event oflow vehicle battery voltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.

Do not connect any current-deliveringaccessories, e.g. electrical chargingdevices or batteries.Do not damage the outlet by usingunsuitable plugs.Stop-start system 3 106.

Cigarette lighterThe cigarette lighter may be locatedin the centre console.Press in cigarette lighter. It switchesoff automatically once the element isglowing. Pull out lighter.

Ashtrays

Caution

To be used only for ash and not forcombustible rubbish.

The portable ashtray can be placed inthe cupholders.

Warning lights, gaugesand indicatorsInstrument clusterThe needles of the instruments brieflyrotate to the end position when theignition is switched on.

Speedometer

Indicates vehicle speed.


Odometer

The bottom line displays the recordeddistance in miles.

Trip odometerThe recorded distance is displayedsince the last reset.Trip odometer counts up to9999.9 miles and then restarts at 0.To reset, press SET/CLR on the turnsignal lever for a few seconds3 73.

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Number of LEDs displays the level inthe fuel tank.The arrow indicates the vehicle sidewhere the fuel filler flap is located.During liquid gas operation, the levelin the gas tank is displayed.


Control indicator Y illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.During liquid gas operation, thesystem automatically switches over topetrol operation when gas tanks areempty 3 63.Never run the fuel tank dry.Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Fuel selector

Press LPG to switch between petroland liquid gas operation. The LED inthe button shows the currentoperating mode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

As soon as the liquid gas tank isempty, petrol operation isautomatically engaged until theignition is switched off.Fuel for liquid gas operation 3 125.


Engine coolant temperaturegauge

Number of LEDs displays the coolanttemperature.up to 2 LEDs : engine operating

temperature notyet reached

3 to 6 LEDs : normal operatingtemperature

more than 6LEDs

: temperature toohigh

Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system lets youknow when to change the engine oiland filter. Based on drivingconditions, the interval at which anengine oil and filter change will beindicated can vary considerably.

The remaining engine oil life durationis displayed in percent in the DriverInformation Centre.To display the remaining engine oillife duration use turn signal leverbuttons:

Press MENU to select the VehicleInformation Menu .Turn the adjuster wheel to selectRemaining Oil Life.


ResetPress SET/CLR on turn signal leverfor several seconds to reset. Theremaining engine oil life durationmenu must be active. Switch onignition, but not the engine.The system must be reset every timethe engine oil is changed to ensureproper functionality. Seek theassistance of a workshop.

Next serviceWhen the system has calculated thatengine oil life has diminished, awarning message appears in theDriver Information Centre. Haveengine oil and filter changed by aworkshop within one week or300 miles (whichever occurs first).Driver Information Centre 3 73.Service information 3 169.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions.

Depending on the equipment, theposition of the control indicators mayvary. When the ignition is switchedon, most control indicators willilluminate briefly as a functionalitytest.The control indicator colours mean:red : danger, important reminderyellow : warning, information, faultgreen : confirmation of activationblue : confirmation of activationwhite : confirmation of activation


Control indicators in the instrument cluster


Control indicators in the overheadconsole

Overview

O Turn signal 3 67

X Seat belt reminder 3 68

v Airbag and belt tensioners3 68

V Airbag deactivation 3 68

p Charging system 3 69

Z Malfunction indicator light3 69

g Service vehicle soon 3 69

R Brake and clutch system3 69

- Operate pedal 3 69

u Antilock brake system (ABS)3 70

[ Upshift 3 70

c Power steering 3 70

) Lane departure warning 3 70

r Ultrasonic parking assist3 70

a Electronic Stability Control off3 70

b Electronic Stability Control andTraction Control system 3 70

k Traction Control system off3 71

W Engine coolant temperature3 71

w Tyre pressure monitoringsystem 3 71

I Engine oil pressure 3 71

Y Low fuel 3 72

d Immobiliser 3 72

# Reduced engine power 3 72

8 Exterior light 3 72

C High beam 3 72

> Fog light 3 72

r Rear fog light 3 72

m Cruise control 3 72

L Speed limiter 3 72

/ Bonnet open 3 72

N Door open 3 73

Turn signalO illuminates or flashes green.

Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.


Rapid flashing: failure of a turn signallight or associated fuse.Bulb replacement 3 138, Fuses3 144.Turn signals 3 90.

Seat belt reminderSeat belt reminder on front seatsX for driver's seat illuminates orflashes red in the speedometer.

k for front passenger seat illuminatesor flashes red in the overheadconsole when the seat is occupied.

IlluminatesAfter the ignition has been switchedon, until the seat belt has beenfastened.

FlashesAfter having started the engine, for amaximum of 100 seconds, until theseat belt has been fastened.Fastening the seat belt 3 36.

Seat belt status on rear seatsX in the Driver Information Centreflashes or illuminates.

IlluminatesAfter having started the engine for aminimum of 35 seconds, until the seatbelt has been fastened.

FlashesAfter starting-off, when the seat belt isunfastened.Fastening the seat belt 3 36.

Airbag and belt tensionersv illuminates red.

When the ignition is switched on, thecontrol indicator illuminates forapprox. four seconds. If it does notilluminate, does not go out afterfour seconds or illuminates whilstdriving, there is a fault in the airbagsystem. Seek the assistance of aworkshop. The airbags and beltpretensioners may fail to trigger in theevent of an accident.Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.

9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Belt pretensioners, airbag system3 35, 3 37.

Airbag deactivationd illuminates yellow.The front passenger airbag isactivated.c illuminates yellow.


The front passenger airbag isdeactivated 3 42.

9 Danger

Risk of fatal injury for a child usinga child restraint system togetherwith activated front passengerairbag.Risk of fatal injury for an adultperson with deactivated frontpassenger airbag.

Charging systemp illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningStop, switch off engine. Vehiclebattery is not charging. Enginecooling may be interrupted. Thebrake servo unit may cease to beeffective. Seek the assistance of aworkshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Seek the assistance of aworkshop immediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Service vehicle soong illuminates yellow.Additionally, a warning code isdisplayed in the Driver InformationCentre.The vehicle requires a service.

Seek the assistance of a workshop.Vehicle messages 3 79.

Brake and clutch systemR illuminates red.The brake and clutch fluid level is toolow, when manual parking brake isnot applied 3 136.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates when the manual parkingbrake is applied and ignition isswitched on 3 115.

Operate pedal- illuminates or flashes yellow.

IlluminatesClutch pedal must be depressed tostart the engine in Autostop mode.Stop-start system 3 106.


FlashesPedal must be depressed for a mainstart of the engine 3 16, 3 105.

Antilock brake system(ABS)u illuminates yellow.Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator extinguishes.If the control indicator does not go outafter a few seconds, or if it illuminateswhile driving, there is a fault in theABS. The brake system remainsoperational but without ABSregulation.Antilock brake system 3 114.

Gear shifting[ with the number of therecommended gear is indicated,when upshifting is recommended forfuel saving reasons.

Power steeringc illuminates yellow.

Illuminates with power steeringdisabledFailure in the power steering system.Consult a workshop.

Illumination of c and bsimultaneouslyPower steering system must becalibrated, system calibration 3 118.

Lane departure warning) illuminates green or flashes yellow.

Illuminates greenSystem is switched on and ready tooperate.

Flashes yellowSystem recognises an unintendedlane change.Lane departure warning 3 123.

Ultrasonic parking assistr illuminates yellow.Fault in systemorFault due to sensors that are dirty orcovered by ice or snoworInterference due to external sourcesof ultrasound. Once the source ofinterference is removed, the systemwill operate normally.Have the cause of the fault in thesystem remedied by a workshop.Ultrasonic parking assist 3 122.

Electronic Stability Controlofft illuminates yellow.The system is deactivated.

Electronic Stability Controland Traction Control systemb flashes or illuminates yellow.


FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.

IlluminatesA fault in the system is present. Awarning code appears in the DriverInformation Centre. Continued drivingis possible. The system is notoperational. Driving stability,however, may deteriorate dependingon road surface conditions.Have the cause of the fault remediedby a workshop.Electronic Stability Control 3 117,Traction Control system 3 116.

Traction Control system offk illuminates yellow.The system is deactivated.

Engine coolant temperatureW illuminates red.

Illuminates when the engine isrunningStop, switch off engine.

Caution

Coolant temperature too high.

Check coolant level 3 135.If there is sufficient coolant, consult aworkshop.

Tyre pressure monitoringsystemw illuminates or flashes yellow.

IlluminatesTyre pressure loss. Stop immediatelyand check tyre pressure.

FlashesFault in system or tyre withoutpressure sensor mounted (e.g. sparewheel). After 60-90 seconds thecontrol indicator illuminatescontinuously. Consult a workshop.

Tyre pressure monitoring system3 151.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress the clutch.2. Set selector lever to neutral.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off the ignition.


9 Warning

When the engine is off,considerably more force is neededto brake and steer.During an Autostop, the brakeservo unit will still be operational.Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seeking theassistance of a workshop 3 134.

Low fuelY illuminates or flashes yellow.

IlluminatesLevel in fuel tank is too low.

FlashesFuel used up. Refuel immediately.Never run the fuel tank dry.Refuelling 3 127.Catalytic converter 3 110.

Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.

Reduced engine power# illuminates yellow.The engine power is limited. Consulta workshop.

Exterior light8 illuminates green.The exterior lights are on 3 88.

High beamC illuminates blue.Illuminated when high beam is on orduring headlight flash 3 88.

Fog light> illuminates green.The front fog lights are on 3 90.

Rear fog lightr illuminates yellow.The rear fog light is on 3 90.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenCruise control is active.Cruise control 3 119.

Speed limiterL illuminates in the DriverInformation Centre when Speedlimiter is active. Set speed is indicatedalongside L symbol.Speed limiter 3 121.

Bonnet open/ illuminates yellow.Illuminates when the bonnet is open.Stop-start system 3 106.


Door openN illuminates.A door or the tailgate is open.

Information displaysDriver Information CentreThe Driver Information Centre islocated in the instrument cluster.

Some of the displayed functions differwhen the vehicle is being driven or ata standstill. Some functions are onlyavailable when the vehicle is beingdriven.Main menus are:● trip/fuel information, see

description below● vehicle information, see

description below

The following indications appearwhen appropriate:● warning codes 3 79● gear shift indication 3 70● tyre pressure warning 3 151● seat belt reminder indication

3 68● service information 3 69

Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.


Press MENU to switch between themain menus or to return from asubmenu to the next higher menulevel.

Turn the adjuster wheel to select asubmenu of the main menu or to seta numeric value.

Press SET/CLR to select a function orto confirm a message.Vehicle and service messages arepopped-up in the Driver InformationCentre if required. Confirm messagesby pressing SET/CLR. Vehiclemessages 3 79.

Trip/Fuel informationPossible pages are:

Trip odometer

Trip odometer displays the currentdistance since a certain reset.Trip odometer counts up to9999 miles and then restarts at 0.To reset, press SET/CLR for a fewseconds.


Fuel range

Range is calculated from current fueltank level and current consumption.The display shows average values.After refuelling, the range is updatedautomatically after a brief delay.When the fuel level in the tank is low,a message appears on the displayand control indicator Y in the fuelgauge illuminates.When the tank must be refuelledimmediately, a warning code appearsand remains on the display.Additionally, control indicator Yflashes in the fuel gauge 3 72.

Fuel range, LPG versionDisplay of the approximate total fuelrange for each fuel tank (LPG andpetrol).

Average vehicle speed

Display of average speed. Themeasurement can be reset at anytime.To reset, press SET/CLR for a fewseconds while viewing this page.

Instantaneous fuel economy

Display of the instantaneousconsumption.On vehicles with LPG engines:Instantaneous consumption isindicated for the currently selectedmode, LPG or petrol.


Average fuel economy

Display of average consumption. Themeasurement can be reset at anytime and starts with a default value.To reset, press SET/CLR for a fewseconds while viewing this page.On vehicles with LPG engines:Average consumption is indicated forthe currently selected mode, LPG orpetrol.

Timer

Indicates driving time since last reset.To stop or start timer pressSET/CLR.To reset press and hold SET/CLR fora few seconds.

Vehicle informationPossible pages are:● unit● remaining engine oil life

indication● tyre pressure● tyre loading

Unit

Press SET/CLR while page isdisplayed. Select metric (unit 1) orimperial (unit 2) by turning theadjuster wheel. Press SET/CLR to setthe unit of measurement.


Remaining oil life

Indicates an estimate of the oil'suseful life. The number in percentagemeans the current remaining oil lifeand indicates when to change theengine oil and filter 3 64.

Tyre pressure

Tyre pressures of all wheels aredisplayed on this page during driving3 151.

Tyre learn

This display allows for matching newtire and wheel by the tyre pressuremonitoring system sensors 3 151.


Tyre load

The tyre pressure category accordingto the actual tyre inflation pressurecan be selected 3 151.

Outside temperatureDisplay of current outsidetemperature.

LanguageSelect preferred country language asdisplay language.

TimeDisplay of current time.

Info displayThe Info-Display is located in theinstrument panel near the instrumentcluster.Depending on the vehicleconfiguration the vehicle has a● Graphic-Info-Display

or● 7'' Colour-Info-Display with

touch-screen functionalityThe vehicle has a 7'' Colour-Info-Display with touch-screenfunctionality.The Info displays can indicate:● time 3 59● outside temperature 3 59● date 3 59● Infotainment system, see

description in the Infotainmentmanual

● indication of parking assistinstructions 3 122

● system messages● settings for vehicle

personalisation 3 82

Graphic-Info-Display

Press X to switch on the display.Press MENU to select main menupage.Turn MENU to select a menu page.Press MENU to confirm a selection.Press BACK to exit a menu withoutchanging a setting.

7'' Colour-Info-Display

Selecting menus and settingsMenus and settings are accessed viathe display.


Press X to switch on the display.Press ; to display the homepage.Tap required menu display icon withthe finger.Tap a respective icon to confirm aselection.Tap 9 to return to the next highermenu level.Press ; to return to the homepage.For further information, seeInfotainment manual.Vehicle personalisation 3 82.

Valet modeSome functions of the DriverInformation Centre and the Info-Display can be limited for somedrivers.Activation or deactivation of valetmode can be set in the menuSettings in the vehicle personalisationmenu.Vehicle personalisation 3 82.For more information seeInfotainment manual.

Vehicle messagesMessages are indicated mainly in theDriver Information Centre, in somecases together with a warning andsignal buzzer.

Press SET/CLR, MENU or turn theadjuster wheel to confirm a message.


Vehicle messages in DriverInformation Centre

The vehicle messages are displayedas code numbers.

