unity ic30/ic300 dispensing system -...
TRANSCRIPT
Unity� IC30/IC300Dispensing System
Customer Product ManualPart 1092353_04
Issued 12/13
NORDSON CORPORATION DULUTH, GEORGIA USAwww.nordson.com
This document contains important safety informationBe sure to read and follow all safety information in thisdocument and any other related documentation.
Part 1092353_04 � 12/2013 Nordson CorporationAll rights reserved
Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General informationabout Nordson can be found on the Internet using the following address: http://www.nordson.com.
Address all correspondence to:
Nordson CorporationAttn: Customer Service11475 Lakefield Drive
Duluth, GA 30097
Notice
This is a Nordson Corporation publication which is protected by copyright. Original copyright date 2010.No�part�of�this�document may be photocopied, reproduced, or translated to another language without the prior written
consent of Nordson�Corporation. The�information�contained in this publication is subject to change without notice.
Trademarks
AccuJet, AeroCharge, Apogee, AquaGuard, Asymtek, Automove, Baitgun, Blue Box, Bowtie, Build‐A‐Part, CanWorks, Century, CF, CleanSleeve,CleanSpray, ColorMax, Color‐on‐Demand, Control�Coat, Coolwave, Cross‐Cut, cScan+, Dage, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber,
DuraPail, Dura‐Screen, Durasystem, Easy�Coat, Easymove Plus, Ecodry, Econo‐Coat, e.DOT, EFD, Emerald, Encore, ESP, e stylized, ETI‐stylized,Excel 2000, Fibrijet, Fillmaster, FlexiCoat, Flex‐O‐Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Fulfill, GreenUV, HDLV, Heli‐flow, Horizon, Hot Shot,
iControl, iDry, iFlow, Isocoil, Isocore, Iso‐Flo, iTRAX, Kinetix, KISS, Lean�Cell, Little�Squirt, LogiComm, Magnastatic, March, Maverick, MEG, Meltex,Microcoat, Micromark, Micromedics, Micro‐Meter, MicroSet, Millennium, MiniBlue, Mini Squirt, Mountaingate, NexJet, No-Drip, Nordson, Optimum,
Package of Values, Paragon, Pattern View, PermaFlo, PICO, PicoDot, Porous�Coat, PowderGrid, Powderware, Precisecoat, Printplus, Prism, ProBlue,Prodigy, Pro‐Flo, Program‐A‐Bead, Program‐A‐Shot, Program‐A‐Stream, Program‐A‐Swirl, ProLink, Pro‐Meter, Pro‐Stream, RBX, Rhino, Saturn,
Saturn with rings, Scoreguard, Sealant Equipment & Engineering, Inc, SEE and design, See‐Flo, Seal Sentry, Select�Charge, Select�Coat, Select Cure,Servo‐Flo, Shot‐A‐Matic, Signature, Slautterback, Smart‐Coat, Solder Plus, Spectrum, Speed‐Coat, SureBead, Sure Coat, Sure‐Max, Sure Wrap,
Tracking�Plus, TRAK, Trends, Tribomatic, TrueBlue, TrueCoat, Tubesetter, Ultra, UpTime, u‐TAH, Value Plastics, Vantage, VersaBlue, Versa‐Coat,VersaDrum, VersaPail, Versa‐Screen, Versa‐Spray,VP Quick Fit, Watermark, When you expect more., and X-Plane
are registered trademarks of Nordson Corporation.
Accubar, Active Nozzle, Advanced Plasma Systems, AeroDeck, AeroWash, Allegro, AltaBlue, AltaSlot, Alta Spray, Artiste, ATS, Auto‐Flo, AutoScan, Axiom, Best Choice, Blue Series, Bravura, CanPro, Champion, Check Mate, ClassicBlue, Classic IX, Clean�Coat, Cobalt, Controlled Fiberization, Control�Weave,
ContourCoat, CPX, cSelect, Cyclo‐Kinetic, DispensLink, Dry Cure, DuraBraid, DuraCoat, DuraPUR, Easy Clean, EasyOn, EasyPW, Eclipse, e.dot+,E‐Nordson, Equalizer, EquiBead, FillEasy, Fill�Sentry, Flow Coat, Fluxplus, Freedom, Get Green With Blue, G‐Net, Genius, G‐Site, IntelliJet, iON, Iso‐Flex,iTrend, Lacquer Cure, Maxima, Mesa, MicroFin, MicroMax, Mikros, MiniEdge, Minimeter, Multifill, MultiScan, Myritex, Nano, OmniScan, OptiMix, OptiStroke,Optix, Partnership+Plus, PatternJet, PatternPro, PCI, PharmaLok, Pinnacle, Plasmod, Powder�Pilot, Powder Port, Powercure, Process Sentry, Pulse Spray,
PURBlue, PURJet, Ready Coat, RediCoat, RollVIA, Quantum, Royal Blue, Select�Series, Sensomatic, Shaftshield, SheetAire, Smart, Smartfil, SolidBlue,Spectral, SpeedKing, Spray Works, StediFlo, StediTherm, Summit, SureFoam, Sure�Mix, SureSeal, Swirl�Coat, TAH, ThruWave, Trade�Plus, Trilogy,
Ultra FoamMix, UltraMax, Ultrasaver, Ultrasmart, Universal, ValueMate, Versa, Vista, Web Cure, YESTECH, and 2�Rings (Design) are�trademarks of Nordson�Corporation.
Designations and trademarks stated in this document may be brands that, when used by third parties for their own purposes, could lead to violation of the owners' rights.
In‐Sight is a registered trademark of Cognex Corporation.
Never Seez is a registered trademark of Bostik Inc.Parker Lubricant is a registered trademark of Parker Seal.
Viton is a registered trademark of DuPont Dow Elastomers. L.L.C.Windows is a registered trademark of Microsoft Corporation.
Table of Contents i
Part 1092353_04� 12/2013 Nordson Corporation
Table of Contents
Safety 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Safety Alert Symbols 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Responsibilities of the Equipment Owner 2. . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions, Requirements, and Standards 2. . . . . . . . . . . . . . . . . . . . .User Qualifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicable Industry Safety Practices 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use of the Equipment 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions and Safety Messages 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Practices 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Practices 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance and Repair Practices 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Safety Information 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Equipment Shutdown 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .General Safety Warnings and Cautions 7. . . . . . . . . . . . . . . . . . . . . . . .Other Safety Precautions 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .First Aid 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Labels and Tags 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Limitations of Use 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Additional Limitations of Use for PUR Adhesives 14. . . . . . . . . . . . . . . . . . .Unit Identification 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Key Components 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electro‐Magnetic Compliance Information 20. . . . . . . . . . . . . . . . . . . . . . . .Experience of Installation Personnel 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Customer‐Supplied Installation Components 20. . . . . . . . . . . . . . . . . . . . . .Contents of the Ship‐With Kit 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Position the Robot 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Install the Applicator on the Robot 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Install the Camera on the Robot 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mount the Unity Controller 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Make the Air Supply Connections 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Connect Cables 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Install Software 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Perform Initial System Power On 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contentsii
Part 1092353_04 � 12/2013 Nordson Corporation
Setup 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up the Unity Controller 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Controller to IC30 Operation 35. . . . . . . . . . . . . . . . . . . . . . . .Changing a Parameter in the User Mode 35. . . . . . . . . . . . . . . . . . . . . . .Changing a Parameter in the Administrator Mode 36. . . . . . . . . . . . . . .
Set Up the Robot Using JR C‐Points 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set the Robot Communications Cable Port 39. . . . . . . . . . . . . . . . . . . . .Set Up the Computer Communications Link with the Robot 40. . . . . . .Initialize the Robot (As Needed) 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Open a Robot Program File 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up Views 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjust the Adhesive Pattern Using the Zoom Function (As Needed) 42Move (Jog) the Robot (As Needed) 43. . . . . . . . . . . . . . . . . . . . . . . . . . . .Reprogram or Change the Adhesive Path (As Needed) 44. . . . . . . . . .
Run and Test the System 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up the Camera Using In‐Sight 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up the Network Connection 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up the Sensor Startup 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjust the Camera Focus or Brightness (Exposure) 50. . . . . . . . . . . . . .Calibrate the Camera 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Special Operating Considerations for PUR Adhesive 56. . . . . . . . . . . . . . .Daily Startup and Operation 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Responding to Alarms 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Placing the System in Setback 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Monitoring the System 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Daily Shutdown 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overnight Shutdown 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Long‐Term Shutdown 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Recommended Maintenance Schedule 62. . . . . . . . . . . . . . . . . . . . . . . . . .System Pressure Relief 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unity Controller Firmware Upgrade 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents iii
Part 1092353_04� 12/2013 Nordson Corporation
Troubleshooting 64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unity Controller Alarm Troubleshooting 64. . . . . . . . . . . . . . . . . . . . . . . . . . .General Troubleshooting 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Checking the Applicator Heater 67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Checking the Applicator RTD 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Using the Illustrated Parts Lists 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unity IC30/IC300 Dispensing System Assemblies 72. . . . . . . . . . . . . . . . .Unity IC30 Applicator Parts 74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unity IC300 Applicator Parts 76. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Camera Parts 78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cable Part Numbers 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nozzle Part Numbers 81. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Optional Accessories 81. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Recommended Spare Parts and Supplies 82. . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unity IC30/IC300 Dispensing System Specifications 83. . . . . . . . . . . . . . .Electrical Specifications 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dimensions 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Diagram of Internal Pneumatic Connections 85. . . . . . . . . . . . . . . . . . . . . . .Unity Controller Board Configuration Switch Settings 86. . . . . . . . . . . . . . .Schematic 87. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contentsiv
Part 1092353_04 � 12/2013 Nordson Corporation
Unity IC30/IC300 Dispensing System 1
Part 1092353_04� 12/2013 Nordson Corporation
Unity IC30/IC300 Dispensing System
Safety Read this section before using the equipment. This section containsrecommendations and practices applicable to the safe installation, operation,and maintenance (hereafter referred to as “use”) of the product described inthis document (hereafter referred to as “equipment”). Additional safetyinformation, in the form of task‐specific safety alert messages, appears asappropriate throughout this document.
WARNING! Failure to follow the safety messages, recommendations, andhazard avoidance procedures provided in this document can result inpersonal injury, including death, or damage to equipment or property.
Safety Alert Symbols
The following safety alert symbol and signal words are used throughout thisdocument to alert the reader to personal safety hazards or to identifyconditions that may result in damage to equipment or property. Comply withall safety information that follows the signal word.
WARNING! Indicates a potentially hazardous situation that, if not avoided,can result in serious personal injury, including death.
CAUTION! Indicates a potentially hazardous situation that, if not avoided,can result in minor or moderate personal injury.
CAUTION! (Used without the safety alert symbol) Indicates a potentiallyhazardous situation that, if not avoided, can result in damage to equipment orproperty.
Unity IC30/IC300 Dispensing System2
Part 1092353_04 � 12/2013 Nordson Corporation
Responsibilities of the Equipment Owner
Equipment owners are responsible for managing safety information, ensuringthat all instructions and regulatory requirements for use of the equipment aremet, and for qualifying all potential users.
Safety Information � Research and evaluate safety information from all applicable sources,
including the owner‐specific safety policy, best industry practices,governing regulations, material manufacturer's product information, andthis document.
� Make safety information available to equipment users in accordance with
governing regulations. Contact the authority having jurisdiction forinformation.
� Maintain safety information, including the safety labels affixed to the
equipment, in readable condition.
Instructions, Requirements, and Standards � Ensure that the equipment is used in accordance with the information
provided in this document, governing codes and regulations, and bestindustry practices.
� If applicable, receive approval from your facility's engineering or safety
department, or other similar function within your organization, beforeinstalling or operating the equipment for the first time.
� Provide appropriate emergency and first aid equipment.
� Conduct safety inspections to ensure required practices are being
followed.
� Re‐evaluate safety practices and procedures whenever changes are
made to the process or equipment.
