update alert: firmware updates are posted the web on a ... · pdf filethe ma2 firmware for 2...

Installation Guide

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

that you check for firmware and/or install guide updates prior to installing this product.

Index

® Mazda is a its respective companyregistered trademark and property of .

The MA2 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALLMazda vehicles.

This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection 20on page for more information.

Vehicle Application Guide .....................................................................................................................................................02

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )

Type 1 ...................................................................................................................................................................................03T 2ype ...................................................................................................................................................................................06Type 3...................................................................................................................................................................................10Type 4...................................................................................................................................................................................12Type 5...................................................................................................................................................................................14Type 6...................................................................................................................................................................................16Type 7 ...................................................................................................................................................................................18

Programming

M ...........................................................................................................................................................20odule ProgrammingMethod 1 (using 1 key and Key2GO) - Recommended Method ..........................................................................................21M .......................................................................................................................................................22ethod 2 (using 2 keys)M .................................................................................................................................................23odule Reset & Hard ResetWeb Programming for Key2GO ...........................................................................................................................................24Feature & Option List ...........................................................................................................................................................25Feature Programming...........................................................................................................................................................25

LED Diagnostics .....................................................................................................................................26& Troubleshooting

L ................................................................................................................................28imited One-Year Consumer Warranty

Q ........................................................................................................................................................29uick Reference Guide

Rev.: 20170926

Platform: DBALL2

Firmware: MA2

© 2017 Directed. All rights reserved.

Vehicle Application Guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to eachyear allows you to determine which installation type should be used for your vehicle.

This feature is required if only one key is available. You can program the interface without the need for Key2Go if twokeys are present.

Key2 has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It usesGOan array of servers to generate a duplicate of the original key, the installation of a remote starter without having toallowinggive up a key.

The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.

All Key2 -compatible firmware are clearly indicated in the function list of each vehicle search result page and will alsoGOappear on the flash page. Any first-time user must re-register to gain access to Key2 , and some additional informationGOwill be required to complete the registration process, such as your Directed account number and store name. Key2GOrequires an XKLoader.

Refer to page 19 of this guide for instructions on how to program features using Key2 .GO

Vehicles

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

PK

-Im

mobil i

zer

Bypass-D

ata

No

Key

Req'd

CC

-Pow

er

Win

dow

sR

olld

ow

n

CC

-Pow

er

Win

dow

sR

ollu

p

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

Key2G

O

RS

-Sm

art

Sta

rt

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onitoring

ALL

Door

Pin

s

SS

-Entr

yM

onitoring

Hood

Pin

SS

-Entr

yM

onitoring

Tru

nk/H

atc

hP

in

SS

-Facto

ryA

larm

Trigger

Monitoring

ST

-Bra

ke

Sta

tus

(foot

bra

ke)

ST

-Door

Locks

Sta

tus

ST

-E-B

rake

Sta

tus

Mazda

2 1 1 1 1 • • • • • • D • • • • D • D •

3 1 1 1 1 • • • • • • • • • • D • • • • D • D •

3 5 5 5 5 5 5 • • • • D • • • • • •

5 1 1 1 1 1 1 • • • • • • D • • • •

5 5 5 5 5 5 • • • • D • • • • • •

6 1 1 1 1 1 • • • • • • • • • • D • • • • D • D •

6 2 2 2 2 2 2 • • • • D • • • • • •

B-Series 3 3 3 3 3 3 3 3 3 • • D • • • • •

CX-7 1 1 • • • • • • • • • D • • • • D • D •

CX-7 2 2 2 • • • • D • • • • •

CX-7 (Smart Key) 1 1 1 • • • • • • • • • D • • • • D • D •

CX-7 (Smart Key) 2 2 2 • • • • D • • • • •

CX-9 4 4 4 4 • • • • • • • • • D • • • • D • D •

CX-9 2 2 2 2 • • • • • D • • • • • •

CX-9 (Smart Key) 4 4 4 4 • • • • • • • • • D • • • • D • D •

CX-9 (Smart Key) 2 2 2 2 • • • • • D • • • • • •

MazdaSpeed3 2 2 2 2 • • • • • D • • • • • •

MazdaSpeed6 2 2 2 • • • • • D • • • • • •

MX-5 Miata 2 2 2 2 2 2 2 2 2 2 • • • • • D • • • • • •

RX-8 2 2 2 2 2 2 2 2 • • • • • D • • • • • •

Tribute 6 6 6 6 7 7 7 • • • D • • • • • •

Legend:

