user manual idk-1110wr-50wsa1advdownload.advantech.com/productfile/downloadfile2/1-1v...idk-1110wr...

35
User Manual IDK-1110WR-50WSA1 101" WSVGA Industrial Display Kit with 4-Wire Resistive Touch Solution

Upload: others

Post on 19-Feb-2021

1 views

Category:

Documents


0 download

TRANSCRIPT

  • User Manual

    IDK-1110WR-50WSA1

    101" WSVGA IndustrialDisplay Kit with 4-Wire Resistive Touch Solution

  • IDK-1110WR User Manual ii

    CopyrightThe documentation and the software included with this product are copyrighted 2019by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the rightto make improvements in the products described in this manual at any time withoutnotice. No part of this manual may be reproduced, copied, translated or transmittedin any form or by any means without the prior written permission of Advantech Co.,Ltd. Information provided in this manual is intended to be accurate and reliable. How-ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-ments of the rights of third parties, which may result from its use.

    AcknowledgementsAMI is a trademark of American Megatrends IncIBM and PC are trademarks of International Business Machines CorporationIntel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corpo-rationWinBond is a trademark of Winbond CorporationAll other product names or trademarks are properties of their respective owners

    Part No. 2006111022 Edition 3Printed in Taiwan November 2019

  • iii IDK-1110WR User Manual

    A Message to the CustomerAdvantech Customer Services

    Each and every Advantech product is built to the most exacting specifications toensure reliable performance in the harsh and demanding conditions typical of indus-trial environments. Whether your new Advantech equipment is destined for the labo-ratory or the factory floor, you can be assured that your product will provide thereliability and ease of operation for which the name Advantech has come to beknown. Your satisfaction is our primary concern. Here is a guide to Advantech’s cus-tomer services. To ensure you get the full benefit of our services, please follow theinstructions below carefully.

    Technical Support

    We want you to get the maximum performance from your products. So if you run intotechnical difficulties, we are here to help. For the most frequently asked questions,you can easily find answers in your product documentation. These answers are nor-mally a lot more detailed than the ones we can give over the phone.So please consult this manual first. If you still cannot find the answer, gather all theinformation or questions that apply to your problem, and with the product close athand, call your dealer. Our dealers are well trained and ready to give you the supportyou need to get the most from your Advantech products. In fact, most problemsreported are minor and are able to be easily solved over the phone.In addition, free technical support is available from Advantech engineers every busi-ness day. We are always ready to give advice on application requirements or specificinformation on the installation and operation of any of our products.

  • IDK-1110WR User Manual iv

    Product Warranty (2 years)Advantech warrants to you, the original purchaser, that each of its products will befree from defects in materials and workmanship for two years from the date of pur-chase. This warranty does not apply to any products which have been repaired or altered bypersons other than repair personnel authorized by Advantech, or which have beensubject to misuse, abuse, accident or improper installation. Advantech assumes noliability under the terms of this warranty as a consequence of such events.Because of Advantech’s high quality-control standards and rigorous testing, most ofour customers never need to use our repair service. If an Advantech product is defec-tive, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials,service time and freight. Please consult your dealer for more details.If you think you have a defective product, follow these steps:1. Collect all the information about the problem encountered. (For example, CPU

    speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.

    2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.

    3. If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly.

    4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.

    5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

  • 1 IDK-1110WR User Manual

    ContentsChapter 1 Overview...............................................1

    1.1 General Description .................................................................................. 21.2 Display Characteristics.............................................................................. 21.3 Display Optical Characteristics ................................................................. 3

    1.3.1 Measuring Condition ..................................................................... 31.3.2 Measuring Equipment ................................................................... 3

    1.4 Block Diagram........................................................................................... 5Figure 1.1 TFT LCD Module ........................................................ 5

    1.5 Absolute Maximum Ratings ...................................................................... 51.5.1 Absolute Max Rating..................................................................... 5

    1.6 Dimensions ............................................................................................... 61.6.1 Front View..................................................................................... 61.6.2 Rear View ..................................................................................... 6

    Chapter 2 Electrical Characteristics...................72.1 TFT LCD Module....................................................................................... 8