Unity IC30/IC300 Dispensing System 3
Part 1092353_04� 12/2013 Nordson Corporation
User Qualifications
Equipment owners are responsible for ensuring that users:
� receive safety training appropriate to their job function as directed by
governing regulations and best industry practices
� are familiar with the equipment owner's safety and accident
prevention policies and procedures
� receive equipment and task‐specific training from another qualified
individual
NOTE: Nordson can provide equipment‐specific installation,operation, and maintenance training. Contact your Nordsonrepresentative for information
� possess industry‐ and trade‐specific skills and a level of experience
appropriate to their job function
� are physically capable of performing their job function and are not
under the influence of any substance that degrades their mentalcapacity or physical capabilities
Applicable Industry Safety Practices
The following safety practices apply to the use of the equipment in themanner described in this document. The information provided here is notmeant to include all possible safety practices, but represents the best safetypractices for equipment of similar hazard potential used in similar industries.
Intended Use of the Equipment � Use the equipment only for the purposes described and within the limits
specified in this document.
� Do not modify the equipment.
� Do not use incompatible materials or unapproved auxiliary devices.
Contact your Nordson representative if you have any questions onmaterial compatibility or the use of non‐standard auxiliary devices.
Unity IC30/IC300 Dispensing System4
Part 1092353_04 � 12/2013 Nordson Corporation
Instructions and Safety Messages � Read and follow the instructions provided in this document and other
referenced documents.
� Familiarize yourself with the location and meaning of the safety warning
labels and tags affixed to the equipment. Refer to Safety Labels and Tagsat the end of this section.
� If you are unsure of how to use the equipment, contact your Nordson
representative for assistance.
Installation Practices � Install the equipment in accordance with the instructions provided in this
document and in the documentation provided with auxiliary devices.
� Ensure that the equipment is rated for the environment in which it will be
used. This equipment has not been certified for compliance with theATEX directive nor as nonincendive and should not be installed inpotentially explosive environments.
� Ensure that the processing characteristics of the material will not create a
hazardous environment. Refer to the Material Safety Data Sheet (MSDS)for the material.
� If the required installation configuration does not match the installation
instructions, contact your Nordson representative for assistance.
� Position the equipment for safe operation. Observe the requirements for
clearance between the equipment and other objects.
� Install lockable power disconnects to isolate the equipment and all
independently powered auxiliary devices from their power sources.
� Properly ground all equipment. Contact your local building code
enforcement agency for specific requirements.
� Ensure that fuses of the correct type and rating are installed in fused
equipment.
� Contact the authority having jurisdiction to determine the requirement for
installation permits or inspections.
Operating Practices � Familiarize yourself with the location and operation of all safety devices
and indicators.
� Confirm that the equipment, including all safety devices (guards,
interlocks, etc.), is in good working order and that the requiredenvironmental conditions exist.
� Use the personal protective equipment (PPE) specified for each task.
Refer to Equipment Safety Information or the material manufacturer'sinstructions and MSDS for PPE requirements.
� Do not use equipment that is malfunctioning or shows signs of a potential
malfunction.
Unity IC30/IC300 Dispensing System 5
Part 1092353_04� 12/2013 Nordson Corporation
Maintenance and Repair Practices � Allow only personnel with appropriate training and experience to operate
or service the equipment.
� Perform scheduled maintenance activities at the intervals described in
this document.
� Relieve system hydraulic and pneumatic pressure before servicing the
equipment.
� De‐energize the equipment and all auxiliary devices before servicing the
equipment.
� Use only new Nordson‐authorized refurbished or replacement parts.
� Read and comply with the manufacturer's instructions and the MSDS
supplied with equipment cleaning compounds.
NOTE: MSDSs for cleaning compounds that are sold by Nordson areavailable at www.nordson.com or by calling your Nordson representative.
� Confirm the correct operation of all safety devices before placing the
equipment back into operation.
� Dispose of waste cleaning compounds and residual process materials
according to governing regulations. Refer to the applicable MSDS orcontact the authority having jurisdiction for information.
� Keep equipment safety warning labels clean. Replace worn or damaged
labels.
Equipment Safety Information
This equipment safety information is applicable to the following types ofNordson equipment:
� hot melt and cold adhesive application equipment and all related
accessories
� pattern controllers, timers, detection and verification systems, and all
other optional process control devices
Unity IC30/IC300 Dispensing System6
Part 1092353_04 � 12/2013 Nordson Corporation
Equipment Shutdown
To safely complete many of the procedures described in this document, theequipment must first be shut down. The level of shut down required varies bythe type of equipment in use and the procedure being completed. If required, shut down instructions are specified at the start of the procedure.The levels of shut down are:
Relieving System Hydraulic Pressure
Completely relieve system hydraulic pressure before breaking any hydraulicconnection or seal. Refer to the melter‐specific product manual forinstructions on relieving system hydraulic pressure.
De‐energizing the System
Isolate the system (melter, hoses, applicators, and optional devices) from allpower sources before accessing any unprotected high‐voltage wiring orconnection point.
1. Turn off the equipment and all auxiliary devices connected to theequipment (system).
2. To prevent the equipment from being accidentally energized, lock andtag the disconnect switch(es) or circuit breaker(s) that provide inputelectrical power to the equipment and optional devices.
NOTE: Government regulations and industry standards dictate specificrequirements for the isolation of hazardous energy sources. Refer to theappropriate regulation or standard.
Disabling the Applicators
NOTE: Adhesive dispensing applicators are referred to as “guns” in someprevious publications.
All electrical or mechanical devices that provide an activation signal to theapplicators, applicator solenoid valve(s), or the melter pump must bedisabled before work can be performed on or around an applicator that isconnected to a pressurized system.
1. Turn off or disconnect the applicator triggering device (pattern controller,timer, PLC, etc.).
2. Disconnect the input signal wiring to the applicator solenoid valve(s).
3. Reduce the air pressure to the applicator solenoid valve(s) to zero; thenrelieve the residual air pressure between the regulator and the applicator.
Unity IC30/IC300 Dispensing System 7
Part 1092353_04� 12/2013 Nordson Corporation
General Safety Warnings and Cautions
Table 1 contains the general safety warnings and cautions that apply toNordson hot melt and cold adhesive equipment. Review the table andcarefully read all of the warnings or cautions that apply to the type ofequipment described in this manual.
Equipment types are designated in Table 1 as follows:
HM = Hot melt (melters, hoses, applicators, etc.)
PC = Process control
CA = Cold adhesive (dispensing pumps, pressurized container, andapplicators)
Table 1 General Safety Warnings and Cautions
EquipmentType Warning or Caution
HM
WARNING! Hazardous vapors! Before processing any polyurethanereactive (PUR) hot melt or solvent‐based material through a compatibleNordson melter, read and comply with the material's MSDS. Ensurethat the material's processing temperature and flashpoints will not beexceeded and that all requirements for safe handling, ventilation, firstaid, and personal protective equipment are met. Failure to comply withMSDS requirements can cause personal injury, including death.
HM
WARNING! Reactive material! Never clean any aluminum componentor flush Nordson equipment with halogenated hydrocarbon fluids.Nordson melters and applicators contain aluminum components thatmay react violently with halogenated hydrocarbons. The use ofhalogenated hydrocarbon compounds in Nordson equipment cancause personal injury, including death.
HM, CAWARNING! System pressurized! Relieve system hydraulic pressurebefore breaking any hydraulic connection or seal. Failure to relieve thesystem hydraulic pressure can result in the uncontrolled release of hotmelt or cold adhesive, causing personal injury.
Continued...
Unity IC30/IC300 Dispensing System8
Part 1092353_04 � 12/2013 Nordson Corporation
General Safety Warnings and Cautions (contd)
Table 1 General Safety Warnings and Cautions (contd)
EquipmentType Warning or Caution
HM
WARNING! Molten material! Wear eye or face protection, clothing thatprotects exposed skin, and heat‐protective gloves when servicingequipment that contains molten hot melt. Even when solidified, hot meltcan still cause burns. Failure to wear appropriate personal protectiveequipment can result in personal injury.
HM, PC
WARNING! Equipment starts automatically! Remote triggering devicesare used to control automatic hot melt applicators. Before working onor near an operating applicator, disable the applicator's triggeringdevice and remove the air supply to the applicator's solenoid valve(s).Failure to disable the applicator's triggering device and remove thesupply of air to the solenoid valve(s) can result in personal injury.
HM, CA, PC
WARNING! Risk of electrocution! Even when switched off andelectrically isolated at the disconnect switch or circuit breaker, theequipment may still be connected to energized auxiliary devices.De‐energize and electrically isolate all auxiliary devices beforeservicing the equipment. Failure to properly isolate electrical power toauxiliary equipment before servicing the equipment can result inpersonal injury, including death.
HM, CA, PC
WARNING! Risk of fire or explosion! Nordson adhesive equipment isnot rated for use in explosive environments and has not been certifiedfor the ATEX directive or as nonincendive. In addition, this equipmentshould not be used with solvent‐based adhesives that can create anexplosive atmosphere when processed. Refer to the MSDS for theadhesive to determine its processing characteristics and limitations.The use of incompatible solvent‐based adhesives or the improperprocessing of solvent‐based adhesives can result in personal injury,including death.
Continued...
Unity IC30/IC300 Dispensing System 9
Part 1092353_04� 12/2013 Nordson Corporation
Table 1 General Safety Warnings and Cautions (contd)
EquipmentType Warning or Caution
HM, CA, PC
WARNING! Allow only personnel with appropriate training andexperience to operate or service the equipment. The use of untrainedor inexperienced personnel to operate or service the equipment canresult in injury, including death, to themselves and others and candamage to the equipment.
HM
CAUTION! Hot surfaces! Avoid contact with the hot metal surfaces ofapplicators, hoses, and certain components of the melter. If contactcan not be avoided, wear heat‐protective gloves and clothing whenworking around heated equipment. Failure to avoid contact with hotmetal surfaces can result in personal injury.
HM
CAUTION! Some Nordson melters are specifically designed toprocess polyurethane reactive (PUR) hot melt. Attempting to processPUR in equipment not specifically designed for this purpose candamage the equipment and cause premature reaction of the hot melt. Ifyou are unsure of the equipment's ability to process PUR, contact yourNordson representative for assistance.
HM, CA
CAUTION! Before using any cleaning or flushing compound on or inthe equipment, read and comply with the manufacturer's instructionsand the MSDS supplied with the compound. Some cleaningcompounds can react unpredictably with hot melt or cold adhesive,resulting in damage to the equipment.
HM
CAUTION! Nordson hot melt equipment is factory tested with NordsonType R fluid that contains polyester adipate plasticizer. Certain hot meltmaterials can react with Type R fluid and form a solid gum that canclog the equipment. Before using the equipment, confirm that the hotmelt is compatible with Type R fluid.
Unity IC30/IC300 Dispensing System10
Part 1092353_04 � 12/2013 Nordson Corporation
Other Safety Precautions � Do not use an open flame to heat hot melt system components.
� Check high pressure hoses daily for signs of excessive wear, damage, or
leaks.
� Never point a dispensing handgun at yourself or others.
� Suspend dispensing handguns by their proper suspension point.
First Aid
If molten hot melt comes in contact with your skin:
1. Do NOT attempt to remove the molten hot melt from your skin.
2. Immediately soak the affected area in clean, cold water until the hot melthas cooled.
3. Do NOT attempt to remove the solidified hot melt from your skin.
4. In case of severe burns, treat for shock.
5. Seek expert medical attention immediately. Give the MSDS for the hotmelt to the medical personnel providing treatment.
Unity IC30/IC300 Dispensing System 11
Part 1092353_04� 12/2013 Nordson Corporation
Safety Labels and Tags
Figure 1 illustrates the location of the product safety labels and tags affixed tothe equipment. Table 2 provides an illustration of the hazard identificationsymbols that appear on each safety label and tag, the meaning of thesymbol, or the exact wording of any safety message.
1
2
1
2
IC30
IC300
2
Figure 1 Safety labels and tags
Table 2 Safety Labels and Tags
Item Part Description
1. - - - - - -
Sign, power
2. - - - - - -
Sign, hot
Unity IC30/IC300 Dispensing System12
Part 1092353_04 � 12/2013 Nordson Corporation
Description This manual describes the installation and use of the Nordson UnityIC30/IC300 dispensing system. When necessary, the reader is referred tothe documentation supplied with other Nordson products or productssupplied by third parties.