D: Data to Data (D2D) only AV: Horn & Lights Controls PK: Transponder & Immobilizer Override

•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls RS: Remote Start & Engine Controls

FOB: Sync CAN Interface w/ FOB Remote SS: Integrated Security & Monitoring

ST: Function/Feature Status

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Installation Type 1

Not required in D2D mode.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] Only if vehicle is equipped with OEM hood pin.[ ]3 Trunk release output is ONLY required if trunk is not supported in data.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the diagnostic connector.OBDII

Re

mo

te

Sta

rter

9: (+) Ignition InputPink:

10: (-) (Status) InputBlue/White: GWR

(+) 12V: 13Red:(+) 12V

(-) Ground: 14Black:

Passive Anti-Theft Security System ( ) connectorsPATS

1: (-) Lock InputGreen:

2: (-) Unlock InputBlue:

Aux 1 & 2 Output: ONLY if equipped with front one-touch powerwindows with auto up/down feature and global open.

[ ]1 ( ) Tach InpuAC t

(-) Door Status Input

(+) Brake Sense Input

Data : 11RX Orange/Black:

( ) Door Lock Output: 9MUX Violet/Brown:

[ ]1 ( ) Tach Output: 5AC Violet/White:

(-) Door Status Output: 3Green/White:

(+) Brake Status Output: 6Gray:

123456

Ground RX TX Ignition

A

8 7 6 5 4 3 2 1

Ground RX TXIgnition

B

(-) E-Brake Status Output: 1Black/White:

[ ]2 (-) Hood Status Output: 12Blue/Red:

[ ]2 (-) Hood Sense Input

(-) E-Brake Sense Input

Diagnosticconnector OBDII

(connector side view)

1 8

169

HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

HS CAN High: inP 6

HS CAN Low: in 1P 4

5: (-) Power ll-down InputViolet/Black: Windows Ro

4: (-) Power ll-up InputWhite/Violet: Windows Ro

C

P#: 2D65XKDTX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

2DBALL

4

Ignition Ground

3 2

TX RX

1

See ReferenceChart for Door LockMUX wire in vehicle.

(-) Ground(-) (Status)GWR

(+) Ignition Output

(+) Accessory Output

(+) Starter Output

(-) OutputLock

(-) Unl Outputock

(+) 12V Input

Ignition Connector

Refer to the Vehicle WiringReference Chart for wireand connector details.

( utput-) Trunk Release O [3]

(-) Parking Lights

Refer to the Vehicle WiringReference Chart for wireand connector details

Data : 10TX Yellow/Black:

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Type 1 - Vehicle Wiring Reference Chart

Function Wire Color Pin Polarity Location Color Pins

Mazda 2 2011-2014

12V Red 3 (+) Ignition switch. White 6

Ignition Black/Yellow 5 (+) Ignition switch. White 6

Accessory Black/Red 1 (+) Ignition switch. White 6

Starter Black/Blue 2 (+) Ignition switch. White 6

HS CAN High Red 6 Data OBDII. Black 16

HS CAN Low Blue 14 Data OBDII. Black 16

RX Gray 4 DataImmobilizer Module around ignition switch.

(PATS connector A).White 6

TX Green 3 DataImmobilizer Module around ignition switch.

(PATS connector A).White 6

Parking Light Brown/White 8 (-) Headlight switch. White 12

Trunk Release Orange/Blue 2 5-Wire BCM behind glove box. Gray 16

Door Lock (WO/Alarm) Pink 20 MUX BCM behind glove box. Gray 24

Door Lock (W/Alarm) Green 2 MUX BCM behind glove box. Gray 24

Mazda 3 2010-2013

12V Orange 8 (+) Ignition switch. White 8

Ignition Blue 1 (+) Ignition switch. White 8

Accessory White 6 (+) Ignition switch. White 8

Starter Lt. Green 5 (+) Ignition switch. White 8

HS CAN High White 6 Data OBDII. Black 16

HS CAN Low Red 14 Data OBDII. Black 16

RX Blue 1 DataImmobilizer Module around ignition switch.

(PATS connector C).White 4

TX Lt. Blue 2 DataImmobilizer Module around ignition switch.