    2.1.1 Power Specifications..................................................................... 82.1.2 LVDS DC Electrical Characteristics .............................................. 82.1.3 LVDS AC Electrical Characteristics .............................................. 9

    2.2 Backlight Unit .......................................................................................... 102.2.1 Parameter Guidelines for LED Backlight .................................... 10

    Chapter 3 Signal Characteristics.......................113.1 Electrical Interface Connection ............................................................... 12

    Table 3.1: Connector ................................................................. 133.2 The Input Data Format ............................................................................ 133.3 Interface Timing ...................................................................................... 14

    3.3.1 Timing Characteristics ................................................................ 14Table 3.2: Timing Characteristics .............................................. 14

    3.3.2 Input Timing Diagram.................................................................. 143.4 Power ON/OFF Sequence ...................................................................... 15

    Chapter 4 Touch Screen.....................................174.1 Touch Characteristics ............................................................................. 18

    Chapter 5 Touch Controller................................195.1 Touch Controller Characteristics............................................................. 205.2 Specifications .......................................................................................... 205.3 Environmental Features .......................................................................... 205.4 Pin Assignments and Description ........................................................... 21

    5.4.1 Connector and LED Location...................................................... 215.4.2 Combo Interface Connector, JP1, Pins and Signal Descriptions 21

    Figure 5.1 Board Mounted Header ............................................ 215.4.3 Touch Screen Connector, JP2, Pins and Signal Descriptions .... 21

    Appendix A LCD EDID............................................23

  • IDK-1110WR User Manual 2

    A.1 LCD EDID ............................................................................................... 24

  • Chapter 11 Overview

  • IDK-1110WR User Manual 2

    1.1 General DescriptionThis specification applies to the 10.1 inch color TFT LCD module IDK-1110WR-50WSA1. IDK-1110WR-50WSA1 is designed with a wide viewing angle, wide operat-ing temperature range, and along lifespan for the LEDs backlight; making it wellsuited as a display unit for Industrial Applications. An LED driving board for the back-light unit is included in this panel. IDK-1110WR-50WSA1 uses a built in timing con-troller and LVDS interface. The screen format is intended to support the WSVGA(1024(H) x 600(V)) screen and 262k colors (RGB 6-bits). IDK-1110WR-50WSA1 is aRoSH product.

    1.2 Display CharacteristicsThe following characteristics are summarized on the table below for under 25°C con-ditions.

    Items Specifications UnitScreen Diagonal 10.1 (Diagonal) inchActive Area 222.72(H) x 125.28(V) mmPixels H x V 1024 x 3(RGB) x 600Pixel Pitch 0.2715 x 0.2088 mmPixel Arrangement R.G.B. Vertical StripeDisplay Mode TN, Normally WhiteNominal Input Voltage VDD 3.3 typ VoltTypical Power Consumption 3.834 typ. WattWeight 180 ± 10 GramsPhysical Size 235.0(W) x 143 (H) x 4.9 (D) (typ.) mmElectrical Interface 1 channel LVDSSurface Treatment Anti-glare, Hardness 3HSupport Color 262K(6-bit) / 16.7M (8-bit)Temperature RangeOperating Storage (Non-Operating)

    -5 to + 60-20 to +70

    °C°C

    RoHS Compliance RoHS Compliance

  • 3 IDK-1110WR User Manual

    Chapter 1

    Overview

    1.3 Display Optical CharacteristicsThe optical characteristics are measured under stable conditions at 25°C (RoomTemperature):

    1.3.1 Measuring Condition Measuring surrounding: dark room Ambient temperature: 25±2° 15 min. warm-up time

    1.3.2 Measuring EquipmentThe optical characteristics are measured in a dark room. After 30 minutes operation,the optical properties are measured at the center point of the LCD screen. (Responsetime is measured by a Photo detector TOPCON BM-7 of view: 1° / Height: 120 mm.)