No. Vehicle message

3 Engine coolant level low

4 Air conditioning off

11 Brakes worn

12 Vehicle overloaded

13 Compressor overheated

No. Vehicle message

15 Centre high-mounted brakelight failure

16 Brake light failure

17 Headlight levelling malfunction

18 Left low beam failure

19 Rear fog light failure

20 Right low beam failure

21 Left sidelight failure

22 Right sidelight failure

23 Reversing light failure

24 Number plate light failure

25 Left front turn signal failure

26 Left rear turn signal failure

27 Right front turn signal failure

28 Right rear turn signal failure

35 Replace battery in radio remotecontrol

36 ESC Initialising

No. Vehicle message

49 Lane departure warningunavailable

52 Change timing belt

56 Tyre pressure imbalance onfront axle

57 Tyre pressure imbalance onrear axle

59 Open, then close driver window

60 Open, then close frontpassenger window

61 Open, then close left rearwindow

62 Open, then close right rearwindow

65 Theft attempted

66 Service anti-theft alarm system

67 Service steering wheel lock

68 Service power steering

75 Service air conditioning


No. Vehicle message

77 Service lane departure warning

79 Top up engine oil

81 Service transmission

82 Change engine oil soon

84 Engine power reduced

89 Service vehicle soon

95 Service airbag

145 Check washer fluid level

151 Press clutch to start

174 Low vehicle battery

258 Parking assist off

Vehicle messages onColour-Info-DisplaySome important messages appearadditionally in theColour-Info-Display. Somemessages only pop-up for a fewseconds.

Warning chimesWhen starting the engine or whilstdrivingOnly one warning chime will sound ata time.The warning chime regardingunfastened seat belts has priorityover any other warning chime.● If seat belt is not fastened.● If a door or the tailgate is not fully

closed when starting off.● If a certain speed is exceeded

with parking brake applied.● If a programmed speed is

exceeded.● If a warning message appears in

the Driver Information Centre orInfo-Display.

● If the parking assist detects anobject.

● If unintended lane changeoccurs.

● If a fault in the automatic lockingsystem is detected.

When the vehicle is parked and/orthe driver's door is opened● With exterior lights on.

During an Autostop● If the driver's door is opened.

Battery voltageWhen the vehicle battery voltage isrunning low, the warning code 174 willappear in the Driver InformationCentre.1. Switch off immediately any

electrical consumers which arenot required for a safe drive, e.g.seat heating, heated windscreenand heated rear window or othermain consumers.

2. Charge the vehicle battery bydriving continuously for a while orby using a charging device.

The warning code will disappear afterthe engine has been started twiceconsecutively without a voltage drop.If the vehicle battery cannot berecharged, have the cause of the faultremedied by a workshop.


Vehicle personalisationThe vehicle's behaviour can bepersonalised by changing the settingsin the Info-Display.Some of the personal settings fordifferent drivers can be memorisedindividually for each vehicle key.Memorised settings 3 21.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below maynot be available.Some functions are only displayed oractive when the engine is running.

Personal settingsGraphic-Info-DisplayPress MENU, when ignition is on andinfotainment system is activated.Turn the MENU button to scrollthrough the menu list. Press MENU toselect the respective menu. To closea menu or to go back to previouspage, press BACK.Select Settings, scroll through the listand select Vehicle Settings

In the corresponding submenus thefollowing settings can be changed:

Vehicle Settings● Park Assist / Collision Detection

Park Assist: Activates ordeactivates the ultrasonicparking assist.

● Comfort SettingsChime Volume: Changes thevolume of warning chimes.Personalisation by Driver:Activates or deactivates thepersonalisation function.Rear Auto Wipe in Reverse:Activates or deactivates

automatic switching on of therear window wiper when reversegear is engaged.

● Languages: Scroll through the listand select the desired language.

● LightingExterior lighting by unlocking:Activates or deactivates the entrylighting.Exit Lighting: Activates ordeactivates exit lighting andchanges lighting duration.

● Power Door LocksStop door lock if door open:Activates or deactivates the doorlocking function while a door isopen.Delayed Door Lock: Activates ordeactivates the delayed doorlocking function. This featuredelays the actual locking of thedoors until all doors are closed.

● Remote Lock, Unlock, and StartRemote Unlock Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.


Remote Lock Feedback:Changes what kind of feedbackis given when locking the vehicle.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Auto Relock Doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.

● Restore Factory Settings:Resets all settings to the defaultsettings.

● Valet Mode:Activated, all vehicle displays arelocked and no changes may beperformed within the system.See Infotainment manual.

Personal settings7" Colour-Info-DisplayPress ;, select Settings andthenVehicle on the touch-screen.

In the corresponding submenus thefollowing settings can be changed:

Settings● Climate & Air Quality

Auto Fan Max Speed: Modifiesthe level of the cabin airflow of theclimate control in automaticmode.Air Conditioning Mode: Controlsthe state of the coolingcompressor when the vehicle isstarted. Last setting(recommended) or at vehiclestart is either always on or alwaysoff.

Auto Defog: Supportswindscreen dehumidification byautomatically selecting thenecessary settings andautomatic air conditioning mode.Auto Rear Defog: Automaticallyactivates heated rear window.

● Collision / Detection SystemsPark Assist: Activates ordeactivates the ultrasonicparking assist.

● Comfort and ConvenienceChime Volume: Changes thevolume of warning chimes.Personalization By Driver:Activates or deactivates thepersonalisation function.Auto Wipe in Reverse Gear:Activates or deactivatesautomatic switching on of therear window wiper when reversegear is engaged.

● LightingExit Lighting: Activates ordeactivates and changes theduration of exit lighting.


● Power Door LocksUnlocked Door Anti Lock Out:Activates or deactivates the doorlocking function while a door isopen.Delayed Door Lock: Activates ordeactivates the delayed doorlocking function. This featuredelays the actual locking of thedoors until all doors are closed.

● Remote Lock, Unlock, StartRemote Unlock Light Feedback:Activates or deactivates thehazard warning flasher feedbackwhilst unlocking.Remote Door Unlock: Changesthe configuration to unlock onlythe driver's door or the wholevehicle whilst unlocking.Relock Remotely UnlockedDoors: Activates or deactivatesthe automatic relock functionafter unlocking without openingthe vehicle.

OnStarOnStar is a personal connectivity andservice assistant with integratedWi-Fi hotspot. The OnStar service isavailable 24 hours a day, seven daysa week.NoticeOnStar is not available for allmarkets. For further information,contact your workshop.NoticeIn order to be available andoperational, OnStar needs a validOnStar subscription, functioningvehicle electrics, mobile service andGPS satellite link.

To activate the OnStar services andset up an account, press Z and speakwith an advisor.Depending on the equipment of thevehicle, the following services areavailable:● Emergency services and support

in the case of a vehiclebreakdown

● Wi-Fi hotspot

● Smartphone application● Remote control, e.g. location of

the vehicle, activation of horn andlights, control of central lockingsystem

● Stolen vehicle assistance● Vehicle diagnostics● Destination downloadNoticeThe OnStar module of the vehicle isdeactivated after ten days without anignition cycle. Functions requiring adata connection will be availableagain after switching on the ignition.

OnStar buttons


Privacy buttonPress and hold j until a message isheard to activate or deactivate thetransmission of the vehicle location.Press j to answer a call or to end acall to an advisor.Press j to access the Wi-Fi settings.

Service buttonPress Z to establish a connection toan advisor.

SOS buttonPress [ to establish a priorityemergency connection to a speciallytrained emergency advisor.

Status LEDGreen: The system is ready.Green flashing: The system is on acall.Red: A problem arose.Off: System is in standby mode.Red / green flashing for a short periodof time: Transmission of the vehiclelocation has been deactivated.

OnStar services

General servicesIf you need any informationconcerning e.g. opening hours, pointsof interest and destinations or if youneed any support e.g. in the case of avehicle breakdown, a flat tyre andempty fuel tank, press Z to establisha connection to an advisor.

Emergency servicesIn the case of an emergency situation,press [ and talk to an advisor. Theadvisor then contacts emergency orassistance service providers anddirects them to your vehicle.In the case of an accident withactivation of airbags or belttensioners, an automatic emergencycall is established. The advisor isimmediately connected to yourvehicle to see whether help isneeded.

Wi-Fi hotspotThe Wi-Fi hotspot of the vehicleprovides internet connectivity with amaximum speed of 4G/LTE.

NoticeThe Wi-Fi hotspot functionality is notavailable for all markets.

Up to seven devices may beconnected.To connect a mobile device with theWi-Fi hotspot:1. Press j and then select Wi-Fi

settings on the Info-Display. Thesettings displayed include the Wi-Fi hotspot name (SSID),password and connection type.

2. Start a Wi-Fi network search onyour mobile device.

3. Select your vehicle hotspot(SSID) when listed.

4. When prompted, enter thepassword on your mobile device.

NoticeTo change the SSID or password,press Z and talk to an advisor or login to your account.

To switch off the Wi-Fi hotspotfunctionality, press Z to call anadvisor.


Smartphone appWith the My Vauxhall smartphoneapp, some vehicle functions can beoperated remotely.The following functions are available:● Lock or unlock vehicle.● Honk horn or flash lights.● Check fuel level, engine oil life

and tyre pressure (only with tyrepressure monitoring system).

● Send navigation destination tothe vehicle, if equipped with abuilt-in navigation system.

● Locate vehicle on a map.● Manage Wi-Fi settings.

To operate these functions, downloadthe app from Apple's App Store orGoogle Play Store.

Remote controlIf desired, use any phone to call anadvisor, who can remotely operatespecific vehicle functions. Find therespective OnStar phone number onour country-specific website.

The following functions are available:● Lock or unlock vehicle.● Provide information on the

vehicle location.● Honk horn or flash lights.

Stolen vehicle assistanceIf the vehicle is stolen, report the theftto the authorities and request OnStarstolen vehicle assistance. Use anyphone to call an advisor. Find therespective OnStar phone number onour country-specific website.OnStar can provide support inlocating and recovering the vehicle.Theft alertWhen the anti-theft alarm system istriggered, a notification is sent toOnStar. You are then informed aboutthis event by text message or email.Restart preventionBy sending remote signals, OnStarcan prevent the vehicle fromrestarting once it has been turned off.

On-demand diagnosticsAt any time e.g. if the vehicle displaysa vehicle message, press Z tocontact an advisor and ask tocomplete a real-time diagnostic checkto directly determine the issue.Depending on the results, the advisorwill provide further support.

Diagnostic reportThe vehicle automatically transmitsdiagnostic data to OnStar whichsends a monthly email report to youand your preferred workshop.NoticeThe workshop notification functioncan be disabled in your account.

The report contains the status of keyoperating systems of the vehicle likeengine, transmission, airbags, ABS,and other major systems. It alsoprovides information on possiblemaintenance items and tyre pressure(only with tyre pressure monitoringsystem).To look at the information in greaterdetail, select the link within the emailand log in to your account.


Destination downloadA desired destination can be directlydownloaded to the navigation system.Press Z to call an advisor anddescribe the destination or point ofinterest.The advisor can look up any addressor point of interest and directly sendthe destination to the built-innavigation system.

OnStar settings

OnStar PINTo have full access to all OnStarservices, a four-digit PIN is required.The PIN has to be personalised whenfirst talking to an advisor.To change the PIN, press Z to call anadvisor.

Account dataAn OnStar subscriber has an accountwhere all the data is stored. Torequest a change of the accountinformation, press Z and talk to anadvisor or log in to your account.

If the OnStar service is used onanother vehicle, press Z and requestthat the account be transferred to thenew vehicle.NoticeIn any case, if the vehicle is disposedof, sold or otherwise transferred,immediately inform OnStar aboutthe changes and terminate theOnStar service on this vehicle.

Vehicle locationThe vehicle location is transmitted toOnStar when service is requested ortriggered. A message on the Info-Display informs about thistransmission.To activate or deactivate thetransmission of the vehicle location,press and hold j until an audiomessage is heard.The deactivation is indicated by thestatus light flashing red and green fora short period of time and each timethe vehicle is started.NoticeIf the transmission of the vehiclelocation is deactivated, someservices are no longer available.

NoticeThe vehicle location always remainsaccessible to OnStar in the case ofan emergency.

Find the privacy policy in youraccount.

Software updatesOnStar may remotely carry outsoftware updates without furthernotice or consent. These updates areto enhance or maintain safety andsecurity or the operation of thevehicle.These updates may concern privacyissues. Find the privacy policy in youraccount.

88 Lighting

Lighting

Exterior lighting ............................ 88Light switch ................................ 88High beam ................................. 88Headlight flash ........................... 88Headlight range adjustment ...... 89Headlights when drivingabroad ...................................... 89

Daytime running lights ............... 89Cornering lights ......................... 89Hazard warning flashers ............ 89Turn and lane-change signals ... 90Front fog lights ........................... 90Rear fog light ............................. 90Parking lights ............................. 91Reversing lights ......................... 91Misted light covers ..................... 91

Interior lighting ............................. 91Instrument panel illuminationcontrol ....................................... 91

Interior lights .............................. 92Reading lights ............................ 92

Lighting features .......................... 93Exit lighting ................................ 93Battery discharge protection ...... 93

Exterior lightingLight switch

Turn light switch:7 : lights off8 : sidelights9 : headlights

Control indicator 8 3 72.

Tail lightsTail lights are illuminated togetherwith headlights and sidelights.

High beam

To switch from low to high beam,push lever.To switch to low beam, push leveragain or pull.

Headlight flashTo activate the headlight flash, pulllever.

Lighting 89

Headlight range adjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 : front seats occupied1 : all seats occupied2 : all seats occupied and load

compartment laden3 : driver's seat occupied and load

compartment laden

Headlights when drivingabroadHeadlight aim has been preset andshould need no further adjustment.When driving in countries withopposite hand traffic, it is notnecessary to adjust the headlights.

Daytime running lightsDaytime running light increasesvisibility of the vehicle during daylight.They are switched on automaticallywhen ignition is on.

Cornering lights

On tight bends or when turning off,depending on the steering angle orthe indicator light signal, an additionalleft or right reflector is switched on

which illuminates the road in thedirection of travel. It is activated up toa speed of 25 mph.

Hazard warning flashers

Operated by pressing ¨.In the event of an accident with airbagdeployment, the hazard warningflashers are activated automatically.

90 Lighting

Turn and lane-changesignals

lever up : right turn signallever down : left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.For three flashes, e.g., whenchanging lanes, press the lever untilresistance is felt and then release.Move the lever to the resistance pointand hold for longer indication.

Switch the turn signal off manually bymoving the lever to its originalposition.

Front fog lights

Operated by pressing >.

Rear fog light

Operated by pressing r.Light switch in position 8: Rear foglight can only be switched on withfront fog lights.

Lighting 91

Parking lights

When the vehicle is parked, theparking lights on one side can beactivated:1. Switch off the ignition.2. Move the turn signal lever all the

way up (right parking lights) ordown (left parking lights).

Confirmed by an acoustic signal andthe corresponding turn signal controlindicator.

Reversing lightsThe reversing light comes on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted when the exterior lightsare on:● instrument panel illumination● Info-Display● illuminated switches and

operation elementsTurn thumb wheel A and hold untilthe desired brightness is obtained.

92 Lighting

Interior lightsWhen opening a door, the courtesylight automatically switches on andthen off after a delay.When exterior lighting has been on,courtesy light will turn on whenignition is switched off.NoticeIn the event of an accident withairbag deployment, the courtesylights are turned on automatically.

Courtesy light

Operate rocker switch:centreposition w

: automatic switching onwhen opening a door.Turns off after a delay.

press d : permanently onpress K : permanently off

Reading lights

Operated by pressing the buttons infront.

