variable speed drive sd250 - power electronics sd250/02 caracteristic… · • ranging from 0.4kw...
TRANSCRIPT
32-33
• Ranging from 0.4kW to 22kW, 200-230V and 380-480 Vac• Easy programming and monitoring through cursors and digital display, removable up to 5m• Wide range of accessories: RFI filter, harmonic filters, dV/dt output filter, Profibus gateway, Ethernet gateway and DeviceNET module• Conformally coated electronics, IP20 protection and operation up to 50° C• 3 year warranty and 24h service and replacement commitment
SD250VARIABLESPEED DRIVE
The SD250 series from Power Electronics is a compact and versatile variable speed drive suitable for multiple low power applications, by offering a competitive solution where many units are required.
Divided in six frame sizes, this intuitive VSD covers a range from 0.4kW to 22kW and offers a wide range of accessories such as RFI filter, filters dV/dt, input filters and display extension kits that complete its standard features.
Our technicians will give you telephonic assistance 24h/7d during installation and commissioning, and if necessary our committment to repair or replace the unit guarantees the success of your operation.
05.
SD25
0 S
ER
IES
THE MOST PROFITABLE SOLUTION TAILORED
YOUR FACILITIES
34-35
Discovering SD250
DISPLAYEXTENSION KITSD250 offers the possibility to install the display up to 5m away from the drive. Install SD250 display in the front door of the cabinet and you can safely operate the unit.
EASY LOCAL ANDREMOTE USEDThanks to its intuitive programming console the commissioning process becomes simple.
By using the Modbus-RTU (RS-485) serial communication, you will be able to check the operating status (voltage, current, frequency, etc) and to modify the running parameters of your system (frequency ramp, max. frequency, PID reference, etc.).
Protects the sensitive electronic equipment from moisture, dust and corrosive gases, reducing maintenance and increasing their reliability.
CONFORMAL COATING
PARAMETER READING, COPYING AND WRITING FUNCTIONS ALLOW
A QUICK AND EASY PROGRAMMING OF MULTIPLE UNITS
Two holes allow the user to screw the unit to a panel mounted in your cabinet. The rear cooling fans can be easily removable from the bottom part and the front connections reducing wiring complexity.
EASY INSTALLATION AND SERVICING
05.
SD25
0 S
ER
IES
SEGMENTS DISPLAY
LOCAL STOP/ RESET
CURSOR
STATUSINDICATION LEDS
INTEGRATED MEMORY
RUN
DISPLAY DESCRIPTION
BU
TTO
N
RUN Run command
STOP/RESET Stop command. Reset faults
Parameters scrolling
Parameters scrolling
Groups scrolling
Groups scrolling
Confirmation and enter
LED
FWD Lit during forward run
REV Lit during reverse run
RUN Lit during operation
SET Lit during parameter
APPLICATIONS. The SD250 variable speed drives from Power Electronics are designed to cover a wide range of applications. They are suitable for industries such as water treatment, food and beverage, ventilation systems, material processing, lifting systems, textiles, plastic, wood and chemistry.
LOW VOLTAGE / POWER ELECTRONICS
36-3636-37
Control and precisionThe SD250 is present in all industries, where motor protection, high accuracy and easy to install are the minimum requirements of system integrators or original equipment manufacturers.
The open-loop vector control provides excellent control as well as powerful torque.
ROBUST DESIGN AND EASY INSTALLATIONThe SD250 series of Power Electronics can operate at temperatures up to 50°C without derating or 150% overload, enabling its use in adverse conditions. It also protects the motor against any grid anomaly.
Its compact and book type design, a rear cooling system and its frontal connections enable the user to install easily multiple units in a compact cabinet.
ENERGY SAVINGThe variable speed drives reduce the energy consumption of the motor according to the demand of the system. They can save up to 70% of the energy consumption and reduce the maintenance task on your facility.
T máx.
T arranque
50%
1Hz 10Hz 40Hz 50Hz 60Hz
Velocidad (Hz)
Par(%)
BUILT-IN PID CONTROLThis function enables the control of a wide variety of system variables: flow, pressure, temperature, etc., without any additional external controller.
PRESSURETRANSDUCER
PID CONTROLSTHE SYSTEM
SYSTEM SET-POINT
Feedback signal
Controlloop
PUMP
05.
SD25
0 S
ER
IES
LOW VOLTAGE / POWER ELECTRONICS
38-39
INPUT
Power range 0,4kW - 22kW
Voltage power 200-230Vca, 380-480Vca (-15% a +10%) (trifásico)
Input frequency 50~60 Hz ±5%
EMC/RFI Filter Class 2
Harmonics filter Three phase and external dc optional
Input rectifier technology Diode
OUTPUT
Overload capacity 150% during 60 sec.