The Unity IC dispensing system liquifies solid‐form polyurethane reactive(PUR) hot melt adhesive contained in 30‐cc syringes or in 300‐cc cartridgesand maintains the adhesive at the desired temperature. When the system isactivated, it uses compressed air to dispense a bead of adhesive as small as0.5 mm (0.020�in.) in width onto the surface of a product, usually in a small tomid‐sized electronics assembly application. The system includes:
� the Unity controller
� the Unity IC30 or IC300 applicator and MiniBlue module assembly
� the Unity robot with vision detection (camera) and feedback system (if
applicable—other robots are available)
� the following software applications for use on a Windows�‐based
computer: JR C‐Points (for the robot) and In‐Sight (for the camera) (ifapplicable)
These components combine to form a system that uses closed‐loop,algorithmic control to measure bead size and to then automaticallycompensate for adhesive viscosity and pressure to maintain consistent beadthickness.
Unity IC30/IC300 Dispensing System 13
Part 1092353_04� 12/2013 Nordson Corporation
1
4
2
6
3
3
4
5
Figure 2 Unity IC30/IC300 dispensing system components
1. Unity controller
2. IC30 applicator
3. IC300 applicator
4. Gantry‐style robot
5. Cantilever‐style robot
6. Camera
Unity IC30/IC300 Dispensing System14
Part 1092353_04 � 12/2013 Nordson Corporation
Intended Use
Unity Series dispensing systems are specifically designed to:
� Melt and pump solid‐form PUR hot melt adhesives contained in
syringes/cartridges that are engineered to be liquified and extruded attemperatures below 121 �C (250 �F)
� Be used with compatible equipment manufactured by Nordson
Corporation
� Be used in non‐explosive environments
The Unity IC30/IC300 dispensing system is virtually complete, but is intendedto be incorporated into machinery or assemblies by an integrator. Theequipment must not be placed into use in a member state of the EuropeanUnion until the parent machinery or assemblies have been declared by theintegrator to be in conformity with the applicable directives of the EuropeanCommission.
Limitations of Use
Use Unity Series dispensing systems only for the purpose for which they aredesigned. Unity Series dispensing systems should not be used:
� to melt or pump any material that creates a health or safety hazard
when heated
� in environments that will require the system to be cleaned using a
water wash or spray
Additional Limitations of Use for PUR Adhesives
When the maximum level of harmful substance concentration is exceeded,use a gas mask and air purifying equipment.
Unity IC30/IC300 Dispensing System 15
Part 1092353_04� 12/2013 Nordson Corporation
Unit Identification
See Figure 3. You will need the model and part number of the applicatorwhen requesting service or ordering spare parts and optional equipment. Theapplicator model and part number are indicated on the equipmentidentification plate.
IC30 IC300
Figure 3 Applicator equipment identification plate
Unity IC30/IC300 Dispensing System16
Part 1092353_04 � 12/2013 Nordson Corporation
Key Components
Figures 4-7 provide the name and the location of key system components.
6
8
9
7
2
5
4
3
1
10
Figure 4 Key components of a gantry‐style robot with an IC30 applicator and camera
1. Applicator body
2. Adhesive syringe latch
3. Solenoid valve
4. Nozzle
5. MiniBlue module
6. Robot
7. Robot controls
8. Moving plate
9. Camera
10. Robot power switch (on backof unit)
Unity IC30/IC300 Dispensing System 17
Part 1092353_04� 12/2013 Nordson Corporation
5
7
6
2
4
3
1
8
Figure 5 Key components of a gantry‐style robot with an IC300 applicator
1. Applicator body
2. Adhesive cartridge end cap
3. Solenoid valve
4. MiniBlue module
5. Robot
6. Robot controls
7. Moving plate
8. Robot power switch (on backof unit)
Unity IC30/IC300 Dispensing System18
Part 1092353_04 � 12/2013 Nordson Corporation
Key Components (contd)
8
4
1
567
2 3
Figure 6 Key components of the Unity controller (front view)
1. FAULT LED
2. ALARM LED
3. READY LED
4. Display
5. Up/down arrow keys
6. SET key
7. PAGE key
8. Purge switch
Unity IC30/IC300 Dispensing System 19
Part 1092353_04� 12/2013 Nordson Corporation
1
2 3 4 5
6
7
8
9
Figure 7 Key components of the Unity controller (top view)
1. Applicator connection
2. Enclosure power
3. Robot connection
4. Camera connection
5. Applicator connection
6. Connection for supply air fromregulator
7. Connection for tubing tosyringe/end cap
8. Exhaust port
9. Power switch
Unity IC30/IC300 Dispensing System20
Part 1092353_04 � 12/2013 Nordson Corporation
Installation Installation involves placing the system in the desired location and makingthe electrical and hydraulic connections.
Electro‐Magnetic Compliance Information
This system is classified as Class A, Group 2 under the European standardfor limits and methods of measurement, EN 55011.
Experience of Installation Personnel
The instructions provided in this section are intended to be used bypersonnel who have experience in the following subjects:
� Hot melt application processes
� Industrial power and control wiring
� Industrial mechanical installation practices
� Basic process control and instrumentation
Customer‐Supplied Installation Components
In addition to the components provided by Nordson Corporation, installationof the Unity IC30/IC300 dispensing system requires the followingcustomer‐supplied components:
� laptop computer
� communication cable to connect from the robot to the laptop
computer
� air pressure regulator and filter
� appropriate guarding and signage as required to prevent personal
injury during operation and service activities
Unity IC30/IC300 Dispensing System 21
Part 1092353_04� 12/2013 Nordson Corporation
Contents of the Ship‐With Kit
P/N 1005078
P/N 164045
P/N 734259
P/N 900586
P/N 971100
P/N 1094181
P/N 972287
1
2
3
4
5
6
7
8 P/N 1094186
P/N 9735009
P/N 98204610
P/N 98340111
Figure 8 Contents of the ship-with kit
1. 164045, CBL,ADPTR, 12P/6S, 10FT,T-STYLE (used to connect theapplicator cordset to the controller)
2. 734259, TUBE, AIR, M5, 6MM,MINIBLUE
3. 900586, TUBING, POLTHN, 6 MM ODX 4 MM, BLUE (25 FT)
4. 971100, CONN, MALE, 6 MM T X ¼UNI (used to install air dryer)
5. 972287, UNION, Y, 6 MM T X 6MM T X 6 MM T
6. 1005078, TUBING, PTFE, 6 MMOD X 1 MM WALL (1 FT)
7. 1094181, REGULATOR, FILTER,GAUGE, SMALL
8. 1094186, DRYER, AIR,DESICCANT, INLINE, ¼ NPT
9. 973500, COUPLING, PIPE,HYD, 1/4, STL, ZN (used toinstall air dryer)
10. 982046, SCR, HEX, CAP, M5X 14, BL
11. 983401, WASHER, LK, M,SPT, M5, STL, ZN
Unity IC30/IC300 Dispensing System22
Part 1092353_04 � 12/2013 Nordson Corporation
Position the Robot 1. Unpack and place the robot assembly at the desired location. Consider
the following when locating the robot assembly:
� The plant's electrical service must be rated to handle the power
required by the system.
� The operator must be able to safely reach and accurately monitor
moving parts and controls.
� The equipment should be installed in a location where the ambient
light will be stable during operational periods to ensure properfunction of the vision detection and feedback system.
� The equipment must be installed near a supply of clean, dry,
regulator, unlubricated compressed air.
� The equipment must be installed away from areas with strong drafts
or where sudden temperature changes occur.
� The equipment must be installed where it will be in conformance with
the ventilation requirements specified in the Material Safety DataSheet for the hot melt being used.
2. Install appropriate guarding and signage as required to prevent personalinjury (due to pressurized material, hot surfaces, pinch points, etc.) duringoperation and service activities.
Unity IC30/IC300 Dispensing System 23
Part 1092353_04� 12/2013 Nordson Corporation
This page intentionally left blank.
Unity IC30/IC300 Dispensing System24
Part 1092353_04 � 12/2013 Nordson Corporation
Install the Applicator on the Robot
See Figure 9 for IC30 applicators or Figure 10 for IC300 applicators. Use themounting block and screws supplied with the applicator to install theapplicator on the robot.
4
3
2
1
Figure 9 Installing an IC30 applicator on a gantry‐style robot
1. Gantry‐style robot
2. IC30 applicator
3. 983401, WASHER, LK, M,SPT, M5, STL, ZN
4. 982046, SCR, HEX, CAP, M5X 14, BL
Unity IC30/IC300 Dispensing System 25
Part 1092353_04� 12/2013 Nordson Corporation
4
2
1
5
4
2
4
3
4
4
Figure 10 Installing an IC300 applicator on a gantry- or cantilever-style robot
1. Gantry‐style robot
2. IC300 applicator
3. Cap screw, socket‐head, M5,22�mm
4. Screw, socket, M5 x 25
5. Cantilever‐style robot
Unity IC30/IC300 Dispensing System26
Part 1092353_04 � 12/2013 Nordson Corporation
Install the Camera on the Robot
See Figure 11. Use the screws supplied with the camera to install the cameraon the robot. Position the camera at the end of the bracket as shown.
5
2
1
4
3
7
14
4X
4X
4X
4X
4X
4X4X
6
7.6 cm(3 in.)
Figure 11 Installing the camera on a gantry‐style robot
1. Washer, lock, M, split, M4
2. Screw, socket, M4 x 16
3. Camera mounting bracket
4. Washer, flat, M, regular, M4
5. Screw, hex, M4 x 12
6. Camera
7. Nut, acorn, hex, M4
Unity IC30/IC300 Dispensing System 27
Part 1092353_04� 12/2013 Nordson Corporation
Mount the Unity Controller
See Figure 12. Unpack and mount the controller using the four bolt holeslocated on the back of the enclosure.
(10 in.)4 PL.
254 mm
(12.75 in.)323.9 mm
(0.313 in.)7.95 mm
Figure 12 Unity controller bolt mounting pattern
Unity IC30/IC300 Dispensing System28
Part 1092353_04 � 12/2013 Nordson Corporation
Make the Air Supply Connections
Using items from the ship‐with kit as needed, make the air supplyconnections shown in Table 3 and Figure 13. The air supply must be clean,dry, regulated, unlubricated compressed air. Set the operating air pressure to4.1 bar (60 psi).
Table 3 Air Supply Connections
Item No. inFig. 13
Pneumatic Connection Connect to... Then connect to...
1 Main air supply input Main air supply Air regulator input port
2 Air supply to applicatorsolenoid valve
Air pressure regulatoroutput (Y‐fitting)
Air input port on applicatorsolenoid valve
3 Air supply to controllerthrough air dryer
Air pressure regulatoroutput (Y‐fitting)
Air dryer input/output portsand controller air input port
4 Air supply to applicatoradhesive syringe (IC30) orend cap (IC300)
Air output port on top ofcontroller
Air fitting on top ofapplicator applicatoradhesive syringe (IC30) orend cap (IC300)
Unity IC30/IC300 Dispensing System 29
Part 1092353_04� 12/2013 Nordson Corporation
CONTROLLER TOP
IC30 APPLICATOR
4
2
IC30 APPLICATOR
6 mm
6 mm
AIR PRESSUREREGULATOR
3
6 mm
MAIN AIRSUPPLYSOURCE
4 mm
6-MMY-UNION
AND BRACKET
1
AIR DRYER
EXHAUST PORT
(SOLENOID VALVE)
(ADHESIVE SYRINGE)
IC300 APPLICATOR(SOLENOID VALVE)
IC300 APPLICATOR(ADHESIVE END CAP)
Figure 13 Air supply connections (refer to Table 3)
Unity IC30/IC300 Dispensing System30
Part 1092353_04 � 12/2013 Nordson Corporation
Connect Cables
See Figure 14 for IC30 applicators or Figure 15 for IC300 applicators, asapplicable. Make the cable connections shown in Table 4.