Dome lightSpotlight incorporated in the interiorlighting comes on when headlightsare switched on.Dome light illuminates gear shiftingconsole indirectly.

Lighting 93

Lighting featuresExit lightingPath lightingHeadlights, tail lights and numberplate lights illuminate the surroundingarea for an adjustable time afterleaving the vehicle.

Activating

1. Switch off the ignition.2. Remove the ignition key.3. Open driver's door.

4. Pull the turn signal lever.5. Close the driver's door.

If the driver's door is not closed thelights switch off after two minutes.Exit lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.Activation, deactivation and durationof this function can be changed in theInfo-Display. Vehicle personalisation3 82.The settings can be saved for the keybeing used 3 21.

Battery discharge protectionSwitching off electric lightsTo prevent discharge of the vehiclebattery when the ignition is switchedoff, some interior lights are switchedoff automatically after some time.

94 Climate control

Climate control

Climate control systems ............... 94Heating and ventilation system . 94Air conditioning system ............. 95Electronic climate controlsystem ...................................... 97

Air vents ..................................... 100Adjustable air vents ................. 100Fixed air vents ......................... 101

Maintenance .............................. 101Air intake ................................. 101Pollen filter ............................... 101Air conditioning regularoperation ................................ 101

Service .................................... 102

Climate control systemsHeating and ventilationsystem

Controls for:● temperature● fan speed● air distribution● demisting and defrosting● air recirculation

Heated rear window Ü 3 29.Heated seats ß 3 34.Heated steering wheel * 3 57.

TemperatureAdjust the temperature by turning thetemperature control.red : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Air distributionM : to head area via adjustable air

ventsL : to head area and foot wellK : to foot well, with a small amount

of air being directed towindscreen and front doorwindows

J : to windscreen and foot well,with a small amount of air beingdirected to front door windows

V : to windscreen and front doorwindows

Intermediate settings are possible.

Climate control 95

Demisting and defrosting thewindows● Set air distribution control to V.● Set temperature control to

warmest level.● Set fan speed to highest speed.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards doorwindows.

● For simultaneous warming of thefoot well, set air distributioncontrol to J.

Air conditioning system

Controls for:● temperature● fan speed● air distribution

A/C : cooling4 : air recirculationÜ : heated rear window

Heated rear window 3 29.Heated seats ß 3 34.Heated steering wheel * 3 57.

TemperatureAdjust the temperature by turning thetemperature control.red : warmblue : cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Air distributionM : to head area via adjustable air

ventsL : to head area and foot wellK : to foot well, with a small amount



V : to windscreen and front doorwindows (air conditioning isactivated in the background tohelp preventing windows fromfogging)

Intermediate settings are possible.

Cooling A/CPress A/C to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.Press A/C again to switch off cooling.

96 Climate control

The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.Activated cooling may inhibitAutostops.Stop-start system 3 106.

Air recirculation system 4Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivate airrecirculation mode.

9 Warning

Driving with recirculation mode fora prolonged period of time canmake you sleepy. Periodically turnto the outside air mode for freshair.

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up. The qualityof the passenger compartment airdeteriorates, which may cause thevehicle occupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside, when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper and deactivate V.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.● Switch on cooling A/C.● Switch on Air recirculation

system 4.● Set temperature control to

coldest level.● Set fan speed to highest level.● Set air distribution control to M.● Open all vents.

Demisting and defrosting thewindows V● Set air distribution control to V.● Set temperature control to

warmest level.● Set fan speed to highest level.● Switch on heated rear window Ü.● Open side air vents as required

and direct them towards the doorwindows.

When V is switched on, A/Coperates and air recirculation modewill be fixed to outside air moderegardless of indicator status.NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If V is pressed while the engine isin an Autostop, the engine will restartautomatically.

Stop-start system 3 106.

Climate control 97

Electronic climate controlsystem

Controls for:● temperature● air distribution● fan speed

A/C : coolingAUTO : automatic mode4 : manual air recirculationV : demisting and defrostingÜ : heated rear window

Heated rear window 3 29.Heated seats ß 3 34.Heated steering wheel * 3 57.

Climate control settings are shown onthe Info-Display. Settingmodifications are briefly popped-up,superimposed over the currentlydisplayed menu.The electronic climate control systemis only fully operational when theengine is running.Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Automatic mode AUTOThe system automatically controls thefan speed, air delivery, airconditioning, and recirculation inorder to heat or cool the vehicle to thedesired temperature.When the AUTO indicator light is on,the system is in full automaticoperation.If the air delivery mode, fan speed,recirculation, or air conditioningsetting is adjusted, the AUTOindicator turns off.To improve fuel efficiency and to coolthe vehicle faster, recirculation maybe automatically selected in warm

weather. The recirculation light willnot come on. Press 4 to selectrecirculation; press it again to selectoutside air.To turn off the system, press power m.Basic setting for maximum comfort:● Press AUTO. The LED in the

button illuminates to indicateactivation.

● Open all air vents to allowoptimised air distribution inAutomatic mode.

● Set the preselected temperature.Recommended temperature is22 °C.

Temperature preselectionSet temperature to the desired value.It is indicated on the display in thetemperature control.For reasons of comfort, changetemperature only in small increments.If the minimum temperature Lo is set,the climate control system runs atmaximum cooling, if cooling A/C isactive.

98 Climate control

If the maximum temperature Hi is set,the climate control system runs atmaximum heating.Recommended temperature is 22 °C.NoticeIf A/C is switched on, reducing theset cabin temperature can cause theengine to restart from an Autostop orinhibit an Autostop.


Demisting and defrosting thewindows V● Press V. The LED in the button

illuminates to indicate activation.● Temperature and air distribution

are set automatically and the fanruns at high speed.

● Switch on heated rear window Ü.● To return to previous mode:

press V. To return to Automaticmode: press AUTO.

NoticeIf V is pressed while the engine isrunning, an Autostop will be inhibiteduntil V is pressed again.If V is pressed while the engine isin an Autostop, the engine will restartautomatically.


Air recirculation system 4Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivate airrecirculation mode.

9 Warning

Driving with recirculation mode fora prolonged period of time canmake you sleepy. Periodically turnto the outside air mode for freshair.The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so the

windows may mist up. The qualityof the passenger compartment airdeteriorates, which may cause thevehicle occupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside, when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper and deactivate V.

Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as follows.Changing a setting will deactivateAutomatic mode.

Climate control 99

Fan speed Z

Adjust the air flow by switching the fanto the desired speed. The selectedfan speed is indicated by the numberof segments in the display. If the fanis switched off the air conditioning isalso deactivated.To return to Automatic mode: PressAUTO.

Air distribution

Press appropriate button for desiredadjustment. Activation is indicated bythe LED in the button.M : to head areaL : to head area and foot wellK : to foot well, with a small amount



V : to windscreen and front doorwindows (air conditioning isactivated in the background tohelp preventing windows fromfogging)

To return to Automatic mode: PressAUTO.

Cooling A/C

Press A/C to switch on cooling. TheLED in the button illuminates toindicate activation. Cooling is onlyfunctional when the engine is runningand climate control fan is switched on.

100 Climate control

Press A/C again to switch off cooling.The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch off the cooling system for fuelsaving reasons.Activated cooling might inhibitAutostops.Stop-start system 3 106.

Air recirculation mode 4Press 4 to activate air recirculationmode. The LED in the buttonilluminates to indicate activation.Press 4 again to deactivate airrecirculation mode.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling, theair humidity increases, so the

windows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen may mistup from outside when cold air isdirected towards it. If windscreenmists up from outside, activatewindscreen wiper.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.● Switch on cooling A/C.● Switch on Air recirculation

system 4.● Set temperature control to

coldest level.● Set fan speed to highest level.● Set air distribution control to M.● Open all vents.

Air ventsAdjustable air ventsAt least one air vent must be openwhile the cooling is on.

Direct the flow of air by tilting andswivelling the slats.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Climate control 101

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

The filter should be replaced as partof routine scheduled maintenance.

Caution

More frequent maintenance of thepassenger compartment air filter isrequired if the drivingcircumstances are dusty roads, airpollution areas, and frequentunpaved roads.The filter efficiency is decreasedand the bronchus is badlyaffected.

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes once amonth, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

102 Climate control

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:● functionality and pressure test● heating functionality● leakage check● check of drive belts● cleaning of condenser and

evaporator drainage● performance check

Driving and operating 103

Driving andoperating

Driving hints ............................... 103Control of the vehicle ............... 103Steering ................................... 104

Starting and operating ............... 104New vehicle running-in ............ 104Ignition switch positions ........... 104Retained power off .................. 105Starting the engine .................. 105Overrun cut-off ........................ 106Stop-start system .................... 106Parking .................................... 109

Engine exhaust .......................... 110Catalytic converter ................... 110

Manual transmission .................. 110Manual transmission automa‐ted .............................................. 111

Transmission display ............... 111Starting the engine .................. 111Selector lever .......................... 112Manual mode ........................... 113Electronic driving programmes 113Fault ........................................ 113

Brakes ........................................ 114Antilock brake system ............. 114Parking brake .......................... 115Brake assist ............................. 115Hill start assist ......................... 115

Ride control systems ................. 116Traction Control system .......... 116Electronic Stability Control ...... 117City mode ................................ 118

Driver assistance systems ......... 119Cruise control .......................... 119Speed limiter ........................... 121Parking assist .......................... 122Lane departure warning .......... 123

Fuel ............................................ 124Fuel for petrol engines ............. 124Fuel for liquid gas operation .... 125Refuelling ................................ 127Fuel consumption - CO2-Emissions ............................... 130

Driving hintsControl of the vehicleNever coast with engine notrunningMany systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner is adanger to yourself and others.All systems function during anAutostop.Stop-start system 3 106.

Idle boostIf charging of the vehicle battery isrequired due to battery condition, thepower output of the generator mustbe increased. This will be achieved byan idle boost which may be audible.A message appears in the DriverInformation Centre.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

104 Driving and operating

Use only floor mats, which fit properlyand are fixed by the retainers on thedriver side.

Driving downhillEngage a gear when driving downhillto ensure that sufficient brakepressure is available.

SteeringIf power steering assist is lostbecause the engine stops or due to asystem malfunction, the vehicle canbe steered but may require increasedeffort.Control indicator c 3 70.

Caution

Vehicle equipped with electricpower steering:If the steering wheel is turned untilit reaches the end of its travel andis held against that position for anextended period of time, powersteering assistance may bereduced.

If the steering assistance is usedfor an extended period of time,power assistance may bereduced.Power steering assistance shouldreturn back to normal when thesystem has cooled down.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open for awhile after the first drive and avoidinhaling the fumes.During the running-in period, fuel andengine oil consumption may behigher.Autostop may be inhibited to allow forcharging of the vehicle battery.

Ignition switch positionsTurn key:


0 : ignition off: Some functionsremain active until key isremoved or driver's door isopened, provided the ignition wason previously

1 : accessory power mode: Steeringwheel lock released, someelectrical functions are operable,ignition is off

2 : ignition on power mode: Ignitionis on. Control indicatorsilluminate and most electricalfunctions are operable

3 : engine start: Release key afterstarting procedure begins

Steering wheel lockRemove key from ignition switch andturn steering wheel until it engages.

Retained power offThe following electronic systems areoperable until the driver's door isopened or at the latest for ten minutesafter the ignition is switched off:● power windows● power outlets● power sunroof

Power to the Infotainment system willcontinue to operate for 30 minutes oruntil the key is removed from theignition switch, regardless of whetherany door is opened.

Starting the engine

Turn key to position 1 to release thesteering wheel lock.Manual transmission: operate clutchand brake pedal.Manual transmission automated:operate brake pedal.Do not operate the accelerator pedal.Turn key briefly to position 3 andrelease: an automatic procedureoperates the starter after a briefdelay, until the engine is running. See"Automatic Starter Control".


Before restarting or to switch off theengine, turn the key back to position0.During an Autostop, the engine canbe started by depressing the clutchpedal.

Starting the vehicle at lowtemperaturesThe start of the engine withoutadditional heaters is possible down to-30 °C.Required is an engine oil with thecorrect viscosity, the correct fuel,performed services and a sufficientlycharged vehicle battery.

Automatic starter controlThis function controls the enginestarting procedure. The driver doesnot need to hold the key in position 3.Once applied, the system will go onstarting automatically until the engineis running. Because of the checkingprocedure, the engine starts runningafter a short delay.

Possible reasons for a non-startingengine:● clutch pedal not operated

(manual transmission)● brake pedal not operated

(manual transmissionautomated)

● timeout occurred

Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Overrun cut-offThe fuel supply is automatically cut-off during overrun, i.e. when thevehicle is driven with a gear engagedbut accelerator is released.

Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, it

switches off the engine as soon as thevehicle is at a low speed or at astandstill, e.g. at a traffic light or in atraffic jam.On vehicles with manualtransmission, the engine is startedautomatically as soon as the clutch isdepressed.On vehicles with manual transmissionautomated, the engine is startedautomatically as soon as the brakepedal is released.A vehicle battery sensor ensures thatan Autostop is only performed if thevehicle battery is sufficiently chargedfor a restart.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.


Deactivation

Deactivate the stop-start systemmanually by pressing Ï. Thedeactivation is indicated when theLED in the button extinguishes.

AutostopVehicles with manual transmissionIf the vehicle is at a low speed or at astandstill, activate an Autostop asfollows:● Depress the clutch pedal.● Set the lever in neutral.● Release the clutch pedal.

The engine will be switched off whilethe ignition stays on.Vehicles with manual transmissionautomatedIf the vehicle is at a standstill with thebrake pedal depressed, Autostop isactivated automatically.The engine will be switched off whilethe ignition stays on.The stop-start system will be disabledon inclines of 15% or more.

Indication

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.

During an Autostop, the heating andbrake performance will bemaintained.

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled:● The stop-start system is not

manually deactivated.● The bonnet is fully closed.● The driver's door is closed or the

driver's seat belt is fastened.● The vehicle battery is sufficiently

charged and in good condition.● The engine is warmed-up.● The engine coolant temperature

is not too high.● The engine exhaust temperature

is not too high, e.g. after drivingwith high engine load.

● The ambient temperature isabove -5 °C.

● The climate control systemallows an Autostop.


● The brake vacuum is sufficient.● The vehicle was driven at least at

walking speed since the lastAutostop.

Otherwise an Autostop will beinhibited.Certain settings of the climate controlsystem may inhibit an Autostop. See"Climate control" chapter for furtherinformation 3 97.Immediately after motorway drivingan Autostop may be inhibited.New vehicle running-in 3 104.

Vehicle battery discharge protectionTo ensure reliable engine restarts,several vehicle battery dischargeprotection features are implementedas part of the stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures, e.g., the rear windowheating, are disabled or switched intoa power saving mode. The fan speedof the climate control system isreduced to save power.

Restart of the engine by the driverVehicles with manual transmissionDepress the clutch pedal to restart theengine.If the selector lever is shifted out ofneutral before depressing the clutchpedal first, control indicator -illuminates or is shown as a symbol inthe Driver Information Centre.Control indicator - 3 69.Vehicles with manual transmissionautomatedRelease the brake pedal or moveselector lever out of D to restart theengine.