Frequency ratings 400Hz
Control Method V/Hz control, Vector control (Sensorless)
Efficiency >98%
Modulation method Vector space modulation
Modulation frequency Maximum 15kHz
Output cable length USC 50m, SC 25m [1]
Dynamic brake Built-in. Optional dynamic braking
ENVIRONMENTALCONDITIONS
Degree of protection IP20
Operation temperature -10°C to +50°C
Storage temperature -20°C to +70°C
Relative humidity <90%, non-condensing
Altitude 1000m
Power altitude derating (> 1000m) (>1000m)-1% per 100m; maximum 3000m
Vibration 5,9m/sec2 (=0,6G)
Ventilation Air forced refrigeration
PROTECTIONS
Motor thermal model Motor stall warning Low voltage
Phases current imbalance Over voltage Ground fault
Overload warning Dynamic brake resistor thermal model Torque limit and torque limit time (adjustable)
Short-circuit Mean torque 100% of braking during 5s. Communications fault
Overtemperature Stall motor protection Input/Output phase loss
COMMUNICATION
Standard Hardware RS485 port
Standard Protocol Modbus-RTU
Optional Hardware Profipower, Ethernet, N2 Metasys
Optional Protocols Profibus, Devicenet
INPUTS/OUTPUTS
Analogue inputs 1 input 0-10Vac ±10Vdc / 1 input 0-20mA or 4-20mA
Digital inputs 8 configurable inputs
Analogue outputs 1 output 0-10Vdc
Relay output 1 Changeover programmable relay (250Vac, 1A; 30Vdc, 1A) 1 Programmable open collector transistor output (26VDC, 100mA)
CONTROL Display Keypad and digital programming unit. Removable optional
REGULATIONS CE, cTick, UL[2], cUL[2]
WIRING CONTROL
Note: The MO output has been designed fora maximum current of 80mA.
MO MG 24 P1 P2 CM P3 P4 P5 CM P6 P7 P8 VR V1 I AM3A 3C 3B S+ S-
24VDC
Fact
ory
Set
ting
s
Mul
ti-F
unc. O
pen
Co
llect
or
Out
put
< 26
VD
C, 1
00
mA
24V
Out
put
Fo
rwar
d Run
(F
X)
Rev
erse
Run
(R
X)
Co
mm
on
Em
erg
ency
Sto
p (B
X)
Trip
Res
et (
RS
T)
Jog
Op
erat
ion
(JO
G)
Co
mm
on
Mul
ti-S
tep
Fre
q.-
Low
Mul
ti-S
tep
Fre
q.-
Mid
dle
Mul
ti-S
tep
Fre
q.-
Hig
h
10 P
ower
Sup
ply
for P
oten
tiom
eter
Vo
ltag
e S
igna
l Inp
ut 0
-10
V
Cur
rent
Sig
nal I
nput
0-2
0m
A
Mul
ti-F
unc.
Ana
log
ue
Out
put
0-1
0V
RS
48
5 C
om
mun
icat
ion
Term
inal
MF InputTerminals
1-2
MF InputTerminals
3-5
Multi-Func. Relay(< 250 Vac, 1A;
30VDC, 1A)
MF InputTerminals
6-8
80mAmax.
Technical CharacteristicsWiring control
NOTES [1] Other configurations, consult Power Electronics.[2] On process.
05.
SD25
0 S
ER
IES
TOPOLOGIES
13070 4.54
.5
4
65.5
128
119
65.54
140132
4.5
120
.5
128
4.5
4.5 4.5
155
4.5
170180
220
210
5
4.54.5170
170
7
235
219
304
320
2197
8
7
189.5
130
95.54.5
4.5100
120
4.5
128
95.5
4.5
10
208.5240260
392
24010
410
10
10
DIMENSIONS (mm) AND WEIGHTS (kg)
FRAME WEIGHT (kg)
1 0,76
FRAME WEIGHT (kg)
2 1,12
FRAME WEIGHT (kg)
3 1,87
FRAME WEIGHT (kg)
4 3,66
FRAME WEIGHT (kg)
5 9
FRAME WEIGHT (kg)
6 13
TopologiesDimensions and Weights
L1
L2
L3
R
S
T
UVW
P1(+)
PE
N(-)
RECTIFIER DC BUS INVERTER
Frames 5 and 6 can optionally integrate DC harmonic filters.