Table 4 Cable Connections
Item No. inFig. 14 or 15
Cable Connect to... Then connect to...
1 Robot controller cable Already connected tocontroller
I/O SYS port on the back ofthe robot
2 Robot system interlockcable
I/O‐S port on the back of therobot
Customer system‐readyinterlock
3 Unity controller powercable
Already connected tocontroller
240 VAC power outlet
NOTE: Do not use the poweroutlet on the back of therobot.
4 Robot power cable 240V cordset connector onback of robot
IC30 applicator: 240 VACpower outlet
IC300 applicator: 110 VACpower outlet
5 Camera Ethernet cable ENET connector on thecamera
Windows‐based computer
6 Camera power I/Obreakout cable
Already connected tocontroller
24VDC connector on thecamera
7 Robot communicationscable(customer‐supplied)
COM1 connector on the frontof the robot
USB or serial port onWindows‐based computer
8 Applicator cordset 6‐pin connector on theextension cable (P/N�164045)from the ship‐with kit
12‐pin connector on the top ofthe controller
9 Solenoid valve Already connected tocontroller
Quick‐disconnect on solenoidvalve connector
Unity IC30/IC300 Dispensing System 31
Part 1092353_04� 12/2013 Nordson Corporation
ROBOT FRONTROBOT BACK
I/O−S I/O SYSCOM1
12
CUSTOMERSYSTEM-READYINTERLOCK
3
240V
240VOUTLET
OUTLET
4
5
6
7
CAMERA
CONTROLLER TOP
IC30 APPLICATOR
COMPUTER8
9
Figure 14 Cable connections, IC30 applicator (refer to Table 4)
Unity IC30/IC300 Dispensing System32
Part 1092353_04 � 12/2013 Nordson Corporation
Connect Cables (contd)
ROBOT FRONTROBOT BACK
I/O−S I/O SYSCOM1
12
CUSTOMERSYSTEM-READYINTERLOCK
3
240V
110VOUTLET
OUTLET
4
5
6
7
CAMERA
CONTROLLER TOP
IC300 APPLICATOR
COMPUTER8
9
Figure 15 Cable connections, IC300 applicator (refer to Table 4)
Adhesive syringe latch
Unity IC30/IC300 Dispensing System 33
Part 1092353_04� 12/2013 Nordson Corporation
Install Software
Install any required software. Refer to the manuals supplied with otherequipment and/or any other applicable documentation.
If your system includes the In‐Sight camera, install the In‐Sight camerasoftware. The software and updates are available fromwww.cognexsensors.com/support.
If your system includes a Nordson Corporation robot, install the JR C‐Pointsrobot software using the supplied software installation CD.
Perform Initial System Power On
See Figures 4-7 as needed for the location of controls.
1. Turn on the robot.
2. Turn on the controller. The controller display will go through the startupscreens.
3. Turn on the air supply.
4. (IC30 applicator only) Load a flush syringe in the applicator as follows:
a. Open the adhesive syringe latch and remove the air cap.
b. Remove the caps from both ends of the flush syringe and insert thesyringe into the applicator.
c. Reinstall the air cap and close the latch.
Unity IC30/IC300 Dispensing System34
Part 1092353_04 � 12/2013 Nordson Corporation
Perform Initial System Power On (contd)
(IC300 applicator only) Load a flush cartridge as follows:
a. See Figure 16. Unscrew the adhesive cartridge end cap (1).
b. Heat the flush cartridge. Nordson Corporation recommends using anadhesive cartridge preheater, such as the PUR adhesive easypreheater available from 3M.
c. Place the needle pierce (3) on the bottom end of the cartridge (2),place the needle retaining nut (4) on the needle pierce, and tightenthe nut until it bottoms out.
d. Slide the cartridge, needle, and nut assembly into the applicatormanifold.
e. Reinstall the cartridge end cap and tighten it until it bottoms out. Theend cap will pierce the other end of the cartridge.
1
2
34
Figure 16 IC300 applicator adhesive cartridge installation/removal components
1. Adhesive cartridge end cap
2. Adhesive cartridge
3. Needle pierce 4. Needle retaining nut
5. If a cured adhesive warning exists at startup, reset the Elapsed Timeparameter to 0. Refer to Changing a Parameter in the User Mode underSetup.
6. Continue to the next section, Setup, to set up the system for yourapplication.
Unity IC30/IC300 Dispensing System 35
Part 1092353_04� 12/2013 Nordson Corporation
Setup Setup involves customizing the controller, robot, and camera settings for yourapplication.
Set Up the Unity Controller
The controller settings may be changed in two modes: user mode andadministrator mode. Use the following procedures to change the controllersettings as needed for your application.
Setting the Controller to IC30 Operation
On the UNIT TYPE page, ensure that the IC30 parameter is selected. Referto Changing a Parameter in the Administrator Mode for the procedure forchanging a parameter.
Changing a Parameter in the User Mode
See Figure 17.
1. Press PAGE until the desired parameter is displayed. Refer to Table�5 forthe parameters that can be accessed in the user mode.
2. Press SET to change the parameter.
3. Press the Up/Down arrows to scroll to the desired value.
4. Press SET to save the setting.
The display will briefly flash “Data successfully stored to memory.”
OUTPUT PRESSURE:15.00 PSI
Figure 17 Unity controller display and keys
Unity IC30/IC300 Dispensing System36
Part 1092353_04 � 12/2013 Nordson Corporation
Changing a Parameter in the Administrator Mode
See Figure 18.
1. Simultaneously press and hold the Up/Down arrows for at least5�seconds.
The display will briefly flash “Administrator Mode Enabled.”
2. Press PAGE until the desired parameter is displayed. Refer to Tables�5and 6 for the parameters that can be accessed in the administrator mode.
3. Press SET to change the parameter.
4. Press the Up/Down arrows to scroll to the desired value.
5. Press SET to save the setting.
6. Simultaneously press and hold the Up/Down arrows for at least5�seconds to exit the administrator mode.
The display will briefly flash “Administrator Mode Disabled.”
DISPLAYED UNITS:ENGLISH
Figure 18 Unity controller display and keys
Unity IC30/IC300 Dispensing System 37
Part 1092353_04� 12/2013 Nordson Corporation
NOTE: Refer to Changing a Parameter in the User Mode or Changing aParameter in the Administrator Mode under Set Up the Unity Controller forthe procedure for changing a parameter.
Table 5 Unity Controller User and Administrator Mode Parameters
Page Function/Description
PRESSURE:OFFSET:
Displays the actual pressure and the pressure offset. Allows you tochange the pressure by changing the offset.
Example: 5.53 PSI
TEMPERATURE:SETPOINT:
Displays the heater temperature and allows you to enter a temperaturesetpoint.
Example: 250 F
ELAPSED TIME: Displays how long a syringe/cartridge has been heated and allows you toreset the timer.
Example: 1 HR 18 Min.
TIMER MODE: Allows you to place the controller in the Run or Pause mode.
Values: RUNNING or PAUSED!
DESIRED BEAD WIDTH: Allows you to set the desired bead width.
Example: 0.77 mm
PRODUCT COUNT: Displays number of products processed. Only accurate if ”number ofbeads/product” parameter set correctly. Can be reset with SET key.
TEMPERATURE MODE: Allows you to place the system into the setback mode. The setback modereduces the temperature of the heaters by the amount entered in theTEMP SETBACK AMOUNT parameter.
Values: NORMAL and SETBACK
NO ALARMS ORMESSAGES
Displayed when no alarms or messages exist.
Unity IC30/IC300 Dispensing System38
Part 1092353_04 � 12/2013 Nordson Corporation
Set Up the Unity Controller (contd)
NOTE: Refer to Changing a Parameter in the Administrator Mode under SetUp the Unity Controller for the procedure for changing a parameter.
Table 6 Unity Controller Administrator Mode Only Parameters
Page Function/Description
UNIT TYPE: Used to set the controller for PURJet 30 or IC30/IC300 dispensing systemoperation.
Values: PURJet30 and IC30 (default)
TEMP SETBACK AMOUNT: Allows you to enter a temperature setback amount. When the system isplaced in the setback mode, the temperature setpoint will be reduced bythe number of degrees entered for this parameter.
Example: 100 F
USE CAMERA FEEDBACK? Used to set up the system to accept camera feedback if the system has acamera. If the system does not have a camera, this parameter should beset to NO.
Values: YES and NO
PSI STEP / MM ERROR: Used to set the proportional term for calculating adjustment amount.
Example: 13
MAX PSI STEP AMOUNT: Used to set the number of pressure increments the system willautomatically step up or down.
Example: 1.00 PSI
PRESSURE UNITS: Used to change the unit of measurement in which pressure is displayed.
Values: BAR or PSI
NOZZLE LENGTH: Used by system to set starting pressure.
NOZZLE DIAMETER: Used by system to set starting pressure.
GUN ON TIME Always set to 1 for IC30 operation.
GUN OFF TIME: Always set to 0 for IC30 operation.
FULL SCALE PRESSURE: Allows different pressure transducers to be used. This value should be thefull scale pressure of the pressure transducer that is used.
MAXIMUM PRESSURE: A warning is generated when the pressure is greater than this value.
SOLENOID POLARITY: The solenoid output can be inverted with this setting. NORMAL causesthe solenoid to energize when applying adhesive. INVERTED causes thesolenoid output to turn off when applying adhesive.
BEADS PER PRODUCT: Number of beads per product. Used to compute the product count.
Unity IC30/IC300 Dispensing System 39
Part 1092353_04� 12/2013 Nordson Corporation
Set Up the Robot Using JR C‐Points
NOTE: This section applies only if you are using a Nordson Corporationrobot.
NOTE: The JR C‐Points software does not allow you to undo or redo steps.Save your work often.
Set the Robot Communications Cable Port
See Figure 19.
1. Open Device Manager.
2. Expand Ports (COM & LPT).
3. Determine which port the robot communications cable is connected to,select that port, right‐click on the selection, and select Properties.
4. In the Communications Port (COM1) Properties dialog box, select thePort Settings tab and then select Advanced.
5. Select the correct COM Port Number. Only ports COM1 to COM4 arecompatible with the JR C‐Points software.
Figure 19 Screens used to set the COM port
Unity IC30/IC300 Dispensing System40
Part 1092353_04 � 12/2013 Nordson Corporation
Set Up the Computer Communications Link with theRobot 1. Select Robot > Com Status.
2. In the COM Status dialog box, select:
� Port: COM1 (or the port set up in the previous procedure)
� Parity: Non
� Stop bits: 1
Figure 20 COM Status dialog box
Initialize the Robot (As Needed)
Select Robot > Meca Initialize. Initializing the robot resets the X and Y axesto (0,0).
Unity IC30/IC300 Dispensing System 41
Part 1092353_04� 12/2013 Nordson Corporation
Open a Robot Program File 1. Open JR C‐Points by double‐clicking on the JR C‐Points for Dispensing
Icon.
2. Select File > Open.
NOTE: For detailed JR C‐Points software programming information, refer tothe robot product manual.
Set Up Views 1. Select View > Change View > Longitudinal View.
2. Select View > Visual Display.
The display looks like Figure 21.
Figure 21 JR C‐Points screen in longitudinal view
Unity IC30/IC300 Dispensing System42
Part 1092353_04 � 12/2013 Nordson Corporation
Adjust the Adhesive Pattern Using the Zoom Function(As Needed)
See Figure 22.
1. Use the following methods to zoom in on and fine‐tune the adhesivepattern:
� Use the Magnifier icon to zoom in on a particular location. To pan,
deselect the Magnifier icon and then click and hold with the cursor tomove the image.
� Use the Graph Grid icon to grid the graph.
NOTE: Double‐click in the white area next to a point to center the displayon that point.
2. Click on the Refresh icon after using any of these functions to update thedisplay.
Magnifier
Graph Grid
Magnification %
Refresh
Figure 22 Zoom tool bar
Unity IC30/IC300 Dispensing System 43
Part 1092353_04� 12/2013 Nordson Corporation
Move (Jog) the Robot (As Needed)
See Figure 23.