Restart of the engine by the stop-start systemThe selector lever must be in neutralto enable an automatic restart.If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system:● The stop-start system is

manually deactivated.● The bonnet is opened.

● The driver's seat belt isunfastened and the driver's dooris opened.

● The engine temperature is toolow.

● The charging level of the vehiclebattery is below a defined level.

● The brake vacuum is notsufficient.

● The vehicle is driven at least atwalking speed.

● The climate control systemrequests an engine start.

● The air conditioning is manuallyswitched on.

If the bonnet is not fully closed, awarning message is displayed in theDriver Information Centre.If an electrical accessory, e.g. aportable CD player, is connected tothe power outlet, a brief power dropduring restart might be noticeable.


Parking

9 Warning

● Do not park the vehicle on aneasily ignitable surface. Thehigh temperature of theexhaust system could ignite thesurface.

● Always apply the parkingbrake. Activate the manualparking brake without pressingthe release button. Apply asfirmly as possible on a downhillslope or uphill slope. Depressbrake pedal at the same time toreduce operating force.

● Switch off the engine.● If the vehicle is on a level

surface or uphill slope, engagefirst gear before removing theignition key. On an uphill slope,turn the front wheels away fromthe kerb.If the vehicle is on a downhillslope, engage reverse gearbefore removing the ignition

key. Turn the front wheelstowards the kerb.

● Close the windows and thesunroof.

● Remove the ignition key fromthe ignition switch. Turn thesteering wheel until thesteering wheel lock is felt toengage.

For vehicles with manualtransmission automated, the keycan only be removed from theignition switch when the parkingbrake is applied.

● Lock the vehicle.● Activate the anti-theft alarm

system.● The engine cooling fans may run

after the engine has beenswitched off 3 133.

Caution

After running at high enginespeeds or with high engine loads,operate the engine briefly at a low

load or run in neutral forapprox. 30 seconds beforeswitching off, in order to protectthe turbocharger.

NoticeIn the event of an accident withairbag deployment, the engine isswitched off automatically if thevehicle comes to a standstill within acertain time.


Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Caution

Fuel grades other than those listedon pages 3 124, 3 177 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the faultrectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Manual transmission

To engage reverse, depress theclutch pedal and engage the reversegear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not slip the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.


Caution

It is not advisable to drive with thehand resting on the selector lever.

Upshift indication 3 70.Stop-start system 3 106.

Manual transmissionautomatedThe automated manual transmissionpermits manual gearshifting (manualmode) or automatic gearshifting(automatic mode), both withautomatic clutch control.Manual shifting is possible by tappingthe selector lever in manual mode.NoticeWhen unlocking or opening avehicle door, a sound may beaudible caused by the hydraulicsystem.

Transmission display

In automatic mode, the drivingprogramme is indicated by D in theDriver Information Centre.In manual mode, M and the numberof the selected gear is indicated.R indicates reverse gear.N indicates neutral.

Starting the engineTo start the engine, depress the brakepedal, if transmission is not in positionN.


Transmission automatically shifts toN upon starting. There may be a slightdelay.Starting is not possible if all brakelights fail.

Selector lever

Always move the selector lever in theappropriate direction as far as it willgo. Upon release, it automaticallyreturns to the centre position.

N : neutral positionD/M : switch between automatic (D)

and manual (M) shift mode.The transmission displayshows either D or M with theselected gear

< : upshifting in manual mode] : downshifting in manual modeR : reverse gear. Engage only

when vehicle is stationary

If selector lever is moved from R to theleft, D is directly engaged.If selector lever is moved from D to< or ], manual mode M is selectedand the transmission shifts.

Starting offDepress the brake pedal and movethe selector lever to D/M or R. If D isselected, transmission is in automaticmode and first gear is engaged. If Ris selected, reverse gear is engaged.The vehicle starts to move when thebrake pedal is released.To start off immediately withoutdepressing the brake pedal, move theselector lever to D or R. D or R willflash for a short time in the Driver

Information Centre. Accelerate aslong as D or R flashes. The selectedgear is engaged and the vehicle startsmoving.If the accelerator pedal is notdepressed as long as D or R areflashing in the Driver InformationCentre, no gear is engaged.

Stopping the vehicleIn D, first gear is engaged and theclutch is released when the vehicle isstopped. In R, reverse gear remainsengaged.

Engine braking

Automatic modeWhen driving downhill, the manualtransmission automated does notshift into higher gears until a fairlyhigh engine speed has been reached.It shifts down in good time whenbraking.


Manual modeTo utilise the engine braking effect,select a lower gear in good time whendriving downhill. Changing intomanual mode is only possible whilethe engine is running.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between R and D in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingThe most recently engaged gear (seetransmission display) remainsengaged when switching off ignition.With N, no gear is engaged.Therefore always apply the parkingbrake when switching off ignition. Ifparking brake is not applied, P flashesin the transmission display and thekey cannot be removed from theignition switch. P stops flashing in thetransmission display as soon as theparking brake is slightly applied.

When the ignition is switched off, thetransmission no longer responds tomovement of the selector lever.

Tyre pressure monitoring systemTo start the sensor matching processof the tyre pressure monitoringsystem, the selector lever must bemoved and held in position N forfive seconds. P illuminates in thetransmission display to indicate thatthe sensor matching process can bestarted.Tyre pressure monitoring system3 151.

Manual modeIf a higher gear is selected when theengine speed is too low, or a lowergear when the speed is too high, theshift is not executed. This preventsthe engine from running at too low ortoo high an engine speed. M and thenumber of the selected gear will beflashed, then the current gear isdisplayed again..

If engine speed is too low, thetransmission automatically shifts to alower gear.When + or - is selected in automaticmode, the transmission switches tomanual mode and shifts accordingly.

Gear shift indicationThe symbol R with a numberalongside it, is indicated whengearshifting is recommended for fuelsaving reasons.Shift indication appears only inmanual mode.

Electronic drivingprogrammesThe adaptive programme tailorsgearshifting to the driving conditions,e.g. greater load or gradients.

FaultTo prevent damage to the manualtransmission automated, the clutch isengaged automatically at high clutchtemperatures.


In the event of a fault, control indicatorg illuminates. Additionally, awarning message is displayed in theDriver Information Centre. Vehiclemessages 3 79.Continued driving is restricted or notpossible, depending on the fault.Have the cause of the fault remediedby a workshop.

BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing the journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 69.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting-off the system performsa self-test which may be audible.Control indicator u 3 70.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.


Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

Parking brakeManual parking brake

9 Warning

Always apply parking brake firmlywithout operating the releasebutton, and apply as firmly aspossible on a downhill or uphillslope.To release the parking brake, pullthe lever up slightly, press therelease button and fully lower thelever.

To reduce the operating forces ofthe parking brake, depress thebrake pedal at the same time.

Control indicator R 3 69.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the brake pedal afterstopping on an incline, the brakesremain on for a further two seconds.The brakes release automatically as


soon as the vehicle begins toaccelerate or the two seconds holdingtime is over.The hill start assist is not active duringan Autostop.

Ride control systemsTraction Control systemThe Traction Control system (TC) is acomponent of the Electronic StabilityControl (ESC).TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels start tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.

TC is operational after each enginestart as soon as the control indicatorb extinguishes.When TC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Deactivation

TC can be switched off when spinningof drive wheels is required: press tbriefly.


Control indicator k illuminates.When TC is deactivated, ESCremains active.TC is reactivated by pressing t again.TC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system thecontrol indicator b illuminatescontinuously and a warning codeappears in the Driver InformationCentre. The system is notoperational.Have the cause of the fault remediedby a workshop.

Electronic Stability ControlElectronic Stability Control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually.ESC operates in combination with theTraction Control system (TC). Itprevents the drive wheels fromspinning.

ESC is operational after each enginestart as soon as the control indicatorb extinguishes.When ESC operates b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 70.

Deactivation

For very high-performance drivingESC can be deactivated:Press and hold t for a minimum offive seconds. Control indicator tilluminates.


ESC is reactivated by pressing tagain. If the TC system waspreviously disabled, both TC andESC are reactivated. k and textinguish when TC and ESC arereactivated.ESC is also reactivated the next timethe ignition is switched on.

FaultIf there is a fault in the system, thecontrol indicator b illuminatescontinuously and a warning codeappears in the Driver InformationCentre. The system is notoperational.Have the cause of the fault remediedby a workshop.

City modeCity mode is a feature which enablesincreased steering assistance duringlower speed conditions, e.g. citytraffic or parking. Steering assistanceis increased for greater convenience.

Activation

Press B when engine is running. Thesystem works from standstill up to37 mph, and also in reverse gear.Above this speed, the systemchanges to normal mode. Whenactivated, City mode engagesautomatically below 37 mph.An illuminated LED in the City modebutton indicates that the system isactive and a message pops-up in theDriver Information Centre.City mode remains active during anAutostop, but is only operationalwhen the engine is running.Stop-start system 3 106.

DeactivationPress B. The LED in the buttonextinguishes.Each time the engine is started, Citymode is deactivated.

OverloadIf the steering in City mode is heavilyloaded, e.g. in long parkingmanoeuvres or heavy city traffic, thesystem is deactivated for overheatprotection. Steering operates innormal mode until City modeactivates automatically

Fault


In the event of a fault in the system,control indicator c illuminates.Vehicle messages 3 79.

Driver assistancesystems

9 Warning

Driver assistance systems aredeveloped to support the driverand not to replace the driver'sattention.The driver accepts fullresponsibility when driving thevehicle.When using driver assistancesystems, always take careregarding the current trafficsituation.

Cruise controlThe cruise control can store andmaintain speeds of approx. 15 mph to105 mph. Deviations from the storedspeeds may occur when driving uphillor downhill.For safety reasons, the cruise controlcannot be activated until the brakepedal has been operated once.Activating in first gear is not possible.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.On vehicles with manual transmissionautomated, cruise control can beactivated in automatic mode andmanual mode.Control indicator m 3 72.

Switching on


Press m; control indicator m ininstrument cluster illuminates white.

ActivationAccelerate to the desired speed andturn thumb wheel to SET/-, thecurrent speed is stored andmaintained. Control indicator m ininstrument cluster illuminates green.Set speed is indicated on the display.Accelerator pedal can be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.Cruise control remains activatedwhile gearshifting.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.Alternatively accelerate to the desiredspeed and store by turning to SET/-.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turn toSET/- repeatedly: speed decreasescontinuously or in small increments.

DeactivationPress y; control indicator m ininstrument cluster illuminates white.Cruise control is deactivated. Laststored speed remains in memory forlater speed resume.

Automatic deactivation:● Vehicle speed is below approx.

15 mph.● The brake pedal is depressed.● The clutch pedal is depressed for

a few seconds.● The selector lever is in N.● Engine speed is in a very low

range.● The Traction Control system or

Electronic Stability Control isoperating.

Resume stored speedTurn thumb wheel to RES/+ at aspeed above 15 mph. The storedspeed will be obtained.

Switching offPress m, control indicator m ininstrument cluster extinguishes. Thestored speed is deleted.Pressing L to activate the speedlimiter or switching off the ignition alsoswitches off cruise control anddeletes the stored speed.


Speed limiterThe speed limiter prevents exceedinga preset maximum speed.The maximum speed can be set atspeeds above 18 mph.The driver can only accelerate up tothe preset speed. Deviations from thelimited speed may occur when drivingdownhill.The preset speed limit is displayed inthe Driver Information Centre whenthe system is active.

Activation

Press L. If cruise control has beenactivated before, it is switched offwhen speed limiter is activated andcontrol indicator m extinguishes.

Set speed limitWith speed limiter active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly until the desiredmaximum speed is displayed in theDriver Information Centre.Alternatively, accelerate to thedesired speed and briefly turn thumbwheel to SET/-: the current speed isstored as maximum speed. Speedlimit is displayed in the DriverInformation Centre.

Change speed limitWith speed limiter active, turn thumbwheel to RES/+ to increase or SET/-to decrease the desired maximumspeed.

Exceeding the speed limitWhen exceeding the limited speedwithout driver input, the speed willflash in the Driver Information Centreand a chime sounds during thisperiod.In the event of an emergency, it ispossible to exceed the speed limit bydepressing the accelerator pedalfirmly nearly to the final point.Release the accelerator pedal andthe speed limiter function isreactivated once a speed lower thanthe limit speed is obtained.

DeactivationPress y: speed limiter is deactivatedand the vehicle can be driven withoutspeed limit.


The limited speed will be stored andis indicated in brackets in the DriverInformation Centre. Additionally, acorresponding message appears.

Resume speed limitTurn thumb wheel to RES/+. Thestored speed limit will be obtained.

Switching offPress L, the speed limit indicationextinguishes in the Driver InformationCentre. The stored speed is deleted.By pressing m to activate cruisecontrol, speed limiter is alsodeactivated and the stored speed isdeleted.By switching off the ignition, speedlimiter is also deactivated, but thespeed limit will be stored for nextspeed limiter activation.

Parking assistRear parking assist

9 Warning

It is the driver who bears fullresponsibility for the parkingmanoeuvre.Always check the surroundingarea while reversing and using therear parking assist system.

The rear parking assist makesparking easier by measuring thedistance between the vehicle and

rear obstacles. It informs and warnsthe driver by giving acoustic signalsand display indication.The system has three ultrasonicparking sensors in the rear bumper.

ActivationWhen reverse gear is engaged, thesystem is ready to operateautomatically.

IndicationThe system warns the driver withacoustic signals against potentiallyhazardous obstacles behind thevehicle. The interval between thesounds becomes shorter as thevehicle gets closer to that obstacle.When the distance is less thanapprox. 40 cm, the sound iscontinuous.

DeactivationThe system automatically switchesoff when reverse gear is disengaged.The system might not detect theobstacle when the vehicle is drivenabove a 10 km/h.


FaultIn the event of a fault in the system,control indicator r illuminates in theinstrument cluster 3 70.Additionally if the system does notwork due to temporary conditions likesnow covered sensors, rilluminates.

Basic notes on parking assistsystems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.Special attention must be paid tolow obstacles which can damagethe lower part of the bumper.

Caution

Performance of the system can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystem can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles in the vicinity(e.g. off-road vehicles, mini vans,vans). Object identification andcorrect distance indication in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross-section, e.g. objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist systems do notdetect objects outside thedetection range.

Lane departure warningThe lane departure warning systemobserves the lane markings betweenwhich the vehicle is driving via a frontcamera. The system detects lane

changes and warns the driver in theevent of an unintended lane changevia visual and acoustic signals.Criteria for the detection of anunintended lane change are:● No operation of turn signals.● No brake pedal operation.● No active accelerator operation

or speeding-up.● No active steering.

If the driver is performing theseactions, no warning will be issued.

Activation


The lane departure warning system isactivated by pressing ). Theilluminated LED in the buttonindicates that the system is switchedon. When control indicator ) in theinstrument cluster illuminates green,the system is ready to operate.The system is only operable atvehicle speeds above 35 mph and iflane markings are available.When the system recognises anunintended lane change, controlindicator ) changes to yellow andflashes. Simultaneously a chimesound is activated.

