update of master schedule and report from slac g. riddone 2008.10.08
TRANSCRIPT
![Page 1: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/1.jpg)
Update of master schedule and report from SLAC
G. Riddone2008.10.08
![Page 2: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/2.jpg)
Master Schedule
• See EDMS#844300, v3- Status- Master schedule by test station and by types- Rf components
![Page 3: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/3.jpg)
T18 - Alignment
• Optical measurement (from two sides) ex. T18#4 (OD 45 mm)
![Page 4: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/4.jpg)
T18 - Bonding
T18_vg2.4_disk_4Before bonding- OD 45 mm- 2 tuning holes per cell only
Then - Brazing of the couplers- Brazing of the studs
![Page 5: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/5.jpg)
Tuning C10 – KEK drawing
![Page 6: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/6.jpg)
Tuning C10
2. stud: the disk is systematically equipped with studs3. The tube ends at the tread part of the stud. TK of the tube is not defined
![Page 7: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/7.jpg)
Tuning C10
Test set-up for tuningPosition for “pulling”
Sliding hammer to push and pullDisks with
tuning studs
![Page 8: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/8.jpg)
Structure cell with 45° WG
![Page 9: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/9.jpg)
Symmetrical disk
No tuning was implemented
![Page 10: Update of master schedule and report from SLAC G. Riddone 2008.10.08](https://reader036.vdocuments.us/reader036/viewer/2022062423/5697bfd41a28abf838cacf37/html5/thumbnails/10.jpg)
NLCTA – T18 reverse and T26