1. Select Robot > Jog.
2. Use any of following methods to move the robot:
� Select any position button
� Press the corresponding key on the computer keyboard
NOTE: Do not click on Register or use the Enter key. Doing so willregister the point.
� Enter the point number and select GO
� Enter the coordinates in the X and Y field and then select GO
� Select Robot > Jog; for a fast jog, press SHIFT + the corresponding
key on the keyboard (E, R, etc.)
� Select the point number and then select Robot > Go Move or Go
Move Plus
X
X Direction (Part Movement)
Z Direction (Up/Down)
Y Direction (Applicator)
Y
Figure 23 Jog screen
Robot menu
Unity IC30/IC300 Dispensing System44
Part 1092353_04 � 12/2013 Nordson Corporation
Reprogram or Change the Adhesive Path (As Needed)
NOTE: If the robot has a program or a modification is desired, theinformation can be downloaded from the robot.
1. Select Robot > Receive C&T Data > Receive.
2. Select Robot > Changing Mode > Teaching Mode.
3. Make the desired changes to the adhesive path.
To modify the type of point:
a. Click on the point to be changed (9, 10, or 11 in the example shown).
b. Select CP Passing Point, then right click and select an option.
c. Click on the Refresh icon view the new path.
Example: Figure 24 shows a before and after diagram of the Change toARC Point option.
9
10
11 9
10
11
Figure 24 Example of the Change to ARC Point option
To offset points:
a. Select the desired points and then select Edit > Offset Move.
b. Enter values for X, Y, and Z in the Offset Move dialog box.
To insert or add a point:
� To add a point in a selected position, select the position, then select
Edit > Insert Point.
� To add a point at end of the program, select Edit > Add Point.
4. Select Robot > Send C&T Data > Send.
5. Select Robot > Changing Mode > Switch Mode to change back to therobot mode.
Unity IC30/IC300 Dispensing System 45
Part 1092353_04� 12/2013 Nordson Corporation
Run and Test the System
Once the robot and controller are installed and set up, run the system andmake adjustments as needed until the bead pattern is correct. When thesystem is dispensing correctly, continue with the procedures in this section toset up and calibrate the camera so that it recognizes a correct bead pattern.
Unity IC30/IC300 Dispensing System46
Part 1092353_04 � 12/2013 Nordson Corporation
Set Up the Camera Using In‐Sight
This section applies only to the in‐Sight camera.
Set Up the Network Connection
NOTE: This procedure applies only to the first use of the In‐Sight software(Version�4.x).
1. Open In‐Sight 4.x.
2. Select System > Options > Job View and then select Makespreadsheet view default.
Figure 25 Options dialog box
Unity IC30/IC300 Dispensing System 47
Part 1092353_04� 12/2013 Nordson Corporation
3. Select View > In‐Sight Network.
4. Right‐click on In‐Sight Sensor and select Add Sensor/Device.
The Add Sensor/Device to Network dialog box appears.
5. Select the correct device name (example: camera xxx) and then selectCopy PC Network Settings.
The software adds the file to the IP Address and Subnet Mask fields inthe dialog box.
6. Change the last number of the address in the IP Address field to anysingle‐digit number other than 0.
Example: 2 (see Figure 26)
2
Figure 26 Add Sensor/Device to Network dialog box
7. Select Apply > OK > OK.
8. Double‐click on the camera icon to launch the Nordson camera consolesoftware.
Unity IC30/IC300 Dispensing System48
Part 1092353_04 � 12/2013 Nordson Corporation
Set Up the Sensor Startup
NOTE: This procedure applies only to the first use of the In‐Sight software(Version�4.x).
1. Select Sensor > Startup.
2. Select the appropriate file ( *. job).
3. In the Start up dialog box, select Online.
4. Select OK.
5. Select Sensors > Sensor film‐strip > Queue > Failed Results >Queue size > 20.
6. De‐select Clear Queue when placed online.
7. Select OK.
8. Select Sensor > User List and highlight Admin.
9. Select Edit.
10. In the User dialog box, select Show Custom View at Log On.
11. Select OK.
12. Select Sensor > Serial Port Settings.
13. In the Serial Ports 1 Settings dialog box, make the following selections:
� Baud: 9600
� Mode: Text
� Input Terminator: 59
� Output Terminator: 59
Figure 27 Serial Ports 1 Settings dialog box
Unity IC30/IC300 Dispensing System 49
Part 1092353_04� 12/2013 Nordson Corporation
This page intentionally left blank.
Unity IC30/IC300 Dispensing System50
Part 1092353_04 � 12/2013 Nordson Corporation
Adjust the Camera Focus or Brightness (Exposure) 1. Ensure that the camera is offline. When the camera is offline, the
Camera online/offline icon is disabled, as shown in Figure 28.
NOTE: Taking the camera offline allows you to force a trigger or placethe system in the live video mode. Either of these modes make manualadjustments easier. Picture quality and light stability are the keys toconsistent performance.
Camera online/offline icon (disabled—camera offline)
Triggericon(disabled)
Live videoicon (disabled)
Figure 28 Trigger, Live Video, and Camera online/offline icons (all disabled)
2. See Figure 29. Remove the camera lens cover (1).
3. Loosen the lens adjustment screws (2, 3)
4. Turn the Brightness and Focus adjustments clockwise orcounterclockwise until the picture on the In‐Sight software screen is clearand bright.
1
3
2
4
5
Figure 29 Adjusting the camera exposure
1. Lens cover
2. Aperture adjustment screw
3. Focus adjustment screw
4. Brightness adjustment
5. Focus adjustment
Unity IC30/IC300 Dispensing System 51
Part 1092353_04� 12/2013 Nordson Corporation
5. Tighten the lens adjustment screws (2, 3).
6. Click on the Camera online/offline icon to bring the camera back online.
Camera online/offline iconenabled—camera online
Figure 30 Camera online/offline icon enabled (camera online)
Unity IC30/IC300 Dispensing System52
Part 1092353_04 � 12/2013 Nordson Corporation
Calibrate the Camera 1. Obtain the actual bead width measurement in mm.
2. Ensure that the camera is online. When the camera is online, theCamera online/offline icon is enabled, as shown in Figure 31.
Camera online/offline iconenabled—camera online
Figure 31 Camera online/offline icon enabled (camera online)
3. Select both of the Camera control icons to display the Nordson camerascreen.
Camera control icons
Figure 32 Nordson Camera control icons and camera screen
Unity IC30/IC300 Dispensing System 53
Part 1092353_04� 12/2013 Nordson Corporation
4. Under MEASUREMENT CONTROLS, select Bead 1.
a. See Figure 33. Select the Bead 1 measurement box (1).
The box color changes to red (4).
b. Rotate the Bead 1 measurement box by clicking and holding therotation icon (3) and then rotating the box until the arrow under the Ypoints across the bead, as shown in Figure 33.
c. Double‐click inside the Bead 1 measurement box to exit the rotationmode.
5. Repeat step 4 for Bead 2.
NOTE: It is okay if the boxes overlap.
14
2
3
Figure 33 Bead measurement calibration
1. Bead 1 measurement box
2. Bead 2 measurement box
3. Rotation icon 4. Bead 1 measurement boxbeing rotated (red)
Unity IC30/IC300 Dispensing System54
Part 1092353_04 � 12/2013 Nordson Corporation
Calibrate the Camera (contd)
6. See Figure 34. Under MEASUREMENT CALIBRATION CONTROLS,enter the actual bead width in the Calibrate bead to (mm) field.
7. Select Calibrate.
8. Ensure that the camera screen looks like the one shown in Figure 34, inwhich all the MEASUREMENT DATA fields are populated.
The camera is now calibrated.
Figure 34 Nordson camera screen after calibration
Unity IC30/IC300 Dispensing System 55
Part 1092353_04� 12/2013 Nordson Corporation
This page intentionally left blank.
Robot power switch
1
2
1. Controller power switch2. Controller purge switch
Unity IC30/IC300 Dispensing System56
Part 1092353_04 � 12/2013 Nordson Corporation
Operation Before operating the system for the first time, ensure that you havecompleted the procedures in the Installation and Setup sections.
Special Operating Considerations for PUR Adhesive
Because the viscosity of PUR adhesive increases significantly when thesystem is at operating temperature, the applicator should be heated only foroperation or cleaning. If the applicator is held at operating temperature longerthan the life of the PUR adhesive, then the risk of cured material inside theapplicator increases.
However, even in the best operating scenario it is still likely that over time thePUR will occlude the inner adhesive passages, requiring the applicator to becleaned. When the applicator is cleaned, is it critical to remove cured PURadhesive from all adhesive passages, not just the adhesive passages insidethe module.
Daily Startup and Operation 1. Turn on the robot.
2. Turn on the controller. The controller display will go through the startupscreens.
NOTE: The controller always powers on in the user mode.
3. Turn on the air supply.
4. Allow the system to reach application temperature.
5. If a cured adhesive warning exists at startup, reset the Elapsed Timeparameter to 0. Refer to Changing a Parameter in the User Mode underSetup.
6. Verify that the temperature settings are at the desired value. Refer to SetUp the Unity Controller under Setup as needed.
Adhesive syringe latch on an IC30applicator
Unity IC30/IC300 Dispensing System 57
Part 1092353_04� 12/2013 Nordson Corporation
7. (IC30 applicator only) When the READY light turns on, place thecontroller purge switch in the on position until the rest of the material inthe flush syringe (used during shut down) is dispensed.
(IC300 applicator only) When the READY light turns on, place thecontroller purge switch in the on position and purge material from the theflush cartridge (used during shut down) for approximately five (5)minutes.
WARNING! Risk of burns. Wear heat‐protective gloves and clothing whenworking around heated equipment. Failure to avoid contact with hot metalsurfaces can result in personal injury.
8. (IC30 applicator only) Load an adhesive syringe in the applicator asfollows:
a. Open the adhesive syringe latch and remove the air cap.
b. Remove the caps from both ends of the adhesive syringe and insertthe syringe into the applicator.
c. Reinstall the air cap and close the latch.
Unity IC30/IC300 Dispensing System58
Part 1092353_04 � 12/2013 Nordson Corporation
Daily Startup and Operation (contd)
(IC300 applicator only) Load an adhesive cartridge in the applicator asfollows:
See Figure 35.
a. Unscrew the cartridge end cap (1).
b. Heat the adhesive cartridge. Nordson Corporation recommends usingan adhesive cartridge preheater, such as the PUR adhesive easypreheater available from 3M.
c. Place the needle pierce (3) on the bottom end of the adhesivecartridge (2), place the needle retainer nut (3) on the needle pierce,and tighten the nut until it bottoms out.
d. Slide the cartridge, needle, and nut assembly into the applicatormanifold.
e. Reinstall the cartridge end cap and tighten it until it bottoms out. Theend cap will pierce the other end of the cartridge.
1
2
34
Figure 35 IC300 applicator adhesive cartridge installation/removal components
1. Adhesive cartridge end cap
2. Adhesive cartridge
3. Needle pierce 4. Needle retaining nut
Robot START button
Unity IC30/IC300 Dispensing System 59
Part 1092353_04� 12/2013 Nordson Corporation
9. Place the product on the moving plate and press the START button onthe robot to run products.
Responding to Alarms
Refer to Troubleshooting for a list of alarms and recommended correctiveactions.
Placing the System in Setback
If the system will be operated again within the next 48 hours, place thesystem in setback during nonoperational periods.
� To place the system in setback, change the Temperature Mode
parameter to SETBACK.
� To take the system out of setback, change the Temperature Mode
parameter to NORMAL.
Refer to Changing a Parameter in the User Mode under Setup as needed. Ifthe system will not be used in next 48 hours, it should be shut down. Refer toShutdown.
1
2
1. Controller power switch2. Controller purge switch
Unity IC30/IC300 Dispensing System60
Part 1092353_04 � 12/2013 Nordson Corporation
Monitoring the System
Several parameters available on the controller are useful for systemmonitoring, including, but not limited to, the following:
� PRESSURE
� SETPOINT
� ELAPSED TIME
� CYCLE COUNT
� BATTERY VOLTAGE
Refer to Set Up the Unity Controller under Setup for a description of allcontroller parameters and the procedure for viewing or changing aparameter.