DeactivationThe system is deactivated bypressing ), the LED in the buttonextinguishes.At speeds below 35 mph the systemis inoperable.

FaultThe lane departure warning systemmay not operate properly when:● The windscreen is not clean.● There are adverse environmental

conditions e.g. heavy rain, snow,direct sunlight or shadows.

The system can not operate when nolane marking is detected.

FuelFuel for petrol enginesOnly use unleaded fuel that complieswith European standard EN 228 orE DIN 51626-1 or equivalent.The engine is capable of running withfuel that contains up to 10% ethanol(e.g., named E10).Use fuel with the recommendedoctane rating. The engine-specificrequirements are given in the enginedata overview 3 177. A country-specific label at the fuel filler flap cansupersede the requirement.

Caution

Do not use fuel or fuel additivesthat contain metallic compoundssuch as manganese-basedadditives. This may cause enginedamage.


Caution

Use of fuel that does not comply toEN 228 or E DIN 51626-1 orequivalent can lead to deposits orengine damage.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for liquid gas operationLiquid gas is known as LPG(Liquefied Petroleum Gas) or underits French name GPL (Gaz de PétroleLiquéfié). LPG is also known asAutogas.LPG consists mainly of propane andbutane. The octane rating is between105 and 115, depending on thebutane proportion. LPG is storedliquid at around five to ten barpressure.

The boiling point depends on thepressure and mixing ratio. At ambientpressure, it is between -42 °C (purepropane) and -0.5 °C (pure butane).

Caution

The system works at an ambienttemperature of approx. -8 °C to100 °C.

Full function of the LPG system canonly be guaranteed with liquid gaswhich complies with the minimumrequirements of DIN EN 589.

Fuel selector

Pressing LPG switches betweenpetrol and liquid gas operation assoon as the required parameters(coolant temperature, gastemperature and minimum enginespeed) have been reached. Therequirements are usually fulfilled afterapprox. 60 seconds (depending onexterior temperature) and the first firmpress on the accelerator. The LEDstatus shows the current operatingmode.LED off : petrol operationLEDflashes

: checking conditions forfuel transition to liquidgas operation.Illuminates if conditionsare fulfilled.

LED illu‐minates

: liquid gas operation

LEDflashesfivetimesandextin‐guishes

: liquid gas tank is emptyor failure in liquid gassystem. A message isdisplayed in the DriverInformation Centre.

If the fuel tank is empty, the enginewill not start.


The selected fuel mode is stored andreactivated at the next ignition cycle ifconditions allow.As soon as the liquid gas tanks areempty, petrol operation isautomatically engaged until theignition is switched off.When switching automaticallybetween petrol or gas operation, abrief delay of engine tractive powermay be noticeable.Every six months, run the petrol tankdown until control indicator Yilluminates, then refuel. This helpsmaintain fuel quality and systemfunction for petrol operation.Fill the tank completely at regularintervals to prevent corrosion in thetank.

Faults and remediesIf gas mode is not possible, check thefollowing:● Is there enough liquid gas

present?● Is there enough petrol present for

starting?

Due to extreme temperatures incombination with the gascomposition, it may take slightlylonger before the system switchesfrom petrol to gas mode.In extreme situations, the system mayalso switch back to petrol mode if theminimum requirements are notfulfilled. If conditions allow, it might bepossible to manually switch back toliquid gas operation.Seek the assistance of a workshop inthe event of all other faults.

Caution

Repairs and adjustments may onlybe made by trained specialists inorder to maintain the safety andwarranty on the LPG system.

Liquid gas is given a particular odour(odorised) so that any leaks can bedetected easily.

9 Warning

If you smell gas in the vehicle or inthe immediate vicinity, switch topetrol mode immediately. Nosmoking. No naked flames orignition sources.

If the gas odour persists, do not startthe engine. Have the cause of thefault remedied by a workshop.When using underground car parks,follow the instructions of the operatorand local laws.NoticeIn the event of an accident, switch offthe ignition and lights.


Refuelling

9 Danger

Before refuelling, switch offignition and any external heaterswith combustion chambers.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by aworkshop.

Caution

In case of misfuelling, do notswitch on ignition.

1. Stop the engine.

2. Pull up the fuel filler flap releaselever located on the floor, rightfront side of driver's seat.The fuel filler flap is located at rightrear side of the vehicle.

3. Turn the fuel filler capcounterclockwise slowly. If ahissing sound is heard, wait for itto stop before completelyunscrewing the cap.

4. Remove the cap. The cap istethered to the vehicle.


5. After refuelling, replace cap. Turnit clockwise until you hear severalclicks.

6. Push the fuel filler flap closed untilit latches.

NoticeIf, in cold weather, the fuel filler doordoes not open, tap the door lightly.Then try to open it again.

Caution

Wipe off any overflowing fuelimmediately.

Liquid gas refuellingFollow the operating and safetyinstructions of the filling station whenrefuelling.The filling valve for the liquid gas isbehind the fuel filler cap.

Unscrew protective cap from the fillerneck.

Protective cap is magnetic. Place it onfuel filler door while refuelling.

Screw the required adapter hand-tight onto the filler neck.ACME Adapter: Screw the nut of thefilling nozzle onto the adapter. Presslocking lever on filler nozzle down.DISH filler neck: Place the filler nozzleinto the adapter. Press locking leveron filler nozzle down.Bayonet filler neck: Place filler nozzleon the adapter and turn clockwise oranticlockwise through one quarterturn. Pull locking lever of filler nozzlefully.EURO filler neck: Press the fillernozzle onto the adapter until itengages.


Press the button at the liquid gassupply point. The filling system stopsor begins to run slowly when 80% ofthe tank volume is reached(maximum fill level).Release button on filling system andthe filling process stops. Release thelocking lever and remove the fillernozzle. A small quantity of liquid gasmay escape.Remove adapter and stow securely invehicle.Fit protective cap to prevent thepenetration of foreign bodies into thefiller opening and the system.

9 Warning

Due to the system design, anescape of liquid gas afterreleasing the locking lever isunavoidable. Avoid inhaling.

9 Warning

The liquid gas tank should only befilled to 80% capacity, for safetyreasons.

The multivalve on the liquid gas tankautomatically limits the fill quantity. Ifa larger quantity is added, werecommend not exposing the vehicleto the sun until the excess amounthas been used up.

Filling adapterAs filling systems are notstandardised, different adapters arerequired which are available fromVauxhall Distributors and fromVauxhall Authorised Repairers.

ACME adapter: Belgium, Germany,Ireland, Luxembourg, Switzerland

Bayonet adapter: Netherlands,Norway, Spain, United Kingdom

EURO adapter: Spain


DISH adapter: Austria, Bosnia-Herzegovina, Bulgaria, Croatia,Czech Republic, Denmark, Estonia,France, Greece, Hungary, Italy,Latvia, Lithuania, Macedonia,Poland, Portugal, Romania, Serbia,Slovakia, Slovenia, Sweden,Switzerland, Turkey, Ukraine

Fuel filler capOnly use genuine fuel filler caps.

Fuel consumption - CO2-EmissionsThe fuel consumption (combined) ofthe model Vauxhall Viva is within arange of 61.4 to 68.9 mpg.The CO2 emission (combined) iswithin a range of 106 to 94 g/km.For the values specific for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

General informationThe official fuel consumption andspecific CO2 emission figures quotedrelate to the EU base model withstandard equipment.Fuel consumption data and CO2emission data are determinedaccording to regulation R (EC)No. 715/2007 (in the latest applicableversion), taking into consideration thevehicle weight in running order, asspecified by the regulation.

The figures are provided only for thepurpose of comparison betweendifferent vehicle variants and mustnot be taken as a guarantee for theactual fuel consumption of aparticular vehicle. Additionalequipment may result in slightlyhigher results than the statedconsumption and CO2 figures.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.

Vehicle care 131

Vehicle care

General Information ................... 131Accessories and vehiclemodifications .......................... 131

Vehicle storage ........................ 132End-of-life vehicle recovery ..... 132

Vehicle checks ........................... 133Performing work ...................... 133Bonnet ..................................... 133Engine oil ................................. 134Engine coolant ......................... 135Washer fluid ............................ 135Brakes ..................................... 136Brake fluid ............................... 136Vehicle battery ......................... 136Wiper blade replacement ........ 138

Bulb replacement ....................... 138Halogen headlights .................. 139Fog lights ................................. 140Front turn signal lights ............. 141Tail lights ................................. 141Side turn signal lights .............. 142Centre high-mounted brakelight ......................................... 143

Number plate light ................... 143

Interior lights ............................ 144Instrument panel illumination ... 144

Electrical system ........................ 144Fuses ....................................... 144Engine compartment fuse box . 146Instrument panel fuse box ....... 147

Vehicle tools .............................. 149Tools ........................................ 149

Wheels and tyres ....................... 150Winter tyres ............................. 150Tyre designations .................... 150Tyre pressure .......................... 150Tyre pressure monitoringsystem .................................... 151

Tread depth ............................. 155Changing tyre and wheel size . 155Wheel covers ........................... 155Tyre chains .............................. 156Tyre repair kit .......................... 156Wheel changing ....................... 159Spare wheel ............................ 161

Jump starting ............................. 163Towing ....................................... 165

Towing the vehicle ................... 165Appearance care ....................... 166

Exterior care ............................ 166Interior care ............................. 168

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

132 Vehicle care

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:● Wash and wax the vehicle.● Have the wax in the engine

compartment and underbodychecked.

● Clean and preserve the rubberseals.

● Fill up fuel tank completely.● Change the engine oil.● Drain the washer fluid reservoir.● Check the coolant antifreeze and

corrosion protection.● Adjust tyre pressure to the value

specified for full load.● Park the vehicle in a dry, well

ventilated place. Engage first orreverse gear. Prevent the vehiclefrom rolling.

● Do not apply the parking brake.

● Open the bonnet, close all doorsand lock the vehicle.

● Disconnect the clamp from thenegative terminal of the vehiclebattery. Beware that all systemsare not functional, e.g. anti-theftalarm system.

Putting back into operationWhen the vehicle is to be put back intooperation:● Connect the clamp to the

negative terminal of the vehiclebattery. Activate the electronicsof the power windows.

● Check tyre pressure.● Fill up the washer fluid reservoir.● Check the engine oil level.● Check the coolant level.● Fit the number plate if necessary.

End-of-life vehicle recoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite. Only entrust this work to anauthorised recycling centre.

Gas vehicles must be recycled by aservice centre authorised for gasvehicles.

Vehicle care 133

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system usesextremely high voltage. Do nottouch.

BonnetOpening

Pull the release lever and return it toits original position.

Push the safety catch upwards andopen the bonnet.

Secure the bonnet support.

134 Vehicle care

If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to fallinto the latch from a low height(20-25 cm). Check that the bonnet isengaged.

Caution

Do not press the bonnet into thelatch, to avoid dents.

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine.Ensure that the correct specificationof oil is used. Recommended fluidsand lubricants 3 170.The maximum engine oilconsumption is 0.6 l per 1000 km.

Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least five minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.

Caution

It is the owner's responsibility tomaintain the proper level of anappropriate quality oil in theengine.

Insert dipstick to the stop on thehandle and make half a turn.

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atlast change.The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 181.Fit the cap on straight and tighten it.

Vehicle care 135

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C. Innorthern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37 °C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up use a 1:1 mixture ofreleased coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Have

the coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Washer fluid

Fill with clean water mixed with asuitable quantity of approvedwindscreen washer fluid whichcontains antifreeze.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

136 Vehicle care

BrakesIn the event of minimum thickness ofthe brake lining, a squealing noisesounds during braking.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

The brake fluid level must be betweenthe MIN and MAX marks.If fluid level is below MIN seek theassistance of a workshop.Brake and clutch fluid 3 170.

Vehicle batteryThe vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe vehicle battery. Avoid the use ofunnecessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more thanfour weeks can lead to vehicle batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.The anti-theft alarm siren must bedeactivated as follows: Switch theignition on then off, disconnect thevehicle's battery within 15 seconds.Battery discharge protection 3 93.

Vehicle care 137

Replacing the vehicle batteryNoticeAny deviation from the instructionsgiven in this section may lead totemporary deactivation of the stop-start system.

When the vehicle battery is beingreplaced, please ensure that thereare no open ventilation holes in thevicinity of the positive terminal. If aventilation hole is open in this area, itmust be closed off with a dummy cap,and the ventilation in the vicinity of thenegative terminal must be opened.In vehicles with an AGM (AbsorptiveGlass Mat) battery, make sure tohave the battery replaced withanother AGM battery.We recommend the use of an originalVauxhall battery.NoticeUsing an AGM vehicle batterydifferent from the original Vauxhallvehicle battery may result in a lowerperformance.

We recommend that you have thevehicle battery replaced by aworkshop.Stop-start system 3 106.

Charging the vehicle battery

9 Warning

On vehicles with stop-startsystem, ensure that the chargingpotential does not exceed 14.6volts when using a batterycharger. Otherwise the batterymight be damaged.

Jump starting 3 163.

Warning label

Meaning of symbols:● No sparks, naked flames or

smoking.● Always shield eyes. Explosive

gases can cause blindness orinjury.

● Keep the vehicle battery out ofthe reach of children.

● The vehicle battery containssulfuric acid which could causeblindness or serious burninjuries.

138 Vehicle care

● See the Owner's manual forfurther information.

● Explosive gas may be present inthe vicinity of the battery.

Wiper blade replacement

Lift the wiper arm. Press release leverand detach the wiper blade.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Wiper blade on the rear window

Lift wiper arm. Push the wiper blade,slightly angled to the wiper armdownwards until it disengages.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base! Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.

Bulb checkAfter a bulb replacement switch onthe ignition, operate and check thelights.

Vehicle care 139

Halogen headlightsLow beam and high beam

1. On left vehicle side: rotate and pullout the filling pipe of thewindscreen washer fluidcontainer.

2. Remove fuse box cover (left sideof the vehicle only).

3. Press both clips together anddetach plug connector from bulb.

4. Remove protective cover.

5. Press spring clip and disengage.

140 Vehicle care

6. Remove bulb from reflectorhousing.

7. When fitting a new bulb, engagethe lugs in the recesses on thereflector.

8. Engage the spring clip.9. Place headlight protective cover

in position and close.10. Ensure the protective cover is

placed correctly to prevent waterleak and heavy condensations.

Sidelight/Daytime running light1. Remove fuse box cover (left side

of the vehicle only).

2. Rotate the bulb holderanticlockwise and remove.

3. Detach bulb from the bulb holderand replace it.

4. Insert the bulb socket into thereflector and turn clockwise.

Sidelight/daytime running lightwith LEDsSidelights and daytime running lightsare designed as LEDs and cannot bechanged. Consult a workshop in caseof a defective LED.

Fog lights

1. Tilt the wheel and remove the twopush nuts on the outside of thewheel liner.

Vehicle care 141

2. Disconnect the electricalconnector from the bulb holder.

3. Remove the bulb assemblyanticlockwise and pull it straightout.

4. Insert a new bulb assemblystraight into the lamp and rotateclockwise.

5. Reconnect the electricalconnector.

Front turn signal lights

1. Rotate the bulb holderanticlockwise and remove.

2. Rotate bulb anticlockwise andremove from bulb holder.

3. Replace bulb.4. Insert the bulb holder into the

reflector and rotate clockwise.

