universal garage door remote control - farnell element14 · dsq ezdoor-1 ©2009 reg no 277 4001,...

DSQ EZDOOR-1 ©2009 REG No 277 4001, Lewes, England.

‘EZ Door’‘EZ Door’‘EZ Door’‘EZ Door’

Universal Garage Door Remote ControlUniversal Garage Door Remote ControlUniversal Garage Door Remote ControlUniversal Garage Door Remote Control

ApplicationsApplicationsApplicationsApplications

• Replaces Garage Door Remotes

• Will fit any Garage door with a push button

• Universal Remote for many Door Controllers

• Universal Remote Control Kit

• 2 Rugged Keyfob Transmitters

• 2 Channel can operate 2 Doors

• 240Vac Power Supply included

• The Highest Security

• 64 Million Codes (superior to

many other Keeloq Systems)

• Up to 7 Additional Transmitters

• Range up to 30 Metres

• British made to ISO9001

DescriptionDescriptionDescriptionDescription

A versatile remote control, ideally suited to replacing Garage Door Remote controls.

Supplied ready to ‘plug and play’, installation is easy and takes just a few minutes.

The receiver is connected using standard ‘screw terminals’. All components are sup-

plied including a Power supply.

The system utilises the highest form of code hopping Keeloq protocol (superior to roll-

ing code) to ensure maximum security.

Manufactured in UK, and fully warranted for two years.

What’s IncludedWhat’s IncludedWhat’s IncludedWhat’s Included

• 2 x Pocket Keyfobs

• Control Box

• Power Pack

• 2metres Bell Wire

• Instructions




1. Fix EZDoor Receiver to the wall1. Fix EZDoor Receiver to the wall1. Fix EZDoor Receiver to the wall1. Fix EZDoor Receiver to the wall Fixe the EZdoor receiver unit Ideally next to the existing wall switch to which this will be connected to.

2. Connect Power to EZDoor Receiver 2. Connect Power to EZDoor Receiver 2. Connect Power to EZDoor Receiver 2. Connect Power to EZDoor Receiver Connect the wires from the power pack to the Power Input Terminals, Connections are as follows;

Connect the Black wire with white Stripe to the Screw terminal marked +12V

Connect the Black wire to the Screw terminal marked 0V

Tip: You may be able to take power connections directly from the back of your garage door operator as

many provide this therefore not requiring the powerpack..

3. Connect EZDoor Receiver to your Garage Door Switch3. Connect EZDoor Receiver to your Garage Door Switch3. Connect EZDoor Receiver to your Garage Door Switch3. Connect EZDoor Receiver to your Garage Door Switch Connect one of the white two way cables into the EZDoor � Output terminals ’1’ and ‘2’.

Connect the other end of the cable across the wall mounted push switch of your Garage Door Operator.

Tip: This connection can be across the wall mounted operator switch, or, across the terminals on the back of the operator unit which connect to the wall mounted push switch.

Installation is Easy! Simply follow these Instructions;Installation is Easy! Simply follow these Instructions;Installation is Easy! Simply follow these Instructions;Installation is Easy! Simply follow these Instructions;

1.1.1.1. Fix EZDoor receiver to the wallFix EZDoor receiver to the wallFix EZDoor receiver to the wallFix EZDoor receiver to the wall

2.2.2.2. Connect Power to EZDoor ReceiverConnect Power to EZDoor ReceiverConnect Power to EZDoor ReceiverConnect Power to EZDoor Receiver

3.3.3.3. Connect EZDoor Receiver to your Garage Door SwitchConnect EZDoor Receiver to your Garage Door SwitchConnect EZDoor Receiver to your Garage Door SwitchConnect EZDoor Receiver to your Garage Door Switch




Additional Installations for Special CasesAdditional Installations for Special CasesAdditional Installations for Special CasesAdditional Installations for Special Cases

If you have a Single Garage DoorIf you have a Single Garage DoorIf you have a Single Garage DoorIf you have a Single Garage Door: : : : and require both transmitter buttons to operate the same door,

then connect the � output as above, then, connect a jumper linking wire to connect the � Output ter-

minal ‘2’ to O Output terminal ‘2’ and another from � output ‘1’ to O output ‘1’

For TWIN Garage DoorsFor TWIN Garage DoorsFor TWIN Garage DoorsFor TWIN Garage Doors: : : : If you have a second wall mounted Push Switch, connect The a second

white two way cable into the EZDoor O output terminals ’1’ and ‘2’. Connect the other end of this cable

across the second wall mounted push switch of the Garage Door Operator.