Parking Light Gray 23 (-) BCM Above Driver kick panel. White 24

Trunk Release Brown 8 (-) BCM Above Driver kick panel. White 24

Door Lock (WO/Alarm) Lt. Green 14 MUX BCM Above Driver kick panel. White 24

Door Lock (W/Alarm) Green 13 MUX BCM Above Driver kick panel. White 24

Mazda 5 2011-2016

12V Blue/Black 8 (+) Ignition switch. White 8



Starter Blue/Red 5 (+) Ignition switch. White 8

HS CAN High Green/Yellow 6 Data OBDII. Black 16

HS CAN Low Red/Yellow 14 Data OBDII. Black 16

RX Gray 1 DataImmobilizer Module around ignition switch.


TX Blue/Orange 2 DataImmobilizer Module around ignition switch.


Parking Light Brown/Red 23 (-) BCM behind glove box. Blue 24

Trunk Release Violet/Yellow 8 (-) BCM behind glove box. White 24

Door Lock (W/Alarm) Blue 14 MUX BCM behind glove box. White 24

Wire Information Connector Information

Rev.: 20170926

Platform: DBALL2

Firmware: MA2





Mazda 6 2009-2013

12V Red/Blue 6 (+) Ignition switch. White 6

Ignition Green/Yellow 2 (+) Ignition switch. White 6

Accessory Pink/Yellow 4 (+) Ignition switch. White 6

Starter Gray/Red 1 (+) Ignition switch. White 6

HS CAN High Gray/Red 6 Data OBDII. Black 16

HS CAN Low Blue/Red 14 Data OBDII. Black 16

RX White/Green 3 DataImmobilizer Module around ignition switch.

(PATS connector B).White 8

TX Gray/Orange 4 DataImmobilizer Module around ignition switch.

(PATS connector B).White 8

Parking Light Black/White 14 (-) Headlight switch. White 17

Trunk Release Black/Red 28 (-) BCM Above Driver kick panel. White 30

Door Lock (WO/Alarm) Black/White 4 MUX BCM Above Driver kick panel. White 16

Door Lock (W/Alarm) Black 14 MUX BCM Above Driver kick panel. White 16

Mazda CX-7 2010-2011


Ignition Dk. Green/Yellow 2 (+) Ignition switch. White 6



HS CAN High Gray/Dk. Blue 6 Data OBDII. Black 16

HS CAN Low Dk. Blue/White 14 Data OBDII. Black 16

RX White/Dk. Green 1 DataImmobilizer Module around ignition switch.




Parking Light Black/Dk. Blue 14 (-) Headlight switch. White 17


Door Lock (WO/Alarm) Green/Red 14 MUX BCM Above Driver kick panel. White 30

Door Lock (W/Alarm) Black/White 11 MUX BCM Above Driver kick panel. White 30

Mazda CX-7 2010-2012 (Smart Key)


Ignition Dr. Green/Yellow 2 (+) Ignition switch. White 6



HS CAN High Gray/Dk. Blue 6 Data OBDII. Black 16

HS CAN Low Dk. Blue/White 14 Data OBDII. Black 16

RX White/Dk. Green 1 DataImmobilizer Module around ignition switch.




Parking Light Black/Dk. Blue 14 (-) Headlight switch. White 17


Door Lock (WO/Alarm) Green/Red 14 MUX BCM Above Driver kick panel. White 30

Door Lock (W/Alarm) Black/White 11 MUX BCM Above Driver kick panel. White 30

Installation Type 2

Re

mo

te

Sta

rter



(+) 12V: 13Red:(+) 12V


See ReferenceChart for Door Lock

wire in vehicle.MUX1: (-) Lock InputGreen:




[ ]2 (-) Hood Status Input

(+) Brake Status Input

TX: 10Yellow/Black:


RX: 11Orange/Black:






(-) E-Brake Status Input

P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL2

Diagnostic onnectorC OBDII(connector side view)

1 8

169


HS CAN Low: 4Tan:

HS CAN High: inP 6

HS CAN Low: in 1P 4

With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII

(-) Ground

(-) (Status)GWR

(+) Ignition Output


(+) Starter Output

(-) OutputLock

(-) Unl Outputock

(+) 12V Input

Ignition Connector



(-) Parking Lights Output


Re

mo

te

Sta

rter

4 123

Passive Anti-TheftSecurity System (PATS)

connector

RX: Pin 1

TX: Pin 2



Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2




Function Color Pin Polarity Location Color Pins

Mazda 6 2003-2008

12V Black or Black/Yellow 6 (+) Ignition switch. White 6






RX Orange/Blue or Gray 1 Data Immobilizer Module around ignition switch. White 4

TX Green or Yellow/Green 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Red/White 14 (-) Headlight switch. White 17