    Note1: Definition of viewing angle range

    Item Symbol ConditionsValues Unit Note

    Min. Typ. Max.Viewing Angle L (CR 10) 60 70 -- degree 1, 2

    R 60 70 --U 50 60 --D 50 60 --

    Response Time TR+TF - 20 35 msec 3Contrast Ratio CR 400 500 -- - 2Color Chromaticity WX 0.263 0.313 0.363 - 1, 4

    WY 0.279 0.329 0.379 -RX 0.512 0.562 0.612 -RY 0.281 0.331 0.381 -GX 0.279 0.329 0.379 -GY 0.522 0.572 0.622 -BX 0.11 0.160 0.210 -BY 0.084 0.134 0.184 -

    Luminance L 400 500 -- cd/m2 4

    Luminance Uniformity YU 80 -- -- % 5

  • IDK-1110WR User Manual 4

    Note 2: Definition of Contrast Ratio Contrast ratio is calculated with the following formula : Contrast Ratio (CR)=(White) Luminance of ON ÷ (Black) Luminance of OFFNote 3: Definition of Response time: Sum of TR and T

    Note 4: Definition of optical measurement setup

    Note 5: Definition of brightness uniformity

    (Min Luminance of 5 points) Luminance uniformity =------------------------------------------------×100% (Max Luminance of 5 points)Note 6: Rubbing Direction (The different Rubbing Direction will cause the differentoptimal view directionNote 7: Condition: Ta=25°C, Life time is estimated data.

  • 5 IDK-1110WR User Manual

    Chapter 1

    Overview

    Definitions of failure:1. LCM brightness becomes half of the minimum value. 2. LED doesn’t light normally.

    1.4 Block Diagram

    Figure 1.1 TFT LCD Module

    1.5 Absolute Maximum Ratings

    1.5.1 Absolute Max Rating

    Note: Maximum Wet-Bulb should be 39°C and no condensation.

    Item SymbolValue

    Unit NoteMin. Max.Logic/LCD Drive Voltage VCCS -0.3 4.0 VEDID Drive Voltage VEDID -0.3 4.0 VConverter Input Voltage LED_VCCS -0.3 23 VConverter Control Signal PWM Voltage LED_PWM -0.3 6.0 VConverter ControlSignal Enable Voltage LED_EN -0.3 6.0 V

    Operating Temperature TOPA -5 60 °CStorage Temperature TSTG -20 70 °C

  • IDK-1110WR User Manual 6

    1.6 Dimensions

    1.6.1 Front View

    1.6.2 Rear View

    Note: Tolerances unless marked are ±0.5mm

  • Chapter 22 Electrical Characteristics

  • IDK-1110WR User Manual 8

    2.1 TFT LCD Module

    2.1.1 Power SpecificationsInput power is shown as follows:

    Note: Measurement condition:

    2.1.2 LVDS DC Electrical CharacteristicsInput signals should be low or Hi-Z states when VCCS is off.

    Note: LVDS Signal Waveform.

    Item SymbolValue

    Unit NoteMin. Typ. Max.Logic/ LCD Driver Voltage VCCS 3.0 3.3 3.6 V

    VCCS Current IVCCS - 0.14 0.16 AVDD=3.3V, at 60HzBlack Pattern

    LCD Inrush Current Iruch - - 1.5 A 1

    VCC Power PVCCS - 0.46 0.53 WattVCCS=3.3V, at 60HZBalck Pattern

    Allowable Logic/LCD Drive Ripple Voltage VCCSrp - - 150 mV p-p

    Parameter SymbolValue

    Unit RemarkMin. Typ. Max.Differential Input High Threshold

    VTH - - 100 mV

    Differential InputLow Threshold

    VTL -100 - - mV

    Differential Input Voltage VID 100 - 600 mVCommon Mode Voltage Offset VICM 1.125 - 1.375 VLVDS Terminal Resistor ICRTC - 100 - Ohm

  • 9 IDK-1110WR User Manual

    Chapter 2

    Electrical C

    haracteristics

    2.1.3 LVDS AC Electrical Characteristics

    Item Symbol Min. Typ. Max. Unit RemarkDifferential Pulse Skew tSKD 0.5 nsTransition Low to High Time

    tTLH 1 ns

    Transition High to Low to Time

    tTHL 1 Ns

    Offset Voltage Imbal-ance

    VOS 200 mV

  • IDK-1110WR User Manual 10

    2.2 Backlight Unit

    2.2.1 Parameter Guidelines for LED Backlight The following characteristics are measured under a stable condition using an inverterat 25°C (Room Temperature):

    Note1: Condition: Ta=25°C, continuous lightingLife time is estimated data. Definitions of failure: 1. LCM brightness becomes half of the minimum value. 2. LED doesn’t light normally.

