ut-sata-c-1 serialatapcicard 1 1 e
TRANSCRIPT
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
1/19
Serial ATA PCI Card
Users Manual
- ar .
erial ATA Cable X 2
ser anua s.
- ar r ver - .
PACKING
LIST
This package contains each of products listed above.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
2/19
ntroduction:
The perfect way to get all the performance and data protection of Serial ATARAID or Ser a ATA tec no ogy. T e UT-SATA_C PCI Car supportsSerial ATA Devices. For optimal performance, install identical drives of the same
model and capacity when creating RAID sets.
T e UT-SATA_C PCI Car nc u es t e s con mage S 3112A contro er
chipset and two Serial ATA interfaces to supports Redundant Array of
Independent Disks (RAID) conguration. This feature supports Serial ATA hard
disks. Use the SATARaid utility to congure the RAID sets.
Features:
General
Serial ATA 150MB/s
Compliant with Serial ATA 1.0 specication
Integrate Ser a ATA Transport, L n og c an PHY
48-bit sector addressing
ual independent DMA channels with 256B FIFO per channelVirtual DMA
egister compatible with parallel ATA
river support for Windows 98, 98SE, ME, Windows 2000, Windows
Supports RAID 0 (Striping) and RAID 1 (Mirroring)
S con Image Supp es t e S -3112A c pset, support ng t e u tra-
compact 7-pin
Serial-ATA IDE device support.
PCI Bus
Compliant with 32 bit, 33/66 MHz PCI slot
PCI 2.2 Compliant
Power
5V operating voltage PCI bus
ACPI: PCI Bus Power Management Spec 1.1 Compliant
1
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
3/19
System Requirements:
Use w t IBM PC compat e
Windows 98, 98SE, ME, Windows 2000/ NT4.0 and Windows XP
One 33/66 MHz PCI expansion slot.
X CD-ROM
Floppy Diver
WARNING:
Unp ug your power supp y w en a ng or remov ng expans on
cards or others system components.
Failure to do so many causes you physical injury and damage
motherboard components.
nstalling the Serial ATA PCI Card:
Follow these steps to install the UT-SATA C card
1. Before installing the Serial ATA PCI Card read the document that came with
t an ma e t e necessary ar ware sett ngs.
2. Discharge any electricity from your body by touching a grounded metal
object (such as the exposed metal parts on the back of your computer).
3. Turn the power off on your computer and disconnect the power cord.
4. Open t e computer case. See your computer ocumentat on or spec c
instructions, if needed.
5. Secure the card to the chassis with screw you removed earlier.
6. Select an unused 32-bit or 64-bit PCI slot. Remove the expansion slot cover.
2
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
4/193
7. A gn t e car to connector w t t e s ot an
Replace the slot cover screw.
8. Press rmly until the card is completely seated on
t e s ot. An c ose t e computer case.
9. Replace the system cover.
10. Set up the BIOS if necessary and restart
computer.
11. D rect nsta so tware ut ty to mon tor an
manipulate Silicon Image Serial ATA.
First time installation with WindowsNT4.0or Windows2000/XP:
Fo ow t e nstruct ons n t s sect on you are per orm ng a new nsta at on
of Windows NT 4.0 or Windows 2000/XP, and you wish to boot from a device
attached to the SiI 3112 SATARaid controller.
First you must copy Driver CD: \ oppy disk\*.* to Floppy disk, make a
Silicon Image SiI 3112 SATARaid Controller Installation Disk.
1. Put your Windows NT 4.0 or Windows 2000/XP CD into the CD/DVD-ROM
drive or the Win 2000 boot diskette #1 in the oppy drive if your system
cannot boot from the CD-ROM.
wo ports n para e at ac s e o car
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
5/194
2. Press [F6] or t r party SCSI or
driver installation at the beginning of
text mode installation.
3. Press S From the list that appears.
4. P ease nsert t e Silicon Image SiI
3112 SATARaid Controller
Installation Disk Into Drive A: andpress Enter o continue with
nsta at on.
5. Windows XP users please choose
Silicon Image SiI 3112 SATARaidController for Windows XP From
the list that appears on screen and then
press Enter
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
6/195
6. I you are setup w t W n ows
NT4.0/2000 users please choose
Silicon Image Sil 3x12 SATARaid
controller for Windows NT 4.0 and
2000 From t e st t at appears onscreen and then press Enter.
7. Press Enter again when prompted
to continue on with text mode setup.