Shutdown
Because PUR adhesive reacts with moisture in the air, exposure of the PURadhesive in the system to air must be minimized. The procedures belowrepresent the best practices for overnight or long‐term (longer than overnight)shutdown.
Overnight Shutdown 1. Shut down the system and allow the applicator to cool, leaving the
current syringe/cartridge in the applicator. This will retain the seal andminimize the exposure to air.
2. The next morning, follow the Daily Startup and Operation procedureearlier in this section to install a new syringe/cartridge.
Long‐Term Shutdown 1. Place a large collection pan under the applicator.
WARNING! Risk of burns. When the last drops of adhesive are beingpurged, the pressurized air will cause some adhesive spray. Ensure that thecollection pan is large enough to shield the operator from the spray.
2. Place the controller purge switch in the on position until all adhesive isdispensed from the syringe/cartridge, then place the switch in the offposition.
Unity IC30/IC300 Dispensing System 61
Part 1092353_04� 12/2013 Nordson Corporation
3. (IC30 applicator only)
a. Open the applicator latch and, without putting pressure on thesyringe, remove the air cap.
b. Use a pick to remove any hardened adhesive from the syringe.
c. Install the air cap and close the latch
(IC300 applicator only)
a. Remove the cartridge end cap and then remove the cartridge, nut,and needle assembly.
b. Remove the retainer nut and needle pierce from the cartridge.
c. Use a pick to remove any hardened adhesive from the retainer nutand needle.
d. Reinstall the cartridge end end cap.
4. Remove the applicator nozzle and purge again to ensure that alladhesive is dispensed.
CAUTION! Ensure that the flushing material is compatible with the PURadhesive being used. Refer to the MSDS for both the adhesive and theflushing material.
5. Load a flush syringe/cartridge into the applicator.
6. Purge again until a clean flow of flush material is achieved. Leave someflush material in the syringe/cartridge.
7. Reinstall the nozzle and purge the system again to flush all PURadhesive out of the nozzle. Leave some flush material in thesyringe/cartridge.
8. Turn off the air supply.
9. Turn off the controller.
10. Turn off the robot.
Unity IC30/IC300 Dispensing System62
Part 1092353_04 � 12/2013 Nordson Corporation
Maintenance This section contains a recommended maintenance schedule andprocedures. Attempting any other maintenance procedures can result inequipment damage, improper system operation, or personal injury.
Recommended Maintenance Schedule
Table 7 provides recommended maintenance activities and a schedule forperforming those activities. Base how often you perform maintenance onyour operating conditions.
Table 7 Recommended Maintenance
Component Activity Interval Procedure
Robot andapplicator
Inspect forexternal damage
Daily When damaged parts pose a risk tothe operational safety of the unitand/or safety of personnel, switch offthe system and have the damagedparts replaced by qualified personnel.Use only original Nordson spare parts.
Clean the exterior Daily Remove adhesive residue only with acleaning agent recommended by theadhesive supplier. Heat with an airheater if necessary.
Remove dust, flakes, etc. with avacuum cleaner or a soft cloth.
Do not damage or remove warninglabels. Replace any damaged orremoved warning labels.
Replace the airsupply desiccanttube
When all material insidethe tube has turned pink
Relieve system pressure (refer toSystem Pressure Relief in this section)and replace the used desiccant tube,ensuring that all fittings are secure.Refer to Parts for the replacementdesiccant tube part number.
Camera Clean the cameralens cover
As needed Use a lens‐cleaning cloth to clean thecamera lens cover.
Unity controller Upgrade thefirmware
As needed Refer to Unity Controller FirmwareUpgrade in this section.
Air pressure regulator
1
2
1. Controller power switch2. Controller purge switch
Unity IC30/IC300 Dispensing System 63
Part 1092353_04� 12/2013 Nordson Corporation
System Pressure Relief
System pressure must be relieved before you can safely proceed with manytroubleshooting and service‐related activities. Follow this procedurewhenever you need to relieve system pressure.
WARNING! Risk of burns. Failure to relieve system pressure can cause hotmaterial to spray from a connecting point. Relieve system pressure beforeloosening or removing a hose, module, or any other part of a hot melt system.Wear heat‐protective clothing, safety goggles (ANSI Z87.1 or equivalent),and safety gloves.
1. Shut off the main air supply or set the air pressure regulator to zero (0).
2. Momentarily activate the purge switch on the controller.
3. When the service activity is completed, restore the system to normaloperation.
Unity Controller Firmware Upgrade
Visit www.enordson/support to download firmware updates, software utilities,and applicable instructions.
NOTE: The Unity controller displays the current software version at startup.
Unity IC30/IC300 Dispensing System64
Part 1092353_04 � 12/2013 Nordson Corporation
Troubleshooting Troubleshooting begins when the flow of adhesive from the applicator stopsor diminishes unexpectedly or when a control system alerts you of a problemthrough an alarm or visual display. This section covers only the mostcommon problems you may encounter. If you cannot solve a problem withthe information given here, contact your local Nordson representative forhelp.
For additional troubleshooting information, refer to the manuals provided withthe other equipment used in the hot melt system.
Unity Controller Alarm Troubleshooting
Refer to this table to troubleshoot the alarms generated by the controller.Refer to the next table for general troubleshooting.
Alarm Cause Corrective Action
CAMERA NOTRESPONDING!
Camera failed ping test Check all connections and thecamera software setup. Refer toSet Up the Camera Using In‐Sightas needed.
NO ALARMS ORMESSAGES
No None.
WARNING! ADHESIVE MAYBE CURED.
Timer has passed 16 hours. Check the adhesive quality andreplace the adhesivesyringe/cartridge as needed. Referto Daily Startup and Operation asneeded. Reset the timer. Refer toSet Up the Unity Controller underSetup as needed.
TIMER PAUSED! Timer has been paused Restart the timer. Refer to Set Upthe Unity Controller under Setup asneeded.
BAD CAMERA IMAGE! PressSET to clear.
Camera reported a bad image Press SET to clear the alarm.Check the camera setup and theproduct. Refer to Set Up theCamera Using In‐Sight as needed.
SHORTED RTD FAULT! Applicator RTD shorted Replace the RTD.
OPEN RTD FAULT! Applicator RTD open Replace the RTD.
TEMPERATURE TOO HIGH! Heater temperature is more than‐12��C (10 �F) above thetemperature setpoint
Allow time for the system to adjustto the temperature setpoint. Correctthe problem causing the excessiveheat. Refer to Set Up the UnityController under Setup as needed.
BEAD ERROR GREATERTHAN 10%
Displays when the bead width ismore than 10 percent of the desiredbead width.
Clear the alarm and note theoccurrence. If the message recursfrequently, troubleshoot thecamera.
Unity IC30/IC300 Dispensing System 65
Part 1092353_04� 12/2013 Nordson Corporation
General Troubleshooting
Refer to this table for general system troubleshooting. For troubleshootingbased on the alarms generated by the Unity controller, refer to the previoustable, Unity Controller Alarm Troubleshooting.
Problem Possible Cause Corrective Action
1. Applicator does notheat
System power not on Verify that the system power is turned on.
Loose electrical connection Verify that all electrical connections (cordsetsand cables) at the controller and the applicatorare secure.
Broken or missing electrical pins Check for broken or missing pins at all electricalconnections. Repair or replace damagedcomponents.
Applicator temperature setpointtoo low
Adjust the temperature setpoint as necessary.Refer to Set Up the Unity Controller under Setupas needed.
Incorrect configuration switchsettings
Ensure that the configuration switches on theUnity controller board are set as shown inFigure�46 under Technical Data.
2. Applicatorunderheats oroverheats
System in setback (standby)mode
Take the system out of the setback mode.
Applicator temperature setpointstoo low or too high
Adjust the temperature setpoints as necessary.Refer to Set Up the Unity Controller under Setupas needed.
Failed heater or RTD Check the applicator heater or RTD. Refer toChecking the Applicator Heater or Checking theApplicator RTD later in this section.
Incorrect configuration switchsettings
Ensure that the configuration switches on theUnity controller board are set as shown inFigure�46 under Technical Data.
3. Erratic bead width(from part to part)
Nozzle size incorrect Change the nozzle size to the appropriatediameter for the bead width.
Applicator too cold Adjust the temperature setpoint as necessary.Refer to Set Up the Unity Controller under Setupas needed.
Old PUR adhesive in system Clean or replace the nozzle, clean the adhesivepath, and/or replace the module.
Camera image incorrect Check the image lighting, focus the camera,and/or calibrate the camera.
Adhesive leaking under thesyringe flange
Check the syringe seal and clean the interfaceas needed.
Top of adhesive syringe/cartridgeplugged
Remove the cured layer of adhesive from the topof the adhesive syringe/cartridge.
Camera adjustment incorrect In the administrator mode, reduce the MAX PSISTEP AMOUNT. Refer to Set Up the UnityController under Setup as needed.
Continued...
Unity IC30/IC300 Dispensing System66
Part 1092353_04 � 12/2013 Nordson Corporation
General Troubleshooting (contd)
Problem Possible Cause Corrective Action
4. Bead too small Low input air supply Ensure that the input air pressure is greater than3.4 bar (50 psi).
Old PUR adhesive in system Clean or replace the nozzle, clean the adhesivepath, and/or replace the module.
Applicator too cold Adjust the temperature setpoint as necessary.Refer to Set Up the Unity Controller under Setupas needed.
Nozzle too small Change the nozzle to a larger size.
5. Bead width changeson the part
Robot speed inconsistent Check the program speed settings. Refer to SetUp the Robot Using JR C‐Points under Setup.
Applicator position too high/low Check the program height settings and/or checkthe height of the product. Refer to Set Up theRobot Using JR C‐Points under Setup.
6. No adhesive output Low or no input air supply Ensure that the input air pressure is greater than3.4 bar (50 psi).
No signal from robot Test the signal using the robot purge switch. Ifthe applicator purges, the problem is in therobot. Refer to the robot product manual totroubleshoot the robot. If the applicator does notpurge, check the setup. Refer to Installation asneeded.
Solenoid connection lost Check the red light on the solenoid valve. If thered light is not illuminated, replace the solenoid.
Old PUR adhesive in system Clean or replace the nozzle, clean the adhesivepath, and/or replace the module.
7. Leaks at bleed holeon module
Adhesive seal failure Replace the module.
8. Controller does notpower on
Open fuse Replace the open fuse. Refer to Parts for fusepart numbers.
Unity IC30/IC300 Dispensing System 67
Part 1092353_04� 12/2013 Nordson Corporation
Checking the Applicator Heater
NOTE: Cordsets for applicators with a platinum sensor arecustomer‐supplied. Refer to other documentation as needed.
1. Disconnect and lock out electrical power to the system.
2. Disconnect the applicator cordset.
3. See Figure 36. Use an ohmmeter to check the heater resistance andcontinuity at the heater pins on the cordset:
� If you measure low resistance, the heaters are operating normally.
Return to the procedure that referenced this check.
� If you measure high resistance or if an open circuit is indicated, there
may be a broken wire, a loose connection, or a defective heater.Continue to the next step.
34
5
21 HEATER
HEATER
RTD
RTD
GROUND
12
354
Figure 36 Pin positions on the applicator cordset
4. Remove the appropriate cordset connector hood and inspect the heaterwiring. Make sure there are no broken wires or loose connections andthat the heaters are wired correctly.
� If any wiring problems are found, correct the problems and restore the
system to normal operation.
� If no wiring problems are found, the heater is probably defective.
Replace the heater.
Unity IC30/IC300 Dispensing System68
Part 1092353_04 � 12/2013 Nordson Corporation
Checking the Applicator RTD
NOTE: Cordsets for applicators with a platinum sensor arecustomer‐supplied. Refer to other documentation as needed.
NOTE: You will need to know the temperature of the RTD to properlyperform this check.
1. Disconnect and lock out electrical power to the system.
2. Disconnect the applicator cordset.
3. See Figure 36. With the RTD at a known temperature, use an ohmmeterto measure the RTD resistance at the RTD pins on the cordset.