    Parameter SymbolValue

    Unit NoteMin. Typ. Max.LED Driver Voltage LED_VCCS 9 12 15 V

    Input Current ILED - 225 270 mA VLED=12V (duty 100%)Power Consumption PLED - 2.7 3.3 W

    LED_EN VoltageBL On 2.3 - 5 VBL Off 0 - 0.5 V

    PWM Frequency FPWM 190 2000 HzPWM Duty Ratio DPWM 10 - 100 %

    PWM Control LevelHigh Level 2.3 - 5

    VLow Level 0 - 0.5

    LED Life Time 50,000 Hour

  • Chapter 33 Signal Characteristics

  • IDK-1110WR User Manual 12

    3.1 Electrical Interface Connection

    Note: Inpout Signals shall be in low status when VCCS is off

    Pin No. Symbol Description Note1 NC No connection2 VCCS 3.3V Power3 VCCS 3.3V Power

    4 V_EDID 3.3V Power for EDID, if EDID function is not used, please keep it floating.5 NC No connection, 100K pull-down resistance in LCM6 CLK_EDID EDID Clock Input, if EDID function is not used, please keep it floating.7 DATA_EDID EDID Data Input, if EDID function is not used, please keep it floating.8 RXIN0- LVDS Signal - channel0-9 RXIN0+ LVDS Signal+ channel0+10 GND Ground11 RXIN1- Data Input channel1-12 RXIN1+ Data Input channel1+13 GND Ground14 RXIN2- Data Input channel2-15 RXIN2+ Data Input channel2+16 GND Ground17 RXCLKIN- Data Input CLK-18 RXCLKIN+ Data Input CLK+19 GND Ground20 RXIN3- Data Input channel 321 RXIN3+ pin 20 & pin 21 connect to GND or NC for 6bit LVDS input22 GND Ground23 NC No connection24 NC No connection25 GND Ground

    26 Order_SEL LVDS format selection.Order_SEL="H": JEIDA/Order_SEL="L" or NC: NS-Like

    27 SEL68 6/8 bits LVDS data input selectionSEL68="H": 8bits/ SEL68="L" or NC: 6bit28 GND Ground29 NC No connection30 NC No connection31 LED_GND LED Ground32 LED_GND LED Ground33 LED GND LED Ground34 NC No connection35 LED_PWM PWM Control Signal of LED Converter36 LED_EN Enable Control Signal of LED Converter37 NC No connection38 LED_VCCS LED Power 12V39 LED_VCCS LED Power 12V40 LED_VCCS LED Power 12V

  • 13 IDK-1110WR User Manual

    Chapter 3

    Signal C

    haracteristics

    3.2 The Input Data Format

    Note: Output signals from any system shall be low to Hi-Z state when VCCS is off.

    Table 3.1: ConnectorManufacture IPEX or compatibleConnector Model Number IPEC 20455-040E-12R or compatibleAdaptable Plug IPEC 20453-040T-01 or compatible

  • IDK-1110WR User Manual 14

    3.3 Interface Timing

    3.3.1 Timing CharacteristicsDE mode only

    Note: DE Mode

    3.3.2 Input Timing Diagram

    Table 3.2: Timing Characteristics

    Item Symbol Min. Typ. Max. UnitClock Frequency Tdclk 40.8 51.2 67.2 MHz

    HorizontalSection

    Period TV 1114 1344 1400TdlckActive TVD 1024 1024 1024

    Blanking TVB 90 320 376

    VerticalSection

    Period TH 610 635 800

    TLineActive THD 600 600 600

    Blanking THB 10 35 200Frame rate F 50 60 70 Hz

  • 15 IDK-1110WR User Manual

    Chapter 3

    Signal C

    haracteristics

    3.4 Power ON/OFF Sequence

    Power ON/OFF Sequence Timing

    Note1 The above on/off sequence should be applied to avoid abnormal function inthe display. Please make sure to turn off the power when you plug the cable into theconnector or pull the cable out of the connector.