Trunk Release Yellow 1 (-) Trunk release switch. White 2

Door Lock (WO/Alarm) Lt. Green 7 MUX BCM drivers kick. White 24

Door Lock (W/Alarm) Blue or Blue/White 17 MUX BCM drivers kick. White 24

Mazda CX-7 2007-2009





HS CAN High Gray/Violet 6 Data OBDII. Black 16

HS CAN Low Blue/White 14 Data OBDII. Black 16

RX White/Green 1 Data Immobilizer Module around ignition switch. White 4

TX Gray/Orange 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Black/Red 14 (-) Headlight switch. White 17

Door Lock (WO/Alarm) Blue/Black or Green/Red 5 or 15 MUX BCM above Drivers kick. White 30

Door Lock (W/Alarm) Black/White 1 MUX BCM above Drivers kick. White 30










Parking Light Black/Red 14 (-) Headlight switch. White 17

Door Lock (WO/Alarm) Blue/Black or Green/Red 5 or 15 MUX BCM above Drivers kick. White 30

Door Lock (W/Alarm) Black/White 1 MUX BCM above Drivers kick. White 30

Mazda CX-9 2007-2010







RX Blue/Orange 1 Data Immobilizer Module around ignition switch. White 4

TX Blue/Yellow 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Brown or Brown/White 14 (-) Headlight switch. White 17

Trunk Release White/Green & White/Black 1 & 3 ShortPower liftgate switch, use relay to short White/Green and

White/Black together.White 6

Door Lock (WO/Alarm) Violet/White 26 MUX BCM above Drivers kick. White 30

Door Lock (W/Alarm) Lt. Green 12 MUX BCM above Drivers kick. White 30

Rev.: 20170926

Platform: DBALL2

Firmware: MA2















Trunk Release White/Green & White/Black 1 & 3 ShortPower liftgate switch, use relay to short White/Green and

White/Black together.White 6

Door Lock (WO/Alarm) Volet/White 26 MUX BCM above Drivers kick. White 30

Door Lock (W/Alarm) Lt. Green 12 MUX BCM above Drivers kick. White 30

Mazda MazdaSpeed3 2006-2009




Starter Gray/Black 5 (+) Ignition switch. White 6






Door Lock (WO/Alarm) Green/Red to Black/Blue N/A MUX Drivers kick panel. White N/A

Door Lock (W/Alarm) Black/Blue N/A MUX Drivers kick panel. White N/A

Mazda MazdaSpeed6 2006-2008

12V Black/Yellow 6 (+) Ignition switch. White 6






RX Orange/Blue or Gray 1 Data Immobilizer Module around ignition switch. White 4

TX Green or Yellow/Green 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Red/White 14 (-) Headlight switch. White 17

Trunk Release Yellow 1 (-) Trunk release switch. White 2

Door Lock (WO/Alarm) Lt. Green 7 MUX BCM drivers kick. White 24

Door Lock (W/Alarm) Blue or Blue/White 17 MUX BCM drivers kick. White 24

Mazda MX-5 Miata 2006-2015

12V White/Green 3 (+) Ignition switch. White 6

Ignition Green/White 2 (+) Ignition switch. White 6

Accessory Pink/Black 4 (+) Ignition switch. White 6

Starter White/Blue 1 (+) Ignition switch. White 6

HS CAN High Blue/White 6 Data OBDII. Black 16

HS CAN Low Green/Black 14 Data OBDII. Black 16

RX Blue/Orange or Violet 1 Data Immobilizer Module around ignition switch. White 4

TX Yellow/Black or Gray/Blue 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Brown/Black 14 (-) Headlight switch. White 17

Door Lock (WO/Alarm) Brown/White 10 MUX Keyless Control Module above drivers kick. White 27

Door Lock (W/Alarm) Gray/Red 3 MUX Keyless Control Module above drivers kick. White 27

Rev.: 20170926

Platform: DBALL2

Firmware: MA2





Mazda RX-8 2004-2011

Ignition Black/Yellow or Blue/Black 2 (+) Ignition switch. White 6

Accessory Blue/Green 6 (+) Ignition switch. White 6

Starter White/Blue 1 (+) Ignition switch. White 6

HS CAN High Blue/White 6 Data OBDII. Black 16

HS CAN Low Green/Black 14 Data OBDII. Black 16

RX Yellow/Black 1 Data Immobilizer Module around ignition switch. White 4

TX Blue/Orange 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Lt. Green 14 (-) Headlight switch. White 17