4. See Figure 37 (for nickel sensors) or Figure 38 (for platinum sensors) todetermine the correct resistance of the RTD based on its temperature:
� If the measured resistance is correct, the RTD is operating properly.
Return to the procedure that referenced this check.
� If the measured resistance indicates an open circuit, continue to the
next step.
5. Remove the appropriate cordset connector hood and check for looseRTD wires or wire connections. Tighten any loose connections.
6. Check the RTD resistance again. If the resistance is normal, the RTD isnow operating properly. If it is not, continue to the next step.
7. Disconnect the RTD wires, measure the resistance across them, andcompare the results to Figure 37:
� If the measured resistance is within the appropriate range, reconnect
the RTD wires, reinstall the cordset connector hood, and return to theprocedure that referenced this check.
� If the measured resistance is not within the appropriate range, replace
the RTD.
Unity IC30/IC300 Dispensing System 69
Part 1092353_04� 12/2013 Nordson Corporation
690504005
250
240
230
220
210
200
190
180
170
160
150
140
130
RE
SIS
TAN
CE
IN O
HM
S
310
300
290
280
270
260
250
240
230
350
340
330
320
RE
SIS
TAN
CE
IN O
HM
S
TEMPERATURE
TEMPERATURE
16 �C 23 �C 30 �C 37 �C 44 �C 52 �C 59 �C 66 �C 73 �C 81 �C 88 �C 95 �C 102 �C 109 �C 117 �C60 �F 73 �F 86 �F 99 �F 112 �F 125 �F 138 �F 151 �F 164 �F 177 �F 190 �F 203 �F 216 �F 229 �F 242 �F
268 �F 281 �F 294 �F 307 �F 320 �F 333 �F 346 �F 359 �F 372 �F 411 �F 424 �F 437 �F 450 �F385 �F 398 �F131 �C 138 �C 146 �C 153 �C 160 �C 167 �C 174 �C 182 �C 189 �C 196 �C 203 �C 211 �C 218 �C 225 �C 232 �C
Figure 37 RTD resistance vs. RTD temperature
Unity IC30/IC300 Dispensing System70
Part 1092353_04 � 12/2013 Nordson Corporation
Checking the Applicator RTD (contd)
205
200
195
190
185
180
175
170
165
160
155
150
145
140
135
130
125
120
115
110
105
10032 68 104 140 176 212 248 284 320 356 392 428 464
0 20 40 60 80 100 120 140 160 180 200 220 240
Temperature in Fo
Res
ista
nce
in o
hms
(pla
tinum
RT
D)
Temperature in Co
Figure 38 Platinum sensor resistance vs. sensor temperature
Note: Cordsets for applicators with a platinum sensor are customer supplied. Referto other equipment documentation as needed.
Unity IC30/IC300 Dispensing System 71
Part 1092353_04� 12/2013 Nordson Corporation
Parts
Using the Illustrated Parts Lists
To order parts, call the Nordson Customer Service Center or your localNordson representative. Use these five‐column parts lists, and theaccompanying illustrations, to describe and locate parts correctly. Thefollowing chart provides guidance for reading the parts lists.
The number in the Item column corresponds to the circled item numberin the parts list illustration. A dash in this column indicates that the item isan assembly.
The number in the Part column is the Nordson part numberyou can use to order the part. A series of dashes indicatesthat the part is not saleable. In this case, you must ordereither the assembly in which the part is used or a service kitthat includes the part.
The Description column describes the part andsometimes includes dimensions or specifications.
The Note column contains letters that refer to notes atthe bottom of the parts list. These notes provideimportant information about the part.
The Quantity column tells you how many of the partis used to manufacture the assembly shown in theparts list illustration. A dash or AR in this columnindicates that the amount of the item required inthe assembly is not quantifiable.
Item Part Description Quantity Note
— 0000000 Assembly A —
1 000000 � Part of assembly A 2 A
2 ‐ ‐ ‐ ‐ ‐ ‐ � � Part of item 1 1
3 0000000 � � � Part of item 2 AR
NS 000000 � � � � Part of item 3 2
NOTE A: Important information about item 1
AR: As Required
NS: Not Shown
Unity IC30/IC300 Dispensing System72
Part 1092353_04 � 12/2013 Nordson Corporation
Unity IC30/IC300 Dispensing System Assemblies
See Figure 39.
NOTE: Refer to Cable Part Numbers later in this section for a list of allcables that may be used with a Unity IC30/IC300 system.
Item Part Description Quantity Note
1 1120887 ENCLOSURE ASSY,UNITY 1
2 1094180 ROBOT,JR2303N, 300MM X 320MM X 100MM 1 A
3 1010791 ROBOT, JR2403, 400MM X 400MM X 150MM 1 A
4 1086442 GUN,UNITY,IC30-MINI BLUE 1 B
51120243 GUN,UNITY,IC300‐MINI BLUE 2 — C
1120256 GUN,UNITY,IC300‐MINI BLUE 2,PT100 — C
6 1122068 KIT, CAMERA ASSY, IN-SIGHT, 5100 1 D
NS 1120889 KIT, SHIP WITH, IC30 1 E
NOTE A: Refer to the robot product manual for parts information.
B: Refer to Unity IC30 Applicator Parts.
C: Refer to Unity IC300 Applicator Parts.
D: Refer to Camera Parts.
E: Refer to Contents of the Ship‐With Kit under Installation for an illustration and parts list.
NS: Not Shown
Unity IC30/IC300 Dispensing System 73
Part 1092353_04� 12/2013 Nordson Corporation
55
2
3
6
1
4
2
Figure 39 Unity IC30/IC300 dispensing system assemblies
Unity IC30/IC300 Dispensing System74
Part 1092353_04 � 12/2013 Nordson Corporation
Unity IC30 Applicator Parts
See Figure 40.
Item Part Description Quantity Note
— 1086442 GUN,UNITY,IC30‐MINI BLUE —
1 1094155 � MANIFOLD,HEATED,30CC SYRINGE 1
2 1086856 � STANDOFF, SWING LATCH,3M SYRINGE 2
3 1086857 � LATCH,SWING,3M SYRINGE 1
4 1086870 � CAPSCRM,SOC HD/FLANGED,M5X10,STL, BLK 2
5 1086871 � COVER,ELECTRICAL,3M SYRINGE 1
6 201407 � CORD SET KO/MI/0,51/1 X NI120/1 X TS 1
7 982308 � SCR,PAN,REC,M4X10,ZN 2
8 983403 � WASHER,LK,M,SPT,M4,STL,ZN 2
9 1086896 � INSULATOR,MANIFOLD/BRACKET,3MSYRINGE
1
10 985267 � PIN,DOWEL,.250X1.000,H&G 2
11 1097793 � BRACKET, GUN MOUNT, JR2403 1
12 1002812 � SCREW,BUTTON HEAD,M6 X 25MM,BL 2
13 1094183 � SOLENOID,VALVE,2POSITION,3WAY 1
14 982658 � SCR,SKT,M3X16,ZN 2
16 981907 � SCR,DRIVE,RD,4X .250,ZN 6
17 290083 � SIGN,DANGEROUS VOLTAGE 2
18 178475 � TAG,HOT SURFACE 2
19 184799 � INFORMATION PLATE 1
20 1065633 � COMPOUND,HEATSINK,10CC SYRINGE 1
21 1094156 � CLAMP,WEDGE,45 DEG,30CC SYRINGE 1
22 1023307 � ELBOW, MALE,6 MM TUBE X G 1/8 2
23 815945 � SCR,SKT,M5X20,ZN 2
24 1095703 � KIT,REPL,MODULE,MINIBLUE2,BAS 1
25 939586 � CONNECTOR,PLASTIC,2 STA. 1
26 972862 � EYELET,.069/.089OD X .187LG 4
27 1086749 � HEATER,240V,250W, .50D,4.38LG 1
28 982091 � SCR,PAN,SLT,M3X6,ZN 1
29 983400 � WASHER,LK,M,SPT,M3,STL,ZN 1
30 1086859 � SETSCRM,M4 X 9,BALL,SPRING PLUNGER,STL
1
31 1094185 � TUBING,6MM,4MM,HIGH FLEX,100C 1 ft
32 982847 � SCR,PAN,REC,M4X10,W/LW 1
33 1094222 � CAP,AIR,3M 30CC SYRINGE 1
34 7103784 � PLUG-TYPE THREAD-IN FTG. -G-D06-G1/8-0000 1
35 972310 � CONN,MALE,UNIVERSAL ELBOW,6MM T X M5 1
36 734262 � MUFFLER,M5,SD 2
37 1094157 � INSERT,SEAL,30CC SYRING 1
38 1036298 � PANDUIT,CORR LOOM TUBING 1IN 8
40 940121 � O RING,VITON,.364ID X .070W,BR,5060 2
41 933006 � TERMINAL,RINGTONG,NON,22-18, 6 1
42 941161 � O RING,VITON, .750X .938X.094, -116 1
NS 1121331 � CABLE,SOLENOID,IC30 A
NOTE A: This cable is used to connect the applicator solenoid valve to the controller.
NS: Not Shown
Unity IC30/IC300 Dispensing System 75
Part 1092353_04� 12/2013 Nordson Corporation
2
20
40
1
4
35
6
7 8
9
SEE ALTERNATE VIEW
17
19
21
22
( CORDSET )NOT SHOWN
31
CUT TUBING TO FIT
24
12
14
23
32
37
35
3613
42343311
18
DETAIL B
( BALL PLUNGER )
30
10
ALTERNATE VIEW
WIRING DIAGRAM
HEATER
RTD
( ITEM 6 )
20
28
20
29
41
27 25
APPLY TO THIS ENTIRE SURFACE
APPLY TO THIS ENTIRE SURFACE
26
Figure 40 Unity IC30 applicator parts
Unity IC30/IC300 Dispensing System76
Part 1092353_04 � 12/2013 Nordson Corporation
Unity IC300 Applicator Parts
See Figure 41,
Item Part Description Quantity Note
— 1120243 GUN,UNITY,IC300‐MINI BLUE 2 —
— 1120256 GUN,UNITY,IC300‐MINI BLUE 2,PT100 —
1 1120233 � SLEEVE,HEATED,IC300CC 1
2 1120234 � BRACKET,ROBOT MOUNTING,IC300CC 1
3 1120235 � NEEDLE,PIERCE,IC300CC 1
4 1120236 � NUT,NEEDLE RETAINER,IC300CC 1
5 1120237 � BLOCK,MOUNT,INSULATOR,SOLENOID 1
6 1120238 � SOLENOID,4 PORT,VALVE,3.2W,24V,MPLUG
1
7 142278 � ADAPTER,BAYONET,1/8NPT,1.0-IN 1
8 981907 � SCR,DRIVE,RD,4X .250,ZN 6
9 982646 � SCR,SKT,M5X22,BL 2
10 982085 � SCR,SKT,M5X25,BL 7
11 1121329 � CABLE ASSY, SPL,3CON 1 A
12 1120241 � CAP,END,REACTIVE ADHESIVE,3M 1
13
1067913 � CORDSET,UA,M‐STYLE,PT100,240V,700W,SQR (PT100 applicator)
1
1067912 � CORDSET,UA,T-STYLE,NI120,240V,700W(NI120 applicator)
1
14 1095703 � KIT,REPL,MODULE,MINIBLUE2,BAS 1
15 1023307 � ELBOW, MALE,6 MM TUBE X G 1/8 1
16 290083 � sign,dangerous voltage 2
17 178475 � TAG,HOT SURFACE 3
18 184799 � INFORMATION PLATE 1
19 1120244 � CONNECTOR,MALE,6MM,TUBEXG1/8,VITON
1
20 1005078 � TUBING,PTFE,6MM ODX 1 MM WALL 1 ft
21 940090 � O RING,VITON,.208ID X .070W,BR,10409 1
22 971790 � UNION,STRAIGHT,6MM T 2
23 1120240 � MANIFOLD,MODULE,MOUNT,IC300CC, SMCOPT
1
24 1108371 � LUBRICANT,NEVER-SEEZ,NSF-H1,FOODGRADE
1
25 900298 � COMPOUND,HEAT SINK,5 OZ TUBE,11281 1
26 1120201 � LUBRICANT,O-RING,NSF-H1,10 ML TUBE 1
27 972815 � FERRULE,WIRE,18AWG,INS,RED 2
28 982337 � SCR,PAN,REC,M4X8M,ZN 1
29 983421 � WASHER,LK,M,EXT,M4,STL,ZN 1
30 983047 � WASHER,FLT,M,REG,4,SSTL 1
31 982157 � SCR,SKT,M3X14,BL 2
NOTE A: This cable is used to connect the applicator solenoid valve to the controller.