    Item Min. Typ. Max. UnitT1 0.5 - 10 msecT2 0 - 50 msecT3 200 - - msecT4 200 - - msecT5 0 - 50 msecT6 0 - 10 msecT7 500 - - msecT8 10 - - msecT9 10 - - msecT10 10 - - msecT11 10 - - msecT12 0.5 - 10 msec

  • IDK-1110WR User Manual 16

  • Chapter 44 Touch Screen

  • IDK-1110WR User Manual 18

    4.1 Touch CharacteristicsElectronic Characteristics

    Item Specification Remarks1 Rated Voltage DC 7V max.

    2 ResistanceX axis: 250 ~ 1200(FILM)

    FPC at connectorY axis: 100 ~ 600(GLASS)

    3 Chattering 10ms MaxAt connector pin

    4 Insulation Resistance 25M min (DC 25V)

  • Chapter 55 Touch Controller

  • IDK-1110WR User Manual 20

    5.1 Touch Controller CharacteristicsAdvantech ETM-RES05C Touch Control Board is the ultimate combo board. Thetouch panel controller provides analog resistive touch panels for 4 wire models. Itcommunicates with a PC system directly through USB and RS-232 connectors. Thetouch panel driver emulates mouse left and right button functions.

    5.2 SpecificationsElectrical Features +5 Vdc/ 100 mA typical, 50mV peak to peak maximum ripple and noise Bi-directional RS-232 serial communication and USB 1.1 full speed Report rate of RS-232 is 180 points/sec (max.). And, USB is 200 points/sec

    (max.) Unaffected by environmental EMI Panel resistance of 4-wire resistive model is from 50 to 200 ohm (Pin to pin on

    same layer) Touch resistance under 3K ohm

    Serial Interface EIA 232E (Serial RS-232) No parity, 8 data bits, 1 stop bit, 9600 baud (N, 8, 1, 9600) Support Windows 2000/ Vista/ XP/ 7, Windows CE 5.0/ 6.0/ 7.0, Windows NT4,

    Linux, DOS, QNX

    USB Interface Conforms to USB Revision 1.1 full speed. If the USB is connected to the controller, the controller will communicate over

    the USB, and will not communicate over the serial port. Support Windows 2000/ Vista/ XP/ 7, Windows CE 5.0/ 6.0/ 7.0, Linux, QNX

    Touch Resolution 2,048 x 2,048 resolution

    Response Time Max. 20 ms

    5.3 Environmental FeaturesReliability MTBF is 200,000 hours

    Temperature Ranges Operating: -25°C ~ 85°C Storage: -25°C ~ 85°C

    Relative Humidity

  • 21 IDK-1110WR User Manual

    Chapter 5

    Touch Controller

    95% at 60°C, RH Non-condensing

    Acquired RoHS certificateRegulatory FCC-B, CE approvalsDimension: 75 mm x 20 mm x 10 mm

    5.4 Pin Assignments and Description5.4.1 Connector and LED Location

    5.4.2 Combo Interface Connector, JP1, Pins and SignalDescriptionsThe combo interface connector, USB and RS-232, is a box 2.0mm 10-pins 90degree, Male type with lock connector, intended to be used with single wired pins in5+5 pins header. The pins are numbered as shown in the table below.

    Figure 5.1 Board Mounted Header

    5.4.3 Touch Screen Connector, JP2, Pins and Signal DescriptionsThe Touch Screen connector, JP2, is a FFC/FPC SMD 1.0mm 4-pins 90 degree,Female type connector. The pins are numbered as shown in the table below.