Tail lightsTail lights, turn signal lights, brakelights and reversing lights

1. Unscrew both screws.2. Remove tail light assembly. Take

care that the cable duct remains inposition.

142 Vehicle care

3. tail light / brake light 1turn signal light 2tail light 3reversing light (passenger side) /rear fog light (driver's side) 4.

4. Rotate bulb holder anticlockwise.

5. Remove bulb holder. Push bulbinto socket slightly, rotate anti-clockwise, remove and renewbulb.

6. Insert bulb holder into the tail lightassembly and screw into place.Connect wiring plug. Install taillight assembly in body and tightenscrews. Close covers andengage.

7. Switch on ignition, operate andcheck all lights.

Side turn signal lightsTo replace bulb, remove lamphousing:

1. Slide lamp to the front and removeit out of the front wing with the rearend.

Vehicle care 143

2. Turn bulb holder anticlockwiseand remove from housing.

3. Pull bulb from bulb holder andreplace it.

4. Insert bulb holder and turnclockwise.

5. Insert front end into front wing,slide forward and insert rear end.

Centre high-mounted brakelight

Have LEDs replaced by a workshop.

Number plate light

1. Unscrew both screws.2. Remove bulb housing

downwards, taking care not to pullon the cable.Rotate bulb holder anticlockwiseto disengage.

3. Remove bulb from bulb holderand replace it.

4. Insert bulb holder into bulbhousing and turn clockwise.

5. Insert bulb housing and secureusing a screwdriver.

144 Vehicle care

Interior lightsCourtesy light, reading lights1. To remove, prise the opposite

side of the lamp switch using aflat-blade screwdriver. (Be carefulnot to make scratches.)

2. Remove the bulb.3. Replace the bulb.4. Reinstall the lamp assembly.

Load compartment light

1. Prise the lamp out with ascrewdriver.

2. Remove bulb.3. Insert new bulb.4. Install lamp.

Instrument panelilluminationHave bulbs replaced by a workshop.

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are two fuse boxes in thevehicle:● In the front left of the engine

compartment.● On the driver's side behind a

cover in the instrument panel.Before replacing a fuse, turn off therespective switch and the ignition.

Vehicle care 145

There are different kinds of fuses inthe vehicle. Some types of fuses inthe vehicle may differ from the onesillustrated.

Depending on the type of fuse, ablown fuse can be recognized by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.

Place the fuse extractor on thevarious types of fuse from the top, andwithdraw fuse.

146 Vehicle care

Engine compartment fusebox

The fuse box is in the front left of theengine compartment.Disengage the cover, lift it upwardsand remove.

No. Circuit

1 Tailgate

2 –

3 Heated rear window

4 Heated exterior mirror

5 Sunroof

6 Transmission control module

7 Engine control module

8 –

9 ABS

10 Body control module, voltage

11 Rear view camera

12 –

13 –

14 Engine control module/Trans‐mission control module

15 Injection system/Starter

16 Fuel pump

17 Engine control module1

Vehicle care 147

No. Circuit

18 Engine control module2

19 Injection system/Ignition

20 Air conditioning system

21 Battery sensor

22 Electric steering column lock

23 Cooling fan low

24 –

25 Exterior mirror switch

26 Engine control module/Manualtransmission automatedmodule

27 Fuel system

28 Brake switch

29 Seat occupancy recognition

30 Headlight range adjustment

31 Horn

32 Front fog light

33 High beam left

No. Circuit

34 High beam right

35 –

36 Rear wiper

37 Cornering light left

38 Washer system

39 Cornering light right

40 –

41 –

42 Starter 2

43 Instrument panel

44 Manual transmission auto‐mated

45 Starter 1

46 ABS

47 Cooling fan high

48 Front wiper

49 Body control module/Retainedpower off

After having changed defective fusesclose the fuse box cover and pressuntil it engages.If the fuse box cover is not closedcorrectly, malfunction may occur.

Instrument panel fuse box

The fuse box is located on the driver'sside behind a cover in the instrumentpanel.To open the compartment, compressthe locking tabs, fold cover down andremove.

148 Vehicle care

No. Circuit

1 Onstar

2 Air conditioning system

3 Instrument panel

4 Transmission control module

5 Infotainment

6 Body control module

7 Rear parking assist

8 Data link connection

9 Electric steering column lock

10 Sensing and Diagnostic module

11 DC transformer

12 –

13 Electronic toll collection system

14 Linear power module

15 Central locking system/Ignitionsystem

16 Ignition system

No. Circuit

17 forward collision alert

18 Instrument panel

19 Forward collision alert indication

20 Headlight range adjustment

21 Power windows, front

22 Power windows, rear

23 –

24 Manual transmission auto‐mated module

25 Auxiliary power outlet

26 Sunroof

27 –

28 Body control module 8





Vehicle care 149

No. Circuit



35 Body control module 1–

36 Ignition system

37 Steering wheel control LED

38 –

39 Logistic/DC transformer

40 Power window, driver

41 Blower

42 Seat heating, front

43 Air conditioning module

44 Heated steering wheel


Vehicle toolsToolsVehicles with tyre repair kit

The vehicle tools are in thecompartment under the floor cover inthe load compartment, together withthe tyre repair kit.

Vehicles with spare wheel

The jack and the vehicle tools are inthe load compartment.

150 Vehicle care

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance of aworkshop in the event of damage orunusual wear.We recommend not swapping thefront wheels with the rear wheels andvice versa, as this can affect vehiclestability. Always use less worn tyreson the rear axle.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 195/55 R 16 95 H195 : tyre width, mm55 : cross-section ratio (tyre height

to tyre width), %R : belt type: RadialRF : type: RunFlat16 : wheel diameter, inches91 : load index e.g. 91 is equivalent

to 615 kgH : speed code letter

Speed code letter:Q : up to 100 mphS : up to 112 mphT : up to 118 mphH : up to 130 mphV : up to 150 mphW : up to 168 mph

Choose a tyre appropriate for themaximum speed of your vehicle.The maximum speed is achievable atkerb weight with driver (75 kg) plus125 kg payload. Optional equipmentcould reduce the maximum speed ofthe vehicle.Performance 3 178.

Directional tyresDirectional tyres must be mounted sothat they rotate in the correctdirection. The proper rotationdirection is indicated by a symbol(e.g. an arrow) on the sidewall.

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey.Do not forget the spare wheel.This also applies to vehicles with tyrepressure monitoring system.Unscrew the valve cap.

Vehicle care 151

Tyre pressure 3 182.The tyre pressure information labelon the driver's door frame indicatesthe original equipment tyres and thecorrespondent tyre pressures.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.Tyre pressures differ depending onvarious options.For the correct tyre pressure value,follow the procedure below:● Identify the engine identifier

code. Engine data 3 177.● Identify the respective tyre.

For the tyres approved for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

The driver is responsible for correctadjustment of tyre pressure.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

9 Warning

For specific tyres therecommended tyre pressure asshown in the tyre pressure tablemay exceed the maximum tyrepressure as indicated on the tyre.Never exceed the maximum tyrepressure as indicated on the tyre.

If the tyre pressure must be reducedor increased, switch off ignition. Afteradjusting tyre pressure switch onignition and select the relevant settingon the page Tyre Load in the DriverInformation Centre 3 73.

Temperature dependencyThe tyre pressure depends on thetemperature of the tyre. Duringdriving, tyre temperature andpressure increase. Tyre pressurevalues provided on the tyreinformation label and tyre pressurechart are valid for cold tyres, whichmeans at 20 °C.The pressure increases by nearly1.5 psi for a 10 °C temperatureincrease. This must be consideredwhen warm tyres are checked.The tyre pressure value displayed inthe Driver Information Centre showsthe real tyre pressure. A cooled downtyre will show a decreased value,which does not indicate an air leak.

Tyre pressure monitoringsystemThe tyre pressure monitoring systemchecks the pressure of all four tyresonce a minute when vehicle speedexceeds a certain limit.

152 Vehicle care

Caution

Tyre pressure monitoring systemwarns only about low tyre pressurecondition and does not replaceregular tyre maintenance by thedriver.

All wheels must be equipped withpressure sensors and the tyres musthave the prescribed pressure.NoticeIn countries where the tyre pressuremonitoring system is legallyrequired, the use of wheels withoutpressure sensors will invalidate thevehicle type approval.

The current tyre pressures can beshown in the Vehicle InformationMenu in the Driver InformationCentre.The menu can be selected bypressing the buttons on the turnsignal lever.

Press MENU to select the VehicleInformation MenuX.

Turn the adjuster wheel to select thetyre pressure monitoring system.

System status and pressure warningsare displayed by a message with thecorresponding tyre flashing in theDriver Information Centre.The system considers the tyretemperature for the warnings.Temperature dependency 3 150.

A detected low tyre pressurecondition is indicated by the controlindicator w 3 71.If w illuminates, stop as soon aspossible and inflate the tyres asrecommended 3 182.

Vehicle care 153

If w flashes for 60-90 seconds thenilluminates continuously, there is afault in the system. Consult aworkshop.After inflating, some driving may berequired to update the tyre pressurevalues in the Driver InformationCentre. During this time w mayilluminate.If w illuminates at lower temperaturesand extinguishes after some driving,this could be an indicator forapproaching a low tyre pressurecondition. Check tyre pressure.Vehicle messages 3 79.If the tyre pressure must be reducedor increased, switch off ignition.Only mount wheels with pressuresensors, otherwise the tyre pressurewill not be displayed and willuminates continuously.A temporary spare wheel is notequipped with pressure sensors. Thetyre pressure monitoring system isnot operational for these tyres.Control indicator w illuminates. Forthe further three tyres, the systemremains operational.

The use of commercially-availableliquid tyre repair kits can impair thefunction of the system. Factory-approved repair kits can be used.Operating electronic devices or beingclose to facilities using similar wavefrequencies could disrupt the tyrepressure monitoring system.Each time the tyres are replaced, tyrepressure monitoring system sensorsmust be dismounted and serviced.For the screwed sensor; replacevalve core and sealing ring. For theclipped sensor; replace completevalve stem.

Vehicle loading statusAdjust tyre pressure to load conditionaccording to the tyre information labelor tyre pressure chart 3 182, andselect the appropriate setting in themenu Tyre Load in the DriverInformation Centre, VehicleInformation Menu 3 73. This setting isthe reference for the tyre pressurewarnings.

The Tyre Load menu only appears ifthe vehicle is in a standstill and theparking brake is applied. On vehicleswith automatic transmission theselector lever has to be in P.

Select:● Lo for comfort pressure up to

3 people.● Eco for Eco pressure up to

3 people.● Hi for full loading.

154 Vehicle care

Tyre pressure sensor matchingprocessEach tyre pressure sensor has aunique identification code. Theidentification code must be matchedto a new tyre/wheel position afterrotating the tyres or exchanging thecomplete wheel set and if one or moretyre pressure sensors were replaced.The tyre pressure sensor matchingprocess should also be performedafter replacing a spare tyre with aroad tyre containing the tyre pressuresensor.The malfunction light w and thewarning message or code should gooff at the next ignition cycle. Thesensors are matched to the wheelpositions, using a relearn tool, in thefollowing order: left side front wheel,right side front wheel, right side rearwheel and left side rear wheel. Theturn signal light at the current activeposition is illuminated until sensor ismatched.Consult a workshop for service orpurchase a relearn tool. There aretwo minutes to match the first wheelposition, and five minutes overall to

match all four wheel positions. If ittakes longer, the matching processstops and must be restarted.The tyre pressure sensor matchingprocess is:1. Apply the parking brake.2. Turn the ignition on.3. On vehicles with manual

transmission automated: Pressand hold brake pedal. Move andhold the selector lever for fiveseconds in position N until P isdisplayed in the DriverInformation Centre. P indicatesthat the sensor matching processcan be started.On vehicles with manualtransmission: select neutral.

4. Use MENU on the turn signallever to select the VehicleInformation Menu in the DriverInformation Centre.

5. Turn the adjuster wheel to scroll tothe tyre pressure menu.

6. Press SET/CLR to begin thesensor matching process. Amessage requesting acceptanceof the process should bedisplayed.

7. Press SET/CLR again to confirmthe selection. The horn soundstwice to indicate that the receiveris in relearn mode.

8. Start with the left side front wheel.9. Place the relearn tool against the

tyre sidewall, near the valve stem.Then press the button to activatethe tyre pressure sensor. A hornchirp confirms that the sensoridentification code has beenmatched to this wheel position.

10. Proceed to the right side frontwheel, and repeat the procedurein Step 9.

11. Proceed to the right side rearwheel, and repeat the procedurein Step 9.

12. Proceed to the left side rearwheel, and repeat the procedurein Step 9. The horn sounds twiceto indicate that the sensoridentification code has been

Vehicle care 155

matched to the left side rearwheel, and the tyre pressuresensor matching process is nolonger active.

13. Turn off the ignition.14. Set all four tyres to the

recommended air pressure levelas indicated on the tyreinformation label.

15. Ensure the tyre loading status isset according to the selectedpressure 3 73.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).For safety reasons it is recommendedthat the tread depth of the tyres onone axle should not vary by more than2 mm.

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wearindicators (TWI). Their position isindicated by markings on thesidewall.Tyres age, even if they are not used.We recommend tyre replacementevery 6 years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme the

speedometer as well as the nominaltyre pressure and to make othervehicle modifications.After converting to a different tyresize, have the label with tyrepressures replaced.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

156 Vehicle care

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Tyre chains

Tyre chains are only permitted on thefront wheels.Always use fine mesh chains that addno more than 10 mm to the tyre treadand the inboard sides (including chainlock).

9 Warning

Damage may lead to tyre blowout.

Tyre chains are only permitted ontyres of size 165/65 R14.Tyre chains are not permitted on tyresof size 185/55 R15 and 195/45 R16.The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at the tyre's sidewall cannot berepaired with the tyre repair kit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear or reverse gear.

The tyre repair kit is in the tool boxunder the floor cover in the loadcompartment.

Vehicle care 157

1. Open the floor cover.

2. Remove the compressor and thesealant bottle.

3. Remove the electrical connectioncable and air hose from thestorage compartments on theunderside of the compressor.

4. Screw the compressor air hose tothe connection on the sealantbottle.

5. Fit the sealant bottle into theretainer on the compressor.Set the compressor near the tyrein such a way that the sealantbottle is upright.

6. Unscrew valve cap from defectivetyre.

7. Screw the filler hose to the tyrevalve.

8. The switch on the compressormust be set to J.

9. Connect the compressor plug tothe power outlet or cigarettelighter socket.To avoid discharging the battery,we recommend running theengine.

158 Vehicle care

Set the rocker switch on thecompressor to I. The tyre is filledwith sealant.

10. The compressor pressure gaugebriefly indicates up to six barwhilst the sealant bottle isemptying (approx. 30 seconds).Then the pressure starts to drop.

11. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

12. The prescribed tyre pressureshould be obtained within tenminutes. Tyre pressure 3 182.When the correct pressure isobtained, switch off thecompressor.