Door Lock (WO/Alarm) Lt. Green N/A MUX Driver door harness. N/A N/A

Door Lock (W/Alarm) Green/Red N/A MUX Driver door harness. N/A N/A

12V Green or Orange N/A (+) Drivers kick panel. N/A N/A

Installation Type 3

Re

mo

te

Sta

rter

(+) Ignition



(+) 12V: 13Red:(+) 12V





TX: 10Yellow/Black:


RX: 11Orange/Black:






P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL/2DBALL


1 8

169


HS CAN Low: 4Tan:

HS CAN High: inP 6

HS CAN Low: in 1P 4


Ignition Connector


(-) Ground

(-) (Status)GWR

(+) Ignition Output

(+) Accessory

(+) Starter Output

(+) Parking Lights

(-) OutputLock

(+) 12V Input

(-) Trunk Release Output [3]



4 123

RX: Pin 3

TX: Pin 4


connector

(-) Unl Outputock



Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2





Mazda B-Series 2002-2006

12V Yellow N/A (+) Ignition switch. White 6

Ignition Lt. Green/Violet N/A (+) Ignition switch. White 6

Accessory Gray/Yellow N/A (+) Ignition switch. White 6

Starter Red/Lt. Blue N/A (+) Ignition switch. White 6

HS CAN High (2004-2006) White/Lt. Green 6 Data OBDII. Black 16

HS CAN Low (2004-2006) Pink/Lt Green 14 Data OBDII. Black 16

RX Gray/Orange 3 Data Immobilizer Module around ignition switch. White 4

TX White/Lt. Green 4 Data Immobilizer Module around ignition switch. White 4

Parking Light Brown 3 (+) Headlight switch. White 11

Door Lock Pink/Yellow 5 (-) SJB (Smart Junction Box) Passenger kick panel. Black 30

Door unlock Pink/Green 9 (-) SJB (Smart Junction Box) Passenger kick panel. Black 30

Mazda B-Series 2007-2010

12V Red 2 (+) Ignition switch. Gray 13

Ignition White/Orange 1 (+) Ignition switch. Gray 13

Accessory Brown/Yellow 8 (+) Ignition switch. Gray 13

Starter Blue/White 5 (+) Ignition switch. Gray 13

HS CAN High (2004-2006) Blue/White 6 Data OBDII. Black 16

HS CAN Low (2004-2006) White 14 Data OBDII. Black 16

RX Blue/Gray 3 Data Immobilizer Module around ignition switch. Green 4

TX Violet/Brown 4 Data Immobilizer Module around ignition switch. Green 4

Parking Light Violet/White 5 (+) Headlight switch. White 10

Door Lock Gray/Yellow 5 (-) Driver kick panel. Black 32

Door unlock Violet/Gray 9 (-) Driver kick panel. Black 32

Installation Type 4

Re

mo

te

Sta

rter (-) (Status)GWR

(+) Ignition Output

(+) Accessory 2 Output

(+) Starter Output

( utput+) Brake O



(+) 12V: 13Red:(+) 12V

(-) Ground: 14Black:(-) Ground

(-) OutputLock







TX: 10Yellow/Black:


RX: 11Orange/Black:







P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL2


1 8

169


HS CAN Low: 4Tan:

HS CAN High: inp 6Red,

HS CAN Low: in 1p 4Blue,


(-) Unl Outputock

(+) 12V Input

(-) Ground

Ignition Connector


See ReferenceChart for Door LockMUX wire in vehicle.


(-) Parking Lights


4 123


connector

RX: , pin 1Blue/Orange

TX: , pin 1Blue/Yellow




Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2




Mazda CX-9 2011-2014




Accessory 2 Black/White 5 (+) Ignition switch. White 6







Door Lock (WO/ Alarm) Violet/White 26 MUX BCM in drivers kick. White 30

Door Lock (W/ Alarm) Lt. Green 12 MUX BCM in drivers kick. White 30

Brake Green/Yellow N/A (+) Driver kick panel. N/A N/A

Trunk Input Lt. Green/Red 10 (-) BCM in drivers kick. White 24

Trunk Release White/Green and White/Black 2 and 4 ShortPower lifgate switch, use relay to short

White/Green and White Black together.White 12

Mazda CX-9 (Smart Key) 2011-2014




Accessory 2 Black/White 5 (+) Ignition switch. White 6







Door Lock (WO/ Alarm) Violet/White 26 MUX BCM in drivers kick. White 30

Door Lock (W/ Alarm) Lt. Green 12 MUX BCM in drivers kick. White 30

Brake Green/Yellow N/A (+) Driver kick panel. N/A N/A

Trunk Input Lt. Green/Red 10 (-) BCM in drivers kick. White 24

Trunk Release White/Green and White/Black 2 and 4 ShortPower lifgate switch, use relay to short