T e W n ows NT 4.0 or W n ows
2000/XP Setup screen will appear againSetup will load support for the following
mass storage devicesSilicon Image
SiI 3112 SATARaid Controller
NOTE
If there are any additional devices to be installed, specify them now.
When all devices are specied, continue to the next step.
8. Follow the setup instructions to select
your choice for partition and le
system. Press Enter to Insta .
9. The Windows NT 4.0 or Windows 2000/XP Setup screen, press the Enter
Setup will now load all device les and then continue the Windows2000/XP
installing.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
7/19
Update Driver an Existing Windows2000 / XP
Installation:
Follow the instructions in this section to install the Silicon ImageSiI 3112
driver on a system already running Windows 2000/XP.
1. Power off the system. Connect the hard drives to the SiI 3112 controller and
insert the controller into a PCI slot. Power ON the system.
2. Insert the Driver CD into the CD-ROM.
3. Right click on My Computer icon,
se ect Properties, e t c c onHardware tab, and then on Device
Managerbutton. Double click on
SCSI and RAID Controllers,
t ere s no ye ow! or ? n ront
ofSilicon Image SiI 3112 SATA
Controller, the driver has started
correct y.
4. During OS boot up, Windows willdisplay the Found New Hardware
Wizard ClickNext. elect
Search for a suitable driver for my
device (Recommended)and Click
Next.
5. Un er Opt ona searc ocat ons
insure that Floppy disk drives is
checked; insert the Driver CD into
CD-ROM: and clickNext
6
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
8/197
6. I t e Digital Signature Not Found
dialog appears, clickContinue
Anyway installing the driver.
7. The wizard will now install the
so tware to t e system r ver.
8. The wizard will display a completion
dialog, clickFinish o exit the
w zar .
9. Right click on My Computer icon,
select Properties, left click on
Hardware tab, and then on Device
Manager utton. Dou e c c on
SCSI and RAID Controllers, The
Silicon Image SiI 3112 SATA
Controller setup correctly.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
9/19
First Time Fresh Installation with Windows98SE / ME:
Fo ow t e nstruct ons n t s sect on you are per orm ng a new nsta at on
of Windows 98SE/ME and you wish to boot from a device attached to the SiI
3112 controller.
First You Must Copy the Silicon Image SiI 3112 SATARaid Controller
Installation Disk Driver\3112Raid_10027\si3112r.inf from CD to Floppy.
1. Power off the system. Insert the SiI 3112 controller into an available PCI
s ot. Connect ser a ATA ca e s etween t e S I 3112 contro er an t e
serial ATA device(s). Power up the system.
2. Put your W n ows 98SE ME CD nto t e CD-ROM DVD r ve, an t e
Windows 98SE/ME boot diskette in the oppy drive if your system cannot
boot from the CD.
3. Fo ow t e norma W n ows 98SE ME setup nstruct ons to se ect your
choice for partition and le system.
4. Wait until Windows 98SE/ME nishes installing devices, regional settings,
networking settings, components, and nal set of tasks, reboot the system.
5. After the system reboots, right click
My Computer an se ect
Properties'. From system
Properties select Device Manager
, right click on the ? PCI Mass
Storage controller an se ect
Properties from the context menu.
8
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
10/199
6. C c Driver, Update Driver
and select Automatic search for a
better driver [Recommended].
7. Insert the diskette labeled Silicon
Image SiI 3112 SATALink Driver
Insta at on D s nto oppy r ve.
ClickNext and complete the driverinstallation.
8. System w go t roug t e
enumeration process and install the
driver. At the end of the process,clickFinish to reboot your system.
Update Driver an Existing Windows 98SE/MEnstallation:
1. Power off the system. Connect the hard drives to the SiI 3112 SATARaid
contro er an nsert t e contro er nto a PCI s ot, Power on t e system.
During the system boot up, the Hardware Wizard will display that it found a
PCI RAID Controller, clickNext.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
11/19
2. Select Search for the best driver
for your device [Recommended]
an c c Next.
3. Check the Floppy disk drives
and insert the driver diskette into
oppy r ve. C c Next.
4. System w go t roug t e
enumeration process and install thedriver. At the end of the process,
ClickFinish to complete the
nsta at on. Re oot t e system your
Windows 98SE/ME drive is connected
on the SiI 3112SATARaid Controller.