    LED

    JP1 Connector(USB&RS-232 Combo Interface)

    JP2 Connector(4-wire Touch screen interface)

    USB Pin#

    Signal Name

    Signal Function RS-232 Pin#

    Signal Name

    Signal Function

    1 G Ground 1 G Ground2 V USB Power 2 V Power3 G Ground 3 G Ground4 D+ USB D+ 4 TxD Serial Port5 D- USB D- 5 RxD Serial Port

  • IDK-1110WR User Manual 22

    TS4 Pin # Signal Name Signal Description1 YB Bottom2 XL Left3 YT Top4 XR Right

    4-Wire Touch Screen ZIF connector 4-Wire Screen viewed from cover sheet side

  • Appendix AA LCD EDID

  • IDK-1110WR User Manual 24

    A.1 LCD EDID

    Address Function Value Value Value NoteHEX HEX BIN DEC00 Header 00 00000000 001 FF 11111111 25502 FF 11111111 25503 FF 11111111 25504 FF 11111111 25505 FF 11111111 25506 FF 11111111 25507 00 00000000 008 EISA Manuf. Code LSB 06 00000110 609 Compressed ASCII AF 10101111 1750A Product Code D2 11010010 2100B hex. LSB first 10 00010000 160C 32-bit ser # 00 00000000 00D 00 00000000 00E 00 00000000 00F 00 00000000 010 Week of manufacture 30 00110000 4811 Year of manufacture 17 00010111 2312 EDID Structure Ver. 01 00000001 113 EDID revision # 00 00000000 014 Vedio input def. (digital I/P,

    non-TMDS, CRGB)80 10000000 128

    15 Max H image size (rounded to cm)

    16 00010110 22

    16 Max V image size (rounded to cm)

    0D 00001101 13

    17 Display Gamma(=(gamma*100)-100)

    78 01111000 120

    18 Feature support (no DFMS, Active OFF, RGB, tmg Blk#1)

    0A 00001010 10

    19 Red/green low bits (Lower 2:2:2:2 bits)

    15 00010101 21

    1A Blue/white low bits (Lower 2:2:2:2 bits)

    85 10000101 133

    1B RED x (Upper 8 bits) 97 10010111 151

    1C Red y/ high ER 8bits 58 01011000 881D Green x 53 01010011 831E Green y 8A 10001010 1381F Blue x 26 00100110 3820 Blue y 25 00100101 3721 White x 50 01010000 8022 White y 54 01010100 8423 Established timing 1 00 00000000 024 Established timing 2 00 00000000 025 Established timing 3 00 00000000 026 Standard timing #1 01 00000001 1

  • 25 IDK-1110WR User Manual

    Appendix A

    LCD

    ED

    ID

    Address Function Value Value Value Note27 01 00000001 128 Standard timing #2 01 00000001 129 01 00000001 12A Standard timing #3 01 00000001 12B 01 00000001 12C Standard timing #4 01 00000001 12D 01 00000001 12E Standard timing #5 01 00000001 12F 01 00000001 130 Standard timing #6 01 00000001 131 01 00000001 132 Standard timing #7 01 00000001 133 01 00000001 134 Standard timing #8 01 00000001 135 01 00000001 136 Pixel Clock/10000 LSB 2D 00101101 45

    37 Pixel Clock/10000 USB 11 00010001 17

    38 Horz active Lower 8bits 00 00000000 0

    39 Horz blanking Lower 8bits A0 10100000 160

    3A HorzAct: HorzBlnk Upper: 4:4 bits

    40 01000000 64

    3B Vertical Active Lower 8bits 58 01011000 88

    3C Vertical Blanking Lower 8bits

    13 00010011 19

    3D Vert Act: Vertical Blanking (upper 4:4 bit)

    20 00100000 32

    3E HorzSync: Offset 32 00110010 50

    3F HorzSync: Width 20 00100000 32

    40 VertSync. Offset: VertSynce. Width

    26 00100110 38

    41 Horz&Vert Sync Offset/Width Upper 2bits

    00 00000000 0

    42 Horizontal Image Size Lower 8bits

    DE 11011110 222

    43 Vertical Image Size Lower 8bits

    7D 01111101 125

    44 Horizontal & Vertical Image Size (upper 4:4 bits)

    00 00000000 0

    45 Horizontal Border (zero for internal LCD)

    00 00000000 0

    46 Vertical Border (zero for internal LCD)

    00 00000000 0

    47 Signal (non-intr, norm, no stero, sep sync. neg pol)

    18 00011000 24

    48 Detailed timing/monitor 00 00000000 049 descriptor #2 00 00000000 04A 00 00000000 04B 0F 00001111 154C 00 00000000 04D 00 00000000 0