White/Green and White Black together.White 12


Installation Type 5

Re

mo

te

Sta

rter



(+) 12V: 13Red:(+) 12V



wire in vehicle.MUX1: (-) Lock InputGreen:






TX: 10Yellow/Black:


RX: 11Orange/Black:







P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL2


1 8

169


HS CAN Low: 4Tan:

HS CAN High: inP 6

HS CAN Low: in 1P 4


MS CAN High: Orange/Green: 5

Ms CAN Low: Orange/Brown: 6

(-) (Status)GWR

(+) Ignition Output


(+) Starter Output

(-) Unl Outputock

(+) 12V Input

Ignition Connector



(-) Parking Lights


(-) Ground

MS CAN High: inP 3

MS CAN Low: in 1P 1

4 123


connector

RX: Pin 1

TX: Pin 2



Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2




Mazda 3 2004-2009




Starter Gray/Black 5 (+) Ignition switch. White 8



MS CAN High Gray/Violet 3 Data OBDII. Black 16

MS CAN Low Blue/White 11 Data OBDII. Black 16




Door Lock (WO/Alarm) Green/Red to Black/Blue N/A MUX Drivers kick panel. N/A N/A

Door Lock (W/Alarm) Black/Blue N/A MUX Drivers Kick panel. N/A N/A

Mazda 5 2006-2007







MS CAN High Blue/Whie 3 Data OBDII. Black 16

MS CAN Low Gray 11 Data OBDII. Black 16

RX Pink/Black 1 Data Immobilizer Module around ignition switch. White 4

TX Green 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Brown/Red 1 (-) Headlight switch. White 12

Door Lock Blue N/A MUX Drivers kick panel. N/A N/A

Mazda 5 2008-2010






HS CAN Low White 14 Data OBDII. Black 16

MS CAN High Violet 3 Data OBDII. Black 16

MS CAN Low Gray 11 Data OBDII. Black 16

RX Pink/Black 1 Data Immobilizer Module around ignition switch. White 4

TX Green 2 Data Immobilizer Module around ignition switch. White 4

Parking Light Brown/Red 1 (-) Headlight switch. White 12

Door Lock Blue N/A MUX Drivers kick panel. N/A N/A


Installation Type 6

Re

mo

te

Sta

rter



(+) 12V: 13Red:(+) 12V





TX: 10Yellow/Black:


RX: 11Orange/Black:






P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL2


Ignition Connector

Refer to the Vehicle WiringReference Information forwire and connector details.

(-) (Status)GWR

(+) Ignition Output


(+) Starter Output

(-) OutputLock

(-) Unl Outputock

(+) 12V Input

(-) Trunk Release Output [3]




1 8

169


HS CAN Low: 4Tan:

HS CAN High: pin 6White/Blue,

HS CAN Low: in 1p 4White,

MS CAN High: Orange/Green: 5

Ms CAN Low: Orange/Brown: 6

(-) Ground

MS CAN High:Gray/Orange, pin 3

MS CAN Low:Violet/Orange, pin 11

1 432

RX: pin 3Violet/Gray,

TX: pin 4Yellow/Orange,


connector

(+) Parking Lights



Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2




Mazda Tribute 2008-2011

12V Blue/Red 4 (+) Ignition switch. Black 7

Ignition White/Orange 1 (+) Ignition switch. Black 7

Accessory Violet/Green 6 (+) Ignition switch. Black 7

Starter Blue/White 7 (+) Ignition switch. Black 7

HS CAN High White/Blue 6 Data OBDII. Black 16

HS CAN Low White 14 Data OBDII. Black 16

MS CAN High Gray/Orange 3 Data OBDll Black 16

MS CAN Low Violet/Orange 11 Data OBDll Black 16

RX Violet/Gray 3 Data Immobilizer Module around ignition switch. Black 4

TX Yellow/Orange 4 Data Immobilizer Module around ignition switch. Black 4

Parking Light Violet/White N/A (+) Driver kick panel. N/A N/A

Door Lock Blue/Green 17 (-) Driver door harness. N/A N/A

Door unlock Yellow/Violet 4 (-) Driver door harness. N/A N/A

Rear liftgate Brown 7 (-) SJB (Smart Junction Box) right side of center console. Gray 26


Installation Type 7

(+) 12V: 13Red:(+) 12V

TX: 10Yellow/Black:


RX: 11Orange/Black:





P#: 2D65XKD

TX

(-) Ground

RX

(+)12V

10

RF

Prog Button.