If you have a 3 way wall Mounted Push Switch: If you have a 3 way wall Mounted Push Switch: If you have a 3 way wall Mounted Push Switch: If you have a 3 way wall Mounted Push Switch: Connect a jumper linking wire from EZDoor, �

Output terminal ‘2’ to O output terminal ‘2’. Connect a wire from this linking wire to the Com on the

Wall mounted switch. Next, connect a wire from EZDoor � Output terminal ‘1 to one side of the wall

mounted switch, & connect a wire from EZDoor O output terminal ‘1’ to the other side of the wall

mounted switch. Now pressing the � button on the transmitter will be the up command and the O but-

ton on the transmitter will be the down command.

Part NumberPart NumberPart NumberPart Number DescriptionDescriptionDescriptionDescription

QTX1 Transmitter 1 switch

QTX2 Transmitter 2 switch

Need Extra Transmitters?Need Extra Transmitters?Need Extra Transmitters?Need Extra Transmitters?

Learning additional Transmitter Keyfobs to the EZDoor Receiver UnitLearning additional Transmitter Keyfobs to the EZDoor Receiver UnitLearning additional Transmitter Keyfobs to the EZDoor Receiver UnitLearning additional Transmitter Keyfobs to the EZDoor Receiver Unit

Briefly place and remove the Link Cap on the LEARN pins to short the pins momentarily (as image below)

The receiver relays will click continuously.

Press any transmitter button once, the receiver relays will stop clicking.

Press the transmitter again, the receiver relays will ‘buzz’ briefly. After a short time delay for reset,

this transmitter will operate the system.

Warning: ensure nothing is connected to the LH Button output during the learn process (it will be oper-

ating at high speed during the learning process)

Erase ALL TransmittersErase ALL TransmittersErase ALL TransmittersErase ALL Transmitters Short the two learn pins on the receiver for 10 seconds then remove the short.

The receiver relays will ‘buzz’ briefly after the 10 seconds to indicate erasure.




Advanced Information Advanced Information Advanced Information Advanced Information ———— Further Reading Further Reading Further Reading Further Reading

The Universal Remote control system can be used for more than just garage doors, Using the relay out-

puts you can switch many things, including

Lights

Electric Gates / Barriers

Windows

LED Lights

Many other switching applications

Data OutputsData OutputsData OutputsData Outputs

Each output relay provides an isolated switch. Connections are Common (COM) and Normally Open (NO)

which close together when activated. Output 1 has an additional Normally Closed (NC) changeover con-

tact.

The action of the relay outputs is set by the Option link setting Jumper. A link is made / removed by the

small shorting link ‘cap’ placed over the pin header.

Option Link 1 Fitted = Momentary Operation (output operates while the transmitter pressed)

Option Link 1 Not Fitted = Latching Operation (output operates until the transmitter pressed again)

Please Note: The relay contacts in this unit are for functional use only and must not be used for isolation

purposes . They have a maximum switching capacity of 3A at 230Vac . It is your responsibility to ensure

the connection is safely within these limits. If in doubt consult a qualified electrician.

COM

NO

NC

Relay Connections whenTransmitter NOT Operating

COM

NO

NC

Relay Connections when Transmitter OPERATING

QuasarUK is an internet based company. All Sales / support and interface is via our website atQuasarUK is an internet based company. All Sales / support and interface is via our website atQuasarUK is an internet based company. All Sales / support and interface is via our website atQuasarUK is an internet based company. All Sales / support and interface is via our website at

www.quasaruk.co.ukwww.quasaruk.co.ukwww.quasaruk.co.ukwww.quasaruk.co.uk

for Sales:for Sales:for Sales:for Sales: for Support:for Support:for Support:for Support: Sales : Sales : Sales : Sales : [email protected]@[email protected]@quasaruk.co.uk Support : Support : Support : Support : [email protected]@[email protected]@quasaruk.co.uk

Support Tel: 0907 639 0000Support Tel: 0907 639 0000Support Tel: 0907 639 0000Support Tel: 0907 639 0000 Calls charged at £0.60 per minute from a BT landline other networks may

vary. Callers must be 18 or over and have the bill payers permission. Ser-

vice provided by StealthNET Ltd :08444150774

universal garage door remote control - farnell element14 · dsq ezdoor-1 ©2009 reg no 277 4001,...

Documents