B
DYNAMIC BRAKE
Optionalharmonics
filter
OptionalRFI
filterOptional
dV/dt filter
LOW VOLTAGE / POWER ELECTRONICS
40-41
Standard ratingsAccessories
CONFIGURATION TABLE
STANDARD RATINGS
200Vac-230Vac (-15% a 10%)
FRAME CODE I(A) RatedPOWER
kW HP
1SD25203 3 0.4 0.5
SD25205 5 0.75 1
2 SD25208 8 1.5 2
3SD25212 12 2.2 3
SD25217 17 4 5.4
4SD25224 24 5.5 7.5
SD25232 32 7.5 10
5SD25246 46 11 15
SD25260 60 15 20
6SD25274 74 18.5 25
SD25288 88 22 30
380Vac-480Vac (-15% a 10%)
FRAME CODE I(A) RatedPOWER
kW HP
1SD25301 1.25 0.4 0.5
SD25302 2.5 0.75 1
2 SD25304 4 1.5 2
3SD25306 6 2.2 3
SD25309 9 4 5.4
4SD25312 12 5.5 7.5
SD25316 16 7.5 10
5SD25324 24 11 15
SD25330 30 15 20
6SD25339 39 18.5 25
SD25345 45 22 30
CODE CURRENT I (A)
LEAKAGE CURRENT I(mA)VOLTAGE
(V)
DIMENSIONS (mm)APPLICABLE DRIVES
Rated Maximum W D H
FESD25302 5 0.5 26250
76.5 40 175SD25203, SD25205
400 SD25301, SD25302
FESD25208 12 0.5 26 250 107,5 40 176.5 SD25208
FESD25304 6 0.5 26 400 107,5 40 176.5 SD25304
FESD25217 20 0.5 26 250 147,5 45 176.5 SD25212, SD25217
FESD25309 11 0.5 26 400 147,5 45 176.5 SD25306, SD25309
FESD25232 50 0.5 26 250 189,5 60 270 SD25224, SD25232
FESD25316 30 0.5 26 400 189,5 60 270 SD25312, SD25316
FESD25260 65 3.2 34 480 255 65 418 SD25246, SD25260
FESD25330 35 3.2 34 480 255 65 418 SD25324, SD25330
FESD25288 90 3.2 34 480 280 65 506 SD25274, SD25288
FESD25345 45 3.2 34 480 280 65 506 SD25339, SD25345
RFI FILTERS
INPUT
OUTPUT
H
WD
SD25 016 2
SD250 series Rated voltage Output current
SD25 2 200-230V 01 1,25A
3 380-480V ... ...
88 88A
ACCESSORIES
CODE ACCESSORIES DESCRIPTION
SD25TCD DeviceNet communication module
I001 Profibus
I002 Ethernet
SD25CF1 Display extender kit (5 meters)
[1] Verifiy the rated current of the motor nameplate to guarantee the compatibility with the selected drive.
LOW VOLTAGE / POWER ELECTRONICS
05.
SD25
0 S
ER
IES
CODE CURRENT I (A)
VOLTAGE (V)
DIMENSIONS (mm)APPLICABLE DRIVES
W D H
FHSD4004 4 400 170 120 230 SD25301, SD25302, SD25304
FHSD4008 8 400 170 120 230 SD25306
FHSD4016 16 400 170 120 230 SD25309, SD25312, SD25316
FHSD4024 24 400 140 100 320 SD25324
FHSD4030 30 400 140 100 320 SD25330
FHSD4045 45 400 230 100 320 SD25339, SD25345
INPUT HARMONICS FILTER
H
W D
H
W D
D W
30
H
MODEL 1(IP00)
MODEL 2(IP20)
MODEL CODE CURRENT I (A)
DIMENSIONS (mm)APPLICABLE DRIVES
W D H
1 (IP00)
FSDVDT-030 30 150 81 135
SD25203, SD25205, SD25208, SD25212
SD25217, SD25224, SD25232, SD25301
SD25302, SD25304, SD25306, SD25309
SD25312, SD25316, SD25324, SD25330
FSDVDT-050 50 180 85 160 SD25246, SD25339, SD25345
FSDVDT-070 70 180 85 160 SD25260
FSDVDT-100 100 180 185 175 SD25274, SD25288
2(IP23)
FSDVDT-030-23 30 240 210 265
SD25203, SD25205, SD25208, SD25212
SD25217, SD25224, SD25232, SD25301
SD25302, SD25304, SD25306, SD25309
SD25312, SD25316, SD25324, SD25330
FSDVDT-050-23 50 240 210 265 SD25246, SD25339, SD25345
FSDVDT-070-23 70 240 210 265 SD25260
FSDVDT-100-23 100 281 225 340 SD25274, SD25288
OUTPUT dV/dt FILTERS
NOTE Consult Power Electronics in case of additional requirements.