LED

4

14

12

2

DBALL/2DBALL


1 8

169


HS CAN Low: 4Tan:

HS CAN High: inp 6White,

HS CAN Low: in 1p 4Black,



4 123

RX: pin 3Red/Black,

TX: pin 4Brown/Orange,


connector



Re

mo

te

Sta

rter (-) (Status)GWR

(+) Ignition Output

(+) Starter Output



(-) OutputLock







(-) E-Brake Status Input(-) Unl Outputock

(+) 12V Input

(-) Ground ( utput-) Trunk Release O [3]

(-) Parking Lights



Ignition Connector



wire in vehicle.MUX


Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2



Function Wire Color PinPolaritLocation Color Pins

Mazda Tribute 2005-2007

12V Red 4 (+) Ignition switch. Black 7

Ignition Lt. Green/Violet 1 (+) Ignition switch. Black 7

Accessory Black/Lt. Green 6 (+) Ignition switch. Black 7

Starter Tan/Lt. Blue 7 (+) Ignition switch. Black 7

HS CAN High White 6 Data OBDII. Black 16

HS CAN Low Black 14 Data OBDII. Black 16

RX Red/Black 3 Data Immobilizer Module around ignition switch. Green 4

TX Brown/Orange 4 Data Immobilizer Module around ignition switch. Green 4

Parking Light Brown N/A (+) Driver kick panel. N/A N/A

Door Lock/Unlock Pink/White MUX N/A Driver kick panel. N/A N/A


Module Programming

Refer to the LED Diagnostics section on page for more information and for troubleshooting purposes.26

Go to the next page t complete the module programming.o

Note for Knob style vehicles:Before starting the programming sequence, remove the metal key by sliding it out from the . TheOEM FOBremoval of the knob cover is necessary.

1- With the start knob in the position, remove the auxiliary key from the advanced key.OFF2- Remove the cover of the start knob by pulling it outward while pressing both buttons on each side of the knob.3- Proceed to module programming below.

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

When the flashing operation is successful, you can proceed with the programming instructions below.

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.

D2D Installation

W W Installation2

If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

3rd

10-pinD2D

1st

4th

12-pin14-pin

2nd

3rd

Flashing a module using your computer:

1. Connect the interface module to your computer using theXKLoader2.

2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module

3. Follow the instructions to select your vehicle, installationtype, and configure your options.

4. Once you have configured the firmware options, click on theFLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone ortablet.

3. Select and follow the on screenFLASH YOUR MODULEinstructions.

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Method 1 (using 1 key and Key2Go) - Recommended Method

1Solid

Wait until the LED turns solid red.ON

Note: Installations without HS CAN connections 5 times on the programming button,pressthe LED turns ON solid Orange and proceed to step 2.

You have successfully completed the programming sequence.module

The turns solid green, then turns once the module has been successfullyLED ON OFFprogrammed.

Solid Green Off

&

Key OUT

OF

F

START

ON

7

8

4

3

6

5

Turn removethe key to and it from the ignition barrel.OFF

Remove the / 2 from the vehicle and reconnect it to your computer. The web siteDBALL DBALL Directechswill automatically recognize that you are moving on to the second phase of the programming sequence.

Select the method and click on .Submit Key2 RequestGO

Once the configuration is completed, reconnect the / 2 to the vehicle.DBALL DBALL The flashes orange.LED

Key OUT

OF

F

START

ON

Flashes

2

Key IN

OF

F

START

ONTurn turnthe key to position then it to theOFF ON

position again. The flashes orange slowly.LED &

FlashesOrange (slowly)

&

Key IN

OF

F

START

ON

&

Key IN

OF

F

START

ONInsert turnthe key into the ignition barrel and it to the position. TheON LED

flashes green.FlashesGreen

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Important: Make sure all doors are closed on the vehicle before executing the programming sequence.

Insert turnthe first key and it to the position, wait untilONthe security light turns , then it. TheOFF LEDremoveflashes green.

