UNISAW® Accessories

DELTA

®

and BIESEMEYER®

products can be found on www.DeltaMachinery.com

DELTA

®

and BIESEMEYER®

products can be found on www.DeltaMachinery.com

UNISAW® Accessories

36-805

Zero Clearance Throat Plate

» Designed to support the material on both sides of the saw kerf to prevent tearout

» 1/2 in. thick melamine-coated solid phenolic resin blanks

36-0944Standard Replacement Throat Plate

36-808

Dado Throat Plate

» For use with stacked dado cutters

» Phenolic construction for minimal tearout

50-479

5 in. to 4 in. Port Reducer

» This fitting allows you to reduce down from a larger main line to smaller branch lines

36-201

Standard & Dado Arbor Nut Assembly

» For single-blade operations, an arbor nut coupled with a 5/16 in. x 2 1/2 in. dia. machined steel flange provides rigid blade stabilization

» For stacked dado applications, switch to the separate arbor nut without a flange

» Each features a wide knurled grip with hex-head for final tightening

36-0101

Table Saw Arbor Wrench

» Extra-long handle keeps your hand away while changing the blade

36-055

Feather Board

» Universal T-track compatibility for improved cut control

» Design allows stock to pass in one direction and causes resistance if moved in the other direction; preventing kickback

36-050

Push Stick

» Device used to push stock while keeping hands away from the blade

» Designed to optimize control of your workpiece

34-928

Deluxe Miter Gauge

» Designed with the professional in mind

» Oversized grip and positive stops at all popular miter angles

34-568

Clamp Attachment

» Holds work securely for accurate miter and cut-off operations

» For use with Model 34-928 miter gauge

78-967BIESEMEYER® Medium and Thick Kerf Riving Knife

78-965

BIESEMEYER® Thin Kerf Riving Knife

DELTA

®

and BIESEMEYER®

products can be found on www.DeltaMachinery.com

UNISAW® Accessories

50-2000 / 50-257

Mobile Base

» Enhances mobility in the workshop

» 50-2000 for use with older model UNISAW®

» 50-257 for use with 36-L352 or 36-L552 UNISAW® models

78-9450

BIESEMEYER® Rear Outfeed Table

» Adds an additional 4 ft. x 44 in. of work support

» Compatible with any DELTA® UNISAW® or other DELTA® 12 in. or 14 in. saws

78-864B / 78-918B

BIESEMEYER® Universal Table Board

78-864B – For the 36 in. BIESEMEYER® Fence System Table Board L X W X H: 37 in. X 35 1/2 in. X 4 1/2 in.78-918B – For the 52 in. BIESEMEYER® Fence System Table Board L x W x H: 52 in. x 37 in. x 4 1/2 in.

» Constructed of a hardwood alder frame and laminated particle board

» Laminate siding on three sides

» Backer-board underside

78-138B / 78-055B

BIESEMEYER® Fence Rails

78-138B – For 36 in. BIESEMEYER® Fence System

78-055B – For 52 in. BIESEMEYER® Fence System

DELTA

®

and BIESEMEYER®

products can be found on www.DeltaMachinery.com

Premium Accessories

34-184

Universal Tenoning Jig

» Has ergonomic handles, quick release coarse adjustment, micro adjustment to .004 in.

» Universal miter bar for use with all table saws with

» 3/8 in. x 3/4 in. miter slots

50-531

4 in. x 20 ft. Hose

50-530

4 in. x 10 ft. Hose

50-786The Perfect 1.5 HP Dust Collector for the DELTA

®

UNISAW®

78-939

BIESEMEYER® Cut-off Fence

» Quick-release clamp for fast and safe setups

» Acts as a stand off to keep material away from the fence when using a miter gauge

» Smooth sliding surface. The one inch dimension can be easily added when indexing the hairline on your BIESEMEYER® fence with the scale on the system ft.s guide

78-919B

BIESEMEYER® Fence System

» The most precise fence in the industry

» Fence body constructed from .083 gauge steel

» Laminated 9-ply Birch plywood sides are durable and do not mar easily

» Accurate repeatability, eliminating the need for using a hand-held tape to square and set the fence

78-940

BIESEMEYER® Auxiliary Fence

78-970BIESEMEYER® Standard Accessory Drawer

» Storage designed for the woodworker

» Easily accommodates up to five saw blades, two riving knives, throat plate, push stick, wrench/ arbor nut and complete guarding assembly

DELTA

®

and BIESEMEYER®

products can be found on www.DeltaMachinery.com

Service Parts

The riving knife supplied with the DELTA® UNISAW® is the correct size for the blade supplied with the saw. If a different blade is used, check the blade body, or plate, thickness and the blade kerf, or cutting width marked on the blade or on the blade packaging. The riving knife thickness must be greater than the body thickness and less than the kerf width as shown in Fig. 1. If it is not, the riving knife MUST be replaced with one that has the correct thickness. The riving knife provided with this saw is marked as follows: 2.2 mm THICK RIVING KNIFE. ONLY USE FOR 10 in. BLADE WITH 2.4 mm minimum KERF WIDTH AND 1.7 mm maximum BODY THICKNESS. (See Fig. 2) The riving knife (available as an accessory from DELTA®) is marked as follows: 2.8 mm THICK RIVING KNIFE. ONLY USE FOR 10 in. BLADE WITH 3.0 mm minimum KERF WIDTH AND 2.5 mm.

MAX. BODY THICKNESS–All DELTA® blade body thickness and kerf widths are provided at www.DeltaMachinery.com. If a different blade is used and the body thickness and kerf width dimensions are not provided, use the following procedure to determine the correct riving knife thickness:

» STEP 1: Measure the body thickness of the blade.

» STEP 2: Make a shallow cut in scrap material and measure the kerf width.

» STEP 3: Select the riving knife as shown in Fig. 1.

» STEP 4: Slide the riving knife through the shallow cut (Fig. 3) made in step 2 to confirm the correct riving knife has been selected. The riving knife should not bind or drag through the cut.

IMPORTANT NOTE: If any dragging or binding of the material is encountered as it reaches the riving knife, turn unit off and disconnect machine from power source. Repeat steps 1–4 to make the proper riving knife selection before attempting another cut.

Service Part A28410

Rise-and-Fall Split Guard Assembly

» Tool-free split guard design allows easier line of site with the blade and work-piece

Service Part A28414

Anti-Kickback Pawls

» Design allows stock to pass in one direction and causes resistance if moved in the other direction; preventing kickback

ServiceNet is the Official Parts & Service Site For DELTA® and is your one-stop for all your parts needs. www.DeltaMachinery.com/parts

Riving Knife Selection

Copyright © 2012 DELTA® Power Equipment Corporation

92-393B - 03-01-2012