If the prescribed tyre pressure isnot obtained within ten minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure forten minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.Drain excess tyre pressure withthe button over the pressureindicator.Do not run the compressor forlonger than ten minutes.

13. Detach the tyre repair kit. Pushcatch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

14. Remove any excess sealantusing a cloth.

15. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

16. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.six miles (but no more than tenminutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.

Vehicle care 159

If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

17. Stow away tyre repair kit in loadcompartment.Reinstall floor cover. Rear floorstorage cover 3 53.

NoticeThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.

If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens at apressure of seven bar (102 psi).Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Wheel changingSome vehicles are equipped with atyre repair kit instead of a sparewheel.

Make the following preparations andobserve the following information:● Park the vehicle on a level, firm

and non-skid surface. The frontwheels must be in the straight-ahead position.

● Apply the parking brake andengage first gear or reverse gear.

● Never change more than onewheel at once.

● Use the jack only to changewheels in case of puncture, notfor seasonal winter or summertyre change.

● The jack is maintenance-free.● If the ground on which the vehicle

is standing is soft, a solid board(max. 1 cm thick) should beplaced under the jack.

● Take heavy objects out of thevehicle before jacking up.

● No people or animals may be inthe vehicle when it is jacked-up.

● Never crawl under a jacked-upvehicle.

160 Vehicle care

● Do not start the vehicle when it israised on the jack.

● Clean wheel nuts and thread witha clean cloth before mounting thewheel.

9 Warning

Do not grease wheel bolt, wheelnut and wheel nut cone.

1. Steel wheels:Pull off the wheel cover.Alloy wheels with bolt capsDisengage wheel bolt caps with ascrewdriver and remove. Toprotect the wheel, place a softcloth between the screwdriverand the alloy wheel.Alloy wheels with centre capInsert extractor in the open slot ofthe centre cap and remove thecap from the wheel. Vehicle tools3 149.

2. Install the wheel wrench ensuringthat it locates securely and looseneach wheel bolt by half a turn.The wheels might be protected bylocking wheel bolts. To loosenthese specific bolts, first attachthe adapter for the locking wheelbolts onto the head of the boltbefore installing the wheelwrench. The adapter is located inthe glovebox.

3. Ensure the jack is correctlypositioned under the relevantvehicle jacking point.

4. Set the jack to the necessaryheight. Position it directly below

Vehicle care 161

the jacking point in a manner thatprevents it from slipping.Attach jack handle and with thejack correctly aligned rotatehandle until wheel is clear of theground.

5. Unscrew the wheel bolts.6. Change the wheel.7. Screw on the wheel bolts.8. Lower vehicle.9. Install the wheel wrench ensuring

that it locates securely and tighteneach bolt in a crosswisesequence. Tightening torque is140 Nm.

10. Align the valve hole in the wheelcover of the steel wheel with thetyre valve before installing.Install wheel bolt caps or centrecap on alloy wheel.

11. Stow and secure the replacedwheel, the vehicle tools 3 149 andthe adapter for the locking wheelbolts 3 49.

12. Check the tyre pressure of theinstalled tyre and the wheel bolttorque as soon as possible.

Have the defective tyre renewed orrepaired as soon as possible.

Jacking position for lifting platform

Rear arm position of the liftingplatform, located centrally under therecess of the sill.

Front arm position of the liftingplatform at the underbody.

Spare wheelSome vehicles are equipped with atyre repair kit instead of a sparewheel.If mounting a spare wheel, which isdifferent from the other wheels, thiswheel might be classified as atemporary spare wheel and thecorresponding speed limits apply,even though no label indicates this.Seek the assistance of a workshop tocheck the applicable speed limit.The spare wheel has a steel rim.

162 Vehicle care

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

The spare wheel is located in the loadcompartment beneath the floorcovering. It is secured in the recesswith a wing bolt.The spare wheel well is not designedfor all permitted tyre sizes. If a wheelwider than the spare must be stowed

in the spare wheel well after changingwheels, the floor cover can be placedon the projecting wheel.

Temporary spare wheel

Caution

The use of the temporary sparewheel could affect driveability.Have the defective tyre renewedor repaired as soon as possible.

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel inthe front and the full size tyre in therear.Tyre chains 3 156.

Storing a damaged wheel in theload compartment using a strapUse the strap placed in the tool box.Vehicle tools 3 149.

1. Remove load compartment coverand lift up load compartment floor.Position the tool box and thedamaged wheel to stand uprightinto the tool box spare.

2. Pull up the release knob on top ofthe rear seat and move backrestforwards.

3. Place the loop end of the strapfrom the tool box through thebackrest latch.

4. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe backrest latch.

Vehicle care 163

5. Pull back the backrests.6. Mount the hook to the tailgate

latch.7. Tighten the strap and secure it

using the buckle.

9 Warning

Storing a jack, a wheel or otherequipment in the loadcompartment could cause injury ifthey are not fixed properly. Duringa sudden stop or a collision, looseequipment could strike someone.

Store jack and tools always in therespective storage compartmentsand secure them by fixing.Damaged wheel placed in the loadcompartment must always besecured by the strap.

Jump startingDo not start with a quick charger.A vehicle with a discharged vehiclebattery can be started using jumpleads and the vehicle battery ofanother vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

● Never expose the battery tonaked flames or sparks.

164 Vehicle care

● A discharged vehicle battery canalready freeze at a temperatureof 0 °C. Defrost the frozen batterybefore connecting jump leads.

● Wear eye protection andprotective clothing whenhandling a battery.

● Use a booster battery with thesame voltage (12 Volts). Itscapacity (Ah) must not be muchless than that of the dischargedbattery.

● Use jump leads with insulatedterminals and a cross section ofat least 16 mm2.

● Do not disconnect the dischargedvehicle battery from the vehicle.

● Switch off all unnecessaryelectrical consumers.

● Do not lean over the batteryduring jump starting.

● Do not allow the terminals of onelead to touch those of the otherlead.

● The vehicles must not come intocontact with each other duringthe jump starting process.

● Apply the parking brake,transmission in neutral.

● Open the positive terminalprotection caps of both vehiclebatteries.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery.

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedvehicle battery as possible,however at least 60 cm.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After five minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval ofone minute.

3. Allow both engines to idle forapprox. three minutes with theleads connected.

Vehicle care 165

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

TowingTowing the vehicleThe towing eye is stowed with thevehicle tools 3 149.

1. Disengage cap by using thescrewdriver and remove the cap.

2. Screw in the towing eye as far asit will go until it stops in ahorizontal position.

3. Attach a tow rope – or better still atow rod – to the towing eye.

GeneralThe towing eye must only be used fortowing and not for recovering thevehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.

166 Vehicle care

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.The vehicle must be towed facingforward, not faster than 88 km/h. In allother cases and when thetransmission is defective, the frontaxle must be raised off the ground.Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap and engage in the frontbumper.

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use a de-icing agent onlywhen absolutely necessary, as thishas a degreasing effect and impairslock function. After using a de-icingagent, have the locks regreased by aworkshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.

If using a car wash, comply with thecar wash manufacturer's instructions.The windscreen wiper and rearwindow wiper must be switched off.Remove antenna and externalaccessories such as roof racks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.Clean bright metal mouldings with acleaning solution approved foraluminium to avoid damages.

Caution

Always use a cleaning agent witha pH value of four to nine.Do not use cleaning agents on hotsurfaces.

Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.

Vehicle care 167

Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax painted parts of the vehicleregularly (at the latest when water nolonger beads). Otherwise, thepaintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone forms aprotective film, making waxingunnecessary.Unpainted plastic body parts must notbe treated with wax or polishingagents.

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window frominside, always wipe in parallel to theheating element to prevent damage.For mechanical removal of ice, use asharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Clean smearing wiper blades with asoft cloth and window cleaner.

SunroofNever clean with solvents or abrasiveagents, fuels, aggressive media (e.g.paint cleaner, acetone-containingsolutions etc.), acidic or highlyalkaline media or abrasive pads. Donot apply wax or polishing agents tothe sunroof.

Wheels and tyresDo not use high-pressure jetcleaners.

Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out by aworkshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

168 Vehicle care

Liquid gas system

9 Danger

Liquid gas is heavier than air andcan collect in sink points.Take care when performing workat the underbody in a pit.

For painting work and when using adrying booth at a temperature above60 °C, the liquid gas tank must beremoved.Do not make any modifications to theliquid gas system.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.

The instrument cluster and thedisplays should only be cleaned usinga soft damp cloth. If necessary use aweak soap solution.Clean fabric upholstery with avacuum cleaner and brush. Removestains with an upholstery cleaner.Clothing fabrics may not becolourfast. This could cause visiblediscolourations, especially on light-coloured upholstery. Removablestains and discolourations should becleaned as soon as possible.Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

Service and maintenance 169

Service andmaintenance

General information ................... 169Service information .................. 169

Recommended fluids, lubricantsand parts .................................... 170

Recommended fluids andlubricants ................................ 170

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 64.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.A shorter service interval can be validfor severe driving behaviour, e.g. fortaxis and police vehicles.The European service intervals arevalid for the following countries:

Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,Liechtenstein, Lithuania,Luxembourg, Macedonia, Malta,Monaco, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,San Marino, Serbia, Slovakia,Slovenia, Spain, Sweden,Switzerland, United Kingdom.Service display 3 64.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or afterone year, whichever occurs first,unless otherwise indicated in theservice display.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 64.

170 Service and maintenance

ConfirmationsConfirmation of service is recorded inthe Service and Warranty Booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.Make sure that the Service andWarranty Booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 64.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that meet therecommended specifications.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oilaging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.

Dexos is the newest engine oil qualitythat provides optimum protection forpetrol engines. If it is unavailable,engine oils of other listed qualitieshave to be used. Recommendationsfor petrol engines are also valid forLiquified Petroleum Gas (LPG) andEthanol (E85) fuelled engines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 174.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 174.

Service and maintenance 171

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 174.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only silicate-free long life coolant(LLC) antifreeze approved for thevehicle. Consult a workshop.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -36 °C. In

northern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -50 °C. This concentrationshould be maintained all year round.The use of additional coolantadditives that intend to give additionalcorrosion protection or seal againstminor leaks can cause functionproblems. Liability for consequencesresulting from the use of additionalcoolant additives will be rejected.

Brake and clutch fluidOver time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.

172 Technical data

Technical data

Vehicle identification .................. 172Vehicle Identification Number .. 172Identification plate ................... 173Engine identification ................ 173

Vehicle data ............................... 174Recommended fluids andlubricants ................................ 174

Engine data ............................. 177Performance ............................ 178Vehicle weight ......................... 179Vehicle dimensions ................. 180Capacities ................................ 181Tyre pressures ........................ 182

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Number islocated in the engine compartment.

The Vehicle Identification Numbermay be embossed on the instrumentpanel, visible through the windscreen.

Technical data 173

Identification plate

The identification plate is located onthe left door frame.

Information on identification label:1 : manufacturer2 : type approval number3 : vehicle identification number4 : permissible gross vehicle weight

rating in kg5 : permissible gross train weight

in kg6 : maximum permissible front axle

load in kg7 : maximum permissible rear axle

load in kg

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.Specifications in the vehicledocuments always have priority overthose given in this manual.

Engine identificationThe technical data tables use theengine identifier code. Engine data3 177.To identify the respective engine,refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.The Certificate of Conformity showsthe engine identifier code, othernational publications may show theengineering code. Check pistondisplacement and engine power toidentify the respective engine.

174 Technical data

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries with European service interval 3 169

Engine oil quality Petrol engines(including LPG, E85)

dexos 1 –

dexos 2 ✔

In case dexos quality is unavailable, you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.

Engine oil viscosity gradesAll European countries with European service interval 3 169

Ambient temperature Petrol engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

Technical data 175

International service schedule

Required engine oil qualityAll countries with international service interval 3 169


dexos 1 (if available) ✔

dexos 2 ✔

In case dexos quality is unavailable, you may use the oil qualities listed below:

All countries with international service interval 3 169


GM-LL-A-025 ✔

GM-LL-B-025 –



ACEA A3/B3 ✔

ACEA A3/B4 ✔

176 Technical data


ACEA C3 ✔

API SM ✔

API SN resource conserving ✔

Engine oil viscosity gradesAll countries with international service interval 3 169

Ambient temperature Petrol engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-40

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

Technical data 177

Engine dataEngine identifier code B10XE B10XL LPGSales designation 1.0 1.0 LPG

Piston displacement [cm3] 999 999

Engine power [kW] 55 54

at rpm 6500 6500

Torque [Nm] 95 92

at rpm 4500 4500

Fuel type Petrol Liquid gas/Petrol

Octane rating RON2)

recommended 95 95

possible 91 91

possible 98 98

Additional fuel type – Liquid gas (LPG)

2) A country-specific label at the fuel filler flap can supersede the engine specific requirement.

178 Technical data

PerformanceEngine B10XE B10XL LPG

Maximum speed [mph]

Manual transmission 105 105

Manual transmission automated 105 –

Automatic transmission – –

Technical data 179

Vehicle weightKerb weight

Engine Manual transmission Manual transmission automated Automatic transmission

minimum / maximum[kg]

B10XE 939 / 1034 939/1034 –

B10XL LPG 1025/1091 – –

Optional accessories increase the kerb weight.Loading information 3 54.

180 Technical data

Vehicle dimensionsLength [mm] 3675

Width without exterior mirrors [mm] 1595

Width with two exterior mirrors [mm] 1876

Height (without antenna) [mm] without roof rack 1485

Length of load compartment floor [mm] 486

Length of load compartment with folded rear seats [mm] 1109

Load compartment width [mm] 968

Load compartment height with cover [mm] 499

Height of load compartment opening [mm] 608

Wheelbase [mm] 2385

Turning circle diameter [m]3) 9.6 - 10.4

3) Depending on body- and equipment variants.

Technical data 181

CapacitiesEngine oil

Engine B10XEB10XL LPG

including Filter [l] 4.0

between MIN and MAX [l] 1.0

Fuel tank

Engine B10XE B10XL LPG

Petrol, refilling quantity [l] 32 32

LPG, refilling quantity [l] – 25

182 Technical data

Tyre pressuresComfort with up to 3people ECO with up to 3 people

With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

B10XE,B10XL LPG

165/65 R14,185/55 R15,195/45 R16

220/2.2 (32) 210/2.1 (30) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 300/3.0 (44)

Temporary spare wheelT105/70D14

420/4.2 (60)

Customer information 183

Customerinformation

Customer information ................ 183Declaration of conformity ......... 183Collision damage repair ........... 185Software acknowledgement .... 185

Vehicle data recording and pri‐vacy ........................................... 187

Event data recorders ............... 187Radio Frequency Identification(RFID) ..................................... 188

Customer informationDeclaration of conformityTransmission systemsThis vehicle has systems thattransmit and/or receive radio wavessubject to Directive 1999/5/EC.These systems are in compliancewith the essential requirements andother relevant provisions of Directive1999/5/EC. Copies of the originalDeclarations of Conformity can beobtained on our website.