Insert turnthe second key and it to the position, waitONuntil the security light turns , then it.OFF removeThe flashes orange.LED

1st ValidKey IN

OF

F

START

ON

2ndValidKey IN

OF

F

START

ON

1st ValidKey OUT

OF

F

START

ON

2ndValidKey OUT

OF

F

START

ON

The turns solid green for 3 seconds, then turnsLED ON OFFonce the module has been successfully programmed.Release the programming button. Solid

GreenOFF

FlashesOrange

&&

&

Release

Within seconds (if exceeded, restart programming at step 1, see page ):3 but no more than 10 seconds 12

Within seconds (if exceeded, restart programming at step 1, see page ):3 but no more than 10 seconds 12

&

OR

&Press

and hold

button

&Press

and hold

button

Remote Start*Ignition +12V

Jumper wireto +12V

Method 2 (using 2 keys)


FlashesGreen

&&

3

4

5

2

1Solid

Wait until the LED turns solid red.ON

Note: Installations without HS CAN connections 5 times on the programming button,pressthe LED turns ON solid Orange and proceed to step 2.

Automatic Transmission:the module programming button and then remote startPress & hold

the vehicule using the transmitter (keep holding the programmingbutton).

Manual Transmission:the module programming button and then applyPress & hold

(+)12 to the vehicle ignition wire with a jumper wire (keep holdingVthe programming button).

2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

Release the programming button. The turns solid red.LED ON

Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Module Reset

Hard Reset

2 & &Solid SolidRelease

Wait 3 seconds until the orange then release theLED turns solidONp The then turns solid red.rogramming button. LED ON

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

1 OR

If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button

D2D Installation

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

10-pinD2D

1st

5th

12-pin14-pin

2nd

3rd

4th

Rev.: 20170926

Platform: DBALL2

Firmware: MA2



3

2

1

Once the configuration is completed, reconnect the module.The LED ON solid .turns green for 3 seconds, then turns off

Click on .Submit Key2G RequestO

Remove the from the vehicle and reconnect it to your computer. The web site will automaticallymodulerecognize that you are moving onto the second phase of the programming sequence.

Web Programming (for Key2GO)

Solid x3 Secs

&Off

Refer to the LED Diagnostics section on page for more information and for troubleshooting purposes.26Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Feature Option List&

It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features ispossible using the information on this page.

* Default option

Feat. Operation Flashes / Option Description

1. Disabled* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.

2. All Unlocks all doors on first press.

1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the

beginning or end of the sequence; it must be controlled by the Remote Starter.

2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the

sequence, and relock after start and shutdown.

3. Enabled*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start

sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This

could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control

will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not

equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote

starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will

work perfectly with this option and will make it invisible to the user.

3

Smart

OEM

Alarm

Control

Unlock

Driver

Priority

2

1RF Output

Type

To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered

Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred

the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

sequence.OR

- Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

Feature ProgrammingProgramming

Button

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Rev.: 20170926

Platform: DBALL2

Firmware: MA2


LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

LED Diagnostics & Troubleshooting

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

LED Diagnostics & Troubleshooting

For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Limited Consumer WarrantyOne Year

Rev.: 20170926

Platform: DBALL2

Firmware: MA2


Quick Reference Guide


Vehicle Takeover

4

5

3

1

1

2

3

Stop the vehicle in a safe parking spotand put the gear in Park (P).

2

Ready todrive off

Pressremote start

*button

Pressremote start

*button

Press Unlockonbutton

either remote*

* Your aftermarket remote may differ from the model shown in the illustrations.

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

HO

LD

E vehicle withxitSmart Key

Enter vehicle

Pit Stop Mode

The Mode feature is practical when you need to stop and run an errand,Pit Stopbut wish to keep the engine running.

DBALL2-MA2

Close sendthe vehicle doors, hood and trunk, thenthe Remote Start command to start the vehicle*.

Send the Unlock command on the factory oraftermarket remote*.

Key IN

OF

F

START

ON

OR

Enter the vehicle, while making sure thefactory remote is inside with you.

Press the button to remote start the vehicle.*

The Parking Lights will flash to indicate theoncevehicle is now in P Modeit Stop .

Turn the ignition ON.

Depress putthe brake pedal, thecar in gear and drive off.

It is now safe to leave the exitengine running andthe vehicle with the in hand.factory remote

Note: We recommend that you always lock thedoors of your vehicle when leaving it unattended.

Quick Reference Guide


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for moreinformation.

Note that the information below is for Viper, Clifford and Python models. Icons andcommands may differ depending on the remote brand and model purchased. Referto your authorized installation center for more information.

Notes

DBALL2 MA2-

update alert: firmware updates are posted the web on a ... · pdf filethe ma2 firmware for 2...

Documents