  • IDK-1110WR User Manual 26

    Address Function Value Value Value Note4E 00 00000000 04F 00 00000000 050 00 00000000 051 00 00000000 052 00 00000000 053 00 00000000 054 00 00000000 055 00 00000000 056 00 00000000 057 00 00000000 058 00 00000000 059 20 00100000 325A Detailed timing/monitor 00 00000000 05B descriptor #3 00 00000000 05C 00 00000000 05D FE 11111110 2545E 00 00000000 05F Manufacture 41 01000001 65 A60 Manufacture 55 01010101 85 U61 Manufacture 4F 01001111 79 O62 0A 00001010 1063 20 00100000 3264 20 00100000 3265 20 00100000 3266 20 00100000 3267 20 00100000 3268 20 00100000 3269 20 00100000 3257 00 00000000 06A 20 00100000 326B 20 00100000 326C Detailed timing/monitor 00 00000000 06D descriptor #4 00 00000000 06E 00 00000000 06F FE 11111110 25470 00 00000000 071 Manufacture P/N 47 01000111 71 G72 Manufacture P/N 31 00110001 49 173 Manufacture P/N 30 00110000 48 074 Manufacture P/N 31 00110001 49 175 Manufacture P/N 53 01010100 83 S76 Manufacture P/N 54 01010100 84 T77 Manufacture P/N 4E 01001110 78 N78 Manufacture P/N 30 00110000 48 079 Manufacture P/N 31 00110001 49 17A Manufacture P/N 2E 00101110 467B Manufacture P/N 30 00110000 48 07C 0A 00001010 10

  • 27 IDK-1110WR User Manual

    Appendix A

    LCD

    ED

    ID

    Address Function Value Value Value Note7D 20 00100000 327E Extension Flag 00 00000000 07F Checksum 18 00011000 24

  • IDK-1110WR User Manual 28

  • www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject to change without notice.No part of this publication may be reproduced in any form or by any means,electronic, photocopying, recording or otherwise, without prior written permis-sion of the publisher.All brand and product names are trademarks or registered trademarks of theirrespective companies.© Advantech Co., Ltd. 2019

    IDK-1110WR-50WSA1Contents1 Overview1.1 General Description1.2 Display Characteristics1.3 Display Optical Characteristics1.3.1 Measuring Condition1.3.2 Measuring Equipment

    1.4 Block DiagramFigure 1.1 TFT LCD Module

    1.5 Absolute Maximum Ratings1.5.1 Absolute Max Rating

    1.6 Dimensions1.6.1 Front View1.6.2 Rear View

    2 Electrical Characteristics2.1 TFT LCD Module2.1.1 Power Specifications2.1.2 LVDS DC Electrical Characteristics2.1.3 LVDS AC Electrical Characteristics

    2.2 Backlight Unit2.2.1 Parameter Guidelines for LED Backlight

    3 Signal Characteristics3.1 Electrical Interface ConnectionTable 3.1: Connector

    3.2 The Input Data Format3.3 Interface Timing3.3.1 Timing CharacteristicsTable 3.2: Timing Characteristics

    3.3.2 Input Timing Diagram

    3.4 Power ON/OFF Sequence

    4 Touch Screen4.1 Touch Characteristics

    5 Touch Controller5.1 Touch Controller Characteristics5.2 Specifications5.3 Environmental Features5.4 Pin Assignments and Description5.4.1 Connector and LED Location5.4.2 Combo Interface Connector, JP1, Pins and Signal DescriptionsFigure 5.1 Board Mounted Header

    5.4.3 Touch Screen Connector, JP2, Pins and Signal Descriptions

    A LCD EDIDA.1 LCD EDID