10
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
12/19
RAID 0 & RAID 1 Con gurations :
The Sil 3112A chipset supports Serial ATA hard disk drives. For optimal
per ormance, nsta ent ca r ves o t e same mo e an capac ty w en
creating RAID sets.
What is RAID 0 & RAID 1?
If you are creating a RAID 0(striping) array for performance, use two new
drives.
I you are creat ng a RAID1 m rror ng array or protect on, you can use
two new drives or use an existing drive and a new drives (the new drivesmust be of the same size or larger than the existing drive).
If you use two drives with different sizes, the smaller capacity hard disk
will be the base storage size. For example, hard disk A with an 80GB
storage capacity and hard disk B with 60GB storage capacity for your
RAID1 set w e 60 GB.
Follow these steps to install the hard disks for RAID conguration.
1. Install the Serial ATA hard disk into the drive bays.
2. Connect one Ser a ATA HDD to eac Ser a ATA connector, us ng separate
serial ATA cables.
3. Connect the power cable to the power connector on each drive.
4. Proceed to Creating and Deleting Raid sets for the next procedure.
11
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
13/19
reating & Deleting RAID Sets:
Creating and deleting RAID sets is a built-in function found in the BIOS.
The following sub-sections describe how to use the RAID Conguration Utility.
Loading the RAID Conguration Utility
1. During POST, press CTRL
[F4] to enter RAID Con gurat on
Utility. The following menu optionswill appear.
2. Select Create RAID Set
12
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
14/19
3. C oose e t er a Striped
Mirrored RAID Set.
4. Select if you want the utility to
Auto Congure the RAID set.
13
rrore
Striped (RAID 0)
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
15/19
5. T e ut ty w as Are You Sure
(Y/N)before completing the
conguration. Press [Y] to conrm or
[N] to go back to the conguration
opt ons.
6. If you want to manually congure theRAID set. For Striped Sets, you can
change the chunk size. For Mirrored
Sets, you ass gn w c s t e Source
and Target drives, as well as if you want
a Disk Copy.
14
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
16/1915
What is a chunk? The chunk size is the stripe on each disk. It is the
unit of storage equivalent to one strip on a RAID 0 set. Available chunk
sizes:
248163264128
When manually setting the chunk size for your RAID, it is recommended
to use the smaller chunk size for server applications and the larger chunk
size for AV applications.
W at s D s Copy? I t e s ass gne as t e source s as een
partitioned and has data stored on it, and a second disk is added, the dataon the source Drive can be copied to the destination drive so the disks
are identical, and all subsequent data will be written to both drives as a
M rrore set. I , owever, t e source s oes not ave ata store on t,
there is no need for Disk Copy.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
17/1916
7. T e ut ty w as Are You Sure
(Y/N) ?before completing the
conguration. Press [Y] to conrm
or[N] to go back to the conguration
opt ons.
Deleting RAID Sets
1. To remove one or more RAID sets,select Delete RAID Set and
Set (Number)
2. Se ect es re set an press [Y] w en
asked Are You Sure Y/N.
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
18/1917
Resolving Conict
When a RAID set is created the metadata written to the disk includes drive
connect on n ormat on Pr mary C anne , Secon ary C anne . I a ter a sfailure, the replacement disk was previously part of a RAID set (or used in
another system), it may have conicting metadata, specically in reference to
the drive connection information if so, and this will prohibit the RAID set from
being either created or rebuilt. In order for the RAID set to function properly,
this old metadata must be rst overwritten with the new metadata, including the
correct drive connection information, will be written to the replacement disk.
1. Select the esolving conicts
2. Se ect t e De ete RAID SET an
Chose Set 0
-
7/31/2019 Ut-sata-c-1 Serialatapcicard 1 1 e
19/19
Speci cation:
Interface Serial ATA /150 port X 2
Stan ar s RAID Leve s RAID 1 m rror ng
Compliance Data Transfer Rate Up to 266MB/sec (66MHz PCI)
RAID Levels RAID 0 striping
Data Transfer Rate Up to 133MB/sec (33MHz PCI)
D mens on 124.5mm L x 62.9mm W x 10.7mm H
Weight 51 gram
Data transfer rates may depending on drive make motherboard and PCI bus speed.
acking List:
T-SATA PCI Car .
erial ATA Cable X 2
ser Manuals.
T-SATA PCI Card Driver CD-ROM.