NS: Not Shown
Unity IC30/IC300 Dispensing System 77
Part 1092353_04� 12/2013 Nordson Corporation
5.ITEM 9 USE 2X WHEN ATTACHING TO GANTRY STYLE ROBOT.6.USE ITEM 10 IN THESE LOCATIONS 2 X WHEN ATTACHING TOCANTILEVER STYLE ROBOT.7.CUT ITEM 20 TO 5 INCH LENGTH.
NOTES:1.APPLY THREAD LUBRICANT(ITEM 24) TO ALL STRAIGHT THREADS.2.APPLY HEATSINK COMPOUND(ITEM 25)TO HEATER AND RTD ELEMENT OF ITEM 13.3.APPLY O-RING LUBE(ITEM 26) TO ALL O-RINGS.
2219
9
6
27
31
5
3
4
28
29
30
7
18
1716
1
20
15
14
10
21
23
10
8
13
22
8
10
REFERENCE ONLYCARTRIDGE SHOWN
SUPPLIED
SUPPLIED
2
12
11
17
13
1020
10
16
8
17
WITH ITEM14
WITH ITEM 6
Figure 41 Unity IC300 applicator parts
Unity IC30/IC300 Dispensing System78
Part 1092353_04 � 12/2013 Nordson Corporation
Camera Parts
See Figure 42.
Item Part Description Quantity Note
— 1122068 KIT, CAMERA ASSY, IN-SIGHT, 5100 —
1 1088453 � CAMERA ASSY,IN-SIGHT,5100 1
4 1085698 � BRACKET,MOUNTING,CAMERA, 1
5 983116 � WASHER,LK,M,SPT,M4,BL 8
6 983137 � WASHER,FLT,M,REG,4,BL 8
7 982504 � SCR,BTN,SKT,M4X16,ZN 4
8 1038767 � NUT, HEX M4.0X0.7 ACORN,300ST-STL 4
9 1066880 � SCR, MACH,HEX HD,M4X12,ST-STL 4
— 1088453 � CAMERA ASSY,IN-SIGHT,5100 —
1A 1088425 � � CAMERA,IN-SIGHT,5100 1
2A 1088450 � � LENS,16MM,IN-SIGHT 1
3A 1088428 � � RING,DIFFUSE,LIGHT,IN-SIGHT 1
4A 1088426 � � COVER,50MM LENSE,IN-SIGHT 1
NS 1088438 � � CABLE,IN-SIGHT,ETHERNET 1
NS 1121328 � � CABLE,IN-SIGHT,CAMERA,DB15 1
NS ‐ ‐ ‐ ‐ ‐ ‐ SOFTWARE,CAMERA,JOB FILE,UNITY 1 A
NOTE A: Visit www.www.cognexsensor.com/support to download software updates.
NS: Not Shown
Unity IC30/IC300 Dispensing System 79
Part 1092353_04� 12/2013 Nordson Corporation
8X TORQUE TO .25 N-m TO .45 N-m
1A
2A
3A
4A
9
7
5
6
4
10
56
1
Figure 42 Camera parts
Unity IC30/IC300 Dispensing System80
Part 1092353_04 � 12/2013 Nordson Corporation
Cable Part Numbers
The cables shown below are for use only in systems using 120‐ohm nickelsensors. Cables for systems using 100‐ohm platinum sensors arecustomer‐supplied.
Part Description Note
1075062 CABLASSY,3COND,18AWG,IEC,PWR,NO PLUG (controller power cable)
1121438 CABLE ASSY,SHIELDED,37,D SHELL (Nordson Corporation robot‐to‐controllercable)
1023676 CABLE,PWR,3‐COND,IEC,9FT10‐IN,BR/BLU/G‐Y (robot power cable)
1121328 CABLE ASSY, DB14 CONN,CAMERA (camera‐to‐controller cable)
1088438 CABLE,IN‐SIGHT,ETHERNET (camera‐to‐PC cable)
1121331 CABLE,SOLENOID,IC30 (IC30 applicator solenoid cable)
1121329 CABLE ASSY, SPL,3CON (IC300 applicator solenoid cable)
164045 CBL,ADPTR, 12P/6S, 10FT, T-STYLE A
1121906 CABLE ASSY,SERIAL MALE TO USB,6FT,UNITY (robot‐to‐PC cable)
NOTE A: This extension cable is used to connect the applicator cordset to the controller. The following additionallengths are available: 117123 (6 ft), 108946 (16 ft), 135972 (24 ft), 753462 (30 ft).
Unity IC30/IC300 Dispensing System 81
Part 1092353_04� 12/2013 Nordson Corporation
Nozzle Part Numbers
See Figure 43.
Part Description Note
322014 Nozzle, Saturn, 0.36 mm (0.014 in.) orifice diameter, 1.27 mm (0.050 in.) engagementlength, yellow/purple
322016 Nozzle, Saturn, 0.41 mm (0.016 in.) orifice diameter, 1.27 mm (0.050 in.) engagementlength, orange/purple
322018 Nozzle, Saturn, 0.46 mm (0.018 in.) orifice diameter, 1.27 mm (0.050 in.) engagementlength, red/purple
322020 Nozzle, Saturn, 0.51 mm (0.020 in.) orifice diameter, 1.27 mm (0.050 in.) engagementlength, beige/purple
1092244 Nozzle, Unity, 1.35 mm (0.053 in.) inner diameter, 1.65 mm (0.065 in.) outer diameter
1092245 Nozzle, Unity, 0.84 mm (0.033 in.) inner diameter, 1.27 mm (0.050 in.) outer diameter
1092246 Nozzle, Unity, 0.61 mm (0.024 in.) inner diameter, 0.91 mm (0.036 in.) outer diameter
1092247 Nozzle, Unity, 0.51 mm (0.020 in.) inner diameter, 0.82 mm (0.032 in.) outer diameter
1092248 Nozzle, Unity, 0.41 mm (0.016 in.) inner diameter, 0.72 mm (0.028 in.) outer diameter
Engagement Length RingOrifice Diameter Ring
1 2
Figure 43 Saturn and Unity nozzles
1. Saturn nozzle 2. Unity nozzle
Optional Accessories
Part Description Note
1010793 Teaching pendant, robot
1108193 Preheater, adhesive cartridge
Unity IC30/IC300 Dispensing System82
Part 1092353_04 � 12/2013 Nordson Corporation
Recommended Spare Parts and Supplies
Equipment Parts Item Note
System 1094186 DRYER,AIR,DESICCANT,INLINE,1/4NPT
Unity controller 1122069 KIT, CONTROLLER,UNITY (includes circuit boards andcontrol panel)
320613 FUSE, 250V, 5A, PC‐MOUNT (3 required)
939306 FUSE, 5X20, 250V, 3.15A (2 required)
1041036 STDBTRY,LITH,COIN,3.0V,225MA (battery)
IC30 applicator 201407 CORDSET KO/MI/0,51/1XNI120/1XTS
1094183 SOLENOID,VALVE,2POSITION,3WAY
1121331 CABLE,SOLENOID,IC30
1095703 KIT,REPL,MODULE,MINIBLUE2,BAS
1086749 HEATER,240V,250W, .50D,4.38LG
941161 O RING,VITON, .750X .938X.094, -116
IC300 applicator 1120235 NEEDLE,PIERCE,IC300CC
1120236 NUT,NEEDLE RETAINER,IC300CC
1120238 SOLENOID,4 PORT,VALVE,3.2W,24V,M PLUG
1121329 CABLE ASSY, SPL,3CON (IC300)
1120241 CAP,END,REACTIVE ADHESIVE,3M
1067912 CORDSET,UA,T‐STYLE,NI120,240V,700W (Ni120IC300 applicators)
1067913 CORDSET,UA,M‐STYLE,PT100,240V,700W, SQR(PT100 IC300 applicators)
1095703 KIT, REPL, MODULE, MINIBLUE2,BAS
1120244 CONN,MALE,6MMTUBEX1/8R,VITON
940090 O RING,VITON,.208ID X .070W,BR,10409
971790 UNION,STRAIGHT,6MM T
940090 O RING,VITON, .208ID X .070W,BR,10409
Camera 1088426 COVER,50MM LENSE,IN‐SIGHT
1088438 CABLE,IN‐SIGHT,ETHERNET
1088439 CABLE,IN‐SIGHT,POWER&I/O,BREAKOUT
Unity IC30/IC300 Dispensing System 83
Part 1092353_04� 12/2013 Nordson Corporation
Technical Data
Unity IC30/IC300 Dispensing System Specifications
Component Item Specification
System Transport temperature ‐45-75 �C (‐49-167 �F)
Storage temperature ‐45-75 �C (‐49-167 �F)
Ambient temperature 0-50 �C (32-122 �F)
Humidity 10-95% non‐condensing
Unity robot Weight 35 kg (77 lb)
Dimensions (l x w x h) 560 mm (W) x 529 mm( D) x 649 mm (H)
Unity controller Operating air pressure 4-8 bar (60-120psi)
Weight 7.2 kg (15.9 lb)
Dimensions (l x w x h) 264 mm (W) x 152 mm (D) x 264 mm (H)
Unity IC30 and IC300applicators
Weight IC30 applicator: 1.6 kg (3.4 lb)IC300 applicator: 3.17 kg (7 lb)
Material compatibility Rated for use with all commercially availablepressure sensitive and EVA hot meltadhesives and polyurethane reactive (PUR)adhesives, excluding any compound thatcontains polyamides
Adhesive viscosity Varies depending on nozzle size and flow rate
Electrical Specifications
Component Item Specification
Unity robot Supply voltage 180-250 VAC, 1‐phase, 50/60 Hz, 200 W
Unity controller Supply voltage 200-240 VAC, 1‐phase, 50/60 Hz, 290�W
Heating zones One (applicator), 1200 W maximum
Control temperature range Ambient to 120 �C (ambient to 250 �F)
Control temperature accuracy 0.5 �C (1 �F)
Unity IC30 and IC300applicators
Supply voltage 200-240 VAC, 1‐phase, 50/60 Hz, 250 W(supplied from controller)
Temperature sensor 120‐ohm nickel RTD
Or
100‐ohm platinum RTD
Camera Supply voltage 24 VDC, 14.4 W (supplied from thecontroller)
Unity IC30/IC300 Dispensing System84
Part 1092353_04 � 12/2013 Nordson Corporation
Dimensions
Figure 44 Robot dimensions (robot part 1094180 shown)
Unity IC30/IC300 Dispensing System 85
Part 1092353_04� 12/2013 Nordson Corporation
Diagram of Internal Pneumatic Connections
(AIR REGULATOR)
(SUPPLY AIR)
(EXHAUST PORT)
(OUT PORT)
(SUPPLY AIR)
(EXHAUST AIR)
( SOLENOID VALVE )
TUBING PROVIDED IN SHIP‐WITH KIT
Figure 45 Diagram of internal pneumatic components
Unity IC30/IC300 Dispensing System86
Part 1092353_04 � 12/2013 Nordson Corporation
Unity Controller Board Configuration Switch Settings
2
1
Figure 46 Unity controller board configuration switch settings
1. Unity controller board 2. Location of the IN configurationswitches
Unity IC30/IC300 Dispensing System 87
Part 1092353_04� 12/2013 Nordson Corporation
Schematic
The schematic on the next page is provided for your reference as needed.
Unity IC30/IC300 Dispensing System88
Part 1092353_04 � 12/2013 Nordson Corporation
Figure 47 Unity system schematic