184 Customer information

Jack


Translation of the original declarationof conformityDeclaration of conformity accordingto EC Directive 2006/42/ECWe declare that the product:Product designation: JackType/GM part number: 13584087is in compliance with the provisions ofDirective 2006/42/EC.Applied technical standards:GM 14337 : standard equipment

jack – hardware testsGMW15005 : standard equipment

jack and spare tyre,vehicle test

The person authorised to compile thetechnical documentation isHans-Peter MetzgerEngineering Group Manager Chassis& StructureAdam Opel AGD-65423 Rüsselsheim

Signed byDaehyeok AnEngineering Group Manager TyreWheel SystemsGM KoreaBupyung, Incheon, 403-714, KoreaIncheon, Republic of Korea, 4th April2014

Collision damage repairPaint thicknessDue to production techniques, thethickness of the paint can varybetween 50 and 400 µm.Therefore, different paint thickness isno indicator for a collision damagerepair.

Software acknowledgementCertain OnStar components includelibcurl and unzip software and otherthird party software. Below are thenotices and licenses associated withlibcurl and unzip and for other thirdparty software please see http://www.lg.com/global/support/opensource/index.

libcurlCopyright and permission noticeCopyright (c) 1996 - 2010, DanielStenberg, <[email protected]>.All rights reserved.Permission to use, copy, modify, anddistribute this software for anypurpose with or without fee is herebygranted, provided that the abovecopyright notice and this permissionnotice appear in all copies.The software is provided "as is",without warranty of any kind, expressor implied, including but not limited tothe warranties of merchantability,fitness for a particular purpose andnoninfringement of third party rights.In no event shall the authors or


copyright holders be liable for anyclaim, damages or other liability,whether in an action of contract, tortor otherwise, arising from, out of or inconnection with the software or theuse or other dealings in the software.Except as contained in this notice, thename of a copyright holder shall notbe used in advertising or otherwise topromote the sale, use or otherdealings in this Software without priorwritten authorization of the copyrightholder.

unzipThis is version 2005-Feb-10 of theInfo-ZIP copyright and license. Thedefinitive version of this documentshould be available at ftp://ftp.info-zip.org/pub/infozip/license.htmlindefinitely.Copyright (c) 1990-2005 Info-ZIP. Allrights reserved.For the purposes of this copyright andlicense, “Info-ZIP” is defined as thefollowing set of individuals:Mark Adler, John Bush, Karl Davis,Harald Denker, Jean-Michel Dubois,Jean-loup Gailly, Hunter Goatley, Ed

Gordon, Ian Gorman, Chris Herborth,Dirk Haase, Greg Hartwig, RobertHeath, Jonathan Hudson, PaulKienitz, David Kirschbaum, JohnnyLee, Onno van der Linden, IgorMandrichenko, Steve P. Miller, SergioMonesi, Keith Owens, GeorgePetrov, Greg Roelofs, Kai UweRommel, Steve Salisbury, DaveSmith, Steven M. Schweda, ChristianSpieler, Cosmin Truta, AntoineVerheijen, Paul von Behren, RichWales, Mike White.This software is provided “as is,”without warranty of any kind, expressor implied. In no event shall Info-ZIPor its contributors be held liable forany direct, indirect, incidental, specialor consequential damages arising outof the use of or inability to use thissoftware.Permission is granted to anyone touse this software for any purpose,including commercial applications,and to alter it and redistribute it freely,subject to the following restrictions:

1. Redistributions of source codemust retain the above copyrightnotice, definition, disclaimer, andthis list of conditions.

2. Redistributions in binary form(compiled executables) mustreproduce the above copyrightnotice, definition, disclaimer, andthis list of conditions indocumentation and/or othermaterials provided with thedistribution. The sole exception tothis condition is redistribution of astandard UnZipSFX binary(including SFXWiz) as part of aself-extracting archive; that ispermitted without inclusion of thislicense, as long as the normalSFX banner has not beenremoved from the binary ordisabled.

3. Altered versions--including, butnot limited to, ports to newoperating systems, existing portswith new graphical interfaces, anddynamic, shared, or static libraryversions--must be plainly markedas such and must not bemisrepresented as being the


original source. Such alteredversions also must not bemisrepresented as being Info-ZIPreleases--including, but notlimited to, labeling of the alteredversions with the names “Info-ZIP” (or any variation thereof,including, but not limited to,different capitalizations), “PocketUnZip,” “WiZ” or “MacZip” withoutthe explicit permission of Info-ZIP.Such altered versions are furtherprohibited from misrepresentativeuse of the Zip-Bugs or Info-ZIP e-mail addresses or of the Info-ZIPURL(s).

4. Info-ZIP retains the right to usethe names “Info-ZIP,” “Zip,”“UnZip,” “UnZipSFX,” “WiZ,”“Pocket UnZip,” “Pocket Zip,” and“MacZip” for its own source andbinary releases.

Vehicle data recordingand privacyEvent data recordersData storage modules in thevehicleA large number of electroniccomponents of your vehicle containdata storage modules temporarily orpermanently storing technical dataabout the condition of the vehicle,events and errors. In general, thistechnical information documents thecondition of parts, modules, systemsor the environment:● Operating conditions of system

components (e.g. filling levels).● Status messages of the vehicle

and its single components (e.g.number of wheel revolutions /rotational speed, deceleration,lateral acceleration).

● Dysfunctions and defects inimportant system components.

● Vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of thestability regulation system).

● Environmental conditions (e.g.temperature).

These data are exclusively technicaland help identifying and correctingerrors as well as optimizing vehiclefunctions.Motion profiles indicating travelledroutes cannot be created with thesedata.If services are used (e.g. repairworks, service processes, warrantycases, quality assurance),employees of the service network(manufacturer included) are able toread out this technical informationfrom the event and error data storagemodules applying special diagnosticdevices. If required, you will receivefurther information at theseworkshops. After an error has beencorrected, the data are deleted fromthe error storage module or they areconstantly overwritten.


When using the vehicle, situationsmay occur in which these technicaldata related to other information(accident report, damages on thevehicle, witness statements etc.) maybe associated with a specific person -possibly, with the assistance of anexpert.Additional functions contractuallyagreed upon with the client (e.g.vehicle location in emergency cases)allow the transmission of particularvehicle data from the vehicle.

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyrepressure monitoring and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

190

Index AAccessories and vehicle

modifications .......................... 131Adjustable air vents ................... 100Airbag and belt tensioners ........... 68Airbag deactivation ................ 42, 68Airbag label................................... 37Airbag system .............................. 37Air conditioning regular

operation ................................ 101Air conditioning system ................ 95Air intake .................................... 101Air vents...................................... 100Antilock brake system ................ 114Antilock brake system (ABS) ....... 70Anti-theft alarm system ................ 25Appearance care........................ 166Ashtrays ....................................... 61Autostop..................................... 106

BBattery discharge protection ........ 93Battery voltage ............................. 81Belts.............................................. 35Bonnet ....................................... 133Bonnet open................................. 72Brake and clutch fluid................. 170Brake and clutch system ............. 69Brake assist ............................... 115Brake fluid .................................. 136

Brakes ............................... 114, 136Breakdown.................................. 165Bulb replacement ....................... 138

CCapacities .................................. 181Catalytic converter ..................... 110Central locking system ................ 21Centre console storage ............... 50Centre high-mounted brake light 143Changing tyre and wheel size . . . 155Charging system .......................... 69Child locks ................................... 23Child restraint installation

locations ................................... 45Child restraints.............................. 43Child restraint systems ................ 43Cigarette lighter ........................... 61City mode................................... 118Climate control ............................. 15Climate control systems............... 94Clock ............................................ 59Code............................................. 79Collision damage repair.............. 185Control indicators.......................... 65Control of the vehicle ................. 103Controls........................................ 57Coolant and antifreeze............... 170Cornering lights............................ 89Cruise control ...................... 72, 119

191

Cupholders .................................. 49Curtain airbag system .................. 41

DDanger, Warnings and Cautions . . . 4Daytime running lights ................. 89Declaration of conformity............ 183Door open .................................... 73Doors............................................ 24Driver assistance systems.......... 119Driver Information Centre............. 73Driving hints................................ 103

EElectric adjustment ...................... 26Electrical system......................... 144Electronic climate control system 97Electronic driving programmes . . 113Electronic Stability Control.......... 117Electronic Stability Control and

Traction Control system............ 70Electronic Stability Control off....... 70End-of-life vehicle recovery ....... 132Engine compartment fuse box ... 146Engine coolant ........................... 135Engine coolant temperature ........ 71Engine coolant temperature

gauge ....................................... 64Engine data ............................... 177Engine exhaust .......................... 110Engine identification................... 173

Engine oil ................... 134, 170, 174Engine oil pressure ...................... 71Event data recorders.................. 187Exit lighting .................................. 93Exterior care .............................. 166Exterior light ................................. 72Exterior lighting ...................... 12, 88Exterior mirrors............................. 26

FFault ........................................... 113First aid......................................... 54First aid kit ................................... 54Fixed air vents ........................... 101Fog light ....................................... 72Fog lights ................................... 140Folding mirrors ............................. 26Front airbag system ..................... 40Front fog lights ............................. 90Front seats.................................... 32Front turn signal lights ............... 141Fuel............................................. 124Fuel consumption - CO2-

Emissions ............................... 130Fuel for liquid gas operation....... 125Fuel for petrol engines ............... 124Fuel gauge ................................... 62Fuel selector ................................ 63Fuses ......................................... 144

GGauges......................................... 61Gear shifting................................. 70Glovebox ..................................... 49

HHalogen headlights .................... 139Hand brake......................... 114, 115Hazard warning flashers .............. 89Headlight flash ............................. 88Headlight range adjustment ........ 89Headlights..................................... 88Headlights when driving abroad . . 89Head restraint adjustment ............. 8Head restraints ............................ 31Heated mirrors ............................. 26Heated rear window ..................... 29Heated steering wheel ................. 57Heating ........................................ 34Heating and ventilation system . . . 94High beam ............................. 72, 88Hill start assist ........................... 115Horn ....................................... 13, 58

IIdentification plate ..................... 173Ignition switch positions ............. 104Immobiliser ............................ 25, 72Indicators...................................... 61Info display................................... 78Information displays...................... 73

192

Instrument cluster ........................ 61Instrument panel fuse box ......... 147Instrument panel illumination ..... 144Instrument panel illumination

control ...................................... 91Instrument panel overview ........... 10Interior care ............................... 168Interior lighting.............................. 91Interior lights ........................ 92, 144Interior mirrors.............................. 27Introduction .................................... 3ISOFIX child restraint systems .... 48

JJump starting ............................. 163

KKey, memorised settings.............. 21Keys ............................................. 19Keys, locks................................... 19

LLane departure warning....... 70, 123Light switch .................................. 88Load compartment ................ 24, 50Load compartment cover ............. 52Loading information ..................... 54Low fuel ....................................... 72

MMalfunction indicator light ............ 69Manual anti-dazzle ...................... 27Manual mode ............................. 113Manual transmission .................. 110Manual transmission automated 111Manual windows .......................... 27Memorised settings...................... 21Mirror adjustment ........................... 8Mirrors ......................................... 26Misted light covers ....................... 91

NNew vehicle running-in .............. 104Number plate light ..................... 143

OObject detection systems........... 122Odometer ..................................... 62Oil, engine.......................... 170, 174OnStar.......................................... 84Operate pedal............................... 69Outside temperature .................... 59Overrun cut-off ........................... 106

PParking ................................ 18, 109Parking assist ............................ 122Parking brake ............................ 115Parking lights ............................... 91Performance .............................. 178

Performing work ........................ 133Pollen filter ................................. 101Power outlets ............................... 61Power steering.............................. 70Power windows ............................ 28Puncture..................................... 159

RRadio Frequency Identification

(RFID)..................................... 188Radio remote control ................... 20Reading lights .............................. 92Rear floor storage cover .............. 53Rear fog light ......................... 72, 90Rear window wiper/washer .......... 59Recommended fluids and

lubricants ........................ 170, 174Reduced engine power................ 72Refuelling ................................... 127Retained power off..................... 105Reversing lights ........................... 91Ride control systems.................. 116Roof.............................................. 29Roof load...................................... 54

SSafety belts................................... 35Seat adjustment ....................... 7, 33Seat belt ........................................ 8Seat belt reminder ....................... 68Seat belts ..................................... 35

193

Seat heating................................. 34Seat position ................................ 32Selector lever ............................. 112Service ....................................... 102Service display ............................ 64Service information .................... 169Service vehicle soon .................... 69Side airbag system ...................... 41Sidelights...................................... 88Side turn signal lights ................ 142Software acknowledgement....... 185Spare wheel ............................... 161Speed limiter......................... 72, 121Speedometer ............................... 61Starting and operating................ 104Starting off ................................... 16Starting the engine ............ 105, 111Steering...................................... 104Steering wheel adjustment ...... 9, 57Steering wheel controls ............... 57Stop-start system........................ 106Storage......................................... 49Storage compartments................. 49Sunroof ........................................ 29Sun visors .................................... 29Symbols ......................................... 4

TTachometer ................................. 62Tail lights ................................... 141

Three-point seat belt .................... 36Tools .......................................... 149Top-tether fastening eyes ............ 48Towing........................................ 165Towing the vehicle ..................... 165Traction Control system ............. 116Traction Control system off........... 71Transmission ............................... 15Transmission display ................. 111Tread depth ............................... 155Trip odometer .............................. 62Turn and lane-change signals ..... 90Turn signal ................................... 67Tyre chains ................................ 156Tyre designations ...................... 150Tyre pressure ............................ 150Tyre pressure monitoring

system............................... 71, 151Tyre pressures ........................... 182Tyre repair kit ............................. 156

UUltrasonic parking assist ...... 70, 122Upholstery.................................. 168Using this manual .......................... 3

VValet mode................................... 78Vehicle battery ........................... 136Vehicle checks............................ 133Vehicle data................................ 174

Vehicle data recording andprivacy..................................... 187

Vehicle dimensions .................... 180Vehicle Identification Number .... 172Vehicle jack................................ 149Vehicle messages ....................... 79Vehicle personalisation ............... 82Vehicle specific data ...................... 3Vehicle storage........................... 132Vehicle tools............................... 149Vehicle unlocking ........................... 6Vehicle weight ........................... 179Ventilation..................................... 94

WWarning chimes ........................... 81Warning lights............................... 61Warning triangle .......................... 53Washer and wiper systems ......... 13Washer fluid ............................... 135Wheel changing ......................... 159Wheel covers ............................. 155Wheels and tyres ....................... 150Windows....................................... 27Windscreen................................... 27Windscreen wiper/washer ........... 58Winter tyres ............................... 150Wiper blade replacement .......... 138

Copyright by General Motors UK Ltd.

The information contained in this publication is effective as of the date indicated below. General Motors UK Ltd. reserves the rightto make changes to the technical specifications, features and design of the vehicles relative to the information contained in thispublication, as well as changes to the publication itself.

Edition: January 2016, General Motors UK Ltd.

Printed on chlorine-free bleached paper.

*KTA-2779/3-VX-EN*

KTA-2779/3-VX-en 01/2016

vauxhall viva owner's manual...or front or back, always relate to the direction of travel....

Documents